Engelking Elektronik GmbH
Switches Catalogue No. 7
Engelking Elektronik GmbH
Switches Catalogue No. 7
First digit 6: Dust tight. No ingress of dust.
IP Degrees
Second digit5: Protected against jets of water from any direction.
7: Protected against the effects of temporary immersion in water (submerged for 30 minutes at 1m depth).
6: Protected against powerful jets of water. Prevents ingress sufficient to cause harm.
Extended IP (eIPxx) for harsh enviromentsC: Cleaning chemicals added to water, depth and duration to be specified.
8: Protected against the effects of continuous immersion in water (submerged for more than 30 min- utes at more than 1m depth, to be specified).
Switches that fullfill the requirements of IPX6 also fullfill the requirements for IPX1 to IPX5.
O: Duty cycle operated under water, depth to be specified.
Extended IP digits can be combined.
2
General Information
Definition of Terms
Circuit: The contact arrangement with the switch actuator and contacts in their free position.Maintained Switch: A switch with contacts that sustain in operated position when actuating force is removed.Momentary Switch: A switch with contacts that return from operated to free position when actuation force is removedFast Connect Terminals: A plug-in type terminal designed for quick switch wiring.Normally Closed Contacts (N.C.): Provide a normally closed circuit when actuator is in free position.Normally Open Contacts (N.O.): Provide a normally open circuit when actuator is in free position.
Switch Types
Form Z: This breaks the circuit in two places. Also referred to as Double Break Contacts.
Form C: Switch which may either make or break a circuit, depending on how it is wired. Also re-ferred to as Single-Pole Double-Throw (SPDT).
Form A: Normaly open (N.O.) wwitch with only one moving and one stationary contact. Also referred to as Single-Pole Single-Throw (SPST).
Form A: Normaly closed (N.C.) switch with only one moving and one stationary contact.
Common Ground (NMOS): Is based on electronic circuitry. Switched output is pulled to ground when operated.
Key
V-in (grey)
V-out (white)
GND (black)
Common Plus (PMOS): Is based on electronic circuitry. Switched output is pulled to plus when operated.
IP68
10mm
19mm
Ø 21.5mm eIPOC
Mounting diameter
Outer diameter
Recommended for engraving (non-rotating button
IP Degree
Extended IP Degree
LED LED illuminated switchDepth
3
Series
Mount. D
iameter
IP Degree
LED
Switch Function
Termination
Button Type
CircuitPage N
umber
Depth
Out. D
iameter
CMI10 20mm 18mm IP65 RingDotPower
Momentary Screw2.0x0.5mm
FlatDomedRaised
Form A 14
CM10 20mm 18mm IP65 Momentary Screw2.0x0.5mm
FlatDomedRaised
Form AForm B
12
CM15 35mm 18mm IP67 MomentaryMaintained
1.8x0.4mm FlatRaised
Form C2x Form C
20
CM16 35mm 18mm IP67 MomentaryMaintained
1.8x0.4mm FlatRaised
Form C2x Form C
24
CM11 20mm 18mm IP65 Momentary Screw2.0x0.5mm
FlatRaised
Form AForm B
16
CMI15 35.7mm 18mm IP67 RingDotPower
MomentaryMaintained
1.8x0.4mm FlatRaised
Form C2x Form C
22
CMI16 35.7mm 18mm IP67 RingDot
MomentaryMaintained
1.8x0.4mm FlatRaised
Form C2x Form C
26
CMI11 20mm 16mm 18mm IP65 RingDot
Momentary 2.0x0.5mm FlatRaised
Form A 18
ES06 8.8mm10mm
21.5mm IP68eIP68C
Momentary 15cm leadsPC pins
Flat Form A 28
ES08 13.8mm 21.5mm IP68 Momentary 15cm leads Flat Form A 30
ES02 13.9mm 21.8mm MomentaryMaintained
15cm leads Flat NMOS 32
CM08 18mm 14mm IP67 Momentary 2.0x0.5mm FlatRaised
Form A 8
12mmCMI08 19mm 14mm IP67 Ring
DotMomentary 2.0x0.5mm Flat
RaisedForm A 10
ESI11 16.5mm 21.5mm Ring Momentary 15cm leads Flat Form A 3419mm
CM20 24mm 22mm IP65 Momentary Screw2.8x0.5mm
FlatDomedRaised
Form A 36
CMI20 27.3mm 22mm IP65 RingDot
Momentary Screw Flat Form A 38
4
Series
Mount. D
iameter
IP Degree
LED
Switch Function
Termination
Button Type
CircuitPage N
umber
Depth
Out. D
iameter
CMI21 27.3mm 22mm IP65 RingDot
Momentary Screw Flat Form A 42
CM25 32.1mm39.5mm
22mm IP65IP67
MomentaryMaintained
Screw2.8x0.5mm
Flat Form Z 48
CM22 19.1mm 22mm IP65 Momentary Screw2.0x0.5mm
FlatDomedRaised
Form AForm B
44
CMI25 33mm39.5mm
19mm
22mm IP65IP67
RingDotPower
MomentaryMaintained
Screw2.8x0.5mm
FlatRaised
Form Z 50
CM23 19.1mm 22mm IP65 Momentary Screw2.0x0.5mm
FlatRaised
Form AForm B
46
CM26 32.1mm39.5mm
22mm IP65IP67
MomentaryMaintained
Screw2.8x0.5mm
Flat Form Z 52
CMI26 33mm39.5mm
22mm IP65IP67
RingDot
MomentaryMaintained
Screw2.8x0.5mm
FlatRaised
Form Z 54
CM30 38mm 22mm IP67 MomentaryMaintained
2.8x0.5mm Flat Form C2x Form C
56
CM31 38mm 22mm IP67 MomentaryMaintained
2.8x0.5mm Flat Form C2x Form C
60
CMI30 38mm 22mm IP67 RingDotPower
MomentaryMaintained
2.8x0.5mm Flat Form C2x Form C
58
CMI31 38mm 22mm IP67 RingDot
MomentaryMaintained
2.8x0.5mm Flat Form C2x Form C
62
CMI35 35.3mm40.3mm
25mm IP65IP67
RingDotPower
MomentaryMaintained
2.8x0.5mm Flat Form Z 66
CM35 35.3mm40.3mm
25mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z 64
CM21 24mm 22mm IP65 Momentary Screw2.8x0.5mm
FlatRaised
Form A 40
CMI36 35.3mm40.3mm
25mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z 70
CM36 35.3mm40.3mm
22mm 25mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z 68
CM37 25.3mm 25mm IP65 Momentary 2.8x0.5mm Flat Form A 72
5
Series
Mount. D
iameter
IP Degree
LED
Switch Function
Termination
Button Type
CircuitPage N
umber
Depth
Out. D
iameter
CMI41 38.5mm40.8mm
28mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
80
CMI46 38.4mm40.8mm
32mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
88
CMI51 38.4mm40.8mm
35mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
96
CM41 38.5mm40.8mm
28mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
78
CM46 38.4mm40.8mm
32mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
86
CM51 38.4mm40.8mm
35mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
94
CMI40 38.5mm40.8mm
28mm IP65IP67
RingDotPower
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
76
CMI45 38.4mm40.8mm
32mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
84
CMI50 38.4mm40.8mm
35mm IP65IP67
RingDot
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
92
CM40 38.5mm40.8mm
28mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
74
CM45 38.4mm40.8mm
32mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
82
CM50 38.4mm40.8mm
35mm IP65IP67
MomentaryMaintained
2.8x0.5mm Flat Form Z2x Form Z
90
25mm
28mm
30mm
CM90 38.5mm 22mm 25mm IP65 MomentaryMaintained
2.8x0.5mm Flat Form C 98
CMI90 38.5mm 22mm 25mm IP65 PowerSurface
MomentaryMaintained
2.8x0.5mm Flat Form C 100
Plastic Switches
EP03 10mm 16mm 20mm IP68IP69K
Momentary 15cm leads Guided Form A 102
NK03 10mm 16mm 20mm IP68IP69K
MomentaryMaintained
15cm leads Guided NMOS 106
EPI03 10mm 16mm 20mm IP68 Dot Momentary 15cm leads Guided Form A 104
Non-moving Switches
6
Series
Mount. D
iameter
IP Degree
LED
Switch Function
Termination
Button Type
CircuitPage N
umber
Depth
Out. D
iameter
CI04 26mm 8mm 11mm IP67 Dot 1.8x0.4mm Flat 134
CI08 27.4mm 12mm 15mm IP67 Dot 1.8x0.4mm Flat 136
NK02 10mm 21.5mm IP68IP69K
MomentaryMaintained
15cm leads Flat NMOS 110
EP06 10mm 21.5mm IP68IP69K
Momentary 15cm leads Flat Form A 108
Indicators
Capacitive switches
19mm
22mm
EP08 13.8mm 21.5mm IP68 Momentary 15cm leads Flat Form A 112
EP15 17.8mm19.7mm
26mm IP68IP69K
Momentary 15cm leads FlatGuided
Form A 114
NK15 17.8mm19.7mm
26mm IP68IP69K
MomentaryMaintained
15cm leads FlatGuided
NMOS 116
EPI16 14mm 26mm IP68 Ring Momentary 15cm leads Flat Form A 120
EPI15 14mm17.8mm
26mm IP68 DotRing
Momentary 15cm leads FlatGuided
Form A 118
NKI16 14mm 26mm IP68 Ring Momentary 15cm leads Flat NMOS 122
EPI50 17.5mm 30mm 33.5mm IP68 DotRing
Momentary 15cm leads Flat Form A 124
NKI50 17.5mm 30mm 33.5mm IP68 DotRing
MomentaryMaintained
15cm leads Flat NMOS 126
CKI21 32mm 19mm 22mm IP68IP69K
Ring MomentaryMaintained
30cm leads FlatGuided
PMOS 128
CKI36 32mm 22mm 25mm IP68IP69K
Ring MomentaryMaintained
30cm leads FlatGuided
PMOS 132
CKI35 32mm 22mm 25mm IP68IP69K
Ring MomentaryMaintained
30cm leads Flat PMOS 130
Accessories
MPI-VSG
