Download - AMRL Preliminary Report
-
8/13/2019 AMRL Preliminary Report
1/15
AMRL Preliminary Report QS - 1
Quality System Evaluation
Name of Lab: __________________________________________________ Assessment No. ___________
Location (City, State): _________________________________________________
Table of Contents
SECTION PAGE " " IF OK
A. Quality System Criteria (AASHTO R18)1. Quality Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Technical Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. Quality System Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4. Equipment Calibration and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5. Proficiency Sample Testing and Records . . . . . . . . . . . . . . . . . . . . . . . . 1
6. Test Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
7. Records Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
8. Training and Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Quality Manual Requirements (AASHTO R18)
1. Organization and Organizational Policies . . . . . . . . . . . . . . . . . . . . . . . 3
2. Staff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4
3. Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Test Records and Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Sample Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Diagnostic and Corrective Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Internal Quality System Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
8. Subcontracting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C. Additional Requirements - ASTM D3666 (Bituminous) . . . . . . . . . . . . . . . . . . . . 6
D. Additional Requirements - ASTM D3740 (Soil) . . . . . . . . . . . . . . . . . . . . . . . . . . 7
NOTE : An "X" indicates that a deficiency exists for one or more of the items listed under that heading.
-
8/13/2019 AMRL Preliminary Report
2/15
AMRL Preliminary Report QS - 1
Scope of Quality System Review: Indicate the fields of test included in the scope of this quality system evaluation.(Note - A quality system evaluation should be conducted in all fields associated with the laboratory's on-site assessment.)
AC EML HMA SOL AGG
A. QUALITY SYSTEM CRITERIA (AASHTO R18)
1. Quality Manual (QM) (Section 5.1) :(a) Does the CML maintain a quality manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (b) Does each document in the QM indicate its preparation or revision date? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (c) Is the QM available for use by laboratory staff? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
2. Technical Manager (Section 5.2) :(a) Does the CML have a technical manager who has overall responsibility for technical operations of lab? . . . . . . ____
Name: ____________________________ Title: ___________________________ (b) Has the CML nominated an individual to serve in the technical manager's absence? . . . . . . . . . . . . . . . . . . . . . ____
Name: ____________________________ Title: ___________________________
3. Quality System Management (Section 5.3) :(a) Does the CML have a person(s) responsible for determining if quality system implementation activities are
being conducted according to the QM? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Name(s): __________________________ Title(s): _________________________ (b) Does this individual have access to top management? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (c) Does the CML's management review the quality system at least annually? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (d) When a technical complaint casts doubt on the quality of the CML's work, does the CML's management
ensure the quality system's continuing stability and effectiveness, and introduce any necessarychanges or improvements? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
4. Equipment Calibration and Verification Criteria (Sections 5.4 and 5.8):(a) Is equipment that has been removed from service and new equipment that has been shown by verification
(or otherwise) to be defective taken out of service and clearly identified? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (b) Is newly acquired test equipment and materials without manufacturers certification calibrated or verified
before being placed in service? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (c) Are all applicable calibration and verification records and procedures adequate (see tables)? . . . . . . . . . . . . . ____
5. Proficiency Sample Testing and Records (Sections 5.5 and 5.10):All laboratories (regardless of accreditation status):(a) Is the laboratory currently enrolled in all AMRL proficiency sample programs applicable to the scope of this
assessment? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (b) Has the laboratory participated (i.e. supplied data) in all AMRL proficiency sample programs applicable to the
scope of this assessment, and tested both samples in each pair, since the previous on-site assessment (seetables)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(c) Does the laboratory retain copies of all corrective action letters from final proficiency sample reports forwhich the laboratory received low ratings (i.e., 0, 1 or 2)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Accredited laboratories only:(d) Did the laboratory perform all proficiency sample test methods for which the laboratory is accredited? . . . . . . . . ____
Note to Assessors: Check the laboratorys ratings sheets in their copies of the most recent final proficiency samplereport(s) for each applicable material (i.e. hot-mix, soil, etc.).
