![Page 1: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/1.jpg)
A Differential Planetary Gear Model with Backlash and Teeth Damage
Xi Wu, Jim Meagher, Andrew Sommer
ABSTRACT
Planetary gear trains can be more compact and efficient as power transmissions than fixed axis gear trains
but are also more complicated and less understood in terms of vibration health monitoring. A practical differential
planetary gear train, which combines two inputs and one output, is studied using multi-body dynamics software.
Backlash between the sun gear and planet gears are precisely specified to avoid teeth interference and undercut. In
order to calculate accurate impact forces, an impact model is chosen. Tooth geometry errors are created on the sun
gear. Constraints and contact forces to the model are applied as close as possible to real operating conditions.
Torsional vibration induced by backlash and tooth geometry errors is shown to cause teeth separation and double-
sided impacts in unloaded and lightly loaded gearing drives. Planetary gears with only backlash errors are compared
to those containing both backlash and tooth defects under different kinematic and loading conditions. Time domain
results show that the dynamic responses due to the combination of backlash and tooth defects depend on the
interaction of many components of the differential planetary system.
1. Introduction
The planetary gear train is widely used in transmission design of automobiles, helicopters and aircraft
engines due to the numerous advantages over traditional fixed-axis gear transmissions. Since the load being
transmitted is shared between several planets, torque capability is significantly increased. One notable advantage of
a planetary gear is its distinctive combination of both compactness and magnificent power transmission efficiencies.
Despite the above advantages, however, the complicated dynamic forces existing among sun, planet and ring gears
are difficult to analyze for the main sources of the vibration. Reasonably simulating the practical dynamic force
between single-mating-gear pair still remains as an important topic. Needless to say, it is even more challenging to
realistically model a planetary gear train with multiple meshing stages. As a result, the dynamic analyses of
planetary gear trains have received far less attention than fixed-axis gear trains.
The earliest review papers that discuss the numerical modeling of gear dynamics focus on spur gears:
Özgüven and Houser in 1988 [1] and by Parey and Tandon in 2003 [2]. The models had a limited number of degrees
of freedom and most commonly did not include tooth defects. Tooth meshing stiffness was characterized as either an
average or piecewise linear variation instead of the highly nonlinear Hertzian contact. Parey and Tandon’s review
did include spur gear defects. Parey etc. [3] developed a six DOF nonlinear model for a pair of spur gears on two
shafts, calculated the Hertzian stiffness for the tooth surface contact, and implemented the empirical mode
decomposition (EMD) method to simulate the different defect widths. The above research is based on fix-axis gears.
Lin and Parker [4] analytically investigate the parametric instability of planetary gears induced by gear
mesh stiffness variation. The authors use rectangular waveforms with different contact ratios and mesh phasing to
simulate the gear mesh stiffnesses existing between sun-planet and planet-ring gear mating pairs. Instability
boundaries are directly associated with meshing parameters in the vibration modes. The authors also demonstrate
some numerical simulation results about the teeth separation caused by parametric instability and strong impact in
the system response. Lin and Parker [5] derive a theoretical model and carefully identify the important
characteristics of the natural frequencies and vibration modes for planetary gears. The model uses three planar
degrees of freedom for each component of the planetary gears and takes gyroscopic effects and time-varying gear
mesh stiffnesses into consideration. The authors do comprehensive investigations about the distinctive
characteristics of each type of mode. Based on the model of reference [5], Guo and Parker [6] extended the two-
dimensional lumped-parameter model by incorporating the factors of teeth separation, back-side contact, tooth
wedging, and bearing clearances. By scrutinizing the dynamic response of an example planetary gear, the authors
investigate the nonlinear tooth wedging behavior often observed on a wind turbine planetary gear train. More
brought to you by COREView metadata, citation and similar papers at core.ac.uk
provided by DigitalCommons@CalPoly
![Page 2: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/2.jpg)
research about dynamic behavior of planetary gears can be found in reference [7, 8]. Unfortunately, the majority of
current papers about planetary gears does not include the interactive effects of backlash and gear teeth damage.
Although simplified model for even a one-stage gear train involves sophisticated mathematics, it cannot
accurately simulate the gear train’s practical dynamic behavior even for an ideal system by simply assuming time-
varying gear mesh stiffness as square waveforms. The impact forces between the mating pairs are very sensitive to
the geometric profile of gear tooth and the gear backlash which must be carefully designed. Geometric
simplifications can be overcome by combining CAD models with ADAMS. Kong and Meagher etc. [9] modeled the
nonlinear contact mechanics of large gearbox in that way but backlash was not included.
