www.tjprc.org [email protected]
CHROMATOGRAPHY A COMPETENT TOOL FOR PHYTOCHEMICAL P ROFILING
OF MEDICINAL PLANTS – A REVIEW
SONIA, N. S.1 & JESSYKUTTY, P. C.2 1Department of Plantation Crops and Spices, College of Agriculture, Vellayani,
Kerala Agricultural University, Thrissur, Kerala, India 2Associate Professor, Department of Plantation Crops and Spices, College of Agriculture Vellayani
Kerala Agricultural University, Thrissur, Kerala, India
ABSTRACT
Chromatography is a physical method of separation of components in a mixture by distributing it between a
stationary phase using a mobile phase. Based on geometry of technique there are planar chromatography and column
chromatography. In planar chromatography the stationary phase is present as a plane or on a plane and in column
chromatography it is embedded with in a tube. Planar chromatography includes paper chromatography, Thin Layer
Chromatography (TLC) and High Performance Thin Layer Chromatography (HPTLC). Column chromatography
includes Liquid Chromatography (LC), Gas Chromatography (GC) and Supercritical Fluid Chromatography (SFC). High
Performance Liquid Chromatography (HPLC) is a faster separation system with different modes of elution, mode of
functioning as well as separation techniques suited for heat sensitive compounds whereas GC can separate components
present in volatile oils only. SFC uses a supercritical fluid usually carbon dioxide for the separation of components which
are difficult to be handled by both LC and GC. Chromatographic systems are hyphenated with sophisticated detectors like
mass spectrometers (MS) or tandem mass spectrometers (MS – MS) for precise identification as well as quantification of
molecules.
KEYWORDS: Stationary, Mobile, Planar, Column, Mass Spectrometry
Received: Mar 02, 2016; Accepted: Mar 14, 2016; Published: Mar 21, 2016; Paper Id.: IJMPSAPR201609
INTRODUCTION
World Health Organisation (2008) has defined medicinal plants as plants that contain properties or
compounds that can be used for therapeutic purposes or those that synthesise metabolites to produce useful drugs.
It’s the aim of a drug researcher is to discover a new, safe and active chemical entity from the crude drug which has
therapeutic value for any disease or disorder.
For developing a drug, the crude drugs have to be dried, extracted and isolate the active components using
different analytical techniques. The isolates have to be further purified and standardized using pharmacological,
metabolic and pharmacokinetic studies. Once the compound was standardised/optimized for its therapeutic potential
the drug or dosage forms can be developed (Patil et al., 2013).
In all these stages the authenticity of both the crude drugs and product have to be ensured. When we get a
crude drug or a drug formulation, we have to assure the identity of its active ingredient as well as the impurity
profile of the drug for establishing its therapeutic safety. Since, misidentification of plants, contamination,
Original A
rticle
International Journal of Medicine and Pharmaceutical Sciences (IJMPS) ISSN(P): 2250-0049; ISSN(E): 2321-0095 Vol. 6, Issue 2, Apr 2016, 73-86 © TJPRC Pvt. Ltd.
74 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
substitution and adulteration of plants, failure of good manufacturing practice and incorrect preparations and/or dosages are
problems in drug industry (Calixo, 2000). Even after drug development, its quality (purity, strength, presence of any
degradation products etc.) has to be assured (Gillard and Ritter, 1997). Also, the quality of a drug or a drug formulation
varies with time under the influence of temperature, humidity, light etc. So, to establish a shelf life for the drug product by
recommending ideal storage conditions a stability testing is essential (Huynh-Ba, 2009).
For all these studies, high sensitivity and selectivity is required since, the concept of quality is a paramount factor
which must get good attention. WHO has emphasized the need of ensuring quality of medicinal plant products by using
modern techniques like ultraviolet/visible spectrophotometry, fluorimetry, titrimetry, electroanalytical techniques,
chromatographic methods, capillary electrophoresis and vibrational spectroscopies etc. by applying suitable parameters and
standards (Mehta et al., 2011). Of these, chromatography is a multi-disciplinary tool with higher degree of precision and
accuracy (Srivastava, 2011).