(e) Has AMRL received a corrective action letter from the laboratory within 60 days of the issuance of any final
-
8/13/2019 AMRL Preliminary Report
3/15
AMRL Preliminary Report QS - 2
6. Test Records (Section 5.6) :(a) Does the CML maintain test records for tests covered in the scope of the associated on-site assessment? . . ____ (b) Do the test records contain sufficient information to permit verification of any test reports (original
observations, calculations, derived data and identification of personnel involved in sampling and testing)? . . . ____ (c) Are existing reports clearly referenced whenever they are amended? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (d) Does the CML prepare test reports which clearly present the following information (Table 6):
(1) Identification of the report and the date issued? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Description, identification and condition of the test sample? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Test results and other pertinent data required by the standard test method? . . . . . . . . . . . . . . . . . . . . ____ (4) The name of the person(s) accepting technical responsibility for the test report? . . . . . . . . . . . . . . . . . ____ (5) An identification of any test results obtained from tests performed by subcontractor (if applicable)? . . ____
(e) Is following information included on test reports or included in test records and traceable to test reports(Table 6):(1) The name and address of the testing laboratory? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(2) Name and address of the client or identification of the project? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Date of receipt of the test sample? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Date(s) of test performance? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (5) Identification of standard test method used & notation of all known deviations from test method? . . . . ____
7. Records Retention (Section 5.7)* :(a) Does the CML retain the following records for a minimum of 3 years*:
(1) Records pertaining to testing (work sheets, original observations/calculations, ID of testing tech., etc.)? ____ (2) Records pertaining to equipment calibration and verification? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Test reports? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Records pertaining to internal quality system reviews (Ref. R18 Section 6.7)? . . . . . . . . . . . . . . . . . . . ____
Note to Assessors: All labs must present completed IQSRs, regardless of accreditation status.(5) Records pertaining to proficiency sample testing (Sections 5.5 and 5.10)? . . . . . . . . . . . . . . . . . . . . . ____ (6) Records pertaining to technician training and evaluation? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (7) Personnel records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
* Note to Assessors - Ask lab to show records to verify 3 year record maintenance.
8. Training and Evaluation (Section 5.9)*:(a) Has the CML trained all new technicians employed since last assessment, who are performing tests covered
by scope of associated on-site assessment, in manner described in QM? . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(b) Has the CML evaluated the competency of all technicians performing tests covered by scope of associatedon-site assessment in manner described in QM? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Note to Assessors: All labs must present completed training and/or competency evaluation records, regardless ofaccreditation status.
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
4/15
AMRL Preliminary Report QS - 3
B. QUALITY MANUAL (QM) REQUIREMENTS (AASHTO R18)
Does the laboratory's Quality Manual contain the following documents:
1. Organization and Organizational Policies (Section 6.1) :(a) Legal name and address of CML - and that of main office or company, if different - and any other
information needed to identify the organization (6.1.1)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (b) Ownership and management structure of the CML including names, affiliations and positions of principal
officers and directors (6.1.2)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (c) Organization chart showing relevant internal organizational components (6.1.3)? . . . . . . . . . . . . . . . . . . . . . . . ____
2. Staff (Section 6.2) :(a) Outline or chart showing operational personnel positions and their lines of authority and responsibility? . . . . . ____
Position Descriptions (6.2.2) :(b) Position descriptions for each technical operational position shown on CML's organization chart? . . . . . . . . . . . ____
Note: A reference to where position descriptions are found is acceptable if they are not in the QM.
Do the position descriptions:(1) Identify the position? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Describe the duties associated with the position? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Describe the required skills, education and experience? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Indicate the supervision exercised and received? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Biographical Sketches (6.2.3) :(c) Brief biographical sketches for supervisory technical staff involved in testing areas covered by scope of quality system evaluation? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ Note: A reference to where biographical sketches are found is acceptable if they are not in the QM.
Do the biographical sketches indicate the following for each individual:(1) Education and work experience? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Licensure and certifications? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Current position? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Training and Competency Evaluations (6.2.4 and 6.2.5) :(d) Method(s) used to ensure that CML personnel are trained to perform tests covered by scope of quality
system evaluation (6.2.4)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Does the document:(1) Indicate what position(s) or employee(s) is responsible for the training program and maintenance
of records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Describe distribution of records to management? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Identify location of resulting records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(e) Method(s) used to evaluate staff competency to ensure that each test covered by scope of quality system
evaluation is performed in accordance with standard procedures (6.2.5)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Does the document:(1) Indicate the frequency of evaluations? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Indicate what position(s) or employee(s) is responsible for evaluating staff competency and
maintaining records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Describe distribution of records to management? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Identify location of resulting records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
-
8/13/2019 AMRL Preliminary Report
5/15
AMRL Preliminary Report QS - 4
(f) Sample form(s) used to record results of training and competency evaluation activities (6.2.6)? . . . . . . . . . . . ____
Does the form:(1) Include a field for entering name of trainee? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Include a field for entering name of evaluator? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Indicate test method(s) evaluated? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Include field for indicating date activities took place? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (5) Provide field for recording results of training or evaluation activity? . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
3. Equipment (Section 6.3) :Inventory (6.3.1) :
(a) Inventory of major sampling, testing, calibration and verification equipment associated with test methodscovered by scope of quality system evaluation, and a copy of the manufacturer's instructions whereapplicable? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Note: A reference to where the inventory and the manufacturer's instructions are found is acceptable ifthey are not in the QM.
