Download - Especificaciones Geommembranas
www.geoembalses.com
HIGH PERFORMANCE IN PROTECTION AND IMPERMEABILITY BARRIER
The Geo-membranes are a part of the investigation and development of a Group of Companies leader in polyethylene film production. Quality and service are behind the success of our products. The quality comitment begins with the evaluation of technical requirements of a waterproofing system, and the responsibilities derivated. The election of raw materials, and the quality process are made under the supervision of a professional team that control the intrinsical properties of the product during the whole process of production and checks that the Geo -membrane conforms the normalized parameters. Reservoirs and water tanks, cisterns, coating of wells, supplying and irrigation ch annels, industrial and sanitary fillings, ornamental lakes, pools for golf courses, waterproofing and sealing of rubbish dumps, tanks for pools and fish farms, tunnels and roads, mineral patch es
and secondary contention, protection against erosion.
www.geoembalses.com
UNE ÉTANCHÉITÉ ET UNE PROTECTION DE PERFORMANCE Nous vous proposons une gamme de bâches et Geotextiles spécifiquements développées pour l’imperméabilisation de performance. GEO 1 est une bâche de polyéthylène de haute densité PEHD. Fabriqué dans des conditions et sous un stricte controle de qualité et sous les normes Européennes de fabrications (Norme EN) et Certifications (Asqual). Afin de garantir un produit qui apportera toute la résistence et garantir ainsi un produit de longue durée et une solution pour chaque nécessité:
TRAVAIL CIVIL; GÉNIE CIVIL ; RÉALISATION TECHNIQUE
- barrages et basins - reservoirs y citernes - recouvrements de puits - canaux d’irrigation et distribution - lacs artificiels - d’étangs pour des champs de golf - imperméabilisation et scellage de dépotoirs - bassins pour des piscines et établissements piscicales - zones de lixibation minière et contención sécundaire - tunnels et réseau routier - protection contre la corrosion
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 1,0 GE0-G
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-150 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 22, 1 - -
apparent cohesion kPa 2,8 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 1,0 GEO-SA
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-200 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa 8,6 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 1,0 GEO SAS
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-150 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa 8,6 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the produc t using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA1,5 GEO-G
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,8 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-150 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,5 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 22, 1 - -
apparent cohesion kPa 2,8 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recomme ndations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA1,5 GEO SA
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,8 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-200 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,5 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa 8,6 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recomme ndations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA1,5 GEO SAS
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 3,8 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 100-200 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 1,5 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa 8,6 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recomme ndations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2 GEO G
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 5,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 80-120 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 2,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 22, 1 - -
apparent cohesion kPa 2,8 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendati ons for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2 GEO SA
.
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 5,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 80-120 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 2,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa 8,6 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2 GEO SAS
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 5,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 80-120 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 2,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4 npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11 -0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree - -
apparent cohesion kPa 28, 1 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2.5 GEO G
.
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 6,3 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 50-100 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 2,5 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 22, 1 - -
apparent cohesion kPa 2,8 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recommendations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2.5 GEOSA
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINI MUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 6,3 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 50-100 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 2,5 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 28, 1 - -
apparent cohesion kPa - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this in formation could i nvol ve us and compr omise us for the product using made.- This information could be change
without notice fr om us. We decline the r esponsability in case of breakage, incident or clai m, when the manufacturer's recomme ndations for use have not been respec ted. According to
manufacturing Standards Norms a fl uctuation aprox. +-5 % is permitted.
APPLICATION PRODUIT / PRODUCT APPLICATION / ANWENDUNG DES PRODUKTES/APLICACIONES
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.
www.geoembalses.com
DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 3 GEOSA
TOLERANCE
PROPERTIES METHOD UNITS NOMINAL VALUE
MINIMUM MAXIMUM
Normative part
Max. tensile strength EN ISO 527, N/mm2 30 / 30 -2 / -2 - / -
MD/CMD specimen 5
Elongation at break EN ISO 527, % 800 / 800 -40 / -40 - / -
MD/CMD specimen 5
Puncture resistance EN ISO 12236 kN 6,5 -0,5 -
Gas permeability ASTM D 1434 m3/m
2.d 3,29E-3 - -
(Gas tightness)
Water permeability EN 14150 m3/m
2.d U=1, 75E-06 - -
(Permeability to liquids)
D=1,66E-06
Resistance
-Resistance to weathering EN 12224 - Strength and elongation reduction <25% of
original values. Life expectancy min. 25 years.
-Resistance to oxidation EN 14575 - Strength and elongation reduction <25% of
original values.
-Stress crack resistance ASTM D 5397 hour >200
Informative part
Roll length EN 1848-2 m 50-100 - -
Roll width EN 1848-2 m 5,1 and 8,0 -0,02 +0,02
Thickness EN 1849-2 mm 3,0 -0,1 +0,1
Straightness EN 1848-2 mm <10 - -
Dimensional stability EN 1107-2 % <2 - -
Coefficient of Linear Thermal ASTM D 696 mm/mm /°C 1,76E-4
npd npd
Elongation at yield EN ISO 527 N/mm2 17 / 18 -0,85 / -0,9 - / -
MD/CMD specimen 5
Elongation at yield EN ISO 527 % 12 / 11
-0,6 / -0,75 - / -
MD/CMD specimen 5
Shear test: EN ISO 12957-1
angle of friction degree 22, 1 - -
apparent cohesion kPa 2,8 - -
Valid from: 01.01.2009
These values are measured for informational purposes, In any case this information could i nvol ve us and compr omise us for the product using made.- This information could be change without
notice from us. We decline the responsability in case of breakage, i ncident or claim, when the manufacturer's recommendations for use have not been respected. According to manufacturing
Standards Norms a fl uctuation aprox. +-5 % is permitted. DATA SHEET / FICHA TECNICA / FICHE TECHNIQUE PEHD TA 2.5 GEOSA
EN 13361, EN 13362, EN 13491, EN 13492, EN 13493
Geosynthetic barriers
This product does not contain any dangerous substances.