HITACHI ELECTRIC CHAIN HOISTS
Hitachi’s reputation for excellence in design, quality, reliability and performance has made this brand a global market
leader. With over three decades of proven reliability throughout Australasia and an extensive operating range, Hitachi
Electric Chain Hoists are suited to most applications. The Hitachi models vary from 250kg to 15 tonne capacity and
are available in three or single phase, two speed or single speed while being tested to the Australian standards.
Features
All Hitachi models are manufactured to comply with AS1418.2.
Operation: fully contactorised with high rated contactors and pendant controls;
both fitted with mechanical interlocks and 24 Volt control.
Optional IP65 pendant including E-Stop available.
Safety Limits: full current and shunt limit switches operate in both directions of
hook travel.
Overload Limiter: this electro-mechanical device is exclusive to the Hitachi
range and boasts a far more superior overload protection device than the
slipping clutch method. Available on all Hitachi models.
Braking: all models are fitted with an electro-magnetic, self-adjusting disc type
brake to the gearbox and the “F” models have an additional auxiliary
centrifugal brake fitted to the motor.
Chain Bucket: noiseless design with flexible mounting.
High quality Grade 80 zinc or nickel plated load chain supplied as standard.
IP54 protection rating on all electric hoists and trolleys.
Motor thermal protection on all Hitachi models.
Optional radio remote control.
Ambient temperature requirement of -10 to 40 degrees.
Class M4 inclusive of 180 starts per hour.
Completely enclosed design. Entire mechanism including; the motor, dual brake system, gears, rotating parts and
electrical system can be operated under severe conditions.
Reverse phase protection relay on all models excluding; 250kg, 500kg and all single phase models.
Special low headroom hoist and trolley arrangements available to suit tight headroom applications.
Electric trolleys are fitted with Guide Rollers as standard to reduce wear and ensure suitability for curved beam
applications.
Specifications
THREE PHASE / SINGLE SPEED HOISTS - 415Volt, 50Hz
THREE PHASE / TWO SPEED HOISTS - 415Volt, 50Hz
SINGLE PHASE / SINGLE SPEED HOISTS - 240Volt, 50Hz
MODEL ¼S ½S 1S 2S 1F 2F 3F 5F
Stock Code HEH010 HEH050 HEH100 HEH200 HEH110 HEH210 HEH300 HEH500
Rated Capacity (kg) 250 500 1000 2000 1000 2000 3000 5000
Speed (m/min) 10 7.2 4.6 2.3 7.1 6.8 4.1 2.8
Motor (kW) 0.45 0.63 0.8 0.8 1.3 2.4 2.4 2.4
Weight (kg) 28 31 37 49 42 80 99 121
Headroom (mm) 450 450 530 645 535 660 820 1020
MODEL ¼SN ½SN 1SN 2SN 2FN 3FN 5FN
Stock Code HEH020 HEH060 HEH120 HEH220 HEH230 HEH330 HEH530
Rated Capacity (kg) 250 500 1000 2000 2000 3000 5000
Speed (m/min) 7.2 / 1.8 7.2 / 1.8 4.6 / 1.2 2.3 / 0.6 6.8 / 1.7 4.0 / 1.0 2.8 / 0.7
Motor (kW) 0.32 / 0.08 0.63 / 0.16 0.8 / 0.2 0.8 / 0.2 2.4 / 0.6 2.4 / 0.6 2.4 / 0.6
Weight (kg) 33 36 42 54 96 112 146
Headroom (mm) 450 450 530 645 660 820 1020
MODEL ¼S1 ½S1 1S1 2S1
Stock Code HEH900 HEH907 HEH911 HEH920
Rated Capacity (kg) 250 500 1000 2000
Speed (m/min) 5 3.6 2.3 1.1
Motor (kW) 0.25 0.32 0.4 0.4
Weight (kg) 34 34 39 51
Headroom (mm) 450 450 530 645
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
THREE PHASE / ELECTRIC TROLLEYS - 415Volt, 50Hz
MODEL 1ET 2ET 3ET 5ET
Stock Code HET100 HET200 HET300 HET500
Rated Capacity (kg) 1000 2000 3000 5000
ET Speed (m/min) Single Speed ET 10.5 or 21.0
ETN Speed (m/min) Two Speed ETN 21.0 / 5.3
Motor (kW) 0.14 0.14 0.3 0.3
Weight (kg) 38 52 60 86
Min, Radius (m) 1.5 1.8 2.0 3.0
Girder Width (mm) * 75 – 125 100 - 150 100 - 150 125 - 175
* Larger girder widths are available upon request.
Dimensions (in mm)
HITACHI S SERIES HOISTS
MODEL ¼S ¼SN ½S ½SN 1S 1SN 2S 2SN ¼S1 ½S1 1S1 2S1
Z 450 450 450 450 530 530 645 645 450 450 530 645
A 181 183 181 183 216 216 216 216 181 181 246 246
B 184 210 184 210 216 246 216 246 210 210 246 246
C 125 125 125 125 135 135 90 90 125 125 135 90
D 165 185 165 185 170 170 215 215 165 165 170 215
E 620 620 620 620 680 680 705 705 620 620 680 705
G 19 19 19 19 23 23 26 26 19 19 23 26
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
HITACHI F SERIES HOISTS
HITACHI ET SERIES TROLLEYS
MODEL 1F 2F 2FN 3F 3FN 5F 5FN
Z 535 660 660 820 820 1020 1020
A 250 280 280 280 280 280 280
B 250 280 330 280 330 280 330
C 135 175 175 120 120 145 145
D 170 170 170 245 245 330 330
E 680 845 845 1090 1090 1295 1295
G 23 26 26 42 42 48 48
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
MODEL 1ET 2ET 3ET 5ET
B1 185 210 210 240
B2 190 210 210 240
D 64 75 75 90
d 27 32 37 46
F 303 313 316 323
H 226 245 265 322
K 136 130 140 177
T 65 80 80 90
U 55 40 37.5 54
V 159 172 175 181
L 182 200 203 219
W 120 148 148 173
E 133 169 168 202
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC ELECTRIC CHAIN HOISTS
The Pacific Electric Chain Hoists offer a great balance between quality and price. The models vary from
250kg to 2 tonne capacity and are all tested to the Australian standards. All hoists are inclusive of many
features which makes them suited for most applications. Optional Motorised Trolleys are available to
complete the package.
Features
All Pacific models are manufactured to comply with AS1418.2.
IP65 pendant with 24 volt control for operator safety.
Overload protection clutch prevents damage caused by
overloading.
Inclusive of DC Brake which automatically engages in the event of
a power failure.
Completely enclosed design to withstand harsh conditions.
Upper and lower electrical limit switches.
Grade 80 zinc plated load chain supplied as standard.
Motor thermal protection on all Pacific Electric Chain Hoists.
Fuse protection provided for both primary and secondary control
circuits.
IP54 protection rating on all electric hoists and trolleys.
Reverse phase protection relay on all models excluding 250kg.
Optional radio remote control.
Specifications
Pacific Electric Chain Hoists - 415Volt, 50Hz
Motorised Trolleys - 415Volt, 50Hz
*Standard beam sizes available up to 300mm width. Larger sizes available upon request.
Dimensions (in mm)
Pacific Electric Chain Hoists
MODEL PEH025 PEH050 PEH100 PEH200
Stock Code PEH025 PEH050 PEH100 PEH200
Rated Capacity (kg) 250 500 1000 2000
Standard Lift Height (m) 3 3 3 3
Chain Dimension (mm) 4 x 12 6.3 x 19.1 7.1 x 20.2 7.1 x 20.2
Speed (m/min) 12 / 3 10 / 2.5 8 / 2 4 / 1
Motor (kW) 0.6 / 0.15 1.1 / 0.28 1.5 / 0.37 1.5 / 0.37
E.D. Rating (%) 40 / 20 40 / 20 40 / 20 40 / 20
Load Chain Fall No. 1 1 1 2
Weight (kg) 30 42 57 62
MODEL PET050 PET100 PET200 PET055 PET105 PET205
Stock Code PET050 PET100 PET200 PET055 PET105 PET205
Rated Capacity (kg) 500 1000 2000 500 1000 2000
Speed (m/min) 10 10 10 20 / 5 20 / 5 20 / 5
Motor (kW) 0.12 0.18 0.37 0.12 / 0.03 0.18 / 0.04 0.37 / 0.09
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Pacific Electric Chain Hoists plus Trolley
MODEL PEH025 PEH050 PEH100 PEH200
A 380 468 487 487
B 175 221 240 240
C 205 247 248 248
D 135 156 170 170
E 299 366 398 398
F 143 186 188 188
G 156 180 210 210
H 376 485 520 592
MODEL PEH025 +
PET055
PEH050 +
PET050
PEH100 +
PET105
PEH200 +
PET205
A 382 382 382 392
B 125.5 125.5 125.5 159
C 324 324 324 357
D 180 180 180 183
E 75 - 125 75 - 125 75 - 125 100 – 150
H 385 483 510 582
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC PORTA HOISTS
The Pacific Porta Hoists are compact, lightweight 240 volt single phase electric chain hoists. They
conveniently come in a durable travel case which makes them the ideal portable solution for lifting,
lowering and handling loads up to 500kg. All models are tested to the Australian standards.
Features
All Pacific Porta Hoists are manufactured to comply with AS1418.2.
All models suitable for 240 volt, 50 Hz single phase power supply.
Available in 80kg, 125kg, 250kg and 500kg capacities.
Duty cycle rated at 30% ED with 180 starts per hour
18 volt DC low voltage control for safe operation.
IP65 pendant control, dual speeds with variable speed slow control for
raise and lower.
Overload protection clutch prevents damage caused by overloading.
All models are supplied as standard with 6 metre height of lift, a 5 metre
pendant control, chain bucket and 3 metre power supply cable.
Upper and lower electrical limit switches.
Supplied with durable travel case.
Specifications
*Additional height of lift is available upon request. Please note that this may vary the size and weight of the hoist and therefore may not fit into the travel case.
