ROI-S05931-051E 060407

P ASOLINK

N ETWORK

M ANAGEMENT

T ERMINAL

PNMT (Java version)Installation Manual

(WindowsXP)

NEC CorporationCopyright © 2006

ROI-S05931

- i -

Table of Contents

1. Installation Sequence ............................................................................................................................ 1

2. Phone and Modem Options Setting (Standard 19.2Kbps Connection) ............................................ 2

3. Installation of USB Com Port Driver (USB Connection)................................................................... 7

4. Dial-up Setting ..................................................................................................................................... 10

4 SNMP Service Setting ......................................................................................................................... 20

5 PNMT Setup ........................................................................................................................................ 25

6 Launching PNMT................................................................................................................................ 30

ROI-S05931

- 1 -

1. Installation Sequence

Step1: Modem Setting

Standard 19200bps Modem Setting (Phone and Modem Options Setting)

USB Modem Setting (Installation of USB Com Port Driver)

Step2: Dial-up Connection Setting

Step3: SNMP Service Setting

Step4: Pasolink Network Management Terminal (PNMT) Setup

Step5: Launching PNMT

Network Element (NE) other thanPASOLINK NEO

PASOLINK NEO ONLY

ROI-S05931

- 2 -

2. Phone and Modem Options Setting (Standard 19.2Kbps Connection)

This section deals with the use of a Standard 19.2Kbps Modem Dial-up connection. (for non-PASOLINK-NEO network elements). If you wish to use a USB Modem Driver (for PASOLINK-NEO network elements, please refer to 3.”Installation of USB Com Port Driver”, p.7

(1) Click Start | Settings | Control Panel.

(2) Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.

ROI-S05931

- 3 -

(3) Enter your country and area code in the Location Information window. Click [OK].

(4) Verify the Location and Area Code.

ROI-S05931

- 4 -

(5) Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.

(6) Check Don’t detect my modem ... and click [Next] to continue.

ROI-S05931

- 5 -

(7) Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.

(8) Select Selected ports and COM#, then click [Next] to continue.

ROI-S05931

- 6 -

(9) Click [Finish] to complete the new modem installation.

(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].

(11) Please proceed directly to section 4. Dial-up Setting.

ROI-S05931

- 7 -

3. Installation of USB Com Port Driver (USB Connection)

This section deals with installation of a USB Modem Driver (for PASOLINK-NEO network elements) as the dial-up connection. Connect the PNMT computer to the LCT Port of the NE with a standard USB cable.

(1) Select No, not this time and Click [Next].

(2) Select Install from a list or specific location [Advanced] and click on [Next].

ROI-S05931

- 8 -

(3) Insert the USB driver CD-ROM in the computer’s disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].

(4) Click [Continue Anyway] in the Hardware Installation pop-up alert.

ROI-S05931

- 9 -

(5) USB Modem Driver Installation starts.

(6) USB Com Port Driver installation is complete.

ROI-S05931

- 10 -

4. Dial-up Setting

(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.

(2) The Network Connections window appears. Click Create a new connection in the Network Tasks area.

ROI-S05931

- 11 -

(3) The Welcome to the New Connection Wizard window appears. Click [Next].

(4) Select Connect to the network at my workplace and click [Next] to continue.

ROI-S05931

- 12 -

(5) Select Dial-up connection and click [Next] to continue.

(6) Select Modem – USB Modem Driver [COM#] and click [Next] to continue.

NOTE

This screen appears only when a USB Modem Driver has been installed.

ROI-S05931

- 13 -

(7) In the New Connection Wizard window, enter Pnmt in the Company Name field and click [Next] to continue.

(8) Enter any number in the Phone number field and click [Next] to continue.

ROI-S05931

- 14 -

(9) Verify that Pnmt is displayed as the connection. You can also create a shortcut on your desktop if desired. Click [Finish].

(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.

ROI-S05931

- 15 -

(11) Verify that Modem-Standard 19200 bps Modem [COM1] is displayed on the General tab in the Dial-up Connection Properties window. Click [Configure].

(12) In the Modem Configuration window, uncheck all five boxes.

ROI-S05931

- 16 -

(13) Retain the default setting on the Options tab and click the Security tab.

(14) Retain the default setting on the Security tab and click the Networking tab.

ROI-S05931

- 17 -

(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....

(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].

ROI-S05931

- 18 -

(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.

(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].

ROI-S05931

- 19 -

(19) Retain the default setting on the Advanced tab and click [OK].

After activating Windows XP SP2 Before activating Windows XP SP2

ROI-S05931

- 20 -

4 SNMP Service Setting

NOTE

It is necessary to remove SNMP Service or to stop it if it has already been installed.

To Remove SNMP Service:

(1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click Add/Remove Windows Components.

(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ...

ROI-S05931

- 21 -

(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].

(4) Click [Finish] to complete the removal of SNMP Service.

ROI-S05931

- 22 -

To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel

window.

(6) Click Services in the Administrative Tools window.

ROI-S05931

- 23 -

(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu..

(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].

ROI-S05931

- 24 -

(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.

(10) Restart the computer.

ROI-S05931

- 25 -

5 PNMT Setup

NOTE

If PNMT software has already been installed, please uninstall it before you install a new version.

(1) Insert the PNMT Installation CDROM. Open the CDROM folder and double-click setupwin32.exe.

(2) The following window appears until loading is completed.

ROI-S05931

- 26 -

(3) The welcome message window appears. Click [Next].

(4) Specify the directory in which the PNMT is to be installed. Click [Next].

NOTE

The default path is C:\PNMTj. It is not possible to include blank spaces as in “Program Files”.

ROI-S05931

- 27 -

(5) Specify the License.Key file if one is available. Click [Next].

NOTE

If no License Key is available, operation in Trial mode is possible. Simply leave the License Key field blank and proceed.

IMPORTANT: IMMEDIATE IMPORT OF LICENSE

You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.

ROI-S05931

- 28 -

(6) Specify the directory for storing PNMT log files. Click [Next].

NOTE

The default path is <PNMTj Install Directory> when a Stored Directory is not specified. It is not possible to include blank spaces as in “Program Files”.

(7) Click [Install].

ROI-S05931

- 29 -

(8) During installation, this window appears.

(9) Click [Finish] to close the PNMT installation wizard.

ROI-S05931

- 30 -

6 Launching PNMT

(1) Click Start | Programs |PNMTj |PNMT to start the application.

(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).

ROI-S05931

- 31 -

(3) Enter User name and Password, and Select the Connection Entry.

After installation of the PNMT, the initial password will be:-

User name: admin

Password: (There is no initial password. Just press Enter.

A password can then be set.)

Connection: Select Dial-up and Pnmt entry.

NOTE

If another application is using the SNMP Port, application initialization will not be possible, the application will shut down, and the following message will appear.