Download - AVR-4311CI_4311 (v.1) (sm)
-
D&M Holdings Inc.
SERVICE MANUAL
e
e
Copyright 2010 D&M Holdings Inc. All rights reserved.WARNING: Violators will be prosecuted to the maximum extent possible.
MODEL JP EU EC E2 EK E2A E1C EUT
AVR-4311CI 3 3AVR-4311 3 3
AV SURROUND RECEIVER
Ver. 1
Some illustrations using in this service manual are slightly different from the actual set.
Please use this service manual with referring to the operating instructions without fail.
For purposes of improvement, specifi cations and design are subject to change without notice.
S0106-1V01DM/DG1009
-
2SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.Be sure to test for leakage current with the AC plug in both polarities, in addition, in each power ON, OFF and STANDBY mode, if applicable.
CAUTION Please heed the points listed below during servicing and inspection. Heed the cautions!
Spots requiring particular attention when servicing, such as the cabinet, parts, chassis,etc., have cautions indicated on labels. be sure to heed these causions and the cautions indicated in the handling instructions.
Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching
internal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc.
(2) Tere are high voltage parts inside. Handle with extra care when the set is energized.
Caution concerning disassembly and assembly!
Through great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fi ngers are moved across them. Use gloves to protect your hands.
Only use designated parts!The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same poroperties. In particular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the designated parts.
Be sure to mount parts and arrange the wires as they were originally!
For safety seasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wores omsode amd clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally.
Inspect for safety after servicing!Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an inslation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured.
(Insulation check procedure)Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired.
Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be poreserved. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number.
(1) Schematic diagrams ...... Indicated by the z mark.(2) Parts lists ...... Indicated by the z mark.
Using parts other than the designated parts could result in electric shock, fi res or other dangerous situations.
CAUTION Concerning important safety parts
-
3NOTE FOR SCHEMATIC DIAGRAMWARNING:Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.CAUTION:Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.WARNING:DO NOT return the unit to the customer until the problem is located and corrected.NOTICE:ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHMALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
Parts for which "nsp" is indicated on this table cannot be supplied.When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.Ordering part without stating its part number can not be supplied.
Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Part indicated with the mark "" is not illustrated in the exploded view.
WARNING:
1.2.3.4.5.6.
Resistors
RD : CarbonRC : CompositionRS : Metal oxide filmRW: windingRN : Metal filmRK : Metal mixture
P : Pulse-resistant typeNL : Low noise typeNB : Non-burning typeFR : Fuse-resistorF : Lead wire forming
2B : 1/8 W2E : 1/4 W2H : 1/2 W3A : 1 W3D : 2 W3F : 3 W3H : 5 W
F : 1%G : 2%J : 5%K : 10%M : 20%
Ex.: RN
Type
14K
Shapeand per-formance
2E
Power
182
Resist-ance
G
Allowableerror
FR
Others
* Resistance1800ohm=1.8kohm1 8 2
Indicates number of zeros after effective number.2-digit effective number.
1.2ohm1 R 2
2-digit effective number, decimal point indicated by R.1-digit effective number.
: Units: ohm
Capacitors
CE : Aluminum foilelectrolytic
CA : Aluminium solidelectrolytic
CS : Tantalum electrolyticCQ: FilmCK : CeramicCC : CeramicCP : OilCM: MicaCF : MetallizedCH : Metallized
HS : High stability typeBP : Non-polar typeHR : Ripple-resistant typeDL : For change and dischargeHF : For assuring high requencyU : UL partC : CSA partW : UL-CSA partF : Lead wire forming
0J : 6.3 V1A : 10 V1C : 16 V1E : 25 V1V : 35 V1H : 50 V2A : 100 V2B : 125 V2C : 160 V2D : 200 V2E : 250 V2H : 500 V2J : 630 V
F : 1%G : 2%J : 5%K : 10%M : 20%Z : 80%
: - 20%P : +100%C : 0.25pFD : 0.5pF= : Others
Ex.: CE
Type
04W
Shapeand per-formance
1H
Dielectricstrength
3R2
Capacity
M
Allowableerror
BP
Others
Units:F.
2200F2 2 2
Indicates number of zeros after effective number.2-digit effective number.
Units:F.
2.2F2 R 2
2-digit effective number, decimal point indicated by R1-digit effective number.
* Capacity (electrolyte only)
When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
* Capacity (except electrolyte)
Units:pF
2200pF=0.0022F2 2 2
Indicates number of zeros after efective number. (More than 2)2-digit effective number.
Units:pF
220pF2 2 1
2-digit effective number.Indicates number of zeros after effective numver. (0 or 1)
NOTE FOR PARTS LIST
-
4TECHNICAL SPECIFICATIONS n Audio Section Power amplifi er
Rated output :Front : 140 W + 140 W (8 , 20 Hz 20 kHz with 0.05 % T.H.D.) 170 W + 170 W (6 , 1 kHz with 0.7 % T.H.D.)Center : 140 W (8 , 20 Hz 20 kHz with 0.05 % T.H.D.) 170 W (6 , 1 kHz with 0.7 % T.H.D.)Surround : 140 W + 140 W (8 , 20 Hz 20 kHz with 0.05 % T.H.D.) 170 W + 170 W (6 , 1 kHz with 0.7 % T.H.D.)Surround back / Front height / Front wide : 140 W + 140 W (8 , 20 Hz 20 kHz with 0.05 % T.H.D.) 170 W + 170 W (6 , 1 kHz with 0.7 % T.H.D.)
Dynamic power : 150 W x 2ch (8 220 W x 2ch (4 )Output connectors : 4 16
AnalogInput sensitivity/Input impedance : 200 mV/47 kFrequency response: 10 Hz 100 kHz +1, 3 dB (DIRECT mode)S/N: 102 dB (IHFA weighted, DIRECT mode)Distortion: 0.005 % (20 Hz ~ 20 kHz) (DIRECT mode)Rated output: 1.2 V
DigitalD/A output: Rated output 2 V (at 0 dB playback)Total harmonic distortion 0.008 % (1 kHz, at 0 dB)S/N ratio 102 dBDynamic range 100 dBDigital input: Format Digital audio interface
Phono equalizer (PHONO input REC OUT)Input sensitivity: 2.5 mVRIAA deviation: 1 dB (20 Hz to 20 kHz)S/N: 74 dB (A weighting, with 5 mV input)Rated output: 150 mVDistortion factor: 0.03 % (1 kHz, 3 V)
n Video Section Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Frequency response : 5 Hz 10 MHz +0, 3 dB
(when Video Convert set to OFF) Color component video connector
Input/output level and impedance : Y (brightness) signal 1 Vp-p, 75 PB / CB signal 0.7 Vp-p, 75 PR / CR signal 0.7 Vp-p, 75 Frequency response : 5 Hz 60 MHz +0, 3 dB
(when Video Convert set to OFF)
n HD Radio section (for EU,EC)[FM](Note: V at 75 , 0 dBf = 1 x 1015 W)
Receiving Range :
[FM] 87.5 MHz 107.9 MHz [AM]530 kHz 1710 kHzUsable Sensitivity :
[FM]1.5 V (14.8 dBf) [AM]20 VS/N (IHF-A) :
[FM]MONO 78 dB [AM]STEREO 68 dBHD 85 dB 85 dB
Total harmonic Distortion (at 1 kHz) :
[FM]MONO 0.1 % [AM]STEREO 0.2 %HD 0.02 % 0.02 %
n Tuner section (for E2, E1C)[FM](Note: V at 75 , 0 dBf = 1 x 1015 W)
Receiving Range :
[FM] 87.5 MHz 108.0 MHz [AM]522 kHz 1611 kHzUsable Sensitivity :
[FM]1.2 V (12.8 dBf) [AM]18 V50 dB Quieting Sensitivity :[FM]MONO 2.0 V (17.3 dBf)
STEREO 42 V (34.5 dBf)S/N (IHF-A) :[FM]MONO 72 dB
STEREO 67 dBTotal harmonic Distortion (at 1 kHz) :[FM]MONO 0.3 %
STEREO 0.7 % n General
Power supply : AC 120 V, 60 Hz (for EU,EC) AC 230 V, 50 Hz (for E2) AC 220 V, 50 Hz (for E1C)Power consumption :780 W0.1 W (Standby)2.2 W (CEC standby)Maximum external dimensions :434 (W) x 171 (H) x 414 (D) mm (17-3/32 x 6-47/64 x 16-19/64)Weight : 17.3 kg
n Remote Control Unit (RC-1145)Batteries : R6/AA Type (two batteries)Maximum external dimensions :53 (W) x 224 (H) x 30 (D) mm (2-3/32 x 8-13/16 x 1-3/16)Weight : 178 g (6.3 oz, including batteries)
n Remote Control Unit (RC-1148)Batteries : R03/AAA Type (two batteries)Maximum external dimensions : 49 (W) x 220 (H) x 24.5 (D) mm (1-59/64 x 8-21/32 x 31/32)Maximum external dimensions : 114 g (Approx 4 oz, including batteries)
-
5244.5
372.8
54.7
20.5
414
20.7
434
344
170.5
15.5
155
9029.5 35.5
163
44.2
133
DIMENSION
-
6CAUTION IN SERVICINGBefore the Digital P.W.B. are replaced
If you cannot specify the cause of the digital PWB defect, carry out "Initializing" "Update to latest fi rmware".The defect may be cleared. See the following for the method of initializing the com.
Initializing AV SURROUND RECEIVERAV SURROUND RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced.
