Download - Design of Steel Frames - BS 5950
-
8/8/2019 Design of Steel Frames - BS 5950
1/46
IIDESIGN PROCEDURE FOR STEELFRAME STRUCTURES ACCORDING
TO BS 5950
2.1 IntroductionStructural design is grossly abbreviated name of an operation, which for major projectsmay involve the knowledge of hundreds of experts from a variety of disciplines. A codeof practice may therefore be regarded as a consensus of what is considered acceptable atthe time it was written, containing a balance between accepted practice and recentresearch presented in such a way that the information should be of immediate use to thedesign engineer. As such, it is regarded more as an aid to design, which includesallowable stress levels, member capacities, design formulae and recommendations forgood practice, rather than a manual or textbook on design.
Once the decision has been taken to construct a particular building, a suitablestructural system must be selected. Attention is then given to the way in which loads areto be resisted. After that, critical loading patterns must be determined to suit the purposeof the building. There is, therefore, a fundamental two-stage process in the designoperation. Firstly, the forces acting on the structural members and joints are determinedby conducting a structural system analysis, and, secondly, the sizes of various structural
-
8/8/2019 Design of Steel Frames - BS 5950
2/46
Design Procedure for Steel Frame Structures according toBS 5950 27
members and details of the structural joints are selected by checking against
specification member-capacity formulae.Section 2.2 starts with definitions of basic limit-states terminology. Then,
determination of loads, load factors, and load combinations are given as requested bythe British codes of practice BS 6399. Accordingly, ultimate limit state designdocuments of structural elements are described. In this, the discussion is extended tocover the strength, stability and serviceability requirements of the British code ofpractice BS 5950: Part 1. Finally, the chapter ends by describing methods used, in thepresent study, to represent the charts of the effective length factor of column in sway ornon-sway frames in a computer code.
2.2 Limit state concept and partial safety factorsLimit state theory includes principles from the elastic and plastic theories and
incorporates other relevant factors to give as realistic a basis for design as possible. Thefollowing concepts, listed by many authors, among them McCormac (1995), Nethercot(1995), Ambrose (1997), and MacGinley (1997), are central to the limit state theory:1. account is taken of all separate design conditions that could cause failure or make
the structure unfit for its intended use,2. the design is based on the actual behaviour of materials in structures and the
performance of real structures, established by tests and long-term observations,3. the overall intention is that design is to be based on statistical methods and
probability theory and4. separate partial factors of safety for loads and for materials are specified.
-
8/8/2019 Design of Steel Frames - BS 5950
3/46
Design Procedure for Steel Frame Structures according toBS 5950 28
The limiting conditions given in Table 2.1 are normally grouped under two
headings: ultimate or safety limit states and serviceability limit states. The attainment ofultimate limit states (ULS) may be regarded as an inability to sustain any increase inload. Serviceability limit states (SLS) checks against the need for remedial action orsome other loss of utility. Thus ULS are conditions to be avoided whilst SLS could beconsidered as merely undesirable. Since a limit state approach to design involves the useof a number of specialist terms, simple definitions of the more important of these areprovided by Nethercot (1995).
Table 2.1. Limit states (taken from BS 5950: Part 1)Ultimate States Serviceability states
1. Strength (including general yielding, 5. Deflectionrupture, buckling and transformationinto mechanism) 6 . Vibration (e.g. wind inducedoscillation
2. Stability against overturning and sway 7. Repairable damage due to fatigue3 . Fracture due to fatigue 8 . Corrosion and durability4. Brittle fracture
Figure 2.1 shows how limit-state design employs separate factors rf ' whichreflect the combination of variability of loading rl'material strength r m and structuralperformance r p . Inthe elastic design approach, the design stress is achieved by scalingdown the strength of material or member using a factor of safety r e as indicated inFigure 2.1, while the plastic design compares actual structural member stresses with theeffects of factored-up loading by using a load factor of r p .
-
8/8/2019 Design of Steel Frames - BS 5950
4/46
Design Procedure for Steel Frame Structures according toBS 5950 29
Numerical values
Strength of materialor of member
Stresses or stress resultantsdue to working loadsElastic design
Plastic design
+ rmLimit state design
Figure 2.1. Level for different design methods at whichcalculations are conducted (Nethercot, 1995)
BS 5950 deliberately adopts a very simple interpretation of the partial safety factorconcept in using only three separate /"factors: Variability of loading r , : loads may be greater than expected; also loads used to
counteract the overturning of a structure (see section 2.6) may be less than intended. Variability of material strength r m : the strength of the material in the actual
structure may vary from the strength used in calculations. Variability of structural performance rp: The structure may not be as strong as
assumed in the design because of the variation in the dimensions of members,variability of workmanship and differences between the simplified idealisationnecessary for analysis and the actual behaviour of the real structure.
A value of 1.2 has been adopted for rp which, when multiplied by the values selectedfor r, (approximately 1.17 for dead load and 1.25 for live load) leads to the values of
-
8/8/2019 Design of Steel Frames - BS 5950
5/46
Design Procedure for Steel Frame Structures according toBS 5950 30
rf' which is then applied to the working loads, examples of which are discussed inSection 2.3. Values of r m have been incorporated directly into the design strengthsgiven in BS 5950. Consequently, the designer needs only to consider rf values in theanalysis.