In this study, a practical differential planetary gear train, which combines two inputs and one output, is
studied using multi-body dynamics software. The backlash between the sun gear and planet gears are carefully
designed and calculated to avoid teeth interference and undercut. Tooth profile errors are introduced for comparison
to ideal gears. The nonlinear contact mechanics model of the meshing teeth is built by careful calculation and
selection of the contact simulation parameters such as the stiffness, force exponent, and damping and friction
coefficients. Planetary gears with only backlash errors are compared to those containing both backlash and tooth
defects under different kinematic and loading conditions. Time domain results will show that the dynamic responses
due to the combination of backlash and tooth defects depend on the interaction of many components of the
differential planetary system.
2. Modeling a differential planetary gear train with backlash and teeth damage
The differential planetary gear chosen for study has two inputs and one output [11, 12, 13]. The
transmission schematic and CAD model are shown in Fig. 1 (a), and Fig. 1 (b), respectively. The profile of the
"chipped" sun gear tooth in shown in Fig.2. Geometric parameters of the planetary gear train are shown in Table 1.
Combined with gear profile errors, the backlash may cause the loss of contact between gear teeth. This may
induce large impact forces associated with consecutive single-sided and/or double-sided impacts. The contact
surfaces between the gears are modeled as deformable flex-bodies. The nonlinear contact force, = K(d)e — cv , is
composed of an elastic and damping portion [10]. d is the penetration depth. The damping force, cv, is proportional
to impact velocity, v. The stiffness coefficient, K, is taken to be the average value of stiffness over one tooth mesh
cycle. The force exponent, e, was determined from trial simulations. The damping coefficient generally takes a
numeric value between 0.1%-1% of K. The determination of force exponents however is not obvious and must be
based on experience.
The MSC.ADAMS IMPACT algorithm was chosen as the contact force model because of its robustness in
numerical integration. The restitution model is extremely sensitive to the duration of the contact event, and is best
suited for impulse type simulations. It is not ideal for time histories that include a large number of contact events in
which the force vector is not known beforehand. The stiffness parameter is reasonable for this lightly loaded steel
gear pair, and was determined via a trial and error method. The response of interest occurs over a very short time
interval, around one hundred milliseconds. Because the damping force in meshing gears is such a small percentage
of K, its affect on the simulation results is not significant. Therefore, the damping coefficient is kept as near to zero
as possible to simplify the numerical solver routine. Penetration depth is defined here as the depth at which the
damping force becomes active. Similarly, modification of this value does not have a significant effect on response of
either gear. The MSC.ADAMS contact parameters are shown in Table 1. For ease of comparison, the dynamic
conditions of each figure are shown in Table 2.
3. Dynamic response and discussion of a planetary gear with the ring gear fixed
When ring gear b and gear 1 are fixed, an initial angular velocity ωx0 = 100 rad/sec is
applied on the carrier x. The carrier and sun gear are rotating in the same direction. By inspection of Fig.3, the
planets must be rotating in the opposite direction of both the sun and carrier. The responses of the planet gears are
nearly identical. This is expected because their axes are moving with the rotating carrier, and therefore make contact
with both the sun and ring at nearly the same instant.
![Page 3: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/3.jpg)
Consider the situation in Fig.4 when two or more planets experience nearly identical forces. This occurs
when they are both in contact with a given element, either the sun or ring, and are "sharing" the load. Each planet
gear is given an arbitrary designation of either 1, 2 , or 3, respectively. Between 5 and 15ms planet 1 is the only
planet in contact with the sun, therefore both planet1 and planet 3 are traveling within their respective backlash.
During this same interval, planet1 is not in contact with the ring. The MSC.ADAMS simulation model includes six
contact forces: three on the sun gear from each planet, and three on the ring gear from each planet. At any instant in
time, no force or any combination of all six forces are potentially active. Due to the small damping prescribed in the
contact force, this pattern will completely die out after a significant amount of time has passed. The pattern enclosed
shown between 0 and 30 ms continuously repeats with slightly less magnitude on each repetition.