14.5mm Spring loaded
138
7
CM08 Vandalproof PushbuttonIP67 18mm 12mm Ø 14mm
SpecificationTermination Solder terminals (2.0 x 0.5mm)
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -25°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 200,000 (min)
Operating force 2.5N
Nut mounting torque 2.5Nm
Panel thickness 1.0mm to 7.0mm
Body & button material See ordering information
Contact material Silver plated brass
18 1.5
14
M12x0.75
Flat
18 3
14M12x0.75
Raised
All dimensions in mm
Product Dimensions
ø 9
Front view (all versions)
8
CM08 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
12+0.2
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A
Ordering information
Material ButtonV2: Stainless steel F: FlatAS: Aluminium black R: RaisedBN: Brass nickel plated
CM08/ / /M/S/20
9
CMI08 Vandalproof PushbuttonIP67 19mm 12mm Ø 14mm
Product Dimensions
14
19.1 1.5
M12x0.75
Flat
3
14
19.1
M12x0.75
Raised
LED
SpecificationTermination Solder terminals (2.0 x 0.5mm)
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -25°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 200,000 (min)
Operating force 2.5N
Nut mounting torque 2.5Nm
Panel thickness 1.0mm to 7.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
0.8
ø7.4
Front view (ring)ø 3.1
ø 9
Front view (dot)
10
CMI08 Vandalproof Pushbutton
Rev. 3 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Switch terminals
LED-Voltage supply
Form A
1 Dual-colour LEDs are only available without resistor.2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
Ordering information
Material Button LED LED-Colour LED-Voltage1
V2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor2 AS: Aluminium black R: Raised D: Dot RD: Red 06: 6 VoltBN: Brass nickel plated YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red1
BR: Blue/Red1
GB: Green/Blue1
CMI08/ / / / /M/S/20/
11
CM10 Vandalproof PushbuttonIP65 20.1mm 16mm Ø 18mm
SpecificationTermination Screw or 2.0x0.5 solder terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
M16x1
18
20.1 1.5
Screw terminals FlatM16x1
17.5 1.5
18Solder terminals Flat
18
3
Raised
All dimensions in mm
Product Dimensions
18
3.1
Domed
ø 11.8
Front view (all versions)
12
CM10 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A Form B
Ordering information
Material Button Switch Function TerminationsV2: Stainless steel F: Flat M: Momentary NO 20: 2.0mm solder tabsAS: Aluminium black R: Raised N: Momentary NC ST: ScrewsBN: Brass nickel plated D: DomedGB: Brass golden finish
CM10/ / / /S/
13
CMI10 Vandalproof PushbuttonIP65 16mm Ø 18mm
Product Dimensions
LED
SpecificationTermination Screw or 2.0x0.5 solder terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
M16x1
18
27.4 1.5
Screw terminals FlatM16x1
17.5 1.5
18Solder terminals Flat
18
3
Raised
18
2.8
Domed (ring)
1.2
ø 9.4
Front view(ring, flat or raised)
3.1
18
Domed (dot)
0.6
ø 10.6
Front view(ring, domed)
ø 11.8
ø 4
Front view(dot)
17.5mm
27.4mm
14
CMI10 Vandalproof Pushbutton
Rev. 4 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Switch terminals
LEDcommon LED 1
LED 2LED 3Form A
1 Only with flat button2 3 pins for LED connection (one per colour and common cathode (common anode available on request))3 No resistor: Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))4 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA5 Only available with solder terminals
Ordering information
Material Button LED LED-Colour LED-Voltage Switch Function TerminationV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor4 M: Momentary 20: 2.0mm tabsAS: Aluminium black R: Raised D: Dot RD: Red 06: 6 Volt ST: ScrewsBN: Brass nickel plated D:Domed S: Power- YL: Yellow 12: 12 Volt ring1 BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red2,5
02: Green/Blue2,5
03: Blue/Red2,5
11: RGB C-3,5
CMI10/ / / / / / /S/
Switch terminals
LED-Voltage supply
Switch terminals
LED-Voltage Supply
Screw terminals2 LED pins
Solder terminals2 LED pins
3&4 LED pins3,4
15
CM11 Vandalproof PushbuttonIP65 20.1mm 16mm Ø 18mm
SpecificationTermination Screw or 2.0x0.5 solder terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
M16x1
18
20.1 1.5
Flat
M16x118
20.1 3
Raised
All dimensions in mm
Product Dimensions
ø 11.8
Front view (all versions)
16
CM11 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A Form B
Ordering information
Material Button Switch Function TerminationV2: Stainless steel F: Flat M: Momentary NO 20: 2.0mm tabsAS: Aluminium black R: Raised N: Momentary NC ST: ScrewsBN: Brass nickel plated GB: Brass golden finish
CM11/ / / /S/
16 +0.1
1.9
-0.1
18.2 +0.1
17
CMI11 Vandalproof PushbuttonIP65 20mm 16mm Ø 18mm
Product Dimensions
M16x1
18
20 1.5
Flat
M16x1
18
20 3.4
Raised
LED
SpecificationTermination Solder terminals (2.0 x 0.5mm)
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VDC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
1.2
ø 9.4
Front view (ring)ø 4
ø 11.8
Front view (dot)
18
CMI11 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Form A
16 +0.1
1.9
-0.1
18.2 +0.1
Ordering information
Material Button LED LED-Colour LED-Voltage Switch FunctionV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor3 M: MomentaryAS: Aluminium black R: Raised D: Dot RD: Red 06: 6 VoltBN: Brass nickel plated YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red1
02: Green/Blue1
03: Blue/Red1
11: RGB C-2
CMI11/ / / / / / /S/201 3 pins for LED connection (one per colour and common cathode (common anode available on request))2 No resistor: Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available
on request))3 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
Switch terminals
LEDcommon LED 1
LED 2LED 3
Switch terminals
LED-Voltage supply
2 LED pins 3&4 LED pins1,2
19
CM15 Vandalproof PushbuttonIP67 16mm Ø 18mm
Product Dimensions
M16x1
35.7 2
18
Flat
M16x1
35.7
18
4
Raised
All dimensions in mm
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
Switching function Momentary or maintained
Configuration of üoles Single or double
Maximum load 3A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
ø 11.8
Front view (all versions)
35.7mm
20
CM15 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram Contact arrangement
Form C
Ordering information
Material Button Switch Function PolesV2: Stainless steel F: Flat M: Momentary S: SingleAS: Aluminium black R: Raised L: Maintained D: DoubleBN: Brass nickel plated
CM15/ / / / /18
21
CMI15 Vandalproof PushbuttonIP67 16mm Ø 18mm
Product Dimensions
M16x1
37
18
2
Flat
M16x1
37 4
18
Raised
LED
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 3A, 48VDC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
37mm
0.7
ø 10.4
Front view (ring)
ø 11.8
ø 5
Front view (dot)
22
CMI15 Vandalproof Pushbutton
Rev. 4 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Form C
Ordering information
Material Button LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor2 M: Momentary S: Single AS: Aluminium black R: Raised D: Dot RD: Red 06: 6 Volt L: Maintained D: DoubleBN: Brass nickel plated P: Power1 YL: Yellow 12: 12 Volt S: Power- BL: Blue 24: 24 Volt ring1 WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI15/ / / / /18/ / /1 Only with flat button2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
23
CM16 Vandalproof PushbuttonIP67 16mm Ø 18mm
Product Dimensions
M16x1
35.7 2
18
Flat
M16x1
35.7
18
4
Raised
All dimensions in mm
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
Switching function Momentary or maintained
Configuration of üoles Single or double
Maximum load 3A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
ø 11.8
Front view (all versions)
35.7mm
24
CM16 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram Contact arrangement
Form C
Ordering information
Material Button Switch Function PolesV2: Stainless steel F: Flat M: Momentary S: SingleAS: Aluminium black R: Raised L: Maintained D: DoubleBN: Brass nickel plated
CM16/ / / / /18
16 +0.1
1.9
-0.1
18.2 +0.1
25
CMI16 Vandalproof PushbuttonIP67 37mm 16mm Ø 18mm
Product Dimensions
M16x1
37
18
2
Flat
M16x1
37
