Download - ARI Symbols
AHRI Standard 130 (formerly ARI 130)
2003 STANDARD for
GRAPHIC ELECTRICAL/ ELECTRONIC SYMBOLS FOR AIR-CONDITIONING AND REFRIGERATING EQUIPMENT
Price $10.00 (M) $20.00(NM) Copyright 2003, by Air-Conditioning, Heating, and Refrigeration Institute Printed in U.S.A. Registered United States Patent and Trademark Office
IMPORTANT
SAFETY DISCLAIMER AHRI does not set safety standards and does not certify or guarantee the safety of any products, components or systems designed, tested, rated, installed or operated in accordance with this standard/guideline. It is strongly recommended that products be designed, constructed, assembled, installed and operated in accordance with nationally recognized safety standards and code requirements appropriate for products covered by this standard/guideline. AHRI uses its best efforts to develop standards/guidelines employing state of the art and accepted industry practices. AHRI does not certify or guarantee that any tests conducted under its standards/guidelines will be non-hazardous or free from risk.
This standard supersedes ARI Standard 130-88.
TABLE OF CONTENTS
SECTION PAGE Section 1. Purpose ...................................................................................................................... 1 Section 2. Scope ......................................................................................................................... 1 Section 3. Definitions ................................................................................................................ 1 Section 4. Requirements .............................................................................................................. 1 Section 5. Fundamental Items .................................................................................................... 2 Section 6. Conductors, Connections and Connectors, and Connecting Devices ....................... 4 Section 7. Contacts, Switches, Contactors, Relays, Solenoids, and Switch Operating Devices .................................................................................. 6 Section 8. Transformers ........................................................................................................... 11 Section 9. Semiconductor Devices .......................................................................................... 12 Section 10. Motor Starters ......................................................................................................... 13 Section 11. Motor Starters ......................................................................................................... 15 Section 12. Lamps and Signaling Devices ................................................................................. 16 Section 13. Instruments .............................................................................................................. 17 Section 14. Rotating Machinery ............................................................................................... 17 Section 15. Conformance Conditions ........................................................................................ 19
FIGURES
Figure 1. Line Conventions for Diagrams ................................................................................ 2
APPENDICES
Appendix A. References - Normative ......................................................................................... 20 Appendix B. References – Informative ...................................................................................... 20
AHRI Standard 130 2003
1
GRAPHIC ELECTRICAL/ELECTRONIC SYMBOLS FOR AIR-CONDITIONING AND REFRIGERATING EQUIPMENT
Section 1. Purpose
1.1 Purpose. The purpose of this standard is to establish graphic symbols of commonly used electrical/electronic devices for air-conditioning and refrigerating equipment.
1.1.1 Intent. This standard is intended for the guidance of the industry, including manufacturers, engineers, installers, contractors and users.
1.2 Review and Amendment. This standard is subject to review and amendment as technology advances.
Section 2. Scope 2.1 Scope. This standard applies to all electrical/electronic devices, sub-assemblies and assemblies used within air-conditioning and refrigerating equipment. 2.2 Exclusions. This standard does not apply to all electrical/electronic devices, sub-assemblies and assemblies used within air-conditioning and refrigerating equipment.
Section 3. Definitions All terms in this document shall follow the standard industry definitions in the current edition of ASHRAE Terminology of Heating, Ventilation, Air Conditioning and Refrigeration unless otherwise defined in this section. 3.1 Electrical/Electronic Diagram (Diagram). A Diagram which takes the form of one or more of the types as defined below.
3.1.1 Connection Diagram (Writing Diagram). A diagram which shows the connections of an installation or its devices. It may cover internal or external connections, or both, and contains such detail as is needed to make or trace connections that are involved. The Connection Diagram usually shows general physical arrangement of the devices.
3.1.2 Interconnection Diagram. A Diagram which shows only external connections between assemblies or equipment. The internal connections of the assemblies or equipment are usually omitted.
3.1.3 Schematic Diagram (Elementary or Ladder Diagram). A Diagram which shows, by means of graphic symbols, the electrical connections and
functions of a specific circuit arrangement. The schematic diagram facilitates tracing the circuit and its functions without regard to the actual physical size, shape, or location of the device.