A near equilibrium position is utilized in all presented simulations. First, consider the situation when the
transmission is in an exactly symmetrical position. The front and right planes of the sun and ring would be
coincident, and their top planes parallel. Each of the three planets would be in the exact center of the backlash space
of the sun and ring meshes. In this position the response of each planet gear would be identical, and contact would
occur at the exact same instant. The symmetrical position is deliberately avoided. The sun, planets, and ring begin
within the backlash space, but slightly displaced from the perfect center. In this way contact occurs on each element
at different times, and the interesting force response of Fig.4 are observed. This near equilibrium position creates the
difference in contact force magnitudes, which is driving the behavior of the planetary transmission. The near
equilibrium position is utilized in all simulations presented in this investigation.
4. Dynamic response and discussion of a planetary gear with free ring gear
This discussion is an extension of the free vibration explored in section 3. Both the ring gear and gear 1 are
now unconstrained and allowed to rotate freely. The initial velocity of the carrier is now transferred into all of the
transmission elements, instead of only the sun and planets. Due to the ring gear's relatively large mass moment of
inertia, the introduction of its rotation causes some interesting phenomena.
The results of this more complicated free vibration are counter-intuitive. The elements no longer oscillate
with the same frequency with respect to the equilibrium position. The system returns to this position at 93 ms,
instead of the quicker period of 20ms shown in Fig.3. The sun, planets, and carrier have the same period of 27 ms
because their rotations are coupled together. Similarly, a rotation of gear1 must cause a rotation of the ring gear, and
they are coupled together with the longer period of 93ms. Fig.5 depicts the relatively large system period of 93 ms.
Significantly more vibration occurs when an element reverses direction, shown in Fig.6. This is because of
the "time lag" caused by the various interplay of inertias. In section 3 when the sun makes contact with a planet, the
planet in turn makes contact with the ring which is a fixed rigid body. In this configuration when the sun makes
contact with a planet, the planet in turn makes contact with the ring, which in turn makes contact with gear 1, which
is freely rotating. Because no fixed element is present, only the gear inertias are contributing to the change in
angular velocity. Between 25 and 35 ms the sun makes contact with various planets, and its inertia makes a more
significant change in the planet's rotation than if the ring was fixed. The end result is this larger "settling time" as the
sun reaches its new angular velocity at 35 ms.
The magnitude of the contact force between dynamic elements is shown in Fig.7. A comparison with the
analogous plot shown in Fig.4 yields some important conclusions. The repeating symmetry of section 3 is not
observed. The first significant impact, occurs faster than it does in the fixed ring configuration. The interval in which
the impact takes place has decreased. For example, the sun and planet 2 are in contact for 20 ms in section 3, but
now only remain in contact for 15 ms. This can be explained by again considering that the inertias of all components
are now interacting. When the sun makes contact with planet 2 the rotation of the ring and gear1 are ultimately
effected, and therefore the time in which these two elements are in contact is less than if the ring and gear1 were
fixed. The general shape of the curve is the same, only the impact duration has changed.
5. Dynamic response and discussion of a planetary gear with constant velocity from sun gear
The ring gear is fixed and the sun gear is being driven by Motor 1, which is assumed to have a constant
angular speed of 975 rpm = 102.1 rad/sec. Fig.8 is the magnitude of each gear's angular velocity. Obviously, the
![Page 4: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/4.jpg)
planet gears must be rotating in a direction opposite that of the sun and carrier. For the first few milliseconds it is
observed that the angular velocities change rapidly, and converge to an average speed based on the gear ratios. The
planets have a much smaller rotary inertia relative to the carrier assembly. Since the planets experience forces from
the sun and internal ring, it follows that their angular velocities should change with a larger magnitude. These
"oscillations" die out rather quickly because the system is being driven by a kinematic motion constraint. In other
words, the sun will have a constant velocity regardless of any force it experiences. This loading assumption
essentially "forces" the other elements to reach steady-state very quickly.
The sun and planet 1 share an interesting force history shown in Fig.9. The large peaks can be attributed to
the configuration in which the sun is in contact with only one planet. The smaller peaks include "load sharing"
between the other two planet gears. The force between the sun this planet is reduced when the sun is in contact with
the other planet gears. The peaks and troughs of this plot are due to the rapidly changing contact ratio on the sun.
