![Page 1: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/1.jpg)
AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS Scot Waye, Matthew Musselman, Charlie King National Renewable Energy Laboratory 2014 Thermal Management Systems Symposium September 22–24, 2014 Denver, Colorado 14TMSS-0022
NREL/PR-5400-62920
![Page 2: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/2.jpg)
SAE INTERNATIONAL
Project Objective
2
• Enable air-cooling thermal management of automotive power electronics, with a focus on high-temperature devices
o Design, optimize, build, and demonstrate an air-cooled inverter
o Compare to conventional cooling systems: thermal resistance, coefficient-of-performance, volume, weight
Motivation
• Help industry achieve the DOE APEEM 2015 30-kW (55-kW peak) inverter targets (12 kW/L, 12 kW/kg) through improved thermal management
• Provide pathways to meeting 2020 targets (13.4 kW/L, 14.1 kW/kg)
Cost
Power Density, Specific Power, Efficiency
![Page 3: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/3.jpg)
SAE INTERNATIONAL
Project Perspective
3
All vehicles are air cooled
Air cooling a goal for batteries: • Simple • Direct
Just indirectly
Jim Snyder, NREL Image Gallery 15165
![Page 4: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/4.jpg)
SAE INTERNATIONAL
State of the Art
4
LS 600H 2008
Camry 2007
Indirect Air Cooling via Liquid Cooling
Intermediate liquid cooling loop rejects heat to air
Direct Air Cooling
Has been done before
Honda Insight (12 kW)
AC Propulsion (150 kW)
Mitsubishi SiC Inverter (50 kVA/L, 400 V output, 156 kVA)
SiC = Silicon Carbide
Low Power
Low Power Density
Prototype: not in vehicle
NREL: John Rugh
Courtesy ORNL
DOE Advanced Vehicle Testing Activity (Idaho National Laboratory)
![Page 5: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/5.jpg)
SAE INTERNATIONAL
Air as a Coolant
5
• Air is a poor heat-transfer fluid (low specific heat, density, conductivity) • Large volume of air is needed • Large surface area increases heat transfer, but increases volume • Potential parasitic power of fan • Not yet used in production vehicles • Filtering, fouling, fan noise
Challenges
Advantages • Rejecting heat directly to air can eliminate intermediate liquid-air loops • Attractive for high-temperature device (wide-bandgap) applications • Air can be used to cool other components (e.g., capacitors) • Air is benign, is not carried, and does not need to be replaced • Air is a dielectric and can contact the chip directly • No global warming potential • No liquid leaks
![Page 6: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/6.jpg)
SAE INTERNATIONAL
System-Level Analysis
6
![Page 7: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/7.jpg)
SAE INTERNATIONAL
High-Temperature Air-Cooled Inverter
7
• Electrical Design: Device type and location; electrical duty cycles; temperature-dependent losses, efficiency
• Thermal Constraints: Maximum junction temperature; heat generation; coolant temperature
• Feasibility / Trade-Off: Modeling; extrapolate to inverter scale
• Thermal Design: Sub-module testing and model validation; fan/ducting testing; optimization
• Thermal System Design: Balance-of-system analysis; full system models
• Hardware: Module prototype, improve design; balance-of-system testing
Thermal Constraints
Thermal System Design
Thermal Design
Feasibility / Trade-Off
Hardware
Elec
tric
al D
esig
n (O
RNL)
Design
Prototype Development
Validation
![Page 8: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/8.jpg)
SAE INTERNATIONAL
Module Optimization to Inverter Level Characterization
8
1Casing volume adjusted for fin geometry 1Capacitor ~1.13 La, ~1.62 kga 1Gate driver + control board ~0.88 La, ~0.42 kgb
aAssumption provided by ORNL; bNREL assumption based on similar device measurement
Heat dissipation for 55-kW peak power From conservative analytical analysis ~ 2.7 kW heat (95% efficient)
• Fixed device heat generation and temperature (175ºC) • Parametrically optimized geometry by varying air flow
rate using computational fluid dynamics (CFD) – ANSYS Fluent
• Extrapolated sub-module modeling and testing results to module level
