Download - Internship Report
INTERNSHIP REPORT
Pakistan Pertroleum Limited
Prepared by:
Sadia Urooj
Submitted to:
Dr. Shujjat Ahmed,
Manager Process Engineering (MPrE).
University of Karachi
Pakistan Petroleum Limited
ACKNOWLEDGEMENT
All praise unto Almighty Allah, the Lord of all worlds, who endowed me with the ability to
complete successfully this period as internship.
“My Lord, I have never been unblessed in my prayer to you.”
I am extremely thankful for the co-operation and help provided byDr. Shujjat Ahmed
(MPrE), Mr. Farooq Azam Shah (DCE Pr), Mr. Imran Bukhari (EPr), Mr. Athar (TrE
Chem) for spending their valuable time and responding to my queries and giving me an
insight how an organization is run, what are the important principles of a working
environment, how projects are designed, their implementation and what are the softwares
used in executing these tasks. I feel myself an opportunist after served the high tech
environment in PPL which shall be a guideline in my future career.
Last but not the least, I am thankful to all those who always have guided me at their best.
Sadia Urooj
Student, Chemical Engineering (Batch 2009)
University of Karachi
2
TABLE OF CONTENTS
S.No
DESCRIPTION Page#
1. Introduction
1.1.General (Oil & Gas Industry Work Flow)1.2.Plant Operations1.3. PPL Process Engineering Department major scope:
- Technical Services- Process Design
5
2. Introduction With Process Engineering
2.1. Fundamentals of Process Design 2.2. Standards and Codes Frequently used in Process Design &
Their Application 2.3. Introduction with Unit Operation & Unit Processes in PPL Plants
14
3. Preparation Of Process Design Documents & Their Standard Requirements
3.1. Schematic 3.2. PFDs 3.3. H&MB 3.4. P & IDs 3.5. Plot Plan 3.6. Process Simulation (HYSYS)
20
4. Process Design Calculation Of Pipelines System & Major Process Units
4.1. Introduction with Transient Flow Regimes 4.2. Hydraulic Calculation of Process Piping 4.3. Separators (2-Phase, 3-Phase, Knock Out, Scrubbers etc.) 4.4. Heat Exchangers (S&T, Air Coolers etc.) 4.5. Towers (De-Ethanizer, De-Butanizer, Stripper) 4.6. Pumps (Centrifugal, Reciprocating etc.) 4.7. Compressors (Centrifugal, Reciprocating etc.) 4.8. Storage (LPG, NGL, Diesel, Water etc.)
22
ConclusionReferencesAnnexures
424344
3
ANNEXURES
Annexure A: Electrical standards and approved codes of practice
Annexure B: Block Flow Process Diagram
Annexure C: Block Flow Plant Diagram
Annexure D: Process Flow Diagrams (PFDs)
Annexure E: Piping and Instrumentation Diagram (P&IDs)
Annexure F: Plot Plan
Annexure G: Separator Sizing
Annexure H: Compressor Design
4
INTRODUCTION
Pakistan Petroleum Limited
Pakistan Petroleum Limited invariably known as PPL is the pioneer in the gas production of
the country, contributing about one fourth of total gas supplies, besides producing crude oil,
condensate and LPG. Pakistan Petroleum Limited has been in the business of exploration
and production since 1950 with the establishment of a public limited company through
major shareholding of a Britain based company (Burmah Oil Company).
Presently PPL's share in the country's total natural gas production stands at around 24
percent. The company operates the largest gas field at Sui and five others at Kandhkot,
Hala, Chachar, Adhi, and Mazarani. It holds working interest in 12 partner operated fields
including Qadirpur, Sawan, Nashpa, Latif etc. PPL-operated fields produce an average of
one bcfd which is sold to the company's main clients: Wapda, SSGC and SNGPL.
The exploration portfolio of the company consists of 35 exploration blocks including
offshore block Indus-G. Pakistan Petroleum Limited is the operator in 19 of them, while it
has working interest in 15 of them as well. These numbers also include the exploration
license in Yemen, which is a joint venture between PPL, OMV and Yemen General
Corporation for Oil and Gas. However, due to security issues, progress in this regard has
been halted completely in recent times.
1.1. General (Gas Industry Work Flow)
Oil and gas field production and processing operations are primarily defined by the
following activities:
Exploration and production (E&P) ;
Processing;
Storage and transport; and
Wastewater.
1.1.1. EXPLORATION AND PRODUCTION
5
The oil and gas field production and processing operations begin with exploration to locate
new sources of crude oil and natural gas. Seismic and other geophysical methods are used
to locate subterranean formations that signal the potential presence of oil and gas
reservoirs. When potential sources are located, wells are drilled to confirm the presence of
oil or gas and to determine whether the reserves are economically sufficient to support
production.
Once a well has been completed and is producing crude oil or natural gas, an arrangement
of high-pressure valves termed a "Christmas tree" is installed to control production. As the
well ages, an artificial lift device may be needed to help bring product to the well surface.
1.1.2. PROCESSING
1.1.2.1. CHEMICAL INJECTION SKIDS
Chemical agents employed in field processing include drilling fluid additives, methanol
injection for reservoir stimulation, glycol injection for hydrate inhibition, produced water
treatment chemicals, foam and corrosion inhibitors, de-emulsifiers, desalting chemicals and
drag reduction agents (DRAs). Chemicals are frequently administered by way of chemical
injection skids.
1.1.2.2. WELL STREAM SEPARATION
The first step in processing the well stream is to separate the crude oil, natural gas and
water phases into separate streams.
6
1.1.2.3. FIELD STORAGE TANKS
Crude oil, natural gas liquids (NGLs) and water are stored in oil and gas fields. Field
storage consists of smaller vessels associated with oil, gas and water processing.
1.1.2.4. WATER PROCESSING
Water collected from process operations contains hydrocarbon concentrations too high for
safe discharge thus it requires treatment. Suspended hydrocarbon droplets in water also
hinder well-injection.
1.1.2.5. CRUDE DEHYDRATION, DESALTING & STABILIZATION
Separated crude may contain up to 15% water which exists in an emulsified form. De-
emulsification processes are accomplished using chemical agents and heat. Crude
desalting removes both salt and the residual free water.
By removing dissolved gases and hydrogen sulfide, crude stabilization and sweetening
processes diminish safety and corrosion problems.
1.1.2.6. VAPOR RECOVERY UNIT
If allowed to escape into the atmosphere, hydrocarbon vapors diminish income through loss
of hydrocarbon volume and create fire hazards and pollution problems. A Vapor Recovery
Unit (VRU) collects vapors from storage and loading facilities, reliquefies the vapors and
returns the liquid hydrocarbons back to storage. Methods to recover vapors include
absorption, condensation, adsorption and simple cooling.
1.1.2.7. GAS DEHYDRATION
Natural gas dehydration removes hydrates which can grow as crystals and plug lines and
retard the flow of gaseous hydrocarbon streams. Dehydration also reduces corrosion,
eliminates foaming, and prevents problems with catalysts downstream. Natural gas is
dehydrated according to the customer’s specifications for maximum water content.
1.1.2.8. SOUR GAS TREATMENT
Pipeline specifications require removal of the harmful acid gases carbon dioxide (CO2) and
hydrogen sulfide (H2S). H2S is highly toxic and corrosive to carbon steels. CO2 is also
7
corrosive and reduces a gas’s BTU value. Gas sweetening processes remove these acid
gases and make natural gas marketable and suitable for transportation.
1.1.2.9. NGL RECOVERY
Separating the hydrocarbons and fluids from pure natural gas produces pipeline quality dry
natural gas. The two principle techniques for removing Natural Gas Liquids (NGLs) are the
absorption and the cryogenic expander method.
1.1.2.10. PUMPS & COMPRESSORS
Pumps are used throughout field operations for moving drilling fluids, crude oil and
produced water. Compressors increase the pressure of natural gas to facilitate pipeline
transport.
