Download - LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK
![Page 1: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/1.jpg)
LOFAR Antenna Systems
Dion Kant, Wim van Cappellen
AAVP 2010
8 – 10 December 2010, Cambridge, UK.
![Page 2: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/2.jpg)
DK, WvC, 2010/12/10AAVP 2010
Outline
• Requirements and design considerations
• Low Band Antenna
• High Band Antenna
• Summary
![Page 3: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/3.jpg)
DK, WvC, 2010/12/10AAVP 2010
Key LOFAR Antenna requirements
• Frequency band: 15 – 240 MHz
– Excluding FM-band 80 – 110 MHz
• Sky noise dominated
• Large collecting area
• Large beamwidth (120 deg)
• Height < 2.0 m
• Cost effective
![Page 4: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/4.jpg)
DK, WvC, 2010/12/10AAVP 2010
LOFAR: 2 antennas
• Two antennas:
– Low Band Antenna (LBA) 15 – 80 MHz
– High Band Antenna (HBA) 110 – 240 MHz
• Because:
– Completely different sky noise temperatures in low and high bands
– One antenna could not meet performance requirements
over whole band
– Antenna configuration can be different for LBA and HBA:
• If one antenna was used, the array would be too dense at 15 MHz or too sparse at 250 MHz.
– RFI (FM band) in the middle of LOFAR band
![Page 5: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/5.jpg)
DK, WvC, 2010/12/10AAVP 2010
Low Band Antenna• 96 Low Band Antennas per station • Station diameter: 45 – 85 m (LBA)• Sparse pseudo-random configuration
![Page 6: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/6.jpg)
DK, WvC, 2010/12/10AAVP 2010
High Band Antenna
High Band Antenna
• 768 x 2 dipoles per station
• Sparse rectangular grid
• Analog beamformer per tile (4x4 elements)
![Page 7: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/7.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA and HBA in a nutshell
• LOFAR Low Band: 15 – 80 MHz:
– Tsky varies from 125,000 to 1,750 K
– Array must be very sparse at lowest frequency for high Ae
– Per-element digitization
– Randomized configuration to smear out grating lobes
– Electrically small elements (height <0.1 at lowest freq)
• LOFAR High Band: 120 – 240 MHz
– Tsky varies from 600 K to 110 K
– Large number of antennas needed for high collecting area
– RF beamforming within tile (16 elements), digitization per tile
– Regular configuration to reduce costs and ease calibration
– Grating lobes suppressed by station rotation
![Page 8: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/8.jpg)
DK, WvC, 2010/12/10AAVP 2010
Low Band Antenna
• Frequency range: 15 – 80 MHz ( from 20 m to 3.75 m)
• Active balun:
– Senses open terminal voltage of antenna
– Small wrt wavelength to meet environmental requirements
– Inefficient radiator at low frequencies, but acceptable due to
very high sky noise
– But: No RFI filtering possible ahead of active circuits
• Low frequency performance set by Tsys
• High frequency performance set by pattern degradation
![Page 9: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/9.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA noise performance
• Single element simulation and measurement
![Page 10: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/10.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA station system temperature
• Estimated Tsys from measured Ae/Tsys of LOFAR station towards zenith and simulated Ae
• Simulated Tsys (=Tant + Tsky from previous slide)
• Excellent agreement!
• Deviation at 80 MHz due
to receiver filter (not
included in simulation).
Tsky
Estimated Tsys
Simulated Tsys
![Page 11: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/11.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA Station Simulation
• Station simulation (96 elements)
– Using combined EM and circuit simulation
(using in-house CAESAR code)
– Results shown at 60 MHz
• Used to optimize station configuration
– dense vs sparse
– Regular vs irregular
Aeff Tsys Aeff/Tsys
![Page 12: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/12.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA Temperature dependency
• Gain temperature dependency– Measured from -30 to 80 °C– Max. change rate: 0.005 dB / °C (0.1% / °C)
• Phase temperature dependency
– Max. change rate: 0.06 deg / °C
![Page 13: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/13.jpg)
DK, WvC, 2010/12/10AAVP 2010
LBA Environmental tests
• Lifetime > 15 years
• Suppliers indicate their materials will be OK, but cannot guarantee.
• The LBA has been extensively tested:
– Ozone, salt-spray and SO2
– Solar radiation (1000 hr)
– Tent peg pulling test
– Dipole wire pulling test
– Liquid penetration test of molded LNA
![Page 14: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/14.jpg)
DK, WvC, 2010/12/10AAVP 2010
High Band Antenna
• Fat dipole antenna elements in 4x4 tiles
• Rectangular array
• Element spacing (1.25 m) = /2 at 120 MHz
• True time delays integrated in elements
• Beamformer is ‘simple’ combiner
• ‘Matched’ LNA
• Per tile digitization
![Page 15: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/15.jpg)
DK, WvC, 2010/12/10AAVP 2010
HBA Tsys for various scan angles
• Simulated Tsys
![Page 16: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/16.jpg)
DK, WvC, 2010/12/10AAVP 2010
HBA station estimated Tsys
• Tsys estimated from measured Ae/Tsys and simulated Ae.
• At this scan angle (7° from zenith) the system is
sky noise dominated below 150 MHz.
![Page 17: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/17.jpg)
DK, WvC, 2010/12/10AAVP 2010
HBA Station rotation
• HBA tiles have a different orientation in every station
• The product beam suppresses grating lobes
• Individual dipoles are rotated back for calibration purpose
x =
![Page 18: LOFAR Antenna Systems Dion Kant, Wim van Cappellen AAVP 2010 8 – 10 December 2010, Cambridge, UK](https://reader036.vdocuments.us/reader036/viewer/2022062804/56649da85503460f94a956e8/html5/thumbnails/18.jpg)
DK, WvC, 2010/12/10AAVP 2010
Summary
• The LOFAR antenna design is highly sky noise dominated:
– High sky noise enables electrically small LBA in a very sparse configuration
– Lower sky noise in high band forced ‘matched’ LNA’s
• But there were many more aspects impacting the design:
– RFI
– Required array configuration
– Performance requirements
– Reliabilioty, lifetime
– Maintainability
– Costs
• LOFAR successfully demonstrated a split-band design