Download - Cabling lans and wans
![Page 1: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/1.jpg)
Cabling LANs and WANs
![Page 2: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/2.jpg)
Copper CablesTwisted-pair—Twisted-pair cables are
composed of one or more pairs of copper wires.
Coaxial—Coaxial cable has one center conductor of either solid or stranded copper wire.
![Page 3: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/3.jpg)
Twisted-Pair Cable
The wire pairs are twisted for two reasons.First, cancellation.Second, filter out noise because the noise
signals cancel each other.Twisted
Pair
shielded
STP FTP
Unshielded
UTP
![Page 4: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/4.jpg)
Shielded Twisted-Pair Cable STP
STP
![Page 5: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/5.jpg)
Screened twisted-pair (ScTP) or foil twisted-pair (FTP)
FTP
![Page 6: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/6.jpg)
Unshielded Twisted-Pair Cable UTPThe connector used on a UTP cable is called
a registered jack 45 (RJ-45) connector
UTP
![Page 7: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/7.jpg)
Category 1 (CAT 1)—Used for telephone communications. Not suitable for transmitting data.
Category 2 (CAT 2)—Capable of transmitting data at speeds up to 4 Mbps.
Category 3 (CAT 3)—Used in 10BASET Ethernet networks. Can transmit data at speeds up to 10 Mbps.
Category 4 (CAT 4)—Used in Token Ring networks. Can transmit data at speeds up to 16 Mbps.
Category 5 (CAT 5)—Can transmit data at speeds up to 100 Mbps. Used in Fast Ethernet networks.
Category 5e (CAT 5e)—Used in networks running at speeds up to 1000 Mbps (1 Gbps). Used in Gigabit Ethernet (GigE) networks.
Category 6 (CAT 6)—The specification for CAT 6 is new, was released on February 3, 2003, and is currently available for installation and use. Used in Gigabit Ethernet (GigE) networks.
![Page 8: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/8.jpg)
Coaxial Cable
![Page 9: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/9.jpg)
Cabling LANs
The primary advantage and disadvantage comparison categories are as follows:
Cable lengthCostEase of installation
![Page 10: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/10.jpg)
Ethernet in the Campus
![Page 11: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/11.jpg)
UTP ImplementationA straight-through cable—A cable that
maintains the pin connection all the way through the cable. Thus, the wire connected to pin 1 is the same on both ends of the cable.
A crossover cable—A cable that crosses the critical pair to properly align, transmit, and receive signals on the device with line connections.
![Page 12: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/12.jpg)
wires 1, 2, 3, and 6 are used for transmit (TD) and receive (RD) signals
Straight Through Cabling
![Page 13: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/13.jpg)
EIA/TIA-568-A and EIA/TIA-568-B standards
![Page 14: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/14.jpg)
Crossover Cablepin 1 at one RJ-45 end should connect to pin
3 at the other end. Pin 2 at one end should connect to pin 6 at the other end.
![Page 15: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/15.jpg)
EIA/TIA-568-A and EIA/TIA-568-B standards
![Page 16: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/16.jpg)
Use straight-through cables for the following cabling:Switch to routerSwitch to PC or serverHub to PC or server
Use crossover cables for the following cabling:Switch to switchSwitch to hubHub to hubRouter to routerPC to PCRouter to PC
![Page 17: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/17.jpg)
Cabling the WAN
Serial connectionsDSL (digital subscriber line )Cable modem
RJ-11 connector
![Page 18: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/18.jpg)
Setting Up Console ConnectionsThe cable used between a terminal and a
console port is a rollover cable with RJ-45 connectors.
![Page 19: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/19.jpg)
Step 1: Cable the devices using a rollover cable. You likely need an RJ-45-to-DB-9 or an RJ-45-to-DB-25 adapter for your PC or terminal.
Step 2: Configure your terminal emulation application with the following common equipment (COM) port settings:9600 bps8 data bitsNo parity1 stop bitNo flow control.
![Page 20: Cabling lans and wans](https://reader036.vdocuments.us/reader036/viewer/2022081515/587e7e611a28abd6038b5ae1/html5/thumbnails/20.jpg)
THANKS !