Consideration of a sun gear with a "chipped" tooth is depicted in Fig.10. This planet gear is in mesh with
the chipped area of the sun. In the first millisecond, fewer impacts have occurred because of the damaged tooth. It
takes longer for the gears to make contact because geometry is simply missing. The magnitude of the velocity
change has also increased, particularly between 1 and 3 ms. This is because the planet gear has more room to move
in the backlash due to the gap created by the missing tooth. An impact causes a change in acceleration, which is
allowed to propagate further because of the gap. The response of the gears become nearly identical after 10 ms
because the chipped tooth has moved through the mesh.
6. Dynamic response and discussion of a planetary gear with a step torque applied to the sun gear
With the ring gear fixed, a step input torque with the magnitude of 70.518 N-m is applied on the sun gear over 100
ms. A step torque of the form T(1- t/τ) is applied to represent a typical electric motor characteristic curve. The
torque magnitude and time constant is calculated using the rated torque and rated speed.
Compare the contact force magnitude of Fig.1 1 with the analogous plot of Fig.9. The first significantly
large magnitude response occurs at 9 ms for the constant input speed section 5, while the same magnitude here
begins at 25 ms. This delay is due the dynamic nature of torque. A torque applied to a body will not instantaneously
cause motion, instead it causes an angular acceleration. This acceleration works against the inertia of the sun,
causing the response to occur later than the constant speed case. The smaller peaks and troughs are again due to the
rapidly changing contact ratio on the sun. The largest peaks occur when this planet is the only planet gear in contact
with the sun.
The chipped sun experiences fewer impact events than the standard sun, shown in Fig. 12. This is because
an entire tooth is missing and it takes longer for the gears to contact. The magnitude of the velocity changes for the
chipped sun are larger. This is because the torque has had more time to accelerate the sun before contact is made.
This larger velocity change corresponds to a larger force magnitude. The chipped tooth causes the sun to experience
more harsh start-up conditions. These oscillations die out quickly as the torque continues to accelerate the system,
and the contact between gear teeth becomes constant on one side only. Velocity changes from positive to negative,
like those shown here, represent double sided impacts.
7. Dynamic response and discussion of a planetary gear with a step torque applied to both sun gear and gear
1
The system is operating as a differential transmission, with both Motor 1 and Motor 2 in operating in the
same direction. A step torque of the form T(1-et/τ) is applied to represent a typical electric motor characteristic
curve. The torque magnitude and time constant is calculated using the rated torque and rated speed, which are
70.518 N-m and 67.935 N-m on the sun and gear 1, respectively.
With the ring gear fixed as in Fig.13(a), the sun gear closely follows the input torque curve. The planets
dissipate energy from the sun input to the carrier output. The planets must get the carrier inertia moving from rest.
The sun, having the smallest inertia, oscillates with the largest amplitude of any gear. The amplitude of the sun
![Page 5: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/5.jpg)
gear's velocity change is decreased with the system operating as a differential transmission, shown in Fig.13(b). The
rotation of the ring causes the planets to move in the same direction as the applied torque on the sun. This makes the
angular velocity of the sun more smooth when compared to the simple planetary configuration of the fixed ring. This
effect is also seen in the other gears. The detrimental effects of the chipped tooth on the sun gear is lessened with the
system operating in the differential mode.
The gear 1 and ring mesh has a smaller prescribed backlash that the meshes between the sun and planets.
Therefore, contact occurs between these two gears before the sun and planets. A clear succession of contacts is
observed. First gear1 contacts the ring, the ring contacts a planet, and the planet contacts the sun. The interval from
3.5 ms to 4.5 ms in Fig.14 clearly shows this progression. The planet gears are potentially in contact with both the
sun and ring. The contact between gear 1 and the ring directly affect the magnitude of the force between the planet
and ring, shown as the smaller peak at 7.5 ms. The response of planet gear is a superposition of impact forces
between its sun mesh and ring mesh.
8. Conclusions
A practical differential planetary gear train which combines two inputs and one output has been analyzed
using a non-linear multi-body dynamics software model. To avoid interference and undercut the backlash between
the sun/planet and planet/ring meshes are precisely specified. When the transmission operates with a fixed ring gear
and undergoes free vibration from a near equilibrium position, six contact forces are potentially active. The
magnitude of the contact force between each element is shown to depend on the rapidly changing contact ratios of
each gear. For free vibration and a freely rotating ring, the duration of the contact event between gears decreases.
