GEOPHYSICAL REPORTFOR
INTERNATIONAL LARDER MINERALS INC.ON THE
LOVELAND PROJECTLOVELAND TOWNSHIP
PORCUPINE MINING DIVISIONNORTHEASTERN, ONTARIO
Prepared by: J.C.Grant, GET, FGAC August, J.9,27 .
42A12NE0077 2.17730 LOVELAND 010
TABLE OF CONTENTS
Page
INTRODUCTION.......................................l
PROPERTY LOCATION AND ACCESS. . . . . . . . . . . . . . . . . . . . . . . l
CLAIM GROUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l
PERSONNEL..........................................2
GROUND PROGRAM.....................................2,3
SURVEY RESULTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONCLUSIONS AND RECOMMENDATIONS. . . . . . . . . . . . . . . . . . . . 4
CERTIFICATE
LIST OF FIGURES:
APPENDICIES:
PULL-OUTS:
POCKET MAPS:
FIGURE 1: LOCATION MAPFIGURE 2: PROPERTY LOCATION MAPFIGURE 3: CLAIM MAP
A: BRGM, IP-4 RECEIVERSCINTREX, IPC7, 2.5 KW TRANSMITTER
B: BRGM, OMNI IV MAGNETOMETER SYSTEM.
IP PSEUDO SECTIONS, LO,L200ME,L400ME
CONTOURED BASE MAP OF TOTAL FIELD MAGNETICS
42A12NE0077 2.17730 LOVELAND 010C
Page l
INTRODUCTION:
The services of Exsics Exploration Limited were retained by Mr. L. Bonhomme on behalf of International Larder Minerals Inc. to complete a linecutiing and ground geophysical program across a block of 4 claims located in Loveland Township of the Porcupine Mining Division, District of Cochrane in Northeastern, Ontario.
The purpose of this program was to test the claims potential for a conductive horizone which would be considered a favourable target for base metal deposition.
The program commenced on the 22 day of July and was completed on the 31 of July, 1997. A total of 4.4 kilometers of grid lines were cut and surveyed across the claim group.
PROPERTY LOCATION AND ACCESS;
The claim group is located in the southeast section of Loveland Township approximately 800 to 1000 meters northwest of the Kamiskotia River and the Robb/Loveland Township line. The entire block is located approximately 35 kilometers north-northwest of the City of Timmins. Refer to figures l and 2.
Access to the claims were ideal. The junction of Highways 101 west and 576 north is situated about 6 kilometers west of the City of Timmins. Highway 576 services the community of Kamiskotial Lake which is about 25 kilometers north of the afore mentioned junction. A good gravel road, locally called the Abitibi access road, travels north off of Highway 576, immediately past the lake, and crosses the claim group in a northwest to southeast direction. There are also a number of good secondary gravel roads cross cutting the grid in a number of locations, all of which run off of the Abitibi road.
CLAIM GROUP:
The claim number which makes up the 4 claim package covered by the ground program is P-1207544. Refer to figure 3 for the location of the claim within the Township. Figure 3 has been copied from the MNDM Plan Map of Robb Township.
HUDSON B A Y
ONTARIO
ft• OBULTON
QUEBEC
•CHBOUGAMAU
QHEARST
PROPERTY LOCATION
**
0QUEVLLON
|RCWN W •SEMMETBWE
'NOMANDA VALDOR
'OTTAWA
EXSICS EXPLORATION LTD.f A 9m MM. P4H-7X1
O. fomyr BU|. TkMin* Ont. 7-481
OJENT: INTERNATIONAL LARDER MINERALSpROPtRTY: LOVELAND TWP.TITLE:
LOCATION MAPFig.
Datt: July 1997
Drawn: P. Gauthier
Scati: ! "-l25m*les
Interp: J-C. GrantMNDM
Job No. E-272
\
LOVELAND TWP
ROBB TWF\
EXSICS EXPLORATION LTD.P.O. BM UN. P4N-7X1SwU O. Hrilhj* Md* TkMku Oof.~ ' ' 715-2*7-4151
CUENT: INTERNATIONAL LARDER MINERALSPROPERTY: LOVELAND TWP.TITLE:
CLAIM SKETCHDate: July I997
Drawn: P. Gauthier
Fig. 3
Scalt:|'W2mile
Interp: J.C. GrantMNDM P lan*: M-293
Job No. E-272
•"•"'l l,,,H,n } \ l^-"-'-
. A -~ -RiFFi'j
(PROPERTYCAtlON
\
u Xj i Harrie, L *
^ \ V-' JV-
J lUBO-V^-l. ""..i."———~——n" ,. ^ ~^T- 7- .vi' ' 'f -C'~t,- -ilV ' '- X. - ' f HL —f / IS a'- ' ' \^^ - V Hauwv~~~J ;^^**\s,tiwi,kii^s?,iSi,.r /re j ^**ui.3/T ff^L ipp^?