1.1.2.11. LIQUID AND GAS FLOW
The flow of process liquids and natural gas in field operations must be monitored for safety
and efficiency.
1.1.2.12. TANK BLANKETING
Nitrogen is commonly used as a tank blanketing gas in order to prevent ignition of
flammable liquids, provide an oxygen and moisture barrier, inhibit vapor loss and maintain a
tank’s pressure balance.
1.1.2.13. FLARE STACKS & HEADERS
Hydrocarbon gases are often flared in a high-temperature oxidation process which burns
combustible components of waste.
1.1.3. STORAGE AND TRANSPORT
Storage tanks are used to store crude oil, liquefied natural gas (LNG), water or brine,
process condensate, as well as other materials used or generated during the production of
oil and natural gas. Crude oil is transported from production operations to refineries by tank
trucks, rail cars, tankers, barges, and pipelines. Loading methods include splash loading,
submerged pipe fill, and bottom loading. Natural gas is transported by pipeline.
8
Pipeline pigging operations are conducted to assist in product transfer and product
separation, as well as for maintenance activities. A pig is a physical device which varies in
size and shape and can be made of a variety of materials such as plastic, urethane foams,
and rubber. Pigs can be solid, inflatable, foam, or made of a viscous gel. The specific
design of a particular pig depends upon the pipeline as well as the purpose of the pigging
operation.
Three types of pigging operations occur in pipelines at oil and gas field production and
processing facilities: product transfer, product separation, and maintenance. Pigging
following product transfer is used to remove residual product from the pipeline after loading
occurs. Pigs can also be used for product separation to transport more than one product,
such as oil, gas, or condensate as well as for maintenance activities such as pipeline
cleaning, gauging, or dewatering. During pigging operations, a pig is inserted into the
pipeline and is forced through the pipeline by a compressed gas, such as nitrogen. When
the pig gets to the end of the line, it is trapped in a receiver. The gas is then bled off from
behind the pig. Depending on the specific pigging operation, waste removed from the
pipeline may also be an issue.
1.1.4. WASTEWATER
During oil and gas field production and processing operations, wastewater is generated
from processes such as product separation and glycol dehydration. The wastewater may be
treated on-site or it may be forwarded to an approved wastewater treatment facility.
Many types of units are used to treat, store, and transfer wastewater on-site. Some of these
units include sumps, pits, storage tanks, brine tanks, and oil/water separators which may be
in primary, secondary or tertiary treatment service.
1.2. Plant Operations
Operation is a complex of activities performed by the operating staff to ensure safe and
reliable operation of the plant equipment.
Plant operation has certain objectives.
Specifications: To meet the sales specifications.
9
Capacity: Run at the designed flow rates.
Flexibility: If operating ranges change, it can operate yet.
Regulations: By-products specifications should be met. All effluents must meet the
environmental conditions based upon NEQS.
Safety system: Overall Occupational Health and Safety (OHSAS).
There are three types of plant operations, normal operations, shutdown and start up, and
trouble-shooting.
NORMAL OPERATION
It’s based on SOPs. Standard operating procedures should cover three main areas of
operation. First is the safety considerations associated with the process. The operator
must understand the process flow sheet and have a mental picture of how the plant is
structured and how it operates. He must know where the pressure relief valves and
rupture disks are located and where the releases will go in the event their operation is
triggered by an upset in the process. The second element that needs to be covered in
written standard operating procedures is a description of the control system. The third
element in standard operating procedures involves specifying the standard operating
conditions.
SHUTDOWN AND START UP
As takeoff and landing are most hazardous operations for an aircraft so in a process plant
the hazard is greater during start-up and shut-down.
Column Startup and Shutdown
A column startup usually consists of the following steps:
1. Commissioning
2.Pressure-up
3.Column Heating (and/or cooling)
4.Introduction of feed
5. Introducing heating and cooling sources
6. Bringing column to desired operating conditions
1 0
Similarly, column shutdown usually consists of the following steps:
1. Reducing column rates
2. Shutting down heating and cooling sources
3. Stopping feed
4. Draining liquids
5. Cooling (or heating) the column
6. Bringing the column to atmospheric pressure
7. Eliminating undesirable materials
8. Preparing for opening to atmosphere
Other activities required for carrying out a proper startup or shutdowns include:
Preparation of operating, startup, shutdown (normal and emergency) and maintenance
procedures and checklists for each phase
Selection and training of startup/shutdown team
Planning and coordinating all activities, developing individual tasks and objectives, etc
Securing any raw materials, catalysts, equipment, and spare parts required.
TROUBLE-SHOOTING
Trouble-shooting is equipment based. Trouble-shooting is more in rotary equipments than
stationary equipments. In trouble-shooting, we do root cause analysis.
Trouble-Shooting Checklist for Amine Systems
Dirty Amine
Cyanides
Amine color and solids concentration
Inadequate filtering
Corrosive amines
Regenerator feed temperature too high
High velocities
Stress cracking
Reboiler corrosion
1 1
Corrosion inhibitor
Condensate backup in channel head
Regenerator reflux rate too low
Superheated reboiler steam
Reclaimer operation
High S2O3 levels
Soda ash addition rate
Diluent water rate
Tubes not submerged in liquid
Energy reduction
Minimize CO2 recovery
Cut amine circulation
Reduce reboiler steam
Foaming in scrubbers
High N2 in refinery effluent
Scrubber pressure drop
Dirty amine
Excessive concentrations of silicone or inhibitor
Charcoal filter
Condensing hydrocarbons
Extraneous surfactants
Plugged level control traps
Liquid-liquid scrubbers
Loss in amine strength
Amine cooler leaking
Reboiler or reclaimer leaking
Condensate make-up or valve open
Test with tracer chemical
Poor sweetening
1 2
Leaking cross exchanger
Regenerator reflux rate too low
Amine degraded
COS in treated propylene
1.3. PPL Process Engineering Department Major Scope
1.3.1. TECHNICAL SERVICES
As a process engineer the overall objective is to ensure optimum running of theprocessing
units in terms of capacity utilization, energy efficiency, equipment life, to provide timely
assistance to operational problems, production planning, economic operating modes and
quality control.
Process simulation techniques are used for optimizing and troubleshooting the process of
the plant through one of the major simulation tool HYSYS.
Designing, evaluation and modifications for the plants to ease the operation and optimize
the performance requiring good knowledge of hydraulic calculations. Updating daily plant
monitoring sheet and wellness report of the department.
1.3.2. PROCESS DESIGN
As a process engineer , the design of any process contribute a great deal in the
development of industrial output and satisfactory as well as safe operation of the plant. The
process engineering department of PPL contribute a lot in designing , increasing
production, assisting new projects , meeting the standards , gathering data from standard
procedure and coming up with adequate and economical plant design.
INTRODUCTION WITH PROCESS ENGINEERING
1 3
2.1. Fundamentals of Process Design
In business a process is any sequence of events or actions that transforms inputs into
outputs. For example, a car business takes in metal and labor and transforms it into cars
through a process of car manufacture. Processes are designed so as to make most efficient
use of resources, including time, labor and capital.
2.2.1. DESIGN BRIEF
The first stage in process design is the design brief. The design brief is usually achieved
through extensive consultation among the clients who will be using the process, and
whoever will be implementing the process. The design brief includes information about the
requirements, specifications, costs, schedule and objectives of the process.
2.2.2. SPECIFICATION
Included within the design brief is the specification. The specification is a detailed
description of the properties that the process needs to possess. The specification will
establish in detail the criteria by which the success or failure of the design of the process
will be judged.
2.2.3. CONCEPT
The concept is a high-level description of how the process will function. The concept stage
of process design involves a great deal of abstraction. Complex subsystems of the process
are presented as "black boxes" with certain inputs and certain outputs. The goal of the
concept stage of process design is simply to ensure that the design as specified is feasible,
and to identify any major problems with implementing the specified process design.