2.3 Loads and load combinationsAssessment of the design loads for a structure consists of identifying the forces due toboth natural and designer-made effects, which the structure must withstand, and thenassigning suitable values to them. Frequently, several different forms of loading must beconsidered, acting either singly or in combination, although in some cases the mostunfavourable situation can be easily identifiable. For buildings, the usual forms ofloading include dead load, live load and wind load. Loads due to temperature effects andearthquakes, in certain parts of the world, should be considered. Other types of structure
will have their own special forms of loading, for instance, moving live loads and theircorresponding horizontal loads (e.g. braking forces on bridges or braking force due tothe horizontal movement of cranes). When assessing the loads acting on a structure, it isusually necessary to make reference to BS 6399: Part 1,2, and 3, in which basic data ondead, live and wind loads are given.
2.3.1 Dead loadDetermination of dead load requires estimation of the weight of the structural memberstogether with its associated "non-structural" component. Therefore, in addition to thebare steelwork, the weights of floor slabs, partition walls, ceiling, plaster finishes andothers (e.g. heating systems, air conditions, ducts, etc) must all be considered. Sincecertain values of these dead loads will not be known until after at least a tentative design
-
8/8/2019 Design of Steel Frames - BS 5950
6/46
Design Procedure for Steel Frame Structures according toBS 5950 31
is available, designers normally approximate values based on experience for their initial
calculations. A preliminarily value of 6-10 kN/m2 for the dead load can be taken.2.3.2 Live load
Live load in buildings covers items such as occupancy by people, office floor loading,and movable equipment within the building. Clearly, values will be appropriate fordifferent forms of building-domestic, offices, garage, etc. The effects of snow, ice arenormally included in this category. BS 6399: Part 1 gives a minimum value of the liveload according to the purpose of the structural usage (see BS 6399: Part 1).
2.3.3 Wind load
The load produced on a structure by the action of the wind is a dynamic effect. Inpractice, it is normal for most types of structures to treat this as an equivalent static load.Therefore, starting from the basic speed for the geographical location underconsideration, suitably corrected to allow for the effects of factors such as topography,ground roughness and length of exposure to the wind, a dynamic pressure is determined.This is then converted into a force on the surface of the structure using pressure or forcecoefficients, which depend on the building'S shape.InBS 6399: Part 2, for all structures less than 100 m in height and where the wind
loading can be represented by equivalent static loads, the wind loading can be obtainedby using one or a combination of the following methods: standard method uses a simplified procedure to obtain a standard effective wind
speed, which is used with standard pressure coefficients to determine the wind loads,
directional method in which effective wind speeds and pressure coefficients aredetermined to derive the wind loads for each wind direction.
-
8/8/2019 Design of Steel Frames - BS 5950
7/46
Design Procedure for Steel Frame Structures according toBS 5950 32
The outline of the procedure, for calculating wind loads, is illustrated by the flow
chart given in Figure 2.2. This shows the stages of the standard method (most widelyused method) as indicated by the heavily outlined boxes connected by thick lines. Thestages of the directional method are shown as boxes outlined with double lines and aredirectly equivalent to the stages of the standard method.
The wind loads should be calculated for each of the loaded areas underconsideration, depending on the dimensions of the building. These may be:
the structure as a whole, parts of the structure, such as walls and roofs, or
individual structural components, including cladding units and their fixings.The standard method requires assessment for orthogonal load cases for wind
directions normal to the faces of the building. When the building is doubly-symmetric,e.g. rectangular-plan with flat, equal-duopitch or hipped roof, the two orthogonal casesshown in Figure 2.3 are sufficient. When the building is singly-symmetric, threeorthogonal cases are required. When the building is asymmetric, four orthogonal casesare required.In order to calculate the wind loads, the designer should start first with evaluating thedynamic pressure
(2.1)
where V e is the effective wind speed (m/s), which can be calculated fromV e = VsSb
where Vs is the site wind speed and Sb is the terrain and building factor.(2.2)
-
8/8/2019 Design of Steel Frames - BS 5950
8/46
Design Procedure for Steel Frame Structures according toBS 5950 33
Stage 1:Dynamic augmentation factor Input building height H , input buildingc; . . . . . type factorl
Stage 2: Check limits of applicability No ... Building is dynamic. This part doesC r< 0.25, H < 300 m II""" not apply
lYesStage 3: Basic wind speed Vb . . . I Basic wind speed map IlStage 4: Site wind speed Vs . . . Altitude factor Sa , directional factorSd , seasonal factor S,l
Stage 5: Terrain categories, effective Site terrain type, level of upwindheight He . . . . rooftops Ho, separation of buildings X1
Stage 6: Choice of method . . . Directional and topographic effects. . . . s: T e o S 1'. Sh
lStage 7: Standard effective wind . . . Directional effective wind speed Vespeed Ve1Stage 8: Dynamic pressure qs Dynamic pressure qe, qil ~rStage 9: Standard pressure . . . . Directional pressure coefficients C pcoefficients C pi, C pelStage 10: Wind loads P Directional wind loads P
Figure 2.2. Flow chart illustrating outline procedure for the determination of the windloads (according to BS 6399: Part 2)
-
8/8/2019 Design of Steel Frames - BS 5950
9/46
Design Procedure for Steel Frame Structures according toBS 5950 34
The terrain and building factor Sb is determined directly from Table 4 of BS
6399: Part 2 depending on the effective height of the building and the closest distance tothe sea.
The site wind speed Vs is calculated by
(2.3)where Vb is the basic wind speed, Sa is the altitude factor, Sd is the directional factor,S, is the seasonal factor and Sp is the probability factor.
The basic wind speed Vb can be estimated from the geographical variation givenin Figure 6 ofBS 6399: Part 2.
