1
Corrigendum 1: For Enquiry No. : No. : GPK /Store/inst purchase/EED/2019-20/ 140 Date:04 /01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of Machinery and
Equipment during 2019-20 . Kindly note the updates shown in column no 5 below and do needful. The estimated cost shown in column 5 is inclusive of all taxes , GST, transportation , handling, etc.
(inclusive of all).
Sr.
No.
Name of the item with specification Quantity
required
Estimated
Cost per item
in Rs. Name of the item Specification
1
HV Test kit for motors
upto 400 volt
Air cooled transformer for upto 10kV and
Transformer Oil cooled for 25kV AC.
· Output volt and Amp measurement
with digital panel meters.
Add on- extension unit for DC outputs.
· P.B. operated contactor and zero start
H.V. “ ON” interlock. Overload alarm and
trip facility.
· Separate control unit and H.V. unit
01 15000
2 Dead weight tester:-
Accuracy better than 0.015% of reading
(0.008% available on request)
Over all range: 0.2-2000 bar, 10-30000
psi, 0.2-2000 kg/cm²
Various pressure units available: bar,
kg/cm², psi, MPa, kPa
In dual piston models PCU changeover
from LP to HP automatically [ Except
model above 1000 bar]
Pressure generated by a ram screw
Pressure calibration over a wide range
allowed in Dual Piston Models
Operating fluid: Hydraulic oil & distilled
water (depends on model chosen)
01 3000
3
Air Purge Level
Measurement:-
Level Tank : Transparent, () 150mm x (H)
600mm
Pneumatic Tubing : 1/4.” PU
Level Indicator : Pressure gauge calibrated in
mmwc.
Air Regulator : 1/4” air regulating valve, leak
proof.
01 15000
4
Variable RLC Load
Bank
Power-250-440 VAC,Freq. 50 Hz, current-
5-20A ,single phase& 3 phase 01
48000
5
Thyrite type of lightning
arrester
Voltage rating:11-66kv
Current rating:200-800amp
Housing made of porcelain or polymer
01 8000
Principal
Govt. Polytechnic, Khamgaon
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions
issued.
3) Head of Electrical Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
3
1
Corrigendum 1 No. : GPK /Store/inst purchase/ETX/2019-20/26 Date:02 /01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of
Machinery and Equipment and kindly note the updates shown in column no 5 and do needful
accordingly. The estimated cost shown in column 5 is inclusive of all taxes , GST, transportation
, handling, etc. (inclusive of all).
Sr. No.
Name of the item with specification Quantity required
Estimated
Cost per
item in Rs. Name of the
item Specification
1 2 3 4 5
1.
Development
Board With
ATMEGA 16
Microcontroller: ATMEGA16 with 11.0592MHz
crystal
Power: 7 to 15V, AC or DC, Heat sink on 7805 for
better current rating with Reverse polarity protection
Boot, Reset and Power switches,RS232 serial interface,
10 pin FRC connectors and soldering pads on all ports,
Compatible with General purpose prototyping board for
development board for stackable design and
Application examples with documentation CD
02 10000
2.
Transient
Analysis Of
RC/RL Circuit
Trainer Kit
Experiments:-1-Study the Transient Response of a
series RC circuit and Understand the time constant
concept with DC power supply
2-Study the Transient Response of a series RL circuit
and Understand the time constant concept with DC
power supply
3-Study of Transient Response of RC/RL circuit with
signal generator
Setup Includes :-
>Experiment Trainer Board that Contains:-
1.Power Supply : 5 V DC 2.Signal Generator : 100 Hz
3.Various test point >Connecting Patch Cords >Product
tutorials
02 5000
3.
Transient
Analysis Of
RLC Circuit
Trainer Kit
Experiments:-
Study the transient response of series of RLC
circuit
with TTL for under damped, critically and over
damped cases
Setup Includes :-
>Experiment Trainer Board that
Contains:-
02 5000
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
1.Signal Generator : 100 Hz
2.Potentiometer :
100 K
3.Various test
point
>Connecting Patch Cords
>Product Tutorial
4.
Solar PV
Characterization
Kit
Trainer kit for Identifying and measuring the
parameters of a solar PV module in LAB,
Series and Parallel Connection of PV modules,
Estimating the effect of sun tracking on energy
generation by solar PV modules,
Voltage :12V
Power:50 watt
With user manual
02 10000
5.
Trainer Kit For
Anemometer
For Wind Speed
Measurement
Start wind speed (m/s) 0.4 – 0.8
Effective measurement range 0-30m/s
Transmission distance (m) < 700
Max Wind Speed 70m/s
01 5000
6.
Synchro As
Error Detector
Kit
Synchro As Error Detector Kit
01 5000
7.
