FunctionThe CDP 40T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.
Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
POOL DEHUMIDIFIERS CDP
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
CDP 40T SWIMMING POOL DEHUMIDIFIER
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
Model CDP 40TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 400 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 3,8 AMax. power consumption 0,9 kWRefrigerant R407CQuantity of refrigerant 0,7 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 43 dB(A)Weight 57,5 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
INSTALLATION
POOL DEHUMIDIFIERS CDP
CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5
Temp. oC
L/H
CDP 40T
40% RH 60% RH 80% RH
Specific energy consumption (SEC): 0,47 kWh/l at 28°C & 60% RH
POOL DEHUMIDIFIERS CDP
DIMENSIONS CDP 40T
AccessoriesWireless remote control DRC1 Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter
dantherm.com
All dimensions are in mm.
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6
998 294
304
700
Drain outlet position
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6 430,7
50,6
The duct kit includes an extension for wall thickness from 70 to 366 mm.
A B C Wall opening
CDP 40T 465 998 642 610 x 110
Duct kits CDP 40T
c 80
146
106
235 73
FunctionThe CDP 50T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.
Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
POOL DEHUMIDIFIERS CDP
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
CDP 50T SWIMMING POOL DEHUMIDIFIER
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
Model CDP 50TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 680 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 6,6 AMax. power consumption 1,5 kWRefrigerant R407CQuantity of refrigerant 0,9 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 44 dB(A)Weight 66 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
CAPACITY CURVES
INSTALLATION
POOL DEHUMIDIFIERS CDP
CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0
Temp.
L/H
60% RH 80% RH
CDP 50T
40% RH
Specific energy consumption (SEC): 0,48 kWh/l at 28°C & 60% RH
°C
POOL DEHUMIDIFIERS CDP
DIMENSIONS CDP 50T
AccessoriesWireless remote control DRC1Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter
dantherm.com
All dimensions are in mm.
Duct kits CDP 50T
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6
1148 294
304
700
Drain outlet position
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6 430,7
50,6
The duct kit includes an extension for wall thickness from 70 to 366 mm.
A B C Wall opening
CDP 50T 616 1148 791 760 x 110
c 80
146
106
235 73
FunctionThe CDP 70T is an energy efficient and quiet pool dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led from the drip tray to a drain. The cold, dry air is then passed over the condenser coil where it is re-heated, before leaving the unit at a tempera-ture, which is approx. 5°C higher than at the inlet.
Applications:• Indoor swimming pools, private or hotels• Therapy pools• Spas• Gymnasias
POOL DEHUMIDIFIERS CDP
DiodesBLUE: Power connected, standby modeGREEN: Compressor ON, deicingYELLOW: Remote pairing modeRED: Errors
DefrostingActive, demand-controlled defrosting is incorporated into the electronic control.
ServiceFor easy service the refrigerant circuit is supplied with a service valve. The PCB has a USB gate for history data logging for easy fault finding.
CDP 70T SWIMMING POOL DEHUMIDIFIER
FEATURES
Dehumidifier• Built into a strong and robust powder coated hot galvanized sheet metal
cabinet• Evaporator and condenser coils are epoxy-coated for high corrosion
resistance• Fixed to the wall by means of a wall mounting strip supplied with the unit• Condensate outlet located at the bottom. Outlet stub can be connected
to a ¾” hose• Outside connection to mains
Control• Built in electronic hygrostat and thermostat• To establish ideal ambient sensor point (RH/t) the fan(s) run 1 minute each hour• Integrated ON/OFF control of humidity and temperature (electric or water
heating coils as accessories)• 0-VOLT connection for alarm• 230 V for control valve, exhaust fan and pump/boiler• RS 485 gate for BMS (Modbus)
Model CDP 70TOperating range – humidity 40 – 100% RHOperating range – temperature 10 – 36 °CAir volume 900 m3/hPower supply 1x230/50 V/HzMax. ampere consumption 8 AMax. power consumption 1,8 kWRefrigerant R407CQuantity of refrigerant 1,2 kgCompressor RotaryFan RadialSound level (in pool room 1 m from the wall) 47 dB(A)Weight 77,5 kgFilter G3 PPI 15Colour (Cabinet) RAL 7035Protection class IPX4 Corrosion protection in accordance with EN/ISO 12944-2 C4
dantherm.com
TECHNICAL DATA
INSTALLATION
POOL DEHUMIDIFIERS CDP
0
5
10
15
20
25
30
35
40
0 1 2 3 4 5 6
Temp.
L/H
CDP 70T
40% RH 60% RH 80% RH
Specific energy consumption (SEC): 0,43 kWh/l at 28°C & 60% RH
CAPACITY CURVES
CDP 40T, 50T and 70T are designed for installation in an adjacent room and are supplied with a through-the-wall duct kit with supply and return air grills (accessory).
°C
POOL DEHUMIDIFIERS CDP
dantherm.com
All dimensions are in mm.
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6
1483 294
304
700
Drain outlet position
351 518
Surface appearance according to reference
CDP 70 T
1006419.82g
13-09-2016
"Thickness@@part1.SLDPRT"mm
351518
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
REV.:
bof
Sheetmetal flatstate is based on Dantherm Air Handling A/S
All designs originated by Dantherm Air Handling A/S are the
table LZT 142 0001, category
PART NOproperty of said Company and will be protected by Patents.
8
SCALE: NOT TO SCALE
REV.:CDP 70 T
PAR
TN
O
process equipment and is only entended as a guide.
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 70 T 1483
CDP 50 T 1148
CDP 40 T 998
700
294
304
430,7
50,
6 430,7
50,6
DIMENSIONS CDP 70T
AccessoriesWireless remote control DRC1Water heating coils Control valve for water heating coilsElectric heating coilsExhaust fansThrough-wall duct kit with filter, extension kit and alu grillDuct lead-in adapter
The duct kit includes an extension for wall thickness from 70 to 366 mm.
A B C Wall opening
CDP 70T 950 1483 1126 1095 x 110
Duct kits CDP 70T
c 80
146
106
235 73