The altitude factor Sa depends on whether topography is considered to besignificant or not, as indicated in Figure 7 of BS 6399: Part 2. When topography is notconsidered significant, by considering L i s , the site altitude (in meters above mean sealevel), Sa should be calculated from
(2.4)The directional factor Sd is utilised to adjust the basic wind speed to produce
wind speeds with the same risk of being exceeded in any wind direction. Table 3 ofBS6399: Part 2 gives the appropriate values of Sd . Generally, when the orientation of the
building is unknown, the value of Sd may be taken as 1.The seasonal factor S, is employed to reduce the basic wind speed for buildings,
which are expected to be exposed to the wind for specific subannual periods. Basically,for permanent buildings and buildings exposed to the wind for a continuous period ofmore than 6 months a value of 1 should be used for Ss.
-
8/8/2019 Design of Steel Frames - BS 5950
10/46
Design Procedure for Steel Frame Structures according toBS 5950 35
The probability factor Sp is used to change the risk of the basic wind speed being
exceeded from the standard value annually, or in the stated subannual period if S, isalso used. For normal design applications, Sp may take a value of 1.
The second step of calculating the wind loads is evaluating the net surfacepressure P is
P=P e - Pi (2.5)
where P e and Pi are the external and internal pressures acting on the surfaces of abuilding respectively.
The external pressure P e is
(2.6)
while the internal surface-pressure Pi is evaluated by
(2.7)
where Ca is the size effect factor, Cpe is the external pressure coefficient and Cpi isthe internal pressure coefficient.
Values of pressure coefficient Cpe and Cpi for walls (windward and leewardfaces) are given in Table 5 ofBS 6399: Part 2 according to the proportional dimensionsof the building as shown in Figure 2.3 and Figure 2.4. In these figures, the buildingsurfaces are divided into different zones (A, B, C, and D). Each of these zone has adifferent value of Cpe and Cpi as given in Table 5 ofBS 6399: Part 2.
Values of size effect factor C; are given in Figure 4 ofBS 6399: Part 2 in whichthe diagonal dimension (a) of the largest diagonal area to the building category is
-
8/8/2019 Design of Steel Frames - BS 5950
11/46
Design Procedure for Steel Frame Structures according toBS 5950 36
considered. The category of the building depends on the effective height of the building
and the closest distance between the building and the sea. C; takes values between 0.5and 1.0.
The third step of calculating the wind loads is to determine the value of the load Pusmg
P =pA. (2.8)
Alternatively, the load P can be to compute by
(2.9)
where LPf is the summation horizontal component of the surface loads acting on thewindward-facing walls and roofs, L~ is the summation of horizontal component ofthe surface loads acting on the leeward-facing walls and roofs and C, is the dynamicaugmentation factor which determined depending on the reference height of the buildingHi: The factor 0.85 accounts for the non-simultaneous action between faces.
-
8/8/2019 Design of Steel Frames - BS 5950
12/46
Design Procedure for Steel Frame Structures according toBS 5950 37
Plan Plan
Wind
Wind.
1+---- D----'.~I
_ _ _ _ _ _ _ 1 1
T lD ~DnA B H=Hr BI5 I -r-A B C
: .
(a) Load cases: wind on long face and wind on short face
Elevation of side faceWind. W d
Building with D 5 B Building with D > BPlan
-t
D
C
A I B I AW i n d t I+- BI4 - - - + I
(b) key to pressure coefficient zonesFigure 2.3. Key to wall and flat roof pressure data
H=Hr
IBI21
-
8/8/2019 Design of Steel Frames - BS 5950
13/46
Design Procedure for Steel Frame Structures according toBS 5950 38
HT Wind ~2=Hr A B Ca
(a) Cut-out downwind: tall part
T WindB A I I 1 I In; l_! c B A H2=j"(b) Cut-out upwind: tall part long
-r- T r TWind ... WindHI B A HItt, A B u,
jTc C B A H2=Hr~
l < i 0.84 Us (2.13)where ~ and Us are yield strength and ultimate tensile strength. Alternatively, Py canbe determined according to the flange thickness as given in Table 2.4. In case of slendercross sections, Py should be evaluated by multiplying the values given in Table 2.4 by areduction factor taken from Table 8 ofBS 5950: Part 1.
Table 2.4. Design strengthSteel Grade Thickness less than or Design strengthequal to (mm) e, (N/mm2)
16 27540 26543 63 255100 245
2.5.1 Shear strengthBS 5950: Part 1 requires that the shear force F; is not greater than shear capacity PyThis can be formulated as
-
8/8/2019 Design of Steel Frames - BS 5950
19/46
Design Procedure for Steel Frame Structures according toBS 5950 44
(2.14)
The shear capacity P ; can be evaluated by(2.15)
where Ay is the shear area and can be taken as given in Table 2.5 considering the cross-sectional dimensions (t, d, D, B) shown in Figure 2.5.
Table 2.5. Shear areaSection Type Ay
Rolled I, H and channel sections tDBuilt-up sections tdSolid bars and plates O.9A gRectangular hollow sections [D/(D+B)]A gCircular hollow sections O.6A gAny other section O.9A g
D1 0 ( B 11 yT I I I1T
X d X D
1_ _ _ _ . ~t
1y(b) Rolled beams and columns(a) Circular hollow section (CHS)
Figure 2.5. Dimensions of sections
-
8/8/2019 Design of Steel Frames - BS 5950
20/46
Design Procedure for Steel Frame Structures according toBS 5950 45
When the depth to the thickness ratio of a web of rolled section becomes
(2.16)
the section should be checked for shear buckling usingF_v ~1Vc r (2.17)
where Vc r is the shear resistance that can be evaluated by(2.18)
In this equation, the critical shear strength qcr can be appropriately obtained fromTables 21(a) to (d) ofBS 5950: Part 1.