When compared to the perfect mesh geometry, a planet in mesh with the chipped tooth of the sun causes its angular
velocity to change with a larger magnitude. Step torques of the form T(1 –e t/τ) applied in opposite directions to each
input closely models the constraints and loading conditions of realistic operation. The transient response of this
differential mode is shown to be significantly less destructive to the sun gear. The interactions of many components
of this differential planetary transmission contribute to the complicated transient behavior observed in the time
domain.
9. Acknowledgement
The authors acknowledge the Donald E. Bently Center for Engineering Innovation at California Polytechnic State
University San Luis Obispo for support of this work.
![Page 6: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/6.jpg)
REFERENCES
1. Özgüven H.N. and Houser D.R., ―Mathematical Models used in Gear Dynamics – A Review‖, Journal of
Sound and Vibration, 121(3), 1988, pp. 383-411.
2. Parey, A. and Tandon, N., ―Spur Gear Dynamic Models Including Defects: A Review‖, The Shock and
Vibration Digest, Vol. 35, No. 6, Nov. 2003; pp. 465-478.
3. Parey, M. El Badaoui, F. Guillet, N. Tandon, ―Dynamic modeling of spur gear pair and application of
empirical mode decomposition-based statistical analysis for early detection of localized tooth defect‖,
Journal of Sound and Vibration Vol. 294, 2006, pp. 547–561.
4. J. Lin and R. G. Parker, ―Parametric Instability of Planetary Gears under Mesh Stiffness Variation”,
Journal of Sound and Vibration, 2002, vol. 249, pp. 129-145.
5. J. Lin and R. G. Parker, ―Analytical Characterization of the Unique Properties of Planetary Gear Free
Vibration”, ASME Journal of Vibration and Acoustics, vol. 121, July 1999, pp. 316-321.
6. Yi Guo and R. G. Parker, ―Dynamic Modeling and Analysis of a Spur Planetary Gear Involving Tooth
Wedging and Bearing Clearance Nonlinearity”, European Journal of Mechanics A/Solids, 2010, vol. 29,
pp. 1022-1033.
7. R. G. Parker and X. Wu, ―Vibration Modes of Planetary Gears with Unequally Spaced Planets and an
Elastic Ring Gear”, Journal of Sound and Vibration, 2010, vol. 329, pp. 2265-2275.
8. Yichao Guo and R. G. Parker, ―Purely Rotational Model and Vibration Modes of Compound Planetary
Gears‖, Mechanism and Machine Theory, 2010, vol. 45, pp. 365–377.
9. Kong, D., Meagher, J., Xu, C., Wu, X., Wu, Y., ―Nonlinear Contact Analysis of Gear Teeth for
Malfunction Diagnostics‖, IMAC XXVI a Conference on Structural Dynamics, Society for Experimental
Mechanics, Orlando, Florida USA, February 4 –7, 2008.
