Advanced RFIC Design ELEN359A, Lecture 3: Gilbert
Cell MixersInstructor: Dr. Allen A Sweet
Copy Right 2004
All of Design is the Art and Science of Navigating Tradeoffs
• Science gives us the tools to understand what nature, in the form of the laws of physics, will allow us to do and not to do.
• Tradeoffs are the points where we as designers must make decisions.
• The Art of design is the process by which we make good decisions given numerous factors such as economics, market acceptance, cost of development, competitive pressures, etc.
Copy Right 2004
Basic Non Linear Process Produces Mixer Action
• Active Device Non Linearity is Expressed as a Power Series relating the device’s Voltage and Current: I(t) = I0 + k1V + k2V*2 + k3V*3 + …
• If V = V1 + V2 (two input signals), the second order term becomes: k2(V1*2 + V1V2 + V2*2). It is the V1V2 product term that produces mixing action because if V1 and V2 are sin waves, their produce, (v1cosW1t)x(v2cosW2t) = (v1v2/2)[cos(W1-W2)t + cos(W1+W2)t] contain the sum and difference mixing Frequencies.
Copy Right 2004
Down Converting Mixer: Applications to Receivers
FI=Fl-Fr
Copy Right 2004
Up Converting Mixer: Applications To Transmitters
FR=Fl+/-FIUSBLSB
Copy Right 2004
Double Balanced Diode Mixer Topology
L VirtualGround
R VirtualGround
Copy Right 2004
Diode IV Characteristics
Copy Right 2004
VBIC Diode IV
Copy Right 2004
ADS Schematic of a Balanced 4 Diode Mixer
Copy Right 2004
HB Controller, Gain Equation and RF Source
Copy Right 2004
LO Source
Copy Right 2004
HB Controller
Copy Right 2004
HB Controller to Sweep RF_pwr
Copy Right 2004
Conversion Loss vs RF_pwr
Gain CompressionBegins
Copy Right 2004
HB Controller to Sweep LO_pwr
Copy Right 2004
HB Controller to Sweep LO_pwr
Copy Right 2004
Conversion Loss vs LO_pwr
(LO Amp Requires100 mA Current @30 % efficiency)
(Preamp Requires20 mA Current to Boost Gain to +10 dB)
Copy Right 2004
Single Balance Bipolar Transistor Multiplying Mixer Topology
Vi = Vl x Vr
Q1 collector currentControls Transconductance
Copy Right 2004
Advantages of a Single Balanced Bipolar Transistor Multiplier
• High Conversion Gain (5 to 10 dB)• High L to R Isolation (but not high L to I
Isolation).• Low LO power Requirement (-10 to 0
dBm).• IIP3 is higher than the LO power level. • Low DC Power, Small size
Copy Right 2004
Double Balanced (Gilbert Cell) Bipolar Transistor Mixer
Copy Right 2004
Advantages of a Gilbert Cell Transistor Mixer
• All Three ports are differential, which is a natural configuration for creating Quadrature Phase Modulators and Detectors.
• L to R, L to I Isolations are excellent. • All the Advantages of the Single Balanced
Transistor Mixer are available in this case.
Copy Right 2004
A Direct Conversion Receiver using Gilbert Cell Mixers
Copy Right 2004
Gilbert Cell Mixer Topology
Copy Right 2004
Fully Differential Mixer Cell
Copy Right 2004
Series Diode Bias Tree
Copy Right 2004
DC Power and Output Term
Copy Right 2004
RF and LO Sources
Copy Right 2004
HB Controller and Equations
Copy Right 2004
Harmonic Balance Controller
Copy Right 2004
DC Analysis
Copy Right 2004
Bias Tree DC Levels
Copy Right 2004
MIX Function Determines Frequency Index
Copy Right 2004
Basic Simulation Calculates Conversion Gain in Two Ways
Copy Right 2004
LPF Eliminates Spurious Signals in the Mixer’s Output
Copy Right 2004
Mixer Simulation including an Output LPF.
Copy Right 2004
HB Controller to Sweep LO_pwr
Copy Right 2004
HB Controller to Sweep LO_pwr
Copy Right 2004
Simulation of Gain vs LO_pwr
Copy Right 2004
HB Controller for Sweeping RF_pwr
Copy Right 2004
HB Controller to Sweep RF_pwr
Copy Right 2004
Simulated Gain vs RF_pwr
(P-1dB)
Copy Right 2004
S Parameter Controller Simulates Isolations and Matches
Copy Right 2004
Matches and Isolations of a Gilbert Cell Mixer
Copy Right 2004
Disabling one Transistor Creates Imbalance and Poor Isolation
Copy Right 2004
Gilbert Cell Up Converter
(i.e. F2+/-F1)
Copy Right 2004
Up Converting Mixer HB Controller and Equations
Copy Right 2004
Sources for Up Converting Mixer
Copy Right 2004
BPF Selects a USB or an LSB Output
Copy Right 2004
Up Converter Simulation Including MIX Function Table
Copy Right 2004
USB Output is Selected with the BPF
Copy Right 2004
HB Controller and Equations to Simulate OIP3
Copy Right 2004
LO and RF Sources for Intermodulation Simulations
Copy Right 2004
HB Controller-Freq
Copy Right 2004
HB Controller-Sweep
Copy Right 2004
HB Controller- Solver
Copy Right 2004
HB Controller- Params
Copy Right 2004
MIX Function Determines Frequency Index for each Signal
Copy Right 2004
Intermodulation Spectrum
Copy Right 2004
Gain and OIP3(upper and lower) vs LO_pwr
(dBm)
(dB)
Copy Right 2004
LO and RF Sources to Simulate Non Linear Noise Figure
Copy Right 2004
HB Controller and Equations for Noise Figure Simulation
Copy Right 2004
HB Controller-Freq
Copy Right 2004
HB Controller-Params
Copy Right 2004
HB Controller- Noise(1)
Copy Right 2004
HB Controller-Noise (2)
Copy Right 2004
HB Controller-Solver
Copy Right 2004
HB Controller- Output
Copy Right 2004
Simulated ssb Noise Figure
Copy Right 2004
Simulated Noise Figure (dsb) and Conv Gain
Copy Right 2004
Noise Voltage Output at 400 MHz in a 1 Hz Bandwidth
Copy Right 2004
Home Work #2:A Down Converting Mixer for Wi-Fi
Copy Right 2004
• Design a Down Converting Gilbert Cell Mixer for 802.11B (RF_freq=2400 MHz). This mixer will down convert received Wi-Fi signals to an IF frequency of 850 MHz where a cellular/PCS receiver will process them. Conversion gain is to be at least 10 dB. As part of the design, an integral HPF (designed per lecture 2) in front of the mixer will reduce PCS interference at 1800 MHz by at least 20 dB.
• LO_pwr=-10 dBm, Vcc=+5.0 volts, Ic=10 mA max. All transformers are off chip.
Home Work #3: Advanced Wi-Fi Mixer
• Simulate the three isolations, the three matches, P-1dB compressed power, upper and lower OIP3, and the large signal noise figure for the mixer you designed in home work #2.
• Layout your Wi-Fi mixer using Knowledge On design rules. All three radio frequency ports (RF, LO, and IF) are to be pairs of standard bonding pads, spaced by 150 microns (c-c) which can be bonded to three off chip transformers. A 7th pad is Vcc. Keep your layout as “square” as possible.
Copy Right 2004