2.5.2 Tension members with momentsAny member subjected to bending moment and normal tension force should be checkedfor lateral torsional buckling and capacity to withstand the combined effects of axialload and moment at the points of greatest bending and axial loads. Figure 2.6 illustratesthe type of three-dimensional interaction surface that controls the ultimate strength ofsteel members under combined biaxial bending and axial force. Each axis represents asingle load component of normal force F, bending about the X and Y axes of the section( M x or My) and each plane corresponds to the interaction of two components.
Figure 2.6. Interaction surface of the ultimate strength under combined loading
-
8/8/2019 Design of Steel Frames - BS 5950
21/46
Design Procedure for Steel Frame Structures according toBS 5950 46
2.5.2.1 Local capacity checkUsually, the points of greatest bending and axial loads are either at the middle or ends ofmembers under consideration. Hence, the member can be checked as follows:
(2.19)
where F is the applied axial load in member under consideration, M x and My are theapplied moment about the major and minor axes at critical region, Mex and Mcv arethe moment capacity about the major and minor axes in the absence of axial load and Aeis the effective area.
The effective area Ae can be obtained byif KeAn :5Agif KeAn > Ag (2.20)
where K; is factor and can be taken as 1.2 for grade 40 or 43, Ag is the gross area takenfrom relevant standard tables, and An is the net area and can be determined by
nr pA n = Ag -L Ai
i=1(2.21)
where Ai is the area of the hole number i, and n~is the number of holes.
The moment capacity Mex can be evaluated according to whether the value ofshear load is low or high. The moment capacity Mex with low shear load can beidentified when
F-_v-:51.0.6Pv (2.22)
-
8/8/2019 Design of Steel Frames - BS 5950
22/46
Design Procedure for Steel Frame Structures according toBS 5950 47
Hence, Mex should be taken according to the classification of the cross section as
follows: for plastic or compact sections
if PySX s 1.2pyZxif PySX > 1.2pyZx' (2.23)
for semi-compact or slender sections(2.24)
where Sx is the plastic modulus of the section about the X-axis, and Zx is the elasticmodulus of the section about the X-axis.
The moment capacity Mex with high shear load can be defmed whenF--y->1.O.6Py (2.25)
Accordingly, Mex is for plastic or compact sections
if Py(Sx -Syq)::;1.2pyZxif plSx -Syq) > 1.2pyZx (2.26)
where S; is taken as the plastic modulus of the shear area Ay for sections with equalflanges and
(2.27)
for semi-compact or slender sections(2.28)
The moment capacity Mcv can be similarly evaluated as Mex by using therelevant plastic modulus and elastic modulus of the section under consideration.
-
8/8/2019 Design of Steel Frames - BS 5950
23/46
Design Procedure for Steel Frame Structures according toBS 5950 48
2.5.2.2 Lateral torsional buckling checkFor equal flanged rolled sections, in each length between lateral restraints, theequivalent uniform moment M is should not exceed the buckling resistance momentMb. This can be expressed as
(2.29)
The buckling resistance moment Mb can be evaluated for members with at leastone axis of symmetry using
(2.30)where Pb is the bending strength and can be determined from Table 11 of BS 5950 inwhich the equivalent slenderness (Au) and Py are used.
The equivalent slenderness ~T is
~T =nuvll. (2.31)where n is the slenderness correction factor, u is the buckling parameters, v is theslenderness factor and II. is the minor axis slenderness.
The slenderness factor v can be determined from Table 14 of BS 5950 accordingto the vale of II. and torsional index of the section.
The minor axis slenderness
(2.32)
should not exceed those values given in Table 2.6, where Leff is the effective length,
and ry is the radius of gyration about the minor axis of the member and may be takenfrom the published catalogues.
-
8/8/2019 Design of Steel Frames - BS 5950
24/46
Design Procedure for Steel Frame Structures according toBS 5950 49
Table 2.6. Slenderness limits
Description LimitsFor members resisting loads other than wind loads A-~1180For members resisting self weight and wind load only A-~1250For any member normally acting as a tie but subject A-~lto reversal of stress resulting from the action of wind 350
The equivalent uniform moment M can be calculated as(2.33)
where MA is the maximum moment on the member or the portion of the member underconsideration and m is an equivalent uniform factor determined either by Table 18 ofBS 5950: Part I or using
Q).57 + 0.33p + 0.10p2 if 0.57 + 0.33P + 0.10p2 ~ 0.43m =D (2.34)D0.43 if 0.57 + 0.33P + 0.10 p2 < 0.43
where p is the end moment ratios as shown in Figure 2.7.
M~PMp positive p negative
Figure 2.7. Determination of the end moment ratio (P)
-
8/8/2019 Design of Steel Frames - BS 5950
25/46
Design Procedure for Steel Frame Structures according toBS 5950 50
2.5.3 Compression members with momentsCompression members should be checked for local capacity at the points of greatestbending moment and axial load usually at the ends or middle. This capacity may belimited either by yielding or local buckling depending on the section properties. Themember should also be checked for overall buckling. These checks can be describedusing the simplified approach illustrated in the following sections.
2.5.3.1 Local capacity checkThe appropriate relationship given below should be satisfied.
(2.35)
where the parameters F , M x . My, Ag, Py' M ex- and M cv are defined in Section2.5.2.1.
2.5.3.2 Overall buckling checkThe following relationship should be satisfied:
F u; u;--+--+--~1AgPC u, PyZy (2.36)
where Pc is the compressive strength and may be obtained from Table 27a, b, c and dofBS 5950.