2.2.4. DETAILS
After the concept has been established, the subsystems can be removed from their black
boxes and the work of designing the process at a detailed level can begin. This part of
designing processes generally takes the longest, as consideration has to be made of all the
detailed elements of the process subsystems.
2.2.5. TESTING
As the process is implemented, each subsystem has to be tested to ensure it works
properly. Once all the subsystems of the process have been implemented, testing has to
1 4
happen to ensure that everything works as required by the specification. If things do not
work as required by the specification, then they have to be altered so they do.
2.2.6. ONGOING MONITORING
Even once the process is set up and operational, there is still scope for ongoing monitoring
and improvement of the system. Systems like Kaizen offer a means to extend the process
design process over the entire lifetime of the system, ensuring that the process is
constantly being developed and inefficiencies are removed.
2.2.STANDARDS AND CODES
STANDARDS
A technical standard is an established norm or requirement. It is usually a formal document
that establishes uniform engineering or technical criteria, methods, processes and
practices.
CODES
A code is a set of rules and specifications for the correct methods and materials used in a
certain product, building or process. Codes can be approved by local, state or federal
governments and can carry the force of law. The main purpose of codes is to protect the
public by setting up the minimum acceptable level of safety for buildings, products and
processes.
2.2.1. AMERICAN PETROLEUM INSTITUTE (API)
The American Petroleum Institute (API) maintains more than 500 documents that apply to
many segments of the oil and gas industry - from drill bits to environmental protection. API
standards advocate proven, sound engineering and operating practices and safe,
interchangeable equipment and materials.
API standards include manuals, standards, specifications, recommended practices,
bulletins, guidelines and technical reports.
2.2.2. ASTM INTERNATIONAL
1 5
ASTM International is comprised of more than 132 technical standards writing committees
and publishes over 9,100 standard specifications, tests, practices, guides, and definitions
relating to materials, products, systems, and services. Topics range from chemical products
and fossil fuels to forensic sciences and medical devices.
2.2.3. INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO)
ISO, the International Organization for Standardization, is a nonprofit organization that
develops and publishes standards of virtually every possible sort, ranging from standards
for information technology to fluid dynamics and nuclear energy. Headquartered in Geneva,
Switzerland, ISO is composed of 162 members, each one the sole representative for their
home country
2.2.4. NFPA STANDARDS AND CODES
NFPA develops, publishes, and disseminates more than 300 consensus codes and
standards intended to minimize the possibility and effects of fire and other risks. Virtually
every building, process, service, design, and installation in society today is affected by
NFPA documents.
2.2.5. OSHA STANDARDS
The Occupational Safety and Health Administration (OSHA) regulates worker safety in the
United States and its territories. Health and safety standards are contained in Title 29 of the
Code of Federal Regulations (29 CFR), and are available online. In the OSHA CFR, there
are several different sections (also called parts) of safety and health standards (also called
regulations) applicable to the various types of workplaces regulated by this agency. There
are OSHA standards (Part 1903) regulating OSHA inspections, citations, and penalties for
all affected workplaces, as well as specific standards for reporting and recording OSHA-
recordable injuries and illnesses(Part 1904) that apply to all affected employers who do not
fall into the exemptions for size or low-risk industries (although they must still comply with
all other applicable OSHA regulations).
2.2.6. ELECTRICAL STANDARDS AND APPROVED CODES OF PRACTICE
1 6
There are some commonly used electrical standards and approved codes of practice
shown in annexure. Additional standards and codes of practice would generally be needed
to satisfy a specific application - it is the responsibility of the specified to select and apply
these. You should ensure that the standard you use is the current one.
The standards are organized into a number of topic areas and are ordered with the lowest
number at the top of each table:
Electrical and Power
Electrical Appliances
Electromagnetic Compatibility
Flammable Atmospheres
Machinery
2.3.Introduction with Unit Operation & Unit Operation in PPL Plants
The company operates the largest gas field at Sui and five others at Kandhkot, Hala,
Chachar, Adhi, and Mazarani. It holds working interest in 12 partner operated fields
including Qadirpur, Sawan, Nashpa, Latif etc. PPL-operated fields produce an average of
one bcfd which is sold to the company's main clients: Wapda, SSGC and SNGPL.
2.3.1. SUI GAS FIELD (PPL SHARE 100%)
Since its discovery in 1952, the Sui Gas Field remains an important source of gas
supply,meeting substantial part of gas demand of the country. Reservoirs in SUI are SUL,
SML, HRL, Pab formation. SUL has no H2S, less CO2 so it undergoes dehydration only.
Pab has a lot of H2S and CO2. H2S is upto 1000-1500 ppm. CO2 is maximum 7 mole%. As
per sales gas requirement, H2S should be till 4 ppm and CO2 should be 3 mole% so it
undergoes gas sweetening as well.
SUI Plant is divided into three parts.
SUI Compression Station
HRL (small plant )
1 7
Capacity: 30 MMscfd
SCFGCS (large plant )
Capacity: 900-950 MMscfd
SUI Purification Plant
Capacity: 900-950 MMscfd
SUI Dehydration Plant
Capacity: 200-300 MMscfd
2.3.2. KANDHKOT GAS FIELD (PPL SHARE 100%)
Gas from Kandhkot Field is mainly supplied to WAPDA and SNGPL for use at Guddu
Thermal Power Station. A nominal quantity of gas is also supplied to SSGCL for Kandhkot
Town.
The unit operations at Kandhkot include compression and dehydration at Compression
Station and Dehydration Plant.
2.3.3. ADHI FIELD (PPL SHARE 39%)
PPL / OGDCL / POL JOINT VENTURE
Adhi has 3 plants. Plant 1 called LPG/NGL recovery plant was established in 1991. Plant 2
called EPL (Early Production Liquid) was established in 2006 and plant 3 will be established
in 2014. Plant 1 and 2 requires no sweetening. Thus, plant 1 which is the main plant
undergoes gas dehydration only and recovers LPG/NGL and plant 2 has a capacity of 5000
MMscfd.
A total of eleven wells are in production at Adhi. Two wells are producing crude oil from
Sakesar formation and the remaining are Tobra / Khewra wells producing oil, NGL and gas.
LPG is also extracted from the Plant feed and sold to customers.
2.3.4. MAZARANI GAS FIELD (PPL SHARE 87.5%)
1 8
PPL / GHPL JOINT VENTURE
Mazarani gas field comprises of Gas Processing Plant and an 8” dia. 75 Km long gas
transmission pipeline for injection of Mazarani gas into SSGCL's Indus Right bank
transmission system.
A total of four wells have been drilled to-date in Mazarani Field. Out of these four wells,
Well Maz-1 was plugged and abandoned whileMaz-2(L), Maz-3(L) and Maz-4(L) have been
completed in Laki formation and are in production.
The unit operations and unit processes at Mazarani include
Gas compression
Amine unit
Dehydration
2.3.5. CHACHAR GAS FIELD (PPL SHARE 75%)
PPL / GHPL JOINT VENTURE
The field is in the East of Kandhkot Gas Field.A total of four wells have been drilled in
Chachar Field, of which Chachar 1 and 2 are in normal operation and Chachar-4 is
intermittently in operation due to water loading, while Chachar-3 is completely shut-in due
to high water production.Cathodic Protection System has been installed and commissioned
at Chachar-1, 2, 3 and 4 wells.
The unit operations and unit processes at Chachar include
Gas compression
Amine unit
Dehydration
2.3.6. HALA GAS FIELD (PPL SHARE 65%)
1 9
MGCL / PPL JOINT VENTURE
PPL had drilled first exploratory well Adam X-1 in Hala Block during 2007 which resulted in
a gas / condensate discovery. Plant is operating at reduced rate due to change in reservoir
behavior; water and sand production started from Upper Basal formation. For optimizing the
production and to mitigate sand problem, a sand trap was installed in July 2011 and it has
been recently de-commissioned in view of well behavior. Hala is basically LPG recovery
field.
