www.liquasil.comwww.liquasil.com
Liquid Gutter Lining SystemFOR ASBESTOS, METAL AND CONCRETE GUTTERSLiquasil Limited
Unit 3 Radway Industrial Estate, Radway Road, Solihull, West Midlands B90 4NR
t 0121 709 5352 e [email protected] w www.liquasil.com
February 2019 - Version 4.0 Liquasil Limited - all rights reserved
TECHNICAL DATA SHEET
Asbestos and Metal Gutters SystemReference SWT Corrosion Primer Liquasil One
FOR PROFESSIONAL USE ONLY
Purpose/Uses Rust and wet tolerant for use Gutter Lining with Liquasil polymers
Colour Grey Standard Grey and RAL Colours Range subject to minimum quantities of 100 litres
Application Brush or Roller Apply by Brush - Roller
Volume Solids 100% 100%
Coverage Rate Up to 6m2 per litre. Presence of heavy rust or Approx 1.25 m2 per litre use on cast iron will reduce coverage rate
Thinners/Brush wash Use Sacrificial Brushes Xylene
Weight per Litre 2 kg (Supplied in 0.5 litre tins) 1 kg
Flash Point > 100º C Above 32º C
V.O.C. V.O.C. Free V.O.C. Free
Approvals ABS Certified, IMO Approval, Lloyds Approval BS 476: Part3:1958,
Ballast Tank Maintenance Coating Fire and BS 6920 Water Quality
Lloyds Type Approval: New Build Applications DIN EN ISO 7783-2
(Bore Steel and Shop Primers)
Finish Semi Gloss Semi Gloss
Drying Time Allow 6-24 hours drying time Rain free - 2 to 3 hours
Thoroughly dry- 16 hours
Surface Preparation Remove existing or factory finishes All surfaces must be clean and
and prepare to bare metal thoroughly dry, particularly at joints
Recommended Film Thickness 100 microns 750 microns
Application Temperature 5º C to 40º C (Optimum 15º C to 30º C) -5º C +60º C
Considerations Keep tins cool and shaded in summer. Keep tins warm in winter.
• Thoroughlycleanthegutter,removinganyexisting,unstablefinishesandprevious patch repairs (especially at joints) as far as reasonably practicable.
• If large holes, cracks or delamination of the asbestos cement substrate are present please contact Liquasil for further advice.
• TreatallmetalfixingswithLiquasilSWTPrimerandallowtodry.
• Before continuing, all surfaces to be coated must be bone dry. Ensure that there is no trapped moisture at the joints of the gutter.
• Apply a liberal coat of Liquasil Non-Sag Sealer to all previously treated metalfixingsandtoanysmallholesorcracksthatmightbepresent.
• Using a paint roller or brush, apply a single coat of Liquasil One at a wet filmthicknessof750microns.
• Thoroughly clean the gutter, removing any existing, unstable finishesandpreviouspatchrepairs(especiallyatjoints)asfarasreasonably practicable.
• ApplyasinglecoatofLiquasilSWTPrimeratawetfilmthicknessof 100 microns to entire surface to be treated and allow to dry. (SWT Primer can be applied to wet or damp surfaces).
• Before continuing, all surfaces to be coated must be bone dry. Ensure that there is no trapped moisture at the joints of the gutter.
• ApplyaliberalcoatofNon-SagSealertojointsandfixings.
• Using a paint roller or brush, apply a single coat of Liquasil One at awetfilmthicknessof750microns.
www.liquasil.comwww.liquasil.com
Before Sealer Completed InstallationPrimer
Application Method
Asbestos Cement Gutterseal SystemThoroughly clean gutter and allow to dry completely
Treat metal fixings with one coat of Liquasil Corrosion Treatment
Apply Liquasil Non-Sag Sealer to all joints, fixings, small holes and cracks
Brush apply Liquasil One to entire gutter to provide seamless gutter liner
www.liquasil.com
Cleaned, dry gutter Corrosion treatment to fixings Gaps, joints and fixings coated with Non-Sag Sealer
Finished seamless gutter lining
2
1
3
4
1 2 3
4
Liquasil Limited Unit 3 Radway Industrial Estate
Radway Road, Solihull, West Midlands B90 4NR
t 0121 709 5352 e [email protected] www.liquasil.com
Application Method
Asbestos Cement Gutterseal SystemThoroughly clean gutter and allow to dry completely
Treat metal fixings with one coat of Liquasil Corrosion Treatment
Apply Liquasil Non-Sag Sealer to all joints, fixings, small holes and cracks
Brush apply Liquasil One to entire gutter to provide seamless gutter liner
www.liquasil.com
Cleaned, dry gutter Corrosion treatment to fixings Gaps, joints and fixings coated with Non-Sag Sealer
Finished seamless gutter lining
2
1
3
4
1 2 3
4
Liquasil Limited Unit 3 Radway Industrial Estate
Radway Road, Solihull, West Midlands B90 4NR
t 0121 709 5352 e [email protected] www.liquasil.com
Application Method
Asbestos Cement Gutterseal SystemThoroughly clean gutter and allow to dry completely
Treat metal fixings with one coat of Liquasil Corrosion Treatment
Apply Liquasil Non-Sag Sealer to all joints, fixings, small holes and cracks
Brush apply Liquasil One to entire gutter to provide seamless gutter liner
www.liquasil.com
Cleaned, dry gutter Corrosion treatment to fixings Gaps, joints and fixings coated with Non-Sag Sealer
Finished seamless gutter lining
2
1
3
4
1 2 3
4
Liquasil Limited Unit 3 Radway Industrial Estate
Radway Road, Solihull, West Midlands B90 4NR
t 0121 709 5352 e [email protected] www.liquasil.com
Application Method
Asbestos Cement Gutterseal SystemThoroughly clean gutter and allow to dry completely
Treat metal fixings with one coat of Liquasil Corrosion Treatment
Apply Liquasil Non-Sag Sealer to all joints, fixings, small holes and cracks
Brush apply Liquasil One to entire gutter to provide seamless gutter liner
www.liquasil.com
Cleaned, dry gutter Corrosion treatment to fixings Gaps, joints and fixings coated with Non-Sag Sealer
Finished seamless gutter lining
2
1
3
4
1 2 3
4
Liquasil Limited Unit 3 Radway Industrial Estate
Radway Road, Solihull, West Midlands B90 4NR
t 0121 709 5352 e [email protected] www.liquasil.com
Application Method
Asbestos Cement or Concrete GuttersApplication Method
Metal Gutters
Before Completed InstallationPrimer Applied