• Added in balance-of-inverter components1
Baseline
Optimized
Capacitor Capacitor
2 devices
9 modules 6 modules
![Page 9: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/9.jpg)
SAE INTERNATIONAL
Module Design Improvement (Parametric CFD)
9
Parametrically Changed: • Device Location • Fin Height • Fin Length • Base Plate Thickness • Fin Thickness • Channel Width
Improved weight and fan power
Improved volume and fan power
Modeling
![Page 10: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/10.jpg)
SAE INTERNATIONAL
Optimized Geometries Improve Specific Power
10
Baseline Optimized
Decreasing length
Increasing height
Changes to channel height and length
nine modules, DBC (direct-bond-copper)
Modeling
![Page 11: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/11.jpg)
SAE INTERNATIONAL
Balance of System: Ducting
11
Example Production Vehicle Air Ducts
Production Duct 1 Production Duct 2
Volkswagen Touareg Toyota Highlander Toyota Camry Toyota Prius Nissan Altima Hyundai Sonata Chevy Volt
Inverter Location
Surrogate ducting pressure curves
Experimental
![Page 12: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/12.jpg)
SAE INTERNATIONAL
Specific Power versus Parasitic Power for Various Heat Exchanger Geometries (Nine Modules)
12
Baseline
2015 Target
2020 Target
Power draw comparison AC blower AC condenser fan
Peak
Steady state
Low parasitic power but hard to meet targets
Modeling
nine modules, DBC (direct-bond-copper)
![Page 13: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/13.jpg)
SAE INTERNATIONAL
Specific Power versus Parasitic Power for Various Heat Exchanger Geometries (Six Modules)
13
2015 Target
2020 Target
Power draw comparison AC Blower AC Condenser fan
Peak
Steady-state
Meeting targets with acceptable parasitic power
Decreasing height
Increasing length
Modeling
six modules, DBC (direct-bond-copper)
![Page 14: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/14.jpg)
SAE INTERNATIONAL
Power Density versus Parasitic Power for Various Heat Exchanger Geometries (Six Modules)
14
2015 Target
2020 Target
Power draw comparison AC Blower AC Condenser fan
Peak
Steady-state
Meeting targets with acceptable parasitic power
Decreasing height
Increasing length
Modeling
nine modules, DBA (direct-bond-aluminum
![Page 15: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/15.jpg)
SAE INTERNATIONAL
System-Level Test Bench
15
• Meets fan test standard o ANSI/AMCA 210-07 o ANSI/ASHRAE 51-07
• Range: 5–500 cfm • U95 Flow: ±1.5 cfm • U95 Pressure: ±1.6 Pa
Fan pressure curves Fan efficiency curves
Fan or duct test subject
Blower
Experimental
![Page 16: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/16.jpg)
SAE INTERNATIONAL
Example System Flow Study
16
Fan operation 45 – 70 W Heat
Pressure
2) Heat dissipation: 3.2 kW, exceeds 2.7 kW target
Example fan
3) Maximum flow rate: 115 cfm
1) Cross point of the fan curve and pressure loss
![Page 17: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/17.jpg)
SAE INTERNATIONAL
Sub-Module Heat Exchanger Experiments
17
devices
Heaters 2.7-kW heat dissipation
target for inverter
Baseline
Optimized
Prototypes provided by Sapa Extrusions USA (wire EDM)
Channel height – 15 mm Channel length – 74 mm
Channel height – 21 mm Channel length – 40 mm
ceramic heater Indium foil copper (with thermocouple) thermal epoxy
aluminum heat exchanger
Experimental
![Page 18: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/18.jpg)
SAE INTERNATIONAL
Heat Dissipation for Baseline Case (Nine Modules)
18
Specific Power*: 8.9 kW/kg Power Density*: 10.1 kW/L
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 19: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/19.jpg)
SAE INTERNATIONAL
Heat Dissipation for Baseline Case (Nine Modules)
19
~ 60 cfm 5 W Fluid Power
Heat dissipation: 2.7 kW target
Tout ~ 100ºC
Specific Power*: 8.9 kW/kg Power Density*: 10.1 kW/L
Fan sized to satisfy flow rate and pressure drop
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 20: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/20.jpg)
SAE INTERNATIONAL 20
Heat Dissipation for Optimized Case (Six Modules)