Dimensions (in mm)
MODEL PPH080 PPH125 PPH240 PPH500
Stock Code PPH080 PPH125 PPH240 PPH500
Rated Capacity (kg) 80 125 250 500
Standard Lift Height (m) 6 6 6 6
Pendant Length (m) 5 5 5 5
Power Supply 50Hz (volt) 240 240 240 240
Chain Dimension (mm) 4.0 x 12 4.0 x 12 4.0 x 12 4.0 x 12
Motor Power (kW) 0.3 0.3 0.6 0.6
Speed (m/min) 0 - 4.8 (variable) /
18
0 - 3.2 (variable) /
12.5
0 - 3.2 (variable) /
12.5
0 - 1.6 (variable) /
6.3
IP Rating 54 54 54 54
E.D. Rating (%) 30 30 30 30
Load Chain Fall No. 1 1 1 2
Weight (kg) 17.5 17.5 17.5 20.6
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
MODEL PPH080 PPH125 PPH240 PPH500
A 364 364 364 364
B 182 182 182 182
C 182 182 182 182
D 89 89 89 89
E 423 423 423 423
F 6m lift 6m lift 6m lift 6m lift
G 25 25 25 25
H 25 25 25 25
I 260 260 260 260
J 108 108 108 84
K 152 152 152 176
L 400 400 400 494
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC ELECTRIC WIRE ROPE HOISTS
The Pacific Electric Wire Rope Hoists are suited for a wide range of applications such as warehouses,
construction sites and factories. Due to its compact and lightweight design, it is perfect for when easy
installation and quick use is needed.
Features
Automatic upper limit switch; when rope disc touches the limit arm,
hoisting is automatically stopped.
Dynamic and mechanical brake providing instant and safe braking.
Convenient 240V / single phase power supply.
Sensor arm automatically activates lower limit switch to stop motor
if rope is under wound.
Supplied with 3m power lead and industry plug & 10m heavy duty
IP65 waterproof pendant control.
Wire rope with 360º weighted hook with safety latch.
Optional push trolley mount CRH0720
Optional mounting arm CRH0710 (not available for CWS300).
Specifications
Optional Attachments
Dimensions (in mm)
MODEL CWS80 CWS160 CWS230 CWS300
Stock Code CWS080 CWS160 CWS230 CWS300
Rated Capacity (kg) 80 160 230 300
Speed (m/min / 50Hz) 30 22 14 13
Motor Output (kW) 0.8 1.2 1.3 1.5
Power Supply 240V 1Ø 50Hz
Max. Height of Lift (m) 35 40 24 24
Wire Rope Dimension (Ø mmxm) 3.3 x 36 4.0 x 41 5.0 x 25 4.8 x 25
Net Weight (kg) 18 25 26 28
MODEL CRH0710 CRH0720 CRH0720A
Stock Code CRH071 666110 666111
Description Swivel arm assembly
Trolley mount bracket to fit
hoist to PPT105 push trolley.
Suitable for CWS80
Trolley mount bracket to fit
hoist to PPT105 push trolley.
Suitable for CWS160 /
CWS230 / CWS300
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions
MODEL CWS80 CWS160 CWS230 CWS300
A 200 244 244 244
B 168 182 182 182
C Ø65 Ø60 Ø60 Ø60
D 605 640 640 640
E 879 879 879 879
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN AIR HOISTS
J.D. Neuhaus manufactures high quality, superior PROFI Air Hoists which are known for their robust
designs. This makes their products suitable for tough industrial applications, even in continuous working
processes. Safety features, as 100% duty rating and explosion protecting, are an important advantage
for applications in hazardous areas.
Features
Manufactured in Germany, under strict quality control with demanding tolerances.
All JDN models are manufactured to comply with AS1418.2.
Patented pre-lube motor design for low maintenance, oil-free operation.
100% duty rating and unlimited duty cycle suits all environmental conditions.
Only six atmospheres of compressed air required.
Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
ATEX–approved models available, suitable for application in dangerous and
explosive environments
Self-cooling economic air motor which will not overheat.
Fail-safe brake, in case of air supply failure.
From 1 tonne upwards available with overload protection.
Low decibel rating.
F-type sensitive infinitely variable speed control for the precise positioning of
loads.
Cord control or Brass Pendant control available, as well as an electro pneumatic
interface for Radio Remote control as an option.
Easy operation and low maintenance design.
Specifications
*PROFI range available up to 100 tonne.
**Chain buckets, longer lift heights and alternative controllers available at additional cost.
***Weight and headroom based on PROFI standard model with rope control and no chain bucket.
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti
Stock Code JDN705 JDN706 JDN715 JDN719 JDN725 JDN735
Rated Capacity (tonne) 0.25 0.5 1 1.6 2 3.2
Weight with standard 3m lift (m) 27 27 28 56 34 86
No. of chain strands 1 1 1 1 2 1
Motor Power (kW) 1.0 1.0 1.0 1.3 – 2 1.0 3.5
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 9 x 27 7 x 21 13 x 36
Air Pressure (bar) 6 6 6 4 - 6 6 6
Air Consumption at full load (m³/min)
Lifting
Lowering
1.2
1.5
1.2
1.5
1.2
1.5
1.5–2.6
2.2–3.6
1.2
1.5
4
5.5
Air Connection G½ G½ G½ G¾ G½ G¾
Lifting speed at full load (m/min) 20 11 5.5 4 – 6 2.7 5
Lowering speed at full load (m/min) 38 17 11 11 – 12 5.5 10.8
Model 3Ti/2 6Ti 10Ti 16Ti 20Ti
Stock Code JDN732 JDN765 JDN775 JDN785 JDN795
Rated Capacity (tonne) 3.2 6.3 10 16 20
Weight with standard 3m lift (m) 66 110 156 240 285
No. of chain strands 2 2 2 3 4
Motor Power (kW) 1.3 – 2 3.5 3.5 3.5 3.5
Chain Dimension (mm) 9 x 27 13 x 36 16 x 45 16 x 45 16 x 45
Air Pressure (bar) 4 – 6 6 6 6 6
Air Consumption at full load (m³/min)
Lifting
Lowering
1.5–2.6
2.2–3.6
4
5.5
4
5.5
4
5.5
4
5.5
Air Connection G¾ G¾ G¾ G¾ G¾
Lifting speed at full load (m/min) 2 – 3 2.5 1.6 1 0.7
Lowering speed at full load (m/min) 5.5 – 6 5.4 3.4 2.1 1.6
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
¹Chain buckets increase the hoist headroom
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
A (min. headroom¹) 450 450 450 480 498 593 544 674 813 898 1030
B 288 288 288 293 336 373 356 454 548 598 670
C 145 145 145 200 145 233 200 233 308 382 382
D 297 297 297 412 297 483 412 483 575 692 692
E1 28 28 28 28 28 40 28 40 44 53 75
E2 28 28 28 26 28 30 28 40 44 53 75
F (up to hook centre) 137 137 137 170 137 187 140 154 197 199 180
G (max. width) 176 176 176 215 183 233 215 233 306 308 315
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN MINI AIR HOISTS
The JDN Mini Series widens the range of applications in the light duty sector as a handy, flexible and
light-weight hoist. The optional Mini Manipulator can be used to lift, lower, traverse and position loads in
an easy, manual manner. The carrying capacities vary from 125kg to 980kg, with the 125kg model and
the 250kg available with optional travel case.
Features
Manufactured in Germany, under strict quality control with demanding tolerances.
All JDN models are manufactured to comply with AS1418.2.
Patented pre-lube motor design for low maintenance, oil-free operation.
100% duty rating and unlimited duty cycle suits all environmental conditions.
Only six atmospheres of compressed air required.
Insensitive to dust, humidity and temperatures ranging from -20 °C up to + 70 °C.
ATEX–approved models available, suitable for application in dangerous and explosive environments.
Also suitable for horizontal pulling.
Self-cooling economic air motor which will not overheat.
Fail-safe brake, in case of air supply failure.
Wear resistant motor braking system.
Extremely sensitive lever control with emergency shut-off valve; maximum control length is 6 metres.
Price competitive alternative when compared to other types of powered hoists.
Easy operation and low maintenance design.
Lightweight for easy handling.
Specifications
* Custom lift heights available. Weight and headroom based on mini standard model with pendant control and chain bucket. ** Pneumatic trolleys and cord controls not available for this range.
Dimensions (in mm)
Model MINI125 MINI250 MINI500 MINI1000
Stock Code JDN123 JDN253 JDN503 JDN603
Rated Capacity (kg) 125 250 500 980
Weight with standard 3m lift (kg) 9.5 10.5 21 23
No. of chain strands 1 1 1 1
Motor Output (kW) 0.4 0.4 1 1
Chain Dimension (mm) 4 x 12 4 x 12 7 x 21 7 x 21
Air Pressure (bar) 6 6 6 6
Air Consumption at full load (m³/min)
Lifting
Lowering
0.5
0.7
0.5
0.7
1.2
1.6
1.2
1.6
Air Connection G⅜ G⅜ G½ G½
Lifting speed at full load (m/min) 15 8 10 5
Lowering speed at full load (m/min) 30 16 18 10
Model MINI125 MINI250 MINI500 MINI1000
A 328 328 458 458
B 232 232 316 316
C 367 367 505 505
D 92 92 122 122
E 213 213 292 292
F 109 109 148 148
G 104 104 144 144
H 177 177 234 234
J 148 148 194 194
K 83 83 119 119
L 29 29 40 40
M 19 19 28 28
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN MINING AIR HOISTS
The JDN M-series are specifically designed for underground mining operations where loads can be lifted, lowered and horizontally pulled. Due to their versatility, they are also suitable for many different industrial applications. The M-series have the same features as the JDN PROFI-series, however; they operate with an air pressure of only 4 bar.
Features
Manufactured in Germany, under strict quality control with
demanding tolerances.
All JDN models are manufactured to comply with AS1418.2.
Patented pre-lube motor design for low maintenance, oil-free
operation.
100% duty rating and unlimited duty cycle suits all environmental
conditions.
Insensitive to dust, humidity and temperatures ranging from -20
°C up to + 70 °C.
ATEX–approved models available, suitable for application in
dangerous and explosive environments
Fail-safe brake, in case of air supply failure.
Cast iron housing suitable for severe conditions.
Easy operation and low maintenance design.
Two chain falls for operation in both directions.
Specially designed for horizontal and vertical moving of loads.
Specifications
* Custom lift heights available. Weight based on standard model. Lifting speed at 2m length of control. Longer control hoses decrease the lifting speeds.