Does the inventory include, for each piece of major equipment where available:(1) Name of equipment? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Date received? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Date placed in service? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Condition when received? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (5) Manufacturer? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (6) Model and serial number (or other acceptable identification number)? . . . . . . . . . . . . . . . . . . . . . . . . . ____
Equipment Calibration & Verification (6.3.2) :(b) List(s) giving general description of equipment for performing tests covered by scope of quality system
evaluation which require calibration or verification (6.3.2.1)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Does the information for each item listed include:(1) Interval of calibration or verification? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Reference to calibration or verification procedure used? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Location of calibration and verification records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(c) CML's method for ensuring that calibration and verification procedures are performed for all requiredequipment at specified intervals (6.3.2.2)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Does the document:(1) Indicate name(s) of individual(s) responsible for ensuring that calibration and verification
activities are carried out? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Describe procedures for handling equipment which is newly acquired, removed from service, out of
calibration or defective? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Identify individual(s) responsible for maintaining equipment calibration and verification records? . . . . . . ____ (4) Describe distribution of equipment calibration and verification records to management? . . . . . . . . . . . . ____ (5) Identify location of resulting records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(d) In-house equipment calibration and verification procedures, when they cannot be referenced in applicablestandards, or has reference to their location in the CML (6.3.2.3)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(e) Certificates or other documents that establish traceability of in-house equipment or reference standardsused for calibration and verification, if any (6.3.2.4)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ Note: A reference to where certificates are found is acceptable if they are not in the QM.
-
8/13/2019 AMRL Preliminary Report
6/15
AMRL Preliminary Report QS - 5
4. Test Records and Reports (Section 6.4) :(a) Methods used by CML to produce test records and to prepare, check and amend test reports (6.4.1)? . . . . . . ____
Does the document:(1) Identify individual(s) responsible for maintaining test records and reports? . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Describe distribution of test reports to management? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Identify location of resulting records? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(b) Typical test report forms which illustrate manner in which tests results and supporting information(Section 5.6) are documented (6.4.2)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
5. Sample Management (Section 6.5) :(a) Procedure(s) for sample identification, storage, retention, and disposal? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
6. Diagnostic and Corrective Action (Section 6.6) :(a) Description of participation in proficiency sample and on-site assessment programs (6.6.1)? . . . . . . . . . . . . . ____
Does the document(s) describe:(1) Methods used to identify poor results? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Procedures followed when poor results and deficiencies occur? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
(b) Method(s) used in responding to external technical complaints (6.6.2)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
7. Internal Quality System Review (Section 6.7):
(a) Scope of internal quality system reviews? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
Does the document:(1) Indicate frequency of reviews? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Identify individual responsible for conducting reviews? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (3) Describe distribution of reports to management? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ (4) Indicate location of records showing results of reviews? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
8. Subcontracting (Section 6.8) :
(a) Policies which CML follows relative to subcontracting or a statement that the CML does not engage insuch activities? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ Note: A reference to where the policies are found is acceptable if they are not in the QM.
Does the document include:(1) Procedures followed by the CML in selecting competent subcontractors? . . . . . . . . . . . . . . . . . . . . . . . . ____ (2) Procedures followed by the CML when reporting results of testing performed by subcontractors? . . . . . ____
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
7/15
AMRL Preliminary Report QS - 6
C. ADDITIONAL REQUIREMENTS - ASTM D3666 (Bituminous)
Note : These are requirements, in addition to what is required by AASHTO R18,that the lab must meet in order to become accredited for ASTM D3666.
D3666 - Minimum Requirements for Agencies Testing and Inspecting Bituminous Paving Materials
1. Does the Laboratory Manager have at least 5 years experience in inspecting and testing bituminous materialsand construction (Section 7.1) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
2. Does the Supervising Laboratory Technician have at least 5 years experience performing testing on bituminousmaterials (Section 7.2) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
3. Does the Supervising Field or Plant Technician or Inspector have at least 5 years experience in inspecting the kindof work involved in the bituminous construction project (Section 7.3) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____ 1Note : AASHTO does not review personnel qualification records for compliance to certification requirements.