1. Turn off the power using ON/STANDBY button.2. Press ON/STANDBY button while simultaneously pressing STANDARD and DSP SIMULATION buttons.3. Check that the entire display is fl ashing with an interval of about 1 second, and release your fi ngers from the 2
buttons and the microprocessor will be initialized.
Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Offi cial Service Distributor in your region if necessary.
8U-110084S : EXTENSION UNIT KIT : 1 Set(Refer to "JIG FOR SERVICING".)
Note: If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode.
So make sure to memorize your setting for restoring after the initialization.
2,31,2
-
7DISASSEMBLY Disassemble in order of the arrow of the fi gure of following fl ow. In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. In the case of the re-assembling, observe "attention of assembling" it. If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly
as they were originally bundled or placed afterward.Otherwise, incorrect arrangement can be a cause of noise generation.
TOP COVER
FRONT PANEL SUB ASSYRefer to "DISASSEMBLY
1. FRONT PANEL SUB ASSY"and "EXPLODED VIEW"
FRONT UNIT(Ref. No. of EXPLODED VIEW : A-1)
MIC UNIT(Ref. No. of EXPLODED VIEW : A-2)
FUNCTION UNIT(Ref. No. of EXPLODED VIEW : A-3)
USB UNIT(Ref. No. of EXPLODED VIEW : A-4)
FUNCTION CNT UNIT(Ref. No. of EXPLODED VIEW : A-5)
V.AUX UNIT(Ref. No. of EXPLODED VIEW : A-6)
FRONT HOLD UNIT(Ref. No. of EXPLODED VIEW : B-10)
SMPS UNITRefer to "DISASSEMBLY
6. SMPS UNIT"and "EXPLODED VIEW"
FAN DRIVE UNIT(Ref. No. of EXPLODED VIEW : G-7)
SMPS UNIT(Ref. No. of EXPLODED VIEW : H-3)
D103 UNIT(Ref. No. of EXPLODED VIEW : H-4)
RADIATOR(L) SUB ASSYRefer to "DISASSEMBLY
2. RADIATOR(L) SUB ASSY"and "EXPLODED VIEW"
P.AMP UNIT(L1)(Ref. No. of EXPLODED VIEW : C-1)
P.AMP UNIT(L2)(Ref. No. of EXPLODED VIEW : C-2)
P.AMP UNIT(L3)(Ref. No. of EXPLODED VIEW : C-3)
P.AMP UNIT(L4)(Ref. No. of EXPLODED VIEW : C-4)
AMP CONNECT UNIT( L )(Ref. No. of EXPLODED VIEW : C-7)
POSISTOR UNIT(L)(Ref. No. of EXPLODED VIEW : C-12)
POSISTOR CONNECT UNIT(L)(Ref. No. of EXPLODED VIEW : C-14)
RADIATOR(R) SUB ASSYRefer to "DISASSEMBLY
4. RADIATOR(R) SUB ASSY"and "EXPLODED VIEW"
P.AMP UNIT(R2)(Ref. No. of EXPLODED VIEW : B-2)
P.AMP UNIT(R3)(Ref. No. of EXPLODED VIEW : B-3)
P.AMP UNIT(R4)(Ref. No. of EXPLODED VIEW : B-4)
P.AMP UNIT(R5)(Ref. No. of EXPLODED VIEW : B-5)
P.AMP UNIT(R6)(Ref. No. of EXPLODED VIEW : B-6)
AMP CONNECT UNIT( R )(Ref. No. of EXPLODED VIEW : B-7)
FFC HOLD UNIT(Ref. No. of EXPLODED VIEW : B-9)
POSISTOR UNIT(R)(Ref. No. of EXPLODED VIEW : B-13)
POSISTOR CONNECT UNIT(R)(Ref. No. of EXPLODED VIEW : B-15)
FFC HOLD UNIT(Ref. No. of EXPLODED VIEW : I-11)
BACK PANEL SUB ASSYRefer to "DISASSEMBLY
5. BACK PANEL SUB ASSY"and "EXPLODED VIEW"
DIODE JOINT UNIT(Ref. No. of EXPLODED VIEW : B-8)
RECTIFIER UNIT(Ref. No. of EXPLODED VIEW : B-11)
DIGITAL PWB ASSY(Ref. No. of EXPLODED VIEW : D)
A.VIDEO PWB ASSY(Ref. No. of EXPLODED VIEW : E)
INPUT UNIT(Ref. No. of EXPLODED VIEW : F-1)
PREOUT UNIT(Ref. No. of EXPLODED VIEW : F-2)
VOLUME UNIT(Ref. No. of EXPLODED VIEW : G-1)
SIRIUS UNIT(Ref. No. of EXPLODED VIEW : G-2)
232C/TRIG UNIT(Ref. No. of EXPLODED VIEW : G-3)
SPDIF UNIT(Ref. No. of EXPLODED VIEW : G-4)
FH/FW UNIT(Ref. No. of EXPLODED VIEW : G-5)
FRONT HDMI UNIT(Ref. No. of EXPLODED VIEW : G-6)
SPEAKER UNIT(Ref. No. of EXPLODED VIEW : H-1)
FUSE UNIT(Ref. No. of EXPLODED VIEW : H-2)
AC OUTLET UNIT(Ref. No. of EXPLODED VIEW : H-5)
FRONT CONNECT UNIT(Ref. No. of EXPLODED VIEW : I-1)
SIDE CONNECT-1 UNIT(Ref. No. of EXPLODED VIEW : I-2)
REG/VIDEO CONNECT UNIT(Ref. No. of EXPLODED VIEW : I-3)
PRE CONNECT-2 UNIT(Ref. No. of EXPLODED VIEW : I-4)
PRE CONNECT-1 UNIT(Ref. No. of EXPLODED VIEW : I-5)
INPUT JOINT-2 UNIT(Ref. No. of EXPLODED VIEW : I-6)
INPUT JOINT-1 UNIT(Ref. No. of EXPLODED VIEW : I-7)
SPDIF JOINT-1 UNIT(Ref. No. of EXPLODED VIEW : I-8)
SPDIF JOINT-2 UNIT(Ref. No. of EXPLODED VIEW : I-9)
SIDE CONNECT-2 UNIT(Ref. No. of EXPLODED VIEW : I-12)
MAIN TRANSRefer to "DISASSEMBLY
3. MAIN TRANS"and "EXPLODED VIEW"
MAIN TRANS(Ref. No. of EXPLODED VIEW : 38)
-
8About the photos used for descriptions in the DISASSEMBLY" section. The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***"
at the left of the respective photographs. Refer to the table below for a description of the direction in which the photos were taken. Photographs for which no direction is indicated were taken from above the product.
1. FRONT PANEL SUB ASSY
(1) Remove the screws.
The viewpoint of each photograph(Photografy direction)
View from above Front side
Direction of photograph: B
Direction of photograph: DDirection of photograph: C
Direction of photograph: A
TOP COVER FRONT PANEL SUB ASSYProceeding :
View from bottom
-
9(2) Disconnect the connector wires and FFC cable, then remove the screws.
Direction of photograph: BDirection of photograph: C
CN604
FFC cable
FFC cable
N5302
HOLDER : Loose
STYLEPIN : Loose
STYLEPIN : Loose
STYLEPIN : Loose
Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in FRONT PANEL SUB ASSY.
-
10
2. RADIATOR(L) SUB ASSY
(1) Disconnect the connector wires, then remove the screws.
(2) Cut wire clamp band, then disconnect the connector wires.
b When removing CONNECT PWB, remove the claw of the JL connector.
Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in RADIATOR(L) SUB ASSY.
TOP COVER FRONT PANEL SUB ASSY RADIATOR(L) SUB ASSYProceeding :
RADIATOR(L) SUB ASSY
N9020N9021
STYLEPIN : Loose
HOLDER : Loose
cut
9003N9022N9023
CONNECT UNITclaw
-
11
3. MAIN TRANS
(1) Cut wire clamp band, then remove the screws.
(2) Cut wire clamp band, then disconnect the connector wires.
TOP COVER FRONT PANEL SUB ASSY RADIATOR(L) SUB ASSYProceeding :
MAIN TRANS
Proceeding :
cut
Direction of photograph: DN4005
N4001N4003 N4002
cut
-
12
4. RADIATOR(R) SUB ASSY
(1) Disconnect the connector wires, then remove the screws.
(2) Cut wire clamp band, then disconnect the connector wires.
b When removing CONNECT PWB, remove the claw of the JL connector.
Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in RADIATOR(R) SUB ASSY.
TOP COVER FRONT PANEL SUB ASSYMAIN TRANS
RADIATOR(L) SUB ASSYRADIATOR(R) SUB ASSY
Proceeding :
RADIATOR(R) SUB ASSY
N9001N9002
cut
N901 N9022 N9025
CONNECT UNITclaw
-
13
5. BACK PANEL SUB ASSY
(1) Cut wire clamp band, then disconnect the connector wires. Remove the screws.
(2) Remove the screws and the HOLDER.
(3) Remove the screws.
TOP COVER FRONT PANEL SUB ASSYMAIN TRANS
RADIATOR(L) SUB ASSYRADIATOR(R) SUB ASSY BACK PANEL SUB ASSY
Proceeding :
BACK PANEL SUB ASSY
cutcut
N4004
N6001
N2008
View from bottomHOLDER
-
14
(4) Remove BACK PANEL SUB ASSY from the main unit.Cut wire clamp band, then remove the screws.
b When remove the SP SCREW COVER, HIMELON SHEET is attached to SCREW COVER.
Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in BACK PANEL SUB ASSY.
BACK PANEL SUB ASSY
Direction of photograph: DDirection of photograph: C
cut
cut
cut
SP SCREW COVER
HIMELON SHEET
-
15
6. SMPS UNITY
(1) Cut wire clamp band.
(2) Remove the screws.
(3) Remove the screws.
TOP COVER FRONT PANEL SUB ASSYMAIN TRANS
RADIATOR(L) SUB ASSYRADIATOR(R) SUB ASSY BACK PANEL SUB ASSY
SMPS UNIT
Proceeding :
cut
View from bottom
HOLDER
STYLEPIN : Loose
STYLEPIN : Loose
-
16
SPECIAL MODESpecial mode setting buttonb Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time.
Mode Button A Button B Contents
Version display(com/DSP Error Display) STATUS RETURN
Serial No. and fi rmware versions such as Main, Sub, DSP aredisplayed in the FL manager. Errors are displayed when theyoccur. (Refer to 17 page)
Displaying the protection history mode STATUS MENU Displaying the protection history(Refer to 20 page)
IInitialization mode(Remove settings for Installer Setup.) STANDARD
DSPSIMULATION
Backup data initialization is carried out.(Remove settings for Installer Setup)
Initialization mode(Includes settings for Installer Setup) CURSOR UP
CURSORDOWN
Backup data initialization is carried out.(Includes settings for Installer Setup)
Mode for switching tuner frequency step STANDARD PURE DIRECT---E2 model only---Change tuner frequency step to FM:200kHz/AM:10kHzSTEP
Mode for preventing remote controlacceptance STATUS ENTER
Operations using remote control are rejected.(Mode cancellation: Turn off power and execute the same button operations as when performing setup.)
Panel lock mode DSPSIMULATIONDIRECT/STEREO
Operations using main unit panel buttons or master volume arerejected.
Panel lock mode(Remove Master volume)
DIRECT/STEREO
PUREDIRECT Operations using main unit panel buttons are rejected.
Cancellation of panel lock mode DIRECT/STEREO ENTER Panel lock mode is cancelled.
Installer Setup mode MENU CURSORLEFT
Access Remote Maintenance mode via the internet.Installer Setup is displayed on GUI/Option Menu. Refer to AVR_RemoteMaintenance_.pdf of SDI.
NOTE:If " S " is displayed on the fl uorescent display, the unit is set to the special developer's mode and RS-232C communications are not possible.Press and hold in the "STATUS" and " i " buttons for over 3 seconds with the power turned on to turn the " S "display off. RS-232C communications are now enabled.
RETURNZONE2ON/OFF
DSP SIMULATION
STANDARD STATUSENTERPURE
DIRECTDIRECT/STEREO
MENUCURSOR
-
17
1. com/DSP Version display mode1.1. Operation specifi cationscom/DSP version display mode:When started up, the version information is displayed.Starting up:With the "RETURN" and "STATUS" buttons pressed, press the "ON/STANDBY" button to turn the power on.Now, press the "STATUS" button to the display the 2nd item information on the FL Display.
1.2. Display OrderError information(Refer to 1.3. Error display) qModel destination information wFirmware Package Version eMain -com/ROM version rMain 1st Boot Loader tSub -com/Sub FBL yDSP1/2 version uAudio/Video PLD iGUI FPGA Confi g oGUI SFLASH(PROGRAM/DATA) Q0Ethernet(DM860) 1st Boot Loader, Hardware ID Q1Ethernet(DM860) 2nd Boot Loader, Rhapsody Flag Q2Ethernet(DM860) IMAGE Q3Ethernet(DM860)MAC ADDRESS information Q4HD RADIO SDK/HD RADIO BBP (AVR-4311CIEU/EC only) Q5iPod Version Q6MultEQ Pro APP(Displayed when Audyssey Pro is complete) Q7MultEQ Pro ICL(Displayed when Audyssey Pro is complete
qModel destination information :
Upper A V R 4 3 1 1 E 3
Lower S / N . * * * * * * * * * *
wFirmware Package Version :
Upper F i r m . P a c k a g e
Lower V e r . : * * * *
eMain -com & ROM version :
Upper M a i n : * * . * *
Lower M a i n R O M : * * . * *
rMain 1st Boot Loader :
Upper M a i n F B L : * * . * *
Lower
tSub -com & Sub FBL :
Upper S u b : * * . * *
Lower S u b F B L : * * . * *
yDSP1/2 ROM :
Upper D S P 1 : * * . * *
Lower D S P 2 : * * . * *
uAudio/Video PLD :
Upper A u d i o P L D : * * . * *
Lower V i d e o P L D : * * . * *
iGUI FPGA Confi g :
Upper G U I C o n f i g :
Lower * * * * * * * *
-
18
oGUI SFLASH(PROGRAM/DATA) :
Upper G U I P R G : * * * * * * * *
Lower G U I D A T : * * * * * * * *
Q0Ethernet(DM860) 1st Boot Loader, Hardware ID :
Upper * E t h e r n e t F B L
Lower * * * * * * * * - A A
Q1Ethernet(DM860) 2nd Boot Loader, Rhapsody Flag :
Upper * E t h e r n e t S B L
Lower * * * * * * * * * * * * * - B B
Q2Ethernet(DM860) IMAGE :
Upper * E t h e r n e t I M G
Lower * * * * * * * * * * * * *
Q3Ethernet(DM860) MAC ADDRESS information :
Upper * E t h e r n e t M A C
Lower * * * * * * - * * * * * *
Q4HD RADIO SDK/HD RADIO BBP (AVR-4311CIEU/EC only) :
Upper * H D S D K : * * . * *
Lower * H D B B P : C 0 0 0 2 . 0 0 0
Q5iPod Version :
Upper i P o d D o c k : * * . * *
Lower
Q6MultEQ Pro APP(Displayed when Audyssey Pro is complete) :
Upper * M u l t E Q P r o A P P
Lower * * . * * . * * . * * * *
Q7MultEQ Pro ICL(Displayed when Audyssey Pro is complete) :
Upper * M u l t E Q P r o I C L
Lower * * . * * . * * . * * * *
-
19
1.3. Error displaySee the following table for each "Error information" display and its contents (status). Display order is q,w,e,r,t,y.
Condition State State
q Sub-com NG No response from Sub-com S U B E R R O R 0 1
w DIR NG No response from DIR D I R E R R O R 0 1
e DSP1 NG
When DSP boot, executing DSP reset makes no change to DSP FLAG0 port "H". D S P 1 E R R O R 0 1
No change to DSP FLAG0 port "H" before issuing DSP command. D S P 1 E R R O R 0 2
When DSP data read, executing WRITE="L" makes no change to ACK="H". D S P 1 E R R O R 0 3
When DSP data read, executing REQ="L" makes no change to ACK="L". D S P 1 E R R O R 0 4
When DSP data write, executing WRITE="H" makes no change to ACK="H". D S P 1 E R R O R 0 5
When DSP data write, executing REQ="L" makes no change to ACK="L". D S P 1 E R R O R 0 6
When DSP special code boot, executing DSP reset makes no change to DSP FLAG0 port "H". D S P 1 E R R O R 1 1
No change to DSP FLAG0 port "H" before issuing DSP special read command. D S P 1 E R R O R 1 2
No change to DSP FLAG0 port "H" before DSP version read. D S P 1 E R R O R 1 3
r DSP2 NG
When DSP boot, executing DSP reset makes no change to DSP FLAG0 port "H". D S P 2 E R R O R 0 1
No change to DSP FLAG0 port "H" before issuing DSP command. D S P 2 E R R O R 0 2
When DSP data read, executing WRITE="L" makes no change to ACK="H". D S P 2 E R R O R 0 3
When DSP data read, executing REQ="L" makes no change to ACK="L". D S P 2 E R R O R 0 4
When DSP data write, executing WRITE="H" makes no change to ACK="H". D S P 2 E R R O R 0 5
When DSP data write, executing REQ="L" makes no change to ACK="L". D S P 2 E R R O R 0 6
When DSP special code boot, executing DSP reset makes no change to DSP FLAG0 port "H". D S P 2 E R R O R 1 1
No change to DSP FLAG0 port "H" before issuing DSP special read command. D S P 2 E R R O R 1 2
No change to DSP FLAG0 port "H" before DSP version read. D S P 2 E R R O R 1 3
t EEPROM NG Error appeared in EEPROM checksum.(*** is a block address number.) E 2 P R O M E R R * * *
y Both SUB/DSP /EEPROM OK (No error display, version display only)
-
20
2. Errors checking mode (Displaying the protection history)2.1. Operation specifi cationsError mode (Displaying the protection history):When started up, the error information is displayed.
Starting up:All model commonnessWith the "STATUS" and "MENU" buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set.Now, press the "STATUS" button to turn on the FL display.
2.2. About the display on the FL displayWhen the "STATUS" button is pressed after setting the error (protection history display) mode, a history like the one shown below is displayed, depending on the conditions.(1) Normally (when there has been no protection incident)
Upper P R O T E C T H I S T O R Y
Lower : N O P R O T E C T
(2) For ASO (when the last protection incident was ASO protection)
Upper P R O T E C T H I S T O R Y
Lower : A S O
Cause: The line between speaker terminals is shorted, or use speakers having impedance less than that specifi ed. Supplementary information: As the excess current is detected after operation of the speaker relay, the shorted
speaker terminal and the connected speaker can be identifi ed.