Dimensions (in mm)
Model M64 M63D
Stock Code JDN991 JDN990
Rated Capacity (tonne) 1 - 2 3 - 6
Weight with standard 3m lift (kg) 60 100
No. of chain strands 1 - 2 1 - 2
Motor Output (kW) 0.77 1.3
Chain Dimension (mm) 9 x 27 13 x 36
Air Pressure (bar) 4 4
Air Consumption at full load (m³/min)
Lifting
Lowering
1.0
2.0
2.2
3.2
Air Connection Rd 32 x ⅛” Rd 32 x ⅛”
Lifting speed at full load (m/min) 3 – 1.5 2.2 – 1.1
Lowering speed at full load (m/min) 12.5 – 6.5 6 - 3
Model M64 M63D
A1 (smallest headroom with 1/1 chain strands) 603 750
A2 (smallest headroom with 1/2 chain strands) 660 870
B1 (with 1/1 chain strands) 313 370
B2 (with 1/2 chain strands) 370 490
C 175 237
D 375 507
E1 (Hook opening) 30 40
E2 (Hook opening) 30 40
E3 (Hook opening) 30 30
F (maximum width) 144 195
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN SUBSEA HOISTS
J.D. Neuhaus have been writing hoist technology history for over 260 years through consistent product
innovations. Today, JDN air hoists are used in more than 70 different industries in over 90 different
countries. That the expertise of JDN goes beyond the border is proven by their latest technology in
SubSea hoisting, of which the world launch was hosted in Australia. The new JDN PROFI SubSea
series are developed to be used in complex underwater lifting operations; using variable speed control
and overload protection with an operating depth of up to 70m in water. JDN offer air and hydraulic
options, in capacities of 3 to 6 tonnes.
Features
Manufactured in Germany, under strict quality control
with demanding tolerances.
All JDN models comply with AS1418.2.
Available with air or hydraulic operation.
Variable speed control.
Supplied with overload protection.
Design for water operating depth of up to 70m.
For both horizontal and oblique use.
Specifications
Dimensions (in mm)
Model 3TI - SUBSEA 6TI - SUBSEA
Stock Code JDN737 JDN767
Rated Capacity (tonne) 3.2 6.3
Weight with standard 3m lift (kg) 150 161.5
Motor Output (kW) 3 3
Chain Dimension (mm) 13 x 36 13 x 36
No. of Chain Strands 1 2
Air Pressure (bar) 6 6
Air Consumption at full load (m³/min)
Lifting
Lowering
4
5.5
4
5.5
Air Connection G1 G1
Lifting speed at full load (m/min) 2.3 1.2
Lowering speed at full load (m/min) 5.4 2.7
Length of Control at standard lift (m) 2 2
Max. water depth (m) 55² 55²
Model 3TI - SUBSEA 6TI - SUBSEA
A 593 674
B 373 454
C1 300 300
C2 455 455
D 755 755
E1 40 40
E2 30 40
F 187 154
G 233 233
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN HYDRAULIC MONORAIL HOISTS
The JDN Hydraulic Monorail Hoists can be deployed as an alternative to air driven units in all situations
where hydraulic lines, central hydraulic systems or hydraulic power supplies exist. The carrying
capacities vary from 3 tonne up to 100 tonne and depending on the motor size; these hoists work with an
intake pressure of 100 bar up to 180 bar.
Features
Manufactured in Germany, under strict quality control with
demanding tolerances.
All JDN models are manufactured to comply with
AS1418.2.
Ideal for applications in explosion risk areas.
Sensitive, infinitely variable speed control of lifting /
lowering and travelling motions.
Extremely low noise emissions
Fully enclosed highly robust gear motor.
Integrated overload protection.
Only two supply connections at hoist “P” and “T”, leakage
oil drained internally.
Controlled load-lowering up to 20 tonne carrying capacities
in the event of oil supply failure.
Specifications
JDN Hydraulic PROFI Hoists (available up to 100 tonne)
Model 3 TI-H 6 TI-H 10 TI-H 16 TI-H 20 TI-H
Stock Code - - - - -
Rated Capacity (tonne) 3.2 6.3 10 16 20
No. of chain strands 1 2 2 3 4
Motor Type KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16
Motor Power (kW) 3.5 3.5 3.5 3.5 3.5
Intake Pressure (bar) 130 130 130 130 130
Intake Volume (l/min) 48 48 48 48 48
Lifting speed at full load (m/min) 4.0 2.0 1.7 1.1 0.8
Lowering speed at full load (m/min) 4.5 2.3 2.1 1.5 1.0
Weight with standard lift height (kg) 90 114 160 244 289
Chain Dimension (mm) 13 x 36 13 x 36 16 x 45 16 x 45 16 x 45
Weight of chain (kg/m) 3.8 3.8 5.8 5.8 5.8
Standard Lift (m) 3 3 3 3 3
Length of control as standard lift (m) 2 2 2 2 2
JDN Hydraulic Monorail Hoists
Model EH 20-H EH 25-H EH 37-H EH 50-H EH 75-H EH 100-H
Stock Code JDN810 - - JDN850 - -
Rated Capacity (tonne) 20 25 37.5 50 75 100
No. of chain strands 4 2 3 4 3 4
Motor Type – Trolley KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16 KM 1/16
Motor Type – Hoist KM 1/8 – KM 1/16 KM 2/32 KM 2/32 KM 2/32 KM 2/32 KM 2/32
Motor Output – Trolley (kW) 0.7 1.4 1.4 1.4 2.8 2.8
Motor Output – Hoist (kW) 3.5 6 6 6 10 10
Intake Pressure (bar) 160 / 100 150 150 150 180 180
Lifting speed at full load (m/min) 0.8 1.1 0.7 0.5 0.7 0.55
Lowering speed at full load (m/min) 0.9 1.2 0.8 0.6 0.8 0.6
Travelling Speed 12 12 12 12 12 12
Connection G½ G¾ G¾ G¾ G¾ G¾
Hose Dimension DN 12 DN 16 DN 16 DN 16 DN 16 DN 16
Weight with standard lift height (kg) 720 1050 1550 1880 4100 5800
Chain Dimension (mm) 16 x 45 23.5 x 66 23.5 x 66 23.5 x 66 32 x 90 32 x 90
Weight of chain (kg/m) 5.8 12.2 12.2 12.2 21.3 21.3
Standard Lift (m) 3 3 3 3 3 3
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
JDN Hydraulic PROFI Hoists
¹Chain buckets increase the hoist headroom
Model 3 TI-H 6 TI-H 10 TI-H 16 TI-H 20 TI-H
A (smallest headroom¹) 593 674 813 898 1030
B 373 454 548 598 670
C 233 233 308 382 382
D 578 578 670 787 787
E1 40 40 44 53 75
E2 30 40 44 53 75
F 187 154 197 199 180
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions continued (in mm)
JDN Hydraulic Monorail Hoists
¹Chain buckets increase the hoist headroom
Model EH 20-H EH 25-H EH 37-H EH 50-H EH 75-H EH 100-H
A 130 146 146 125 100 125
B 68 70 70 68 68 68
C 267 257 267 272 267 272
D 35 25 25 40 35 40
E 220 198 220 283 220 283
F¹ 820 998 1070 1150 1480 1535
G 200 170 190 420 286 575
H 75 75 100 100 120 120
J 266 350 455 340 740 470
K 600 1185 1730 1680 3210 3130
L 367 377 377 462 640 762
M 420 562 562 687 670 765
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN BIG BAG HANDLING AIR HOISTS
For Big Bag Handling JDN offers innovative design solutions to meet the special requirements for these
applications. These Air Hoists are available in capacities of 1100kg and 2200kg with an air pressure of 6
bar and are supplied with one or two load hooks. One load hook for standard cross lifting beam design.
The extended distance between the hook and the chain box is particularly advantageous since this
guarantees no risk of collision between the load and the chain box. The twin loads hooks are suited for
more complex multipoint cross beam designs or for standard lifting beam designs with two suspension
points.
Features
Manufactured in Germany, under strict quality control with demanding tolerances.
All JDN models are manufactured to comply with AS1418.2.
Particularly suited for use as big bag handling hoist and for the movements of bulky loads due to the low headroom design.
Compact and modern design.
Suitable for use as a synchronized hoist in twin-hook design.
The use of JDN standard components guarantees reliable operation and cost effective manufacture.
No additional motor lubrication required.
Small number of maintenance / wear free moving parts.
Chain box included as standard.
Suitable for a wide variety of beam sizes / profiles, with hook centres to suit your requirements.
100% duty rating and unlimited duty cycle suits all environmental conditions.
Suitable for use as standard in areas at risk of explosion with ATEX–approved models available, for application in dangerous and explosive environments
Specifications
Model BBH 1000-1 BBH 2000-1 BBH 1000-2 BBH 2000-2
Stock Code JDN900 - - -\
No. of hooks 1 1 2 2
Air Pressure (bar) 6 6 6 6
Rated Capacity (tonne) 1.1 2.2 1.1 2.2
No. of chain strands 1 2 2 4
Motor Output – Hoist (kW) 0.7 0.7 0.7 0.7
Motor Output – Trolley (kW) 0.2 0.2 0.2 0.2
Lifting speed at full load (m/min) 3.7 1.7 3.7 1.7
Lowering speed at full load (m/min) 10 5 10 5
Air consumption at full load (m³/min) 1.4 1.4 1.4 1.4
Weight with standard lift and
minimum k dimension (kg) 130 137 137 149
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 7 x 21
Weight of 1m chain (kg) 1 1 1 1
Standard Lift (m) 3 3 3 3
Length of control at standard load (m) 2 2 2 2
Noise level at full load (dB (A)) 76 76 76 76
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
Model BBH 1000-1 BBH 2000-1 BBH 1000-2 BBH 2000-2
A 332 332 332 332
B 163 / 220 163 / 220 163 / 220 163 / 220
b min. 90 90 90 90
b max. 310 310 310 310
C 182 182 182 182
E 195 195 373 346
F 195 195 95 95
G 195 195 159 159
H 388 438 388 438
J 192 220 192 220
K min. 435 410 260 260
K max. 1100 1100 1300 1300
L - - 175 150
M 28 28 28 28
N 250 250 250 250
P 70 70 70 70
R 116 116 116 116
t max. 30 30 30 30
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN ULTRA LOW MONORAIL HOISTS
The JDN Ultra Low Monorail Hoist provides the ideal solution when loads have to be lifted and
transported in extremely reduced spaces. As an example; the model with a 6 tonne load capacity
features a headroom of only 230mm. The carrying capacity of these models vary from 4 tonne up to 100
tonne, with an air pressure of 6 bar.
