Series 31 Size NG18 ((A)A10VSO) Size NG28 to 140 (A10VO)Nominal pressure 4000 psi (280 bar)Maximum pressure 5100 psi (350 bar)Open circuit
FeaturesVariable pump in axial piston swashplate design for hydrosta- –tic drives in an open circuit
The flow is proportional to the drive speed and the displace- –ment.
The flow can be steplessly varied by adjustment of the –swashplate angle.
2 case drain ports –
Excellent suction characteristics –
Low noise level –
Long service life –
Favorable power/weight ratio –
Versatile controller range –
Short control time –
The through drive is suitable for adding gear pumps and axial –piston pumps up to the same size, i.e., 100% through drive.
RA-A 92701/03.12 1/52Replaces: 12.09Axial Piston Variable Pump
A10V(S)O (US-Version)
Data sheet Position Foto (oben links):X = 153Y = 93,9
ContentsType code for standard program 2
Technical data 4
DG – Two-point control, directly operated 10
DR – Pressure control 11
DRG – Pressure control, remotely operated 12
DFR/DFR1 – Pressure and flow control 13
DFLR – Pressure, flow and power control 14
ED – Electro-hydraulic pressure control 15
ER – Electro-hydraulic pressure control 16
Dimensions size 18 to 140 18
Dimensions through drive 42
Summary mounting options 45
Combination pumps A10VO + A10VO 46
Connector for solenoids 47
Installation instructions 48
General instructions 52
(A)A10V(S)O Series 31 RA-A 92701/03.122/52 Bosch Rexroth Corp.
Type code for standard program
O / 31 – V01 02 03 04 05 06 07 08 09 10 11 12 13
Version 18 28 45 71 100 140
01Standard version (without symbol) l l l l l l
High-speed version – – l l l l H
Axial piston unit
02Swashplate design, variable, nominal pressure 4000 psi (280 bar), maximum pressure 5100 psi (350 bar)
l – – – – – A10VS
– l l l l l A10V
Operation mode03 Pump, open circuit O
Size (NG)04 Geometric displacement, see table of values on pages 6 and 7 18 28 45 71 100 140
Control device
05
Two-point control, directly operated l l l l l l DG
Pressure control l l l l l l DR
with flow control, hydraulic
X-T open l l l l l l DFR
X-T closed l l l l l l DFR1
with flow and differential pressure control, electrically variable m l l l l – EF1)
with pressure cut-off, remotely operated
hydraulic l l l l l l DRG
electrical negative characteristic 12V l l l l l l ED71
24V l l l l l l ED72
positive characteristic 12V l l l l l l ER712)
24V l l l l l l ER722)
Pressure, flow and power control – l l l l l DFLR
Series06 Series 3, Index 1 31
Direction of rotation
07Viewed on drive shaft clockwise R
counter clockwise L
Seals08 FKM (fluor-caoutchouc) V
= available m = on request – = not available
See RE 927091)
The following must be taken into account during project planning: 2)
Excessive current levels (I > 1200 mA with 12 V or I > 600 mA with 24 V) to the ER solenoid can result in undesired increase of pressure which can lead to pump or system damage: - Use Imax current limiter solenoids. - A sandwich plate pressure reducing valve can be used to protect the pump in the event of overflow. An accessory kit with sandwich plate pressure reducing valve can be ordered from Rexroth under part number R902490825.
3/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Type code for standard program
O / 31 – V01 02 03 04 05 06 07 08 09 10 11 12 13
Drive shaft 18 28 45 71 100 140
09
Splined shaft ANSI B92.1a
standard shaft l l l l l l S
similar to shaft "S" however for higher input torque l l l l – – R
reduced diameter, not for through drive l l l l l m U
same as "U", higher torque; not for through drive – l l l l m W
Mounting flange 18 28 45 71 100 140
10ISO 3019-1 (SAE) 2-hole l l l l l l C
4-hole – – – – – l D
Service line port 18 28 45 71 100 140
11
SAE flange ports at rear, UNC fastening thread, not for through drive – l l – l l 61
– – – l – – 91
SAE flange ports on opposite side, UNC fastening thread l l l – l l 62
– – – l – – 92
Through drive 18 28 45 71 100 140
12
without through drive l l l l l l N00
Flange ISO 3019-1 (SAE) coupling for splined shaft1)
Diameter diameter
82-2 (A) 5/8 in 9T 16/32DP l l l l l l K01
3/4 in 11T 16/32DP l l l l l l K52
101-2 (B) 7/8 in 13T 16/32DP – l l l l l K68
1 in 15T 16/32DP – – l l l l K04127-2 (C) 1 1/4 in 14T 12/24DP – – – l l l K07
1 1/2 in 17T 12/24DP – – – – l l K24152-4 (D) 1 3/4 in 13T 8/16DP – – – – – l K17
Connectors for solenoids2) 18 28 45 71 100 14013 DEUTSCH - molded connector, 2-pin – without suppressor diode l l l l l l P
Coupling for splined shaft as per ANSI B92.1a1)
Connectors for other electric components can deviate.2)
= available m = on request – = not available
(A)A10V(S)O Series 31 RA-A 92701/03.124/52 Bosch Rexroth Corp.
Technical dataHydraulic fluid
Before starting project planning, please refer to our data sheets RE 90220 (mineral oil), RE 90221 (environmentally acceptable hydraulic fluids) and RE 90222 (HFD hydraulic fluids) for detailed information regarding the choice of hydraulic fluid and application conditions.
If environmentally acceptable hydraulic fluids are being used, the limitations regarding technical data and other seals must be observed. Please contact us.
Operating viscosity range
For optimum efficiency and service life we recommend that the operating viscosity (at operating temperature) be selected in the range
nopt = opt. operating viscosity 80 - 170 SUS (16 ... 36 mm2/s)
referred to reservoir temperature (open circuit).
Limits of viscosity range
For critical operating conditions the following values apply:
nmin = 60 SUS (10 mm2/s) short-term (t ≤ 1 min) at max perm. case drain temperature of 239 °F (115 °C).
Please also ensure that the max. case drain temperature of 239 °F (115 °C) is not exceeded in localized areas (for instance, in the bearing area). The fluid temperature in the bearing area is approx. 7 °F (5 K) higher than the average case drain tempe-rature.
nmax = 7500 SUS (1600 mm2/s) short-term (t ≤ 1 min) on cold start (p ≤ 435 psi (30 bar), n ≤ 1000 rpm, tmin -13 °F (-25 °C))
Depending on the installation situation, special measures are necessary at temperatures between -40 °F (-40°C) and -13 °F (-25°C). Please contact us.
For detailed information on operation with low temperatures see data sheet RE 90300-03-B.
Selection diagram
Notes on the choice of hydraulic fluid
In order to select the correct hydraulic fluid, it is necessary to know the operating temperature in the reservoir (open circuit) in relation to the ambient temperature.
The hydraulic fluid should be selected so that within the ope-rating temperature range, the viscosity lies within the optimum range (nopt), see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case.
Example: at an ambient temperature of X °F (°C) the operating temperature is 140 °F (60 °C). In the optimum operating vis-cosity range (nopt; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; VG 68 should be selected.
Important: The case drain temperature is influenced by pressure and input speed and is always higher than the reservoir temperature. However, at no point in the component may the temperature exceed 239 °F (115 °C). The temperature difference specified on the left is to be taken into account when determining the viscosity in the bearing.
If the above conditions cannot be met, due to extreme opera-ting parameters please contact us.
Filtration of the hydraulic fluidThe finer the filtration the better the cleanliness level of the hyd-raulic fluid and the longer the service life of the axial piston unit.
In order to guarantee the functional reliability of the axial piston unit it is necessary to carry out a gravimetric evaluation of the hydraulic fluid to determine the particle contamination and the cleanliness level according to ISO 4406. A cleanliness level of at least 20/18/15 must be maintained. At very high hydraulic fluid temperatures (195 °F (90 °C) to ma-ximum 239 °F (115 °C)), a cleanliness level of at least 19/17/14 according to ISO 4406 is necessary.
If the above cleanliness levels cannot be maintained, please contact us.
-40° -4° 32° 68° 104° 140° 176° 212° °F
-40° -20° 0° 20° 40° 60° 80° 100° °C
-40° -25° 10° 0° 10° 30° °C50° 70° 90° 115°
-40° -13° 14° 32° 50° 86° °F122° 158° 194° 240°
160074001000460060030004002000
2001000
100500
60300
40200
20100
1060
mm2/sSUS542
80
74001600
17036
8016
425SUSmm2/s
t max = 240°F (115°C)t min = -40°F (-40°C)
VG 22VG 32VG 46VG 68VG 100
Visc
osity
n [
mm
2/s]
Temperature t in °CFluid temperature range
nopt
5/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Technical dataOperating pressure range (when using mineral oil)
Pressure at service line port B
Nominal pressure pnom ________ 4000 psi (280 bar) absolute
Maximum pressure pmax ______ 5100 psi (350 bar) absolute Single operating period ___________________________ 2.0 ms Total operating period _____________________________ 300 h
Minimum pressure (high-pressure side) _____________ 145 psi _________________________________________ (10 bar) absolute1)
Rate of pressure change RA max _ 232060 psi/s (16000 bar/s)
pnom
Dt
Dp
Time t
Pre
ssur
e p
Pressure at suction port S (inlet)Minimum pressure pS min ___________ 12 psi (0.8 bar) absolute Maximum pressure pS max _________145 psi (10 bar) absolute1)
NotePlease contact us for values for other hydraulic fluids.
Case drain pressure
Maximum permissible case drain pressure (at port L, L1): Maximum 0.5 bar higher than the inlet pressure at port S, however not higher than 2 bar absolute.
pL max abs _________________________ 30 psi (2 bar) absolute1)
Other values on request1)
Definition
Nominal pressure pnom
The nominal pressure corresponds to the maximum design pressure.
Maximum pressure pmax
The maximum pressure corresponds to the maximum operating pressure within the single operating period. The total of the single operating periods must not exceed the total operating period.
Minimum pressure (high-pressure side)Minimum pressure in the high-pressure side (port B) that is required in order to prevent damage to the axial piston unit. The minimum pressure depends on the speed and displace-ment of the axial piston unit.
Rate of pressure change RA
Maximum permissible pressure build-up and pressure reduc-tion speed with a pressure change over the entire pressure range.
Pre
ssur
e p t1
t2 tnSingle operating period
Minimum pressure (high-pressure side)
Maximum pressure pmaxNominal pressure pnom
Time t
Total operating period = t1 + t2 + ... + tn
(A)A10V(S)O Series 31 RA-A 92701/03.126/52 Bosch Rexroth Corp.