Trainer Kit For
Transformer
Coupled
Amplifier Using
Transistor
On board test points to observe Input and output signals
On board schematic diagram
Flexibility of making circuit connections
Lightweight & compact
product tutorial
01 5000
8.
Trainer Kit To
Verify Nortons
And Theveniens
Theorem
On board schematic diagram
Flexibility of making circuit connections
Provision of applying input and taking output with
External power supply to trainer
02 5000
9.
Trainer Kit To
Determine
Z,Y,ABCD
Parameters Of
Transmission
Line
On board schematic diagram
Flexibility of making circuit connections
Provision of applying input and taking output with
External power supply to trainer
02 10000
10.
Trainer Kit To
Verify KVL
And KCL
Experiments:-
1-Verification of Kirchhoff's current law
2-Verification of Kirchhoff's voltage law
Setup Includes :-
>Experiment Trainer Board that Contains:-
1.Power Supply : + 12 V DC
2.Digital Ammeter : 2 µA to 200 mA
3.Various test point
>Connecting Patch Cords
>Product Tutorial
02 10000
3
Sr. No.
Name of the item with specification Quantity required
Estimated
Cost per
item in Rs. Name of the
item Specification
1 2 3 4 5
11.
Data Acquisition
Card
NV63X series DAQ are useful for sensing and
controlling Analog and Digital signals of any process
control application. For ease of connection theyhave
screw terminals. All can change the operation of
particular pins as per requirements.They are available
with either a USB interface
Data Card Includes following specifications:-
1.Digital inputs : 16
2.Digital Outputs : 16
02 15000
12.
PID Controller
Trainer Kit
Square and triangular wave with variable frequency for
testing PID Proportional, Integral and Derivative
functions can be checked on same board, Variable DC
for set point, In built power supply
Built-in 3½ DVM for DC measurement
Manual describing working of along with detailed
experiment descriptions
02 10000
13.
Trainer Kit For
Speed Control
Of AC/DC
Motor With
VFD
Demonstration type trainer
02 12000
14.
DTH System
Trainer
Compact design
Comprehensive learning solution on DTH
Functional block diagram indicated on main board
Manual & Remote Control operation Composite Video
output and RF output
Fault creation and diagnosis
Online Product Tutorials
02 20000
Principal,
Govt. Polytechnic, Khamgaon
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions
issued.
3) Head of Electronics Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
1
Corrigendum 1 No. : GPK /Store/inst purchase/ETX/2019-20/23 Date:02 /01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of
Machinery and Equipment and kindly note the updates shown in column no 5 , Name of
item at S.N. 3 & 4 below and do needful accordingly. The estimated cost shown in column 5 is
inclusive of all taxes , GST, transportation , handling, etc. (inclusive of all).
Sr. No.
Name of the item with specification Quantity required
Estimated
Cost per
item in Rs. Name of the
item Specification
1 2 3 4 5
1.
PA System
Superior quality 100W high power PA System
Superior quality 100W high power PA System 5 Mic
and 2 Aux Inputs & 3 Speaker output (4 Ω/8 Ω/16 Ω)
Bass and Treble tone controls with Master control.
Complete block diagram of a PA system on-board
01 45000
2.
Trainer kit for
FDM and TDM
Demultiplexing
Trainer kit shall demonstrate principle of FDM and
TDM multiplexing and DE multiplexing
02 10000
3.
Trainer kit for
UJT
Characteristics
Trainer kit suitable to plot V I characteristic of UJT
with input points for application of bias voltages
(without on board DC supply) and various Test points.
On Board Schematic Diagram: Yes
Number Of Led Indicators Available To Indicate
Power Input:1
Provision Of On-Board Knob For Adjusting The
Voltage: Yes
Accessories
Patch Cords For Interconnection, Power Cords For Ac
Supply With facility to use as Relaxation Oscillator
02 4000
4.
Trainer Kit For
Negative
Feedback
Amplifier using
transistor
Trainer kit suitable to plot the frequency response with
and without Voltage series feedback, Voltage shunt,
Current series and current shunt feedback. UJT with
input points for application of bias voltage and various
test points.
02 5000
5.
DC Position
Control System
Trainer
Demonstration type trainer to conduct
1.Operation of the position control system for different
values of the forward gain to angular position
commands
2.Step response studies for various values of forward
gain With following features:
Position control of a 12V, 1A d.c. gear motor (50 rpm)
Provision for positive and negative tachogenerator
feedback Tacho constant: 2V/1000 rpm approximately
Calibrated dials for reference and output position:
resolution 1° Servo-potentiometers with full 360°
02 10000
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
rotation
μP based waveform capture/display card
Built-in 3½ digit DVM for signal measurements
Built-in step signal and IC regulated power supplies for
electronic circuits
Separate unit for motor in a see-through cabinet
220V±10%, 50Hz mains operation
Literature and patch cords included
Essential accessories - a CRO
6.