Features
Manufactured in Germany, under strict
quality control with demanding tolerances.
All JDN models are manufactured to comply
with AS1418.2.
Ideal for applications in explosion risk areas.
Insensitive to dust, humidity and temperatures
ranging from -20 °C up to + 70 °C.
Extremely low headroom.
Low air consumption.
Available with increased spark protection.
Specifications
*Capacities up to 100 tonne available on request
Model UH 4 UH 6 UH 8 UH 12 UH 16
Stock Code - JDN806 JDN808 JDN999 -
Rated Capacity (tonne) 4 6 8 12 16
No. of chain strands 2 2 4 4 4
Air Pressure (bar) 6 6 6 6 6
Motor Output (kW) 2.5 2.5 2.5 2.5 2.5
Lifting speed at full load (m/min) 3.0 2.0 1.4 0.9 0.65
Lowering speed at full load (m/min) 7.5 5.2 3.6 2.5 1.5
Air consumption at full load (m³/min) 4.0 4.0 4.0 4.0 4.0
Weight with standard lift and control
length (kg) 460 470 540 550 560
Chain Dimension (mm) 13 x 36 13 x 36 13 x 36 13 x 36 13 x 36
Weight of 1m chain (kg) 3.8 3.8 3.8 3.8 3.8
Standard Lift (m) 3 3 3 3 3
Length of control at standard load (m) 2 2 2 2 2
Noise level at full load lifting (dB (A)) 78 78 78 78 78
Noise level at full load lowering (dB (A)) 80 80 80 80 80
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
Model UH 4 UH 6 UH 8 UH 12 UH 16
A 195 305 195 305 305
B 200 200 200 200 200
C 284 284 284 284 284
D 165 165 165 165 165
E 236 236 236 236 236
F 330 330 283 283 283
G 197.5 197.5 197.5 197.5 197.5
H min. 150 ≤ b ≤ 310 230 230 - - -
H min. 150 ≤ b ≤ 230 - - 295 295 334
H min. 230 ≤ b ≤ 310 - - 276 276 315
J 400 400 400 400 400
K 535 535 535 535 535
L 1000 1000 1000 1000 1000
M 40 40 44 44 53
N 51 51 66 66 82
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN TROLLEYS
JDN Trolleys are available for both the PROFI and Mining Air Hoists as a manual option (LN) for pushing
or pulling by hand. Geared trolleys (LH) are also available for load movement by operating the hand
chain mechanism and JDN also offers a motorised trolley (LM) which is powered by an air motor. The
carrying capacities go up to 20 tonne.
Features
Manufactured in Germany, under strict quality control with demanding tolerances.
All JDN trolleys are manufactured to comply with AS1418.2.
Easy to install.
Fitted with Anti-climb and anti-drop devices as standard.
Robust manufacture requiring little maintenance.
Able to negotiate curves.
Rack and pinion drive and spark resistance package available as options.
Four coat epoxy paint finish available for offshore protection.
The air supply can be fed by various systems; energy chain, c-rail, square rail, spiral hose or hose
trolleys.
JDN LN Manual Trolley JDN LH Geared Trolley JDN LM Motorised Trolley
Specifications
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
Stock Code - JDN925 JDN925 - JDN925 JDN931 - JDN960 JDN970 JDN970 JDN970
Rated Capacity – LN Trolley (tonne) 0.5 0.5 1 2 2 3.2 3.2 6.3 10–16 10–16 -
Rated Capacity – LH & LM Trolley (tonne) 2 2 2 2 2 3.2 3.2 6.3 10–16 10–16 20
Rated Capacity – Hoists incl. Trolley (tonne) 0.25 0.5 1 1.6 2 3.2 3.2 6.3 10 16 20
Weight – LN Trolley (kg) 7.7 7.7 10.5 18 18 26 26 117 190 190 -
Weight – LH Trolley (kg) 26 26 26 26 26 37 37 127 220 220 285
Weight – LM Trolley (kg) 26 26 26 26 26 33 33 124 220 220 285
Hose weight with standard lift (kg) 27 27 28 56 34 86 66 110 156 240 285
Weight with standard lift – LN Trolley (kg) 34.7 34.7 38.5 74 52 112 92 227 346 430 -
Weight with standard lift – LH Trolley (kg) 53 53 54 82 60 123 103 237 376 460 570
Weight with standard lift – LM Trolley (kg) 53 53 54 82 60 119 99 234 376 460 570
Weight of 1m chain (kg) 1 1 1 1.8 1 3.8 1.8 3.8 5.8 5.8 5.8
No. of chain strands 1 1 1 1 2 1 2 2 2 3 4
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 9 x 27 7 x 21 13 x 36 9 x 27 13 x 36 16 x 45 16 x 45 16 x 45
Air Pressure – LM Trolley (bar) 6 6 6 4 - 6 6 6 4 - 6 6 6 6 6
Air Consumption – LM Trolley (m³/min) 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 1.3 1.3 1.3
Air Consumption – Hoist (m³/min) 1.5 1.5 1.5 1.5–2.6 1.5 5.5 1.5–2.6 5.5 5.5 5.5 5.5
Motor Output – LM Trolley (kW) 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.7 0.7 0.7
Motor Output – Hoist (kW) 1 1 1 1.3 – 2 1 3.5 1.3 – 2 3.5 3.5 3.5 3.5
Travelling Speed – LM Trolley (m/min) 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14 5 / 12 5 / 12 5 / 12
Hose Connection – LM Trolley G½ G½ G½ G¾ G½ G¾ G¾ G¾ G¾ G¾ G¾
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
JDN Manual Trolleys (LN)
*Chain buckets increase the hoist headroom
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti
With trolley LN 0.5T LN 1T LN 2T LN 3.2T LN 6.3T LN 10-16T
A 260 260 260 310 310 292 292 500 490 490
B max. 119 119 122 122 162 113 162 141 142 142
C b + 28 b + 28 b + 28 b + 26 b + 26 b + 60 b + 60 b + 70 b + 70 b + 70
d 55 55 68 80 80 84 84 165 165 165
D max. 199 199 199 122 122 113 113 141 142 142
E 137 137 137 170 137 187 140 154 197 199
F 39 39 39 45 46 46 75 79 109 109
G 145 145 145 200 145 233 200 233 308 382
H 152 152 152 212 152 250 212 250 267 310
J* (mounted) - - - - - 635 613 763 929 982
J* (suspended) 530 530 530 588 597 798 - 919 1176 1260
K 67.5 67.5 81.5 94 94 108 107 188 188 188
L 28 28 28 26 28 30 28 40 44 53
M 42 42 42 40 42 42 42 51 66 82
N 130 130 130 150 150 136 136 236 236 236
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN Geared Trolleys (LH)
*Chain buckets increase the hoist headroom
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
With trolley LH 2T LH 3.2T LH 6.3T LH 10-16 LH 20T
A 250 250 250 250 250 292 292 500 490 490 600
B max. 130 130 130 130 130 113 113 141 142 142 132
C b + 36 b + 36 b + 36 b + 36 b + 36 b + 60 b + 60 b + 70 b + 70 b + 70 b + 68
d 70 70 70 70 70 84 84 165 165 165 185
D 284 284 284 283 284 294 297 307 320 320 320
E 137 137 137 170 137 187 140 154 197 199 180
F 39 39 39 45 46 46 75 79 109 109 135
G 145 145 145 200 145 233 200 233 308 382 382
H 152 152 152 212 152 250 212 250 267 310 310
J* (mounted) - - - - - 635 613 763 929 982 1125
J* (suspended) 563 563 563 602 611 798 - 919 1176 1171 1475
K 103 103 103 103 103 110 110 215 215 215 226
L 28 28 28 26 28 30 28 40 44 53 75
M 42 42 42 40 42 42 42 51 66 82 86
N 116 116 116 116 116 136 136 236 236 236 274
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN Motorised Trolleys (LM)
*Chain buckets increase the hoist headroom
Model 0.25Ti 0.5Ti 1Ti 1.5Ti 2Ti 3Ti 3Ti/2 6Ti 10Ti 16Ti 20Ti
With trolley LM 2T LM 3.2T LM 6.3T LM 10-16T LM 20T
A 250 250 250 250 250 292 292 500 490 490 600
B max. 130 130 130 130 130 113 113 141 142 142 132
C b + 36 b + 36 b + 36 b + 36 b + 36 b + 60 b + 60 b + 70 b + 70 b + 70 b + 68
d 70 70 70 70 70 84 84 165 165 165 185
D 183 183 183 185 183 191 191 205 328 328 328
E 137 137 137 170 137 187 140 154 197 199 180
F 39 39 39 45 46 46 75 79 109 109 135
G 145 145 145 200 145 233 200 233 308 382 382
H 152 152 152 212 152 250 212 250 267 310 310
J* (mounted) - - - - - 635 613 763 929 982 1125
J* (suspended) 563 563 563 602 611 798 - 919 1176 1171 1475
K 95 95 95 95 95 107 107 188 188 188 218
L 28 28 28 26 28 30 28 40 42 55 75
M 42 42 42 40 42 42 42 51 66 82 86
N 116 116 116 116 116 136 136 236 236 236 274
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN LOW HEADROOM TROLLEYS
The JDN Low Headroom Trolleys are the solution where headroom is restricted and standard trolleys
are unable to meet the lifting height requirements. This, together with having the JDN Air Hoist mounted
in a horizontal position, could just be the answer in a difficult lifting situation. The carrying capacity of
these models vary from 0.5 tonne up to 6.3 tonne, with an air pressure of 6 bar.
Features
Manufactured in Germany, under strict quality
control with demanding tolerances.
All JDN models are manufactured to comply
with AS1418.2.
Small number of maintenance / wear-free
moving parts.
No additional motor lubrication required.
Two-step travelling speed.
Adjustable trolley widths to suit your requirements.
Able to negotiate curves.
Extended trolley tie bars for bulky elongated loads.