Technical data, standard unitTable of values (theoretical values, without efficiencies and tolerances: values rounded)
Size NG 18 28 45 71 100 140
Geometrical displacement per revolution
Vg max in3 (cm3) 1.10 (18) 1.71 (28) 2.75 (45) 4.33 (71) 6.1 (100) 8.54 (140)
Maximum speed 1)
at Vg max nnom rpm 3300 3000 2600 2200 2000 1800
at Vg < Vg max nmax perm rpm 3900 3600 3100 2600 2400 2100
Flow
at nnom and Vg max qv max gpm (l/min) 15.7 (59) 22 (84) 31 (117) 41 (156) 53 (200) 67 (252)
at nE = 1800 rpm and Vg max qvE max gpm (l/min) 8.5 (32) 13.3 (50) 21.4 (81) 33.8 (128) 47.6 (180) 67 (252)
Power at Dp = 4000 psi (280 bar)
at nnom, Vg max Pmax HP (kW) 40 (30) 51 (39) 74 (55) 96 (73) 124 (93) 156 (118)
at nE = 1800 rpm and Vg max PE max HP (kW) 19 (15) 31 (24) 50 (38) 79 (69) 111 (84) 156 (118)
Torque
at Vg max andDp = 4000 psi Dp = (280 bar)
Tmax lb-ft (Nm) 58 (80) 91 (125) 146 (200) 230 (316) 324 (445) 453 (623)
Dp = 1450 psi Dp = (100 bar)
T lb-ft (Nm) 14.6 (30) 33 (45) 53 (72) 83 (113) 117 (159) 164 (223)
Rotary stiffness, drive shaft S c
lb-ft/rad (Nm/rad)
8082 (11087)
16400 (22317)
27560 (37500)
53018 (71884)
89348 (121142)
125042 (169537)
R clb-ft/rad (Nm/rad)
10870 (14850)
19400 (26360)
30241 (41025)
56456 (76545)
– (–)
– (–)
U clb-ft/rad (Nm/rad)
5946 (8090)
12310 (16695)
22107 (30077)
38920 (52779)
67180 (91093)
– (–)
W clb-ft/rad (Nm/rad)
– (–)
14670 (19898)
25330 (34463)
42360 (57460)
74858 (101847)
– (–)
Moment of inertial rotary group JTWlbs-ft2 (kgm2)
0.022 (0.00093)
0.0403 (0.0017)
0.0783 (0.0033)
0.1970 (0.0083)
0.3963 (0.0167)
0.5743 (0.0242)
Angular acceleration, maximum2) a rad/s2 6800 5500 4000 3300 2700 2700
Filling capacity V gal (L) 0.1 (0.4) 0.2 (0.7) 0.26 (1.0) 0.4 (1.6) 0.6 (2.2) 0.8 (3.0)
Weight (without through drive) approx. m lbs (kg) 26.5 (12) 33 (15) 46 (21) 73 (33) 99 (45) 132 (60)
The values are applicable:1)
- for an absolute pressure pabs = 15 psi (1 bar) at suction port S - within the optimum viscosity range from nopt = 80 to 170 SUS (16 to 36 mm2/s) - for mineral-oil based hydraulic fluid.
The scope of application lies between the minimum necessary and the maximum permissible drive speeds. 2)
Valid for external excitation (e.g. diesel engine 2- to 8-fold rotary frequency, cardan shaft 2-fold rotary frequency). The limiting value is only valid for a single pump. The loading capacity of the connecting parts must be taken into account.
NoteExceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simulati-on and comparison with the permissible values.
Calculation of characteristics
Flow qV =Vg • n • hV [gpm
(l/min)]Vg = Displacement per revolution in cm3
231 (1000) Dp = Pressure differential in bar
Torque T =Vg • Dp [lb-ft
(Nm)]n = Speed in rpm
24 (20) • p • hmh hV = Volumetric efficiency
Power P =2p • T • n
=qV • Dp [HP
(kW)]hmh = Mechanical-hydraulic efficiency
33000 (60000) 1714 (600) • ht ht = Total efficiency (ht = hV • hmh)
7/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Technical data, high-speed versionTable of values (theoretical values, without efficiencies and tolerances: values rounded)
Size NG 45 71 100 140
Geometrical displacement per revolution
Vg max in3 (cm3) 2.75 (45) 4.33 (71) 6.1 (100) 8.54 (140)
Maximum speed 1)
at Vg max nnom rpm 3000 2550 2300 2050
at Vg < Vg max nmax perm rpm 3300 2800 2500 2200
Flow
at nnom and Vg max qv max gpm (l/min) 35 (135) 47 (178) 61 (230) 76 (287)
Power at Dp = 4000 psi (280 bar)
at nnom, Vg max Pmax HP (kW) 84 (63) 112 (83) 143 (107) 177 (134)
Torque
at Vg max andDp = 4000 psi Dp = (280 bar)
Tmax lb-ft (Nm) 146 (200) 230 (316) 324 (445) 453 (623)
Dp = 1450 psi Dp = 100 bar
T lb-ft (Nm) 53 (72) 83 (113) 117 (159) 164 (223)
Rotary stiffness, drive shaft S c
lb-ft/rad (Nm/rad)
27560 (37500)
53ß18 (71884)
89348 (121142)
125042 (169537)
R clb-ft/rad (Nm/rad)
30240 (41025)
56456 (76545)
– (–)
– (–)
U clb-ft/rad (Nm/rad)
22107 (30077)
– (–)
67180 (91093)
– (–)
W clb-ft/rad (Nm/rad)
25330 (34463)
– (–)
74858 (101847)
– (–)
Moment of inertial rotary group JTWlbs-ft2
(kgm2)0.0783 (0.0033)
0.1970 (0.0083)
0.3968 (0.0167)
0.5743 (0.0242)
Angular acceleration, maximum2) a rad/s2 4000 3300 2700 2700
Filling capacity V gal (L) 0.26 (1.0) 0.4 (1.6) 0.6 (2.2) 0.8 (3.0)
Weight (without through drive) approx. m lbs (kg) 46 (21) 73 (33) 99 (45) 132 (60)
The values are applicable:1)
- for an absolute pressure pabs = 15 psi (1 bar) at suction port S - within the optimum viscosity range from nopt = 80 to 170 SUS (16 to 36 mm2/s) - for mineral-oil based hydraulic fluid.
The scope of application lies between the minimum necessary and the maximum permissible drive speeds. 2)
Valid for external excitation (e.g. diesel engine 2- to 8-fold rotary frequency, cardan shaft 2-fold rotary frequency). The limiting value is only valid for a single pump. The loading capacity of the connecting parts must be taken into account.
NoteExceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simulati-on and comparison with the permissible values.
Sizes 45, 71, 100 and 140 are optionally available in high-speed version. External dimensions are not affected by this option.
(A)A10V(S)O Series 31 RA-A 92701/03.128/52 Bosch Rexroth Corp.
Technical dataPermissible radial and axial loading on the drive shaft
Size NG 18 28 45 71 100 140
Radial force maximum at a/2
Fq maxlbf (N)
80 (350)
270 (1200)
340 (1500)
427 (1900)
517 (2300)
630 (2800)
Axial force maximum
+ Fax maxlbf (N)
157 (700)
225 (1000)
340 (1500)
540 (2400)
900 (4000)
1080 (4800)
Permissible input and through-drive torques
Size NG 18 28 45 71 100 140
Torque at Vg max and Dp = 4000 psi (280 bar1))
Tmaxlb-ft (Nm)
58 (80)
91 (125)
146 (200)
230 (316)
324 (445)
453 (623)
Input torque for drive shaft, maximum2)
S TE maxlb-ft (Nm)
92 (124)
146 (198)
235 (319)
462 (626)
814 (1104)
1195 (1620)
Ø in 3/4 7/8 1 1 1/4 1 1/2 1 3/4
R TE maxlb-ft (Nm)
118 (160)
184 (250)
295 (400)
475 (644)
– (–)
– (–)
Ø in 3/4 7/8 1 1 1/4 – –
U TE maxlb-ft (Nm)
44 (59)
77 (105)
139 (188)
221 (300)
439 (595)
– (–)
Ø in 5/8 3/4 7/8 1 1 1/4 –
W TE maxlb-ft (Nm)
– (–)
103 (140)
162 (220)
291 (394)
469 (636)
– (–)
Ø in – 3/4 7/8 1 1 1/4 –
Maximum through-drive torque for drive shaft
S TD maxlb-ft (Nm)
80 (108)
118 (160)
235 (319)
363 (492)
574 (778)
934 (1266)
R TD max Nm89 (120)
130 (176)
269 (365)
404 (548)
– (–)
– (–)
Without considering efficiency1)
For drive shafts free of radial force2)
Distribution of torques
±Fax
Fq
a
a/2 a/2
2. Pumpe1. Pumpe
TE
TD
T1 T2
1st pump 2nd pump
9/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Technical dataDrive power and flowOperating material: Hydraulic fluid ISO VG 46 DIN 51519, t = 122 °F (50 °C)
Size 18
_ _ _ _ n = 1800 rpm
______n = 3300 rpm
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi 0
(30)
(20)
(10)
(40)
HP(kW)
20
40qv Pqv max
Pqv zero
Flow
qV
Driv
e po
wer
POperating pressure
Size 28
_ _ _ _ n = 1800 rpm
______n = 3000 rpm
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi 0
(30)
(20)
(10)
(40)
HP(kW)60
20
40qv Pqv max
Pqv zero
Flow
qV
Driv
e po
wer
P
Operating pressure
Size 45
_ _ _ _ n = 1800 rpm
______n = 2600 rpm
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
30(100)
(120)
0
(30)
(20)
(10)
(40)
HP(kW)
(50)
(60) 80
40
60
20
qv
Pqv max
Pqv zeroFlow
qV
Driv
e po
wer
P
Operating pressure
Size 71
_ _ _ _ n = 1800 rpm
______n = 2200 rpm
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
30(100)
(120)
40(140)
(160)
0
(30)
(20)
(10)
(40)
HP(kW)
(50)
(60)
(70)
(80)100
40
20
60
80
qv
Pqv max
Pqv zero
Flow
qV
Driv
e po
wer
P
Operating pressure
Size 100
_ _ _ _ n = 1800 rpm
______n = 2000 rpm
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
30(100)
(120)
40(140)
(160)
50(180)
(200)
0
(30)
(20)
(10)
(40)
HP(kW)
(50)
(60)
(70)
(80)
(90)
(100)
40
20
60
80
100
120
qv
Pqv max
Pqv zero
Flow
qV
Driv
e po
wer
P
Operating pressure
Size 140
______n = 1800 rpm
(280)(250)(200)(150)(100)(50)0
40003500250015001000500 2000 3000
(bar)
psi
20
10
0
(60)
(40)
(20)
(80)
gpm(L/min)
30(100)
(120)
40(140)
(160)
50(180)
(200)
60(220)
(240)
(260)
0
20
(30)
(20)
(10)
(40)60
(50)
(60)
(70)
(80)
(90)
(100)
HP(kW)
(110)
(120)
(130)
120
140
160
100
80
40
qv
Pqv max
Pqv zero
Flow
qV
Driv
e po
wer
P
Operating pressure
(A)A10V(S)O Series 31 RA-A 92701/03.1210/52 Bosch Rexroth Corp.
DG – Two-point control, directly operatedCircuit diagram
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
X Pilot pressure
The variable pump can be set to a minimum swivel angle by connecting an external control pressure to port X.
This will supply control fluid directly to the stroke piston; a minimum control pressure of pst ≥ 725 psi (50 bar) is requi-red.
The variable pump can only be switched between Vg max or Vg min.
Please note, that the required control pressure at port X is directly dependent on the actual operating pressure pB in port B. (See control pressure characteristic).
Control pressure pst in X = 0 psi (0 bar) Vg max
Control pressure pst in X ≥ 725 psi (50 bar) Vg min
Control pressure characteristic
X
L B
SL1
0 40007251020 2040 3060
(120)
(100)
(50)
psi(bar) (280)(50)(70) (140) (210)
1720
1455
725
(bar)psi
Req
. con
trol
pre
ssur
e p s
t
Operating pressure pB
11/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
DR – Pressure controlCircuit diagram, sizes 18 to 100
Circuit diagram, size 140
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
Control data
Hysteresis and repeatability Dp ______ maximum 45 psi (3 bar)
Pressure rise, maximum
NG 18 28 45 71 100 140
Dp psi (bar)
60 (4)
60 (4)
90 (6)
115 (8)
145 (10)
175 (12)
Control fluid consumption _____ max. approx. 0.8 gpm (3 l/min)
Flow losses at qVmax see page 9.