Trainer Kit For
Ic 723 Voltage
Regulator
Trainer kit suitable to study how the IC 723 can be
used as variable voltage regulator in low/high mode.
Measure the line and load regulation. Inbuilt
unregulated DC input and various test points.
01 3000
7.
Digital And
Analog IC
Tester
ANALOG & DIGITAL IC TESTER with analog IC
testing facility up to 16 pin IC and digital IC up to 40
pins
01 20000
8.
Trainer Kit For
4-Bit Counter
Using Flip-Flop
Experiments:-
1- Study of 4- bit synchronous up counter
2- Study of 4- bit asynchronous up/ down counter
Setup Including :-
>Experiment Trainer Board that Contains:-
1.Logic level : + 5V High (logic 1)
: 0 V Low (logic 0)
2.LED Indicate High and Low Level
3.Various test point
>5 Volts DC adaptor external
>Connecting Patch Cords
>With User Manual
01 5000
9.
Trainer Kit
Class B Push
Pull Amplifier
Using BJT
On board circuit to study class-b push pull power
amplifier With Points For Input And Test
ON/OFF switch and LED for power indication.
All interconnections are using 2mm banana Patch cords
with User manual and patch cords
Enclosed in a wooden/plastic box
02 5000
10. LCR Q Meter Standard equipment for measuring of inductance,
capacitance, resistance values and Q factor. 01 20000
11.
Potentiometers
As An Error
Detector
With two number of potentiometers and points for
connecting external power supply and measurement,
facility for rotational measurement.
02 5000
12.
Water Level
Measurement
Trainer Kit
Capacitive Transducer Precise Signal conditioning
Self-contained and easy to operate Data acquisition
using USB Sensitive, Linear, Stable & Accurate
Functional blocks indicated on board mimic On board
Digital Voltmeter On board Indicators; Buzzer & LED
02 12000
13.
Colour Pattern
Generator
Standard & Stable colour composite video signal
Auto generated composite video signal 5 Standard
patterns vertical bar, horizontal
bar, circle, white, decoder one at a time
01 12000
3
14.
SCADA System
For Educational
Purpose
SCADA system with programming tool for educational
purpose 01 70000
Principal,
Govt. Polytechnic, Khamgaon
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions
issued.
3) Head of Electronics Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
1
Corrigendum 1: For Enquiry No.No. : GPK /Store/inst purchase/APM/2019-20/ 24 Date:02/01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of Machinery and
Equipment during 2019-20 . Kindly note the updates shown in column no 5 below and do needful. The
estimated cost shown in column 5 is inclusive of all taxes , GST, transportation , handling, etc. (inclusive of
all).
Sr.
No.
Name of the item specification Quantity
required
Estimated Cost
per item in Rs.
1 Cover Gauge
Concrete thickness gauge model of CTG-2
(Concrete Thickness Gauge) Battery Powered-
ASTM standard Frequency Resolution 10Hz,
Thickness range 81 mm to 50.8cm in standard
mode.
1 8000
2 Crack detection
microscope
Magnification = x35, measuring range 4 mm ,
division = 0.002mm, weight including battery
and box = 560gm, box
dimension=150x100x50mm .
1 50000
3 Half-cell
potentiometer
Voltage 2230, electric power source frequency
50Hz, corrosion monitoring technique standardize by ASTM
1 30000
4 Extensometer
With least count 0.01mm, max. extension 25mm
with single dial / gauge / digital display suitable
for various gauge length.
1 44000
Principal,
Govt. Polytechnic, Khamgaon.
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions
issued.
3) Head of Electronics Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
1
Corrigendum 1: For Enquiry No.No. : GPK /Store/inst purchase/CED/2019-20/20 Date: 02/01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of Machinery and
Equipment during 2019-20 . Kindly note the updates shown in column no 5 ,Quantity required for S.N. 3
below and do needful. The estimated cost shown in column 5 is inclusive of all taxes , GST, transportation ,
handling, etc. (inclusive of all).
Sr.
No.
Name of the
item
specification Quantity
required
Estimated Cost
per item in Rs.
1 Plane Table
with
accessories
Planed Table: Well-seasoned good quality drawing
board made of pine or teak wood having smooth, plane
finish, on its top and fitted with ball socket arrangement
or a levelling head varying in size from 75cm x 60cm x
1.50cm or 60cm x 50cm x 1.50cm or 50cm x 40cm
x1.50cm.
Plane Alidade: A plane alidade Metallic (Brass or Gun
Metal) or good quality wooden rule with a fine beveled
edge.
Spirit Level: Tabular Level, which can be placed in two
perpendicular positions.
Trough Compass: Usually it is 15cm long and provided
with magnetic needle to facilitate orientation of the plane
table and to mark the north direction.