Turning on the power without correcting the abnormality will cause the protection function to work about 5 seconds later and the power supply will be shut off.
(3) For DC (when the last protection incident was DC protection)
Upper P R O T E C T H I S T O R Y
Lower : D C
Cause: DC output of the power amplifi er is abnormal.
Turning on the power without correcting the abnormality will cause the protection function to work about 5 seconds later and the power supply will be shut off.
(4) For THERMAL RADIATOR (when the last protection incident was THERMAL RADIATOR protection)
Upper P R O T E C T H I S T O R Y
Lower T H E R M A L R A D I A T O R
Cause: The temperature of the heat sink is excessive.
Turning on the power without correcting the abnormality will cause the protection function to work about 5 seconds later and the power supply will be shut off.
(5) For THERMAL BRIDGE (when the last protection incident was THERMAL BRIDGE protection)
Upper P R O T E C T H I S T O R Y
Lower T H E R M A L B R I D G E
Cause: The temperature of the Bridge Diode is excessive.
Turning on the power without correcting the abnormality will cause the protection function to work about 5 seconds later and the power supply will be shut off.
z Additional causes of protection can be due to loose connections, associated components, Microprocessor, etc.
When the "STATUS" button is pressed again after the above protection history is displayed, the normal display reappears.
-
21
2.3. Clearing the protection historyThere are two ways to clear the protection history, as described below.
(1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds.
Upper P R O T E C T H I S T O R Y
Lower : T H E R M A L T R
Press and hold in the "ENTER" button for 3 seconds.
Upper P R O T E C T H I S T O R Y
Lower C L E A R
The above is displayed and the protection history is cleared.
Upper P R O T E C T H I S T O R Y
Lower : N O P R O T E C T
(2) Initialize. (Refer to "Initializing AV SURROUND RECEIVER" 5 page.)
b If you want to save a backup, use the method in 2.3.(1) above.
Warning indication by the POWER LEDIf the power is turned off when a protection incident has been detected, the POWER LED (red) fl ashes as a warning according to the conditions in which the protection incident occurred.(1) ASO/DC PROTECTION : Flashes in cycles of 0.5 seconds (0.25 seconds lit, 0.25 seconds off)(2) THERMAL PROTECTION : Flashes in cycles of 2 seconds (1 second lit, 1 second off)
-
22
JIG FOR SERVICINGWhen you repair the printing board, you can use the following JIG (Extension cable kit). Please order to DENON Offi cial Service. Distributor in your region if necessary.
Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
8U-110084S : EXTENSION UNIT KIT
Connection of PCB HDMI JIG-Preparation-8U-110084S : EXTENSION UNIT KIT : 1 SetInsulation sheet (Do not supply it) : 1 sheetGround lead (Do not supply it) : 1 pcs
-Procedures-(1) Disconnect the connector board.
(2) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB.Connect the ground point of PCB to the chassis with a ground lead or the like.Connect the four extension jig cables.
DIGITAL UNIT(8U-310053)
Board to board
Ground lead(HDMI connector to Bakpanel chassis)
DIGITAL UNIT(8U-310053)
Insulation sheet
Extension JIG cables
-
23
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONEWhen replaced of the U-PRO (Microprocessor) or the Flash ROM, confi rm contents of the following.
PWB Name Ref. No. Description After replaced Remark
DIGITAL U6703 R5F64169DFD B SOFTWARE: MainDIGITAL U6701 W19B160BBT7H B SOFTWARE: Main ROMDIGITAL U6901 R5F3650KNFB B SOFTWARE: SubDIGITAL U3403 EN29LV160BB-70TIP B SOFTWARE: DSP1 ROMDIGITAL U3602 EN29LV160BB-70TIP B SOFTWARE: DSP2 ROMDIGITAL U3201 EPM240T100C5N C SOFTWARE: Audio PLDDIGITAL U1800 EPM1270F256C5N C SOFTWARE: Video PLDDIGITAL U1510 EPCS16SI8N C SOFTWARE: GUI confi gDIGITAL U5002 NAND01GW3B2CN6E B SOFTWARE: DM860 ROM
After replacedA : Mask ROM (With software). No need write-in of software to the microprocessor.B : Flash ROM (With software). Usually, no need write-in of software. But, when the software was updated, you should be
write-in of the new software to the microprocessor or fl ash ROM. Please check the software version. C : Empty Flash ROM (Without software). You should be write-in of the software to the microprocessor or fl ash ROM.
Refer to "Update procedure" or "writing procedure", when you should be write-in the software.
VERSION UPGRADE PROCEDURE OF FIRMWAREYou can update by downloading the latest fi rmware from the Internet.
1. Connecting to the Network(1) System Requirement Internet Connection by Broadband Circuit Modem Router Ethernet cable (CAT-5 or greater recommended)
(2) Setting
Modem
Internet
Computer
LAN port/Ethernetconnector
ETHERNETconnector
RouterTo WAN port
To LAN port
To LAN port
-
24
2. Check for Update and UpdateCheck if the latest fi rmware exists. You can also check approximately how long it will take to complete an update.(1) Press the MENU button on the remote control to display the GUI menu.(2) Use the cursor buttons to select "Manual Setup" "Option Setup" "Firmware Update" "Update Check".(3) Press the ENTER buttom. The latest version of the fi rmware uploaded to the web is displayed. If the latest fi rmware version is on the web, proceed to (4). If the latest fi rmware is already installed, press the MENU button to close the menu.
(4) Use the cursor buttons to select "Update", then press the ENTER button. During update, the power indicator lights red and the GUI screen is shut down. And a rough remaining time is
indicated on the display. When updating is complete the power indicator lights green and normal status is resumed.
(5) Press the MENU button to close the menu.--- Cautions on Firmware Update --- In order to use these functions, you must have the correct system requirements and settings for a broadband Internet
connection. Do not turn off the power until updating is completed.
Even with a broadband connection to the Internet, approximately about 1 hour is required for the updating procedure to be completed.Once updating starts, normal operations on the AVR-4311CI/4311 cannot be performed until updating is completed. Also, setting items of the GUI menu of AVR-4311CI/4311 or setting items of the image adjustment may be initialized.Make a note of the settings before updating, and set them again after updating.
3. About the error codeSee the chart below for error codes, details of faults, and coping strategies when fi rmware updates are performed through DPMS (Denon Product Management Server).
Error Code Details of Error code Display Coping strategies
01 Log-in to DPMS has failed.L o g i n f a i l e d
0 1
Reset and update again.Carry out the update in an environment that has little network load.
02 Line, etc., is busy when logging into DPMS.S e r v e r i s b u s y
0 2
Carry out the update in an environment that has little network load.
03 Connection to DPMS failed.C o n n e c t i o n f a i l
0 3
Check the network connection.Carry out the update in an environment that has little network load.
04 Firmware fi le data was requested but error message was received.C o n n e c t i o n f a i l
0 4
Check the network connection.Carry out the update in an environment that has little network load.
05 Firmware fi le data was requested but it timed out.C o n n e c t i o n f a i l
0 5
Check the network connection.Carry out the update in an environment that has little network load.
06 Firmware fi le data was requested but error message was received.C o n n e c t i o n f a i l
0 6
Check the network connection.Carry out the update in an environment that has little network load.
07 All fi rmware fi le data was requested but it timed out.C o n n e c t i o n f a i l
0 7
Check the network connection.Carry out the update in an environment that has little network load.
08Main CPU fi rmware fi le data was requested but error message was received.
C o n n e c t i o n f a i l
0 8
Check the network connection.Carry out the update in an environment that has little network load.
-
25
Error Code Details of Error code Display Coping strategies
09 Main CPU fi rmware fi le data was requested but it timed out.C o n n e c t i o n f a i l
0 9
Check the network connection.Carry out the update in an environment that has little network load.
0A Error (NG) message received when downloading Main CPU fi rmware.D o w n l o a d f a i l
0 A
Check the network connection.Carry out the update in an environment that has little network load.
0BError (line congestion) message received when downloading Main CPU fi rmware.
D o w n l o a d f a i l
0 B
Check the network connection.Carry out the update in an environment that has little network load.
0CError (connection failure) message received when downloading Main CPU fi rmware.
D o w n l o a d f a i l
0 C
Check the network connection.Carry out the update in an environment that has little network load.
0D
Data acquisition failed (timed out) when downloading Main CPU fi rmware. Received Package Version is wrong.
C o n n e c t i o n f a i l
0 D
Check the network connection.Carry out the update in an environment that has little network load.
10Main CPU failed to receive fi rmware for rewriting sent fromDM860 (when timed out).
M a i n * * * m i n
U p d a t i n g f a i l 1 0
Turn the power off then back on. Updating starts automatically.
11Main CPU failed to receive fi rmware for rewriting sent from DM860 (when an error )
M a i n * * * m i n
U p d a t i n g f a i l 1 1
Turn the power off then back on. Updating starts automatically.
12
There was invalid data in the fi rmware for rewriting sent from DM860 to Main CPU (when a Check Sum error).
M a i n * * * m i n
U p d a t i n g f a i l 1 2
Turn the power off then back on. Updating starts automatically.
13 The deletion of block data failed before rewriting Main CPU.M a i n * * * m i n
E r a s e f a i l 1 3
Turn the power off then back on. Updating starts automatically.
14 The rewriting of block data failed when rewriting Main CPU.M a i n * * * m i n
U p d a t i n g f a i l 1 4
Turn the power off then back on. Updating starts automatically.