2.6 Stability limits
Generally, it is assumed that the structure as a whole will remain stable, from thecommencement of erection until demolition and that where the erected members areincapable of keeping themselves in equilibrium then sufficient external bracing will be
-
8/8/2019 Design of Steel Frames - BS 5950
26/46
Design Procedure for Steel Frame Structures according toBS 5950 51
provided for stability. The designer should consider overall frame stability, which
embraces stability against sway and overturning.2.6.1 Stability against overturning
The factored loads considered separately and in combination, should not cause thestructure or any part of the structure including its seating foundations to fail byoverturning, a situation, which can occur when designing tall or cantilever structures.
2.6.2 Stability against swayStructures should also have adequate stiffuess against sway. A multi-storey frameworkmay be classed as non-sway whether or not it is braced if its sway is such that secondarymoments due to non-verticality of columns can be neglected.
Sway stiffuess may be provided by an effective bracing system, increasing thebending stiffness of the frame members or the provision oflift shaft, shear walls, etc.
To ensure stability against sway, in addition to designing for applied horizontalloads, a separate check should be carried out for notional horizontal forces. Thesenotional forces arise from practical imperfections such as lack of verticality and shouldbe taken as the greater of: 1% of factored dead load from that level, applied horizontally; 0.5% of factored dead and imposed loads from that level, applied horizontally.
The effect of instability has been reflected on the design problem by using eitherthe extended simple design method or the amplified sway design method. The extendedsimple design method is the most used method in which the effective lengths ofcolumns in the plane of the frame are obtained as described in section 2.6.2.2.Determining the effective lengths of columns which is, in essence, equivalent to
-
8/8/2019 Design of Steel Frames - BS 5950
27/46
Design Procedure for Steel Frame Structures according toBS 5950 52
carrying out a stability analysis for one segment of a frame and this must be repeated for
all segments. The amplified sway design method is based on work done by Horne(1975). In this method, the bending moments due to horizontal loading should beamplified by the factor
(2.37)
where A c r is the critical load factor and can be approximated by
A = 1cr 200 s.max
(2.38)
Inthis equation, is the largest value for any storey of the sway indexs.max
(2.39)
where hi is the storey height, AUmem and AL mem are the horizontal displacements of thenc nctop and bottom of a column as shown in Figure 2.5.Inamplified sway design method, the code requires that the effective length of the
columns in the plane of the frame may be retained at the basic value of the actualcolumn length.
2.6.2.1 Classification into sway Inon-sway frameBS 5950: Part 1 differentiates between sway and non-sway frames by considering themagnitude of the horizontal deflection A i of each storey due to the application of a setof notional horizontal loads. The value of A i can therefore be formulated as
(2.40)
This reflects the lateral stiffness of the frame and includes the influence of verticalloading. If the actual frame is unclad or is clad and the stiffness of the cladding is taken
-
8/8/2019 Design of Steel Frames - BS 5950
28/46
Design Procedure for Steel Frame Structures according toBS 5950 53
into account in the analysis, the frame may be considered to be non-sway if Ili' for
every storey, is governed byh.1 1 .
-
8/8/2019 Design of Steel Frames - BS 5950
29/46
Design Procedure for Steel Frame Structures according toBS 5950 54
5950) is derived has considered not only rotations at the column ends but also the
freedom to sway. Utilising the restraint coefficients kJ and k2 evaluated from
(2.43)
The value of the effective length factor L~f / L may be interpolated from theplotted contour lines given in either Figure 23 of BS 5950 established for a column innon-sway framework or Figure 24 of BS 5950 prepared for a column in swayframework.
- - - - - - - - - - - - - - . _
IIIIIIII
KT J r _ - - - - - - - _ t T R m _I ------ ~--..;I".
i!W@i : " -IIIIIIIIIIII/ ---------- ~-
I ~:;l.o K " KBR '.BL I
IKL !II,,
~~
IKc=-L
__,I,,,,
II\\\\\
___)
----- ---
\\\\; ),II-__ I
IKc=-L L
- - - - - - - - - - - - \KBL " KBR\\\\KL I,,,II,
(a) Limited frame for a non-sway frame (b) Limited frame for a sway frame
Figure 2.9. Limited frame for a non-sway and sway frames
When using Figure 23 and 24 ofBS 5950, the following points should be noted.1. Any member not present or not rigidly connected to the column under consideration
should be allotted a K value of zero.
-
8/8/2019 Design of Steel Frames - BS 5950
30/46
Design Procedure for Steel Frame Structures according toBS 5950 55
2. Any restraining member required to carry more than 90% of its moment capacity
(reduced for the presence of axial load if appropriate) should be allotted a K value ofzero.
3. If either end of the column being designed is required to carry more than 90% of itsmoment-carrying capacity the value of kJ or k2 should be taken as 1.
4. If the column is not rigidly connected to the foundation, k2 is taken as minimalrestraint value equal to 0.9, unless the column is actually pinned (therebydeliberately preventing restraint), when k2 equals to 1.
5. If the column is rigidly connected to a suitable foundation (i.e. one which canprovide restraint), k2 should be taken 0.5, unless the foundation can be shown toprovide more restraint enabling a lower (more beneficial) value of k2 to be used.
The first three conditions reflect the lack of rotational continuity due to plasticityencroaching into the cross-section and the consequent loss of elastic stiffness, whichmight otherwise be mobilized in preventing instability.
Three additional features, which must be noted when employing these charts,namely the value of beam stiffness K b to be adopted. In the basic analysis from whichthe charts were derived it was assumed that the ends of the beams remote from thecolumn being designed were encastre (Steel Construction Institute, 1988). This is nothowever always appropriate and guidance on modified beam stiffness values is listed asfollows:1. For sway and non-sway cases, for beams, which are directly supporting a concrete
floor slab, it is recommended that Kb should be taken as fbi L for the member.