10. MSC Inc., MSC ADAMS reference manual.
11. Raymond J. Drago, ―Fundamentals of Gear Design‖, 1988.
12. Huamin Li, Guixian Li, ―Gear Mechanism Design and Application‖, 2007 (in Chinese).
13. Zengang Rao, ―Planetary Gear Transmission Design‖, 2003 (in Chinese).
![Page 7: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/7.jpg)
b
2x
B-D-ial~
B-D
(a) Schematic (b) CAD Isometric View
Fig.1 A differential planetary gear with two inputs and one output
Fig.2 Chipped tooth profile
![Page 8: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/8.jpg)
Table 1. Planetary gear design and simulation parameters
Module m (rom) m=2 Backlashes (rom) B I = 0.04; B2= 0.03
Z.=20; Zt, = 94;E = 2.07 X lOll Pa;
Number of teeth Material properties V= 0.29;Zc= 37; ZI =28; Z2 =98
P = 7801 kg/m3
Standard Pitch circle da= 40; db = 188;Force exponent 2.2
diameter d(rom) dc=74; d l =56; d2= 196
Gear Ratios 5.7; 1.213 Penetration 10-7 (rom)
Pressure angle 20· Stiffness 2x 107 (N/rom)
Table 2. Dynamic Conditions Depicted in Figures
Fig. No. Simulation Parameters3,4,5 (OxO = 100 rad/sec initial angular velocity applied to the carrier, fixed ring
6,7 (OxO = 100 rad/sec initial angular velocity applied to the carrier, free ring8,9,10 (01 = 102.1 rad/sec constant angular velocity applied to the sun, fixed ring
11, 12, 13(a) T I = 70.518 N-m step torque applied to the sun, fixed ring13(b), 14 T I = 70.518 N-m step torque applied to the sun, T2= 67.935 N-m applied to gear 1
M- I'll"
t.i.II ... .. rII \ rv
1.~or·
_..~, "'""-.....~it, I~I\~" 1'-1 I....... .p .r f>- ..... /-ll
JI~I ...... --'.--
"'~
ll~lb~~~'1I"t ...'I.{.,~ , '""1.... 1 _'".1J_II "..'" 1'-.../ I\. ! r 1......~ ~ftt' rl"/ll rv.,"",~ ir=-
\ I..II
""1'-\ 11""'-
""l. ... .:iW sun- -planets-carrier
0.4
03.2
0.24
0.16
0.08In
E0.0:a
2:-0.08
-0.16
-0.24
-0.32
-0.4o 3 6 9 12 15 18
ms21 24 2:7 30 33 36
Fig.3 Angular velocity vs. time, when initial angular velocity 0),,0 = 100 rad/sec is applied to the carrier
![Page 9: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/9.jpg)
35301812
/ \
( 1II I
-f---+-----l---+---+--+---f-----+---+--I f--- ",-+--+---1
I \
-J---+-----l---+---+---+---f__---+---+---HII..l'.. " ~M
-f---t---+----1-t''-'I.-t----+---+---+---+--'H---jII-+-----t---l
,/\If V...... / \
....---+-----lIH-J1'---+---+--\\-I-J-t---+---+---+--N,fr_f__--tI'.I---+---lV ~ )',__---+---Jil---'---+---+---'--~L+---f__---+---+-__,_I,--+---+II-----lf---_lr '\ ' I t~ 'rI\__---+--H-H-----+o~j-\ -,11\---+---+---+-'-1---+---+11-1-1---+---'
/ \ J I I
tj-f----rG \., / ~I I \J ~ I' 1-M: .., ~ "'\-r. I,\fl --sun, planet 2AU ii, - - -sun, planet 3
-I ~ - J,~. 1"Il.6Il.ll..~ 1I" -planet 1, ring
24
250000
225000
200000
175000
150000
c0
1i 125000QJz
100000
75000
50000
25000
00
ms
Fig.4 Contact forces vs. time, when initial angular velocity OlIO = 100 rad/sec is applied to the carrier
![Page 10: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/10.jpg)
1\r ...............
~-P\I / -- /\II \ j / '- I
\ / J \ "" I \I ~,. f \ " I \
j r- / / -' i-..,... \
~~~\
1/ v r--... \ / '\1............\~~~ ....___L---IJ" ~'~ I I \ '~ .........
1//1 -.- 1\\ / '\ \ ............ -- // .......1- ~ \\
~ 1/ I\...\ 1/ ~~~\. J/ '\ \~ r1 \~~l \ '\\f7! /
\ I sun
V \-planets --carrier --ring-gear1 -
2.5
2.0
1.5
1.0
0.5..,~
0.0
-0.5
-1.0
-1.5
-2.0o 10 20 30 40 50
ms60 70 80 90 100
Fig.5 Angular displacement vs. time, when initial angular velocity OlIO = 100 radfsec is applied to the carrier
Ilrm....~ ·A j I~~~ I 1_
f\ A V T ....