15 The data verifi cation was invalid after rewriting Main CPU.M a i n * * * m i n
U p d a t e C h e c k N G 1 5
Turn the power off then back on. Updating starts automatically.
36Log-in to DPMS has failed when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
L o g i n f a i l e d
3 6
Carry out the update in an environment that has little network load.
37
Line, etc., is busy when logging into DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S e r v e r i s b u s y
3 7
Carry out the update in an environment that has little network load.
38Connection to DPMS failed when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
C o n n e c t i o n f a i l
3 8
Check the network connection.Carry out the update in an environment that has little network load.
39Connection to DPMS timed out when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
C o n n e c t i o n f a i l
3 9
Check the network connection.Carry out the update in an environment that has little network load.
3AError (NG) message received when downloading fi rmware when rewriting Main CPU.
D o w n l o a d f a i l
3 A
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
-
26
Error Code Details of Error code Display Coping strategies
3BError (line congestion) message received when downloading fi rmware when rewriting Main CPU.
D o w n l o a d f a i l
3 B
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
3CError (connection failure) message received when downloading fi rmware when rewriting Main CPU.
D o w n l o a d f a i l
3 C
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
50Log-in to DPMS has failed when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
L o g i n f a i l e d 5 0
Carry out the update in an environment that has little network load.
51
Line, etc., is busy when logging into DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
S e r v e r i s b u s y 5 1
Carry out the update in an environment that has little network load.
52Connection to DPMS failed when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
C o n n e c t i o n F a i l 5 2
Check the network connection.Carry out the update in an environment that has little network load.
54
Error message received regarding fi rmware data after logging in to DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
U p d a t i n g f a i l 5 4
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
55
When rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD, request was made for fi rmware data after logging in to DPMS, but it timed out.
S u b * * * m i n
U p d a t i n g f a i l 5 5
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
56
Failure to download fi rmware after logging in to DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
D o w n l o a d f a i l 5 6
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
57
Firmware download error received (line congestion) after logging in to DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
S e r v e r i s b u s y 5 7
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
58
Firmware download error received (connection failure) after logging in to DPMS when rewriting fi rmware such as Sub CPU, DSP, FPGA, and PLD.
S u b * * * m i n
C o n n e c t i o n F a i l 5 8
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
5ANACK received when "C" command sent to Sub CPU, DSP, FPGA, PLD etc.
S u b * * * m i n
C o n n e c t i o n F a i l 5 A
Turn the power off then back on. Updating starts automatically.
5BNACK received when "L" command sent to Sub CPU, DSP, FPGA, PLD etc.
S u b * * * m i n
U p d a t i n g f a i l 5 B
Turn the power off then back on. Updating starts automatically.
5C
Sub CPU, DSP, FPGA, PLD etc. failed to receive fi rmware for rewriting sent from DM860 (when timed out).
S u b * * * m i n
U p d a t i n g f a i l 5 C
Turn the power off then back on. Updating starts automatically.
5D
Sub CPU, DSP, FPGA, PLD etc. failed to receive fi rmware for rewriting sent from DM860 (when an error).
S u b * * * m i n
U p d a t i n g f a i l 5 D
Turn the power off then back on. Updating starts automatically.
5E
Invalid data in fi rmware such as Sub CPU, DSP, FPGA, and PLD for rewriting sent from DM860 (when a Check Sum error).
S u b * * * m i n
U p d a t i n g f a i l 5 E
Turn the power off then back on. Updating starts automatically.
5F
Invalid data in fi rmware such as Sub CPU, DSP, FPGA, and PLD for rewriting sent from DM860 (invalid data received).
S u b * * * m i n
U p d a t i n g f a i l 5 F
Turn the power off then back on. Updating starts automatically.
-
27
Error Code Details of Error code Display Coping strategies
60NACK received when "P" command sent to Sub CPU, DSP, FPGA, PLD etc.
S u b * * * m i n
U p d a t i n g f a i l 6 0
Turn the power off then back on. Updating starts automatically.
61NACK received when "I" command sent to Sub CPU, DSP, FPGA, PLD etc.
S u b * * * m i n
U p d a t e C h e c k N G 6 1
Turn the power off then back on. Updating starts automatically.
62 Start failure of Sub -com. S u b * * * m i n
U p d a t i n g f a i l 6 2
Turn the power off then back on. Updating starts automatically. (AVR-4810 deal with this matter from the fi rst and AVR-4310 deal with this matter by the update.)
80 Failure to acquire serial fl ash data and before deleting serial fl ash.O S D * * * m i n
U p d a t i n g f a i l 8 0
Turn the power off then back on. Updating starts automatically.
81 Failure to delete data before rewriting serial fl ash.O S D * * * m i n
U p d a t i n g f a i l 8 1
Turn the power off then back on. Updating starts automatically.
82Failure to receive fi rmware for serial fl ash rewriting sent by DM860 (when timed out).
O S D * * * m i n
U p d a t i n g f a i l 8 2
Turn the power off then back on. Updating starts automatically.
83Failure to receive fi rmware for serial fl ash rewriting sent by DM860 (when an error).
O S D * * * m i n
U p d a t i n g f a i l 8 3
Turn the power off then back on. Updating starts automatically.
84Failure to receive fi rmware for serial fl ash rewriting sent by DM860 (when a Check Sum error).
O S D * * * m i n
U p d a t i n g f a i l 8 4
Turn the power off then back on. Updating starts automatically.
85Failure to receive fi rmware for serial fl ash rewriting sent by DM860 (when invalid data received).
O S D * * * m i n
U p d a t i n g f a i l 8 5
Turn the power off then back on. Updating starts automatically.
86 Failure to rewrite when writing data in serial fl ash.O S D * * * m i n
U p d a t i n g f a i l 8 6
Turn the power off then back on. Updating starts automatically.
A0Failure to acquire (Application Mode) IP address before rewriting DM860 (AutoIP).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 0
Check the network connection.Carry out the update in an environment that has little network load.
A1Failure to acquire (Application Mode) IP address before rewriting DM860 (when timed out).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 1
Check the network connection.Carry out the update in an environment that has little network load.
A2Notifi cation of invalid login via DPMS access when rewriting DM860 related fi rmware (Application Mode).
E t h e r I M G * * * m i n
L o g i n f a i l e d A 2
Check the network connection.Carry out the update in an environment that has little network load.
A3
Notifi cation of line congestion via DPMS access when rewriting DM860 related fi rmware (Application Mode).
E t h e r I M G * * * m i n
S e r v e r i s b u s y A 3
Check the network connection.Carry out the update in an environment that has little network load.
A4
Notifi cation of connection failure via DPMS access when rewriting DM860 related fi rmware (Application Mode).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 4
Check the network connection.Carry out the update in an environment that has little network load.
A6
Firmware data error message received after DPMS login when rewriting DM860 related fi rmware (Application Mode).
E t h e r I M G * * * m i n
U p d a t i n g f a i l A 6
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
-
28
Error Code Details of Error code Display Coping strategies
A7
When rewriting DM860 related fi rmware (Application Mode), request was made for fi rmware data after DPMS login but it timed out.
E t h e r I M G * * * m i n
U p d a t i n g f a i l A 7
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
A8Failure to acquire (Boot Loader Mode) IP address before rewriting DM860 (AutoIP).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 8
Check the network connection.Carry out the update in an environment that has little network load.
A9Failure to acquire (Boot Loader Mode) IP address before rewriting DM860 (when timed out).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 9
Check the network connection.Carry out the update in an environment that has little network load.
AA
Notifi cation of invalid login via DPMS access when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
L o g i n f a i l e d A A
Check the network connection.Carry out the update in an environment that has little network load.
AB
Notifi cation of line congestion via DPMS access when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
S e r v e r i s b u s y A B
Check the network connection.Carry out the update in an environment that has little network load.
AC
Notifi cation of connection failure via DPMS access when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A C
Check the network connection.Carry out the update in an environment that has little network load.
AE
Firmware download error message received (when download fails) when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
D o w n l o a d f a i l A E
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
AF
Firmware download error message received (line congestion) when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
S e r v e r i s b u s y A F
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
B0
Firmware download error message received (connection failure) when rewriting DM860 related fi rmware (Boot Loader Mode).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l B 0
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
B2 Error message received when rewriting DM860 related fi rmware.E t h e r I M G * * * m i n
U p d a t i n g f a i l B 2
Turn the power off then back on. Updating starts automatically.Carry out the update in an environment that has little network load.
-
29
Device display when fi rmware updatedTarget of devide when fi rmware updated.
Target of device Display Error cpde
MainM a i n * * * m i n
U p d a t i n g
10~1536~3C
Main ROMM a i n R O M * * * m i n
U p d a t i n g
10~1536~3C
SubS u b * * * m i n
U p d a t i n g
50~5254~585A~62
Audio PLDA P L D * * * m i n
U p d a t i n g
50~5254~585A6280~86
Gui Confi gG U I C o n f * * * m i n
U p d a t i n g
50~5254~585A6280~86
Video PLDV P L D * * * m i n
U p d a t i n g
50~5254~585A6280~86
DSP1D S P 1 * * * m i n
U p d a t i n g
50~5254~585A~62
DSP2D S P 2 * * * m i n
U p d a t i n g
50~5254~585A~62
GUI Serial FlashG U I F l a s h * * * m i n
U p d a t i n g
50~5254~585A6280~86
DM860 Boot LoaderE t h e r S B L * * * m i n
U p d a t i n g
A0~A4A6~ACAE~B0B2
DM860 ImageE t h e r I M G * * * m i n
U p d a t i n g
A0~A4A6~ACAE~B0B2
-
30
SURROUND MODES AND PARAMETERSSy
mbo
ls in
the
tabl
eS
Thi
s in
dica
tes
the
audi
o ou
tput
cha
nnel
s or
sur
roun
d pa
ram
eter
s th
at c
an b
e se
t.D
Thi
s in
dica
tes
the
audi
o ou
tput
cha
nnel
s. T
he o
utpu
t ch
anne
ls d
epen
d on
the
set
tings
of
Spe
aker
Con
g.