CHROMATOGRAPHY
Chromatography is a physical method of separation in which the components to be separated are distributed
between two phases, one of which is stationary (stationary phase) while the other (mobile phase) moves in a definite
direction (IUPAC, 2006). The word ‘chromatography’ is derived form two Greek words Chroma (colour) + Graphein
(writing) together means ‘colour writing’. Mikhail Semenovich Tswett invented chromatography in 1903 during his
research on plant pigments. He used the technique to separate various plant pigments such as chlorophylls, xanthophylls
and carotenoids in a plant extract. He had taken a glass column and filled with powdered limestone (CaCO3) (LC-GC
Europe, 2003).
In chromatography, the sample is dissolved in a mobile phase (may be liquid, gas or supercritical fluid) and is
allowed to run over the stationary phase (fixed to a solid surface). These two phases are selected in such a way that the
components of sample distribute themselves between mobile and stationary phases to varying degrees. Those components
strongly retained by the stationary phase move slowly with the flow of mobile phase and those which are weakly held will
travel rapidly through the column and gets eluted first. This difference in migration rates, make the sample components to
be separated into distinct (discrete) zones which can be used for quantitative or qualitative analysis (Miller, 2005).
Chromatographic fingerprint of a herb is a chromatographic pattern of the extract of some common chemical
components of pharmacologically active and/ or chemical characteristics (Patil and Shettigar, 2010). In the finger print we
have to look for its integrity and fuzziness or sameness and differences to chemically represent that herbal medicine.
Chromatography restricts not to analytical separations, it is used in separation of pure substances (purification), study about
kinetics of reactions, structural investigations on molecular scale also, in determination of physiochemical constants like
enthalpy, entropy, free energy etc.
TYPES OF CHROMATOGRAPHY
Among these techniques, for phytochemical profiling, choose a suitable one depending on the chemical
composition, chemical nature, physical and chemical properties and physical state of that test substance. Since, different
types of functional groups, acidic, basic or neutral substances, substances with different polarity, molecular mass,
refractive index, density, viscosity, also the different states of matter like solid liquid or gas. As shown here (Table 1.)
chromatography is classified based on various parameters (Chavan et al., 2013) of which geometry of the technique is
Chromatography a Competent Tool for Phytochemical Profiling of Medicinal Plants – A Review 75
www.tjprc.org [email protected]
found ideal to discuss all other types.
Table 1: Classification of Chromatography
Parameters Principle of Separation
Mobile Phase Used
Geometry of Technique
Scale of Operation
Mode of Technique
Elution Method
Types Partition GC Planar – Paper, TLC, HPTLC
Preparative Normal phase
Gradient Adsorption LC
Size exclusion SCF chromatography
Column – GC, HPLC, SFC, UPLC
Analytical Reverse phase
Isocratic Affinity Ion exchange
Based on the geometry of chromatographic technique there are planar and column chromatography. In planar
chromatography the stationary phase is present as a plane or on a plane and in column chromatography it is embedded with
in a tube (IUPAC, 2006).
Planar Chromatography
Planar chromatography includes Paper Chromatography, Thin Layer Chromatography (TLC) and High
Performance Thin Layer Chromatography (HPTL
Paper Chromatography
Paper chromatography works by the partition of solutes between water in the paper fibers (stationary phase) and the
solvent (mobile phase) (The Royal Society of Chemistry, 1997). This technique can be used in herbal studies for
prliminary screening or to know the presence of any particular compound. Devare et al. (2011) used this technique for
preliminary phytochemical screening of aminoacids in acetone, chloroform, ethanol and water extracts of Morinda
pubescence and reported that the leaves of Morinda is a rich source of different aminoacids also, water is a good solvent
for extracting it.
Paper chromatography can provide only a rough estimate of the compounds, separation takes place very slowly (10 to
20 hours) and also, the spots tended to be much more diffused. This technique is now obsolete, except perhaps as an
inexpensive technique for teaching chromatography in schools and colleges. But, its introduction must truly regarded as a
revolution since, it led ultimately to the award of Nobel Prize to Martin & Synge in 1952 (Wilson, 2000).