U-Frame/Plumbing Fork: It is hair-pin shape brass frame
having two arms of equal length. One end of frame is
pointed; the end of the frame carries a plumb bob.
Clamp: Steel or Plastic drawing sheet clamps of suitable
size.
1 4500
2 Thickness
Gauge
Variuos sizes
Thickness Gauge as per IS 2386, Part I, 1963 1 1500
3 Length Gauge
Various sizes Length Gauge as per IS 2386, Part I, 1963 3
1200
4 Orthotolodine
Test Kit
Orthotolodine Test Rig: Free Chlorine Measurement
Type: Colorimetric, Free Chlorine Range: 0.0 to 2.5
mg/L, Free Chlorine Resolution: 0.5 mg/L, Free
Chlorine Number of Tests: 50, Chlorine Method: DPD,
Weight : 176 g (6.6 oz.), Dimensions 220 x 145 x 55 mm
(8.7 x 5.7 x 2.1"), Ordering Information: HI3831F test
kit comes with color comparison cube, 20 mL reagent 1,
and 15 mL reagent 2.
1 2000
Principal
Govt. Polytechnic, Khamgaon
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions
issued.
3) Head of Electronics Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
1
Corrigendum 1: For Enquiry No. : No. : GPK /Store/inst purchase/MED/2019-20/21Date: 02/01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of Machinery and Equipment
during 2019-20 . Kindly note the updates shown in column no 5 below and do needful. The estimated cost
shown in column 5 is inclusive of all taxes , GST, transportation , handling, etc. (inclusive of all).
Sr.
No.
Name of the
item
specification Quantity
required
Estimated Cost
per item in Rs.
1
Real Time
Temperature
Controller
Temperature
Controller Test
Rig
This module consists of all necessary components
to establish a closed loop speed control of
temperature process. PLC acts as ON/OFF or PID
controller.
The details of this module are as follows:
• One water bath with heater provided.
• One AD-590 temperature sensor with the signal
conditioner provided.
Output: 0-10Volt.
• One Thyristor converter amplifier to provide 0-
220 Volt pulsating AC to the heater coil so that
linear control can be established.
• Input: 0-10Volt,
• Output: 0-220Volt
• One 31/2 digit DPM to display the temperature
of water bath.
• Application:
- To study the temperature control using PLC.
- To study the closed loop control using PID mode
by varying the proportional, integral, derivative
gain in PLC.
1 18750
2
Cylinder Cam
With
Reciprocating
Follower
Working Educational model of Cylindrical cam
with reciprocating Follower.
- All components made up of metal mounted on
wooden base.
- Manual input.
1 1700
3
Tangent Cam
With Roller
Oscillating
Follower
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual input.
1 2300
4
Disc Cam -
With Knife Edge
Follower ;
Roller Follower ;
Flat Face
Follower
Spherical
Surface
Follower
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual input. 1 1700
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
5
Wedge Cam
With
Reciprocating
Follower
Working Educational model.- All components
made up of metal which are mounted on wooden
base having different colors with naming on each
part for easier understanding.- Manual input.
1 2300
6
Conical Friction
Clutch
Working Educational cut section model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 4500
7
Simple Watt
Governor
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 2500
8
Porter Governor Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 4500
9
Hartnell
Governor
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 4500
10
Pickering
Governor
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 7800
11
Reversing Gear
(Reverted Gear
Train)
Working Educational model.
- All components made up of metal which are
mounted on wooden base having different colors
with naming on each part for easier understanding.
- Manual or Motorized input.
1 5000
12
Geometrical
Models Kit
Material Model set for Prism, Pyramid, cylinder
cone, Tetrahedron, cube.
- All components made up of acrylic.
- Liquid filled Acrylic material model set to show
section plane at different angles of solids and
frustum of solids.
1 2500
13
Model of
Dissected solids
Material model set of Dissected solids of Prism,
pyramids, cylinder, cone, Tetrahedron, cube.
- All components made up of acrylic.
-Acrylic material model set of intersection of
solids of Cone with cone, Cone with Pyramid,
Cone with Prism, Cylinder with Pyramid.
1 2800
14
Abrasive Jet
Machine Trainer
kit
1) Abrasive material – Al2O3/SiC/Glass Beads
2) Abrasive shapes- Irregular spherical
3) Abrasive size – 10-50
4) Mass flow rate- 2~20gm/min
5) Carrier gas composition- Air, CO2, N2
6) Air Jet Velocity- 500-700m/s
7) Pressure – 2-10 bars
1 40000
3
8) Flow Rate – 5-30 lpm
9) Mixing ratio –massfloww ratio of abrasive
to gas-Mabr/Mgas
10) Stand –off Distance- 0.5-5mm
11) Impingement angle- 600-900
12) Nozzle-Material – WC/ sapphire
13) Diameter- 0.2-0.8mm
14) Life- 10-300 hrs.