Optional Rack and pinion drive, off shore paint and spark
resistant packages available
Various options for Air supply systems available
Specifications
Hoists & Trolley Model PROFI 0.5Ti
& LMF05 - 2t
PROFI 1Ti
& LMF05 - 2t
PROFI 2Ti
& LMF05 - 2t
PROFI 3Ti
& LMF3.2t
PROFI 6Ti
& LMF6.3t
Stock Code JDN706 JDN715 JDN725 JDN735 JDN765
Rated Capacity (tonne) 0.5 1 2 3.2 6.3
No. of chain strands 1 1 2 1 2
Motor Output – Hoist (kW) 1 1 1 3.5 3.5
Motor Output – Trolley (kW) 0.2 0.2 0.2 0.2 0.2
Air Pressure (bar) 6 6 6 6 6
Lifting speed at full load (m/min) 10 5 2.5 4.5 2.2
Lowering speed at full load (m/min) 17 11 5.5 10.8 5.4
Travelling speed at full load (m/min) 9 / 14 9 / 14 9 / 14 9 / 14 9 / 14
Air consumption at full load (m³/min) 1.2 1.2 1.2 1.2 1.2
Air Connection G½ G½ G½ G¾ G¾
Hose Dimension (mm) 13 13 13 19 19
Weight with standard lift & control (kg) 98 99 105 210 330
Chain Dimension (mm) 7 x 21 7 x 21 7 x 21 13 x 36 13 x 36
Weight of chain (kg) 1 1 1 3.8 3.8
Standard Lift (m) 3 3 3 3 3
Max. bottom flange – thickness (mm) 25 25 25 35 35
Max. bottom flange – width (mm) 310 310 310 310 310
Min. bottom flange – width (mm) 80 80 80 125 125
Noise level at full load lifting (dB (A)) 75 76 76 78 78
Noise level at full load lowering (dB (A)) 78 78 78 80 80
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
Hoists & Trolley Model PROFI 0.5Ti
& LMF 05 - 2t
PROFI 1Ti
& LMF 05 - 2t
PROFI 2Ti
& LMF 05 - 2t
PROFI 3Ti
& LMF 3.2t
PROFI 6Ti
& LMF 6.3t
A max. 105 105 105 105 106
B 36 36 36 36 70
b min. 80 80 80 80 125
C 164 164 164 164 169
D1 70 70 70 70 165
D2 70 70 70 70 70
E1 116 116 116 116 236
E2 116 116 116 116 116
F 172 172 195 228 351
G1 95 95 95 95 197
G2 95 95 95 95 95
H min. 320 320 394 415 537
J 320 320 320 397 397
K1 145 145 145 233 233
K2 152 152 152 248 248
L 715 715 715 825 995
M 28 28 28 30 40
N 42 42 42 42 51
t max. 25 25 25 35 35
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
JDN CONTROLS
JDN Air Hoists are available with various controls to suit every application.
Rope Control
The rope control provides infinite speed control for lifting and lowering and is
suitable for any required control length. The rope control is available for all
PROFI hoists up to 25 tonne carrying capacity. The PROFI 37Ti, 50Ti and
100Ti are fitted with a pull chain instead of a cord.
FI-Control
This FI-control allows infinitely variable speed control and the
ergonomic design of the synthetic housing ensures comfortable
handling for the operator. The use of non-rusting materials
allows the application in areas with aggressive substances in
the atmosphere. The control hoses are enclosed in an outer
sheath which protects them from external conditions.
F-Control
The F-control consists of unbreakable synthetic material resistant to
ambient influences. The ergonomically designed housing ensures ease of
handling. Up to 18 different control functions can be integrated into a
single pendant control; for example key switch, double stage travelling
speed and simultaneous control of several motors. The F-control can also
be delivered with optional infinitely variable control of hoisting and
travelling speeds.
E-Control
The very robust brass valve distinguishes the E-control. The
orientated design results in easy of handling. Only available in single
speed control.
Controls for JDN M-Series
DS Control
The operating air is connected to the hand control valve. A built-in pressure
regulator prevents overload to the hoist in case of inadmissibly high
pressure. The motor connection housing of the DS control includes an oiler
which automatically stops the oil flow when the hoist comes to a standstill.
An additional advantage: the oiler is situated directly around the motor. The
operating air immediately feeds to the motor when the hand lever is
actuated. The hand lever is spring loaded and returns automatically to the
zero position when released. This forced release serves also as an
emergency stop. The DS control is for two-hand operation and it is
available for all air hoists of the "B" and "M" series.
PS Control
The PS control is an alternative for the DS control, being a single hand use
controller for the M-series hoists.
Controls for JDN Air Hoists with Motor Trolley and JDN Monorail Hoists
For controlling JDN air hoists with motorised trolleys and JDN monorail hoists we recommend the four
button version E or F - Control. The rope control option is also available.
Controls for JDN Air Cranes
For controlling JDN air cranes the F-control is the most suitable due to its multi-function capability.
Operating convenience via Radio Control
To overcome excessive distances between operator and crane, or to remotely use hoisting equipment,
the JDN Radio Control offers a convenient and safe alternative to other control types. The JDN Radio
Control is also available in explosion proof design.
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
VITAL CHAIN BLOCKS
Vital is a Japanese brand which is globally recognised for their high quality products. Their range of chain blocks are suited for many applications in the mining, construction, industrial and automotive industry. They have proven to be an economical method to lift heavy loads with ease. The capacities vary from 0.5 tonne to 20 tonne and all chain blocks can be supplied with overload protection for added security of use.
Features
• Manufactured in Japan using optimum high quality steel which conforms to the strict JIS & ISO regulations.
• All Vital models are manufactured to comply with AS1418.2.
• Designed for long-term use while providing the lowest possible per-use cost.
• Can be supplied close coupled and extra close coupled to girder trolleys to alleviate headroom restrictions.
• All Vital chain blocks can be supplied with overload protection.
• Customised lift height are available upon request.
• Quality caged needle bearings on load sheave and thrust bearings on bottom hook.
• Hardened alloy steel load chain with embossed identification, marked as to the relevant standards.
• Load chain exceeds Australian Standards with 5:1 Safety Factor.
Specifications
*Vital chain blocks with customised lift heights are available
Dimensions (in mm)
MODEL 05VH5 10VH5 15VH5 20VH5 30VH5 50VH5 75VH5 90VH5 92VH5 93VH5
Stock Code VCB050 VCB100 VCB150 VCB200 VCB300 VCB500 VCB750 VCB910 VCB915 VCB920
Rated Capacity (tonne) 0.5 1.0 1.5 2.0 3.0 5.0 7.5 10.0 15.0 20.0
Standard Lift Height (m) 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0
Pull to lift load (kg) 25 33 34 34 35 39 41 41 41 x 2 41 x 2
Net Weight (kg) 8.6 11.5 13.8 21.6 23.0 41.0 60.5 78.0 150.0 190.0
MODEL 05VH5 10VH5 15VH5 20VH5 30VH5 50VH5 75VH5 90VH5 92VH5 93VH5 A 127 147 147 179 147 179 179 179 207 207
B 144 157 174 204 206 263 345 367 745 873
C 305 345 370 425 505 635 740 760 850 870
D 27 30 34 37 43 47 67 67 87 87
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
VITAL LEVER BLOCKS NR-2 SERIES
Vital is a Japanese brand which is globally recognised for their high quality products. The NR-series
lever blocks feature the “free-wheeling” braking system which enables fast and easy operation. There is
a minimum load requirement of 10% of the Working Load Limit to ensure that the braking system
remains operative and continues to support the load. These lever blocks are ideally suited for the
shipbuilding, construction, mining and power transmission industries.
Features
Manufactured in Japan using optimum high quality steel which conforms to
the strict JIS & ISO regulations.
All Vital models are manufactured to comply with AS1418.2.
One-touch operation for free chain adjustment.
Vital lever blocks can be supplied with overload protection for added security
of use (excluding 250kg and 500kg models).
The unique design of the bottom hook prevents slipping and ensures safe
operation.
Hardened alloy steel load chain with embossed identification, marked to the
relevant standards.
Load Chain Exceeds Australian Standards with 5:1 Safety Factor.
Minimum load requirement of up to 10% of the Working Load Limit to ensure
the operation of the braking system. E.g. a 1.5 tonne lever block requires a
minimum load of 150kg.
Light loading; not suitable for tandem operations. If one of the lever blocks
used in the tandem experiences an increase in the shared load and the
other is reduced below the minimum load, inoperative breaks may occur and
this could cause for the load to fall. For these applications we recommend
the Vital Lever Blocks VR-2 series
Specifications
*Vital lever blocks with customised lift heights are available.
Dimensions (in mm)
MODEL NR2-03 NR2-05 NR2-08 NR2-10 NR2-15 NR2-30 NR2-60 NR2-90
Stock Code VLB202 VLB205 VLB207 VLB210 VLB215 VLB230 VLB260 VLB290
Rated Capacity (tonne) 0.25 0.5 0.8 1.0 1.6 3.2 6.3 9.0
Standard Lift Height (m) 1.0 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Pull to lift load (kg) 30 34 21 23 27 38 39 40
Net Weight (kg) 1.9 3.5 6.0 7.2 9.8 16.6 27.0 47.3
Chain Size (mm) 4.0 5.0 5.6 6.3 7.1 9.0 9.0 9.0
No. of Falls 1 1 1 1 1 1 2 3
MODEL NR2-03 NR2-05 NR2-08 NR2-10 NR2-15 NR2-30 NR2-60 NR2-90
A 85 110 146 146 161 191 191 191
B 65 82 119 126 146 180 243 318
C 230 260 295 325 350 425 565 680
D 150 267 256 256 368 368 368 368
E 24 27 27 30 34 43 47 67
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
VITAL LEVER BLOCKS VR-2 SERIES
Vital is a Japanese brand which is globally recognised for their high quality products. The VR-series
lever blocks feature a “lock-in and lock-out” braking system which is the more traditional style with a free-
wheeling system requiring the disengagement of the gear drive mechanism which is impossible with any
load suspended on it. These lever blocks are ideally suited for the (underground) mining, aerospace and
energy industries.
Features
Manufactured in Japan using optimum high quality steel which
conforms to the strict JIS & ISO regulations.
All Vital models are manufactured to comply with AS1418.2.
Vital lever blocks can be supplied with overload protection for added
security of use (excluding 250kg and 500kg models).
The unique design of the bottom hook prevents slipping and ensures
safe operation.