3.2 Graphic Symbols. Representations used to show the functioning or interconnections of a circuit. A graphic symbol represents the function of a device in the circuit, for example, when a resistor is employed as a fuse, the fuse symbol is used. Graphic Symbols are correlated with parts lists, descriptions, or instructions by means of designations. A symbol shall be considered as the aggregate of all its parts. If there is no suitable symbol listed in this standard, additional symbols from IEEE Standard 315, ANSI/IEEE 280, and IEC Standard Publications 60617 and 60027-1 may be used.
3.2.1 Applications. Applications where shown are examples of preferred combinations of symbols.
3.3 Reference Designation. A combination of letters and numbers used on diagrams to identify and refer to a device without regard to its function. For Reference Designation information, see ANSI/IEEE 200-1975.
3.4 "Shall" or "Should". "Shall" or "should" shall be
interpreted as follows:
3.4.1 Shall. Where "shall" or "shall not" is used for a provision specified, that provision is mandatory if compliance with the standard is claimed. 3.4.2 Should. "Should" is used to indicate provisions which are not mandatory but which are desirable as good practice.
Section 4. Requirements 4.1 General Requirements for Graphic Symbols. The following covers basic criteria which are applicable to all graphic symbols.
4.1.1 IEC Identification. In this standard, graphic symbols that have been recommended by the International Electrotechnical Commission (IEC) are indicated by IEC. Symbols indicated by IEC may have been constructed from two or more IEC symbol elements necessary to describe the specific application.
AHRI Standard 130 2003
2
4.1.2 Alternative Symbols. When alternative symbols are shown, the relative position of the symbols does not imply a preference; however, alternative symbols identified as IEC are recommended.
4.1.3 Applications. No attempt has been made to list all possible applications. Additional applications may be devised provided they reasonably and intelligibly make use of other symbols.
4.1.4 Orientation. Except where noted, the orientation of a symbol on a drawing, including a mirror-image presentation, does not alter the meaning of the symbol. Letters and numbers that constitute a part of a symbol shall not be presented in mirror-image form.
4.1.5 Line Convention.
4.1.5.1 Line thickness and lettering size shall take into account the diagram size and the reproduction process, when it is felt that legibility may be affected.
4.1.5.2 Solid lines shall represent factory wiring and dashed lines shall represent field wiring when both are shown on the same diagram (Figure 1). If additional line conventions are used, they shall be identified in the legend.
FACTORY WIRING FIELD WIRING
__________----------
Figure 1. Line Conventions For
Diagrams
4.1.6 Symbol Size. Graphic symbols shall be drawn to any proportional size that suits a particular diagram, provided the selection of sizes takes into account the anticipated reproduction process.
4.1.7 Addition of Supplementary Data. Details of type, impedance, rating, etc., may be added when required, adjacent to any symbol. If used, abbreviations should be from ANSI/ASME Y1.1. Letter combinations used as parts of graphic symbols are not abbreviations.
Section 5. Fundamental Items
5.1 Resistor.
5.1.1 Resistor, General.
IEC
or
IEC
5.1.2 Tapped Resistor.
IEC
or
IEC
5.1.3 Variable Resistor: with Adjustable Contact.
IEC
or
IEC
AHRI Standard 130 2003
3
5.1.4 Potentiometer.
IEC
or
IEC
5.1.5 Potentiometer, Preset.
IEC
or
IEC
5.1.6 Varistor (Voltage Dependent Resistor).
IEC
or
IEC
NOTE: V may be replaced by U.
5.1.7 Heater.
IEC
5.1.7.1 Application: Heater, Three Phase, Delta Connected.
IEC
5.2 Thermistor.
5.2.1 General.
IEC
5.2.1.1 Linear.
IEC
5.2.1.2 Non-Linear.
IEC
5.2.1.3 Positive Temp Coefficient.
IEC
5.2.1.4 Negative Temp Coefficient.
IEC
5.2.2 With Independent Integral Heater.
IEC
5.3 Capacitor.
5.3.1 General. If it is necessary to identify the capacitor electrodes, the curved element shall represent the outside electrode.