EXSICS EXPLORATION LTDBM m*, pin-mi
O. HaUhgv BUg. Tta^nt Ont : 705-2*7-4151
CLIENT: INTERNATIONAL LARDER MINERALSLOVELAND TWP.
PROPERTY LOCATION
Page 2
PERSONNEL:
The field crew responsible for the collection of the IP surveyresults are as follows:
Wayne Pearson......... . . ......Timmins, OntarioAlbert Ryan... . .... . . . . . . . . ...Timmins, OntarioCraig Pearson... . . . . . . . . . .....Timmins, OntarioMario Ruel... . . . . . . . . . . . . . . ...Timmins, Ontario
The magnetic survey was completed by J. C...Grant. The entireprogram was completed under the direct supervision of J.C.Grantwith all of the plotting and compilation being completed byP.Gauthier of Exsics.
GROUND PROGRAM:
The ground program was completed in two stages. The first stage was to cover the claims with a detailed grid which was cut using a 200 meter line spacing and 25 meters station spacing. A baseline was established across the top of the claims and all of the cut lines, 0+00 to 600ME were turned off of it. All 4 cross lines were cut 800 meters to the south boundary along which an 800MS tieline had been established.
The second phase of the program was to complete an IP survey and a total filed magnetic survey across the cut lines. The magnetic survey was completed over all of the cut lines whereas the IP survey was completed over lines O to 400ME. Line 600ME was not covered by the IP survey as the ground conditions were too dry and sandy to allow for a good electrode contact.
IP SURVEY:
The IP survey was completed using the BRGM, IP-4 receiver and the Scintrex, IPC-7 2.5 kilowatt transmitter. Specifications for this system can be found as Appendix A of this report.
Method. . . . . . . . . . . . . . ....Time domainArray...................Pole-dipoleElectrode spacing.. . . . . .25 metersNumber of electrodes . . . .n^-4Transmitter. . . . . . . . .....Scintrex, 2.5 kw transmitter and generatorPulse time........ . . . . . . 2 seconds on, 2 seconds offDelay time. . . . . . . . . . . . . .350 millisecondsIntergartion time. . . . . . . 700 millisecondsParameters measured.....Chargeability and apparent resistivityData presentation.......Single line pseudo sections of the
parameters measured; both contoured.A pseudo section of each of the grid lines read are included
as pullouts in this report.
Page 3
MAGNETIC SURVEY:
This survey was completed using the BRGM, OMNI IV system. Specifications for the unit can be found as Appendix B of this report.
The following parameters were kept constant throughout the survey. Line spacing..... . . . . . . . . . . . . . . . ...200 metersStation spacing.. . . . . . . . . . .. .. . . ... 25 metersReading intervals....... . . . . . . .... . 25 metersDiurnal Monitoring.................Base station loopingReference field............ .. . . . . . . 57,500 gammasDatum subtract.....................57,000 gammasParameters measured................Earth's magnetic fieldAccuracy...........................*/- 0.1 gamma
The collected data was levelled and then plotted onto a base map at a scale of 1:5000 and then contoured at 50 gamma intervals where possible. A copy of this contoured base map is included in the back pocket of this report.
SURVEY RESULTS:
The survey results did not appear to enhance the property's potential. The magnetic survey generally outlined what appears to be a north-northwest striking dike like feature which can be traced from the south end of line 400ME to the north end of line 0+00.
The IP survey did not return any encouraging results either. The survey seemed to react to the presense of the dike which may have a small amount of sulphide material associated with it's flanks. Generally these areas show up as single dipole high readings usually at depth with no continuity between lines. The entire grid was covered by sand and gravels which made electrode contact difficult and, in places, rsulted in noisy readings.
Page 4
CONCLUSIONS AND RECOMMENDATIONS:
The surveys were not successful in locating any definite conductive horizons on the four lines that were covered. The property appears to be cross cut by a dike like structure striking in a north-northwest direction. The width of the response may suggest that there are actually two parallel dikes.
The IP survey did not react to any conductive material except the possibility of minor sulphides along the edges of the dikes.
There was no areas of outcropping present on the grid as the entire area seems to be covered by a thick layer of sands and gravels. This type of overburden does not lend itself well to IP surveys.
No further work is recommended at this time.
Respectfully submitted
J.C.Grant, GET, FGAC August 4, 1997
CERTIFICATE
I, John C. Grant, hereby certify that:
1) I am a graduate technologist, (1975) of the three year program in Geological Technology at Cambrian College of Applied Arts and Technology, Sudbury Campus. I have worked subsequently as an Exploration Geophysicist for Teck Exploration Limited, (5 years), North Bay office and currently as Exploration Manager and Geophysicist for Exsics Exploration Limited since 1980.