18
4
Raised
LED
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 3A, 48VDC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
0.7
ø 10.4
Front view (ring)
ø 11.8
ø 5
Front view (dot)
26
CMI16 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Form C
Ordering information
Material Button LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor2 M: Momentary S: Single AS: Aluminium black R: Raised D: Dot RD: Red 06: 6 Volt L: Maintained D: DoubleBN: Brass nickel plated YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI16/ / / / /18/ / /
16 +0.1
1.9
-0.1
18.2 +0.1
1 Only with flat button2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
27
ES06 Vandalproof PushbuttonIP68 19mm Ø 21.5mm
Product Dimensions
M19x1
ø21
.5
10 1.3~150
Flying leads (brass)
All dimensions in mm
SpecificationTermination 15cm flying leads or PC pins
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 42VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529), eIPOC
Duty cycle 1,000,000 (min)
Operating force 3.3+0.6N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 4.0mm
Body & button material See ordering information
Contact material Gold
8.8 1.3
M19x1
21.5
PC pins
eIPOC
ø 15.5
Front viewM19x1
ø21
.5
~150 8.8 1.3
Flying leads (aluminium)
8.8mm
10mm
28
ES06 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Ordering information
Material Terminals
MS: Chromed brass L1: 15cm leadsAN: Natural annodised aluminium PC: PC pinsA1: Red annodised aluminium1
A2: Blue annodised aluminium1
A3: Yellow annodised aluminium1
A4: Green annodised aluminium1
ES06 F00MM
1 Code is only for button material. Housing is made of natural annodised aluminium
Form A
29
ES08 Vandalproof PushbuttonIP6813.8mm 19mm Ø 21.5mm
Product Dimensions
ø21
.5
M19x1
~150 13.8 1.3
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force 3.6+0.7N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 8.0mm
Body & button material See ordering information
Contact material Gold
ø 15.38
Front view
30
ES08 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Ordering information
MaterialAN: Natural annodised aluminiumA1: Red annodised aluminium1
A2: Blue annodised aluminium1
A3: Yellow annodised aluminium1
A4: Green annodised aluminium1
ES08 F00MML1
1 Code is only for button material. Housing is made of natural annodised aluminium
Form A
31
ES02 Vandalproof Pushbutton13.9mm 19mm Ø 21.8mm
Product Dimensions
2.5
M19x1
21.8
~150 13.9
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 2.5A, 24VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -25°C to +70°C
Duty cycle 300,000 (min)
Operating force 1.5N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 12.0mm
Body & button material See ordering information
Contact material Silver plated
32
ES02 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Ordering information
Material Switch FunctionAN: Natural annodised aluminium MS: Momentary (solid state)AR: Red enamelled aluminium1 LS: Maintained (solid state)AB: Blue enamelled aluminium1
AY: Yellow enamelled aluminium1
AG: Green enamelled aluminium1
AK: Black enamelled aluminium1
AS: Black annodised aluminium1
ES02 T00
1 Code is only for button material. Housing is made of natural annodised aluminium
L1
Common ground (NMOS)
33
ESI11 Vandalproof Pushbutton16.5mm 19mm Ø 21.5mm
Product Dimensions
M19x1
ø21
.5
~150 16.5 1.5
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 50mA, 24VDC
LED voltage See ordering information
Contact resistance 100 mΩ
Insulation resistance > 100 MΩ
Operating temperature -20°C to +70°C
Duty cycle 50,000 (min)
Operating force 1.8N
Nut mounting torque 2.5Nm
Panel thickness 1.5 to 13.0mm
Body & button material Stainless steel & PC
Contact material Gold
LED
1.8
ø 11.85
Front view
34
ESI11 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A
Ordering information
LED-Colour LED-Voltage BL: Blue 00: No resistor1
GN: Green 05: 5 volts AM: Orange 12: 12 volts RD: Red 24: 24 volts
ESI11/V2/F/R/ /M/S/L1
1 Green & Blue: 3.2 VDC Red & Orange: 2.5 VDC @20mA
/
Wiring Instructions
Switch wire
Switch wire
LED colour wire for +LED
Ground wire for LED
35
CM20 Vandalproof PushbuttonIP65 19mm Ø 22mm
Product Dimensions
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
Screw terminals FlatM19x1
22
25.3 2
Solder terminals Flat
3.6
22
Raised
All dimensions in mm
22
3.6
Domed
ø 14.9
Front view (all versions)
24mm
25.3mm
36
CM20 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A
Ordering information
Material Button TerminationsV2: Stainless steel F: Flat 28: 2.8mm tabsAS: Aluminium black R: Raised ST: ScrewsBN: Brass nickel plated D: DomedGB: Brass golden finish
CM20/ / /M/S/
37
CMI20 Vandalproof PushbuttonIP65Ø 22mm
Product Dimensions
27.3 2
22
M19x1
LED
SpecificationTermination Screw terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36DC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
19mm 27.3mm
1.8
ø 11.8
Front view (ring)
ø 15.4
ø 9.2
Front view (dot)
38
CMI20 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Switch terminals
LED voltage supply
+ -
Ordering information
Material LED LED-Colour LED-VoltageV2: Stainless steel R: Ring GN: Green 00: No resistor1
AS: Aluminium black D: Dot RD: Red 06: 6 Volt YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI20/ /F/ / M/S/ST/ /
Form A
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
39
CM21 Vandalproof PushbuttonIP65 24mm 19mm Ø 22mm
Product Dimensions
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
M19x1
22
24 2
Screw terminals Flat22
2
M19x1
25.3
Solder terminals Flat
3.6
22
Raised
All dimensions in mm
ø 14.9
Front view (all versions)
40
CM21 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A
22.2+0.1
2.4 -
0.1
19+0.1
Ordering information
Material Button TerminationsV2: Stainless steel F: Flat 28: 2.8mm tabsAS: Aluminium black R: Raised ST: ScrewsBN: Brass nickel platedGB: Brass golden finish
CM21/ / /M/S/
41
CMI21 Vandalproof PushbuttonIP65Ø 22mm
Product Dimensions
22
27.3 2
M19x1
LED
SpecificationTermination Screw terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36DC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
19mm 27.3mm
1.8
ø 11.8
Front view (ring)
ø 15.4
ø 9.2
Front view (dot)
42
CMI21 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Switch terminals
LED voltage supply
+ -
Ordering information
Material LED LED-Colour LED-VoltageV2: Stainless steel R: Ring GN: Green 00: No resistor1
AS: Aluminium black D: Dot RD: Red 06: 6 Volt YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI21/ /F/ / M/S/ST/ /
Form A
22.2+0.1
2.4 -
0.1
19+0.1
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
43
CM22 Vandalproof PushbuttonIP65 19.1mm 19mm Ø 22mm
Product Dimensions
All dimensions in mm
SpecificationTermination Screw or 2.0x0.5 solder terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
19.1 2
22
M19x1
Screw terminals Flat
M19x1
17.2 2
22Solder terminals Flat
3.6
22
Raised
22
3.6
Domed
ø 14.9
Front view (all versions)
44
CM22 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Ordering information
Material Button Switch Function TerminationsV2: Stainless steel F: Flat M: Momentary NO 20: 2.0mm tabsAS: Aluminium black R: Raised N: Momentary NC ST: Screw terminalsBN: Brass nickel plated D: Domed
CM22/ / /S/
Form A Form B
/
45
CM23 Vandalproof PushbuttonIP65 19.1mm 19mm Ø 22mm
Product Dimensions
SpecificationTermination Screw or 2.0x0.5 solder terminals
Switching function Momentary
Configuration of poles Single
Maximum load 2A, 36VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 6.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
22
2
M19x1
19.1
Screw terminals Flat22
2
M19x1
17.2
Solder terminals Flat
3.6
22
Raised
ø 14.9
Front view (all versions)
46
CM23 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
Form A Form B
22.2+0.1
2.4 -
0.1
19+0.1
Ordering information
Material Button Switch Function TerminationsV2: Stainless steel F: Flat M: Momentary NO 20: 2.0mm tabsAS: Aluminium black R: Raised N: Momentary NC ST: Screw terminalsBN: Brass nickel plated D: Domed