M.\ \
f--
/ ~1 U ~~
~ - ~'.J~ IV .~nJ
... r.IrJU j1..I" r...I II"" - ~ "'r ttl-M_ 1.Joit ~_1or\ II-- - """'" nn11
. j V V \r ~~~r ..R.~IT\ - - -
-'~
~\ff
-\
....h....,. ".n~ ,..{\. ~sun
"II - -planets-gear1
0.3
0.2
0.1
'"E0.0:a
~
-0.1
-0.2
-0.3o 5 10 15 20 25
ms30 35 40 45 50
Fig.6 Angular velocity vs. time, when initial angular velocity OlIO = 100 rad.fsec is applied to the carrier
![Page 11: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/11.jpg)
-f---+_-+----1_-+-_+----+-_+II-I!\_--+_-+-+r.\,+----1_-+-_+----+-_+--_1
1\til '\
I Ij i! \If ~
'L,~
I \-U--+--+----f-----t---+li-I--+r---+---+---+---+----I-f--I'-I+--+---+--+--I
J
4 8 10 12 14 16ms
Fig.7 Contact forces vs. time, when initial angular velocity OlIO = 100 rad/sec is applied to the carrier
f--(")
III) II
-II 1rill
~ 1,_:1~I-H· 1-1-~ ~ ~11-1-1 ,-,-
1I ~ '-i{- 1\ ) II f _p,- -\-1-"-IftTI Tlf ~- i \ II \t\~ i;J"\!v " - ~~il!.."\.,,~ /'~ ~ - \- r v- ,...-
Y:"-ltL\-\ -f'- I
"'~~AJ- ~I!o,..... I... \
~ ~~~1\1 L1:rn v J\ sun\ I
IV Y
- -planets-(-
~J -carrier
0.11
0.10
0.09
O.OB
0.07
E 0.06U2::! 0.05
0.04
0.03
0.02
0.01
0.00o 2 3 4 5
ms6 7 B 9 10
Fig.8 Angular velocities vs. time, when constant angular velocity Olt = 102.1 rad/sec is applied to the sun
![Page 12: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/12.jpg)
I
I \f\ "\
{~r]J \\ ~ A
~/ V\)1 \
J \.JJ~ ~~AJ IV~I '"'~ --sun, planet I
40000
30000
co~ 20000<llZ
10000
oo 5 10 15 20 25
ms
Fig.9 Sun-planet contact force vs. time, when constant angular velocity rot = 102.1 rad/sec is applied to the sun gear
0.07 -,--.----,------,-----,-----,----,----,---,---,-----,-----,-----,----,---,---,---,----;.------.----,----,
0.063 -/--+-I--I-+-----I---+--+--+--+--+--+----I---+--+--+--+--+--+-----1f----+--+--1
0.056
5.04.54.03.53.02.5ms
2.01.51.00.5
.-
0.042
- -1-1-1--I-1-'~,+---+--+-.....+---1--+--+--+---+---+--+---1--+--+--+---+---+--1t~ r-~ (I-F'\I---+,I'-:+--i,-~--+---+----11----+--+--+---+---+---+---1--+--+--+---1-HI-i,f="'i'J-++t-lI-I---+,,--,+--+'1n----,+--+---t---1I--t--+--+--+--+---t---1I--t--+---1
__ )--1-1-1--I-+-i)-I : 1 1 -{--.f11Iio-__+----1I----+_-+--+_-_+_-_+-__+-__1--+_-+--+_--1- .I ' 7'"""-ll+'+-H-iIt.--!- nIT~-,..-+-+"~r-f---j..,.~+--+....,..-+-I.-+--+--+--+--+--+---I! ' II:' I I } ~, ,\ rf\ N. n ...
;-1-+1:--I--H)-I--+,--IIi,--III:,"~I':·'-ll~ ~,-I' \,_,-;--\ -,1-\ 1 \ J \ rfi J~\~liIJ~h '\-r In
O. 028 -Hi:rl-tlI!I-I'!+--'II--1~I--I~t-_-,r ---J: r\ ..J..-f-'Ir i--H-t+,'---------J~\:\,,--fi-_-\\-+I-'l\.l:i-ttll-:/,j--\ J?~'tV -\I~'~-¥l~
0.021 +1t1-t-tl"H'L
11•1_--I-_=:+!_---+f,.iJ_H-'_-11
11_-1-+(r--i
l,'_--tl----\,,~:-''-_-_--,"tJ,L~',}__- _-+t-_-"_\"~cf-t+_-_-_-'-1~~'----=-=t-~-!-+---1--t--+--+--1, \ -' ''':'"'''') '_ .1 \.l
I I I I :' I I \j-j-f--li-I--tt--If-I,I---'rr-,-!r'--+L!-+i--1+-~I..-t----"+--+--+--+--+---1--t--+--+--+--+--1-\-I+I--t\--t',i-I--!l-,-,,'-+, l~t~t=::t=j=j=jt=t=t=t==~~~;=:::±=:::jt::::~1-,--III·-I,.1IoJ1'--+'-'=I·', I----f- t, -planet