.
Surro
und
mod
eCh
anne
l out
put
Surro
und
Para
met
ers
Fron
t L/
RCe
nter
Surro
und
L/R
Surro
und
back
L/
RFr
ont h
eigh
t L/
RFr
ont w
ide
L/R
Subw
oofe
rM
ode
Cine
ma
EQ.
DRC
z14z
17D.
COM
Pz
15z
17LF
Ez
16z
17De
lay
Tim
e
DIRE
CT/P
URE
DIRE
CT (2
-cha
nnel
)z1
SDz
9S
S
DIRE
CT/P
URE
DIRE
CT (M
ulti-
chan
nel)z
1S
DD
Dz
3Dz
3Dz
3D
SS
S
DSD
DIRE
CT (2
-cha
nnel
)S
DSD
DIRE
CT (M
ulti-
chan
nel)
SD
DD
STER
EOS
DS
SS
EXT.
IN/P
URE
DIRE
CT E
XTz
2S
DD
DD
MUL
TI C
H IN
SD
DD
Dz
4D
SS
WID
E SC
REEN
SD
DD
Dz
5Dz
6D
SS
SS
DOLB
Y PR
O LO
GIC g
zS
DD
DD
DSz
10S
SS
DOLB
Y PR
O LO
GIC g
xS
DD
DD
SSz
11S
S
DOLB
Y PR
O LO
GIC g
SD
DD
SSz
12S
S
DOLB
Y PR
O LO
GIC
SD
DD
SSz
12S
S
DOLB
Y PR
O LO
GIC g
x A-
DSX
SD
DD
Dz
7Dz
8D
SSz
11S
S
DOLB
Y PR
O LO
GIC g
A-D
SXS
DD
Dz
7Dz
8D
SSz
12S
S
DOLB
Y PR
O LO
GIC
A-DS
XS
DD
Dz
7Dz
8D
SSz
12S
S
DTS
NEO
:6S
DD
DD
SSz
11S
S
DTS
NEO
:6 A
-DSX
SD
DD
Dz
7Dz
8D
SSz
11S
S
Audy
ssey
DSX
SD
DD
Dz
7Dz
8D
Sz
13S
SS
DOLB
Y DI
GITA
LS
DD
DDz
4D
Sz
13S
S
DOLB
Y DI
GITA
L Pl
usS
DD
DDz
4D
Sz
13S
S
DOLB
Y Tr
ueHD
SD
DD
Dz
4D
Sz
13S
S
DTS
SURR
OUN
DS
DD
DDz
4D
Sz
13S
S
DTS
96/2
4S
DD
DDz
4D
Sz
13S
S
DTS-
HDS
DD
DDz
4D
Sz
13S
S
DTS
Expr
ess
SD
DD
Dz
4D
Sz
13S
S
MUL
TI C
H ST
EREO
SD
DD
Dz
5Dz
6D
SS
SUPE
R ST
ADIU
MS
DD
DDz
5Dz
6D
SS
S
ROCK
ARE
NA
SD
DD
Dz
5Dz
6D
SS
S
JAZZ
CLU
BS
DD
DDz
5Dz
6D
SS
S
CLAS
SIC
CON
CERT
SD
DD
Dz
5Dz
6D
SS
S
MON
O M
OVIE
SD
DD
Dz
5Dz
6D
SS
S
VIDE
O GA
ME
SD
DD
Dz
5Dz
6D
SS
S
MAT
RIX
SD
DD
Dz
5Dz
6D
SS
SS
VIRT
UAL
SDz
9S
SS
z1
Dur
ing
play
back
in P
UR
E D
IRE
CT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in D
IRE
CT
mod
e.z
2 D
urin
g pl
ayba
ck in
PU
RE
DIR
EC
T E
XT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in E
XT.
IN m
ode.
z3
A s
igna
l for
eac
h ch
anne
l con
tain
ed in
an
inpu
t si
gnal
is o
utpu
t as
aud
io.
z4
If
Sur
roun
d P
aram
eter
s
P
Lgz
Hei
ght
is s
et t
o O
N,
sou
nd is
out
put
from
the
fro
nt h
eigh
t sp
eake
rs.
z5
If
Sur
roun
d P
aram
eter
s
S
peak
er
is s
et t
o H
eigh
t o
r H
eigh
t/W
ide
, sou
nd is
out
put
from
the
fro
nt h
eigh
t sp
eake
rs.
z6
If
Sur
roun
d P
aram
eter
s
S
peak
er
is s
et t
o W
ide
or
Hei
ght/
Wid
e, s
ound
is o
utpu
t fr
om t
he f
ront
wid
e sp
eake
rs.
z7
If
Aud
ysse
y D
SX
is
set
to
ON
Hei
ght
or
O
NH
eigh
t/W
ide
, s
ound
is o
utpu
t fr
om t
he f
ront
hei
ght
spea
kers
.
z8
If
Aud
ysse
y D
SX
is
set
to
ON
Wid
e
or
ON
Hei
ght/
Wid
e,
sou
nd is
out
put
from
the
fro
nt w
ide
spea
kers
.z
9 O
nly
whe
n S
ubw
oofe
r M
ode
is s
et t
o L
FE+
Mai
n, s
ound
is o
utpu
t fr
om t
he s
ubw
oofe
r.z
10
If t
his
surr
ound
mod
e is
sel
ecte
d, o
nly
the
Hei
ght
mod
e se
ttin
g is
ava
ilabl
e fo
r S
urro
und
Par
amet
ers
Mod
e.
z11
Th
is it
em c
an b
e se
lect
ed w
hen
Sur
roun
d P
aram
eter
s
M
ode
is s
et t
o C
inem
a.
z12
Th
is it
em c
an b
e se
lect
ed w
hen
Sur
roun
d P
aram
eter
s
M
ode
is s
et t
o C
inem
a o
r P
ro L
ogic
.z
13
This
item
can
not
be s
et w
hen
Sur
roun
d P
aram
eter
s
S
urro
und
Bac
k is
set
to
PLg
x M
usic
.z
14
This
item
can
be
sele
cted
whe
n a
Dol
by T
rueH
D s
igna
l is
play
ed.
z15
Th
is it
em c
an b
e se
lect
ed w
hen
a D
olby
Dig
ital o
r D
TS s
igna
l is
play
ed.
z16
Th
is it
em c
an b
e se
lect
ed w
hen
a D
olby
Dig
ital o
r D
TS s
igna
l or
DV
D-A
udio
is p
laye
d.z
17
This
item
can
not
be s
et w
hen
Dol
by V
olum
e is
set
to
ON
.
-
31
Surro
und
mod
e
Surro
und
Para
met
ers
Effe
ctEf
fect
Lev
elRo
om S
izeAF
DMz
11Su
rroun
d Ba
ckPLg
z Hei
ghtz
18He
ight
Gai
nz19
Spea
ker
Subw
oofe
rPR
O LO
GIC g
/gx
Mus
ic m
ode
only
NEO
:6 M
usic
m
ode
only
Pano
ram
aDi
men
sion
Cent
er W
idth
Cent
er Im
age
DIRE
CT/P
URE
DIRE
CT (2
-cha
nnel
)z1
Sz
9
DIRE
CT/P
URE
DIRE
CT (M
ulti-
chan
nel)z
1
DSD
DIRE
CT (2
-cha
nnel
)
DSD
DIRE
CT (M
ulti-
chan
nel)
STER
EO
EXT.
IN/P
URE
DIRE
CT E
XTz
2
MUL
TI C
H IN
SS
SS
WID
E SC
REEN
SS
S
DOLB
Y PR
O LO
GIC g
zS
S
DOLB
Y PR
O LO
GIC g
xS
SS
SS
DOLB
Y PR
O LO
GIC g
SS
SS
S
DOLB
Y PR
O LO
GIC
SS
DOLB
Y PR
O LO
GIC g
x A-
DSX
SS
SS
DOLB
Y PR
O LO
GIC g
A-D
SXS
SS
S
DOLB
Y PR
O LO
GIC
A-DS
XS
DTS
NEO
:6S
S
DTS
NEO
:6 A
-DSX
SS
Audy
ssey
DSX
SS
DOLB
Y DI
GITA
LS
SS
DOLB
Y DI
GITA
L Pl
usS
SS
DOLB
Y Tr
ueHD
SS
S
DTS
SURR
OUN
DS
SS
DTS
96/2
4S
SS
DTS-
HDS
SS
DTS
Expr
ess
SS
S
MUL
TI C
H ST
EREO
SUPE
R ST
ADIU
MS
S
ROCK
ARE
NA
SS
S
JAZZ
CLU
BS
SS
CLAS
SIC
CON
CERT
SS
S
MON
O M
OVIE
SS
S
VIDE
O GA
ME
SS
S
MAT
RIX
S
VIRT
UAL
z1
Dur
ing
play
back
in P
UR
E D
IRE
CT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in D
IRE
CT
mod
e.z
2 D
urin
g pl
ayba
ck in
PU
RE
DIR
EC
T E
XT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in E
XT.