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
8/15
AMRL Preliminary Report QS - 7
D. ADDITIONAL REQUIREMENTS - ASTM D3740 (Soil)
Note : These are requirements, in addition to what is required by AASHTO R18,that the lab must meet in order to become accredited for ASTM D3740.
D3740 - Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soiland Rock as Used in Engineering Design and Construction
1. Does the Laboratory Manager have at least 5 years experience in the inspection and testing of soil and rock(Section 7.1) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
2. Does the Supervising Laboratory Technician have at least 5 years experience performing testing on soil androck (Section 7.2) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
3. Does the Supervising Field Technician have at least 5 years experience in inspecting the kind of work involved inthe soil and rock construction project (Section 7.3) 1? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
1Note : AASHTO does not review personnel qualification records for compliance to certification requirements.
4. Are the Supervising Laboratory Technician and Supervising Field Technician re-evaluated at least every three years for each test the person is authorized to perform (Sections 7.2 and 7.3)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
5. Are Inspecting or Testing Technicians re-evaluated at least every two years for each test the person is authorized toperform (Section 7.4)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
6. Does the agency have a laboratory procedure manual outlining the method or inspection procedure for eachcustomary test or service performed by the laboratory (Section 8.1.3)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
7. Does the agency maintain records of any external audits and documentation describing how the deficiencies werecorrected (Section 8.1.8)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
8. Does the QM contain a list showing applicable dates of the qualifications, accreditations and recognition of theagency by others (Section 9.1.1.4)? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ____
9. Does the agency maintain records of the verification of competency of any external organizations used (Section 11.2.6)?____
Note to Assessors: This would include outside agencies that are used for equipment c/v as well as subcontractor laboratories.
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
9/15
AMRL Preliminary Report April 2000
1Other information which uniquely identifies the test equipment may be substituted.2Example: Serial No. of proving ring, std. thermometer, st d. weight set, calipers, balances, timers, std. oil, etc.3This information does not have to appear on the C/V record.4A standard calibration or verification procedure is available and in most cases must be used.5List of all equipment, including glass plates, rulers, straightedges, etc.
Date: ___________ Assessment No.: ___________
Assessor: ___________
Bituminous Materials Test Equipment
ITEM R18Spec. Int.
(mo.)
Cal/Verif (C/V) Written Procedures Do the records contain the following?
Labspec.
interval< R18?
C/Vwithinspec.int.?
In QMor ref.
to loc.?
5C/VEquip.listed
1Model &Serial No.
Nameof
worker
2ID of C/V
equipused
Datework done
3 Nextduedate
3PreviousC/Vdate
Detailedresults
Referenceto
procedureused
ASPHALT
Flash cups (check critical dimensions) (T48/D92) 12
Flash cups (check critical dimensions) (T79/D3143) 12
Penetrometers (T49/D5) (check accuracy of dial & timer, check needle condition) 6
Collars and floats (check critical dimensions) (T50/D139) 12
Ductility machines (T51/D113) (check molds & speed of travel) 12
Brass rings and assemblies (check critical dimensions) (T53/D36) 12
Thin-Film ovens (T179/D1754) (check rotation speed of shelf, check temperature) 12
Timers (check accuracy) (T201/D2170, T202/D2171) 6
Pycnometers (check cri tical dimensions & physical condition) (T228/D70) 12
Rolling Thin-Film ovens (T240/D2872) (check rotation speed of shelf, check temperature) 12
Flow meters (calibrate) (T240/D2872) 12
EMULSION
Saybolt viscometers (calibrate) (T59/D244) 36 4 4 T72/D88
GENERAL EQUIPMENT
Ovens (verify temperature settings) 4
Thermometers (calibrate)(T49/D5, T51/D113, T201/D2170, T202/D2171, T209/D2041, T228/D70, T295/D3142)
6 4 4 E77
General purpose balances, scales, and weights (verify) 12
Analytical balances and weights (verify) 24
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
10/15
AMRL Preliminary Report April 2000
1Other information which uniquely identifies the test equipment may be substituted.2Example: Serial No. of proving ring, std. thermometer, st d. weight set, calipers, balances, timers, std. oil, etc.3This information does not have to appear on the C/V record.4A standard calibration or verification procedure is available and in most cases must be used.5List of all equipment, including glass plates, rulers, straightedges, etc.
