![Page 1: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/1.jpg)
Corken Compressor Repair
![Page 3: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/3.jpg)
Inspection plate with model and serial #s
Crankcase breather vent
Oil filter and oil pump assembly
Gauge Openings
IOM Manual
![Page 4: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/4.jpg)
Oil Pressure Gauge, set 20-25 PSI
Oil filter on newer models, replace with oil changes.
Change oil every 2200 hours or 6 months which ever
occurs first. High duty cycle compressor should be
changed more frequently.
Oil pressure adjusting screw
In = increases pressure
Out = decreases pressure
Oil dipstick location
If the dip stick blows out of inspection
plate the crankcase vent is plugged.
Crankcase breather location. If excess
leakage is noted here, tighten packing nut
IOM Manual
![Page 5: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/5.jpg)
Remove serial number nameplate. The model
and serial number should be noted for
purchasing parts.
If packing leakage is noted use the wrench
supplied, tighten adjusting nuts ¼ turn and
operate the compressor to confirm an
acceptable leakage rate
IOM Manual
![Page 6: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/6.jpg)
Prior to repairs or inspection assure unit has
been depressurized. Loosen valve cap.
Remove valve cap and gasket
IOM Manual
![Page 7: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/7.jpg)
Loosen or remove holddown screws. Failure to do
this can cause cover plate breakage during assembly.
Remove cover plates. Note that model 291
compressors do not utilize cover plates.
IOM Manual
![Page 8: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/8.jpg)
Liquid relief (spec 3) suction valve, cage and
spacer.
Note: Valve gasket still in head
Discharge valve, cage and spacer.
Note: Valve gasket still in head
IOM Manual
![Page 9: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/9.jpg)
291 “Liquid Relief” Suction Valve
Assembly (Non-Adjustable)
691 “Liquid Relief” Suction Valve
Assembly (Non-Adjustable)
491 “Liquid Relief” Suction Valve
Assembly (Adjustable)
IOM Manual
![Page 10: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/10.jpg)
Ball seat area damage indicates the compressor has
operated with liquid inside or extremely high
differential pressures.
491 Liquid relief suction valves should be adjusted to relieve at around 200-225PSI differential. This setting
can typically be obtained by adjusting the screw down to about 1/8 inch, or one turn from the bottom. It is
better to be too high than too low. A low setting can cause excess heat as the warm gas is relieved back to
suction causing the temperature to increase. 291 and 691 liquid relief suction valves are preset and non-
adjustable.
IOM Manual
![Page 11: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/11.jpg)
Remove top center and lower head bolts. Head
bolts should be tightened in proper sequence.
Consult instruction manual for details.
Note that some older model 490 and 690
compressors may have gaskets between the
cylinder and the head. The surfaces should be
cleaned prior to assembly.
IOM Manual
![Page 12: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/12.jpg)
Piston clearance can be confirmed using a
straight edge and a thickness or “feeler”
gauge. The piston clearances are listed on
the piston page of the parts manuals.
It may also be confirmed by utilizing a depth gauge.
IOM Manual
![Page 13: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/13.jpg)
Using an allen (hex) wrench loosen all piston
screws. During assembly a removable type of
Locktite may be used if desired.
By holding inward on two opposite screws the
piston assembly can easily be removed.
IOM Manual
![Page 14: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/14.jpg)
Piston Assembly
A piston assembly includes rings, expanders, piston, platform and all small parts for the piston.
IOM Manual
![Page 15: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/15.jpg)
Remove the lower cylinder bolts to allow the
cylinder to be removed.
Remove the cylinder noting O-ring locations
and sealing areas. These areas should be
cleaned prior to reassembly.
IOM Manual
![Page 16: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/16.jpg)
Using side cutters, remove the roll pin. It
may be driven out if necessary, but it should
be squeezed or pressed in to avoid damage
to the new packing rings.
Remove the piston nuts
IOM Manual
![Page 17: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/17.jpg)
Shims are used to adjust piston clearance.
Typically the quantity removed should be
installed. Required clearances are shown on the
piston parts pages.
The thrust washer is thicker and
must always be installed first.
The piston nuts, roll pins and platforms
are typically reusable. A piston assembly
includes all piston parts.
IOM Manual
![Page 18: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/18.jpg)
The special wrench supplied with the
compressor should be used to remove the
packing box holddown screws.