IN m
ode.
z9
Onl
y w
hen
Sub
woo
fer
Mod
e is
set
to
LFE
+M
ain
, sou
nd is
out
put
from
the
sub
woo
fer.
z11
Th
is it
em c
an b
e se
lect
ed w
hen
a D
olby
Dig
ital o
r D
TS s
igna
l or
DV
D-A
udio
is p
laye
d.z
18
If
Spe
aker
Con
g.
Fron
t H
eigh
t is
set
to
Non
e, t
his
item
can
not
be s
elec
ted.
z19
Th
is it
em c
an b
e se
lect
ed w
hen
Sur
roun
d P
aram
eter
s
P
Lgz
Hei
ght
is s
et t
o O
N.
-
32
Surro
und
mod
eSu
bwoo
fer A
tt.To
nez
20Au
dyss
ey S
ettin
gsA-
DSX
Soun
dsta
geDo
lby
Volu
me
REST
ORER
z
29M
ultE
Q X
T 32
Dyna
mic
EQ
z21
Dyna
mic
Vo
lum
e z
22Au
dyss
ey D
SX
z
25St
age
Heig
htz
26St
age
Wid
ez
27Do
lby
Volu
me
Volu
me
Leve
ler
z28
Volu
me
Mod
eler
z28
DIRE
CT/P
URE
DIRE
CT (2
-cha
nnel
)z1
DIRE
CT/P
URE
DIRE
CT (M
ulti-
chan
nel)z
1
DSD
DIRE
CT (2
-cha
nnel
)
DSD
DIRE
CT (M
ulti-
chan
nel)
STER
EOS
SS
SS
SS
S
EXT.
IN/P
URE
DIRE
CT E
XTz
2S
MUL
TI C
H IN
SS
SS
SS
SS
WID
E SC
REEN
SS
SS
SS
SS
DOLB
Y PR
O LO
GIC g
zS
SS
SS
SS
S
DOLB
Y PR
O LO
GIC g
xS
SS
SS
SS
SS
DOLB
Y PR
O LO
GIC g
SS
SS
SS
SS
S
DOLB
Y PR
O LO
GIC
SS
SS
SS
SS
S
DOLB
Y PR
O LO
GIC g
x A-
DSX
SS
SS
SS
SS
SS
S
DOLB
Y PR
O LO
GIC g
A-D
SXS
SS
SS
SS
SS
SS
DOLB
Y PR
O LO
GIC
A-DS
XS
SS
SS
SS
SS
SS
DTS
NEO
:6S
SS
SS
SS
SS
DTS
NEO
:6 A
-DSX
SS
SS
SS
SS
SS
S
Audy
ssey
DSX
SS
SS
SS
SS
SS
DOLB
Y DI
GITA
LS
SS
SS
SS
S
DOLB
Y DI
GITA
L Pl
usS
SS
SS
SS
S
DOLB
Y Tr
ueHD
SS
SS
SS
SS
DTS
SURR
OUN
DS
SS
SS
SS
S
DTS
96/2
4S
SS
SS
SS
S
DTS-
HDS
SS
SS
SS
S
DTS
Expr
ess
SS
SS
SS
SS
MUL
TI C
H ST
EREO
SS
SS
SS
SS
SUPE
R ST
ADIU
MDz
23S
SS
SS
SS
ROCK
ARE
NA
Dz
24S
SS
SS
SS
JAZZ
CLU
BS
SS
SS
SS
S
CLAS
SIC
CON
CERT
SS
SS
SS
SS
MON
O M
OVIE
SS
SS
SS
SS
VIDE
O GA
ME
SS
SS
SS
SS
MAT
RIX
SS
SS
SS
SS
VIRT
UAL
SS
SS
SS
SS
z1
Dur
ing
play
back
in P
UR
E D
IRE
CT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in D
IRE
CT
mod
e.z
2 D
urin
g pl
ayba
ck in
PU
RE
DIR
EC
T E
XT
mod
e, t
he s
urro
und
para
met
ers
are
the
sam
e as
in E
XT.
IN m
ode.
z20
Th
is it
em c
anno
t be
set
whe
n D
ynam
ic E
Q
is s
et t
o O
N
or
Dol
by V
olum
e is
set
to
ON
.z
21
This
item
can
not
be s
et w
hen
Mul
tEQ
XT
32
is s
et t
o O
FF
or
Man
ual
.z
22
This
item
can
not
be s
et w
hen
Dyn
amic
EQ
is
set
to
OFF
.z
23
In t
his
surr
ound
mod
e, b
ass
is +
6 dB
, and
tre
ble
is +
4 dB
. (D
efau
lt)z
24
In t
his
surr
ound
mod
e, b
ass
is +
6 dB
, and
tre
ble
is 0
dB
. (D
efau
lt)
z25
Th
is it
em c
an n
ot b
e se
lect
ed w
hen
Sur
roun
d P
aram
eter
s
P
Lgz
Hei
ght
is s
et t
o O
N.
z26
Th
is it
em c
an b
e se
lect
ed w
hen
A-D
SX
Sou
ndst
age
Aud
ysse
y D
SX
is
set
to
ON
-Hei
ght-
or
O
N-
Hei
ght/
Wid
e.
z27
Th
is it
em c
an b
e se
lect
ed w
hen
A-D
SX
Sou
ndst
age
Aud
ysse
y D
SX
is
set
to
ON
-Wid
e-
or
ON
-H
eigh
t/W
ide
.z
28
This
item
can
not
be s
elec
ted
whe
n "D
olby
Vol
ume"
is s
et t
o "O
FF".
z29
Th
is it
em c
an b
e se
t w
hen
the
inpu
t si
gnal
is a
nalo
g, P
CM
48
kHz
or 4
4.1
kHz.
-
33
Sym
bols
in th
e ta
ble
F T
his
indi
cate
s th
e de
faul
t su
rrou
nd m
ode.
D T
his
indi
cate
s th
e su
rrou
nd m
ode
that
is
xed
whe
n A
FDM
is
set
to
ON
.S
Thi
s in
dica
tes
the
sele
ctab
le s
urro
und
mod
e.
Surro
und
mod
eN
OTE
Inpu
t sig
nal t
ypes
and
form
ats
ANAL
OG P
CM(m
ulti
ch)
PCM
(2ch
)
WM
A/M
P3/
MPE
G-4
AAC/
FLAC
/W
AV
DTS-
HDDT
S-HD
LB
RDT
SDO
LBY
DOLB
Y DI
GITA
LSu
per A
udio
CD
DTS-
HD
Mas
ter
Audi
o
DTS-
HD
High
Re
solu
tion
Audi
o
DTS
EXPR
ESS
DTS
ES
DSCR
T (W
ith F
lag)
DTS
ES
MTR
X (W
ith F
lag)
DTS
(5.1
ch)
DTS
96/2
4DO
LBY
True
HD
DOLB
Y DI
GITA
L Pl
us
DOLB
Y DI
GITA
L EX
(W
ith F
lag)
DOLB
Y DI
GITA
L EX
(W
ith n
o Fl
ag)
DOLB
Y DI
GITA
L (5
.1ch
)
DOLB
Y DI
GITA
L (2
ch)
DSD
(mul
ti ch
)DS
D(2
ch)
DTS
SURR
OUN
DDT
S-HD
MST
Rz
4F
DTS-
HD H
I RES
z4
F
DTS
ES D
SCRT
6.1
z1z
4F
DDT
S ES
MTR
X6.1
z1z
4F
DDT
S SU
RROU
ND
z4
SS
F
DTS
96/2
4z
4F
DTS
(HD
) + P
Lgx
CIN
EMA
z2z
4S
SS
SS
SS
DTS
(HD
) + P
Lgx
MUS
ICz
1z4
SS
SS
SS
S
DTS
(HD
) + P
Lgz
z3
SS
SS
SS
S
DTS
EXPR
ESS
z4
F
DTS
(HD
) + N
EO:6
z1z
4S
SS
SS
S
DTS
NEO
:6 C
INEM
Az
5S
SS
SS
DTS
NEO
:6 M
USIC
z5
SS
SS
S
DTS
NEO
:6 C
INEM
A A-
DSX
z6
SS
SS
S
DTS
NEO
:6 M
USIC
A-D
SXz
6S
SS
SS
Audy
ssey
DSX
z6
SS
SS
SS
S
DOLB
Y SU
RROU
ND
DOLB
Y Tr
ueHD
z4
F
DOLB
Y DI
GITA
L+z
4F
DOLB
Y DI
GITA
L EX
z1z
4S
SS
DOLB
Y (D
+) (H
D) +
EXz
1z4
SS
DOLB
Y DI
GITA
Lz
4S
FF
DOLB
Y (D
) (D+
) (HD
) +PLg
x CI
NEM
Az
2z4
SS
F D
SS
DOLB
Y (D
) (D+
) (HD
) +PLg
x M
USIC
z1z
4S
SS
SS
DOLB
Y (D
) (D+
) (HD
) +PLg
zz
3S
SS
SS
DOLB
Y PR
O LO
GIC g
x CI
NEM
Az
1S
SS
SS
DOLB
Y PR
O LO
GIC g
x M
USIC
z1
SS
SS
S
DOLB
Y PR
O LO
GIC g
x GA
ME
z1
SS
SS
S
DOLB
Y PR
O LO
GIC g
zz
3S
SS
SS
z1
If
Spe
aker
Con
g.