CM23/ / /S//
47
CM25 Vandalproof Pushbutton 19mm Ø 22mm
Product Dimensions
Solder terminals momentary
All dimensions in mm
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
Solder terminals maintained
IP65
IP67
Screw terminals momentary Screw terminals maintained
ø 15.4
Front view
32.1mm
33.5mm
38.6mm
39.5mm
48
CM25 Vandalproof Pushbutton
Rev. 3 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function TerminationV2: Stainless steel M: Momentary 28: 2.8mm tabsAS: Aluminium black L: Maintained1 ST: Screws
CM25/ /F/ /S/
Form Z
1 IP65 (EN60529)Non rotating button available on request
49
CMI25 Vandalproof PushbuttonIP65Ø 22mm
Product Dimensions
LED
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
19mm
3.7
22
Raised
IP67
Solder terminals momentary
All dimensions in mm
Solder terminals maintained
Screw terminals momentary Screw terminals maintained
1.7
ø 12
Front view (ring)
ø 15.4
ø 9
Front view (dot)
33mm
33.5mm
39.3mm
39.5mm
50
CMI25 Vandalproof Pushbutton
Rev. 5 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Ordering information
Material Button LED LED-Colour LED-Voltage Switch Function TerminationV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor3 M: Momentary 28: 2.8mm tabsAS: Aluminium black R: Raised1 D: Dot RD: Red 06: 6 Volt L: Maintained2 ST: Screws P: Power2YL: Yellow 12: 12 Volt S: Power-BL: Blue 24: 24 Volt ring2 WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI25/ / / /S/
1 Only available with ring illumination2 IP65 (EN60529)3 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mANon rotating button available on request
/ /
Form Z
/
51
CM26 Vandalproof Pushbutton 19mm Ø 22mm
Product Dimensions
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP65
IP67
M19x1
22
32.1 2
Solder terminals momentary
M19x1
22
33.5 2
All dimensions in mm
M19x1
38.6 2
22
Solder terminals maintained
M19x1
22
39.5 2
Screw terminals momentary Screw terminals maintained
ø 15.4
Front view
32.1mm
33.5mm
38.6mm
39.5mm
52
CM26 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
22.2+0.1
2.4 -
0.1
19+0.1
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function TerminationV2: Stainless steel M: Momentary 28: 2.8mm tabsAS: Aluminium black L: Maintained1 ST: Screws
CM26/ /F/ /S/
Form Z
1 IP65 (EN60529)Non rotating button available on request
53
CMI26 Vandalproof PushbuttonIP65Ø 22mm
Product Dimensions
LED
SpecificationTermination Screw or 2.8x0.5 fast connect terminals
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
19mm
IP67
22
3.7
Raised
M19x1
22
33 2
Solder terminals momentary
M19x1
22
33.5 2
All dimensions in mm
M19x1
22
39.3 2
Solder terminals maintained
M19x1
22
39.5 2
Screw terminals momentary Screw terminals maintained
1.7
ø 12
Front view (ring)
ø 15.4
ø 9
Front view (dot)
33mm
33.5mm
39.3mm
39.5mm
54
CMI26 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Ordering information
Material Button LED LED-Colour LED-Voltage Switch Function TerminationV2: Stainless steel F: Flat R: Ring GN: Green 00: No resistor3 M: Momentary 28: 2.8mm tabsAS: Aluminium black R: Raised1 D: Dot RD: Red 06: 6 Volt L: Maintained2 ST: Screws YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI26/ / / /S/
1 Only available with ring illumination2 IP65 (EN60529)3 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mANon rotating button available on request
/ /
Form Z
/
22.2+0.1
2.4 -
0.1
19+0.1
55
CM30 Vandalproof PushbuttonIP67 38mm 19mm Ø 22mm
Product Dimensions
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 3N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
ø 15.3
Front view
56
CM30 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained D: Double
CM30/ /F/ /28/
Form C
57
CMI30 Vandalproof PushbuttonIP67Ø 22mm
Product Dimensions
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 3N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
19mm 38mm
1.1
ø 13.5
Front view (ring)ø 7
ø 15.3
Front view (dot)
58
CMI30 Vandalproof Pushbutton
Rev. 4 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Circuit Diagram
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained D: Double P: Power YL: Yellow 12: 12 Volt S: Power- BL: Blue 24: 24 Volt ring WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red2
02: Green/Blue2
03: Blue/Red2
11: RGB3
CMI30/ /F/ /
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 3 pins for LED connection (one per colour and common cathode (common anode available on request))3 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))
/ / / /28
Form C
Mounting Dimensions Wiring Instructions
Switch terminals
LED-Voltage supply
NC
NO
C
+ -
Switch terminals
NC
NO
C
LED common
LED 1 LED 2
LED 3
2 LED pins 4 LED pins (RGB)3
3 LED pins (bi-colour)2
Switch terminals
NC
NO
C
LED common
LED 1 LED 2
59
CM31 Vandalproof PushbuttonIP67 38mm 19mm Ø 22mm
Product Dimensions
M19x1
22
36.7 2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 3N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
ø 15.3
Front view
60
CM31 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained D: Double
CM31/ /F/ /28/
Form C
22.2+0.1
2.4 -
0.1
19+0.1
61
CMI31 Vandalproof PushbuttonIP67Ø 22mm
Product Dimensions
M19x1
22
38 2
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Duty cycle 50,000 (min)
Operating force 3N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Silver plated brass
All dimensions in mm
19mm 38mm
1.1
ø 13.5
Front view (ring)ø 7
ø 15.4
Front view (dot)
62
CMI31 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form C
22.2+0.1
2.4 -
0.1
19+0.1
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained D: Double YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red2
02: Green/Blue2
03: Blue/Red2
11: RGB3
CMI31/ /F/ /
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 3 pins for LED connection (one per colour and common cathode (common anode available on request))3 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))
/ / / /28
Wiring Instructions
Switch terminals
LED-Voltage supply
NC
NO
C
+ -
Switch terminals
NC
NO
C
LED common
LED 1 LED 2
LED 3
2 LED pins 4 LED pins (RGB)3
3 LED pins (bi-colour)2
Switch terminals
NC
NO
C
LED common
LED 1 LED 2
63
CM35 Vandalproof PushbuttonIP65 22mm Ø 25mm
Product Dimensions
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 8.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary Maintained
ø 18
Front view (all versions)
35.3mm
40.3mm
64
CM35 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
1
2
3
4
All dimensions in mm
Ordering information
Material Switch FunctionV2: Stainless steel M: MomentaryAS: Aluminium black L: Maintained1
CM35/ /F/ /S/28
1 IP65 (EN60529)Non rotating button available on request
Form Z
65
CMI35 Vandalproof PushbuttonØ 25mm
Product Dimensions
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 8.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
22mm IP65
IP67
Momentary Maintained
2
ø 14
Front view (ring)ø 9
ø 18
Front view (dot)
35.3mm
40.3mm
66
CMI35 Vandalproof Pushbutton
Rev. 5 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Wiring Instructions
Ordering information
Material LED LED-Colour LED-Voltage Switch FunctionV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: MomentaryAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2
S: Power- YL: Yellow 12: 12 Volt ring2 BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
CMI35/ /F/ / / / /S/28
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
Form Z LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
67
CM36 Vandalproof PushbuttonIP65 22mm Ø 25mm
Product Dimensions
M22x1
25
35.3 2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 8.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary
M22x1
25
40.3 2
Maintained
ø 18
Front view (all versions)
35.3mm
40.3mm
68
CM36 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
1
2
3
4
All dimensions in mm
Ordering information
Material Switch FunctionV2: Stainless steel M: MomentaryAS: Aluminium black L: Maintained1
CM36/ /F/ /S/28
1 IP65 (EN60529)Non rotating button available on request
Form Z2.