Easy two-step operation to prevent accidental free-wheeling.
Hardened alloy steel load chain with embossed identification, marked
as to the relevant standards.
Load Chain Exceeds Australian Standards with 5:1 Safety Factor.
The Vital VR-2 series are suitable for tandem lifting applications.
Specifications
*Vital lever blocks with customised lift heights are available.
Dimensions (in mm)
MODEL VR2-08 VR2-15 VR2-30 VR2-60
Stock Code VLB107 VLB115 VLB130 VLB160
Rated Capacity (tonne) 0.8 1.6 3.2 6.3
Standard Lift Height (m) 1.5 1.5 1.5 1.5
Pull to lift load (kg) 15 18 38 39
Net Weight (kg) 6.9 9.7 16.3 26.7
Chain Size (mm) 6.3 7.1 9.0 9.0
No. of Falls 1 1 1 2
MODEL VR2-08 VR2-15 VR2-30 VR2-60
A 148 163 191 191
B 128 148 181 244
C 295 355 405 550
D 260 370 370 370
E 27 34 43 47
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
e
VITAL OVERLOAD LIMITER
Vital is a Japanese brand which is globally recognised for their high quality products. Their ranges of
chain & lever blocks are suited for many applications in the mining, construction, industrial and
automotive industry. One of the many unique features of the Vital products is the optional Overload
Limiter which ensures an added security of use by protecting the user and the lifting appliance from
dangerous overload situations.
Overload protection is achieved by adjusting the lock nut on the overload plate which is set and tested at
the Vital factory. This adjustment allows the tapered hub to slip on the change gear, by not allowing the
chain or lever block to be overloaded. The braking function is unaffected as the brake discs still lock as
normal.
Overload protection is available on all Vital Chain & Lever Block models, excluding the 250kg and 500kg
lever blocks. All Vital products are manufactured to comply with AS1418.2 and manufactured in Japan
using optimum high quality steel which conforms to the strict JIS & ISO regulations.
Overload Limiter Parts Diagram
NO. DESCRIPTION QUANTITY
1 Supporter 1
2 Ball Spring 1
3 Ball 1
4 Brake Disk B/OLL 1
5 Hard Wheel OLL 1
6 Brake Disk A/OLL 1
7 Pad Plate 1
8 Conic Spring 1
9 Washer 1
10 Nut 1
11 Cotter Pin OLL 1
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC CHAIN BLOCKS WITH OPTIONAL OVERLOAD PROTECTION
Pacific Chain Blocks feature better quality in a new compact design. The extensive range is suitable for
many applications in the mining, construction, industrial and automotive industry. A patented Overload
Limiting device is available for all sizes (except for 250kg capacity) to improve safety. These chain
blocks have it all; better quality, easy to use, improved safety and all of this with reduced cost.
Features
All Pacific models are manufactured to comply with AS1418.2.
High strength end stop with secondary end anchor for increased safety.
“T” type hooks for improved load holding integrity (except for the 250kg capacity).
Gear system design for reduced effort when lifting loads.
Includes a specially designed hand wheel to eliminate hand chain slippage and pocket wear.
Encapsulated needle bearings and side plate bearings for smoother operation.
Brake lockout bearing for security of braking mechanism.
Key internal components are CNC machined before being heat-treated and toughened.
Fitted with high quality European zinc plated Grade 80 load chain.
No aluminum content which ensures suitability for mining applications.
Overall better design and improved finish to prolong life expectancy.
All models available with a patented Overload Limiting device (except for the 250kg capacity).
Now available with a complimentary display stand when purchasing a product stock package. For more information, please contact your Pacific Hoists representative or refer to page 3.
Specifications
*Pacific chain blocks with customised lift heights are available
Dimensions (in mm)
CAPACITY 250 KG 500 KG 1
TONNE
1.5
TONNE
2
TONNE
3
TONNE
5
TONNE
10
TONNE
Stock Code PCB 301 302 303 306 313 316 318 319 323 326 333 336 353 356 359 360
Lift Height (m) 3 6 3 6 3 6 3 6 3 6 3 6 3 6 3 6
Test Load (kg) 375 750 1500 2250 3000 4500 7500 15000
Effort to lift full load (N) 190 210 285 325 355 340 400 540
No. of Falls 1 1 1 1 1 2 2 4
Hand Chain (mm x mm) Ø5 x 23.7
Hand Chain Drop (m) 2 5 2 5 2 5 2 5 2 5 2 5 2 5 2 5
Load Chain (mm x mm) Ø4 x 12 Ø5 x 15 Ø6.3 x 19 Ø7.1 x 21 Ø8 x 24 Ø7.1 x 21 Ø9 x 27 Ø9 x 27
Net Weight for 3m lift (kg) 6 9 12 14 20 23 39 75
Stock Code with O/L PCB 301L 302L 303L 306L 313L 316L 318L 319L 323L 326L 333L 336L 353L 356L 359L 360L
MODEL 250KG 500KG 1 TONNE 1.5 TONNE 2 TONNE 3 TONNE 6 TONNE 10 TONNE
A 106 128 142 158 175 158 183 195
B 68 75 76 80 88 80 90 95
C 108 130 150 170 185 220 225 355
D 280 280 330 360 385 510 615 810
E 20 22 26 29 35 37 43 47
F Ø18 Ø20 Ø25 Ø30 Ø33 Ø36 Ø43 Ø44
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC LEVER BLOCKS WITH OPTIONAL OVERLOAD PROTECTION
The extensive range of Pacific Lever Blocks feature superior quality at an affordable price. They are
suitable for applications in the mining, construction, transport and automotive industry. A patented
Overload Limiting device is available to improve safety (except for 250kg capacity).
Features
All Pacific models are manufactured to comply with AS1418.2.
“T” type hooks for improved load holding integrity (except for the 250kg capacity).
New design double pawl safety springs to eliminate sticking
New style cast hand wheel for added strength and durability
Encapsulated needle bearings and side plate bearings for smoother operation.
Brake lockout bearing for security of braking mechanism.
All Pacific lever blocks can be supplied with overload protection (except 250kg).
Key internal components are CNC machined before being heat-treated and toughened.
Fitted with high quality European zinc plated Grade 80 load chain.
No aluminum content which ensures suitability for mining applications.
Overall better design and improved finish to prolong life expectancy.
Now available with a complimentary display stand when purchasing a product stock package. For more information, please contact your Pacific Hoists representative or refer to page 3.
Specifications
*Pacific lever blocks with customised lift heights are available
Dimensions (in mm)
CAPACITY 250 KG 500 KG 800 KG 1.6
TONNE
3.2
TONNE
6.3
TONNE
Stock Code PLB302 PLB305 PLB308 PLB316 PLB332 PLB363
Lift Height (m) 1.5 1.5 1.5 1.5 1.5 1.5
Test Load (kg) 375 750 1200 2400 4800 9450
Effort to lift full load (N) 115 248 285 315 360 370
No. of Falls 1 1 1 1 1 2
Load Chain (mm x mm) Ø4 x 12 Ø5 x 15 Ø5.6 x 17 Ø7.1 x 21 Ø10 x 28 Ø10 x 28
Length of lever handle (D) (mm) 168 253 273 378 418 418
Net Weight for 1.5m lift (kg) 1.86 4.42 5.71 9.27 16.50 21.29
Stock Code with O/L N/A PLB305L PLB308L PLB316L PLB332L PLB363L
CAPACITY 250 KG 500 KG 800 KG 1.6 TONNE 3.2 TONNE 6.3 TONNE
A 100 143 147 173 200 200
B 70 85 87 99 112 112
C 86 118 132 145 198 230
D 235 310 340 400 520 640
E 168 253 273 378 418 418
F 20 22 26 29 37 43
G Ø18 Ø20 Ø25 Ø30 Ø36 Ø43
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC PRODUCT DISPLAY STAND
With the purchase of one of our product stock packages, you are entitled to a complimentary Pacific
Product Display Tripod Stand; made from quality steel. It features lockable castor wheels for ease of
movement and safety while on display. The Pacific Hoists signage includes a QR code for quick access
to product features, specifications and line drawings. The stand allows for the display of chain blocks,
lever blocks, trolleys and clamps.
Features
Tripod stand made from quality steel.
Inclusive of lockable castor wheel for ease of movement and safety
while on display.
This display stand is collapsible by unbolting the screws.
Pacific Hoists signage which includes a QR code for quick access to
product features, specifications and line drawings.
For the display of a variety of chain and lever blocks, trolleys and clamps.
Contact your Pacific Hoists representative to discuss your stock
requirements. The package must consist of Pacific GEN III chain
blocks or lever blocks, Pacific trolleys and clamps. An example of such
package can be 1x PCB303. 1x PCB313, 2x PCB313L, 2x PCB316L,
1x PLB302, 1x PLB308L, 1x PLB316L, 2x PGC310 and 2x PPT105.*
Specifications & Dimensions
PRODUCT CODE STAND
Height (m) 220
Width (m) 140
Depth (m) 140
Weight; excl. products (kg) 25
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
*The display stand is offered as part of this package for the sole purpose of display of products offered by Pacific Hoists.
PACIFIC GIRDER CLAMPS
Pacific Girder Clamps are used to safely suspend loads of many descriptions from girders (I-beams).
Manual, Electric and Air hoist installations are examples of their wide capability of usage.
Features
All Pacific girder clamps are manufactured to comply with AS4991.
Quick and easy to install and reposition makes them ideal for maintenance tasks
Jaws clamp over girder flanges.
Also suitable for lifting I-beams.
Can be used at up to 45 degree angle with
a 50% reduction in capacity.
Specifications
Dimensions (in mm)
MODEL PGC310 PGC320 PGC330 PGC350 PGC390
Stock Code PGC310 PGC320 PGC330 PGC350 PGC390
Rated Capacity (kg) 1000 2000 3000 5000 10,000
Beam width range (mm) 80 - 245 80 - 245 90 - 310 90 - 310 90 - 320
Net Weight (kg) 3.5 4.5 9.5 11.0 16.0
MODEL PGC310 PGC320 PGC330 PGC350 PGC390
A 270 270 365 365 365
B 375 375 520 520 520
C 66 74 103 111 120
D 4 6 8 10 12
E 25 25 45 45 50
F 165 165 225 225 230
G 210 210 258 258 280
H 50.5 - 82 50.5 - 82 80.5 - 126 80.5 - 126 94.5 - 138
I 12 12 19 19 21
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC PIPE TROLLEY
The Pacific Pipe Trolley is compact and lightweight, a general purpose unit and designed to suit 60mm
O/S diameter pipe.