Date: ___________ Assessment No.: ___________
Assessor: ___________
Hot-Mix Asphalt (HMA) Test Equipment
ITEM R18Spec.
Int.(mo.)
Cal/Verif (C/V) WrittenProcedures
Do the records contain the following?
Labspec.
interval< R18?
C/Vwithin
spec.int.?
In QM
or ref.to loc.?
5C/V
Equip.listed
1Model
& Serial No.
Name
of worker
2ID of C/V
equipused
Date
work done
3 Next
duedate
3Previous
C/Vdate Detailedresults
Referenceto
procedureused
Mechanical compactors (calibrate) (T245) 36
Manual compaction hammers (T245/D1559) (check mass of hammer & critical dimensions) 12
Molds (check critical dimensions) (T245/D1559) 12
Breaking heads (check critical dimensions) (T245/D1559) 12
California kneading compactors (calibrate) (T247/D1561) 24
Calibration cylinders (check critical dimensions) (T246/D1560) 12
Molds (check critical dimensions) (T247/D1561) 12
Followers ( check critical dimensions) (T246/D1560, T247/D1561) 12
Compression testing machines (T167/D1074, T245/D1559, T246/D1560) (verify load indications) 12
4 4 T67/E4
Compressive strength molds (check critical dimensions) (T167/D1074) 12
Compressive strength plungers (check critical dimensions) (T167/D1074) 12
Flow meters (calibrate) (T170/D1856) 12Vacuum system (check pressure) (T209/D2041) 12
Mechanical shakers (check sieving thoroughness) (T30/D5444) 12 4 4 T30/D5444
Sieves (check physical condition of all, check openings of No.4) (T30/D5444) 6 4 4 M92/E11
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
11/15
AMRL Preliminary Report April 2000
1Other information which uniquely identifies the test equipment may be substituted.2Example: Serial No. of proving ring, std. thermometer, st d. weight set, calipers, balances, timers, std. oil, etc.3This information does not have to appear on the C/V record.4A standard calibration or verification procedure is available and in most cases must be used.5List of all equipment, including glass plates, rulers, straightedges, etc.
Date: ___________ Assessment No.: ___________
Assessor: ___________
Soil Test Equipment
ITEM R18Spec.
Int.(mo.)
Cal/Verif (C/V) WrittenProcedures
Do the records contain the following?
Labspec.
interval< R18?
C/Vwithin
spec.int.?
In QM
or ref.to loc.?
5C/V
Equip.used
1Model
& Serial No.
Name
of worker
2ID of C/V
equipused
Date
work done
3 Next
duedate
3Previous
C/Vdate Detailedresults
Referenceto
procedureused
Hydrometers (check critical dimensions) (T88/D422) 24
Liquid limit devices (check wear & critical dimensions) (T89/D4318) 12
Grooving tools (check critical dimensions) (T89/D4318) 12
Mechanical compactors (calibrate- 5.5 lb ) (T99/D698) 12 4 4 D2168
Mechanical compactors (calibrate - 10 lb ) (T180/D1557) 12 4
Manual hammers (check weight & critical dimensions - 5.5 lb ) (T99/D698) 12Manual hammers (check weight & critical dimensions - 10 lb ) (T180/D1557) 12
Molds: proctor & soil cements (T99/D698, T134/D558, T135/D559, T136/D560, T180/D1557)(check critical dimensions, 4-in. diameter) 12
Molds: proctor (check critical dimensions, 6-in. diameter) (T99/D698, T180/D1557) 12
Molds: R-value (check critical dimensions) (T190/D2844) 12
Molds: CBR (check critical dimensions) (T193/D1883) 12
Straightedges (T99/D698, T134/D558, T135/D559, T136/D560,
T180/D1557)(check planeness of edge) 6
Vacuum systems (check pressure) (T100/D854) 24
Weighted foot assemblies (check weight) (T176/D2419) 12
Soil Test Equipment Continued On Next PageCOMMENTS:
-
8/13/2019 AMRL Preliminary Report
12/15
AMRL Preliminary Report April 2000
1Other information which uniquely identifies the test equipment may be substituted.2Example: Serial No. of proving ring, std. thermometer, st d. weight set, calipers, balances, timers, std. oil, etc.3This information does not have to appear on the C/V record.4A standard calibration or verification procedure is available and in most cases must be used.5List of all equipment, including glass plates, rulers, straightedges, etc.