Sur
roun
d B
ack
is s
et t
o N
one
, thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
z2
If
Spe
aker
Con
g.
Sur
roun
d B
ack
is s
et t
o 1
spk
r o
r N
one
, thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
z3
If
Spe
aker
Con
g.
Fron
t H
eigh
t is
set
to
Non
e, t
his
surr
ound
mod
e ca
nnot
be
sele
cted
.z
4 Th
e sa
me
was
whe
n A
udys
sey
DS
X
se
ttin
g is
set
to
ON
.
z5
If
Spe
aker
Con
g.
Cen
ter
and
S
urro
und
is s
et t
o N
one
or
head
phon
es a
re u
sed,
thi
s su
rrou
nd m
ode
cann
ot
be s
elec
ted.
z
6 If
S
peak
er C
on g
.
Fr
ont
Hei
ght
, Fr
ont
Wid
e a
nd
Cen
ter
is s
et t
o N
one
or
head
phon
es a
re u
sed,
thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
-
34
Surro
und
mod
eN
OTE
Inpu
t sig
nal t
ypes
and
form
ats
ANAL
OGPC
M(m
ulti
ch)
PCM
(2ch
)
WM
A/M
P3/
MPE
G-4
AAC/
FLAC
/W
AV
DTS-
HDDT
SDO
LBY
DOLB
Y DI
GITA
LSu
per A
udio
CD
DTS-
HD
Mas
ter
Audi
o
DTS-
HD
High
Re
solu
tion
Audi
o
DTS
EXPR
ESS
DTS
ES
DSCR
T (W
ith F
lag)
DTS
ES
MTR
X (W
ith F
lag)
DTS
(5.1
ch)
DTS
96/2
4DO
LBY
True
HD
DOLB
Y DI
GITA
L Pl
us
DOLB
Y DI
GITA
L EX
(W
ith F
lag)
DOLB
Y DI
GITA
L EX
(W
ith n
o Fl
ag)
DOLB
Y DI
GITA
L (5
.1ch
)
DOLB
Y DI
GITA
L (2
ch)
DSD
(mul
ti ch
)DS
D(2
ch)
DOLB
Y SU
RROU
ND
DOLB
Y PR
O LO
GIC g
CIN
EMA
z5
SS
SS
S
DOLB
Y PR
O LO
GIC g
MUS
ICz
5S
SS
SS
DOLB
Y PR
O LO
GIC g
GAM
Ez
5S
SS
SS
DOLB
Y PR
O LO
GIC
z5
SS
SS
S
DOLB
Y PR
O LO
GIC g
CIN
EMA
A-DS
Xz
6S
SS
SS
DOLB
Y PR
O LO
GIC g
MUS
IC
A-DS
Xz
6S
SS
SS
DOLB
Y PR
O LO
GIC g
GAM
E A-
DSX
z6
SS
SS
S
DOLB
Y PR
O LO
GIC
A-DS
Xz
6S
SS
SS
Audy
ssey
DSX
z6
SS
SS
S
MUL
TI C
H IN
MUL
TI C
H IN
z4
FF
MUL
TI C
H IN
+ P
Lgx
CIN
EMA
z2z
4S
S
MUL
TI C
H IN
+ P
Lgx
MUS
ICz
1z4
SS
MUL
TI C
H IN
+ P
Lgz
z3
SS
MUL
TI C
H IN
+ D
olby
EX
z4
SS
MUL
TI C
H IN
7.1
z4
F D
(7
.1)
Audy
ssey
DSX
z6
SS
DIRE
CT DIRE
CTS
SS
SS
SS
SS
SS
SS
SS
SS
SS
DSD
DIRE
CTS
S
PURE
DIR
ECT
PURE
DIR
ECT
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
DSP
SIM
ULAT
ION
MUL
TI C
H ST
EREO
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
WID
E SC
REEN
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
SUPE
R ST
ADIU
MS
SS
SS
SS
SS
SS
SS
SS
SS
SS
ROCK
ARE
NA
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
JAZZ
CLU
BS
SS
SS
SS
SS
SS
SS
SS
SS
SS
CLAS
SIC
CON
CERT
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
MON
O M
OVIE
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
VIDE
O GA
ME
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
MAT
RIX
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
VIRT
UAL
SS
SS
SS
SS
SS
SS
SS
SS
SS
S
STER
EO STER
EOF
SF
FS
SS
SS
SS
SS
SS
SS
SF
z1
If
Spe
aker
Con
g.
Sur
roun
d B
ack
is s
et t
o N
one
, thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
z2
If
Spe
aker
Con
g.
Sur
roun
d B
ack
is s
et t
o 1
spk
r o
r N
one
, thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
z3
If
Spe
aker
Con
g.
Fron
t H
eigh
t is
set
to
Non
e, t
his
surr
ound
mod
e ca
nnot
be
sele
cted
.z
4 Th
e sa
me
was
whe
n A
udys
sey
DS
X
se
ttin
g is
set
to
ON
.z
5 If
S
peak
er C
on g
.
C
ente
r a
nd
Sur
roun
d is
set
to
Non
e o
r he
adph
ones
are
use
d, t
his
surr
ound
mod
e ca
nnot
be
sele
cted
. z
6 If
S
peak
er C
on g
.
Fr
ont
Hei
ght
, Fr
ont
Wid
e a
nd
Cen
ter
is s
et t
o N
one
or
head
phon
es a
re u
sed,
thi
s su
rrou
nd m
ode
cann
ot b
e se
lect
ed.
-
35
ADJUSTMENTAudio Section (8U-110093 Rch, 8U-110093A Lch)
Idling CurrentRequired measurement equipment: DC Voltmeter
1. Preparation(1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature
15 C ~ 30 C (59 F ~ 86 F).(2) Presetting
POWER (Power source switch) OFF(Do not connect power cord to AC line.)
SPEAKER (Speaker terminal) No load(Do not connect speaker, dummy resistor, etc.)
2. Adjustment(1) Remove top cover and set V101, V201, V301, V401 on 8U-110093A (Lch) at fully counterclockwise (c) position.(2) Set V201, V301, V401, V501, V601 on 8U-110093 (Rch) counterclockwise (c) position.(3) Connect DC Voltmeter to test points (8U-110093A Lch)
FRONT-Lch: N9010 q w pin SURROUND-Lch: N9010 e r pin SURROUND-BACK-Lch: N9010 t y pin FRONT HEIGHT/WIDE-Lch: N9013 q w pin
(4) Connect DC Voltmeter to test points (8U-110093 Rch) FRONT-Lch: N9013 t y pin CENTER ch: N9013 e r pin SURROUND-Rch: N9013 q w pin SURROUND-BACK-Rch: N9010 t y pin FRONT HEIGHT/WIDE-Rch: N9010 e r pin
(5) Connect power cord to AC Line, and turn power switch "ON".(6) Presetting.
MASTER VOLUME : "---" counterclockwise (c min.)MODE : VoluntaryFUNCTION : Voluntary
(7) Within 2 minutes, and turn V101 clockwise (x) to adjust the TEST POINT voltage to 6.5 mV 0.5 mV DC.
(8) After 10 minutes from preset, turn V101 to set the voltage to 8 mV 0.5 mV DC.(9) Adjust the Variable Resistors of other channels in the same way.(10) After 5 minutes from (7), turn V101 to set the voltage to 8 mV 0.5 mV DC.(11) Adjust the Variable Resistors of other channels in the same way.
8U-110093A Lch 8U-110093 Rch
V101
V201
V301
V401
V201
V301
V401
V501
V601
N9013
N9010
N9010
N9013
-
36
NO
NO
NO
NO
Is there damage in U102 (TOP258MG)?
Is there the damage in D100/D101/D102/D104/C102?
The solder short part of the PWB board is repaired.
Check the damage of each part.
The jumper wire is repaired.
Replace the parts of damage.
Replace the parts of damage.
Is the fuse (F1030) blown?
Is there solder short circuit in the PWB board?
Is there a damaged part?
Is disconnected jumper wire is connected to the PWB, do not touch?
Replace the U102(TOP258MG) and D100/D101/D102/D104.
DC 5V is not output.
YES
YES
YES
YES
YES
YES
YES
TROUBLE SHOOTING1. SMPS
-
37
2. Analog videoPerform the operation below beforehand.-b Check it whether connection cable and Monitor are normal.b VIDEO Convert is set to ON.b COMPONENT signal is set to 480i.b ZONE2 is set to POWER ON.b Function is set to DVR.
MONITOR OUT (CVBS) output NG
DVR MONITOR OUT(CVBS) output NG
COMPONENT OUT output NG
Z2 MONITOR OUT output NG
Input CVBS
Input CVBS
Input CVBS
Input CVBS
To A
To A
To A
To A
Input S
Input S
Input S
Input S
InputCOMPONENT
Input COMPONENT
Input COMPONENT
Input COMPONENT
Not output
Not output
b In this case, the function is set to BD.
-
38
InputCVBS,S,COMP
A
Check power supply voltage.SIDE CONNECT B'D N218
V+5V : 1,2pinV-5V : 5,6pin
Check signal detectionHDMI B'D N9002 V : 19pin H(+3.3V) S : 20pin H(+3.3V) COMPONENT : 18pin H(+3.3V)
Check the input signal to video decoder (HDMI B'D U1100). HDMI B'D V : R9015 S-Y : R9019 S-C : R9020 COMPONENT-Y : R90