IEC
or
IEC
5.3.2 Polarized Capacitor.
IEC
5.3.3 Variable Capacitor.
IEC
AHRI Standard 130 2003
4
5.3.4 Feed Through Capacitor.
IEC
5.4 Battery. The long line is always positive.
IEC
5.4.1 Multicell. Symbol 5.4 may also be used to indicate a battery if there is no risk of confusion: otherwise, the voltage or the number and kind of cells should be indicated.
IEC
or
IEC
5.5 Sensing Link; Fusible Link, Ambient Temperature Operated.
IEC
5.6 Thermocouple (Dissimilar-Metals Device).
5.6.1 Temperature-Measuring Thermocouple.
IEC
5.7 Inductor.
5.7.1 Inductor Coil.
IEC
5.7.2 Inductor With Magnetic Core.
IEC
5.7.3 Ferrite Bead, Shown on a Conductor.
IEC
Section 6. Conductors, Connections and Connectors, and Connecting Devices
6.1 Conductor.
IEC
6.1.1 Shielded Single Conductor.
IEC
6.1.2 Conductors in a Cable Three-Conductor Shown.
IEC
6.1.3 Twisted Conductors, Two Conductors Shown.
IEC
or
IEC
6.1.4 Ribbon Cable.
IEC
n is not part of the symbol. It is the number of conductors that shall be indicated.
6.1.5 Application: Shielded Twisted Conductor Cable with Shield Grounded (Two-Conductor Shown).
IEC
6.2 Connections.
6.2.1 Junction (Connection).
IEC
AHRI Standard 130 2003
5
6.2.1.1 Application: Junction of Connected Paths, Conductors, or Wires.
IEC
or
IEC
6.2.2 Terminal.
IEC
6.2.3 Terminal Block.
IEC
6.3 Earth and Frame Connections.
6.3.1 Earth Ground. A direct conducting connection to the earth or body of water that is a part thereof.
IEC
6.3.2 Chassis Ground. A conducting connection.
IEC
6.3.3 Equipotentiality.
IEC
6.3.4 Protective Ground. This symbol may be used in place of 6.3.1, to indicate an earth connection having a specified protective function, for example, protection against electrical shock in case of a fault.
IEC
6.3.5 Noiseless Ground.
IEC
6.4 Connectors and Disconnecting Devices. The connection symbol is not an arrowhead. It is larger and the lines are drawn at a 90 ° angle.
6.4.1 Socket (Female).
IEC
or
IEC
6.4.2 Plug (Male).
IEC
or
IEC
6.4.3 Application: Plug and Socket.
IEC
6.4.3.1 Application: Multiple Plug and
Socket Shown with five Poles, Multi-Line Representation.
IEC
6.4.4 Connector Assembly, Fixed Portion.
IEC
Note: The symbol should be used only when it is desired to
distinguish between the fixed and free parts of the connection assembly.
6.4.5 Connector Assembly, Movable Portion.
IEC
AHRI Standard 130 2003
6
6.4.6 Application: Mated Connector Assembly. Example Shown with Plug Side Fixed and Socket Side Moveable.
IEC
6.4.6.1 Application: Mated Connector Assembly. Example Shown with Both Sides of Connector Moveable with Three Pins and Two Sockets in One Connector and Three Sockets and Two Pins in the Mating Connector.
IEC
6.4.7 Coaxial Plug and Socket.
IEC
6.5 Connecting Link.
6.5.1 Connecting Link, Closed.
IEC
6.5.2 Connecting Link, Open.
IEC
Section 7. Contacts, Switches, Contactors, Relays, Solenoids, and Switch Operating Devices 7.1 Switch Operating Devices. The following are qualifying symbols.