2) I am a member in good standing of the Certified Engineering Technologist Association,(GET), since 1984
3) I am a Fellow of the Geological Association of Canada, (FGAC), since 1986.
4) I have been actively engaged in my profession since May of 1975, including all aspects of exploration studies, surveys and interpretation.
5) I have no specific or special interest in the described property. I have been retained as a Consulting Geophysicist by the Property holders.
John Charles Grant, GET, FGAC.
APPENDIX A
Major Benefits* 4 Dipoles Simultaneously Measured* Ten Windows Available
* Choice of Arithmetic or Logarithmic Window Width* Programmable Arithmetic Window Width* High Input Voltage
* Weighs Only 8.5 kg.
* User Friendly
SpecificationsDipoles . . . . . . . . . . . .! nput Voltage (Vp) Range
nput Voltage Protection . . /p Resolution . . . . . . . . . . . . . .Vp Accuracy Chargeability Resolution
Chargeability Accuracy .
\utomaticSPCompensation .
Input Impedance"ample Rate . . . . . . . . . .automatic Stacking
Synchronization . . . pejection Filters . . . . . . .
grounding Resistance Check . Compatible Transmitters
Programmable Parameters
uisplay .
emory Capacity . . . . RS-232C Serial I/O Interface . . .
jnsole Power Supply
Operating Environmental Range
' sight and Dimensions Standard System Complement
[ ;played Parameters
' a ilable Options
4 simultaneous input dipoles.Standard: 8 volt maximum for each dipole
maximum sum of 12 volts from thesecond to the sixth dipole. Additional Setting.-
attenuation of up to 40 volts on thefirst dipole.
.Up to 1000 volts. 1 microvolt.D.3% typical; maximum 1 07o over temperature range. 1 millivolt/volt for Vp greater than 10 millivolts. 0.1 millivolt/volt for Vp greater than 100 millivolts. Q.6% typical; maximum 207o for Vp greater than 10 millivolts over temperature range.
. 1 volt with linear drift correction up to 1 millivolt/second.
.10 megohm. . 10 milliseconds.
1 to 999 cycles.Minimum primary voltage level of 40 microvolts. . 50 and 60 Hz power line rejection greater than 100 dB.0.1 to 128 kilo-ohms.
. Any time domain waveform transmitter with a pulse duration of 1, 2,4 or 8 seconds and a crystal timing stability of 100 ppm.. Geometric parameters, time parameter, intensity of current, type of array, line and station number, dipole length, window width and delay time (mode 2). Two-line, 40-character alphanumeric liquid crystal display protected by an internal heater for low temperature conditions. 1800 sets of readings.
. 300 to 19,200 baud rate; 7 or 8 data bits; 1 or 2 stop bits; odd, even, no parity.Six - 1.5V "D" cell alkaline batteries with auto power save feature; 20 hours of operation at 20 0 C. . -400 C to + 600 C; O to 10007o relative humidity; weatherproof.8.5 kg. (with batteries), 300 x 200 x 240 mm.
. Instrument console with carrying strap, batteries, data transfer cable and operations manual. Primary voltage, partial and total decimalized chargeabilities, running and cumulative average of total chargeabiiities (in fixed modes), standard deviation of primary voltage and total chargeability, self potential, number of cycles, dipole being measured and contact resistance. Stainless steel transmitting electrodes, copper sulphate receiving electrodes, alligator clips, bridge leads, multi dipole wire cable, wire spools and software programs.
EDA Instruments Inr 4 Thorncliffe Park Drive Toronto, Ontario CanadaM4H IHI Telex 06 25222 PDA TOP Coble EDAINSTRMTS TOFOMTO Telephone (416)425 7800 Fax (416)4258135
'in USAEDA Instruments inc 9200 E. Mineral Avenue Suite 370Englewood, Colorado, USA 801 12 Teleohone '303) 790 2541 Fax (303) 790 2902
PPINTED Ifl CANADA
IPC-7/2.5KW Induced Polarization and Commutated DC Resistivity Transmitter
The l PC-7/2.5kW is a medium oower transmitter system used under a wide variety of geophysical, climatic and topograpnic conditions. It consists of an electronic console, a motor-generator and a dummy load whicn takes the power loaa during parts of the time domain cycle when current is not transmitted into the ground.
The compact design of this system maKes it portable and highly versatile for use with a wide variety of electrode arrays.
The PC-7/2.5kW features an overload protection circuit and an open IOOD circuit wnich protects ooth the mstrumen; and tne operators The built- in onmmeter permits verification that the current
dipole circuit is grounded which is not only a safety feature but also allows selection of adequate current for proper signal at tne receiver
Very high period time stability is ensured oy a crystal-controllec programmer making tne IPC-7, 2.5kWideal for t'oadband soectrai inaucea polarization measurements.