The pressure control limits the maximum pressure at the pump output within the pump control range. The variable pump only supplies as much hydraulic fluid as is required by the consu-mers. If the operating pressure exceeds the pressure setpoint set at the integrated pressure valve, the pump will adjust towards a smaller displacement and the control deviation will be reduced. The pressure can be set steplessly at the control valve.
Static characteristic
(at n1 = 1800 rpm; tfluid = 122 °F (50 °C))
In order to prevent damage to the pump and the system, 1)
this setting range is the permissible setting range and must not be exceeded. The range of possible settings at the valve are greater.
L B
SL1
(25)
(280)
365
4000
(bar)psi
Ope
ratin
g pr
essu
re p
B
Hys
tere
sis
/ pr
essu
re ri
se D
p max
Set
ting
rang
e1)
Flow qv [gal (l/min)]
(A)A10V(S)O Series 31 RA-A 92701/03.1212/52 Bosch Rexroth Corp.
The DR-control valve (see page 11) is overriding this DRG-remote setting of max. outlet pressure.
A pressure relief valve can be externally piped to port X for remote setting of pressure below the setting of the DR control valve spool. This relief valve is not included in the delivery contents of the DRG control.
The differential pressure at the DRG control valve is set as standard to 290 psi (20 bar). This results in a pilot oil flow to the relief valve of approx. 0.4 gpm (1.5 l/min) at port X. If ano-ther setting is required (range from 145-320 psi (10-22 bar)) please state in clear text.
As a separate pressure relief valve we can recommend:
DBDH 6 (hydraulic) to RE 25402 or
DBETR-SO 381 with orifice dia 0.03 inch (Ø 0.8 mm) in P (electric) to RE 29166.
The max. length of piping should not exceed 6.5 ft (2 m).
Static characteristic
(at n1 = 1800 rpm; tfluid = 122 °F (50 °C))
In order to prevent damage to the pump and the system, 1)
this setting range is the permissible setting range and must not be exceeded. The range of possible settings at the valve are greater.
Circuit diagram, sizes 18 to 100
Circuit diagram, size 140
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
X NG 18 to 100 with adapter
Pilot pressure
X NG 140 without adapter
Pilot pressure
Control data
Hysteresis and repeatability Dp ______ maximum 45 psi (3 bar)
Pressure rise, maximum
NG 18 28 45 71 100 140
Dp psi (bar)
60 (4)
60 (4)
90 (6)
115 (8)
145 (10)
175 (12)
Control fluid consumption ____max. approx. 1.2 gpm (4.5 l/min)
Flow losses at qVmax see page 9.
DRG – Pressure control, remotely operated
L B
SL1
X
X
(20)
(280)
290
4000(bar)psi
Flow qv [gpm (l/min)]
Ope
ratin
g pr
essu
re p
B
Hys
tere
sis
/ pr
essu
re ri
se D
p max
Set
ting
rang
e1)
Not included in the delivery contents
Not included in the delivery contents
13/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
In addition to the pressure control function (see page 11), the pump flow may be varied by means of a differential pressure over an adjustable orifice (e.g. directional valve) installed in the service line to the actuator. The pump flow is equal to the actual required flow by the actuator, regardless of changing pressure levels.
The pressure control overrides the flow control function.
Note The DFR1 version has no connection between X and the reservoir. Unloading the LS-pilot line must be possible in the valve system. Because of the flushing function sufficient unloading of the X-line must also be provided.
Static characteristic
Flow control at n1 = 1800 rpm; tfluid = 122 °F (50 °C))
In order to prevent damage to the pump and the system, 1)
this setting range is the permissible setting range and must not be exceeded. The range of possible settings at the valve are greater.
Static characteristic at variable speed
Differential pressure Dp
Standard setting: 200 to 320 psi (14 to 22 bar). If another setting is required, please state in clear text. Relieving the load on port X to the reservoir results in a zero stroke ("standby") pressure which lies about 15 to 30 psi (1 to 2 bar) higher than the differential pressure Dp. System influen-ces are not taken into account.
DFR/DFR1 – Pressure and flow controlCircuit diagram, sizes 18 to 100
Circuit diagram, size 140
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
X Pilot pressure
Control data
Data for pressure control DR, see page 11. Maximum flow deviation measured with drive speed n = 1500 rpm.
NG 18 28 45 71 100 140
Dqv max gpm (l/min)
0.24 (0.9)
0.26 (1.0)
0.48 (1.8)
0.75 (2.8)
1.06 (4.0)
1.60 (6.0)
Control fluid consumption DFR __ max. approx. 0.8 to 1.2 gpm (3 to 4.5 l/min) Control fluid consumption DFR1 ___maximum approx. 0.8 gpm (3 l/min) Volume flow loss at qVmax, see page 9.
X
L B
SL1
X
B
(25)
(280)
365
4000(bar)psi
Flow qv [gpm (l/min)]
Hys
tere
sis
/ pr
essu
re ri
se D
p m
ax
Set
ting
rang
e1)
Not
incl
uded
in th
e de
liver
y co
nten
tsN
ot in
clud
ed in
the
deliv
ery
cont
ents
With DFR1 plugged
With DFR1 plugged
Speed n [rpm]
Flow
qv [
gpm
(l/m
in)]
Hys
tere
sis
/ pr
essu
re ri
se D
p max
Ope
ratin
g pr
essu
re p
B
(A)A10V(S)O Series 31 RA-A 92701/03.1214/52 Bosch Rexroth Corp.
DFLR – Pressure, flow and power controlExecution of the pressure control like DR(G), see page 11 (12). Execution of the flow control like DFR, DFR1, see page 13.
In order to achieve a constant drive torque with varying opera-ting pressures, the swivel angle and with it the output flow from the axial piston pump is varied so that the product of flow and pressure remains constant.
Flow control is possible below the power control curve.
The power characteristic is set in the factory; when ordering, please state in clear text, e.g. 40 HP (30 kW) at 1800 rpm.
Control data
For pressure control DR data, see page 11. For flow control FR data, see page 13.
Circuit diagram, size 140
Circuit diagram, sizes 28 to 100
Static curves and torque characteristic
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
X Pilot pressure
Control data
Beginning of control ____________________ 725 psi (50 bar) Control fluid consumption _ maxi. approx. 1.45 gpm (5.5 l/min)
Flow loss at qv max, see page 9.
X
L B
SL1
X
L B
SL1
(0)
(50)
∆qV
(100)
(150)
(200)
(250)
(280)(300)
0 100
0
725
1450
2200
2900
3600
40004350
(bar)psi
Ope
ratin
g pr
essu
re p
B
Volume flow qv [%]
Maximum power curve
Maximum power curve
(see table on page 13)
Torq
ue T
[lb
-ft (
Nm
)]
Not included in the delivery contents
Not included in the delivery contents
15/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
ED – Electro-hydraulic pressure controlThe ED valve is set to a certain pressure by a specified, variable solenoid current.
If there is a change at the consumer (load pressure), the position of the control piston changes.
This causes an increase or decrease in the pump swivel angle (flow) in order to maintain the electrically set pressure level.
The pump thus only delivers as much hydraulic fluid as the consumers can take. The desired pressure level can be set steplessly by varying the solenoid current.
When the solenoid current signal drops towards a zero value, the maximum output pressure is limited to pmax by an adjustable hydraulic pressure cut-off (secure fail safe function in case of a loss of power e.g. for use as fan drives). The response time characteristic of the ED-control was optimized for the use as a fan drive system. When ordering, state the type of application in clear text.
Static current-pressure characteristic ED (measured at pump in zero stroke – negative characteristic)
Hysteresis of the static current-pressure characteristic < 45 psi (3 bar)
Static flow-pressure characteristic(at n= 1800 rpm; tfluid = 122 °F (50 °C))
Control dataStandby standard settings (see diagram at right), other values on request.
Hysteresis and pressure increase ________Dp < 60 psi (4 bar) Control fluid consumption _____ 0.8 to 1.2 gpm (3 to 4.5 l/min)
Influence of pressure setting on standby level
Circuit diagram ED..
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
Technical data, solenoid ED71 ED72
Voltage 12 V (±20 %) 24 V (±20 %)
Control current
Start of control at Vg min 100 mA 50 mA
End of control at Vg max 1200 mA 600 mA
Limiting current 1.54 A 0.77 A
Nominal resistance (at 20 °C) 5.5 Ω 22.7 ΩDither frequency 100 to
200 Hz100 to 200 Hz
Actuated time 100 % 100 %For type of protection, see plug design on page 47 For details on the control electronics, see page 16
Operating temperature range at valve -4 °F to 239 °F (-20 °C to +115 °C)
(280)
0(0)
I/ Imax1
ED
(140)
4000(bar)psi
0
2050
B
SL1
L
(30)
(28)
(26)
(24)
(22)
(20)
(18)
(16)
(14)
435(bar)psi
(bar)psi
405
360
350
320
290
260
230
200
(120) (140) (160) (180) (200) (220) (240) (260) (280)1750 2000 2350 2700 2900 3200 3500 3700 4000
(140)
(280)
2050
4000(bar)psi
Ope
ratin
g pr
essu
re
Amperage
De-activation of controlMax. adjustable control pressure
Min. adjustable control pressure
Hys
tere
sis
/ pr
essu
re ri
se D
p
Ope
ratin
g pr
essu
re p
Set
ting
rang
e
max
min
Flow qv [gpm (l/min)] maxmin
Maximum pressure setting
Sta
ndby
(A)A10V(S)O Series 31 RA-A 92701/03.1216/52 Bosch Rexroth Corp.
ER – Electro-hydraulic pressure controlThe ER valve is set to a specific pressure by a specified, variable solenoid current.
If there is a change at the consumer (load pressure), the position of the control piston changes.
This causes an increase or decrease in the pump swivel angle (flow) in order to maintain the electrically set pressure level.
The pump thus only delivers as much hydraulic fluid as the consumers can take. The desired pressure level can be set steplessly by varying the solenoid current.
If the solenoid current drops to zero, the pressure is limited to pmin (stand-by).
Observe the project planning note on page 2.
Static current-pressure characteristic ER (measured at pump in zero stroke – positive characteristic)
Hysteresis of the static current-pressure characteristic < 45 psi (3 bar)
Influence of pressure setting on stand-by ±30 psi (±2 bar)
Static flow-pressure characteristic(at n= 1800 rpm; tfluid = 122 °F (50 °C))
Control dataStandby standard setting 290 psi (20 bar), other values on request.
Hysteresis and pressure increase ________Dp < 60 psi (4 bar) Control fluid consumption _____ 0.8 to 1.2 gpm (3 to 4.5 l/min)
Circuit diagram ER..