2-0
.1
22+0.1
25.2+0.1
69
CMI36 Vandalproof PushbuttonØ 25mm
Product Dimensions
M22x1
25
35.3 2
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 8.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
22mm IP65
IP67
Momentary Maintained
M22x125
40.3 2
2
ø 14
Front view (ring)ø 9
ø 18
Front view (dot)
35.3mm
40.3mm
70
CMI36 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form Z2.
2-0
.1
22+0.1
25.2+0.1
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
Ordering information
Material LED LED-Colour LED-Voltage Switch FunctionV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: MomentaryAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2
YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
CMI36/ /F/ / / / /S/28
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
71
CM37 Vandalproof PushbuttonIP65 22mm Ø 25mm
Product Dimensions
25
M22x1
25.3 2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single
Maximum load 2A, 36VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP65 (EN 60529)
Duty cycle 200,000 (min)
Operating force 4N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Silver plated
25.3mm
ø 18
Front view
72
CM37 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram
All dimensions in mm
Ordering information
MaterialV2: Stainless steelAS: Aluminium black
CM37/ /F/M/S/28
Form A
73
CM40 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary Maintained
ø 19.8
Front view (all versions)
38.5mm
40.8mm
74
CM40 Vandalproof Pushbutton
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM40/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z
75
CMI40 Vandalproof PushbuttonØ 28mm
Product Dimensions
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
25mm IP65
IP67
Momentary Maintained
2
ø 18.7
Front view (ring)ø 9
ø 22.7
Front view (dot)
38.5mm
40.8mm
76
CMI40 Vandalproof Pushbutton
Rev. 5 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Circuit Diagram
CMI40/ /F/ / / / /28/
Form Z
Mounting Dimensions Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double S: Power- YL: Yellow 12: 12 Volt ring2 BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
77
CM41 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
M25x1
28
38.5 2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
MomentaryM25x1
28
40.8 2
Maintained
ø 19.8
Front view (all versions)
38.5mm
40.8mm
78
CM41 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM41/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z2.
4-0
.1
25+0.1
28.2+0.1
79
CMI41 Vandalproof PushbuttonØ 28mm
Product Dimensions
M25x1
28
38.5 2
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
25mm IP65
IP67
Momentary Maintained
M25x128
40.8 2
2
ø 15.8
Front view (ring)ø 9
ø 19.8
Front view (dot)
38.5mm
40.8mm
80
CMI41 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form Z2.
4-0
.1
25+0.1
28.2+0.1
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
CMI41/ /F/ / / / /28/
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
81
CM45 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
38.4
32
M28x1.5
2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary32
M28x1.5
40.8 2
Maintained
ø 22.7
Front view
38.4mm
40.8mm
82
CM45 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
ø28+0.1
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM45/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z
83
CMI45 Vandalproof PushbuttonØ 28mm
Product Dimensions
32
M28x1.5
38.4 2
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
25mm IP65
IP67
Momentary Maintained32
M28x1.5
40.8 2
2
ø 18.7
Front view (ring)ø 9
ø 22.7
Front view (dot)
38.4mm
40.8mm
84
CMI45 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
ø28+0.1
Mounting DimensionsCircuit Diagram
Form Z
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
CMI45/ /F/ / / / /28/
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double S: Power- YL: Yellow 12: 12 Volt ring2 BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
85
CM46 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
32
M28x1.5
238.4
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary
32M28x1.5
240.8
Maintained
ø 22.7
Front view
38.4mm
40.8mm
86
CM46 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM46/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z2.
4-0
.1
28+0.1
32.2+0.1
87
CMI46 Vandalproof PushbuttonØ 28mm
Product Dimensions
M28x1.5
32
238.4
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
25mm IP65
IP67
Momentary Maintained32
M28x1.5
240.8
2
ø 18.7
Front view (ring)ø 9
ø 22.7
Front view (dot)
38.4mm
40.8mm
88
CMI46 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form Z2.
4-0
.1
28+0.1
32.2+0.1
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
CMI46/ /F/ / / / /28/
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
89
CM50 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
38.4
M30x1.5
35
2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary
40.8
M30x1.535
2
Maintained
ø 24.7
Front view
38.4mm
40.8mm
90
CM50 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
ø30+0.1
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM50/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z
91
CMI50 Vandalproof PushbuttonØ 35mm
Product Dimensions
38.4
M30x1.5
35
2
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
30mm IP65
IP67
Momentary Maintained
40.8
M30x1.5
35
2
2
ø 20.7
Front view (ring)ø 9
ø 24.7
Front view (dot)
38.4mm
40.8mm
92
CMI50 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
ø30+0.1
Mounting DimensionsCircuit Diagram
Form Z
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
CMI50/ /F/ / / / /28/
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double S: Power- YL: Yellow 12: 12 Volt ring2 BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
93
CM51 Vandalproof PushbuttonIP65 25mm Ø 28mm
Product Dimensions
2
35
38.4
M30x1.5
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0 to 10.0mm
Body & button material See ordering information
Contact material Gold plated
IP67
Momentary
2
35
40.8
M30x1.5
Maintained
ø 24.7
Front view
38.4mm
40.8mm
94
CM51 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting DimensionsCircuit Diagram Contact arrangement
All dimensions in mm
Ordering information
Material Switch Function PolesV2: Stainless steel M: Momentary S: SingleAS: Aluminium black L: Maintained1 D: Double
CM51/ /F/ /28/
1 IP65 (EN60529)Non rotating button available on request
Form Z2.
4-0
.1
30+0.1
35.2+0.1
95
CMI51 Vandalproof PushbuttonØ 28mm
Product Dimensions
M30x1.5
35
238.4
LED
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 5A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529) maintained: IP65
Duty cycle 50,000 (min)
Operating force 5.5N
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body & button material See ordering information
Contact material Gold plated
All dimensions in mm
25mm IP65
IP67
Momentary Maintained
M30x1.5
35
240.8
2
ø 20.7
Front view (ring)ø 9
ø 24.7
Front view (dot)
38.4mm
40.8mm
96
CMI51 Vandalproof Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form Z2.