-
8/8/2019 Design of Steel Frames - BS 5950
31/46
Design Procedure for Steel Frame Structures according toBS 5950 56
2. For a rectilinear frame not covered by concrete slab and which is reasonably regular
in layout:a) For non-sway frames, where it can be expected that single curvature bending will
occur in the beam as indicated Figure 2.1Oa,Kb should be taken as 0.51b / L .
b) For sway frames, where it can be expected that double-curvature bending will existas indicated in Figure 2.10b, the operative beam stiffness will be increased and Kbshould be taken as 0.51b/L. A rider is added to this clause which notes that wherethe in-plane effective length has a significant influence on the design then it may bepreferable to obtain the effective lengths from the critical load factor A cr . Thisreflects the approximate nature of the charts and the greater accuracy possible fromcritical load calculation.
3. For structures where some resistance to sidesway is provided by partial sway bracing
or by the presence of infill panels, two other charts are given. One for the situationwhere the relative stiffness of the bracing to that of the structure denoted by k3 is 1and the second where k3 =2.
I
( ) )\ \ r
(a) Buckling mode of non-sway frame (b) Buckling mode of sway frame
Figure 2.10. Critical buckling modes of frame (taken from BS 5950)
-
8/8/2019 Design of Steel Frames - BS 5950
32/46
Design Procedure for Steel Frame Structures according toBS 5950 57
2.7 Flowchart of design procedureFigure 2.11 shows the limit state design procedure for a structural framework.
Apply notional horizontal loading condition, compute horizontalnodal displacements and determine whether the framework is
sway or non-sway
Compute the effective buckling lengths
Apply loading condition q =1, 2,A ,Q: if the framework is sway,then include the notional horizontal loading condition
Analyze the framework, compute normal force, shearing forceand bending moments for each member of the framework
Design of member nmem= 1, 2,A ,Nmem
Determine the type of the section (compact or semi-compact orcompact or slender) utilising Table 7 ofBS 5950
Evaluate the design strength of the member
Check the slenderness criteria
Figure 2.11a. Flowchart of design procedure of structural steelwork
-
8/8/2019 Design of Steel Frames - BS 5950
33/46
Design Procedure/or Steel Frame Structures according toBS 5950 58
Local capacity check
Lateral torsional bucklingcheck
Local capacity check
Compute the horizontal and vert ical nodal displacements due to thespecified loading conditions for the serviceability criteria
Check the serviceability criteria
Overall capacity check
No
Figure 2.Uh. (cont.) Flowchart of design procedure of structural steelwork
Carry out the check of shear andshear buckling if necessary.
No
-
8/8/2019 Design of Steel Frames - BS 5950
34/46
Design Procedure/or Steel Frame Structures according toBS 5950 59
2.8 Computer based techniques for the determination of theeffective length factor
The values of the effective length factor given in Figures 23 and 24 of BS 5950 areobtained when the condition of vanishing determinantal form of the unknown of theequilibrium equations is satisfied (see Chapter 3). The slope deflection method for thestability analysis is used (see Wood 1974a). This method is based on trial and errortechnique. Accordingly, it is difficult to link such this method to design optimizationalgorithm. Therefore, to incorporate the determination of the effective length factorL~f / L for a column in either sway or non-sway framework into a computer basedalgorithm for steelwork design, two techniques are presented. These techniques aredescribed in the following sections.
2.8.1 Technique 1: Digitizing the chartsIt can be seen that each of these figures is symmetric about one of its diagonal thus,digitizing a half of the plot will be sufficient. The following procedure is applied.Step 1. The charts have been magnified to twice their size as given in BS 5950: Part 1.Step 2. Each axis (k, and k2) is divided into 100 equal divisions, resulting in 101values {O.O,0.01, ... , 1.0} for each restraining coefficient.Step 3. More contour lines have been added to get a good approximation for each chart.Step 4. The value of L~f /L was read for each pair (k" k2) of values according to thedivision mentioned above. These are graphically represented as shown in Figures 2.12and 2.13 for non-sway and sway charts respectively. InFigure 2.13, values of L~f / Lgreater than 5 are not plotted.
-
8/8/2019 Design of Steel Frames - BS 5950
35/46
Design Procedure/or Steel Frame Structures according toBS 5950 60
Step 5. Two arrays, named S for sway and NS for non-sway, are created each of them is
a two-dimensional array of 101 by 101 elements. These arrays contain the 10201digitized values of Lep/ L .Step 6. The calculated values (kl and k2) applying equation (2.43) are multiplied by100, and the resulting values are approximated to the nearest higher integer numbersnamed kl h and k~ . The value of Lep /L may then be taken from the arrays as
for a column in a sway framefor a column in a non - sway frame. (2.44)
-
8/8/2019 Design of Steel Frames - BS 5950
36/46
Design Procedure/or Steel Frame Structures according toBS 5950 61
1.0
0.2 02 0.40.0 .
0.9
0.8Le;!L 0.7
0.6
0.5
Figure 2.12. Surface plot of the restraint coefficients kl and k2 versus Le;! / L fora column ina rigid-jointed non-sway frame
5.0
4.0
I :f 3.0L2.0
O2 0 2 0.4. 0.0 .
Figure 2.13. Surface plot of the restraint coefficients kl and k2 versus L~f /L fora column a rigid-jointed sway frame
-
8/8/2019 Design of Steel Frames - BS 5950
37/46
Design Procedure/or Steel Frame Structures according toBS 5950 62
2.8.2 Technique 2: Analytical descriptions of the chartsIn this section, polynomials are obtained applying two methodologies. Firstly, astatistical package for social sciences named SPSS is used. Secondly, the geneticprogramming methodology is employed.