The transmitte" console has a maximbm current output of 10 A ^d a voltage output ranging from. 200 1210 V ' : . When couoied with tne 2.5KW motor-gener jr. the maximum output cower of this overall f item is l.85kW which results m a very favora 1 .e powerweight ratio
APPENDIX B
Four Magnetometers in One
Self Correcting for Diurnal Variations
Reduced instrumentation Requirements25 07o weight Reduction
User Friendly Keypad Operation
Universal Computer interface
Comprehensive Software Packages
specificationsRange
Tuning Method
itomatic Fine Tuning
Display Resolution ocessing Sensitivity atistical Error Resolution
Absolute Accuracy
andard Memory Capacity Total Field or Gradient Tie-Line Points Base Stationsplay
l 232 Serial i/O interfaceGradient ToleranceTast Mode .............
l-nsor
r adient Sensors
Sensor Cable . . . . . .. . . . ..... . . . . .
( cling Time (Base Station Mode)
Operating Environmental Range l wer Supply
[ ttery cartridge l Belt Life
Weights and Dimensionsnstrument Console only . . . \liCad or Alkaline Battery cartridge NiCad or Alkaline Battery Belt '.ead-Acid Battery cartridge .ead-Acid Battery Belt . . . .. . . .. .sensor .. ......... ........ . .. .Gradient Sensor
(0.5 m separation - standard) :radient Sensor(1.0 m separation-optional) .
Standard System complement
Base Station Option Gradiometer Option
18,000 to 110,000 gammas. Roll-over display featuresuppresses first significant digit upon exceeding 100,000gammas.Tuning value is calculated accurately utilizing a speciallydeveloped tuning algorithm 150/0 relative to ambient field strength of last storedvalue0.1 gamma 0.02 gamma0.01 gamma 1 gamma at 50,000 gammas at 23 0 C 2 gamma over total temperature range
1,200 data blocks or sets of readings 100 data blocks or sets of readings 5,000 data blocks or sets of readings Custom-designed, ruggedized liquid crystal display with an operating temperature range from -40 0 C to + 55 0 C. The display contains six numeric digits, decimal point, battery status monitor, signal decay rate and signal amplitude monitor and function descriptors. 2400 baud, 8 data bits, 2 stop bits, no parity 6,000 gammas per meter (field proven) A. Diagnostic testing (data and programmable memory) B. Self Test (hardware)Optimized miniature design. Magnetic cleanliness is consistent with the specified absolute accuracy. 0.5 meter sensor separation (standard), normalized to gammas/meter. Optional 1.0 meter sensor separation available. Horizontal sensors optional. Remains flexible in temperature range specified, includes strain-relief connectorProgrammable from 5 seconds up to 60 minutes in 1 second increments
. -400 C to H-55"C; Q-100% relative humidity; weatherproof
. Non-magnetic rechargeable sealed lead-acid battery cartridge or belt; rechargeable NiCad or Disposable battery cartridge or belt; or 12V DC power source option for base station operation.2,000 to 5,000 readings, for sealed lead acid power supply, depending upon ambient temperature and rate of readings
2.8 kg, 238 x 150 x 250mm . 1.2 kg, 235 x 105 x 90mm . 1.2 kg, 540 x 100 x 40mm . 1.8 kg, 235 x 105 x 90mm . 1.8kg, 540 x 100 x 40mm . 1.2 kg, 56mm diameter x 200mm
. 2.1 kg, 56mm diameter x 790mm
2.2 kg, 56mm diameter x 1300mm instrument console; sensor; 3-meter cable, aluminum sectional sensor staff, power supply, harness assembly, operations manual. Standard system plus 30 meter cable
. Standard system plus 0.5 meter sensor
EDA instruments inc. 4 Thorncliffe Park Drive Toronto, Ontario Canada M4H miTelex: 06 23222 EDA TOR Cable: instruments Toronto (416)4257800
In U.S.A.ED A instruments inc. 5151 ward Road wneat Ridge, ColoradoU.S.A. 80033 (303)4229112
Printed in Canada
m CHO-.
RESISTIVITY M7 CHG-.M7
4 1
p __
D '
RES M7r- 600
400
7755 7505 7255 7005 6755 650S 625S 6005 5755 550S 5255 SODS 475S 4505 4253 4DOS 375S 350S 3253 3DOS 275S 250S 2255 2QQS 175S 1505 125S 10DS
^ 75p QpS 650S 6005 55pS 50S 45pS 4 2pS 4 0pS 35S 325S 3QS 25pS 225S p gOpS , 1755 | 1 5pS , 1255 , IQpS
N:3
N:4
3 . 3 2.6 3-6 3. l 3.2 , l .2 L- 7 l .2 -.7 , -4 1 -6 2-6 2-9 3 -61.0 - 8 .5 1 .5 1 -6 L.