4-0
.1
30+0.1
35.2+0.1
Wiring Instructions
LEDcommonLED 1LED 3LED 2
2 LED pins 3&4 LED pins3,4
CMI51/ /F/ / / / /28/
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesV2: Stainless steel R: Ring GN: Green 00: No resistor1 M: Momentary S: SingleAS: Aluminium black D: Dot RD: Red 06: 6 Volt L: Maintained2 D: Double YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue 01: Green/Red3
02: Green/Blue3
03: Blue/Red3
11: RGB4
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA2 IP65 (EN60529)3 3 pins for LED connection (one per colour and common cathode (common anode available on request))4 Red/Green/Blue, 4 pins for LED connection (one per colour and common cathode (common anode available on request))Non rotating button available on request
97
CM90 Plastic Pushbutton
Product Dimensions
37.3
M16x1
25
2
All dimensions in mm
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 1A, 48VAC
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -25°C to +85°C
Ingress protection IP65 (EN 60529)
Duty cycle 50,000 (min)
Operating force 1-4N
Panel thickness 0.5 to 6.0mm
Body & button material See ordering information
Contact material Silver plated
Ø 25mm 22mm IP65 37.3mm
ø 18
Front view
98
CM90 Plastic Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Ordering information
Material Switch Function PolesPB: Black plastic M: Momentary S: SinglePS: Silver plastic L: Maintained D: Double
CM90/ /F/ /28/
Circuit Diagram
Form C
Mounting Dimensions Contact arrangement
99
CMI90 Plastic PushbuttonØ 25mm
Product Dimensions
M16x1
25
38.5 2
SpecificationTermination Fast connect terminals (2.8x0.5mm)
Switching function Momentary or maintained
Configuration of poles Single or double
Maximum load 1A, 48VAC
LED voltage See ordering information
Contact resistance < 50 mΩ
Insulation resistance > 1000 MΩ
Operating temperature -25°C to +85°C
Ingress protection IP65 (EN 60529)
Duty cycle 50,000 (min)
Operating force 1-4N
Panel thickness 0.5mm to 6.0mm
Body & button material PC
Contact material Silver plated
All dimensions in mm
22mm IP65 LED 38.5mm
ø 18
Front view (surface)
100
CMI90 Plastic Pushbutton
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Circuit Diagram
Ordering information
Material LED LED-Colour LED-Voltage Switch Function PolesPB: Black plastic P: Power1 GN: Green 00: No resistor2 M: Momentary S: SinglePS: Silver plastic F: Surface RD: Red 06: 6 Volt L: Maintained D: Double YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CMI90/ /F/ / / / /28/
Form C
Mounting Dimensions Wiring Instructions
Switch terminals
LED-Voltage supply
NC
NO
C
+ -
1 Only with silver plastic2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
101
EP03 Piezo SwitchIP6810mm 16mm Ø 20mm
Product Dimensions
1.2~150 10
20
M16x0.5
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 8.0mm
Body & button material See ordering information
IP69K
ø 16
Front view (ring)
102
EP03 Piezo Switch
Rev. 5 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EP03/ /G/M/S/L1
Form A
Ordering information
Material AN: Natural annodised aluminiumAR: Red annodised aluminiumAB: Blue annodised aluminiumAY: Yellow annodised aluminiumAG: Green annodised aluminium
103
EPI03 Illuminated Piezo Switch
~150
20
10 1.2
M16x0.5
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
LED voltage Red & Yellow: 1.9V; Green & Blue: 3.4V;
White: 3,6V (20mA)
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 8.0mm
Body & button material See ordering information
IP6810mm 16mm Ø 20mm
ø 6
ø 16
Front view
104
EPI03 Illuminated Piezo Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
15.4+0.10
16+
0.10
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EPI03/ /G/D/
Form A
Wiring Instructions
Switch wire
Switch wire
LED colour wire for +LED
Ground wire for LED
/00/M/S/L1
Ordering information
Material LED-Colour AN: Natural annodised aluminium BL: BlueAR: Red annodised aluminium BR: Blue/RedAB: Blue annodised aluminium BW: Blue/WhiteAY: Yellow annodised aluminium GB: Green/BlueAG: Green annodised aluminium GN: Green GR: Green/Red RD: Red WH: White YL: Yellow
105
NK03 thiNKswitchTM
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary or toggle
Configuration of poles Single
Maximum load 2.5A, 8VDC to 24VDC
“On” resistance 100 mΩ
Insulation resistance > 109 MΩ
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Impulse time 0.5 sec. (Momentary)
Operating force < 5N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 8.0mm
Body & button material See ordering information
All dimensions in mm
16mm IP6810mmØ 20mm
IP69K
1.2~150 10
20
M16x0.5
ø 16
Front view
106
NK03 thiNKswitchTM
Rev. 2 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Timing Diagram
Power on Start delay OFF
Reacts to pressure
ON
[ON Time
0.5 sec]
OFF
Momentary
Power on Start delay Stored status
from EEPROM
Reacts to pressure
ON
Reacts to pressure
OFF
ToggleCommon ground (NMOS)
NK03/ /S/L1
Ordering information
Material Switch function AN: Natural annodised aluminium M: MomentaryAR: Red annodised aluminium T: ToggleAB: Blue annodised aluminium AY: Yellow annodised aluminium AG: Green annodised aluminiumBC: Brass chrome platedV2: Stainless steel
/G/
107
EP06 Piezo SwitchØ 21.5mm
21.5
M19x1
~150 10 1.3
All dimensions in mm
19mm 10mm
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 8.0mm
Body & button material See ordering information
IP68
IP69K
ø 18
Front view
108
EP06 Piezo Switch
Rev. 3 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram
Form A
EP06/ /F/M/S/L1
Ordering information
Material V2: Stainless steelBC: Brass chrome plated
109
NK02 thiNKswitchTM Ø 21.5mm
Product Dimensions
21.5
M19x1
~150 10 1.3
SpecificationTermination 15cm flying leads
Switching function Momentary or toggle
Configuration of poles Single
Maximum load 2.5A, 8VDC to 24VDC
“On” resistance 100 mΩ
Insulation resistance > 109 MΩ
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Impulse time 0.5 sec. (Momentary)
Operating force <3N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 4.0mm
Body & button material See ordering information
All dimensions in mm
19mm 10mm IP68
IP69K
ø 18
Front view
110
NK02 thiNKswitchTM
Rev. 3 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
Mounting DimensionsCircuit Diagram Timing Diagram
Ordering information
Material Switch FunctionV2N: Stainless steel MO: MomentaryBCN: Brass chrome TO: Toggle
NK02 T
Power on Start delay OFF
Reacts to pressure
ON
[ON Time
0.5 sec]
OFF
Momentary
Power on Start delay Stored status
from EEPROM
Reacts to pressure
ON
Reacts to pressure
OFF
ToggleCommon ground (NMOS)
111
EP08 Piezo SwitchIP6813.8mm 19mm Ø 21.5mm
Product Dimensions
21.5
~150 13.8 1.3
M19x1
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 11.0mm
Body & button material See ordering information
ø 16
Front view
112
EP08 Piezo Switch
Rev. 3 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EP08/ /F/M/S/L1
1 Code is only for button material. Housing is made of natural annodised aluminium
Form A
Ordering information
Material AN: Natural annodised aluminiumAR: Red annodised aluminium1
AB: Blue annodised aluminium1
AY: Yellow annodised aluminium1
AG: Green annodised aluminium1
113
EP15 Piezo SwitchIP6817.8mm 22mm Ø 26mm
Product Dimensions
M22x1
26
17.8 1.2~150
All dimensions in mm
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5 to 13.0mm
Body & button material See ordering information
IP69KØ 25mm
M22x1
25
~150 19.7 1.3
18.4mm
Finger guided Flat
ø 20.5
Front view (guided)
114
EP15 Piezo Switch
Rev. 5 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EP15/ /
Form A
Ordering information
Material Head Style AN: Natural annodised aluminium F: FlatAR: Red annodised aluminium G: Finger guidedAB: Blue annodised aluminiumAY: Yellow annodised aluminiumAG: Green annodised aluminium
