Load Chart Exercise
Workbook
(508) 212-4735
Copy Right 2017
For Exam Use Only
Deduct 120 lb from all "on rubber" capacities whenboom extension is stowed on base boom.
Maximum hydraulic pressure is 3,000 psi.
Personnel bucket capacity, outriggers extended,300 lb per bucket, 600 lb total. The booms on thisunit are all steel and have no line voltage rating.
Deck capacity 12,000 lb (centered over axle).
Capacities below bold line are limited by tipping.Other capacities are limited by structural or hydrauliccapability.
All capacities apply to operation on firm level surfaces.
The load hoist line on this unit must be 9/16" diameter6 x 37 IWRC EIP wire rope or equivalent with aminimum breaking strength of 31,500 lb.
Operation:
Carry capacity speed limit 3 mph.
1. Read and understand owners manual before operating the crane.2. Check level of hydraulic oil daily.3. Check unit for visible effects and loose parts.4. Start engine.5. Set vehicle park brake securely.6. Extend outriggers to solid footing.7. Operate all hydraulic controls slowly and deliberately for smooth motion.
Capacities on outriggers are 85% of tipping loads.Capacities on rubber are 75% of tipping loads.
Use single part load line for loads to 9,000 pounds.Use two part load line for loads to 17,000 pounds.
RATED LIFTING CAPACITIES IN POUNDS
9,500
8,500
6,000
4,150
3,025
2,350
1,850
1,550
1,300
1,100
925
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
ONRUBBER
ONOUTRIGGERS
ONRUBBER
ONOUTRIGGERS
10 FT BOOM EXTENSIONINSTALLED
3-SECTIONBOOM
LOADRADIUS
INFEET
17,000
14,500
10.250
7,700
6,550
5,550
4,450
3,950
3,250
2,875
2,475
7,000
6,000
5,000
4,000
3,275
2,600
2,125
1,800
1,525
1,275
1,050
850
700
600
525
450
7,000
6,000
5,000
4,000
3,450
3,050
2,700
2,250
2,250
2,250
2,250
2,250
2,000
1,775
1,625
1,400
BRODERSON IC-80-2D NOTES
DEDUCTIONS FORLOAD HANDLING DEVICES
10-Ton 1-Sheave Block . . .5-Ton Ball. . . . . . . . . . . . . . .
200 lbs150 lbs
For Exam Use Only
Telescoping Boom Crane Load Chart Problems NET LOAD KNOWN
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Telescoping Boom Crane
Load Chart Problems
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Courtesy of Terex
For Exam Use Only
For Exam Use Only
Telescoping Boom Crane Load Chart Problems NET LOAD KNOWN
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Telescoping Boom Crane
Load Chart Problems
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Courtesy of Terex
1. A freely suspended load is a load hanging free with no direct external force applied except by the hoist rope.
2. Crane load ratings are based on the crane being leveled and standing on a firm, uniform supporting surface.
3. Use of jibs, lattice-type boom extensions, or fourth section pullouts extended is not permitted for pick-and-carry operations.
4. The use of more parts of line than required by the load may result in having insufficient rope to allow the hook to reach the ground.
5. Do not elevate the boom above 60° unless the boom is positioned in-line with the crane’s chassis or the outriggers are extended. Failure to observe this warning may result in loss of stability.
6. CRANE LOAD RATINGS MUST NOT BE EXCEEDED. DO NOT ATTEMPT TO TIP THE CRANE TO DETERMINE ALLOWABLE LOADS.
7. When either radius or boom length, or both, are between listed values, the smaller of the two listed load ratings shall be used.
8. Do not operate at longer radii than those listed on the applicable load rating chart (cross-hatched areas shown on range diagrams).
9. The boom angles shown on the capacity chart give an approximation of the operating radius for a specific boom length. The boom angle, before loading, should be greater to account for boom deflection. It may be necessary to retract the boom if maximum boom angle is insufficient to maintain rated radius.
10. Power telescoping boom sections must be extended equally.
11(a). Rated loads include the weight of hook block, slings, and auxiliary lifting devices. Their weights shall be subtracted from the listed rated load to obtain the net load that can be lifted.
11(b). When lifting over the jib the weight of any hook block, slings, and auxiliary lifting devices at the boom head must be added to the load.11(c). When jibs are erected but unused add two (2) times the weight of any hook block, slings, and auxiliary lifting devices at the jib head to the load.
12. Rated loads do not exceed 85% on outriggers or 75% on tires, of the tipping load as determined by SAE Crane Stability Test Code J765a. Structural strength ratings in chart are indicated with an asterisk(*).
13. Rated loads are based on freely suspended loads. No attempt shall be made to drag a load horizontally on the ground in any direction.
14. The user shall operate at reduced ratings to allow for adverse job conditions, such as: Soft or uneven ground, out of level conditions, high winds, side loads, pendulum action, jerking or sudden stopping of loads, hazardous conditions, experience of personnel, two-machine lifts, traveling with loads, electric wires, etc.