2.8.2.1 Regression analysisIn this section, polynomials are assumed and their parameters are obtained by applyingthe Levenberg-Marquart method modeled in SPSS (1996). Several textbooks discussand give FORTRAN code for this method among them Press et al. (1992). SPSS is ageneral-purpose statistical package, which is used for analysing data. In this context,pairs of (k" k2) and their corresponding L~f /L values are used to form polynomials,which can then be tested. A guide to data analysis using SPSS is given by Norusis(1996). The procedure used can be described as follows:Step 1. The charts are magnified to twice as their size as established in BS 5950.Step 2. Each axis (k, and k2) are divided into 20 equal divisions. This results in 21values [0.0, 0.05, ... , 1.0] for each axis. More contour lines are then added to each chart.Hence, the value of L~f /L was approximated for each pair (k" k2) according to thedivision given above.Step 3. The data SPSS data file is prepared. Here, the dependent L~f /L andindependent (k" k2) variables and the analysis type (linear or nonlinear) is chosen.Step 4. A general shape of a polynomial is assumed. The general forms
(2.45)
-
8/8/2019 Design of Steel Frames - BS 5950
38/46
Design Procedure/or Steel Frame Structures according toBS 5950 63
(2.46)
Leffx 2 2-- = ao + a1k l + a2k2 + a3kl + a4k2 + a5klk2 +La6kfk z + a7klk; + a8k~ + a9k~ + a lOk l4+auki +a12 k~kz +a13klk~ +al4klZk j
(2.47)
are utilised to express the 2nd, 3rd and 4t h order polynomials, where ao , aJ , ... , an are the
parameters.Step 5. Carrying out the analysis by examining relationships between the dependent andindependent variables and testing the hypotheses (see Norusis, 1996).Step 6. Accepting the obtained results or repeat steps 4 and 5.
When applying the proposed technique to achieve polynomials of Le:/ L of acolumn in sway framework, a poor performance of testing the hypotheses is performedbecause the infinity values of Le.f / L is estimated. This occurs when either of thecolumn ends becomes pinned. Thus, values of L~f /L greater than 5 are truncated andthe technique is repeated.
For a column in non-sway framework, the obtained polynomials of L~f /L arelisted in Table 2.7. Table 2.8 comprises polynomials for a column in sway framework.
The 4 th order polynomials are depicted as shown in Figures 2.14 and 2.15 for a columnin non-sway and sway framework respectively. The sum of square of the differencesSUMdiff between the calculated (Le: / L J;,ca! and read (Le: / L J;,dig is
z. 441 J e f f D B L eff D Dsuu==L x D _ x D D
;=1 L B,ca! B L B,dig (2.48)
-
8/8/2019 Design of Steel Frames - BS 5950
39/46
Design Procedure/or Steel Frame Structures according toBS 5950 64
Table 2.7. Polynomials obtained for Le.! /L ofa column in a non-sway frame
Equation SUMdiffLeff~ = 0.50562 + 0.11803 kl + 0.11803 k2 + 0.00025L
0.0772 k12+ 0.0772 k; + 0.094815 klk2Leff~ = 0.499363 + 0.l34267 kl + 0.l34267 k2 + 0.1098 k~ +L 0.000736
0.1098 k; - 0.0302258 kl k2 + 0.06252 k~ k2 +233
0.06252 kl k2 - 0.042576 kl - 0.042576 k2Leff~=0.51496+0.1129124kl +0.1129124k2 +L
0.185809 k12+ 0.185809 k; - 0.0005816 klk2 + 0.0005792 2 30.015352 kl k2 + 0.015352 kl k2 - 0.1343541 kl -
0.l343541 ki + 0.032573 k14+ 0.032573 ki +3 3 2 20.053263 kl k2 + 0.053263 kl k2 - 0.032727 kl k2
Table 2.S. Polynomials obtained for L~f /L of a column in a sway frame
Equation SUMdiffLeff~ = 0.78173 + 1.78797 kl + 1.78797 k2 - 2.93426 k12-L 1.80862.93426 k; - 3.822909 kl k2 + 2.629751 k~ k2 +
2.629751 kl k; + 2.36469 kt + 2.36469 kiLeff~ = 1.14112 -1.32226 kl -1.32226 k2 + 5.5268 k~ +L
2 25.5268 k2 + 7.00754 kl k2 -10.41008 kl k2 - 0.55540623310.41008 kl k2 - 6.91641 kl - 6.91641 k2 +
3.579345 k14+ 3.579345 ki + 5.22176 kt k2 +3225.22176 kl k2 + 5.89349 kl k2
-
8/8/2019 Design of Steel Frames - BS 5950
40/46
Design Procedure/or Steel Frame Structures according toBS 5950 65
1.0
0.9
L~f 0.8L
0.7
0.6
0.5
0.4 0.0 0.2 0.40.2
(a) Surface plot
Pinned 1.00.90.8t 0.70.6
k z 0.50.40.30.20.1
Fixed 0.00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0Fixed Pinned
(b) Contour plot
Figure 2.14. Graphical representation of the 4thorder polynomial of Lt /Lfora column in a rigid-jointed non-sway frame
-
8/8/2019 Design of Steel Frames - BS 5950
41/46
Design Procedure/or Steel Frame Structures according toBS 5950 66
5.0
4.0
I J 1 . fL 3.0
2.0
1.0
0.4 0.2 0.0 0.2
(a) Surface plot
q,Pinned 1.0
0.9
0.8t 0.70.6k2 0.5
0.40.30.20.1
Fixed 0.00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0Fixed Pinned
(b) Contour plot
Figure 2.15. Graphical representation of 4thorder polynomial of Lt /Lfora column ina rigid-jointed non-sway frame
-
8/8/2019 Design of Steel Frames - BS 5950
42/46
Design Procedure/or Steel Frame Structures according toBS 5950 67
From Figure 2.14, it can be observed that the 4thorder polynomial obtained for the
determination of L e .J .. f / L of a column in non-sway framework is almost identical to theoriginal data that is shown in Figure 2.12. It can be also deduced from Figure 2.15 thatthat the 4th order polynomial obtained for the determination of L e . J .. f / L of a column insway framework is not in a good agreement with the original data shown in Figure 2.13.