7.1.1 Manually Operated Control, General Case.
IEC
7.1.2 Operated by Pulling.
IEC
7.1.3 Operated by Turning.
IEC
7.1.4 Operated by Pushing.
IEC
7.1.5 Emergency Switch (Mushroom-Head Safety Feature).
IEC
7.1.6 Operated by Lever.
IEC
7.1.7 Operated by Key.
IEC
AHRI Standard 130 2003
7
7.1.8 Operated by Roller.
IEC
7.1.9 Operated by Cam.
IEC
7.1.10 Operated by Electric Motor.
IEC
7.1.11 Operated by Electric Clock.
IEC
7.2 Basic Contact and Switch Assemblies. Symbols for contacts and mechanical connections may be used for switch symbols. For switches that may be in any of two or more positions with no operating force applied, a clarifying note may be necessary to explain the point at which the switch functions. The standard method of illustrating a contact is by a symbol indicating the circuit condition it produces when the actuating device is in the de-energized or non-operated position. The actuating device may be of a mechanical, electrical, or other nature, and a clarifying note may be necessary with the symbol to explain the proper point at which the contact functions; for example, the point where a contact closes or opens as a function of a changing quantity, e.g., pressure, level, flow, voltage, current. In cases where it is desirable to illustrate contacts in the energized or operated condition and where confusion may result, a clarifying note shall be added to the drawing.
7.2.1 Normally Closed Contact (Break).
or
IEC
7.2.2 Normally Open Contact (Make).
or
IEC
7.2.3 Change-Over Break Before Make Contact.
IEC
7.2.4 Two-Way Contact with Center Off Position.
IEC
7.2.5 Change-Over Make Before Break Contact.
IEC
7.2.6 Normally Open Contact with Time-Delay Closing (NOTC). (Make Contact Delayed when Closing.)
or
IEC
7.2.7 Normally Closed Contact with Time-Delay Opening (NCTO). (Break Contact Delayed when Opening)
or
IEC
7.2.8 Normally Open Contact with Time-Delay Opening (NOTO).(Make Contact Delayed when Reopening.)
or
IEC
AHRI Standard 130 2003
8
7.2.9 Normally Closed Contact with Time-Delay Closing (NCTC). (Break Contact Delayed when Reclosing)
or
IEC
7.3 Operating Device (General Symbol).
or
IEC
7.3.1 Relay Coil of an Alternating Current Relay.
IEC
7.3.2 Relay Coil of a Direct Current Relay. Relays that are direct current operated are not marked to indicate DC operation. Use the general symbol of 6.3 above.
7.3.3 Relay Coil of a Slow-Releasing Relay.
IEC
7.3.4 Relay Coil of a Slow-Operating Relay.
IEC
7.3.5 Relay Coil of a Slow-Operating and Slow-Releasing Relay.
IEC
7.3.6 Actuating Device of a Thermal Relay.
IEC
7.3.7 Relay Coil of a Slow Releasing Alternating Current Relay.
IEC
7.4 Electromagnetic Actuator (Solenoid) with Mechanical Linkage Shown.
IEC
7.5 Manually Operated Switch.
7.5.1 Maintained.
7.5.1.1 Switch, Single Throw.
or
7.5.1.1.1 Application: Three-Pole Disconnect Switch. Lever Operated Isolating (Not to be Opened Under Load)
IEC
7.5.1.1.2 Application Three-Pole Disconnect Switch. Lever Operated (May be Opened Under Load)
IEC
or
AHRI Standard 130 2003
9
7.5.1.2 Switch, Double Throw.
or
IEC
7.5.1.3 Switch, 3 Position with Center Off.
or
IEC
7.5.1.4 Two Circuit, Maintained or Not Spring-Return.
or
IEC
7.5.2 Pushbutton, Momentary or Spring-Return.
7.5.2.1 Normally Open, Circuit Closing (Make).
or
IEC
7.5.2.2 Normally Closed, Circuit Opening (Break).
or
IEC
7.5.2.3 Two Circuit (Dual).
or
IEC
7.5.3 Examples of Multi-Pole and Multi-Position Switches.
7.5.3.1 Single-Pole N-Position Switch. Show for n = 6.
IEC
7.5.3.2 Single-Pole n-Position Switch. Alternatives for Use when n is small. Shown for n = 4.
IEC
or
IEC
7.5.3.3 Four-Position Switch. Manually Operated, Having Four Independent Circuits.
IEC
AHRI Standard 130 2003
10
7.5.3.4 Single-Pole, Four-Position Switch in which Position 2 Cannot be Connected.
IEC
7.5.3.5 Single-Pole, Six-Position Switch with a Wiper that Bridges only while Passing from one Position to the Next.
IEC
7.5.3.6 Single-Pole, Multi-Position Switch with a Wiper that Bridges Three Consecutive Terminals in Each Switch Position.