/M/S/L1
1.4 +
0.1
ø 25.1 +0.1
ø 22 +0.1
115
NK15 thiNKswitchTM
IP6817.8mm 22mm Ø 26mm
Product Dimensions
M22x1
26
17.8 1.2~150
All dimensions in mm
IP69KØ 25mm
M22x1
25
~150 19.7 1.3
18.4mm
Finger guided Flat
ø 20.5
Front view (guided)
SpecificationTermination 15cm flying leads
Switching function Momentary or toggle
Configuration of poles Single
Maximum load 2.5A, 8VDC to 24VDC
“On” resistance 100 mΩ
Insulation resistance > 109 MΩ
Operating temperature -40°C to +85°C
Ingress protection IP66, IP68 (EN 60529); IP69K (DIN 4050)
Duty cycle 1,000,000 (min)
Impulse time 0.5 sec. (Momentary)
Operating force <3N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
116
NK15 thiNKswitchTM
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
All dimensions in mm
NK15/ /S/L1
Ordering information
Material Head Style Switch function AN: Natural annodised aluminium F: Flat M: MomentaryAR: Red annodised aluminium G: Guided T: ToggleAB: Blue annodised aluminium AY: Yellow annodised aluminium AG: Green annodised aluminiumBC: Brass chrome platedV2: Stainless steel
/ /
Mounting DimensionsCircuit Diagram Timing Diagram
Power on Start delay OFF
Reacts to pressure
ON
[ON Time
0.5 sec]
OFF
Momentary
Power on Start delay Stored status
from EEPROM
Reacts to pressure
ON
Reacts to pressure
OFF
ToggleCommon ground (NMOS)
1.4 +
0.1
ø 25.1 +0.1
ø 22 +0.1
117
EPI15 Illuminated Piezo SwitchIP6814mm 22mm Ø 26mm
ø 3
ø 20.51.20.75
ø26
M22x1
~150 17.8
7
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
LED voltage See ordering information
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force < 3N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
Finger guided
ø 16
2M22x1
26
~150 14 2
Flat
17.8mm
ø 3
7
ø 24.5
118
EPI15 Illuminated Piezo Switch
Rev. 6 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
21.15+0.10
22+
0.10
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EPI15/ /
Form A
Wiring Instructions
Switch wire
Switch wire
LED colour wire for +LED
Ground wire for LED
/M/S/L1
Ordering information
Material Head Style LED-Type LED-Colour LED-Voltage AN: Natural annodised aluminium F: Flat D: Dot BL: Blue 00: No resistor3
AR: Red annodised aluminium G: Finger guided R: Ring1 BR: Blue/Red2 05: 5 voltsAB: Blue annodised aluminium BW: Blue/White2 12: 12 voltsAY: Yellow annodised aluminium GB: Green/Blue2 24: 24 voltsAG: Green annodised aluminium GN: GreenV2: Stainless steel GR: Green/Red2
RD: Red WH: White YL: Yellow
/ / /1 Only with flat head and 24 volt LED2 Only ring LED, left and right3 Red & Yellow: 1.9V; Green & Blue: 3.4V; White: 3,6V (20mA)
1.4 +
0.1
ø 25.1 +0.1
ø 22 +0.1
119
EPI16 Illuminated Piezo SwitchIP6814mm 22mm Ø 26mm
ø 18
1M22x1
26
~150 14 2
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC
LED voltage See ordering information
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
ESD resistance 15kV to front of switch
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force < 5N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
120
EPI16 Illuminated Piezo Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EPI16/
Form A
Wiring Instructions
Switch wire
Switch wire
LED colour wire for +LED
Ground wire for LED
/M/S/L1
Ordering information
Material LED-Colour LED-Voltage AN: Natural annodised aluminium BL: Blue 00: No resistor1
AR: Red annodised aluminium BR: Blue/Red R1: 5-12 voltsAB: Blue annodised aluminium BW: Blue/WhiteAY: Yellow annodised aluminium GB: Green/BlueAG: Green annodised aluminium GN: GreenV2: Stainless steel GR: Green/Red RD: Red WH: White YL: Yellow
/1 Red & Yellow: 1.9V; Green & Blue: 3.4V; White: 3,6V (20mA)
/F/R/
121
NKI16 Illuminated thiNKswitchTM
IP6814mm 22mm Ø 26mm
ø 18
1M22x1
26
~150 14 2
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 15cm flying leads
Switching function Momentary or toggle
Configuration of poles Single
Maximum load 2.5A, 8VDC to 24VDC
LED voltage See ordering information
“On” resistance 100 mΩ
Insulation resistance > 109 Ω
ESD resistance 15kV to front of switch
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Impulse time 0.5 sec. (Momentary)
Operating force < 5N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
122
NKI16 Illuminated thiNKswitchTM
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram
NKI16/ /S/L1
Ordering information
Material LED-Colour LED-Voltage Switch function AN: Natural annodised aluminium BL: Blue 00: No resistor1 M: MomentaryAR: Red annodised aluminium BR: Blue/Red 05: 5 volts T: ToggleAB: Blue annodised aluminium BW: Blue/White 12: 12 voltsAY: Yellow annodised aluminium GB: Green/Blue 24: 24 voltsAG: Green annodised aluminium GN: GreenV2: Stainless steel GR: Green/Red RD: Red WH: White YL: Yellow
/1 Red & Yellow: 1.9V; Green & Blue: 3.4V; White: 3,6V (20mA)
/F/R/
Timing Diagram
Power on Start delay OFF
Reacts to pressure
ON
[ON Time
0.5 sec]
OFF
Momentary
Power on Start delay Stored status
from EEPROM
Reacts to pressure
ON
Reacts to pressure
OFF
Toggle
Pink: +ve supply+ve supplyfor load
Load
White
Brown: common -ve
Common ground (NMOS)
Wiring Instructions
Switch: see circuit diagram
Ground wire for LED
LED colour wire for +LED
/
123
EPI50 Illuminated Piezo SwitchIP6819mm 30mm Ø 33.5mm
1.5
33.5
17.5~200
M30x1.5
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 20cm flying leads
Switching function Momentary
Configuration of poles Single
Maximum load 100mA, 35VDC, 24VAC
LED voltage 24V AC/DC (20mA)
Contact resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Operating force < 5N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
1.75
ø 21.5
124
EPI50 Illuminated Piezo Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
ø30+0.1
Mounting Dimensions
All dimensions in mm
Circuit Diagram
EPI50/ /F/R/
Form A
Wiring Instructions
Switch wire
Switch wire
LED colour wire for +LED
Ground wire for LED
/24/M/S/L2
Ordering information
Material LED-Colour AN: Natural annodised aluminium BL: BlueAR: Red annodised aluminium BR: Blue/RedAB: Blue annodised aluminium BW: Blue/WhiteAY: Yellow annodised aluminium GB: Green/BlueAG: Green annodised aluminium GN: GreenV2: Stainless steel GR: Green/Red RD: Red WH: White YL: Yellow
1.6
+0.
1
ø 33.6 +0.1
ø 30 +0.1
125
NKI50 Illuminated thiNKswitchTM
IP6819mm 30mm Ø 33.5mm
1.5
33.5
17.5~200
M30x1.5
All dimensions in mm
LED
Product Dimensions
1.75
ø 21.5
SpecificationTermination 20cm flying leads
Switching function Momentary or toggle
Configuration of poles Single
Maximum load 2.5A, 8VDC to 24VDC
LED voltage 24 volts DC
“On” resistance 100 mΩ
Insulation resistance > 109 Ω
Operating temperature -40°C to +50°C
Ingress protection IP68 (EN 60529)
Duty cycle 1,000,000 (min)
Impulse time 0.5 sec. (Momentary)
Operating force < 5N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 13.0mm
Body & button material See ordering information
126
NKI50 Illuminated thiNKswitchTM
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
ø30+0.1
Mounting Dimensions
All dimensions in mm
NKI50/ /S/L2
Ordering information
Material LED-Colour Switch function AN: Natural annodised aluminium BL: Blue M: MomentaryAR: Red annodised aluminium BR: Blue/Red T: ToggleAB: Blue annodised aluminium BW: Blue/WhiteAY: Yellow annodised aluminium GB: Green/BlueAG: Green annodised aluminium GN: GreenV2: Stainless steel GR: Green/Red RD: Red WH: White YL: Yellow
/24//F/R/
Circuit Diagram Timing Diagram
Power on Start delay OFF
Reacts to pressure
ON
[ON Time
0.5 sec]
OFF
Momentary
Power on Start delay Stored status
from EEPROM
Reacts to pressure
ON
Reacts to pressure
OFF
Toggle
Pink: +ve supply+ve supplyfor load
Load
White
Brown: common -ve
Common ground (NMOS)
Wiring Instructions
Switch: see circuit diagram
Ground wire for LED
LED colour wire for +LED
1.6
+0.