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged)
Technical data, solenoid ER71 ER72
Voltage 12 V (±20 %) 24 V (±20 %)
Control current
Start of control at Vg min 100 mA 50 mA
End of control at Vg max 1200 mA 600 mA
Limiting current 1.54 A 0.77 A
Nominal resistance (at 20 °C) 5.5 Ω 22.7 ΩDither frequency 100 to
200 Hz100 to 200 Hz
Actuated time 100 % 100 %
For type of protection, see plug design on page 47
Operating temperature range at valve -4 °F to 239 °F (-20 °C to +115 °C)
The following electric controllers and amplifiers are available for controlling the proportional solenoids:
Analog amplifier RA RE 95230 Digital controller RC2-2/211) RE 95201 Analog amplifier VT20002) RE 29904 Analog amplifier VT 11029/110302) RE 29741
Power outlets for 2 valves, can be actuated separately1)
Only 24V nominal voltage2)
B
SL1
L
(140)
(280)
2050
4000(bar)psi
0 1(0)
(50)
(150)
(250)
(280)(350)
0
725
2200
3600
40005100
(bar)psi
I/Imax
Ope
ratin
g pr
essu
re
Amperage
Max. adjustable control pressure
Min. adjustable
control pressure
Hys
tere
sis
/ pr
essu
re ri
se D
p
Ope
ratin
g pr
essu
re p
Set
ting
rang
e
max
min
Flow qv maxmin
17/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Notes
(A)A10V(S)O Series 31 RA-A 92701/03.1218/52 Bosch Rexroth Corp.
Dimensions size 18 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
DFR, DFR1 – Pressure and flow control, hydraulic Clockwise rotation
PortsDesignation Port for Standard Size1) Max. press.
[psi /(bar)]2)State
B Service line, fastening thread
SAE J518 ASME B1.1
3/4 in 3/8-16 UNC-2B; 0.79 (20) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
1 in 3/8-16 UNC-2B; 0.79 (20) deep
145 psi (10) O
L Case drain fluid ISO 119263) 9/16-18UNF-2B; 0.47 (12) deep 30 (2) O4)
L1 Case drain fluid ISO 119263) 9/16-18UNF-2B; 0.47 (12) deep 30 (2) X4)
X Pilot pressure ISO 119263) 7/16-20UNF-2B; 0.45 (11.5) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2283) G 1/4 in; 0.47 (12) deep 5100 (350) O
For the maximum tightening torques the general instructions on page 52 must be observed.1)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 2)
fittings. Pressure values in psi (bar) absoluteThe spot face can be deeper than as specified in the standard3)
Depending on the installation position, L or L4) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
7.68 (195)
2.48
(63
)2.
48 (6
3)
W
V
5.71 (145)
XL
L1
5.08 (129)
1.69 (43)
(Ø82
.55
)
3.25
003.
2479
DIA
-0.0
540
0.25 (6.3)3.27 (83)
0.45(11.5)
2.06
(52.
4)
1.03(26.2)
S
S
DIA
0.9
8(Ø
25)
1.87
(47.
6)D
IA 0
.79
(Ø20
)
B
B
0.87 (22.2)
L
4.96 (126)
1.57
(40
)
5.98 (152)
2.60 (66)
0.43 (11)
4.29 (109)
max
. 4.3
3 (1
10)
2.52
(64)
2.72
(69
)
4.19 (106.4)
45°45°
X
View W
Valve mounting for counter-clockwise rotation
View V
Flange ISO 3019-1
19/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 18 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
Drive shaftS Splined shaft 3/4 in
11T 16/32DP1) (SAE J744)R Splined shaft 3/4 in
11T 16/32DP1)2) (SAE J744)U Splined shaft 5/8 in
9T 16/32DP1)2) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Splines according to ANSI B92.1a, run out of spline is a deviation from standard2)
Thread according to ASME B1.13)
For the maximum tightening torques the general instructions on page 52 must be observed4)
Coupling axially secured, e.g. with a clamp coupling or radially mounted clamping screw5)
1.50 (38)
0.55 (14)0.20 (5)
1.18 (30)
0.83 (21)
1/4-
20U
NC
-2B
3) 4
)
1/4-
20U
NC
-2B
3) 4
)
0.55 (14)
1.50 (38)
0.83 (21)
0.20 (5)
1.25 (31.8)
0.94 (23.8)
0.62(15.8)
Centering5) R 0.12 x 0.26 (R 3.15 x 6.7) DIN 332
Usable shaft length
(A)A10V(S)O Series 31 RA-A 92701/03.1220/52 Bosch Rexroth Corp.
Dimensions size 18DGTwo-point control, directly operated
DRPressure control
DRGPressure control, remotely operated
ED7., ER7.Electro-hydraulic pressure control
ER7.: 6.34 in (161 mm) if using a sandwich plate pressure reducing valve.1)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
0.12
(3)
(25
)0.
981.
00+
0.4
3.50 (89)3.82 (97)
X
5.83 (148)
4.96 (126)
max
. 4.3
3 (1
10)
X
X
5.08 (129)
4.96 (126)
1.57
(40
)
4.29 (109)
max
. 4.3
3 (1
10)
X
4.96 (126)1)
5.51
(140
)
X
7.24 (184)
to flange surface
to flange surface
to flange surface
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
21/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 28DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation
Details on connection options and shaft ends can be found on page 22
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
-0.0
540
-0.0
540
X
S2.
31 (5
8.7)
1.26
(Ø32
)
1.19 (30.2)
B
0.87 (22.2)
DIA
0.7
9(Ø
20)
1.87
(47.
6)
(Ø10
1.6
)
4.00
003.
9979
DIA
3.15
(80
)3.
15 (
80)
7.64 (194)
0.55 (14)1.57 (40)
XL L
L16.46 (164)
0.25 (6.3)0.37 (9.5)
W
Z
V
3.54 (90)5.47 (139)
5.35 (136)4.68 (119)
2.91 (7
4)
3.29 (83.5)
5.75 (146)6.46 (164)
max
. 4.3
3 (1
10)
1.57
(40
)2.
91 (7
4)
DIA 0
55 (14)
45°45°
6.85 (Ø174)
S
B
S
B
1.69
(43)
max
. 4.4
5 (1
13)
0.87
(22.
2)1.1
9 (3
0.2)
X
DIA 1.25 (Ø32)2.31 (58.7)
1.77
(45)
1.77
(45)
0.79(Ø20)
1.87 (47.6)
0.55 (14)1.57 (40) L1
L
6.69 (170)8.23 (209)
8.90 (226)
0.25 (6.3)0.37 (9.5) 3.54 (90)
3.11
(79
)
2.87 (73)
(Ø10
1.6
)
4.00
003.
9979
DIA
Detail V Detail W
Flange ISO 3019-1
Flange ISO 3019-1
Valve mounting for ccw rotation
View ZValve mounting for ccw rotation
Port plate 62
Port plate 61
(A)A10V(S)O Series 31 RA-A 92701/03.1222/52 Bosch Rexroth Corp.
Dimensions size 28Drive shaftS Splined shaft 7/8 in
13T 16/32DP1) (SAE J744)R Splined shaft 7/8 in
13T 16/32DP1)2) (SAE J744)U Splined shaft 3/4 in
11T 16/32DP1) (SAE J744)
W Splined shaft 3/4 in 11T 16/32DP1)2) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Spline according to ANSI B92.1a, run out of spline is a deviation from standard.2)
Thread according to ASME B1.13)
For the maximum tightening torques the general instructions on page 52 must be observed.4)
PortsDesignation Port for Standard Size5) Max. press.
[psi (bar)]6)State
B Service line, fastening thread
SAE J518 ASME B1.1
3/4 in 3/8-16 UNC-2B; 0.79 (20) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
1 1/4 in 7/16-14 UNC-2B; 0.94 (24) deep
145 (10) O
L Case drain fluid ISO 119267) 3/4-16 UNF-2B; 0.55 (14) deep 30 (2) O8)
L1 Case drain fluid ISO 119267) 3/4-16 UNF-2B; 0.55 (14) deep 30 (2) X8)
X Pilot pressure ISO 119267) 7/16-14UNC-2B; 0.45 (11.5) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2287) G 1/4in; 0.47 (12) deep 5100 (350) O
For the maximum tightening torques the general instructions on page 52 must be observed.5)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 6)
fittings. Pressure values in psi (bar) absolute.The spot face can be deeper than as specified in the standard.7)
Depending on the installation position, L or L8) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
1.61 (41)
0.63 (16)0.20(5)
1.30 (33.1)
0.99(25.1)
1/4-
20U
NC
-2B
3) 4
)
1/4-
20U
NC
-2B
3) 4
)
0.63 (16)
1.61 (41)
0.98 (25)
0.20 (5)
1.50 (38)
0.55 (14)0.20 (5)
1.18 (30)
0.87(22)
1/4-
20U
NC
-2B
3) 4
)
1/4-
20U
NC
-2B
3) 4
)
0.55 (14)
1.50 (38)
0.83 (21)
0.20 (5)
Usable shaft length
Usable shaft length
23/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 28DGTwo-point control, directly operated, port plate 61
DGTwo-point control, directly operated, port plate 62
DRPressure control, port plate 61
DRPressure control, port plate 62
DRGPressure control, remotely operated, port plate 61
DRGPressure control, remotely operated, port plate 62
For details of connection options and drive shafts, see also pages 21 and 22
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
Z
7.46 (189.5)7.75 (197)
3.11
(79
)
2.16 (55)
X
0.12
(3)
Ø25
0.98
1.00
DIA
+0.
4m
ax. 4
.45
(113
)
8.90 (226)
Z
1.69
(43
)m
ax. 4
.45
(113
)
8.23 (209)8.90 (226)
2.91 (74)
Z
X
L
0.12
(3)
Ø25
1.00
0.98
DIA
+0.
4
3.92 (99.5)4.07 (103.5)
X
6.22 (158)
X
5.35 (136)
max
. 4.3
3 (1
10)
X
5.08(129) X
5.35 (136)4.69 (119)
max
. 4.3
3 (1
10)
1.57
(40
)
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
View Z
View Z
View Z
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
to flange surface
to flange surface
to flange surface
(A)A10V(S)O Series 31 RA-A 92701/03.1224/52 Bosch Rexroth Corp.
Dimensions size 28DFLRPressure, flow and power control, port plate 61
DFLRPressure, flow and power control, port plate 62
ED7. / ER7.Electro-hydraulic pressure control, port plate 61
ED7. / ER7.Electro-hydraulic pressure control, port plate 62
ER7.: 10.24 in (260 mm) when using a sandwich plate pressure reducing valve.1)
ER7.: 6.83 in (170.9 mm) when using a sandwich plate pressure reducing valve.2)
For details of connection options and drive shafts, see also pages 21 and 22
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
4.69 (119)
3.39
(86
)1.93 (49)
max
. 4.4
5 (1
13)
X
8.90 (226)
1.89 (48)
5.35 (136) max
.4.3
3 (1
10)
4.69 (119)
1.57
(40
)
7.79 (198)
X
5.63
(143
)
8.86 (225)1)
Z
6.21 (157.8)1.40 (35.6)
5.35 (136)2)
5.51
(140
)
View Z
View Z
Valve mounting for ccw rotation see page 21
Valve mounting for ccw rotation Valve mounting for
ccw rotation
Valve mounting for ccw rotation
25/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 45DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation
Details on connection options and shaft ends can be found on page 26
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
-0.0
540
Z
X
X
1.40 (35.7)
DIA
1.5
7 (Ø
40)
2.75
(69
.9) S
B
DIA
0.9
8(Ø
25)
2.06
(52.
4)
1.03(26.2)
5.08 (129)5.75 (146)
6.06 (154)
3.54
(90
)3.
54 (9
0)
max
. 4.3
3 (1
10)
1.57
(40
)
5.75 (146)
0.37 (9.5)
LL
X
L1
(Ø10
1.6
)3.
