ClearCreek Siding
Part Catalog
Www.ClearCreekSiding.com417-862-9511
Version 7.0
LogNo
Chinking
All dimensions are approximate and may vary.
Timberwith
Chinking
Siding is produced in 12’ lengths and each end has a concretefactory edge. For runs shorter than 12’, siding can be cut downat the to the length needed.jobsite
Siding Styles
7-1/2” 8-1/4”
11-1/4” 11-1/4”
2-3/4”2-3/4”
2-3/4” 2-3/4”
TimberNo
Chinking
Logwith
Chinking
Version 7.0
Small Window Sill/Head Trim
3.75"
3.75"
Trim Options
This Trim is used as Window Head/Sill trim and Door Head trim.
They are made custom length in the factory and finished on each end.
Typically the Small trim is used with the Log Style and the Large trim is used with theTimber style. However, they are interchangeable.
Parts may be provided in 12’ pieces, cut in the field and the ends finished.Optional:
Large Window Sill/Head Trim
5.5"
0.50"
3.75"
5.0"
Standard Termination Trim
2 7/8"
3 3/8"
Termination Trims
5.25"
3.375"
This Trim is used as vertical casings for Windows and Doors and as a transition trim incases where siding is terminating into something other than a corner or casing.
Small Termination trim can also be used at soffits and gables.
This part is produced in 12’ lengths and to the length needed.
Optional:
will be cut at the jobsite
Large Termination Trim
Window/Door Trim
All dimensions are approximate and may vary. Version 7.0
3.625"
Inside Corner
Round Outside Corner
Outside Corner, 135 Degree
4.5”
This part is used at 90 degree insidecorners.
It is produced in 10’ lengths andto the length needed.
The bottom end of the part is finished.
will becut at the jobsite
This part is used at 90 degree outsidecorners.
Included is a “Wood Corner Base.”
It is produced in 10’ lengths andto the length needed.
The bottom end of the part is finished.
will becut at the jobsite
This part is used at 135 degree outsidecorners, often found on bay windows.
It is produced in 10’ lengths andto the length needed.
The bottom end of the part is finished.
will becut at the jobsite
Corner Trims
All dimensions are approximate and may vary.
Square Outside Corner
This part is used at 90 degree outsidecorners.
It is produced in 10’ lengths andto the length needed.
The bottom end of the part is finished.
will becut at the jobsite
3.00”
3.625”
0.5”3.625” 3.00”
7.125”
7.125”
4.5”
4.5”
Version 7.0
Custom Trim
Version 7.0
Window
Window Window
Custom Trim forarched windows
Custom Bands for between windows
Custom Sillsfor betweenwindows
ClearCreek can also provide Custom Trim: Arches, Trimbetween windows too narrow for Standard Trim, etc.
Electrical OutletBlock, Single
Faucet MountingBlock
Accessories
6.5"
6.5"
Light Block
6.5"
6.5"
Dryer VentBlock
4.0”
All dimensions are approximate and may vary.
Accessories are 3” deep
Low ProfileFaucet Mounting Block
6.5"
6.5"
10.5"
6.5"
2.0"
6.0"2.0"
4.25"
3"
4.7
5”
5.25”
9.2
5”
1.125"
1.125"
Version 7.0
Custom Accessory Blocks are also available.
2 1/2” #8 Bugle HeadCoated Exterior Screw
5” #10 Bugle HeadCoated Exterior Screw
Fasteners
Metal Starter Clip3/4” Plastic Washer
Version 7.0
Silicone Sealant
Concrete Fill Mix
Coatings
FoamCoat 550
Concrete Sealer
Version 7.0