-S 1-2 1 -4 \2.23-5 3 .5 3 .3 3 -3 l
1.3 1.1 1-7 l -4 .3
1.6 1 -5 -9 - 9
/.9 1-9 1 .6 l -5 l .5 1 .3
l .1 . 6 2,0 L.I l .5 l .2
K l - 5 l .y 2^N 1 -6 L O 1 -2
Dike High
RESESTJVITY451 .8 329-B
O . 3
372-2 2 40-8 195-9417.6 37^.8 2 11 - 2^82=7 35.9 15
4.4 338-3 28iU 4 2^.2 2B-
.1 30.7 4.5 2St).
77.0 3102 353.0 39\.0\8^.61
221-7 196-9^53
M7 CHO. Nil
N:2
N:3
-. . --. . ^^.^^ . 130:S234. l V70.7x264.5 2W21645.4 *7S .7 293/5 232-9^73.4 447-3 453.0
-.4 134.8 l^ftTfr.135.9 151.4 130.7 1^ . 1\266. 8 ^5^,331^^222^1 560 .3 1359 .3 2B3-3 236.^579^4^97.^80.7 N:4
RESISTIVITY
N:2
N:3
LINE : O E
INDUCED POLRRIZRTION SURVEY
POLE-DIPOLE RRRflT
N - l , 2 , 3 , 4. .. . fi" SPRCING = 25-0 METRES
INTERNRTIONflL LRRDER MIN
LOVELflND TNP .
DRTE : JULY 1997 REF : E272
SCRLE ~ l : 24007 T
EXSICS EXPLORflTION LTD-'
M7 C HO-.
REStSTIVITY M7 CHO-M7
6 —i
4 —
2 —J
RES2000 —i
1000 —
RES M7 — 2000 — 6
h- 1 000
7755 7505 7255 700S 6755 6505 6255 6005 5755 5505 5255 5005 4755 4505 4255 4005 3755 3505 3255 300S 2755 2505 2255 2005 1755 1505
— 4
— 2
7 7 5S L 75pS 70pS 65pS 625S 60pS 575S 525S7
475S . 45pS 425S t 40pS ^ 375S 35pS 30pS ,g75S | 25pS 20pS
N:2
N:3
N:4 5-5
.0 3-4 3-0 3.-9^ 3-9 ^ 4.0 4-0 4.2 ^3-5 3-0 3-1 3-2 3-8 3-5 3-7 3.4
3-8 3.5 4-TJ) 3-6
.9 14-7 "5.0 3^- T.3 3-3\ 5.31 l J 2 -4 2-4 "3-0 2-8 2-8 3.4 2.6 3.4
8 /7T4N 12-4 2-5 ^^Ts^IR\\ l ^?~^ 2.0 L,9 2.4 ^-rg -^fi .0 N:4
RESISTIVITY
x Dike7755 , 75pS\7255 , 70p5 55p5 ,5255 , 5Qp5 ,4755 .45p5 ,4255 ,40p5 . 3755 , 35p5 ,325S , 3Qp5 ,2755 ,25p5 ,22^5 ;20p5 ,1755 , 15p5
N:l 464.9 458-3
N:2 318-9 323
N:3 2G2.
N:4 209
1.4K 1.6K969.
1-3K
1.6K l .2K 1.3
l -5K90
1.2K I.IK
REsisTivnrN:l
Nt2
N:3
N:4
LINE 200 E
INDUCED POLflRIZRTION SURVEY
POLE-DIPOLE RRRRY
N z l, 2. 3, 4, ...'fi' SPflCINC = 25-0 METRES
INTERNRTIONflL LflRDER MI
LOVELRND TWP.
DRTE : JULY 1997 REF : E272
SCflLE - l : 2400
EXSICS EXPLORnTION LTD
\\1 C HG.