9979
4.00
00D
IA3.
9979
4.00
00D
IA
-0.0
540
(Ø10
1.6
)
8.62 (219)
7.24 (184)
3.78 (96)0.25 (6.3)
7.24 (184)1.77 (45)
0.56 (14.3)
3.17
(80.
5)
3.68 (93.5)
DIA 0
.55
(Ø14
)3.27 (8
3)
45°45°
88
B
S
1.57 (Ø40)2.75(69.9)
DIA 0.98 (Ø25)2.06 (52.4)
1.03
(26.
2)1.
40 (3
5.7)
1.97
(50)
1.97
(50)
X
3.23 (82)
9.65 (245)
40 max
. 110
7.44 (189)
0.37 (9.5)
L
L1
8.98 (228)3.78 (96)0.25 (6.3)
1.77 (45)0.56 (14.3)
W
V
View WDetail V
Flange ISO 3019-1
Flange ISO 3019-1
View Z
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Port plate 62
Port plate 61
(A)A10V(S)O Series 31 RA-A 92701/03.1226/52 Bosch Rexroth Corp.
Dimensions size 45Drive shaftS Splined shaft 1 in
15T 16/32DP1) (SAE J744)R Splined shaft 1 in
15T 16/32DP1)2) (SAE J744)U Splined shaft 7/8 in
13T 16/32DP1) (SAE J744)
W Splined shaft 7/8 in 13T 16/32DP1)2) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Spline according to ANSI B92.1a, run out of spline is a deviation from standard.2)
Thread according to ASME B1.13)
For the maximum tightening torques the general instructions on page 52 must be observed.4)
PortsDesignation Port for Standard Size5) Max. press.
[psi (bar)]6)State
B Service line, fastening thread
SAE J518 ASME B1.1
1 in 3/8-16 UNC-2B; 0.71 (17) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
1 1/2 in 1/2-13 UNC-2B; 0.87 (20) deep
145 (10) O
L Case drain fluid ISO 119267) 7/8-14 UNF-2B; 0.63 (16) deep 30 (2) O8)
L1 Case drain fluid ISO 119267) 7/8-14 UNF-2B; 0.63 (16) deep 30 (2) X8)
X Pilot pressure ISO 119267) 7/16-20UNF-2B; 0.45 (11.5) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2287) G 1/4 in; 0.47 (12) deep 5100 (350) O
For the maximum tightening torques the general instructions on page 52 must be observed.5)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 6)
fittings. Pressure values in psi (bar) absolute.The spot face can be deeper than as specified in the standard.7)
Depending on the installation position, L or L8) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
1.81 (45.9)
0.63 (16)0.20 (5)
1.50 (38)
1.18 (30)
1/4-
20U
NC
-2B
3) 4
)
1.61 (41)
0.63 (16)0.20 (5)
1.30 (33.1)
0.98(25.1)
1/4-
20U
NC
-2B
3) 4
)
1/4-
20U
NC
-2B
3) 4
)
0.63 (16)
1.81 (45.9)
1.16 (29.5)
0.20 (5)
1/4-
20U
NC
-2B
3) 4
)
0.63 (16)
1.61 (41)
0.98 (25)
0.20 (5)
Usable shaft length
Usable shaft length
27/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 45DGTwo-point control, directly operated, port plate 61
DGTwo-point control, directly operated, port plate 62
DRPressure control, port plate 61
DRPressure control, port plate 62
DRGPressure control, remotely operated, port plate 61
DRGPressure control, remotely operated, port plate 62
For details of connection options and drive shafts, see pages 25 and 26
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
0.12
(3)
(Ø25
)
1.00
0.98
DIA
+0.
4
2.50(63.5)
X
8.21 (208.5)8.50 (216)
Z
(Ø25
)
0.98
1.00
DIA
+0.
4
6.81 (173)
4.33 (110)4.61 (117)
X
0.12
(3)
X
Z
9.65 (245)
max
. 4.3
3 (1
10)
X
5.75 (146)
max
. 4.3
3 (1
10)
B
X
X
3.23 (82)
9.65 (245)
1.57
(40
)m
ax. 4
.33
(110
)
8.98 (228)
Z
X
5.08 (129)5.75 (146)
6.06 (154)
max
. 4.3
3 (1
10)
1.57
(40
)X
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
View Z
View Z
View Z
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
to flange surface
to flange surface
to flange surface
(A)A10V(S)O Series 31 RA-A 92701/03.1228/52 Bosch Rexroth Corp.
Dimensions size 45DFLRPressure, flow and power control, port plate 61
DFLRPressure, flow and power control, port plate 62
ED7. / ER7.Electro-hydraulic pressure control, port plate 61
ED7. / ER7.Electro-hydraulic pressure control, port plate 62
ER7.: 10.98 in (279 mm) when using a sandwich plate pressure reducing valve1)
ER7.: 7.11 in (180.5 mm) when using a sandwich plate pressure reducing valve.2)
For details of connection options and drive shafts, see also pages 21 and 22
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
X
4.41
(112
)
1.93 (49)3.
58 (9
1)
9.65 (245)m
ax. 4
.33
(110
)
X
5.04 (128)
2.13 (54)
1.57
(40
)
5.08 (129)
X
4.41
(112
)
8.39 (213)
5.75 (146)
1.40 (35.6)
5.73 (145.5)2)
5.51
(140
)
X
1.42 (36)
2.50(63.5)
5.51
(140
)
9.60 (244)1)
Z
View Z
Valve mounting for ccw rotation see page 25
Valve moun-ting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
29/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 71DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation
Details on connection options and shaft ends can be found on page 30
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
L
S
B
X
L
3.06
(77.
8)
DIA
1.9
7(Ø
50)
S
1.69 (42.9)DIA 0.98 (Ø25)
2.06 (52.4)
1.03
(26.
2)
B
10.12 (257)
V
W
3.62
(92)
max
. 4.3
3 (1
10)
5.63 (143)4.23 (107.5)6.30 (160)
1.57
(40
)
2.09 (53)0.71 (18)
(Ø12
7
)
4.99
75D
IA5.
0000
-0.0
630
(Ø12
7
)
4.99
75D
IA5.
0000
-0.0
630
DIA 071 (Ø
18)
3.86 (98)
7.13 (181)8.27 (210)
L1
L
4.09
(104
)4.
09 (1
04)
7.20 (183)0.24 (6) 4.53 (115)
0.50 (12.7)
45°45°
X
8.54 (217)
X
2.09 (53)0.71 (18)
L
L1
8.78 (223)10.98 (279)
max
. 4.3
3 (1
10)
1.57
(40
)
0.24 (6) 4.53 (115)10.31(262)0.50 (12.7)
Z
(1.6
9 (4
2.9
)
3.06(77.8)
1.03 (26.2)DIA 098 (Ø25)
2.28
(58)
2.28
(58)
B
S
X
2.06
(52.
4)
DIA 1.97 (Ø50)
3.62 (92)
Detail V Detail W
Flange ISO 3019-1
Flange ISO 3019-1
Valve mounting for ccw rotation
Port plate 92
Port plate 91 Valve mounting for ccw rotation
(A)A10V(S)O Series 31 RA-A 92701/03.1230/52 Bosch Rexroth Corp.
Dimensions size 71Drive shaftS Splined shaft 1 1/4 in
14T 12/24DP1) (SAE J744)R Splined shaft 1 1/4 in
14T 12/24DP1)2) (SAE J744)U Splined shaft 1 in
15T 16/32DP1) (SAE J744)
W Splined shaft 1 in 15T 16/32DP1)2) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Spline according to ANSI B92.1a, run out of spline is a deviation from standard.2)
Thread according to ASME B1.13)
For the maximum tightening torques the general instructions on page 52 must be observed.4)
PortsDesignation Port for Standard Size5) Max. press.
[psi (bar)]6)State
B Service line, fastening thread
SAE J518 ASME B1.1
1 in 3/8-16 UNC-2B; 0.71 (18) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
2 in 1/2-13 UNC-2B; 0.87 (22) deep
145 (10) O
L Case drain fluid ISO 119267) 7/8-14 UNF-2B; 0.63 (16) deep 30 (2) O8)
L1 Case drain fluid ISO 119267) 7/8-14 UNF-2B; 0.63 (16) deep 30 (2) X8)
X Pilot pressure ISO 119267) 7/16-20 UNF-2B; 0.45 (11.5) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2287) G 1/4 in; 0.47 (12) deep 5100 (350) O
For the maximum tightening torques the general instructions on page 52 must be observed.5)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 6)
fittings. Pressure values in psi (bar) absolute.The spot face can be deeper than as specified in the standard.7)
Depending on the installation position, L or L8) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
2.18(55.4)
0.75 (19)0.20 (5)
1.87 (47.5)
1.56(39.5)
5/16
-18U
NC
-2B
3) 4
)
5/16
-18U
NC
-2B
3) 4
)
0.75 (19)
2.18 (55.4)
1.50 (38)
0.20 (5)
45.9
0.63 (16)0.20 (5)
1.50 (38)
1.18(30)
1/4-
20U
NC
-2B
3) 4
)
1/4-
20U
NC
-2B
3) 4
)
0.63 (16)
1.81 (45.9)
1.18 (30)
0.20 (5)
Usable shaft length
Usable shaft length
31/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
DGTwo-point control, directly operated, port plate 91
DGTwo-point control, directly operated, port plate 92
DRPressure control, port plate 91
DRPressure control, port plate 92
DRGPressure control, remotely operated, port plate 91
DRGPressure control, remotely operated, port plate 92
Details on connection options can be found on pages 29 and 30
Dimensions size 71 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
Z
L
0.12
(3)
(Ø25
)
0.98
1.00
DIA
+0.
4
9.55 (242.5)9.84 (250)
X
2.89(73.5)
L
7.91 (201)
0.12
(3)
(Ø25
)
0.98
1.00
DIA
+0.
4
5.02 (127.5)4.86 (123.5)
X
Z
S
BL
10.98 (279)
max
. 4.3
3 (1
10)
L
max
4.3
3 (1
10)
6.30 (160)
X
L
max
4.3
3 (1
10)
5.63 (143)6.30 (160)
1.57
(40
)
7.20(183)X
X
S
B
X
L
10.98 (279)
max
. 4.3
3 (1
10)
1.57
(40
)
10.31 (262)
X
3.62 (92)
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
to flange surface
to flange surface
to flange surface
View Z
View Z
View Z
(A)A10V(S)O Series 31 RA-A 92701/03.1232/52 Bosch Rexroth Corp.
Dimensions size 71DFLRPressure, flow and power control, port plate 91
DFLRPressure, flow and power control, port plate 92
ED7. / ER7.Electro-hydraulic pressure control, port plate 91
ED7. / ER7.Electro-hydraulic pressure control, port plate 92
ER7.: 12.36 in (314 mm) when using a sandwich plate pressure reducing valve.1)
ER7.: 7.68 in (195 mm) when using a sandwich plate pressure reducing valve.2)
For details of connection options and drive shafts, see also pages 21 and 22
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
L
9.53 (242)
5.63 (143)6.28 (159.5)
4.88
(124
)
X
1.57
(40)
X
L
max
. 4.3
3 (1
10)4.