0.0 ~'L-----.l_..L.!i.,~~_.....!.._---l-_-.-L"_---l-_...L_--1-_--.L_-l-_L_+-_L_J-_!'==-=-=i-F·p=l=an=e=t""(c=h=fiP~P=e=d=s=u=n~)
0.0
0.014
0.007
0.049 1--
'"~ 0.035[':'
Fig.l0 Angular velocities vs. time, when constant angular velocity rot = 102.1 rad/sec is applied to the sun
![Page 13: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/13.jpg)
40000
35000
30000
25000
co
~ 20000z
15000
10000
5000
j\
\ I1 1\ )
\ /-
~ ·A-' \
~1.11
i-~-,
I \~,~ j
I I'I ~~ JJJ'
Ilill ~ r --sun, planetIi. .J"'I
o 5 10 15 20 25ms
30 35 40 45 50
Fig.H. Sun-planet contact force vs. time, when the torque T1 = 70.518 N-m is applied to the sun gear
![Page 14: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/14.jpg)
0.05I
0.04J'IJI I
- -~-0.03
I
5.04.54.03.53.02.5ms
2.01.51.00.5
,, ,I
-,-1--+---+---+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--1-1-1---+---+---+---+---+--+--+--+--+--+--+--+--+-+-1-'---'---'--,1, I sun
-1--+I-f-+--+--+--t--t--t--t--t--f----If---t--f----If----I---t-11-- -~chippe d sun
-IIH-Il-li--ftI--I......'1 !: I 'I I~\ II; \ / -l-~'v..\-' \ j):-,.,LI-1-tlt."I,_+_V_"rl,_I---1f----t------,"',+'_-+_-+_-1
i ; U-~: r--\-l--\ ~\i_'-+1t1-_J-+__\W__+-\_}'-+V_-+_-+_-+_-+_-+_-+_-+_-I-:- ~: - - : \='I--+--+--+--t---t---+--t---+--+--I-----1I-----1I-----1I---1_1- rl- .-1+-1-1-+--+--+--+--+--+--+--+--+--+--+--+--+---+---+---+--1
-1--l-H-Ii--l
-111,-ilf--+-¥_t--t--t--t--f---f----If----I---If----If----I---t---t--+--+--+--I, ,, I I
III
-/--f-~'_-iL--I+-11--\-I~!-__.-t~--I\_-t!I~·-\--tI\--+-f\-+--+--+--+--+--+--+--+--+--+--t---t---II I ~ 1 I Lt I ~ {, """' 1If-~ f '\ _ ,f" _: I : i' ·\-W\----:j, \ '\ \ /tl' r 1\ \"".,d~, 1T'l("....;;"........i~~
OOQ:
0.01 -
<J>
E0.0CO
~
-001-
-002 -
~0.03
-
-004 -
-0.050.0
Fig.12 Sun angular velocity vs. time, when the torque T1 = 70.518 N-m is applied to the sun gear
v. - V
~~
"l. I
!If ~ - ...J......l... 1- 1 I I
-chipped sun- -planets-carrier---ring-gear1
0.05
0.04
0.03
OOQ:""
0.01I'rV
<J> ""i\j
S "fll0.0
,-.::l " f- I" +. I I 1.-r:l r -
-0.01
-002
-0.03-sun
~0.04 - -planets-carrier
-0050 2 3 4 5 6 7 8 9 1(
ms
0.05
0.04
0.03
0.02
0.01
00
-0.01
-0.02
-0.03
-0.04
-0.05o 1 234] 5 678
ms
9 10
(a) Ring gear fIXed, T1 = 70.518 N-m (b) T1 = 70.518 N-m, T2 = 67.935 N-mFig.13 Angular velocity with applied step torques
![Page 15: A Differential Planetary Gear Model with Backlash and](https://reader030.vdocuments.us/reader030/viewer/2022012505/617f8382c90edf125e58ec25/html5/thumbnails/15.jpg)
---
A-
~I
(
II -III n! \
~I I ~\- \~I
n I I
- --gear 1, ring 1. f-,
~A!-- - -ring, planet I (
~\ V "'V
I \( {
-planet, chipped sun ( j1 J ~ I f \ , IJ ~ ....
125
100
75
co1iQ}
z
50
25
oo 2 3 4 5 7 8 9 10
ms
Fig.14 Angular velocity when torque T1 = 70.518 N-m is applied to the sun gear and T2 = 67.935 N-m is applied to gear