1
ø 33.6 +0.1
ø 30 +0.1
127
CKI21 Illuminated Capacitive SwitchIP6832mm 19mm Ø 22mm
ø22
0.4
1~300
M19x1
1.2
ø 13.5
32
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 30cm flying leads
Switching function Momentary or Maintained
Configuration of poles Single
Maximum load 500mA, 24VDC
LED voltage See ordering informations
Contact resistance 200mΩ
Insulation resistance 600VDC 10MΩ
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529) & IP69K (DIN 4050)
Duty cycle 50,000,000 (min)
Operating force 0N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 8.0mm
Body & button material Stainless steel
Can be triggered by water
IP69K
Finger guided
Flat
M19x1
ø22
1~300 1.2
ø 13.5
32
128
CKI21 Illuminated Capacitive Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram Wiring Instructions
Switch: see circuit diagram
LED wire +1
LED wire –1
Ordering information
Head Style LED-Colour LED-Voltage Switch Function F: Flat BL: Blue 00: No resistor2 M: MomentaryG: Finger guided GN: Green 05: 5 Volt L: Maintained RD: Red 12: 12 Volt 1: Momentary switched LED3
WH: White 24: 24 Volt 2: Maintained switched LED3
YL: Yellow BG: Blue/Green BR: Blue/Red LED-Colour BW: Blue/White 01: Green/Red4
RG: Red/Green 02: Green/Blue4
RB: Red/Blue 03: Blue/Red4
GB: Green/Blue 04: Blue/White4
GR: Green/Red 11: RGB5
WB: White/Blue NB: Off/Blue NG: Off/Green NR: Off/Red NW: Off/White NY: Off/Yellow
V-in (grey)
V-out (white)
GND (black)
Common plus (PMOS)
CKI21/V2/ /R/ /S/L3/ /1 LED wires are only present by unswitched LED versions2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA3 First colour is active when the switch is not pressed. Second colour is active when switch is pressed4 3 wires for LED connection (one per colour and common cathode (common anode available on request))5 Red/Green/Blue, 4 wires for LED connection (one per colour and common cathode (common anode available on request))
For versions with 3&4 LED wires there is one wire per colour (+) and a black wire as common cathode4,5
1.3 +
0.1
19 +0.1
22.2 +0.1
129
CKI35 Illuminated Capacitive SwitchIP6832mm 22mm Ø 25mm
ø25
M22x1
2.41~300
ø 13.5
32
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 30cm flying leads
Switching function Momentary or Maintained
Configuration of poles Single
Maximum load 500mA, 24VDC
LED voltage See ordering informations
Contact resistance 200mΩ
Insulation resistance 600VDC 10MΩ
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529) & IP69K (DIN 4050)
Duty cycle 50,000,000 (min)
Operating force 0N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 8.0mm
Body & button material Stainless steel
Can be triggered by water
IP69K
130
CKI35 Illuminated Capacitive Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram Wiring Instructions
Switch: see circuit diagram
LED wire +1
LED wire –1
V-in (grey)
V-out (white)
GND (black)
Common plus (PMOS)
Ordering information
LED-Colour LED-Voltage Switch Function BL: Blue 00: No resistor2 M: Momentary GN: Green 05: 5 Volt L: Maintained RD: Red 12: 12 Volt 1: Momentary switched LED3
WH: White 24: 24 Volt 2: Maintained switched LED3
YL: Yellow BG: Blue/Green BR: Blue/Red LED-Colour BW: Blue/White 01: Green/Red4
RG: Red/Green 02: Green/Blue4
RB: Red/Blue 03: Blue/Red4
GB: Green/Blue 04: Blue/White4
GR: Green/Red 11: RGB5
WB: White/Blue NB: Off/Blue NG: Off/Green NR: Off/Red NW: Off/White NY: Off/Yellow
CKI35/V2/F/R/ /S/L3/ /
For versions with 3&4 LED wires there is one wire per colour (+) and a black wire as common cathode4,5
1 LED wires are only present by unswitched LED versions2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA3 First colour is active when the switch is not pressed. Second colour is active when switch is pressed4 3 wires for LED connection (one per colour and common cathode (common anode available on request))5 Red/Green/Blue, 4 wires for LED connection (one per colour and common cathode (common anode available on request))
131
CKI36 Illuminated Capacitive SwitchIP6832mm 22mm Ø 25mm
ø25
M22x1 0.4
2.41~300
ø 13.5
32
All dimensions in mm
LED
Product Dimensions
SpecificationTermination 30cm flying leads
Switching function Momentary or Maintained
Configuration of poles Single
Maximum load 500mA, 24VDC
LED voltage See ordering informations
Contact resistance 200mΩ
Insulation resistance 600VDC 10MΩ
Operating temperature -40°C to +85°C
Ingress protection IP68 (EN 60529) & IP69K (DIN 4050)
Duty cycle 50,000,000 (min)
Operating force 0N
Nut mounting torque 2.5Nm
Panel thickness 0.5mm to 8.0mm
Body & button material Stainless steel
Can be triggered by water
IP69K
Finger guided
Flat
ø25
M22x1
2.41~300
ø 13.5
32
132
CKI36 Illuminated Capacitive Switch
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Circuit Diagram Wiring Instructions
Switch: see circuit diagram
LED wire +1
LED wire –1
V-in (grey)
V-out (white)
GND (black)
Common plus (PMOS)
Ordering information
Head Style LED-Colour LED-Voltage Switch Function F: Flat BL: Blue 00: No resistor2 M: MomentaryG: Finger guided GN: Green 05: 5 Volt L: Maintained RD: Red 12: 12 Volt 1: Momentary switched LED3
WH: White 24: 24 Volt 2: Maintained switched LED3
YL: Yellow BG: Blue/Green BR: Blue/Red LED-Colour BW: Blue/White 01: Green/Red4
RG: Red/Green 02: Green/Blue4
RB: Red/Blue 03: Blue/Red4
GB: Green/Blue 04: Blue/White4
GR: Green/Red 11: RGB5
WB: White/Blue NB: Off/Blue NG: Off/Green NR: Off/Red NW: Off/White NY: Off/Yellow
CKI36/V2/ /R/ /S/L3/ /
For versions with 3&4 LED wires there is one wire per colour (+) and a black wire as common cathode4,5
1.3 +
0.1
22 +0.1
25.2 +0.1
1 LED wires are only present by unswitched LED versions2 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA3 First colour is active when the switch is not pressed. Second colour is active when switch is pressed4 3 wires for LED connection (one per colour and common cathode (common anode available on request))5 Red/Green/Blue, 4 wires for LED connection (one per colour and common cathode (common anode available on request))
133
CI04 Vandalproof LEDIP67 26mm 8mm Ø 11mm
Product Dimensions
M8x0.75
11
1.526
All dimensions in mm
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
LED voltage See ordering information
Rated current 15mA
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body material See ordering information
134
CI04 Vandalproof LED
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
Ordering information
Material LED-Colour LED-VoltageV2: Stainless steel GN: Green 00: No resistor1
BN: Brass nickel plated RD: Red 06: 6 Volt YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
CI04/ /P/D/ / /18
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
135
CI08 Vandalproof LEDIP67 27.4mm 12mm Ø 15mm
Product Dimensions
M12x1
15
1.527.4
All dimensions in mm
SpecificationTermination Fast connect terminals (1.8 x 0.4mm)
LED voltage See ordering information
Rated current 15mA
Operating temperature -20°C to +55°C
Ingress protection IP67 (EN 60529)
Nut mounting torque 5Nm to 14Nm
Panel thickness 1.0mm to 10.0mm
Body material See ordering information
136
CI08 Vandalproof LED
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Mounting Dimensions
All dimensions in mm
CI08/ /P/D/ / /18
Ordering information
Material LED-Colour LED-VoltageV2: Stainless steel GN: Green 00: No resistor1
BN: Brass nickel plated RD: Red 06: 6 Volt YL: Yellow 12: 12 Volt BL: Blue 24: 24 Volt WH: White GR: Green/Red BR: Blue/Red GB: Green/Blue
1 Green,Yellow: 1.8V Red,Blue,White: 2.8V @20mA
137
MPI-VSG Electronic Ballast
Product Dimensions
SpecificationTermination Spring loaded terminals
Input voltage 8-30VDC or 8-24VAC
Output 15-20mA
Protects the LED from excessive voltage
Constant current source with transient protection
All dimensions in mm
14.5mm
K- A+Uin LED
ø 3
2.5
2.5
20
13.6
23
14.7
Front Side
14.5
6
14.5
6
Top
138
MPI-VSG Electronic Ballast
Rev. 1 · maschenta-design.de · Engelking retains the right to change the specifications at any time without prior notice.
Connection diagram for 4-wire systems
Part Number
MPI-VSG
Uin+ -
MPI-VSG
Switch terminals
LED terminals+ -
Connection diagram for 2-wire systems
Uin+ -
MPI-VSG
Voltagesupply
LED terminals+ -
139
Engelking Elektronik GmbHAlbstraße 1678609 TuningenGermanyTel.: +49 7464 9865 0 Fax: +49 7464 9865 71 Email: [email protected] Web: www.engelking.de