06 (1
03)
5.43 (138)
2.72 (69)
4.88
(124
)
10.98 (279)
X1.93 (49)
6.30 (160)2)
5.55
(141
)
1.42 (36)7.91 (201)
L
X
Z
5.53
(140
.5)
1.42 (36)
2.89(73.5)
10.98 (279)1)
S
L
View Z
Valve mounting for ccw rotation see page 29
Valve mounting for ccw rotation Valve mounting for
ccw rotation
Valve mounting for ccw rotation
to flange surface to flange surface
33/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 100DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation
Details on connection options and shaft ends can be found on page 34
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
X
X
3.90 (99)
40 max
. 110
2.16
(55)
2.16
(55)
S
BX
2.00
(50.
8)
DIA 2.36(Ø60)
3.50(88.9)
2.63 (66.7)1.
25 (3
1.8
)
DIA 1.26 (Ø32)L
L1
11.34 (288)
13.54 (344)12.87 (327)
0.79 (20)3.74 (95)
6.89 (175)0.50 (12.7)0.24 (6)
DIA
1.2
6 (Ø
32)
2.63
(6
6.7)
1.25 (31.8)
B
S3.50
(88.
9)
DIA
2.3
6 (Ø
60)
2.00(50.8)
1.57
(40
)
5.84 (148.4)6.50 (165)12.48 (317)
3.94
(100
)3.
94 (1
00)
7.13 (181)8.27 (210)
4.65 (118)
0.69
(17.
5)5.
98 (1
52)
4.17 (1
06)
3.74
(95
)
W
V
Z
X
L1
0.24 (6)9.84 (250)
0.79 (20)
3.74 (95)10.83 (275)
6.89 (175)0.50 (12.7)
max
. 4.3
3 (1
10)
(Ø12
7
)
5.00
004.
9975
DIA
-0.0
630
(Ø12
7
)
5.00
004.
9975
DIA
-0.0
630
45°
Detail V Detail W
Flange ISO 3019-1
Flange ISO 3019-1
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Port plate 62
Port plate 61
(A)A10V(S)O Series 31 RA-A 92701/03.1234/52 Bosch Rexroth Corp.
Drive shaftS Splined shaft 1 1/2 in
17T 12/24DP1) (SAE J744)U Splined shaft 1 1/4 in
14T 12/24DP1) (SAE J744)W Splined shaft 1 1/4 in
14T 12/24DP1)2) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Spline according to ANSI B92.1a, run out of spline is a deviation from standard.2)
Thread according to ASME B1.13)
For the maximum tightening torques the general instructions on page 52 must be observed.4)
PortsDesignation Port for Standard Size5) Max. press.
[psi (bar)]6)State
B Service line, fastening thread
SAE J518 ASME B1.1
1 1/4 in 1/2-13 UNC-2B; 0.75 (19) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
2 1/2 in 1/2-13 UNC-2B; 0.87 (22) deep
145 (10) O
L Case drain fluid ISO 119267) 1 1/16-12 UNF-2B; 0.71 (18) deep 30 (2) O8)
L1 Case drain fluid ISO 119267) 1 1/16-12 UNF-2B; 0.71 (18) deep 30 (2) X8)
X Pilot pressure ISO 119267) 7/16-20 UNF-2B; 0.45 (11.5) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2287) G 1/4 in; 0.47 (12) deep 5100 (350) O
For the maximum tightening torques the general instructions on page 52 must be observed.5)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 6)
fittings. Pressure values in psi (bar) absolute.The spot face can be deeper than as specified in the standard.7)
Depending on the installation position, L or L8) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
Dimensions size 100 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
2.44 (61.9)
1.10 (28)
0.20 (5)
2.13 (54)
1.71(43.5)
7/16
-14U
NC
-2B
3) 4
)
2.18(55.4)
0.75 (19)0.20 (5)
1.87 (47.5)
1.38(35)
5/16
-18U
NC
-2B
3) 4
)
5/16
-18U
NC
-2B
3) 4
)
0.75 (19)
2.18 (55.4)
1.38 (35)
0.20 (5)
Usable shaft length
35/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
DGTwo-point control, directly operated, port plate 61
DGTwo-point control, directly operated, port plate 62
DRPressure control, port plate 61
DRPressure control, port plate 62
DRGPressure control, remotely operated, port plate 61
DRGPressure control, remotely operated, port plate 62
Details on connection options and shaft ends can be found on pages 33 and 34
Dimensions size 100 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
3.19 (81)
(Ø25
)0.
981.
00D
IA+
0.4
12.13 (308)12.40 (315)
X
0.12
(3) Z
10.55 (268)
(Ø25
)
0.98
1.00
DIA
+0.
4
0.12
(3)
5.06 (128.5)5.22 (132.5)
X
Z
max
. 4.3
3 (1
10)
13.54 (344)
X
6.50 (165) max
. 4.3
3 (1
10)
X
Z
3.90 (99)
1.57
(40
)m
ax. 4
.33
(110
)
X13.54 (344)
12.87 (327)
X
1.57
(40
)
5.83 (148)6.50 (165)
X
9.84 (250)
max
. 4.3
3 (1
10)
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
to flange surface
to flange surface
to flange surface
View Z
View Z
View Z
(A)A10V(S)O Series 31 RA-A 92701/03.1236/52 Bosch Rexroth Corp.
DFLRPressure, flow and power control, port plate 61
DFLRPressure, flow and power control, port plate 62
ED7./ER7.Electro-hydraulic pressure control, port plate 61
ED7./ER7.Electro-hydraulic pressure control, port plate 62
ER7.: 14.92 in (379 mm) when using a sandwich plate pressure reducing valve. 1)
ER7.: 7.87 in (200 mm) when using a sandwich plate pressure reducing valve.2)
Details on connection options and shaft ends can be found on pages 33 and 34
Dimensions size 100 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
X1.89 (49)
5.72(145.3)
5.08
(129
)
13.54 (344)
4.27
(108
.5)
4.37 (111) Xm
ax. 4
.33
(110
)
5.83 (148)
1.57
(40
)
6.48 (164.5)
5.08
(129
)X12.12 (308)
13.54 (344)1)
5.51
(140
)
4.60 (117)
X
Z
5.51
(140
)
6.50 (165)2)X
1.40 (35.6)
10.55 (268)
View Z
Valve mounting for ccw rotation see page 33
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
37/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions size 140DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation, mounting flange D
Details on connection options and shaft ends can be found on page 39
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
L
L
SB
4.33
(110
)4.
33 (1
10)
10.83 (275)
6.36
(161
.6)
7.87
(200
)
5.16 (131)
0.81 (20.6)
V
W
45°
0.83 (21)3.07 (78)
(Ø15
2.4
)
6.00
005.
9975
DIA
-0.0
630
(Ø15
2.4
)
6.00
005.
9975
DIA
-0.0
630
X
L1
L L
12.48 (317)
8.74 (222)
4.66 (118
.5)
4.96
126
)
7.20 (183)8.23 (209)
4.41
(112
)1.
02 (2
6)
4.25
(108
)
6.36 (161.6)7.87 (200)
6.81 (173)0.50 (12.7)
0.25 (6.4)
B
S
Z
L1
X
2.00
(50.
8)1.
25(3
1.8
)2.
36(6
0)
2.36
(60
)
4.92
(125
)
11.53 (293)13.90 (353)
14.92 (379)
DIA 1.26 (Ø32)2.63 (66.7)
DIA 2.48 (Ø63)88.9
5.51 (140)
1.02
(26
)
0.83 (21) 3.07(78)
0.25 (6.4)
0.50 (12.7)
6.81 (173)
S
2.00(50.8)D
IA 2
.48
(Ø63
)3.
50 (8
8.9
)
B
DIA
1.2
6(Ø
32)
2.63
(66.
7)
1.25(31.8)
Detail V
Port plate 62
Port plate 61
Detail W
Flange 3019-1
Flange 3019-1
Valve mounting for ccw rotation
Valve mounting for ccw rotation
(A)A10V(S)O Series 31 RA-A 92701/03.1238/52 Bosch Rexroth Corp.
Dimensions size 140DFR/DFR1 – Pressure and flow control, hydraulic Clockwise rotation, mounting flange C
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
SB
Z
B
S
X
2.00
(50.
8)1.
25 (3
1.8
)2.
36(6
0)
2.36
(60
)
DIA 1.26 (Ø32)2.62 (66.7)
DIA 2.48 (Ø63)3.50 (88.9)
5.51 (140)
XL
L1
7.20 (183)8.23 (209)
1.02
(26
)4.
96 (1
26)
9.78 (248.5)
(Ø12
7
)
5.00
004.
9975
DIA
-0.0
630
(Ø12
7
)
5.00
004.
9975
DIA
-0.0
630
7.83 (199)0.24 (6)0.50 (12.7)
11.85 (301)4.09 (104)
0.79 (20)
13.50 (343)
0.69
(17.
5)5.
98 (1
52)
8.27 (210)7.12 (181)
5.16 (131)
4.41
(112
)4.
25 (1
08)
45°
4.33
(110
)4.
33 (1
10)
S
BV
W
X
L
L1
14.92 (379)7.83 (199)0.24 (6)
0.50 (12.7)
12.56 (319)4.09 (104)
0.79 (20)
15.94 (405)
4.92
(125
)
1.02
(26
)
S2.00 (50.8)
DIA
2.4
8(Ø
63)
3.50
(88.
9)
B
DIA
1.2
6(Ø
32)
66.7
1.25 (31.8)
4.67 (1
18.5)
Detail V Detail W
Flange 3019-1
Flange 3019-1
Port plate 62
Port plate 61
Valve mounting for ccw rotation
Valve mounting for ccw rotation
39/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Drive shaftS Splined shaft 1 3/4 in
13T 8/16DP1) (SAE J744)
ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 51)
Thread according to ASME B1.12)
For the maximum tightening torques the general instructions on page 52 must be observed.3)
PortsDesignation Port for Standard Size4) Max. press.
[psi (bar)]5)State
B Service line, fastening thread
SAE J518 ASME B1.1
1 1/4 in 1/2-13 UNC-2B; 0.94 (24) deep
5100 (350) O
S Suction line, fastening thread
SAE J518 ASME B1.1
2 1/2 in 1/2-13 UNC-2B; 0.94 (24) deep
145 (10) O
L Case drain fluid ISO 119266) 1 1/16-12 UNF-2B; 0.71 (18) deep 30 (2) O7)
L1 Case drain fluid ISO 119266) 1 1/16-12 UNF-2B; 0.71 (18) deep 30 (2) X7)
X Pilot pressure ISO 119266) 9/16-18UNF-2B; 0.51 (13) deep 5100 (350) O
X Pilot pressure with DG-control DIN ISO 2286) M14 x 1.5; 12 deep 5100 (350) O
MH Gauge port, high pressure DIN 3852 M14 x 1.5, 12 deep 5100 (350) X
For the maximum tightening torques the general instructions on page 52 must be observed.4)
Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and 5)
fittings. Pressure values in psi (bar) absolute.The spot face can be deeper than as specified in the standard.6)
Depending on the installation position, L or L7) 1 must be connected (see also installation instructions on pages 48, 49)O = Must be connected (plugged on delivery) X = Plugged (in normal operation)
Dimensions size 140 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
2.95 (75)
1.26 (32)0.20 (5)
2.64 (67)
2.09 (53)
1/2-
13U
NC
-2B
2) 3
)
(A)A10V(S)O Series 31 RA-A 92701/03.1240/52 Bosch Rexroth Corp.