: RESISTIVITY H7 C HO.M7
A —
O —*
RES 2000 —i
1000 —
O H——i——t- H———i———l
RES M7 r— 2DDO
l— 1000
9005 7755 750S 725S 7005 6755 6505 625S 60QS 5755 55QS 5255 50QS 4755 4505 4255 4005 3755 3505 3255 300S 275S 250S 225S 2005 1755 1505 125S 1005
8Qp5 7755 7 5QS 72SS 70QS L 6755 65pS | 625S 45p5 425S i 40pS | 375S | 35pS . 32pS ] 30pS 25pS | 225S | 20pS 5pS IQpS
N:l
N:2
N:3
N:4
2.9 3-7 4.1 . 4.0 3 -8 4,-3 3-5 3.7 3 -8 2-7 3-0, 4,1 3-6
.1 4.9 4 .2 4 .2 4 .7
2.3 2 .4 .9 -4 1.5, 2.1 1-5 .7 3-5 3-1 3-1 3 -2 3
1.2 -3 1.1 L4V2-2 2-8 3-2 3 -0 4 -0 3-G X" "^*-5 2-9
1.4 LO -3 1.0 -9 -4"~7F TTT ^9^ 2 -3 2-1 3 -3
.3 -5 .7 .4 .7 1.2 .9 1.1 .9 19 3.0 l 1-6
RESISTIVITYSOpS , 7755 ,75p3 ,725S , 70p5
Dike,65pS , 6253 ^OpS ,575S i 5 5p5 ,525s 475S 45pS 4Dp5 ,3755 , 35p5 , 3255 , 3QpS ,275s , 25pS , 225S , 2QpS , 1755 , 15p5 , 1255 , IQpS
N:l 857-3 673-2 743
Ni2 578.548
N.i3 311-2
H M 523 445x3^2561^-411.7 60
5 472-4 4 21-1 205-8 241 -3 305-9 4 50.1 379-0 2.36-5 391.1 l . BK734, l 6 57-
6?53ft42-7 316- W^S-O Q&Q.4 3 40.4 380-3 223 - 7/fttff\ 8(6^ .O^C5--3^oT5 -,
l 3^4.6 417.6 51JUS
s. o.3 294.4 2foX383-6 22^1
;5.5\434.0 027.5 BO l .7 670,1 46V.7 321 .9 538.9 264.6 247 .5 230.7 293.4 165.3\54aJ-3 343.8
M7 CHG. Mtl
Ni3
Nt4
RESISTIVITY Nil
N:3
N:4
LINE 400 E
INDUCED POLRRIZRTION SURVEY
POLE-DIPOLE RRRRY
N z l. Z. 3. 4. .. . F H" SPfiCING = 2 5.0 METRES
INTERNflTIONRL LflRDER MI
LOVELRND TUP .
DflTE : JULY 1997 REF : E272
SCflLE - l
EXSICS EXPLORRTION LTD.
OntarioMinistry ofNorthern Developmentand Mines
Declaration of Assessment Work Performed on Mining LandMining Act, Subsection 65(2) and 66(3), R.S.O. 1990
Transaction Number (office use)
Isessment Files Research Imaging
Personal information cc Mining Act, the informal Questions about this i 933 Ramsey Lake Roac
66(3) of the Mining Act. Under section 8 of the xk and correspond with the mining land holder. Jorthern Development and Mines, 6th Floor,
42A12NE0077 2. 17730 LOVELAND yUU
Instructions: - Fc , .... ..... - -.. -.-.... ..-~ ~-,~,~ . .-...3 K v.o.m, use form 0240. - Please type or print in ink. A -| W r^ O A
1. Recorded holder(s) (Attach a list if necessary)Name t ^
/i /i x7 l i ! X y ^^*-~-~ .~ //'//s L- 7 l f~,L,j ,""r ^ s ; /2 , S f" v /t- //v. "^"Y f 'c'^T^l t^-fti—tf— [ ' s* j / ^-^XVJ
Address
^V7r7 ̂ 7 , ^ r /^- , - /^'. 7 y^^Name
Address f^.
*ODCT n* - -
Client Number ,y ^y /^ p f "' if ™ ^x ^J *~'f ^ _ .
Telephone Number
T x -7 S c- / / C/,^/ 6s y -^ a. / (*-~ YFax N umber
Client Number
Telephone Number
Fan. N umber
W2. Type of work performed: Check ( ^ ) and report on only ONE of the following groups for this declaration.
Geotechnical: prospecting, surveys, assays and work under section 18 (regs)
Physical: drilling, stripping, trenching and associated assays
Rehabilitation
Work Type Office Use
Commodity
Total S Value of Work Claimed
Dates Work Performed From
Day
?~ ToDay Month
NTS Reference
Global Positioning System Data (if available) Township/AreaMining Division
M or G-Plan Number Resident Geologis District
Please remember to: - obtain a work permit from the Ministry of Natural Resources as required;- provide proper notice to surface rights holders before starting work;- complete and attach a Statement of Costs, form 0212;- provide a map showing contiguous mining lands that are linked for assigning work;- include two copies of your technical report.
3. Person or companies who prepared the technical report (Attach a list if necessary)Name
L f 7 /'^bt'^J L~Telephone Number
/Address Fax Number
Name Telephone Number
Address Fax Number
Name 4UG 7 1997 Telephone Number
Address
PORCUPINE MINING DIVISION
Fax Number
4. Certification by Recorded Holder or Agent
^ ^ . - , T , , do hereby certify that l have personal knowledge of the facts set
forth in this Declaration of Assessment Work having caused the work to be performed or witnessed the same during or after its completion and, to the best of my knowledge, the annexed report is true.
signature of Recorded Holder or Ageru
Agent's Address
f?Telephone Number Fax Number
5. Work tc be recorded and distributed. Work can only be assigned to claims that are contiguous (adjoining) to the mining land where work was performed, at the time work was performed. A map showing the contiguous link must accompany this form.