15 Electrochemical
machine setup
Mechnining Cell Technical Data : Tool Area – 30
mm2
, Cross head stroke – 150 mm. Job holder –
100 mm opening x 50 mm depth x 100 mm width.
Tool feed motor – DC servo type.
Control Panel Technical Data : Electrical out put
rating 0-300 Amps. DC at any voltage from 0-20
V. Effiiency – Better than 80% at partial & full
load condition. Power factor _ Better than 85.
Protections _ over load, short circuit, single
phasing. Operation Modes-
Manual/Automatic.Timer – 0-99.9 min. Tool Feed
0.2 to 2 mm/min. Z Axis control – forward,
reverse, auto forward/ reverse, through micro
controller. Supply -415 v +/- 10%, 3 phase AC,
50 Hz
1 40000
16 Pneumatic Robo
arm
AX-12A/AX-18A Smar Robotic Arm
Specifications (Standard Arm)
1, Overall length (form base)- 22.25” (56.15 cm)
2.Weight-2.21 pounds/1kg (Standard smart arm-
no upgraded)
3.Basse height- 1” (2.54 cm)
4.The base rotation servo is centered in a 4” x 4”
square(10.16cm x 10.16cm)
5.Repeatability 2.5 mm
6.Each axis has a 3000 range with 1024 steps (0-
29/step)
7.Initial base angle can be set in 450
increments.
8.Precision carbon steel ball bearing turntable.
9.Integratedpem nuts for quick and easy
construction.
10.Super strong anodized 0.063 ga. 5052 burshd
finished aluminum components.
11.Serch resistant type II anodized in gun barrel
gray.
12.(7) Dynamixel AX-12/AX-18 servos (5 axis +
1 gripper with standard smar Robotic Arm
configuration, 6-axis with 5-axis upgrade package.
Dimensional Information
Overall length – 22.26 in/56.54 cm
Overall weight –Standard arm with fixed initial
angle bracket- 2.0 pounds/1.18 kg
Note # 1- Smart Robotic Arm shown with optional
6 axis upgrade.
Note#2- With the standard fixed initial angle
bracket the base to first fixed angle would b3e
1 25000
4
Principal,
Govt. Polytechnic, Khamgaon.
Copy to :
1. Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued
2. Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions issued
3. Head of Electronics Department for information and n a
4. Suppliers as list attached herewith through email and by post
5. Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for uploading on
Institute website.
3.375 in/8.57 cm.
Grippers- Duel Gripper- The AX-12A or AX-18A
dual gripper kit provides a large 9 inch (22.86 cm)
gripper
% and 6 Axis Upgrades _ 5 – Axis Upgrade
Hardware, 5 Axis upgrade dehw kit
Controllers: CM-700 Contrller
5
[Type text] Page 1
Corrigendum 1: For Enquiry No. : GPK /Store/inst purchase/SCI /2019-20/ 25 Date: 02 /01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of
Machinery and Equipment during 2019-20 . Kindly note the updates shown in column no 5 below and
do needful. The estimated cost shown in column 5 is inclusive of all taxes , GST, transportation ,
handling, etc. (inclusive of all).
Sr.
No.
Name of the item specification Quantity
required
Estimated
Cost per
item in Rs.
1 Spherometer Range:-10 to +10 mm, LC = 0.01mm 4 450
2 Resistance Box 4 decade ranges from 1 ohm to 5000 ohm,
accuracy 0.1 % - 1% 3
2100
3 Boyle’s apparatus: U tube manometer, mercury Barometer 1
7400
4 Archimidies Principle
Set up
spring-balance, overflow-can , Liquid container
(Volume : 1000 ml) 1
3200
5 He-Ne laser Kit
(IFHN05)
Class II (0.4 to 1.0 mW) 1
22000
6
6
Photo resister/LDR
cell setup
photo resistor and variable light source
enclosed in a wooden box 1
4800
7 Ultrasonic Distance
meter
Range: 0 to 20 m 1
4800
8 Tuning Fork 5 Tuning fork of different range of frequency 2 1700
9 Experimental setup of
emf of two cells
Range 0 to 2 Volt 1 4800
10 Voltmeter Range 0 V to 5 V 5 560
Principal
Govt. Polytechnic, Khamgaon
Copy to : 1) Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued.
2) Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions issued.
3) Head of Electronics Department for information and n a
4) Suppliers as list attached herewith through email and by post
5) Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for
uploading on Institute website.
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
[Type text] Page 2
1
Corrigendum 1: For Enquiry No. : GPK /Store/inst purchase/ETX/2019-20/19 Date: 02/01/2020
Dear Sir ,
Please refer above cited enquiry letter of this Institute towards the supply of Machinery
and Equipment during 2019-20 . Kindly note the updates shown in column no 5 below and
do needful. The estimated cost shown in column 5 is inclusive of all taxes , GST, transportation ,
handling, etc. (inclusive of all).
Sr.
No.
Name of the item with specification Quantity
required
Estimated
Cost per item
in Rs. Name of the item Specification
1 2 3 4 5
1.
Analog Lab with
high quality bread
board on board DC
fix, variable and ac
power supply
On board DC fix, variable and ac power
supply, function and modulation generator,
continuity tester, high quality bread board,
toggle switches potentiometers &Optional:
ready to use on board
01 15000
2.
Trainer kit for
Sampling theorem
and PCM
modulation and
demodulation
STUDY OF SAMPLING THEOREM. Trainer kit
suitable to demonstrate the principle of
Sampling theorem which is basic of digital
communication system by IC based circuit. Kit
should have built in Clock generator, Pulse
generator Sample & Hold circuit, Microphone
Preamplifier & Filter circuit. Also provided
with signal recovery section. Effect of aliasing
should be demonstrated. Inbuilt DC supply and
various Test points.ii) PULSE CODE
MODULATION.Trainer kit suitable to
demonstrates the principle of pulse code
modulation. Kit should consist of Crystal based
clock generator, Divider circuit, A to D
converter and parallel to serial converter.
Trainer should give the pulse code modulated
signal at output. Inbuilt DC supply and various
Test points.iii) PULSE CODE
DEMODULATION Trainer kit suitable to
demonstrate the principle of pulse code
demodulation using IC based circuit. Kit
consists of serial to parallel converter, D to A
converter, filter and amplifier. This unit should
be matched with PCM trainer & original
modulating
02 5000
GOVERNMENT POLYTECHNIC, KHAMGAON WINNER OF ISTE-NARSEE-MONJEE AWARD-2000
(07263) 56644 (O), 54609 (R), Fax - (07263) 52278
E-mail: [email protected] Gram:- POLYTECH
2
Sr.
No.
Name of the item with specification Quantity
required
Estimated
Cost per item
in Rs. Name of the item Specification
1 2 3 4 5
3 Trainer kit for DPCM
modulation and
demodulation
Onboard DPCM Transmitter and receiver.
Onboard Audio input & output processing
.circuits Clock and entire control Signal section.
Detailed signal processing circuit with complete
data and control signal flow
Signal generator block. Functions: Sine and
Square ,O/P frequency range: 300Hz to 3.4
KHz,Audio blocks: Audio I/P and O/P processing
circuits Control signals: R/W for ADC, reset.
Latch enables, OEs.Sampling frequency : 8
KHz.Total Bits per sample :5 bits including sign
bit.Compared to 8 bit PCM :3 bits per sample
02 7500
4
Trainer kit for delta
and adaptive delta
modulation
Input Channel: Time Division Multiplexed
.Serial Crystal Frequency: 6.400
MHz.Sampling Clock Frequency: 50, 100, 200
& 400 KHz (Switch selectable).On board
Generator: Synchronized and
AdjustableIntegrator: Four integrator gain
settings .Normal, X 2, X 4, X 8Low Pass Filter
: Fourth order Butterworth (Cut Off
Frequency 4.8 KHz).
02 7500
5
Line code trainer for
UPNRZ, PRZ
,BPRZ , PNRZ ,
UNRZ.Manchestor
and Differential
Trainer kit for Study of Data
Formats.Technical Specification .Data
Formatting and Carrier Modulation Transmitter
.Crystal Frequency : 4.096 MHz.Data formats :
NRZ (L), NRZ (M), RZ, AMI, RB.Biphase
(Manchester), Biphase (Mark).On-board carrier
: Sine waves synchronized to transmitted data
at 1.6 MHz, 960KHz, (0 deg. phase) 960 KHz,
(90 deg. phase) Power Supply : 220/110V,
50/60 Hz.
02 5000
6
Trainer kit for ASK ,
PSK , FSK
modulation and
Demodulation
Trainer kit for Study of keying techniques .For
Study of Amplitude Shift Keying Study of
Frequency Shift Keying for Study of Phase
Shift Keying for Study of Differential Phase
Shift Keying for Study of Quadrature Phase
Shift Keying. Study of Differential Quadrature
Phase Shift Keying. Technical Specifications
Carrier Demodulation and Data Reformatting
Receiver Carrier Demodulation : ASK -
Rectifier
02 7500
7
Trainer kit for QPSK
modulation and
Demodulation
Trainer kit shall demonstrate principle of
QPSK modulation and demodulation 02 4000
8
Trainer kit for QAM
modulation and
Demodulation
Trainer kit shall demonstrate principle of QAM
modulation and demodulation 02 5000
9
CDMA – DSSS
signal generator and
demodulator
Trainer kit shall demonstrate principle of
CDMA DSSS signal generation and
demodulation
02 10000
3
Sr.
No.
Name of the item with specification Quantity
required
Estimated
Cost per item
in Rs. Name of the item Specification
1 2 3 4 5
10
FHSS signal
modulator and
demodulator
On-board data generators and PRN sequence
generators.BCD rotary switches for Data
Selection
Tap selectable PN sequence generators
Multiple data rate and chip rate selection
Variable processing gain selection
Slow and Fast frequency hopping
demonstration
PN sequence driven Frequency synthesizer
with non-overlapping frequency channel
assignment
Data Rates :16 Kbps, 8 Kbps and 4 Kbps
Word Length :8 bits
Data Format :NRZ (Not Return to Zero)
Chip Rates :240 KHz, 120 KHz, 60 KHz,
(DSSS CDMA)16 KHz, 8 KHz and 4 KHz (for
FHSS)
Sequence Type :Maximum Length Sequence
Sequence Pattern :Selectable through feedback
taps in LFSR array. BFSK Frequencies: 100
KHz for mark and 50 KHz for space .
Frequency Synthesizer
Output: Sinusoidal
Frequency Synthesizer: 1.6 MHz, 1.2 MHz,
800 KHz and 400 KHz . Channels Hoping
Channels :Four
Number of Hopes :Variable depending upon
data rate and chip rate per Data Periods
02 10000
11 Trainer kit for
MOSFET
Trainer kir suitable to plot I/p, O/P
characteristic of MOSFET with inbuilt DC
supply and required digital meters (4 No.) and
various Test point
02 4000
12 Trainer kit for single
tuned amplifier
Trainer kit suitable to plot the frequency
response of an Transistorized L-C tuned
(single) circuit amplifier. Centre frequency
above 400 Khz.( any other suitable frequency)
Inbuilt DC supply and various Test points.
02 4000
13
Trainer Kit For
Crystal Oscillator
Using Transistor
Trainer kit suitable to produce oscillations of
frequency 10 KHz ( any other suitable
frequency) Inbuilt DC supply and various Test
points.
04 5000
14
Trainer Kit For
Temperature On Off
Controller Kit
TEMPERATURE TRANSDUCER WITH
INSTRUMENTATION and ON/OFF
CONTROLLER USING R.T.D. Trainer kit
suitable to demonstrate the principle of
ON/OFF type controller using heating process.
Trainer should consist of RTD (standard PT-
01 4500
4
100) type transducer with instrumentation,
ON/OFF controller (Relay based) with facility
to set required temperature, Bulb heater having
facility to vary heater power, 3 ½ digit digital
indicator, Set temperature control, In built DC
Power supply etc. Unit operates on 230V, 50
Hz AC supply.
15
Trainer kit for BJT
series voltage
regulator
Trainer kit suitable to study the principle of
transistorized series voltage regulator used in
regulated power supplies. Measure the line &
load regulation. Inbuilt unregulated DC input &
various test points.
01 4000
16. Trainer kit for single
stage and Multistage
BJT amplifier
Trainer kit suitable to plot Frequency response
of 2 stage common emitter transistor amplifier
circuit. Facility to measure A1& A1xA2.
Inbuilt DC supply and various Test points.
02 3000
17. Trainer Kit for FM
Modulator using IC
566
AC Source:600Hz-2.5KHz, FM Modulator:
VCO, Test Points, Circuit diagram engraved on
front panel with transparent rear panel
03 4000
18. Trainer Kit for FM
Demodulator using
IC 564/565
AC Source:600Hz-2.5KHz, FM Demodulator:
VCO, Test Points, Circuit diagram engraved on
front panel with transparent rear panel
03 4000
19
AM Receiver
Trainer Kit
DSB/SSB AM Receiver Trainer: The trainer
should have following features- Variable
capacitor tuning, onboard local oscillator, RF
Amplifier, Mixer, IF Amplifier, Detectors,
Audio Output Receiving Antenna, AGC and
speaker, On Board Block diagram, Frequency
Range:980KHz-2060KHz and IF:455KHz
02 5000
20. PAM Trainer Kit
PAM Trainer Kit suitable to demonstrate the
principle of PAM using op-amp IC based
circuit with facility to vary depth of
modulation, inbuilt power supply and various
test points.
02 4000
21.
PWM Trainer Kit
PWM Trainer Kit suitable to demonstrate the
principle of PWM using TIMER IC based
circuit with facility to vary depth of
modulation, inbuilt power supply and various
test points, effect of change in carrier and
modulating signal should be studied, facility to
measure pulse width under steady input should
be provided.