DGTwo-point control, directly operated, port plate 61
DGTwo-point control, directly operated, port plate 62
DRPressure control, port plate 61
DRPressure control, port plate 62
DRGPressure control, remotely operated, port plate 61
DRGPressure control, remotely operated, port plate 62
Details on connection options can be found on pages 37, 38 and 39
Dimensions size 140 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
Z
L
S
B
3.70 (94)MH
X
0.10
(2.6
)1.1
0 (2
8)
12.68 (322)12.87 (327)
Z
S
BL
13.35 (339)
4.96
(126
)
Z
L
S
B
5.51 (140)
12.32 (313)13.35 (339)
1.02
(26
)4.
96 (1
26)
X
L
1.10
(28
)
6.02 (153)6.22 (158)
MH
X
0.10
(2.6
)
10.55 (268)
L
6.70 (170)
1.02
(26
)4.
96 (1
26)
L
4.96
(126
)2.
20 (5
6)
12.36 (314)X
6.69 (170)5.67 (144)
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation Valve mounting for
ccw rotation
Valve mounting for ccw rotation
to flange surface
to flange surface
to flange surface
to flange surface
to flange surface
View Z
View Z
View Z
41/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
DFLRPressure, flow and power control, port plate 61
DFLRPressure, flow and power control, port plate 62
ED7. / ER7.Electro-hydraulic pressure control, port plate 61
ED7. / ER7.Electro-hydraulic pressure control, port plate 62
ER7.: 15.12 in (384 mm) when using a sandwich plate pressure reducing valve.1)
ER7.: 8.43 in (214 mm) when using a sandwich plate pressure reducing valve.2)
Details on connection options can be found on pages 37, 38 and 39
Dimensions size 140 Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
L
3.90 (99) 1.93 (49)
14.92 (379)
5.51
(140
)
6.42 (163)
4.68
(119
) X
4.96
(126
)
L
5.51
(140
)
X
12.36 (314)
4.25
(10
8)
2.20
(56
)
7.20 (183)8.23 (209)
L
X
7.05 (179)2)
5.07
(128
.9)
1.40 (35.6)
13.74 (349)1)
4.88
(124
)
1.20 (130.6)
X
Z
Valve mounting for ccw rotation
Valve mounting for ccw rotation
Valve mounting for ccw rotation
to flange surface
View Z
Valve mounting for ccw rotation see page 38
(A)A10V(S)O Series 31 RA-A 92701/03.1242/52 Bosch Rexroth Corp.
Dimensions through driveK01 flange ISO 3019-2 (SAE J744 - 82-2 (A)) Coupling for splined shaft according to ANSI B92.1a-1996 5/8 in 9T 16/32 DP1) (SAE J744 - 16-4 (A))
K52 flange ISO 3019-2 (SAE J744 - 82-2 (A)) Coupling for splined shaft according to ANSI B92.1a-1996 3/4 in 11T 16/32 DP1) (SAE J744 - 19-4 (A-B))
K68 flange ISO 3019-2 (SAE J744 - 101-2 (B)) Coupling for splined shaft according to ANSI B92.1a-1996 7/8 in 13T 16/32 DP1) (SAE J744 - 22-4 (B))
NG A1 A2 A3 A42)
18 7.16 (182)
0.39 (10)
1.70 (43.3)
M10 x 1.5, 0.57 (14.5) deep
28 8.03 (204)
0.39 (10)
1.33 (33.7)
M10 x 1.5, 0.63 (16) deep
45 9.02 (229)
0.42 (10.7)
2.10 (53.4)
M10 x 1.5, 0.63 (16) deep
71 10.51 (267)
0.46 (11.8)
2.41 (61.3)
M10 x 1.5, 0.79 (20) deep
100 13.31 (338)
0.41 (10.5)
2.56 (65)
M10 x 1.5, 0.63 (16) deep
1401) 13.78 (350)
0.43 (10.8)
3.04 (77.3)
M10 x 1.5, 0.63 (16) deep
D-flange only1)
NG A1 A2 A3 A42)
18 7.16 (182)
0.74 (18.8)
1.52 (38.7)
M10 x 1.5, 0.57 (14.5) deep
28 8.03 (204)
0.74 (18.8)
1.52 (38.7)
M10 x 1.5, 0.63 (16) deep
45 9.02 (229)
0.744 (18.9)
1.52 (38.7)
M10 x 1.5, 0.63 (16) deep
71 10.51 (267)
0.84 (21.3)
1.63 (41.4)
M10 x 1.5, 0.79 (20) deep
100 13.31 (338)
0.75 (19)
1.53 (38.9)
M10 x 1.5, 0.63 (16) deep
1401) 13.78 (350)
0.744 (18.9)
1.52 (38.6)
M10 x 1.5, 0.63 (16) deep
D-flange only1)
NG A1 A2 A3 A42)
28 8.03 (204)
0.70 (17.8)
1.64 (41.7)
M12 x 1.75, continuous
45 9.02 (229)
0.704 (17.9)
1.64 (41.7)
M12 x 1.75, 0.71 (18) deep
71 10.51 (267)
0.80 (20.3)
1.74 (44.1)
M12 x 1.75, 0.79 (20) deep
100 13.31 (338)
0.71 (18)
1.65 (41.9)
M12 x 1.75, 0.79 (20) deep
1401) 13.78 (350)
0.70 (17.8)
1.64 (41.6)
M12 x 1.75, 0.79 (20) deep
D-flange only1)
30° pressure angle, flat root, side fit, tolerance class 51)
Thread according to DIN 13, observe the general instructions on page 52 for the maximum tightening torques.2)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
45°
B
A
0.39(10)
(Ø82
.55
)
DIA
3.25
203.
2508
+0.
050
–0.0
20
A4
A3A2
A1
DIA 4.19
(Ø106.5)
45°
B
A
A4
A3
A2A1
(Ø82
.55
)D
IA3.
2520
3.25
08 +0.
05–0
.02
0.39(10)
DIA 4.19
(Ø106.5)
A
B
A4
45°
(Ø10
1.6
)
DIA
4.00
204.
0008
+0.
05–0
.02
A2A1
A30.39(10)
DIA 5.75
(Ø146)
Cut A - B
Cut A - B
Cut A - B
omitted for NG28
omitted for NG28
to mounting flange
to mounting flange
to mounting flange
43/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Dimensions through driveK04 flange ISO 3019-2 (SAE J744 - 101-2 (B)) Coupling for splined shaft according to ANSI B92.1a-1996 1 in 15T 16/32 DP1) (SAE J744 - 25-4 (B-B))
K07 flange ISO 3019-2 (SAE J744 - 127-2 (C)) Coupling for splined shaft according to ANSI B92.1a-1996 1 1/4 in 14T 12/24 DP1) (SAE J744 - 32-4 (C))
K24 flange ISO 3019-2 (SAE J744 - 127-2 (C)) Coupling for splined shaft according to ANSI B92.1a-1996 1 1/2 in 17T 12/24 DP1) (SAE J744 - 38-4 (C-C))
NG A1 A2 A3 A42)
71 10.51 (267)
0.86 (21.8)
2.31 (58.6)
M16 x 2, continuous
100 13.31 (338)
0.77 (19.5)
2.22 (56.4)
M16 x 2, continuous
1401) 13.78 (350)
0.76 (19.3)
2.21 (56.1)
M16 x 2, 0.94 (24) deep
D-flange only1)
NG A1 A2 A33) A3a
4) A42)
100 13.31 (338)
0.41 (10.5)
2.56 (65)
– (–)
M16 x 2, continuous
1401) 13.78 (350)
0.42 (10.8)
2.95 (75)
– (–)
M16 x 2, 0.94 (24) deep
13.78 (350)
0.40 (10.3)
– (–)
2.72 (69.1)
M16 x 2, 0.94 (24) deep
D-flange only1)
NG A1 A2 A3 A42)
45 9.02 (229)
0.724 (18.4)
1.84 (46.7)
M12 x 1.75, 0.71 (18) deep
71 10.51 (267)
0.82 (20.8)
1.93 (49.1)
M12 x 1.75, 0.79 (20) deep
100 13.31 (338)
0.716 (18.2)
1.83 (46.6)
M12 x 1.75, 0.79 (20) deep
1401) 13.78 (350)
0.72 (18.3)
1.81 (45.9)
M12 x 1.75, 0.79 (20) deep
D-flange only 1)
30° pressure angle, flat root, side fit, tolerance class 51)
Thread according to DIN 13, observe the general instructions on page 52 for the maximum tightening torques.2)
Coupling 3) without stopCoupling 4) with stop
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
A
B
A4
45°
(Ø10
1.6
)
DIA
4.00
204.
0008
+0.
05–0
.02
A2A1
A30.39(10)
5.75
(Ø146)
45°A
B
(Ø12
7
)
DIA
5.00
205.
0008
+0.
05–0
.02
A2A1
A3
A4
0.51(13)
DIA 7.12
(Ø181)
45°A
B
A2A1
A3
A4
A3a
0.51(13)
Ø12
7D
IA5.
0020
5.00
08+
0.05
–0.0
2
DIA 7.12
(Ø181)
Cut A - B
Cut A - B
Cut A - B
omitted for NG71
omitted for NG71
to mounting flange
to mounting flange
to mounting flange
(A)A10V(S)O Series 31 RA-A 92701/03.1244/52 Bosch Rexroth Corp.
Dimensions through driveK17 flange ISO 3019-2 (SAE J744 - 152-4 (A)) Coupling for splined shaft according to ANSI B92.1a-1996 1 3/4 in 13T 8/16 DP1) (SAE J744 - 44-4 (D))
NG A1 A2 A3 A42)
1401) 13.78 (350)
0.43 (11)
3.04 (77.3)
M16 x 2, continuous
D-flange only1)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
A
B A2A1
A4
A30.51(13)
DIA
6.00
276.
0008
(Ø15
2.4
)+
0.07
–0.0
2
6.36
(161
.6)
6.36 (161.6)
30° pressure angle, flat root, side fit, tolerance class 51)
Thread according to DIN 13, observe the general instructions on page 52 for the maximum tightening torques.2)
Cut A - B
to mounting flange
45/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
SAE – mounting flangeThrough-drive1) Mounting option – 2nd pumpFlange ISO 3019-1
Coupling for splined shaft
Short des.
A10VO/31 NG (shaft)
A10V(S)O/5x NG (shaft)
External gear pump design (NG)
Through drive available for NG
82-2 (A) 5/8 in K01 18 (U) 10 (U) F (5 to 22) 18 to 140
3/4 in K52 18 (S, R) 10 (S) 18 (U) 18 (S, R)
– 18 to 140
101-2 (B) 7/8 in K68 28 (S, R) 45 (U, W)1)
28 (S, R) 45 (U, W)1)
N/G (26 to 49) 28 to 140
1 in K04 45 (S, R) –
45 (S, R) 60, 63 (U, W) 2)
– 45 to 140
127-2 (C) 1 1/4 in K07 71 (S, R) 100 (U)3)
85 (U, W)3) 100 (U, W)
– 71 to 140
1 1/2 in K24 100 (S) 85 (S) 100 (S)
– 100 to 140
152-4 (4-hole D)
1 3/4 in K17 140 (S) – – 140
Not for main pump NG28 with K681)
Not for main pump NG45 with K042)
Not for main pump NG71 with K073)
Summary mounting options
(A)A10V(S)O Series 31 RA-A 92701/03.1246/52 Bosch Rexroth Corp.
Combination pumps A10VO + A10VOWhen using combination pumps it is possible to have multiple, mutually independent circuits without the need for a splitter gearbox.
When ordering combination pumps the model codes for the first and the second pump must be joined by a "+".