Specific Power*: 14.3 kW/kg Power Density*: 14.5 kW/L
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 21: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/21.jpg)
SAE INTERNATIONAL 21
Heat Dissipation for Optimized Case (Six Modules)
Specific Power*: 14.3 kW/kg Power Density*: 14.5 kW/L
~235 cfm 180 W Fluid Power
Heat dissipation: 2.7 kW target
Specific power and power density meet 2020 targets, with tradeoff of higher parasitic power
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 22: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/22.jpg)
SAE INTERNATIONAL 22
Heat Dissipation for Optimized Case (Six Modules)
Specific Power*: 14.3 kW/kg Power Density*: 14.5 kW/L
Heat dissipation: 2.7 kW target
Specific power and power density meet 2020 targets, with tradeoff of higher parasitic power
~135 cfm 40 W Fluid Power
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 23: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/23.jpg)
SAE INTERNATIONAL 23
Heat Dissipation for Optimized Case (Six Modules)
Specific Power*: 14.3 kW/kg Power Density*: 14.5 kW/L
Heat dissipation: 2.7 kW target
Specific power and power density meet 2020 targets, with tradeoff of higher parasitic power
~50 cfm 4 W Fluid Power
Tout ~ 120ºC
*does not include inverter casing Extrapolated to inverter scale
Experimental
![Page 24: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/24.jpg)
SAE INTERNATIONAL
Inlet Temperature Effect (175ºC Junction Temperature)
24
Experimental
![Page 25: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/25.jpg)
SAE INTERNATIONAL
Fluid Power for Various Junction Temperatures
25
Experimental
![Page 26: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/26.jpg)
SAE INTERNATIONAL
Inlet versus Outlet Temperature at Various Junction Temperatures
26
Experimental
![Page 27: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/27.jpg)
SAE INTERNATIONAL
Module-Level Heat Exchanger Testing
ceramic resistance heaters
Experimental
27
![Page 28: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/28.jpg)
SAE INTERNATIONAL
Heat Dissipation of Module-Scale Heat Exchanger Experimental
Not extrapolated to inverter scale
28
![Page 29: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/29.jpg)
SAE INTERNATIONAL
Heat Dissipation of Module-Scale Heat Exchanger
Flat curves show low sensitivity to flow rate (reaching asymptote)
Experimental
Not extrapolated to inverter scale
29
![Page 30: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/30.jpg)
SAE INTERNATIONAL
Inlet and Outlet Temperatures of Module-Scale Heat Exchanger Experimental
Not extrapolated to inverter scale
Outlet temperatures reasonable
30
![Page 31: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/31.jpg)
SAE INTERNATIONAL
Summary
31
• Good potential technology for low cost, simple-to-manufacture options for high-temperature devices
• Eliminates liquid-to-air coolant loop • Provides potential solution to cooling components with lower
temperature limits (e.g., 85°C capacitor)
• Thermal performance for baseline and optimized sub-modules was characterized
• 10-kW module heat exchanger characterization and performance completed
• Parasitic power acceptable (in line with other vehicle components [e.g., A/C fan or condenser])
![Page 32: AIR COOLING FOR HIGH TEMPERATURE POWER ELECTRONICS · 2015. 1. 7. · o ANSI/AMCA 210- 07 o ANSI/ASHRAE 51- 07 • Range: 5–500 cfm • U 95 Flow: ±1.5 cfm • U 95 Pressure: ±1.6](https://reader035.vdocuments.us/reader035/viewer/2022062509/60fcc0d374c2a529241ec1ed/html5/thumbnails/32.jpg)
SAE INTERNATIONAL
Conclusions
32
• Reducing the number of modules (with penalty of increased heat generation from increased current and increased parasitic power) is beneficial for weight and volume considerations
• Further optimization to thermal and electrical solutions would further reduce weight and volume
• Balance of inverter component design and optimization vital to meeting targets
• More advanced heat exchanger designs may improve heat transfer efficiency with tradeoffs in manufacturability and cost
• Electrical and thermal aspects need co-design to meet targets