Date: ___________ Assessment No.: ___________
Assessor: ___________
Soil Test Equipment (contd)
ITEM R18Spec.
Int.(mo.)
Cal/Verif (C/V) WrittenProcedures
Do the records contain the following?
Labspec.
interval< R18?
C/Vwithin
spec.int.?
In QM
or ref.to loc.?
5C/V
Equip.used
1Model
& Serial No.
Name
of worker
2ID of C/V
equipused
Date
work done
3 Next
duedate
3Previous
C/Vdate Detailedresults
Referenceto
procedureused
California kneading compactor (calibrate) (T190/D2844) 24
Standard metal specimens (check outside diameter) (T190/D2844) 12
Metal followers (check diameter) (T190/D2844) 12
CBR annular and slotted weights (check weight) (T193/D1883) 12
CBR penetration pistons (check diameter) (T193/D1883) 12
Compression/ loading devices: CBR (verify load indications) (T193/D1883) 12
4 4 T67/E4
Compression/ loading devices: unconf. (verify load indications) (T208/D2166) 12 4 4 T67/E4
Compression/ loading devices: consol. (verify load indications) (T216/D2435) 12
Compression/ loading devices: shear (verify normal load indication) (T236/D3080) 12
Compression/ loading devices: shear (verify shear load indications) (T236/D3080) 12 4 4 T67/E4
Compression/ loading devices: UU (veri fy load indica tions) (T296/D2850) 12 4 4 T67/E4
Compression/ loading devices: CU (veri fy load indica tions) (T297/D4767) 12 4 4 T67/E4
Mechanical shakers (check sieving thoroughness) 124 4 T27/C136
Sieves (check physical condition of all, check openings of No. 4) 6 4 4 M92/E11
Ovens (verify temperature settings) 4
General purpose balances, scales, and weights (verify) 12
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
13/15
AMRL Preliminary Report April 2000
1Other information which uniquely identifies the test equipment may be substituted.2Example: Serial No. of proving ring, std. thermometer, st d. weight set, calipers, balances, timers, std. oil, etc.3This information does not have to appear on the C/V record.4A standard calibration or verification procedure is available and in most cases must be used.5List of all equipment, including glass plates, rulers, straightedges, etc.
Date: ___________ Assessment No.: ___________
Assessor: ___________
Aggregate Test Equipment
ITEM R18Spec. Int.
(mo.)
Cal/Verif (C/V) WrittenProcedures
Do the records contain the following?
Labspec.
interval< R18?
C/Vwithinspec.int.?
In QMor ref.
to loc.?
5C/VEquip.listed
1Model& Serial
No.
Nameof
worker
2ID of C/V
equipused
Datework done
3 Nextduedate
3PreviousC/Vdate
Detailedresults
Referenceto
procedureused
Unit weight measures (calibrate) (T19/C29) 12 4 4 T19/C29
Conical molds and tampers (check critical dimensions) (T84/C128) 24
L.A. machines (check RPM & critical dimensions) (T96/C131) 24
Steel balls (check individual weight & charge weight) (T96/C131) 24
Sulfate soundness specimen containers (check physical condition) (T104/C88) 12
Sulfate soundness oven (check rate of evaporation) (T104/C88) 12 4 4 T104/C88
Weighted foot assemblies (check weight) (T176/D2419) 12
Mechanical shakers (check sieving thoroughness) 12 4 4 T27/C136
Sieves (check physical condition of all, check openings of No. 4) 6 4 4 M92/E11
Ovens (verify temperature settings) 4
General purpose balances, scales, and weights (verify) 12
COMMENTS:
-
8/13/2019 AMRL Preliminary Report
14/15
-
8/13/2019 AMRL Preliminary Report
15/15
AMRL Preliminary Report April 2000
Date: ___________ Assessment No.: ___________
Assessor: ___________
Proficiency Sample Program (PSP) Requirements
Laboratory Name/Location: __________________________________________ AMRL #: ____________ Date of Previous OSA: ____________
Areas Accredited/Dates: _______/_______ _______/_______ _______/_______ _______/_______
Types of Samples Applicable tothe Laboratorys Accreditation
SampleNumber(s)Received
Date of Final
Report
DataProvidedto AMRL?
List any test methods in the scope of thelaboratorys accreditation for which low
ratings or insufficient data were received.
CorrectiveAction Provided
to AMRL?
CorrectiveAction Retainedby Laboratory?
COMMENTS: