H Y D R O D R A I NH Y D R O D R A I NDRAINAGE
MEDIUMS FOR
HORIZONTAL
AND VERTICAL
APPLICATIONS
®®
®
W A T E R M A N A G E M E N T
H Y D R O D R A I N ® P R O D U C T
Water management is a critical
issue in the design and
construction of a structure.
Without proper drainage severe
structural damage could occur.
In below grade structures,
proper drainage will reduce
hydrostatic pressure by chan-
neling water away from the
structure. For horizontal
applications, in particular dead
level or low slope structures,
proper drainage can provide
an avenue for the water to flow
to the drains between the
membrane and topping
materials. For between slab
applications, it can decrease
the risk of possible freeze thaw
damage to the wearing
surface.
Millions of square feet of
Hydrodrain drainage compos-
ites have been specified by
architects and engineers
nationwide for over fifteen
years. Products are comprised
of a high density polyethylene
core and filter fabric. They
have superior chemical resis-
tance and are highly resistant
to various hydrocarbons.
Hydrotech offers a wide variety
of cost effective, state-of-the-art
drainage mediums. Typical
uses include plaza decks, roof
gardens, planters, retaining
walls, and foundation walls.
HYDRODRAIN 400A dimple core compositewith a non-woven needle-punched filter fabric onone side. Product has ahigh flow capacity and isdesigned to be used invertical applications toreduce hydrostaticpressure.
HYDRODRAIN 420A dimple core compositewith a non-woven needle-punched filter fabric. Apolymeric laminate isbonded to the back sideof the core. Product has ahigh flow capacity and isdesigned to be used invertical applications toreduce hydrostaticpressure. Product can beinstalled directly overLM6090, MM7800 andVM75.
HYDRODRAIN 700A dimple core compositewith a woven fabricbonded to the core.Product is a high-perfor-mance, superior flowcapacity drainagemedium to be used inhorizontal or verticalapplications.
Cover Photo: Inventure PlaceAkron, Ohio
P R O F I L E S
HYDRODRAIN 300A geonet composite with anon-woven needle-punchedfilter fabric bonded on oneside. Product is crush-proof,having superior dynamicloading strength in bothcompression and sheer.For horizontal and verticaluse. Ideal for areas sub-jected to heavy loading orvehicular traffic.
HYDRODRAIN 302A geonet composite witha non-woven needle-punched filter fabricbonded on two sides.Product is crush-proof,having superior dynamicloading strength in bothcompression and sheer.Horizontal and verticaluse, e.g. lagging walls.
HYDRODRAIN 1000A geonet composite witha non-woven needle-punched fabric bondedon one side. A polymericlaminate is bonded to theback side of the core.Product is crush proof andcan be used in bothhorizontal and verticalapplications. Product canbe installed directly overLM6090, MM7800 andVM75.
HYDRODRAIN ALA 1⁄8" geonet compositewith a non-woven needle-punched fabric bonded toone side. This product isideal for use in split-slabconstruction or paverconfigurations where an airspace is required to preventfreeze-thaw damage to thewearing surface.
CONCRETE
HYDRODRAIN AL
STYROFOAM
HYDRODRAIN
HYDROFLEX 30
MM6125
SURFACE CONDITIONER
CONCRETE
For further information onHYDRODRAIN, product data sheetsand specifications, please contactHydrotech directly.
Drainage requirements may vary upon application. Consult Hydrotech for recommendation.
CANADAHydrotech Membrane Corporation 10,951 Parkway, Ville D’Anjou, Quebec H1J 1S1Montreal 800.361.8924 514.353.6000 FAX 514.354.6649Toronto 800.668.8963 905.471.6677 FAX 905.471.6699
UNITED STATESAmerican Hydrotech Inc. 303 East Ohio Street, Chicago, Illinois 60611-3387Chicago 800.877.6125 312.337.4998 FAX 312.661.0731Seattle 206.441.6125 FAX 206.441.0914Washington, D.C. 804.378.6125 FAX 804.379.9367
WORLDWIDEWorld Wide Web: http://www.hydrotechusa.com
We hope the information given here will be helpful. It is based on data and knowledge considered to be true and correct and is offered for the user’s consideration,investigation and verification. The information is subject to change without notice. The determination of suitability and fitness of the products and the application describedherein for a particular purpose is the sole responsibility of the user. Please read all statements, recommendations and suggestions in conjunction with the conditions of salewhich apply to all goods sold by American Hydrotech, Inc. for the United States and abroad, or Hydrotech Membrane Corporation for Canada, including the expressdisclaimers by each company of the implied warranties of merchantability or fitness for a particular purpose. This brochure supersedes all previous Hydrodrain brochures.Nothing stated herein is intended to infringe on any patent or copyright.
© 1997 AMERICAN HYDROTECH INC.
TESTPROPERTY METHOD 300 302 1000 400 420 700
Color Black Black Black Black Black Black
Compressive ASTM 30,000 psf 30,000 psf 30,000psf 15,000 psf 15,000 psf 18,000 psfStrength D-1621 1438 kN/m2 1438 kN/m2 1438 kN/m2 719 kN/m2 719 kN/m2 862 kN/m2
Thickness ASTM .22 in .22 in .25 in .38 in .38 in .38 inD-1777 .56 cm .56 cm .63 cm .95 cm .95 cm .95 cm
Core Flow,Q @ 3600 psf ASTM 7 g/min/ft. 5.5 g/min/ft. 7 g/min/ft. 15 g/min/ft. 15 g/min/ft. 18 g/min/ft.width& Hydraulic D-4716 width width width width width
Gradient 1.0, 87 l/min/m 68 l/min/m 87 l/min/m 188 l/min/m 188 l/min/m 226 l/min/m width300 Hrs. width width width width width
Non-Woven WovenFabric ASTM 150 gpmin/ft.2 150 gpmin/ft.2 150 gpmin/ft.2 150 gpmin/ft.2 150 gpmin/ft.2 150 gpmin/ft.2 110 gpmin/ft.2
Flow D-4491 6105 lpmin/m2 6105 lpmin/m2 6105 lpmin/m2 6105 lpmin/m2 6105 lpmin/m2 6105 lpmin/m2 4475 lpmin/m2
Puncture ASTM 65 lbs. 65 lbs. 65 lbs. 65 lbs. 65 lbs. 65 lbs. 130lbs.Resistance D-4833 .24 kN .24 kN .24kN .24 kN .24 kN .24 kN .58 kN
Fabric CW 02215 70 US 70 US 70 US 70 US 70 US 70 US 30 USAOS (EOS) .212 mm .212 mm .212 mm .212 mm .212 mm .212 mm .60 mm
Fabric ASTM 90 lbs. 90 lbs. 90 lbs. 90 lbs. 90 lbs. 90 lbs. 360 x 260Grab Tensile D-4632 .40 kN .40 kN .40 kN .40 kN .40 kN .40 kN 445 x 355N
Fabric U.V. ASTM Stabilized Stabilized Stabilized Stabilized Stabilized Stabilized StabilizedResistance D-4355
Fungus ASTM No Growth No Growth No Growth No Growth No Growth No Growth No GrowthResistance D-1612 or
ASTMD-695
TM