2 0
PREPARATION OF PROCESS DESIGN DOCUMENTS
3.1. The Block Flow Diagrams (BFDs)
BFD shows overall processing picture of a chemical complex, flow of raw materials and
products may be included on a BFD.
BFD can either be
Block Flow Process Diagram
Block Flow Plant Diagram
BLOCK FLOW PROCESS DIAGRAM
Block Flow Process Diagram is similar to sketches in material and energy balances.
BLOCK FLOW PLANT DIAGRAM
Block Flow Plant Diagram gives a general view of a large complex plant.
3.2. The Process Flow Diagrams (PFDs)
PFD (or SFD- System Flow Diagram) shows relationship between major components in a
system. A PFD also tabulates process design values for the components in different
operating modes, typical minimum and maximum values. A PFD shouldn’t show minor
components, the piping systems, piping ratings and designations.
3.3. Heat and Material Balance (H&MB)
Heat and mass balance is a document produced by process design engineers while
designing a process plant. A heat and mass balance sheet represents every process
stream on the corresponding PFD in terms of the process conditions.
2 1
3.4. The Piping and Instrumentation Diagrams (P&IDs)
P&ID displays ‘the interconnection of process equipment and the instrumentation used to
control the process’.
3.5. The Plot Plans
Plan or map drawn looking down on plant (drawn to scale with all major equipment
identified).
3.6. Process Simulation
Process simulation is a model-based representation of chemical, physical, biological, and
other technical processes and unit operations in software. The software has to solve
the mass and energy balance to find a stable operating point. The goal of a process
simulation is to find optimal conditions for an examined process. This is essentially
an optimization problem which has to be solved in an iterative process.
.They include CAMCAD, HYSYS, Aspen Plus ,Ascend , Hysim ,distil simu, MASSBAL etc.
I practiced HYSYS for the certain Oil and Gas processing unit and it helped me to get
familiar with simulation environment and its working tools.
2 2
PROCESS DESIGN CALCULATION OF PIPELINES SYSTEM & MAJOR PROCESS UNITS
4.1. Introduction with Transient Flow Regimes
Slug flow can pose serious problems to the designer and operator of two-phase flow
systems. Prediction of slug characteristics is essential for the optimal, efficient and safe and
economical feasible design and operation of two-phase gas-liquid slug flow systems.
Some operations causing slugging include slugging caused by pigging, large pressure
impacts, pigging problems, fatigue, high frictional pressure loss, end of production when low
flow rates
SLUG PHENOMENA
When liquid and gas are flowing together in a pipeline, the liquid can form slugs that are
divided by gas pockets. The formation of liquid slugs can be caused by a variety of
mechanisms:
1. Hydrodynamic effects (surface waves)
2. Terrain effects (dip in pipe layout)
1. Hydrodynamic effects
Hydrodynamic or normal slug flow occurs at moderate gas and liquid flow rates, and hence
is commonly encountered in multiphase pipelines. Hydrodynamics slug-flow is
characterized by a series of Taylor bubbles (gas pockets) separated by liquid slugs. In
upward flow, the Taylor bubbles are symmetrical.
2. Terrain effects
Terrain-induced slugging and riser-induced slugging are both classified as severe slugging,
and characterized by liquid accumulation at low points. The gas upstream is compressed
until it overcomes the gravitational head of the liquid; thereby creating a long liquid slug that
is pushed in front of the expanding gas upstream.It is worth noticing that terrain slugging
occurs for relatively low liquid and gas flow rates.
2 3
4.2. Hydraulic Calculations of Process Piping
4.2.1. HYDRAULIC DESIGN
1. Hydraulic balance
2. Pressure drop of piping
3. Pipe inside diameter
4. Pressure drop hand calculation by funning equation
5. Line sizing
6. Calculation of Le
7. Pressure drop of others
8. Pressure drop and flow control by control valve
9. Max suction pressure and max shut-off pressure
10.NPSH
11.HFD (hydraulic flow diagram)
12.Hydraulic hand calculation
4.3. Separators
Separators can be vertical, spherical, or horizontal, and typically employ a series of baffles
to separate the gas from the liquid hydrocarbons. A horizontal separator is used when the
gas-to-liquid hydrocarbons ratio is large; a vertical separator is used when the gas-to-liquid
hydrocarbon ratio is small; and a spherical separator is used when the gas-to-liquid
hydrocarbon ratio is in the intermediate range. When wellhead pressures are high, a series
of separators may be operated at sequentially reduced pressures. Three principles used to
achieve physical separation of gas and liquids or solids are momentum, gravity settling, and
coalescing. The purpose of separators is to split the flow into desirable fractions.
Gravity Separation
The followings are formulas for Stokes Law, Intermediate and Newton's
2 4
4.3.1. SPECIFYING SEPARATORS
Separator designers need to know pressure, temperature, flow rates, and physical
properties of the streams as well as the degree of separation required. It is also prudent to
define if these conditions all occur at the same time or if there are only certain combinations
that can exist at any time. If known, the type and amount of liquid should also be given, and
whether it is mist, free liquid, or slugs.
4.3.2. DESIGN APPROACH
Calculate gas and liquid density. Calculate mass flow rate. Calculate particle diameter. Calculate drag coefficient (C’) (appendix A) Calculate Reynolds no. On the basis of Reynolds use Stokes’ law, Intermediate law, Newton’s law . Calculate terminal velocity and gas flow Assume diameter based, calculate length. Now based on L/D ratio check the feasibility of the separator. See Annexure G
2 5
4.4.Heat exchangers
A heat exchanger is a specialized device that assists in the transfer of heat from one fluid to
the other. In the most efficient heat exchangers, the surface area of the wall between the
fluids is maximized while simultaneously minimizing the fluid flow resistance.
There are two major different designs of heat exchangers: shell and tube, and plate heat
exchanger. The most typical type of heat exchanger is the shell and tube design while plate
heat exchanger is typically more efficient than the shell and tube design.
SHELL & TUBE EXCHANGER
A shell and tube heat exchanger is a class of heat exchanger designs. It is the most
common type of heat exchanger in oil refineries and other large chemical processes, and is
suited for higher-pressure applications. It consists of a tube bundle enclosed in a cylindrical
casing called a shell. One fluid runs through the tubes, and another fluid flows over the
tubes (through the shell) to transfer heat between the two fluids.
There are two basic types of shell-and-tube exchangers. The first is the fixed tube sheet
unit, in which both tube sheets are fastened to the shell and the tube bundle is not
removable. The second type of shell-and-tube unit has one restrained tube sheet, called the
stationary tube sheet, located at the channel end. Differential expansion problems are
avoided by use of a freely riding floating tube sheet at the other end or the use of U tubes.
Shell-and-tube exchangers are designed and fabricated according to the standards of the
Tubular Exchanger Manufacturers Association (TEMA).
4.4.2. DESIGN GUIDELINES
References: Hewitt et al “Process Heat Transfer” p267, Kern “Process Heat Transfer”
Chapter 7, p127 and Perry Section 11 p11-0 to p11-19
Definitions
Heat exchanger configurations are defined by the numbers and letters established by the
Tubular Exchanger Manufacturers Association (TEMA). Refer to Appendix V for full details.
For example: A heat exchanger with a single pass shell and multi-pass tube is defined as a
2 6
1-2 unit. For a fixed tube-sheet exchanger with removable channel and cover, bonnet type
rear head, one-pass shell 591mm (231/4in) inside diameter with 4.9m (16ft) tubes is defined
SIZE 23-192 TYPE AEL.
Tube Diameter
The most common sizes used are 3/4"od and 1"od
Use smallest diameter for greater heat transfer area with a normal minimum of 3/4"od tube
due to cleaning considerations and vibration.1/2"od tubes can be used on shorter tube
lengths say < 4ft.
The wall thickness is defined by the Birmingham wire gage (BWG) details are given in
Appendix XI (Kern Table 10)
Tube Number and Length
Select the number of tubes per tube side pass to give optimum velocity 3-5 ft/s (0.9-1.52
m/s) for liquids and reasonable gas velocities are 50-100 ft/s(15-30 m/s).
If the velocity cannot be achieved in a single pass consider increasing the number of
passes.
Tube length is determined by heat transfer required subject to plant layout and pressure
drop constraints. To meet the design pressure drop constraints may require an increase in
the number of tubes and/or a reduction in tube length.
Long tube lengths with few tubes may give rise to shell side distribution problems.
Tube Layout, Pitch and Clearance
Definitions and Nomenclature
B baffle spacing (pitch)
PT tube pitch
C clearance
do tube outside diameter
2 7
D shell inside diameter
Tube pitch is defined as
PT = do + C
Triangular pattern provides a more robust tube sheet construction.
Square pattern simplifies cleaning and has a lower shell side pressure drop.
Typical dimensional arrangements are shown below, all dimensions in inches.
Tube od (in) Square Pitch (in) Triangular Pitch (in)
5/8 7/8 Note 1 25/32 Note 1
3/4 1 Note 2 15/16 or 1 Note 12
1 11/4 11/4
11/4 19/16 19/16
11/2 17/8 17/8
Note 1 for shell ≤12” pitch (square) 13/16
Note 2 for shell ≤12” pitch (square) 15/16
Table above uses minimum pitch 1.25 times tube diameter i.e. clearance of 0.25 times tube
diameter.
Smallest pitch in triangular 30º layout for turbulent / laminar flow in clean service.
For 90º or 45º layout allow 6.4mm clearance for ¾ tubes for ease of cleaning.
Shell Diameter
The design process is to fit the number of tubes into a suitable shell to achieve the desired
shell side velocity 4ft/s(1.219m/s) subject to pressure drop constraints. Most efficient
conditions for heat transfer is to have the maximum number of tubes possible in the shell to
maximize turbulence.
Preferred tube length to shell diameter ratio is in the range 5 to 10.
Tube count data are given in Perry Table 11-3 where the following criteria have been used
2 8
1) Tubes have been eliminated to provide entrance area for a nozzle equal to 0.2 times
shell diameter
2) Tube layouts are symmetrical about both the horizontal and vertical axes
3) Distance from tube od to centerline of pass partition 7.9mm (5/16) for shell id <559mm
(22in) and 9.5mm (3/8) for larger shells.
Heat Transfer Area
Using the maximum number of tubes, subject to adequate provision for inlet nozzle, for a
given shell size will ensure optimum shell side heat transfer in minimizing tube bundle
bypassing.
The heat transfer area required design margin is then achieved by adjusting the tube length
subject to economic considerations. On low cost tube materials it may be more economical
to use standard lengths and accept the increased design margin.
It is a common practice to reduce the number of tubes to below the maximum allowed
particularly with expensive tube material. In these situations the mechanical design must
ensure suitable provision of rods, bar baffles, spacers, baffles to minimize bypassing and to
ensure mechanical strength.
Baffle Design – Definitions
Shellside cross flow area as is given by
Where
D shell i.d.
B baffle spacing
C clearance between tubes
PT tube pitch
Minimum spacing (pitch)
2 9
Segmental baffles normally should not be closerthan 1/5th of shell diameter(ID) or
50.8mm(2in) whichever is greater.
Maximum spacing (pitch)
Spacing does not normally exceed the shell diameter.
Tube support plate spacing determined by mechanicalconsiderations e.g. strength and
vibration.
Maximum spacing is given by
Most failures occur when unsupported tube length greater than 80% TEMA maximum due
to designer trying to limit shell
side pressure drop. Refer to attachments.
Baffle cut
Baffle cuts can vary between 15% and 45% and are expressed as ratio of segment opening
height to shell inside diameter. The upper limit ensures every pair of baffles will support
each tube.
Kern shell side pressure drop correlations are based on 25% cut which is standard for liquid
on shell side When steam or vapour is on the shell side 33% cut is used.
Baffle pitch and not the baffle cut determines the effective velocity of the shell side fluid and
hence has the greatest influence on shell side pressure drop.
Horizontal shell side condensation require segmental baffles with cut to create side to side
flow.
To achieve good vapour distribution the vapour velocity should be as high as possible
consistent with satisfying pressure drop constraints and to space the baffles accordingly.
Baffle clearances
3 0
The edge distance between the outer tube limit (OTL) and the baffle diameter has to be
sufficient to prevent tube
breakthrough due to vibration. For example fixed tube-sheet clearances are shown below.
Refer to Perry p11-11 for floating head clearances.
Shell inside diameter mm (in) Clearance shell id and OTL mm (in)
254(10) to 610(24) 11(17/16)
≥ 635(25) 13(1/2)
Tube-sheet Layout (Tube Count)(Ref 4, page 577)
Bundle diameterDb can be estimated using constants shown:
Where do tube o.d.
Nt number of tubes
Triangular Pitch pt= 1.25 do
Number
Passes
1 2 4 6 8
K1 0.319 0.249 0.175 0.0743 0.0365
n 2.142 2.207 2.285 2.499 2.675
Square Pitch pt= 1.25 do
Number
Passes
1 2 4 6 8
K1 0.215 0.156 0.158 0.0402 0.0331
n 2.207 2.291 2.263 2.617 2.643
Fouling Considerations
Typical fouling coefficients are shown inAppendix VII. It can be shown that the design
margin achieved by applying the combined fouling film coefficient is given by:
3 1
Where AC is the clean HTA , Af is the dirty or design HTA and UC is the clean OHTC.
Results for Typical Fouling Coefficients (British Units)
Fouling Resistances Fouling Coefficients Clean
OHTC
Design
MarginInside Outside Inside Outside Combined
0.002 0.001 500 1000 333 50 1.15
0.002 0.001 500 1000 333 100 1.3
0.002 0.002 500 500 250 50 1.2
0.001 0.001 1000 1000 500 50 1.1
Corrosion Fouling
Heavy corrosion can dramatically reduce the thermal performance of the heat exchanger.
Corrosion fouling is dependent on the material of construction selection and it should be
possible to eliminate altogether with the right choice. However if economics determine that
some corrosion is acceptable and no data is available from past experience an allowance of
1/16in (1.59 mm) is commonly applied.
Design Margin
The design margin to be applied to the design is based onthe confidence level the designer
has regarding the specific application and the future requirements for multipurpose
applications. Design of condensers for multipurpose use, where a wide possible variation in
flow conditions can exist, provides a particular problem in this regard.
It is standard practice to apply a design margin of 15% to the design (dirty) heat transfer
area with the result that this is applied to the design margin resulting fromthe application of
the fouling film coefficients discussed previously giving an added safety factor.
Pressure Drop
For process design using a simulation the following preliminary conservative estimates are
given for pressure drops due to friction. Note an additional pressure change occurs if the
exchanger is placed vertically.
3 2
Initial Process Design Pressure Drop Estimates
Process Description Pressure Drop (psi) Pressure (kPa)
Liquid streams with no
phase change
10 70
Vapor streams with no
phase change
2 14
Condensing streams 2 14
Boiling streams 1 7
AIR COOLED HEAT EXCHANGER
The Air-cooled heat exchanger is a device for rejecting heat from a fluid or gas directly to
ambient air. When cooling both fluids and gases, there are two sources readily available,
with a relatively low cost, to transfer heat to air and water.
4.4.3. DESIGN GUIDELINES
The basic heat transfer relationships that exist for shell and tube exchangers also apply to
the design of an air-cooled heat exchanger. However, there are more parameters to be
considered in the design of an air-cooled exchanger.
Since the air-cooled heat exchanger is exposed to changing climatic conditions, problems
of control of the air cooler become relevant. A decision must be made as to what the actual
ambient air temperature to be used for the design.
Some of the governing factors in the design of the air cooler are:
Tube diameter
Tube length
Fin height
Number of tube rows
Number of passes
Face area
Horse power availability
Plot area
3 3
Since there are many variables, normally there many solutions, however the designer
attempts to find the optimum economic design given these factors.
4.5.Towers
Towers are used for fractionation. Fractionation is a unit operation utilized to separate
mixtures into individual products. Fractionation involves separating components by relative
volatility (α). The difficulty of a separation is directly related to the relative volatility of the
components and the required purity of the product streams.
DE-ETHANIZER
De-ethanizer is the distillation column in a gas processing plant where ethane is separated
from a natural gas or natural gas liquids. It is separated from the natural gas liquids to
stabilize the liquid petroleum gas. The ethane is returned to the gas stream.
DE-BUTANIZER
A debutanizer is a type of fractional distillation column used to separate butane from natural
gas during the refining process. Fractional distillation, as occurs in a debutanizer, is the
separation of a fraction — a set of compounds that have a boiling point within a given range
— from the rest of the mixture.
STRIPPING TOWERS
VOCs, once in the ground, can be present for a very long time. Even when they reach an
aquifer, the speed of flow is often measured in just a few minutes per year.
Contamination may be found by chance in springs and wells or when dewatering
construction sites. Or it may be surveyed and quantified when pollution, recent or long past,
is known to have occurred. The necessity for remediation is most immediate where a spring
or well is needed for use, or where excavation water is too polluted to be disposed of
without treatment. Stripping by packed tower aeration offers an effective and economical
3 4
approach to many VOC contamination scenarios and Forbes has considerable experience
in the design and fabrication of stripping installations.
4.5.1. DESIGN
In order to determine the design parameters for a fractionation problem, the following
method is recommended:
1. Establish feed composition, flow rate, temperature, and pressure.
2. Make product splits for the column and establish condenser temperature and column
pressure. From column pressure, calculate the reboiler temperature.
3. Calculate minimum number of theoretical stages from the Fenske equation from Eq 19-3
illustrated in the GPSA manual
4. Calculate minimum reflux rate from the Underwood equations from Eq 19-7 and 19-8
illustrated in the GPSA manual.
5. Obtain theoretical stages/operating reflux relation from Fig. 19-7 illustrated in the GPSA
manual.
6. Adjust actual reflux for feed vaporization if necessary from Eq 19-9 and 19-10 illustrated
in the GPSA manual.
4.6.Pumps
The most common types of pumps used in gas processing plants are centrifugal and
positive displacement. Occasionally regenerative turbine pumps, axial-flow pumps, and
ejectors are used.
Modern practice is to use centrifugal rather than positive displacement pumps where
possible because they are usually less costly, require less maintenance, and less space.
POSITIVE DISPLACEMENT PUMPS
Positive displacement (PD) pumps work by allowing a fluid to flow into some enclosed
cavity from a low-pressure source, trapping the fluid, and then forcing it out into a high-
pressure receiver by decreasing the volume of the cavity. Some examples of PD pumps
3 5
are: fuel and oil pump in most automobiles, the pumps on most hydraulic systems, and the
heart of most animals.
Some general types of the positive displacement pump areas below:
a) Reciprocating Pump
Reciprocating pumps create and displace a volume of liquid, their “displacement volumes”,
by action of a reciprocating element. Liquid discharge pressure is limited only by strength of
structural parts. A pressure relief valve and a discharge check valve are normally required
for reciprocating pumps.
Reciprocating pumps can be further classified into three types of pump as below,
i) Piston Pumps
ii) Packed Plunger Pumps
iii) Diaphragm Pumps
b) Rotary Pump
Rotary pumps function with close clearances such that a fixed volume of liquid is displaced
with each revolution of the internal element. Rotary pumps include:
i) Gear Pump
ii) Lobe Pump
iii) Vane Pump
iv) Screw Pump
CENTRIFUGAL PUMPS
Centrifugal pumps are dynamic pumps. A centrifugal pump raises the pressure of the liquid
by giving it a high kinetic energy and then converts it into pressure energy before the fluid
exits the pump. It normally consists of an impeller (a wheel with blades), and some form of
housing with a central inlet and a peripheral outlet. The impeller is mounted on a rotating
shaft and enclosed in a stationary casing. Casings are generally of two types: volute and
circular. The impeller design and the shape of the casing determine how liquid is
accelerated though the pump.
Centrifugal pumps are used in more industrial applications than any other kind of pump.
This is primarily because these pumps offer low initial and upkeep costs. Traditionally these
pumps have been limited to low-pressure-head applications, but modern pump designs
3 6
have overcome this problem unless very high pressures are required. The single-stage,
horizontal, overhung, centrifugal pump is by far the most commonly type used in the
chemical process industry.
SELECTION OF PUMP
Basically, pump selection is made on the flow rate and head requirement and with other
process considerations, such as material of the construction pumps for the corrosive
chemical service or for the fluid with presence solids in the stream.
PERFORMANCE CURVE
Operating characteristics of centrifugal pumps are expressed in a pump curve. Depending
on impeller design, pump curves may be "drooping," "flat," or "steep." Pumps with drooping
curves tend to have the highest efficiency but may be undesirable because it is possible for
them to operate at either of two flow rates at the same head. The influence of impeller
design on pump curves is discussed in detail in Hydraulic Institute Standards.
4.6.1. DESIGN
Process Requirements Parameters
In designing the pump, the knowledge of the effect of parameters; such as pump capacity,
NPSH, pumping maximum temperature, specific gravity, fluid viscosity, fluid solid content,
and the other process requirements are very important. All of these parameters will affect
the selection and design of the pump which will affect the performance of the pump in the
process.
Flow Rate
Pump capacity is a parameter plays an important role when selecting the pump.
Capacity means the flow rate with which liquid is moved or pushed by the pump to the
desired point in the process. It is commonly measured in either gallon per minute (gal/min)
or cubic meters per hour (m3/hr). The capacity usually changes with the changes in
operation of the process. A minimum required flow rate need to be specified, this is
important to determining if a minimum flow bypass is required for the selected pump to
avoid pump overheating and mechanical damage.
3 7
NPSHNPSH as a measure to prevent liquid vaporization or called cavitation of pump. Net Positive
Suction Head (NPSH) is the total head at the suction flange of the pump less the vapor
pressure converted to fluid column height of the liquid. The design engineer should always
remember that pumps can pump only liquids, not vapors because when a liquid vaporizes
its volume increases greatly. For example: 1ft
3 of water it will vaporize to produce 1700ft3 of steam. This will cause the rise in
temperature and pressure drop in the fluid and pump will stop functioning because it has
not sufficient suction pressure present.
Design TemperaturePumping maximum temperatures is important in deciding pump construction style and
pump cooling and mechanical seal requirements. The minimum operating temperature is to
ensure that the material has adequate impact strength.
Specific GravitySpecific gravity is parameter determines the pump head required to produce a desired
pressure increase. For pumps with limited head capability such as centrifugal pumps, it
affects pressure rise capability. Pump power requirements are also affected by specific
gravity.
Viscosity
Viscosity is important in the selection of pump type and has a significant effect on
centrifugal pump performance. Minimum values of viscosity are important in determining
rotary pump (positive displacement pump) performance, while maximum viscosity is
important in determining debits to centrifugal pump performance.
AbrasivesFluid solid content will affect the pump design. It affected the aspects of the design for the
flow characteristic, consideration design of erosion resistance, flow passage size, impeller
style, peripheral speed, design features to disintegrate large particles, and shaft sealing
design. This parameter has to be added in the data sheet for design.
FlexibilityOther process requirement such as flexibility for expansion should be consider as well.
3 8
This is important for future capacity expansion; it helps to minimize the cost of expansion
because to replace the pump will be a large sum of money. Working capacity of pump
should always be design for more than 20% extra design capacity.
4.7.Compressors
RECIPROCATING COMPRESSORS
Reciprocating compressor ratings vary from fractional to more than 40,000 hp per unit.
Pressures range from low vacuum at suction to 30,000 psi and higher at discharge for
special process compressors.