15. The maximum load which can be telescoped is not definable, because of variations in loadings and crane maintenance, but it is permissible to attempt retraction and extension if load ratings are not exceeded.
16. Load ratings are dependent upon the crane being maintained according to manufacturer’s specifications.
17. It is recommended that the load handling devices, including hooks and hook blocks, be kept away from boom head at all times.
18. Do not lift with outrigger beams positioned between the fully extended and intermediate (pinned) positions.
SELECTED NOTES • TEREX RT 555
Telescoping Boom Crane Load Chart Problems NET LOAD KNOWN
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Telescoping Boom Crane
Load Chart Problems
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Courtesy of Manitowoc, LLC
Note: Boom angles are in degrees.
FULL HYDRAULIC SELF-PROPELLED CRANE • 75 TON CAPACITYPCSA CLASS 10-336 • 85% OF TIPPING
RT875E
RT875
Pounds
41.3-90 ft. 18,000 lbs Stationary 360º
FeetMain Boom Length in Feet
41.3 50 60 *70 80 90
12 49,200(67.5)
40,750(72)
15 39,150(63)
35,700(68.5)
20 24,200(54.5)
24,350(62)
22,800(67.5)
22,000(71)
25 16,200(44.5)
16,200(55)
15,600(62)
15,950(66.5)
15,850(70)
30 11,250(31.5)
11,250(47)
10,950(56)
10,650(62)
11,600(66)
12,150(69.5)
35 7,900(37.5)
7,690(49.5)
7,270(57)
8,420(62)
8,820(66)
40 5,490(24.5)
5,280(42.5)
4,880(52)
6,020(58)
6,330(62)
45 3,430(34)
3,110(46)
4,130(53)
4,480(58.5)
50 1,350(22)
1,740(39.5)
2,610(48.5)
3,040(54.5)
55 1,360(43)
1,070(50)
Minimum boom angle (deg.) forindicated length (no load) 21 38.5 42 49
Maximum boom length (ft.) at 0deg. boom angle (no load) 50
#9005
Weight Reductions for Load Handling Devices
33 FT.-56 FT. FOLDING BOOM EXTENSION
.bl 007,3- )detcerE( noisnetxE.tf 33*
.bl 038,7- )detcerE(noisnetxE .tf 65*
.bl 053,01- )detcerE tresni 1( .tf 67*
.bl 003,31- )detcerE stresni 2( .tf 69*
*Reduction of main boom capacities(no deduct required for stowed boom extension)AUXILIARY BOOM NOSE 136 lb.
HOOKBLOCK AND OVERHAUL BALL:+.bl 572,1evaehS 4 ,noT 57
10 + .bl 865llaBluahrevO ,noT
Permissible NominalHoists Cable Specs Line Pulls Cable Length
3/4" (19 mm) 6x37 Class,Main EIPS, IWRC Special Flexible 16,800 lb. 600 ft.
Min. Breaking Str. 58,800 lb.
3/4" (19 mm) Flex-X 35Main & Aux. Rotation Resistant (non-rotating) 16,800 lb. 607 ft.
Min. Breaking Strength 85,800 lb.
The approximate weight of 3/4" wire rope is 1.5 lb./ft.
Hookblock
E
Telescoping Boom Crane Load Chart Problems NET LOAD KNOWN
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Manual Section: Extended Retracted
Net Load to be lifted: Lbs
Boom Extension: Stowed Erected + Lbs
Jib: Stowed Erected + Lbs
Auxiliary Boom Head: Erected Off + Lbs
Part(s) Wire Rope Ft Beneath: + Lbs
Ton Block: + Lbs
Ton Ball: + Lbs
Rigging: + Lbs
Gross Load: Lbs
Max. Radius over : Feet
Lowest Boom Angle: Degrees
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Telescoping Boom Crane
Load Chart Problems
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Problem Crane
Outriggers Fully Extended Mid Pt. Retracted On Tires
Hoisting From: Main Boom Manual Section Ext. Jib (Offset °)
Boom Length: Ft Radius: Ft Boom Angle: Degrees
Manual Section: Extended Retracted
Gross Capacity over the : Lbs
Boom Extension: Stowed Erected — Lbs
Jib: Stowed Erected — Lbs
Auxiliary Boom Head: Erected Off — Lbs
Part(s) Wire Rope Ft Beneath: — Lbs
Ton Block: — Lbs
Ton Ball: — Lbs
Rigging: — Lbs
Net Capacity: Lbs (Maximum Net Load)
Block/Ball Lbs
+ Rigging Lbs
+ Net Load Lbs
= Susp. Wt. Lbs ÷ SWL Lbs = Minimum Parts of Line
Set up your own problems
Set up your own problems
Set up your own problems
Set up your own problems