Miningwork ws mining column indicate
eg
eg
eg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Claim Number. Or if s done on other eligible and, show in this the location number d on the claim map.
TB 7827
1234567
1234568
/.} c ~~?^y^
Number ol Claim Units. For other mining land, list hectares.
16 ha
12
2
X/ J
Column Totals x
Value of work performed on this claim or other mining land.
S26, 825
0
S 8, 892
5 ^ il - \l
^A/
^07 ̂
Value of work applied to this claim.
N/A
S24,000
S 4,000
*\^QO - C r
4'
V
^rCv
" ^ K
^ ,f
^Mto-co
l IS t f / / 'C''' A
Value of work assigned to other mining claims.
S24,000
0
0
i ^i*
^
X( s ' ^) n 7
Bank. Value of work to be distributed at a future date.
S2,825
0
S4.892
1 O3"\ o c
s
* \ 0 ?, 1- - C c
, do hereby certify that the above work credits are eligible under(Print Full Nanrfe)
subsection 7 (1) of the Assessment Work Regulation 6/96 for assignment to contiguous claims or for application to
the claim where the work was done.
Signature of Recorded Holder or Agent Authorized in Writing Date
6. Instructions for cutting back credits that are not approved.
Some of the credits claimed in this declaration may be cut back. Please check ( ^ ) in the boxes below to show how
you wish to prioritize the deletion of credits:
K\ 1 . Credits are to be cut back from the Bank first, followed by option 2 or 3 or 4 as indicated.
Q 2. Credits are to be cut back starting with the claims listed last, working backwards; or
H 3. Credits are to be cut back equally over all claims listed in this declaration; or
D 4. Credits are to be cut back as prioritized on the attached appendix or as follows (describe):
Note: If you have not indicated how your credits are to be deleted, credits will be cut back from the Bank first, followed by option number 2 if necessary.
For Office UseReceived Stamp Deemed Approved Date
Date Approved
Date Notification Sent
Total Value of Credit Approved
Approved for Recording by Mining Recorder (Signature)
OntarioMinistry ofNorthern Developmentand Mines
Statement of Costs for Assessment Credit
Transaction Number (office use)
Personal information collected on this form is obtained under the authority of subsection 6(1) of the Assessment Work Regulation 6/96. Under section 8 of the Mining Act, the information is a public record. This information will be used to review the assessment work and correspond with the mining land holder. Questions about this collection should be directed to the Chief Mining Recorder, Ministry of Northern Development and Mines, 6th Floor, 933 Ramsey Lake Road, Sudbury, Ontario, P3E 6B5.
Work TypeUnits of Work
Depending on the type of work, list the number of hours/days worked, metres of drilling, kilo metres of grid line, number of samples, etc.
Associated Costs (e.g. supplies, mobilization and demobilization).
Cost Per Unit of work
Total Cost
'-f-
Transportation Costs
Lod9'ng Costs
Total Value of Assessment Work
Calculations of Filing Discounts:
1. Work filed within two years of performance is claimed at 10007o of the above Total Value of Assessment Work.2. If work is filed after two years and up to five years after performance, it can only be claimed at 5007o of the Total
Value of Assessment Work. If this situation applies to your claims, use the calculation below:
TOTAL VALUE OF ASSESSMENT WORK x 0.50 = Total $ value of worked claimed.
Note:- Work older than 5 years is not eligible for credit.- A recorded holder may be required to verify expenditures claimed in this statement of costs within 45 days of a request for verification and/or correction/clarification. If verification and/or correction/clarification is not made, the Minister may reject all or part of the assessment work submitted.
Certification verifying costs:
-^rC' ' s 4^.\ nam
, do hereby certify, that the amounts shown are as accurate as may(please print full name)
reasonably be determined and the costs were incurred while conductingassessment work on the lands indicated on
the accompanying Declaration of Work form as
to make this certification.
recorded holder, agent, or stawcompany position with signing authority)am authorized
Date
/-/f// 4 f /'.
Ministry ofNorthern Developmentand Mines
Ministere du Developpement du Nord et des Mines Ontario
October 27, 1997
JOHN PETER HUOT36 MAPLE STREET, SOUTHTIMMINS, ONTARIOP4N-7H9
Geoscience Assessment Office
933 Ramsey Lake Road 6th Floor Sudbury, Ontario P3E 6B5
Telephone: (888)415-9846 Fax: (705) 670-5863
Dear Sir or Madam:
Subject: Transaction Number(s):
Submission Number: 2 .17730
StatusW9760.00389 Deemed Approval
We have reviewed your Assessment Work submission with the above noted Transaction Number(s). The
attached summary page(s) indicate the results of the review. WE RECOMMEND YOU READ THIS
SUMMARY FOR THE DETAILS PERTAINING TO YOUR ASSESSMENT WORK.