Reciprocating compressors are furnished either single-stage or multi-stage. The number of
stages is determined by the overall compression ratio. The compression ratio per stage
(and valve life) is generally limited by the discharge temperature and usually does not
exceed 4, although small-sized units (intermittent duty) are furnished with a compression
ratio as high as 8.
CENTRIFUGAL COMPRESSORS
A multi-wheel (multi-stage) centrifugal compressor is normally considered for inlet volumes
between 500 and 200,000 inlet acfm. A single-wheel (single stage) compressor would
normally have application between 100 and 150,000 inlet acfm. A multiwheel compressor
can be thought of as a series of single wheel compressors contained in a single casing.
Most centrifugal compressors operate at speeds of 3,000 rpm or higher, a limiting factor
being impeller stress considerations as well as velocity limitation of 0.8 to 0.85 Mach
number at the impeller tip and eye. Recent advances in machine design have resulted in
production of some units running at speeds in excess of 40,000 rpm.
Centrifugal compressors are usually driven by electric motors, steam or gas turbines (with
or without speed-increasing gears), or turbo expanders.
4.7.1. DESIGN
There is an overlap of centrifugal and reciprocating compressors on the low end of the flow
range according to Fig-13-3 titled “Compressor Coverage Chart”, illustrated in the GPSA
3 9
manual. The selection of an appropriate compressor is based upon it. This figure covers the
normal range of operation for compressors of the commercially available types. Using this
chart it is inferred that Compressor K-103, based on an inflow of 92.73 ACFM and
discharge pressure of 1175 psig, can be designed either as a single-stage Centrifugal
pump or a multi-stage Reciprocating pump. See Annexure H.
4.8.Storage
The selection section contains the explanation for the suitability of types of tank system
used in processing industries, which are based on the environmental regulations, location,
and process materials involved.
4.8.1. GENERAL DESIGN CONSIDERATIONS
Storage vessels containing organic and non organic liquids and vapors can be found in
many industries, including;
(1) Petroleum producing and refining,
(2) Petrochemical and chemical manufacturing,
(3) Bulk storage and transfer operations, and
(4) Other industries consuming or producing liquids and vapors.
Liquids and vapors in the bulk storage and transfer operations can be organic or
hydrocarbon in nature. All those chemical should keep in the right storage tank. Design
and safety concern has come to a great concern as reported case of fires and explosion for
the storage tank has been increasing over the years and these accident cause injuries and
fatalities.
LPG STORAGE TANK
The two main forms of LPG are commercial butane and commercial propane. LPG may be
liquefied by moderately increasing the pressure or by reducing the temperature.
4 0
Refrigerated storage is used by gas suppliers to store large volumes of LPG. The main form
of LPG storage is in special tanks known as 'pressure tanks'. Commonly these pressure
tanks are termed 'bulk tanks' or LPG Bullets. because LPG has a high coefficient of
expansion in its liquid phase, the tanks are never completely filled with liquid (tanks are
filled to approximately 85% of their water capacity), the remaining space being taken up
with vapor (often referred to as the vapor space) to facilitate expansion without allowing the
liquid to become 100% full (often known as hydraulically full).
Most LPG storage tanks in standby-plant service are steel, non-refrigerated pressure
vessels. Tanks are available in many sizes for both aboveground and underground service.
New propane tanks are built to ASME standards and are designed for at least 250 psig
working pressure. Common tank sizes and approximate dimensions are shown in the chart
below. Larger industrial and commercial applications generally use 18,000 gallon and larger
tanks.
Technical SpecificationStandard Design As per ASME sec VIII Div 1 Pressure
Vessel Code
Pressure Design 18.0 bar
Design Temperature (atm) range -20 / +50 °C
Hydraulic Test Pressure 25.0 bar
Joints efficiency 0.85
Radiographs 100 %
Manhole 1
Flanging # ASA 300
Gates 8
Thickness 6 mm to 50 mm
Diameter 600 mm to 3000 mm
Length Up to 18 Meters Long
Weight 3000 To 80000 Kg
Typical sizes available2, 4 & 6 tons
8 & 10, Tons
4 1
12 & 15 Tons
18 & 20 Tons
26 & 30 Ton
36 & 40 Tons
NGL STORAGE TANKS
Natural gas processing plants remove NGLs in the natural gas stream due to liquid and Btu
content. The very low temperatures or high pressures required to keep natural gas in its
liquid state for storage.
DIESEL STORAGE TANKS
There are no specific legal requirements on how to store diesel or the quantity allowed
either in workplaces or domestic premises. It is not, from a health and safety point of view,
a particularly hazardous substance within the meaning of the Dangerous Substances and
Explosive Atmospheres Regulations 2002 - its vapor flash point is too high. This means that
its vapor will not ignite at normal room temperatures.
Diesel does not require a Location Test Certificate or an approved handler.
When stored in a bulk storage tank of more than 5,000 litres, a Stationary Container Test
Certificate is required. This is also the case if the diesel is used in connection with an oil
burning installation or an internal combustion engine, such as a generator. In this case, the
threshold could be as low as 60 litres. There are exceptions where the diesel is used in a
domestic oil burning installation.
Diesel may be kept in a store room in a building, but the store room must have a fire
resistance rating and the quantities allowed are limited, as is the package size.
CONCLUSION
4 2
Training at Pakistan Petroleum Ltd. is really a true learning experience. It has just not
taught the utilization of bookish knowledge into practical field but also the ethics of
professional life. This internship would remain the part of magnificence memories for the
reason of PPL’s hospitality & efforts of my seniors to teach their activities. It is expected that
this technical guidance & professional knowledge would be helpful in my future studies.
4 3
REFERENCES
http://www.ehow.com/list_7472499_fundamentals-process-design.html
http://www.msoe.edu/library/resources/standards/index.shtml
http://www.ihs.com/products/industry-standards/organizations/api/index.aspx
http://www.techstreet.com/info/astm.tmpl
http://www.nfpa.org/categoryList.asp?categoryID=124&URL=Codes%20&%20Standards
http://www.hse.gov.uk/electricity/standards.htm
http://www.osha.net/federal-osha-standards-and-regulations.html
http://oilgasprocessing.com/Gravityseparation.htm
http://www.engineeringtoolbox.com/pfd-process-flow-diagram-d_865.html
Gas Processing Suppliers Association (U.S.) Engineering data book : SI version / published
as a service to the gas processing and related process industries by the Gas Processors
Suppliers Association; compiled and edited in co-operation with the Gas Processors
Association, 12th ed.Tulsa, Oklahoma : Gas Processors suppliers Association, 2004.
Viska Mulyandasari, Heat Exchanger Selection and Sizing (Engineering Design Guideline), KLM Technology Group, Rev 03 November 2010.
R. Mukherjee, Shell-and-tube heat exchangers, Chem. Eng. Progress, Feb 1998.
4 4
ANNEXURES
Annexure A
Electrical standards and approved codes of practice
ELECTRICAL AND POWER
Standard Year Description
BS EN 61439 (many parts) 2009 - 2012 Low-voltage switchgear and controlgear assemblies
BS 5266 Parts 1 to 10 also BS
EN 50172
1999 - 2008 Code of practice for emergency lighting
BS 5424 Parts 2 and 3, also
IEC 60158 part 3
1985 - 1988 Specification for low voltage control gear
BS EN 60422 2008 Monitoring and maintenance guide for mineral insulating oils in
electrical equipment
BS 5839 Parts 1 - 11, also
PD6531:2010
1988 - 2010 Fire detection & alarm systems for buildings
BS EN 60079-30-2 2007 Electric surface heating
BS 6423 1983 Code of practice for maintenance of electrical switchgear and
controlgear for voltages up to and including 1 kV
BS 6626 2010 Code of practice for maintenance of electrical switchgear and
controlgear for voltages above l kV and up to and including 36 kV
BS EN 62305, 4 parts 2006-2011 Code of practice for protection of structures against lightning
BS 7375 2010 Code of practice for distribution of electricity on construction and
building sites
BS 7430 1998 Code of practice for earthing
BS 7671 2008 - 2011 Requirements for electrical installations. IEE Wiring Regulations.