Thin Layer Chromatography (TLC)
TLC is a widely employed laboratory technique and is a modern version of paper chromatography. However,
instead of using a stationary phase of paper, it uses a thin layer of adsorbent like silica gel, alumina, or cellulose on a flat,
inert substrate like glass, thick aluminum foil or plastic (Kumar et al., 2013).
The principle of TLC is the distribution of a compound between a solid fixed phase applied to a glass or plastic
plate and a liquid mobile phase, which is moving over the solid phase. A small amount of a compound or mixture is
applied to a starting point just above the bottom of TLC plate. The plate is then developed in the developing chamber that
has a shallow pool of solvent just below the level at which the sample was applied. As the solvent slowly travels up the
plate, the different components of the dye mixture travel at different rates and the mixture is separated into different
coloured spots. The mobile phase will carry the most soluble compounds the farthest up the TLC plate and less soluble
ones will stay behind (Singhal et al., 2009).
76
Impact Factor (JCC): 5.4638
The behavior of an individual compound in TLC is charact
and is expressed as a decimal fraction. The Rƒ is calculated by dividing the distance the compound travel
original position by the distance the solvent travelled from the original position (th
2007).
Figure 1:
Coloured substances can be seen directly
making them visible using spraying agents like iodine vapours, potassium permanganate, potassium dichromate etc. which
produces coloured areas in the region which they occupy. Also, some fluorescing materials can be added to the adsorbent
during preparation of TLC plate and these
Rƒ values can be used to aid in the identification of a subst
physical constant and comparison should be made only between spots on the same she
substances that have the same Rƒ value may be identical; those with different R
TLC is used for different purposes like identifying the presence of a particular compound in a crude drug as
reported by Kumar and Dhillon (2015) in
red data book for confirming the presence of
and tenoposide. TLC of methanolic extracts of its leaves and roots reported an
TLC helps in authentication of herbal drug for
Bilwadi churna, Gangadhar churna, and Pushyanug churna
(Bilva patra) by Singh and Kumar (2015). In the TLC plates, Bilva patra
Bilwadi churna showed three spots (0.89, 0.80 and 0.63) and Pushyanug churna showed two spots (0.89 and 0.66)
matching with two phytoconstituents of Bilva Patra whereas Gangadhar churna showed two spots of w
matching with Bilva Patra (0.63). These difference may be due to the difference in geographical distribution,
manufacturing process, stage of harvest etc. or it may be due to the intentional or unintentional adulteration.
Revathy et al. (2011) have tested various solvents systems in TLC for extraction of curcuminoids like curcumin
(C), demethoxycurcumin (DMC) and bisdemethoxycurcumin (BDMC) from the acetonic extract of
solvents systems were tried and among them d
C, DMC and BDMC were obtained for chloroform: methanol
compounds in HPLC.
Presence of antimicrobial compounds in
the technique is named as bioautography. Here, the test microbial cultures have to be poured over the resolved TLC plates
of particular medicinal plant. These plates on incubation for
presence of antimicrobial compounds which can be identified using the corresponding R
The behavior of an individual compound in TLC is characterized by a quantity known as Rƒ (Retention factor)
and is expressed as a decimal fraction. The Rƒ is calculated by dividing the distance the compound travel
original position by the distance the solvent travelled from the original position (the solvent front)
Figure 1: Determination of Retention Factor (Rf)
red substances can be seen directly in stationary phase, while colourless substances can be detected by
spraying agents like iodine vapours, potassium permanganate, potassium dichromate etc. which
red areas in the region which they occupy. Also, some fluorescing materials can be added to the adsorbent
during preparation of TLC plate and these can be viewed under the UV light (Archana et al., 2011).
values can be used to aid in the identification of a substance by comparison to standards.
and comparison should be made only between spots on the same sheet, run at the same time. Two
value may be identical; those with different Rƒ values are not identical.