Features
The Pacific pipe trolley is manufactured
to comply with AS4991.
Designed to suit 60mm outside diameter
pipe
Compact and lightweight with powder
coated finish.
Specifications
MODEL PPT203
Stock Code PPT203
Rated Capacity (kg) 300
Pipe Diameter (mm) 60
Net Weight (kg) 2.5
Dimensions (in mm)
MODEL PPT203
A 147.5
B 160
C 22
D 68
E 160
F 60
G 17
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC SERIES 1 GIRDER TROLLEYS
Pacific Series 1 Girder Trolleys feature a strongly constructed, fully adjustable trolley which is designed
to fit the flanges of both tapered and parallel beams. They are available as push or geared variety and
comply with all relevant Australian Standards.
Features
All Pacific girder trolleys are manufactured to
comply with AS1418.2.
Choose from either push or hand-geared travel.
Twin pin configuration provides closer
headroom than single pin variety
Available to suit larger beam widths on request
Fitted with anti-drop plates for improved safety
and compliance.
Can be supplied close coupled to suit most Pacific hoists.
Specifications
Pacific Series 1 Girder Trolleys (PUSH)
*Additional beam width available on request.
Pacific Series 1 Girder Trolleys (GEARED)
*Additional beam width available on request.
Dimensions (in mm)
Pacific Series 1 Girder Trolleys (PUSH)
MODEL PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
Stock Code PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
Rated Capacity (kg) 500 1000 2000 3000 5000 10000
Beam width (mm) 62 - 172 76 - 204 90 - 216 126 - 210 126 - 210 125 – 310
Min. curve radius (m) 0.8 1.0 1.5 1.7 1.7 2.7
Net Weight (kg) 6.06 10.88 19.12 34.96 36.30 118.0
Gross Weight (kg) 6.4 11.32 19.88 36.22 36.70 133.0
MODEL PGT110 PGT120 PGT130 PGT150 PGT160
Stock Code PGT110 PGT120 PGT130 PGT150 PGT160
Rated Capacity (kg) 1000 2000 3000 5000 10,000
Beam width (mm) 76 - 204 90 - 216 126 - 210 126 - 210 125 – 310
Min. curve radius (m) 1.0 1.5 1.7 1.7 2.7
Net Weight (kg) 15.08 24.44 40.30 42.10 131.0
Gross Weight (kg) 15.75 25.32 41.64 43.50 148.0
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Pacific Series 1 Girder Trolleys (GEARED)
MODEL PPT105 PPT110 PPT120 PPT130 PPT150 PPT160
A 179 217 281 315 315 399
B 131 151 162 176 179 253.5
C 132 153 164 176 179 253.5
D 68 76 106.5 123 123 167
E 51.5 69 83 125.5 125.5 172
MODEL PGT110 PGT120 PGT130 PGT150 PGT160
A 238 303 332 332 399
B 206 212.5 210.5 210.5 335.5
C 153 164 176 179 253.5
D 87 117.5 131 131 167
E 69 83 125.5 125.5 172
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC GIRDER TROLLEYS
Pacific Girder Trolleys feature high quality construction for an economical price. They are available in
either a push or geared variety and comply with all relevant Australian Standards.
Features
All Pacific girder trolleys are manufactured to
comply with AS1418.2.
Fully adjustable to suit various beam widths.
Fitted with anti-drop plates for improved safety
and compliance.
High-grade, fully sealed bearings for
maintenance free extended life.
Available with either push or hand geared travel.
Anti-drop plates as standard for improved safety
and compliance.
Specifications
Pacific Girder Trolleys (PUSH)
Pacific Girder Trolleys (GEARED)
Dimensions (in mm)
Pacific Girder Trolleys (PUSH)
MODEL PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
Stock Code PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
Rated Capacity (kg) 500 1000 2000 3000 5000 10000
Pin Configuration Single Single Single Single Single Twin
Min. radius of curve (m) 0.8 1.0 1.1 1.3 1.4 2.0
Net Weight (kg) 6.5 10.5 17.5 27.0 41.0 86.0
MODEL PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
Stock Code PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
Rated Capacity (kg) 500 1000 2000 3000 5000 10000
Pin Configuration Single Single Single Single Single Twin
Min. radius of curve (m) 0.8 1.0 1.1 1.3 1.4 2.0
Net Weight (kg) 10.5 14.5 21.5 31.0 46.0 91.0
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Pacific Girder Trolleys (GEARED)
MODEL PPT305 PPT310 PPT320 PPT330 PPT350 PPT360
A 223 270 300 356 405 485
B 188 224 261 308 354 395
C 32 40 52 62 75 110
D 24 30 38 40 50 70
E 244 310 327 342 354 480
F 50 - 152 64 - 203 88 - 203 100 - 203 114 – 203 124 – 305
G 1.5 - 3
H 105 126.5 146 169 197 188
I 31 38 36 40 42 40
MODEL PGT305 PGT310 PGT320 PGT330 PGT350 PGT360
A 223 270 300 356 405 485
B 188 224 261 308 354 395
C 32 40 52 62 75 110
D 24 30 38 40 50 70
E 273 341 349 362 374 501
F 50 - 152 64 - 203 88 - 203 100 - 203 114 – 203 124 – 305
G 1.5 – 3
H 105 126.5 146 169 197 188
I 31 38 36 40 42 40
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC SINGLE FLANGE TROLLEY WHEELS
Features
The Pacific Single Flange Trolley Wheels are ideally suited for general machinery production, crane building, platforms, carriages and rail systems. They are designed to suit both parallel and tapered flanges and are available in different capacities from 500 kg to 10 tonne.
• CNC machined from high quality 45# steel.
• Designed to suit both parallel and tapered flanges.
• Fully sealed ball bearings.
• Inclusive of dust cap and circlip.
• Supplied complete; with galvanised axle and nut.
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to
be used for lifting or lowering persons.
MODEL PTW005 PTW010 PTW020 PTW030 PTW050 PTW100
Rated Capacity on 4 Wheels 500 kg 1 tonne 2 tonne 3 tonne 5 tonne 10 tonne
Rated Capacity per Wheel 125 kg 250 kg 500 kg 750 kg 1.25 tonne 2.5 tonne
Weight (kg) 0.7 1 2.5 3.7 6.2 12.3
Specifications
Dimensions (in mm)
MODEL PTW005 PTW010 PTW020 PTW030 PTW050 PTW100
ØA 62 70 100 114 140 175
ØB 92 100 136 160 190 230
C 9 9 11 13 15 12
D 18 20 24 28 34 53
E 2 2 2 3 3 3.2
F M16 M20 M24 M30 M36 M48
G 30 35 45 50 60 70
CROSBYIP LIFTING CLAMPS
The CrosbyIP range of lifting clamps are manufactured from high quality steel which has been forged,
quenched, tempered and heat-treated to guarantee the safety and durability required by industrial
applications. All clamps have been ergonomically designed to be user friendly (smaller, lighter and more
compact), while not sacrificing strength and durability.
The CrosbyIP lifting clamps are available in a variety of models to allow the lifting and transferring of
steel plates and other materials in a wide variety of industries. These industries include ship building,
offshore, aircraft, construction and metal-processing.
Features
All models are manufactured to comply with
AS4991.
Manufactured by a market world leader.
All clamps have been subject to rigorous quality
control for maximum reliability.
All products are supplied with a test certificate
and instruction manual.
All vertical plate clamps may be used to lift
materials with a hardness up to 345 Brinell
(37Rc).
IPBC Horizontal Lifting Clamp
IPU10 Vertical Plate Clamp
IPNM10 Non Marring Vertical Plate
Specifications
CLAMP TYPE MODEL RATED
CAPACITY (KG) JAW (MM)
STOCK
CODE
Universal Vertical Plate
This model is based on the IP10 lifting
clamp but is equipped with a universal
(hinged) hoisting eye. This makes it
possible to lift loads from any given
direction. The IPU10 clamp is also very
useful in applications where larger plates
are to be lifted with two clamps in
combination with a two-legged chain.
0.5-IPU10 500 0 – 16 CLP005
1-IPU10 1000 0 – 20 CLP010
2-IPU10 2000 0 – 35 CLP020
3-IPU10 3000 0 – 40 CLP030
4.5-IPU10 4500 0 – 40 CLP040
6-IPU10 6000 0 – 50 CLP060
9-IPU10 9000 0 – 50 CLP070
9-IPU10/J 9000 50 – 100 CLP071
12-IPU10 12000 0 – 54 CLP080
12-IPU10/J 12000 54 – 108 CLP081
Vertical Plate
The IP10 clamps may be used to lift,
turn by 180º and vertically transport
steel plates and construction elements.
0.5-IP10 500 0 – 16 CLP014
1-IP10 1000 0 – 20 CLP012
2-IP10 2000 0 – 35 CLP022
3-IP10 3000 0 – 40 CLP032
4.5-IP10 4500 0 – 40 CLP042
6-IP10 6000 0 – 50 CLP062
9-IP10 9000 0 – 50 CLP075
9-IP10/J 9000 50 – 100 CLP076
12-IP10 12000 0 – 54 CLP085
12-IP10/J 12000 54 – 108 CLP086
Non Marring Vertical Plate
1-IPNM10 1000 0 – 20 CLP410
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Specifications (Continued)
CLAMP TYPE MODEL RATED
CAPACITY (KG) JAW (MM)
STOCK
CODE
Horizontal Plate
These clamps are suitable for the lifting
and transfer in horizontal position of
non-sagging steel plates. The clamp is
equipped with a handle for simple and
easy placement onto the plate. These
clamps must be used in pairs or more.
Available in capacities of 2 to 12 tonne.
All clamps are individually proof tested
to 2 times the rated capacity with
certification.