Seventeenth edition
BS 7909 2008 - 2011 Code of practice for temporary electrical systems for entertainment and
related purposes.
BS EN 50110 Parts 1 and 2 2004 - 2010 Operation of electrical installations
IEC 60479 Parts 1-4, also
PD6519
1994-2005 Guide to effects of current on human beings and livestock.
BS EN 60529 1992 Specification for degrees of protection provided by enclosures (IP
code)
BS EN 60947 Parts 1-8 2001 - 2011 Specification for low voltage switch gear and control gear
ELECTRICAL APPLIANCES
4 5
Standard Year Description
BS 1362 1973 Specification for general purpose fuse links for domestic and similar
purposes (primarily for use in plugs)
BS 1363 Parts 1 -5 1995 - 2008 13 A plugs, socket-outlets and adaptors.
BS EN (IEC) 60309, Parts 1,2,
4
1999 - 2007 Plugs, socket-outlets and couplers for industrial purposes.
BS EN 60320, Parts 1, 2 1999 - 2009 Appliance couplers for household and similar general purposes.
BS EN 60335, Many parts Specification for safety of household and similar electrical appliances
ELECTROMAGNETIC COMPATIBILITY
Standard Year Description
BS EN 61000-6-3,4 2007 - 2011 Electromagnetic compatibility. Generic emission standard.
BS EN 61000-6-1,2 2005 - 2007 Electromagnetic compatibility. Generic immunity standard.
BS EN (IEC) 60801, Part 2 1993 Electromagnetic compatibility for industrial-process measurement and
control equipment. Electrostatic discharge requirements
FLAMMABLE ATMOSPHERES
Standard Year Description
EEMUA 181 1995 Guide to risk based assessments of in-situ large Ex e & Ex n machines
EEMUA 186 1997 A Practitioners handbook – electrical installation & maintenance in
potentially explosive atmospheres
BS EN 1127, Parts 1,2 2007 -2008 Explosive atmospheres. Explosion prevention and protection.
Basic concepts and methodology for mining
PD CLC/TR 50404: 2003 Code of practice for avoidance of hazards due to static electricity.
BS EN 61241 2004, 2005 Electrical apparatus with protection by enclosure for use in the
presence of combustible dusts.
PD CLC/TR 50427 2004 Assessment of inadvertent ignition of flammable atmospheres by radio-
frequency radiation. Guide
BS EN ISO 10497 2004 Testing of valves. Specification for fire type-testing requirements
BS 7535 1992 Guide to the use of electrical apparatus complying with BS 5501 or BS
6941 in the presence of combustible dusts
BS EN 60079, many parts 2004 Electrical apparatus for potentially explosive atmospheres. Replaced
by BS EN 60079, but remains current.
BS EN 60079-6 2007 Explosive atmospheres. Equipment protected by oil immersion "o"
BS EN 60079-2 2007 Explosive atmospheres. Equipment protected by pressurized
enclosures"p"
BS EN 60079-5 2007 Explosive atmospheres. Equipment protected by powder filling "q"
BS EN 60079-1 2007 Explosive atmospheres. Equipment protected by flameproof
enclosures 'd'
BS EN 60079-7 2007 Explosive atmospheres. Equipment protected by increased safety 'e'
BS EN 60079-11 2007 Explosive atmospheres. Equipment protected by intrinsic safety 'i'
4 6
BS EN 60079-22-2 2007 Explosive atmospheres. Gas detection. Selection, installation, use and
maintenance of detectors for flammable gases or oxygen
Energy Institute Model Code
Of Safe Practice, Part 1 (IP1)
2010 Electrical Safety Code
Energy Institute Model Code
Of Safe Practice, Part 15
(IP15)
2005 Area classification code for installations handling flammable fluids
Energy Institute Model Code
Of Safe Practice, Part 21
(IP21)
2002 Guidelines for the control of hazards arising from static electricity
MACHINERY
Standard Year Description
BS EN ISO 13850 2008 Safety of machinery. Emergency stop. Principles for design.
BS EN 953 1997 - 2009 Safety of machinery. Guards. General requirements for the design and
construction of fixed and movable guards
BS EN 13849 2008 Safety of machinery. Safety related parts of control systems. General
principles for design
BS EN 982 1996 -2008 Safety of machinery. Safety requirements for fluid power systems and
their components. Hydraulics
BS EN 983 1996 -2008 Safety of machinery. Safety requirements for fluid power systems and
their components. Pneumatics
BS EN 1037 1996 -2008 Safety of machinery. Prevention of unexpected start-up
BS EN ISO 12100 2010 Safety of machinery. General principles for design. Risk assessment
and risk reduction.
BS EN 1088 2008 Safety of machinery. Interlocking devices associated with guards.
Principles for design and selection.
PD 5304 2005 Safe use of machinery
BS EN 60204 many parts Safety of machinery. Electrical equipment of machines.
BS EN 61069, Parts 1-8 1991-1999 Industrial-process measurement and control. Evaluation of system
properties for the purpose of system assessment.
BS EN 61310, Parts 1,2,3 2008 Safety of machinery. Indication, marking and actuation.
BS EN 61496, 3 parts 2004 - 2008 Safety of machinery. Electro-sensitive protective equipment.
PIAC 1988 Printing industry advisory committee - safety at power operated paper
cutting guillotines
4 7
Annexure B
Block Flow Process Diagram
4 8
Annexure C
Block Flow Plant Diagram
4 9
Annexure D
Process Flow Diagrams (PFDs)
5 0
Annexure E
5 1
Piping and Instrumentation Diagram (P&IDs)
Annexure F
5 2
Plot Plan
5 3
Annexure G
Separator Sizing
Separator Vessel
Gas flow rate 60 MMSCFDGas Specific Gravity 0.75
Gas MW 21.72
Operating pressure 500 psigOperating temperature 100 oF
Compressibility 0.9Viscosity .012 cp
Flowing gas density, dG 2.07 lb/ft3Flowing oil density, dL 31.2
Separator type Horizontal, two-phase
Mass flow, M 39.8 lb/secParticle diameter, Dp 4.92*10-4 ft
C’(Re)2 4738From Fig. 7-4 GPSADrag Coefficient, C’ 1.40
Terminal Velocity, Vt 0.399 ft/sGas flow, Q 19.2 ft3/sAssume Dv 3.5 ft
Vessel length, L 17.5 ft
Diameter Length L/D3.5 17.5 54 15.315 3.82
4.5 13.615 3.0255 12.25 2.45
N.B. L/D ratio for horizontal separator is typically in the range of 2.5-5.
5 4
Annexure H
Compressor Design
5 5
Compressor K-103
Compressor Type Multi-stage
Reciprocating
with inter-cooling
Number of stages 2
Polytropic exponent 1.284
Polytropic efficiency 78.23%
Inlet stream Outlet stream
Stream name 14 16
Vapor fraction 0.9994 1.0000
Temp. (oF) 28.7549 236.25
Pressure (psig) 250 1175
Molar flow (MMSCFd) 2.9197 2.9197
Mass flow (lb/h) 7805.64 7805.6
Molar enthalpy (Btu/lbmole) 38.62 38.62
Overall compression ratio 4.5
Compression ratio of 1st stage 2.12
Compression ratio of 2nd stage 2.14
Discharge temp. of 1st stage 129.6 oF
Discharge pressure of 1st stage 561.2 psi
Suction pressure of 2nd stage 556.2 psi
Intercooler inlet temp. 129.6 oF
Intercooler outlet temp. 125 oF
Intercooler duty 3.16 hp
Total calculated compressor
duty
130.8 hp
Safety margin in compressor
duty for mechanical losses
5%
Total HYSYS compressor duty 135 hp