02 4000
22 PPM Trainer Kit
PPM Trainer Kit suitable to demonstrate the
principle of PPM using IC based circuit with
facility to vary depth of modulation, inbuilt
power supply and various test points.
02 4000
23. Arduino Universal
Development Board
The Arduino Uno R3/R4 Kit with Arduino Uno
R3/R4 board and other important accessories.
With following facility on Advanced Arduino
UNO R3/R4 Board
Button to control LED.
Control LEDs by digital output pins
Relay
Control DC motor direction
10 3000
5
Stepper motor interfacing provision
16x2 LCD display interfacing
DAC0808 interfacing
Simple RGB LED on an ARDUINO UNO.
24.
8051 universal
development
platform
Core 8051 MCU clocked at 11.0592 MHz User
can enter opcode using on board 20 Hex
keypad,
For large program user can use on board PC,
based USB Programmer. On board LCD for
both programming mode and run mode
Every pin is marked in order to make work
easier, Interconnection for modules : 20pin
FRC cables, usb cables ,Software CD,
Connecting Patch Cords, Product Tutorial,
Setup >Experiment Trainer Board that
Contains:-Includes :-1.Power Supply : 5 V DC
2.signal generator:100Hz,
3.various test points,
connecting patch cord,
product tutorial
02 15000
25.
Input Interface
Module For 8051
UDP
experiments:-
1-4X4 Matrix keypad Interface,
2-ASCII keypad interface,
3-Four input sensing switch interface,
>Experiment Trainer board that Contains:-
1. PC based programming.,
2.Expansion connectors for plug in with
Microcontroller unit and prototyping area
3.Various test point
>20 pin FRC cable
>Connecting Patch Cords
02 5000
26.
ADC/DAC Module
For 8051 Udp
Experiments:-
1-To study interfacing 8 input 8 channel ADC
Interface,
2-To study interfacing DAC Interface
3-To study timing and control signals of ADC
and DAC pin to pin study of MCU
>Experiment Trainer board that Contains:-
1.PC based programming 2.Expansion
connectors for plug in with Microcontroller
unit and prototyping area
3.Various test point
>20 pin FRC cable >Connecting Patch Cords
>Product Tutorial
02 5000
27.
Computer Interface
Module For 8051
UDP
Experiments:-
1-To study basics of serial communication and
MCU connections to serial port
2-To study MCU connections to parallel port
3-To study of synchronous and asynchronous
serial communication.
>Experiment Trainer board that Contains:-
1.RS 232 interface using Rx/Tx of MCU for
Uploading / Downloading
02 5000
6
2.USB interface
3.PC based Programming
4.Expansion connectors for plug in with
microcontroller unit and prototyping area
5.Various test point
>20 pin FRC cable
>RS-232 Serial cable
>USB cable
>20 pin FRC cable
>Connecting Patch Cords >Product Tutorial
28.
Display Interface
Module For 8051
UDP
Experiments:-
1-To study implementation analysis
2-To study and analyze the interfacing of 16x2
LCD. 3-To study implementation analysis and
interfacing of seven segment display
>Experiment Trainer board that Contains:
1.Display : 16x2 LCD
2.Seven segment display : Four 3.Led bar
graph : one
4.Various test point
>20 pin FRC cable
>Product Tutorial
Experiments:-
1-To study implementation analysis and
interfacing of Stepper motor
2-To study direction and angle controlling of
stepper motor
3-To Study DC motor interfacing, PWM Servo
motor Servo motor
>Experiment Trainer board that Contains:-
1.Stepper motor : +12 V
2.DC motor : +12 V
3.Servo motor : +5 V
4.Various test point
>20 pin FRC cable
>Product Tutorial
02 5000
29.
Real Time Clock
Module For 8051
UDP
Experiments:-
1-16x2 characters LCD Interface
2-DS1307-RTC interface.
3-Latch switch interface
4-Buzzer and LED Interface
>Experiment Trainer board that Contains:-
1.Display :16x2 LCD
2.RTC : DS1307
3.RTC Interface type : I2C 4.Buzzer : +5 V dc
5.LED : +5 V DC , Battery : 3Vdc CMOS
5.LED : +5 V DC , Battery : 3Vdc CMOS
4.Various test point
>20 pin FRC cable
>Product Tutorial
02 5000
Principal
Govt. Polytechnic, Khamgaon
7
Copy to :
1. Hon. Director ,Directorate of Technical Education M. S. Mumbai for information please. It is
requested to do needful for uploading the same on website as per instructions issued
2. Hon. Joint Directorate of Technical Education Amravati Region, Amravati for information
please. It is requested to do needful for uploading the same on website as per instructions issued
3. Head of Electronics Department for information and n a
4. Suppliers as list attached herewith through email and by post
5. Shri Ambatakar , programmer through Registrar , Govt. Polytechnic , Khamgaon for uploading on
Institute website.
8