IEC
7.5.3.7 Single-Pole, Multi-Position Switch with a Wiper that Bridges Four Terminals but One Intermediate Terminal in Each Switch Position.
IEC
7.6 Limit Switch, Directly Actuated, Spring Returned.
7.6.1 Limit Switch Normally Open.
or
IEC
7.6.2 Limit Switch Normally Closed.
or
IEC
7.7 Flow Actuated Switch.
7.7.1 Closes on Increase in Flow.
or
IEC
7.7.2 Opens on Increase in Flow.
or
IEC
7.8 Liquid-Level-Actuated Switch.
7.8.1 Closes on Rising Level.
or
IEC
7.8.2 Opens on Rising Level.
or
IEC
AHRI Standard 130 2003
11
7.9 Pressure- or Vacuum-Actuated Switch. 7.9.1 Closes on Rising Pressure.
or
IEC
7.9.2 Opens on Rising Pressure.
or
IEC
7.9.3 Closes on Rising Differential Pressure.
or
IEC
7.9.4 Opens on Rising Differential Pressure.
or
IEC
7.10 Temperature-Actuated Switch.
7.10.1 Closes on Rising Temperature.
or
IEC
7.10.2 Opens on Rising Temperature.
or
IEC
7.11 Humidity-Actuated Switch.
7.11.1 Closes on Rising Humidity.
or
IEC
7.11.2 Opens on Rising Humidity.
or
IEC
Section 8. Transformers 8.1 Transformer with Multiple Windings.
8.1.1 Transformer with Two Windings.
IEC
AHRI Standard 130 2003
12
8.1.2 Transformer with Two Windings, Shown with Instantaneous Voltage Polarity Indicators.
IEC
8.1.3 Transformer with Three Windings.
IEC
8.1.4 Transformer with Center Tap on One Winding.
IEC
8.1.5 Transformer with Variable Coupling.
IEC
8.2 Auto-Transformer.
8.2.1 Auto-Transformer.
IEC
8.2.2 Adjustable Auto-Transformer.
IEC
8.3 Current Transformer.
IEC
Section 9. Semiconductor Devices 9.1 Two Terminal Devices.
9.1.1 Semiconductor Diode, Semiconductor Rectifier Diode.
or
IEC
9.1.2 Unidirectional Diode, Voltage Regulator, Zener Diode.
or
IEC
9.1.3 Breakdown Diode, Bi-Directional.
or
IEC
9.1.4 Photodiode.
or
IEC
9.1.5 Light Emitting Diode.
or
IEC
9.1.6 Diode, Temperature Dependent.
IEC
AHRI Standard 130 2003
13
9.1.7 Bi-directional Diode, Diac.
IEC
9.2 Three (or More) Terminal Devices.
9.2.1 Thyristor, Type Unspecified.
IEC
9.2.2 Thyristor, Reverse Blocking Triode-Type, N-Type Gate, Semiconductor Controlled Rectifier, N-Type Gate.
or
IEC
9.2.3 Thyristor, Reverse Blocking Triode-Type, P-Type Gate, Semiconductor Controlled Rectifier, P-Type Gate.
or
IEC
9.2.4 Thyristor, Reverse Blocking Tetrode-Type, Semiconductor Controlled Switch.
or
IEC
9.2.5 Thyristor, Bi-directional Triode-Type, Triac, Gated Switch.
or
IEC
9.2.6 PNP Transistor.
IEC
9.2.7 NPN Transistor.
IEC
9.2.8 NPN Transistor with Collector Connected to the Envelope.
IEC
9.2.9 Optical Coupling Device: Opto Isolator Shown with Light Emitting Diode and Phototransistor.
IEC
Section 10. Circuit Protectors 10.1 Fuse.
IEC
or
or
AHRI Standard 130 2003
14
10.2 Circuit Operators.
10.2.1 Thermal Operator.
or
or
IEC
10.2.2 Magnetic Operator.
or
IEC
10.3 Circuit Breaker.
10.3.1 General.
IEC
or
10.3.1.1 Single-Pole Circuit Breaker with Thermal Overload.
IEC
or
or
10.3.1.2 Single-Pole Circuit Breaker with Magnetic Overload.
or
IEC
10.3.2 Three-Pole Circuit Breaker with Thermal Overload Device in All 3 Poles.
or
or
IEC
10.3.3 Three-Pole Circuit Breaker with Magnetic Overload Device in All 3 Poles.
or
AHRI Standard 130 2003
15
IEC
10.3.4 Three-Pole Circuit Breaker with Thermal and Magnetic Overload Devices in All 3 Poles.
or
IEC
10.4 Gaps and Arrestors.
10.4.1 Gap.
or
IEC
10.4.2 Double Spark Gap.
IEC
10.4.3 Protective Gas Discharge Tube.
IEC
Section 11. Motor Starters 11.1 General.
IEC
11.1.1 Application. Motor Starter with Three Thermal Current Elements and a Setting Range From 5 to 6 Amperes.
IEC
11.1.2 Application. Motor Starter with Three Magnetic Current Elements and a Setting Range from 5 to 7 amperes.
IEC
11.1.3 Application. Motor starter With Three Thermal Magnetic Current Elements and a Setting Range from 2 to 5 amperes.
IEC
11.2 Star-Delta (Wye-Delta) Starter.
IEC
11.3 Auto-Transfer Starter.
IEC
11.4 Primary Reactor Starter.
IEC
AHRI Standard 130 2003
16
11.5 Starter Regulator With Thyristors.
IEC
Section 12. Lamps and Signaling Devices 12.1 Lamp, General Symbol.
IEC
Notes: If it is desired to indicate color, a notation according to the following code is placed adjacent to the symbol.
Color IEC ANSI Y1.1
Red RD RED
Yellow YE YEL
Green GN GRN
Blue BU BLU
White WH WHT
Amber AM AMB
Orange OR ORN
Purple PR PRP
Clear CLR
If it is desired to indicate the type of lamp, a notation according to the following code is placed adjacent to the symbol: Ne = neon Xe = xenon Na = sodium vapor Hg = mercury I = iodine IN = incandescent EL = electroluminescent ARC = arc FL = fluorescent IR = infra-red UV = ultra-violet LED = light emitting diode
12.1.1 Application, Red Neon Lamp.
IEC*
12.1.2 Signal Lamp, Flashing Type.
IEC
12.2 Signaling Devices.
12.2.1 Horn.
IEC
12.2.2 Bell.
IEC
or
IEC
12.2.3 Single-Stroke Bell.�
IEC
12.2.4 Siren.
IEC
12.2.5 Buzzer.
IEC
or
IEC
12.2.6 Whistle, Electrically Operated.
IEC
AHRI Standard 130 2003
17
Section 13. Instruments
13.1 Indicating Instruments.
IEC
The asterisk within the symbols of this section shall be replaced with one of the following:
V = Voltmeter A = Ammeter W = Wattmeter Hz = Frequency Meter = Oscilloscope to = Temperature � = Tachometer
13.2 Recording Instruments.
IEC
The asterisk within the symbols of this section shall be replaced with one of the following:
to = Temperature % H2O = Humidity V = Voltmeter A = Ammeter
13.3 Integrating Instruments.
IEC
The asterisk within the symbols of this section shall be replaced with one of the following:
h = Hour Meter Wh = Watt-hour Meter
13.4 Pulse Meter (Electrically-Operated Counting Device).
IEC
Section 14. Rotating Machinery 14.1 Rotating Machine.