2.8.2.2 Genetic programming (GP)This section describes the analytical description of Figures 23 and 24 of BS 5950.Toropov and Alvarez (1998) suggested the use ofGP methodology (Koza, 1992) for theselection of the structure of an analytical approximation expression. The expressions arecomposed of elements from a terminal set (design variables kl and k2), and afunctionalset (mathematical operators +, *, I, -, etc), which are known as nodes. The functionalset, as shown in Figure 2.16, can be subdivided into binary nodes, which take any twoarguments, and unary nodes, which take one argument e.g. square root.
Unary node
Terminal node
Figure 2.16. Typical tree structure representing ao + (al kl + a2k2)2
Modelling the expression evolves through the action of three basic geneticoperations: reproduction, crossover and mutation. In the reproduction stage, Np
-
8/8/2019 Design of Steel Frames - BS 5950
43/46
Design Procedure/or Steel Frame Structures according toBS 5950 68
expressions are randomly created and the fitness of each expression is calculated.
A strategy must be adopted to decide which expressions should die. This is achieved bykilling those expressions having a fitness below the average fitness. Then, thepopulation is filled with the surviving expressions according to fitness proportionateselection. New expressions are then created by applying crossover and mutation, whichprovide diversity of the population. Crossover (Figure 2.17) combines two trees(parents) to produce two children while mutation (Figure 2.18) protects the modelagainst premature convergence and improves the non-local properties of the search.
.. . -- . . . ., .. . .. .,,,\\\IIIIIIII
.rr:,IIII
IIIIIII\\\,,,.. .
Parent 1 Parent 2
. . . . -- . . . ."IIIIIIIIII\\,,,
'"---,,, ,"
Child 1 Child 2
Figure 2.17. Crossover
-
8/8/2019 Design of Steel Frames - BS 5950
44/46
Design Procedure/or Steel Frame Structures according toBS 5950 69
{ . . . ,1+\\ I,. . .
Figure 2.18. Mutation
The GP methodology has been applied where the 4th order polynomialLeff_ _ _ _ ! _ =0.51496 + 0.1129124 k l + 0.1129124 k2 + 0.185809 k2 +L 1
0.185809 ki - 0.0005816 klk2 + 0.015352 k12k2+ 0.015352 k1ki -0.1343541 ki - 0.1343541 k~ + 0.032573 k1 4 + 0.032573 ki +0.053263 kik2 +0.053263 k1ki -0.03272728 k12ki (2.49)
is obtained for the determination of the effective length factor of a column in non-swayframework. For a column in sway framework, the 7th order polynomialLeff_ _ _ _ ! _ = 0.982287 + 0.843802 kl + 0.843802 k2 - 4.70571 k2 - 4.70571 ki -L 1
9.269518 klk2 + 45.2545 k12k2+ 45.2545 k1ki + 19.12882 ki +19.12882 ki - 39.380878 k14 - 39.380878 ki -103.84266 ki k2 -103.84266 k1ki -140.678021 k12ki + 47.49748 k~ + 47.49748 ki +124.82327 k1ki +124.82327 k{k2 +202.337 k~ki +202.337 k~ki-31.31407 k1 6 -31.31407 k; -75.925149 k1ki -75.925149 k15k2-141.37368 k14ki -141.37368 k12ki -164.73689 kik~ + 8.97372 k1 7 +8.97372 k; + 18.5579 k16k2+ 18.5579 klk; + 39.4783 k~ki +39.4783 k12ki +49.9215 k14ki +49.9215 kiki (2.50)
is achieved. This expression is depicted in Figure 2.19.
-
8/8/2019 Design of Steel Frames - BS 5950
45/46
Design Procedure/or Steel Frame Structures according toBS 5950 70
5.0
4.0
I J f 3.0L2.0
1.0
0.2 0.0 0.2kl k2(a) Surface plot
Pinned 1.00.9
0.8t 0.70.6k2 0.5
0.40.3
0.20.1
Fixed 0.00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0Fixed Pinned
(b) Contour plotFigure 2. 19. Graphical representation ofih order polynomial of L1 /L for
a column in a rigid-jointed non-sway frame
-
8/8/2019 Design of Steel Frames - BS 5950
46/46
Design Procedure/or Steel Frame Structures according toBS 5950 71
2.9 Concluding remarksThis chapter reviewed an overall background to the concept of the limit state design forsteel framework members to BS 5950. A brief introduction to the applied loads and loadcombination is presented. The serviceability, strength as well as sway stability criteriaemployed in the present context are summarised. Furthermore, a general layout of thedeveloped computer-based technique to framework design is presented. Finally,analytical polynomials are achieved to automate the determination of the effectivelength factor. Inthis investigation, the following observations can be summarised. For columns in a non-sway framework, the 2nd or 3rd or 4th order polynomials
presented in Table 2.8 can be successfully used to determine the effective lengthfactor in design optimization based techniques.
For columns in a sway framework, the 7th order polynomial can be applied whenboth of the column restraint coefficients are less than 0.95. Otherwise, the techniquediscussed in Section 2.8.1 maybe utilised.This chapter now will be followed by theory and methods of computing the
critical buckling load employed for more accurate evaluation of the effective bucklinglength.