If the status for a transaction is a 45 Day Notice, the summary will outline the reasons for the notice, and any
steps you can take to remedy deficiencies. The 90-day deemed approval provision, subsection 6(7) of the
Assessment Work Regulation, will no longer be in effect for assessment work which has received a 45 Day
Notice.
Please note any revisions must be submitted in DUPLICATE to the Geoscience Assessment Office, by the
response date on the summary.
If you have any questions regarding this correspondence, please contact Steve Beneteau by e-mail at
[email protected],on.ea or by telephone at (705) 670-5855.
Yours sincerely,
ORIGINAL SIGNED BYBlair KiteSupervisor, Geoscience Assessment OfficeMining Lands Section
Correspondence ID: 11510
Copy for: Assessment Library
Work Report Assessment Results
Submission Number: 2 .17730
Date Correspondence Sent: October 27, 1997 AssessonSteve Beneteau
Transaction NumberW9760.00389
Section:14 Geophysical MAG 14 Geophysical IP
First Claim Number1207544
Township(s) l Area(s)LOVELAND
StatusDeemed Approval
Approval Date
October 27, 1997
Correspondence to:Resident Geologist South Porcupine, ON
Assessment Files Library Sudbury, ON
Recorded Holder(s) and/or Agent(s):John C. GrantTIMMINS, ONTARIO, CANADA
JOHN PETER HUOT
TIMMINS, ONTARIO
Page: 1Correspondence ID: 11510
Thorburn Twp. (M.601)
-989*54 l 968453 9B3437
T
-i- - - -i - - - - mmmwm^m- M I ) gg^QMi^- - -,— ,_ ' ._ _ _,~ -; -j —
5 : : MI TS
Ilvv9(v W UNfi 9 ( 5 UNITS) lg)
1188918j&^AaaK k
(to'UNITS24758 NITS
p i p j yi- - -- ———M
goooeb ssoeoat
| P HSM48 l 2 UNITS
ii 99 9 1! ^1218694 (12 UNITS)
- .- -,-,,.__,i, . wwifcw
^ -- J S*fr4#*~ l ' ~^
F J1034655 98813.7^ j
S94G5
-,t IP^P^^U*. .JI
J/ 1 J2I293I
1212932
13 UNITS
Robb Twp. (M.309)
THE TOWNSHIP OF
LOVELANDDISTRICT OF
COCHRANE
PORCUPINE MINING DIVISION
SCALE: 1-INCH 4O CHAINS
LEGEND
WTENTtO LAND CROWN LAND SALE LEASESLOCATED L AND LICENSE Of OCCUPATION
..MINING RIGHTS ONLY SURFACE RIGHTS ONLYROADSIMPROVED ROADSKING'S HIGHWAYSRAILWAYSPOWER LINESMARSH OR MUSKEGMINESCANCtLIK)
i*
c
NOTES
400' Surface Rights R a servo t ion o Ton qthe shores of all -lake* and rivers
This township lies within the Municipality of ""rv of
7HfS1993/96
O FORESTRY ACT;
""3 AVAILABLE ON FILE
OCM
ff
Z68UZ130
dO 31VO
THE I NFORMATION APPEARS ON THIS ,
HAS BEEN COMPII FROM VAR'OUS SOUfUNO ACCURACY isGUARANTEED. TH- WISHING TO STAKE ING CLAIMS SHOULD SULT WITH THE MINI RECORDER, MINIStflV NORTHERN DEVELi WENT AND MINES. FOR OITIONAL INFORMAT! ON THE STATUS OF LANDS SHOWN HER'J(
PLAN NO. M-293\KIO
MINISTRY OF NATURAL RESOURCESSURVEYS AND MAPPING BRANCH
BASELINE
\
42A12NE0077 2.17730 LOVELAND 210
so__ loo 150 ^oo
SCALE (m)
\\
\\
\\
LEGENDInstrument: BRGM DMNI-IVParameters Measured' Earth's total magnetic fieldAccuracy' +X- 0.1 nano-teslasDiurnalsi Corrected by tie line loopingContour Interval' 0,50,100,150,200,250,,,,.Reference Field; 57,500 gannasDatun Subtracted; 57,000 gamnas
EXSICS EXPLORATION LTDP.O. Box 1880, P4N-7X1Suite 13, Hollinger Bldg, Timmins Ont.Telephone: 705-267-4151
CLIENT: INTERNATIONAL LARDER MINERALSPROPERTY: LOVELAND TWP.TITLE:
MAGNETOMETER SURVEYDate: July 1997Drawn:P.Gauthier
Scale: 1:5000Interp: J.C.Grant
NTS:Job No.:E-272