2 IPH10E 2000 0 – 60 CLP516
3 IPH10E 3000 0 - 60 CLP531
3 IPH10JE 3000 60 - 120 CLP536
4.5 IPHTONZ 4500 0 - 60 CLP545
6 IPH10E 6000 0 - 60 CLP561
6 IPH10JE 6000 60 - 120 CLP571
9 IPH10E 9000 0 - 60 CLP091
9 IPH10JE 9000 60 - 120 CLP096
12IPH10E 12000 0 - 60 -
12IPH10JE 12000 60 - 120 -
Horizontal Lifting Clamp (Manual pre-tensioning)
1-IPBC 1000 0 – 20 CLP100
2-IPBC 2000 0 – 25 CLP200
Vertical Drum
The IPVK drum clamp is for vertical lift and
transfer. Automatically locks on drum and
can be used alone or in pairs. The IPDV
drum is for vertical lift and transfer. Allows
drum to remain in an upright position
during the lift and transfer using one clamp.
0.5-IPVK 500 17 CLP900
0.5-IPDV 500 300 CLP910
Horizontal Plate (with locking device)
1.5-IPHGZ 1500 0 – 25 CLP115
3-IPHGZ 3000 0 – 40 CLP130
Horizontal Pipe Hook (pair)
2-IPP 2000 200 CLP320
Beam Clamp (with locking device)
1.5-IPBHZ 1500 0 – 25 CLP580
3-IPBHZ 3000 0 – 40 CLP585
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
ELECTRICAL FEED SYSTEMS
Pacific Hoists offer a range of electrical feed systems to supply power to travelling hoists, cranes and other
machinery.
AKAPP Multi Conductor Systems
AKAPP delivers compact, reliable and secure power supply systems for
cranes, hoists and trolleys. The installation of these systems is suitable for
both inside and outside, high and low temperatures and for extreme (weather)
conditions. The unique double-sided flexible rubber seal provides protection
against dust, damp and corrosive environments. The rail system accepts up to
seven conductors in continuous lengths, up to 300m.
Metreel Festoon System
The Metreel flatform cable festoon system is designed to support one or more flatform
cables of various sizes. The “C” track provides sag free support of power and pendent
cables, air lines etc. to electric hoists, air hoists, power tools, air tools in a wide variety
of applications.
Roller Hanger System
This roller hanger system is an economical solution for powering an
electric hoist which is easy to install and requires minimal
maintenance. The hangers accept a round form cable and operate
along a fixed wire.
Zeca Cable Reels
Zeca cable reels are lightweight and provide a safe and economical method
of supplying power to moving machinery. They are designed for outdoor and
indoor installations and require minimal assembly. The reels are spring
loaded; allowing the cable to be pulled out and to automatically recover as
the machine moves back and forward. A large range of cable lengths are
available.
Specifications
*Customised Track to Track Support available upon request
ITEM DESCRIPTION STOCK CODE
CATENARY CABLE & STRAINER WIRE SYSTEM
Pacific Cable Trolleys N/A CAB001
3mm Galv Strainer Wire N/A 400002
Round Cable 1.5mm 4 core & 10 amps CAB400
Round Cable 1.5mm 3 core x 10 amps CAB300
CABLE REELS (RUN ON EITHER SINGLE OR THREE-PHASE)
Zeca (6179PRC) with 15m 4 x 2.5mm² cable 10 amps ZEC120
Zeca (6521PRC) with 15m 4 x 2.5mm² cable 20 amps ZEC110
Zeca (6181PRC) with 15m 4 x 1.5mm² cable 10 amps ZEC130
Zeca (5821XF) with 5.5m 4 x 2.5mm² cable 10 amps ZEC140
Zeca (5823XF) with 8m 4 x 1.5mm² cable 10 amps ZEC150
FLATFORM CABLE
4 core x 2.5mm² PVC 25 amps CAB425
13 core x 1.5mm² PVC 20 amps CAB470
PENDANT CABLE - DANGLEFLEX
5 core x 1.25mm² PVC 10 amps CAB155
8 core x 1.5mm² PVC 20 amps CAB108
12 core x 1.25mm² PVC 20 amps CAB112
16 core x 1.5mm² PVC 20 amps CAB115
25 core x 1.5mm² PVC 20 amps CAB125
TYPE 100
Track – 5m length 100/5 MET100
Splice Joint 1103 MET150
Support Hanger Bracket 102 MET105
Track to Track Support (500mm standard*) T100 MET103
Girder Clip TB100 MET140
End Stop (steel) 100P MET110
End Clamp (steel) 100/137E MET135
Flat Cable Trolley (steel) 100/137 MET115
Flat Cable Trolley (plastic) 100/50N MET120
Towing Attachment (steel) 100TA/S MET125
Towing Attachment (plastic) 100TA/N MET130
Suspension Trolley (steel) 100/237ST MET165
Roving Pendant Box Plug / Socket MPS100/16 MET155
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC MY-T-LIFT
The Pacific My-T-Lift is the perfect solution for the safe handling of heavy loads, up to 300kg. This 360°
telescopic job crane is designed for single handed operation and can be mounted on trucks, trailers,
pontoons and similar structures. It has the option of a manual winch which includes a 6 meters rope or a
12 or 24 volt electric winch, featuring a rope length of 12 meters.
Due to its design, the My-T-Lift has the capability to allow accurate placement of heavy loads, even in
confined space.
This product is made from high quality durable steel and has the option to fold down when not in use.
Features
360° manual radial slew; with slipper bearing thrust
race for ease of slewing motion.
Rugged structure with low maintenance powder
coated finish.
Folds down when not in use.
Allows accurate placement of heavy loads, even in
confined space.
Available with manual winch, 12 or 24 volt electric
winch.
Optional drum lifting sling available.
Specifications
Dimensions (in mm)
Pacific My-T-Lift
MODEL MYT300B MYT300M MYT300E MYT300F
Stock Code MYT300 MYT318 MYT312 MYT324
Rated Capacity (kg) 300 300 300 300
Rope Length (m) Nil 6 12 12
Winch Type Nil Manual brake 12V DC 24V DC
Net Weight (kg) 68 78 83 83
MODEL MYT300 BASE PLATE
A 1790 455
B 1490 379
C 1290 195
D 1110 70
E 920 123
F 1730 450
G 1330 -
H 2030 -
I 1510 -
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
PACIFIC MAGNETIC LIFTERS
Pacific Magnetic Lifters can be used in various industries for the lifting and moving of steel, engine parts,
semi-manufactured goods and moulds, Due to its magnetic force, there is no need to use slings, clamps
or other holding devices. This will eliminate the chance of damaging the lifted materials.
Features
The magnetic lifter features a breakaway force 3.5
times greater than the working load limit.
Weight capacities are available from 100kg to
6000kg.
No electricity needed which will increase product
safety. Once operated there is less than 1%
residual magnetism.
The simple switch and safety button design allows
for one handed operation.
Use of plate with high-carbon content will reduce
the absorbability to less than 50% of rated capacity.
Use of plate with high carbon content is not
recommended.
Specifications
Rate of Reduction Graph
MODEL PML-1 PML-3 PML-6 PML-10 PML-20 PML-30 PML-60
Stock Code MAG010 MAG030 MAG060 MAG100 MAG200 MAG300 MAG600
Rated Capacity (kg) 100 300 600 1000 2000 3000 6000
Cylindrical Carrying Capacity (kg) 50 150 300 500 800 1200 1800
Max. Break-away Force (kg) 350 1050 2100 3500 7000 10500 21000
Net Weight (kg) 3 10 24 50 125 240 440
MODEL PML-1 PML-3 PML-6 PML-10 PML-20 PML-30 PML-60
Rated Capacity (kg) 100 300 600 1000 2000 3000 6000
Suitable Thickness of Plate (mm) > 25 > 35 > 40 > 50 > 60 > 80 > 120
Plate Material ≤45# steel ≤45# steel ≤45# steel ≤45# steel ≤45# steel ≤45# steel ≤45# steel
Carbon Content Low Low Low Low Low Low Low
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
Dimensions (in mm)
MODEL PML-1 PML-3 PML-6 PML-10 PML-20 PML-30 PML-60
A 67 91 117 163 212 261 355
B 62 92 122 176 234 286 430
C 92 162 232 258 378 458 600
D 126 155 196 285 426 521
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
IKUSI REMOTE CONTROLS
Pacific Electric Hoists and Hitachi Electric Hoists are available with the following Ikusi remotes.
Transmitters: T70 1
High-sensitivity two-step push button
Multiband radio with Full-Duplex communication
High customisable
LCD display optional
External removable EEPROM SIM module
Easy and fast maintenance
High resistance to impacts
Frequency management
Battery power pack included
Model T70 1
Stock Code RRC007 - RRC008
Stop function Cat. 3 - PLd
Ingress protection IP65/NEMA4
Anti condensation system Na
Frequency band Multiband (400 – 930 MHz)
Main mechanisms (max. #) Pushbutton (6)
Auxillary mechanisms 3 position selector switch
Removable EEPROM External
Battery model BT06K
Battery life 10h
Operating temperature Range -20C + 70C (-4F + 158F)
Weight (with battery) grams 460
Harness Hand strap
Display 2x12 Char LCD
Range limiter yes
Associated receivers RO6/ R13/ R70
Functions of RRC007 Raise, lower, east, west, E/stop
Functions of RRC008 Raise, lower, east, west, north,
south, E/stop
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.
RRC007/RRC008 & Battery Pack
Receivers: R06
Multiband radio with Full-Duplex communication
External LEDs for troubleshooting
Highly field-customisable
Removable EEPROM SIM module
Frequencies management against interferences
STOP: PLd, Category 3 according to EN ISO 13849-1
Easy and fast maintenance
Multi-feedback capability
6 digital outputs
Model R06
Stop function Cat. 3 - PLd
Ingress protection IP65/NEMA4
Frequency band Multiband (400 – 930 MHz)
AC power supply 24, 48 – 240 VAC or 12VDC
Antenna Internal
Removable EEPROM Internal
Signaling External
ON/ OFF outputs (max.) 6
ON/ OFF inputs (max.) 4
Analogue inputs (max.) 1
Max. output current 6A
Working temperature range -20C + 70C (-4F + 158F)
Weight (g) 640
Dimensions ( LxWxH mm) 151 x 129 x 61
Cable connection Yes
Associated transmitters T70/1, T70/1ATEX, IK2
The information shown is to be used as a guide only. Specifications are subject to change without notice.
The information shown is to be used as a guide only. Specifications are subject to change without notice. All materials handling or lifting jobs should be assessed individually. Pacific Hoists products are NOT to be used for
lifting or lowering persons.