On newer models the packing box has an O-ring seal
on the bottom. Older models the packing box does
not use a holddown screw. It can immediately
removed and has a gasket that seals the oil from the
crankcase, but not gas pressure.
IOM Manual
![Page 19: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/19.jpg)
Remove the snap ring and disassemble the
packing box assembly. The inside of the packing
box should be smooth and polished. Do not “sand
blast” the ID as it can cause packing leakage.
The above shows the complete packing box contents.
The packing set includes the Teflon packing parts along
with the packing spring and washer.
IOM Manual
![Page 20: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/20.jpg)
Packing Sets
Packing sets include the “Male” , “Female”
and “V” packing rings along with the spring
and packing washer.
Standard LPG compressor packing sets include eight (8)
“V” rings in the 291 and 491 models, while the 691 only
has four (4) rings included. “D” and “T” models use five
(5) on the small units and four on the D/T691
compressors.
Eight (8) packing rings with
a “male” and “female” ring.
IOM Manual
![Page 21: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/21.jpg)
Packing Styles
Standard LPG
Packing
“D” Style Packing
“T” Style Packing
Industrial Compressor IOM Manual
![Page 22: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/22.jpg)
D891 Packing
Upper “Segmented” packing.
Lower “V” ring packing
Packing vent and drain
D891 IOM Manual
![Page 23: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/23.jpg)
Packing installation cones may be used during assembly to avoid possible damage to the packing.
This tool is more helpful on the smaller model compressors, but is critical on the D891 for packing installation.
IOM Manual
![Page 24: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/24.jpg)
Remove crosshead guide to crankcase bolts.
These bolts should be tightened in proper
sequence during reassembly. See IOM manual
for information on torques and sequence.
Crosshead guide can be carefully removed and
inspected for scores or wear.
IOM Manual
![Page 25: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/25.jpg)
Remove crankcase inspection plate to allow
access to the connecting rods and crankshaft. The inspection plate is sealed with a gasket.
IOM Manual
![Page 26: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/26.jpg)
Rotate the crankshaft to access the connecting
rod nuts.
Remove the nuts and remember the nuts must
be to a proper torque during reassembly.
IOM Manual
![Page 27: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/27.jpg)
A piece of wood will assist in removing the
connecting rod from the crankshaft. By rotating
the crankshaft it creates even pull on the rod
cap.
The connecting rod bearings can now be inspected
for wear or lubrication problems. If the bearings are
worn the crankshaft should be inspected for damage.
IOM Manual
![Page 28: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/28.jpg)
It is critical that the locking tabs are aligned during assembly. The bearing has a tab
and the rod has notches, these must be aligned.
IOM Manual
![Page 29: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/29.jpg)
The connecting rod cap must align
to the rod. Most have arrows or
notches for assistance.
IOM Manual
![Page 30: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/30.jpg)
The crosshead assembly is only sold as a complete assembly to assure alignment. The
con-rod assembly includes rod bearings, bushing and nuts. The wrist pin and retainers
are sold separately.
Con-rod Assembly
Wrist pin and retainers
Crosshead Assembly
IOM Manual
![Page 31: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/31.jpg)
The wrist pin should be pressed in starting with the
“tapered” end. Care should be taken to assure that
the con-rod stays loose during the installation of
the wrist pin.
The wrist pin may be pressed out after
removing the wrist pin retainer rings
IOM Manual
![Page 32: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/32.jpg)
Each cap must stay with the rod and
alignment of notches and arrows is critical.
The rod nuts must torque to specification. See
service manual pages for specifications.
If bushings are changed they must be machined to
dimension and assure oil passage alignment.
IOM Manual
![Page 33: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/33.jpg)
Con-rod bearings severely damaged are typically caused by a lubrication
breakdown or a total lack of oil/oil pressure. Oil should be changed frequently
even if it “looks” good.
IOM Manual
![Page 34: Corken Compressor · PDF fileRemove serial number nameplate. The model and serial number should be noted for purchasing parts. If packing leakage is noted use the wrenchContact ·](https://reader034.vdocuments.us/reader034/viewer/2022050713/5ab0c6a37f8b9a00728b75af/html5/thumbnails/34.jpg)
Thank you for your attention!
Corken Inc.
3805 N.W. 36th St.
Oklahoma City OK. 73112 U.S.A.
Phone (405) 946-5576 FAX (405) 948-7343
www.corken.com [email protected]