Order example: A10VSO100DFR1/31R-VSB12K04+ A10VSO45DFR/31R-VSA12N00
If no further pumps are to be factory-mounted, the simple type code is sufficient.
It is permissible to use a combination of two single pumps of the same size (tandem pump), considering a dynamic mass accele-ration force of maximum 10 g (= 98.1 m/s2) without an additional support bracket.
Each through drive is plugged with a non-pressure-resistant cover. Before commissioning the units, they must therefore be equipped with a pressure-resistant cover. Through drives can also be ordered with pressure-resistant covers. Please specify in clear text.
For combination pumps comprising more than two pumps, the mounting flange must be calculated for the permissible moment of inertia.
Permissible mass moment of inertia
NG 18 28 45 71 100 140
Permissible moment of inertia
static Tm lb-ft (Nm)
lb-ft (Nm)
369 (500)
649 (880)
1010 (1370)
1593 (2160)
2213 (3000)
33191) (4500)1)
22132) (3000)2)
dynamic at 10 g (98.1 m/s2) Tm lb-ft (Nm)
lb-ft (Nm)
37 (50)
65 (88)
101 (137)
159 (216)
221 (300)
332 1) (450)1)
1322) (300)2)
Mass with through-drive plate Mass without through drive (e.g. 2nd pump)
m
m
lbs (kg)
lbs (kg)
30.8 (14)
26.5 (12)
41.9 (19)
33 (15)
55.1 (25)
46 (21)
86 (39)
73 (33)
119 (54)
99 (45)
150 (68)
132 (60)
Distance center of gravity l in (mm)
3.54 (90)
4.33 (110)
5.12 (130)
5.91 (150)
6.30 (160)
6.30 (160)
4-hole flange (D)1)
2-hole flange (C)2)
m1, m2, m3 Mass of pumps [lbs (kg)]
l1, l2, l3 Distance center of gravity [in (mm)]
Tm = (m1 • l1 + m2 • l2 + m3 • l3) • 1
12 (102) [lb-ft (Nm)]
l1l2
m1m2 m3
l3
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
47/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Connector for solenoidsDEUTSCH DT04-2P-EP04, 2-pinMolded, without bidirectional suppressor diode ___________ P
The following type of protection is provided with installed mating connector:
IP67 ___________________________________DIN/EN 60529 and IP69K _______________________________ DIN 40050-9
Circuit symbol
Without bidirectional suppressor diode
Mating connector
DEUTSCH DT06-2S-EP04 Bosch Rexroth Mat. No. R902601804
Consisting of: DT designation
1 case – _______________________________DT06-2S-EP04
1 wedge – _______________________________________W2S
2 sockets – ____________________________ 0462-201-16141
The mating connector is not included in the delivery contents. This can be supplied by Bosch Rexroth on request.
Changing connector position
If necessary, you can change the position of the connector by turning the solenoid.
To do this, proceed as follows:
1. Loosen the mounting nut (1) of the solenoid. To do this, turn the mounting nut (1) one revolution counter-clockwise.
2. Turn the solenoid body (2) to the desired position.
3. Retighten the mounting nut of the solenoid. Tightening torque: 4 +0.7 lb-ft (5+1 Nm) (size WAF 26, 12-pt DIN 3124).
On delivery, the position of the connector may differ from that shown in the brochure or drawing.
1.44
(36.
7)
(2)(1)
1.44 (36.7)
2.70 (68.5)
DIA
1.4
6(Ø
37)
1.97 (50)
Before finalizing your design request a certified installation drawing. Dimensions in inches and (mm).
(A)A10V(S)O Series 31 RA-A 92701/03.1248/52 Bosch Rexroth Corp.
Installation instructionsGeneral
The axial piston unit must be filled with hydraulic fluid and air bled during commissioning and operation. This must also be observed following a longer standstill as the axial piston unit empty via the hydraulic lines.
Particularly with the "drive shaft up/down" installation position, filling and air bleeding must be carried out completely as there is, for example, a danger of dry running.
The case drain fluid in the motor housing must be directed to the reservoir via the highest case drain port (L1, L2, L3).
For combinations of multiple units, make sure that the respec-tive case pressure in each unit is not exceeded. In the event of pressure differences at the case drain ports of the units, the shared case drain line must be changed so that the minimum permissible case pressure of all connected units is not excee-ded in any situation. If this is not possible, separate case drain lines must be laid if necessary.
To achieve favorable noise values, decouple all connecting lines using elastic elements and avoid above-reservoir installa-tion.
In all operating conditions, the suction line and case drain line must flow into the reservoir below the minimum fluid level . The permissible suction height hS is a result of the overall pressure loss, but may not be greater than hS max = 31.50 in (800 mm). The minimum suction pressure at port S must also not fall below 12 psi (0.8 bar) absolute during operation.
Installation position
See the following examples 1 to 12. Additional installation positions are available upon request.
Recommended installation positions: 1 and 3.
Note
You can expect certain installation positions to affect the –control device. Because of gravity, unit weight and case pressure, minor characteristic displacements and response time changes may occur.
Below-reservoir installation (standard)
Below-reservoir installation means the axial piston unit is ins-talled outside of the reservoir below the minimum fluid level.
1 2
3 4
Installation position Air bleed Filling
1 L S + L1
2 L1 S + L
3 L1 S + L
4 L S + L1
Key, see page 49.
L
L1S
ht min
SB
a min
a min a min
L
L1 S
ht min
SB
L L1S
ht min
SB
LL1
S
h min
h min h min
ht min
SB
a min
h min
49/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Installation instructionsInside-reservoir installation
Inside-reservoir installation is when the axial piston unit is installed in the reservoir below the minimum fluid level. The axial piston unit is completely below the hydraulic fluid.
If the minimum fluid level is equal to or below the upper edge of the pump, see chapter "Above-reservoir installation".
Axial piston units with electrical components (e.g. electric cont-rol, sensors) may not be installed in a reservoir below the fluid level.
9 10
11 12
Installation position Air bleed Filling
9 L L, L1
10 L1 L, L1
11 L1 S + L, L1
12 L S + L, L1
S Suction port
F Filling / air bleeding
L, L1 Case drain port
SB Baffle (baffle plate)
ht min Minimum necessary immersion depth (7.87 in (200 mm))
hmin
hES min
Minimum necessary spacing to reservoir bottom (3.94 in (100 mm))
Minimum necessary height needed to protect the axial piston unit from draining (0.98 in (25 mm)).
hS max Maximum permissible suction height (31.50 in (800 mm))
amin When designing the reservoir, ensure adequate distance between the suction line and the case drain line. This prevents the heated, return flow from being drawn directly back into the suction line.
Above-reservoir installation
Above-reservoir installation means the axial piston unit is installed above the minimum fluid level of the reservoir. To prevent the axial piston unit from draining, a height difference hES min of at least 0.98 in (25 mm) at port L 1 is required in installation position 6.
Observe the maximum permissible suction height hS max = 31.50 in (800 mm).
A check valve in the case drain line is only permissible in individual cases. Consult us for approval.
5 6
7 8
Installation position Air bleed Filling
5 F L (F)
6 F L1 (F)
7 F S + L 1 (F)
8 F S + L (F)
L
L1S
F
hs max
ht min
a min
SB
S
F
L L1
L
L1S
F
S
F
LL1
h min
hs max
hES min
hs max
ht min
a min
SB
h min
hs max
ht min
a min
SB
h min
ht min
a min
SB
h min
L
L1S
ht min
h min
ht min
h min
a min
a min
a min
a min
SB SB
SB SB
L
L1 S
LL1
S
LL1
Sht min
h min
ht min
h min
(A)A10V(S)O Series 31 RA-A 92701/03.1250/52 Bosch Rexroth Corp.
Notes
51/52Bosch Rexroth Corp.RA-A 92701/03.12 (A) A10V(S)O Series 31
Notes
(A)A10V(S)O Series 31 RA-A 92701/03.1252/52 Bosch Rexroth Corp.
© Bosch Rexroth Corporation
All rights reserved. Neither this document, nor any part of it, may be reproduced, duplicated, circulated or disseminated, whether by copy, electronic format or any other means, without the prior consent and authorization of Bosch Rexroth Corp.
The data and illustrations in this brochure/data sheet are intended only to descri-be or depict the products. No representation or warranty, either express or im-plied, relating to merchantability or fitness for intended use, is given or intended by virtue of the information contained in this brochure/data sheet. The information contained in this brochure/data sheet in no way relieves the user of its obligation to insure the proper use of the products for a specific use or application. All products contained in this brochure/data sheet are subject to normal wear and tear from usage.
Subject to change.
Bosch Rexroth CorporationMobile Applications8 Southchase CourtFountain Inn, SC 29644-9018 USATelephone (864) 967-2777Facsimile (864) 967-8900www.boschrexroth-us.com
Bosch Rexroth CorporationIndustrial Applications2315 City Lane RoadBethlehem, PA 18017-2131 USATelephone (610) 694-8300Facsimile (610) 694-8467www.boschrexroth-us.com
General instructionsThe A10VO / A10VSO pump is designed to be used in open circuit. –
Project planning, installation and commissioning of the axial piston unit – require the involvement of qualified personnel.
Before operating the axial piston unit, please read the appropriate instruction manual thoroughly and completely. If necessary, request these –from Bosch Rexroth.
During and shortly after operation, there is a risk of burns on the axial piston unit and especially on the solenoids. –Take appropriate safety measures (e.g. by wearing protective clothing).
Depending on the operating conditions of the axial piston unit (operating pressure, fluid temperature), the characteristics may shift. –
Service line ports: –
The ports and fastening threads are designed for the specified maximum pressure. The machine or system manufacturer must ensure that -the connecting elements and lines correspond to the specified application conditions (pressure, flow, hydraulic fluid, temperature) with the necessary safety factors.
The service line ports and function ports are only designed to accommodate hydraulic lines. -
Pressure cut-off and pressure control do not provide security against pressure overload. A separate pressure relief valve is to –be provided in the hydraulic system.
The data and notes contained herein must be adhered to. –
The product is not approved as a component for the safety concept of a general machine according to ISO 13849. –
The following tightening torques apply: –
Fittings: -Observe the manufacturer‘s instruction regarding the tightening torques of the used fittings.
Mounting bolts: -For mounting bolts with metric ISO thread according to DIN 13 or thread according to ASME B1.1, we recommend checking the tightening torque individually according to VDI 2230.
Female threads in axial piston unit: -The maximum permissible tightening torques MG max are maximum values for the female threads and must not be exceeded. For values, see the following table.
Threaded plugs: -For the metal threaded plugs supplied with the axial piston unit, the required tightening torques of the threaded plugs MV apply. For values, see the following table.
Ports Maximum permissible tightening torque for female threads MG max
Required tightening torque for threaded plugs MV
Size of hexagon socket of threaded plugs
Standard Thread size
ISO 11926 7/16-20 UNF-2B 40 Nm 18 Nm 3/16 in
3/4-16 UNF-2B 160 Nm 70 Nm 5/16 in
9/16-18 UNF-2B 80 Nm 35 Nm 1/4 in
7/8-14 UNF-2B 240 Nm 110 Nm 3/8 in
1 1/16-12 UNF-2B 360 Nm 170 Nm 9/16 in
DIN 3852 M14 x 1.5 80 Nm 45 Nm1) 6 mm
DIN ISO 228 G 1/4 in 70 Nm – –
The tightening torques of the threaded plugs M1) V apply for screws in the "dry" state as received on delivery and in the "lightly oiled" state for installation