14.1.1 Motor, General
IEC
14.1.2 Generator, General.
IEC
14.1.3 Stepping Motor, General.
IEC
14.1.4 D.C. Two-Wire Series Motor.
IEC
14.1.5 D.C. Two-Wire Shunt Motor.
IEC
14.1.6 D.C. Two-Wire Generator, Compound Excited, Short Shunt, Shown with Terminals and Brushes.
IEC
14.1.7 Induction Motor, Single-Phase (General).
IEC
14.1.7.1 Induction Motor, Single Phase, Squirrel Cage, Leads of Split Phase Brought Out.
IEC
AHRI Standard 130 2003
18
14.1.7.2 Induction Motor, Single-Phase, with One Lead of Split Phase Connected Internally.
IEC
or
IEC
14.1.7.3 Induction Motor, Single-Phase, with One Phase Connected Internally and Internal Thermal Protection.
or
14.1.8 Induction Motor, Three-Phase, Squirrel Cage (General).
IEC
14.1.8.1 Induction Motor, Three-Phase, Wye Connected.
IEC
14.1.8.2 Induction Motor, Three-Phase, Delta Connected.
IEC
14.1.8.3 Induction Motor, Three Phase with Both Leads of Each Phase Winding Brought Out.
IEC
14.1.8.4 Induction Motor, Three Phase with Two Delta Connected Windings.
IEC
14.1.8.5 Induction Motor, Three Phase, Dual Voltage.
14.1.8.6 Induction Motor, Three-Phase with Internal Thermal Overload Protection.
14.1.9 Induction Motor, Reversible, Squirrel Cage with Two Phase Winding, Four Wire.
AHRI Standard 130 2003
19
Section 15. Conformance Conditions 15.1 Conformance. While conformance with this standard is voluntary, symbols represented as being in accordance with this standard shall conform with all the provisions thereof.
AHRI Standard 130 2003
20
APPENDIX A. REFERENCES – NORMATIVE A1 Listed here are all standards, handbooks, and other publications essential to the formation and implementation of the standard. All references in this appendix are considered as part of this standard.
A1.1 ANSI/ASME Standard Y1.1-1989, Abbreviations for Use on Drawings and in Text, 1989, American National Standards Institute/American Society of Mechanical Engineers25 West 43rd Street, 4th Floor, New York, NY 10036, U.S.A /345 East 47th Street, New York, NY 10017, U.S.A
A1.2 ANSI/IEEE Standard 280-1985 (R1997), Letter Symbols for Quantities Used in Electrical Science and Engineering, 1997, 25 West 43rd Street, 4th Floor, New York, NY 10036, U.S.A/345 East 47th Street, New York, NY 10017, U.S.A A1.3 ANSI/IEEE Standard 200-1975 (R1988), Reference Designations for Electrical and Electronic, 1988, 25 West 43rd Street, 4th Floor, New York, NY 10036, U.S.A/345 East 47th Street, New York, NY 10017, U.S.A
A1.4 ANSI/IEEE Standard 315-1975 (R1994), Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Class
Designation Letters), 1994, 25 West 43rd Street, 4th Floor, New York, NY 10036, U.S.A/345 East 47th Street, New York, NY 10017, U.S.A A1.5 ASHRAE Terminology of Heating, Ventilation, Air Conditioning and Refrigeration, Second Edition, 1991, American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., 1791 Tullie Circle N.E., Atlanta, GA 30329, U.S.A. A1.6 IEC Standard Publication 60027-1, Letter Symbols to be Used in Electrical Technology - Part1, 1992, International Electrotechnical Commission, 3, rue de Varembe, P.O. Box 131, 1211 Geneva 20, Switzerland. A1.7 IEC Standard Publication 60617-1, Graphical Symbols for Diagrams, 1985, International Electrotechnical Commission, 3, rue de Varembe, P.O. Box 131, 1211 Geneva 20, Switzerland.
A1.8 AHRI Standard 110-2002 (formerly ARI Standard 110-2002), Air-Conditioning and Refrigerating Equipment Nameplate Voltages, 2002, Air-Conditioning, Heating, and Refrigeration Institute, 2111 Wilson Boulevard, Suite 500, , Arlington, VA 22201, U.S.A.
APPENDIX B. REFERENCES – INFORMATIVE
None.