TLC is used for different purposes like identifying the presence of a particular compound in a crude drug as
Dhillon (2015) in Podophyllum hexandrum, an endangered species of medicinal plant listed under
he presence of Podophyllotoxin, a compound for the synthesis of anticancer drugs etoposide
and tenoposide. TLC of methanolic extracts of its leaves and roots reported an Rƒ value of 0.87 and 0.94 respectively
TLC helps in authentication of herbal drug formulations also. TLC finger prints of three polyherbal formulations
Bilwadi churna, Gangadhar churna, and Pushyanug churna were prepared for finding the presence of
(Bilva patra) by Singh and Kumar (2015). In the TLC plates, Bilva patra showed four spots at 0.89, 0.75, 0.65, and 0.52,
Bilwadi churna showed three spots (0.89, 0.80 and 0.63) and Pushyanug churna showed two spots (0.89 and 0.66)
matching with two phytoconstituents of Bilva Patra whereas Gangadhar churna showed two spots of w
. These difference may be due to the difference in geographical distribution,
manufacturing process, stage of harvest etc. or it may be due to the intentional or unintentional adulteration.
. (2011) have tested various solvents systems in TLC for extraction of curcuminoids like curcumin
(C), demethoxycurcumin (DMC) and bisdemethoxycurcumin (BDMC) from the acetonic extract of
solvents systems were tried and among them desired resolution of separation and Rf values matching with the standards of
tained for chloroform: methanol. So, it is selected as a suitable solvent for the separation of
Presence of antimicrobial compounds in medicinal plant samples can also be identified with the help of TLC and
the technique is named as bioautography. Here, the test microbial cultures have to be poured over the resolved TLC plates
of particular medicinal plant. These plates on incubation for a few days could yield some inhibition zones representing the
presence of antimicrobial compounds which can be identified using the corresponding Rf values.
Sonia, N. S. & Jessykutty, P. C.
NAAS Rating: 3.54
erized by a quantity known as Rƒ (Retention factor)
and is expressed as a decimal fraction. The Rƒ is calculated by dividing the distance the compound travelled from the
e solvent front) (Figure 1) (Skoog et al.,
rless substances can be detected by
spraying agents like iodine vapours, potassium permanganate, potassium dichromate etc. which
red areas in the region which they occupy. Also, some fluorescing materials can be added to the adsorbent
., 2011).
ance by comparison to standards. The Rƒ value is not a
et, run at the same time. Two
values are not identical.
TLC is used for different purposes like identifying the presence of a particular compound in a crude drug as
, an endangered species of medicinal plant listed under
Podophyllotoxin, a compound for the synthesis of anticancer drugs etoposide
ƒ value of 0.87 and 0.94 respectively
. TLC finger prints of three polyherbal formulations
were prepared for finding the presence of Aegle marmelos Corr
showed four spots at 0.89, 0.75, 0.65, and 0.52,
Bilwadi churna showed three spots (0.89, 0.80 and 0.63) and Pushyanug churna showed two spots (0.89 and 0.66)
matching with two phytoconstituents of Bilva Patra whereas Gangadhar churna showed two spots of which only one spot is
. These difference may be due to the difference in geographical distribution,
manufacturing process, stage of harvest etc. or it may be due to the intentional or unintentional adulteration.
. (2011) have tested various solvents systems in TLC for extraction of curcuminoids like curcumin
(C), demethoxycurcumin (DMC) and bisdemethoxycurcumin (BDMC) from the acetonic extract of Curcuma longa. Three
esired resolution of separation and Rf values matching with the standards of
. So, it is selected as a suitable solvent for the separation of
medicinal plant samples can also be identified with the help of TLC and
the technique is named as bioautography. Here, the test microbial cultures have to be poured over the resolved TLC plates
a few days could yield some inhibition zones representing the
values. Saenego and Ndip (2012)
Chromatography a Competent Tool for Phytochemical Profiling of Medicinal Plants – A Review 77
www.tjprc.org [email protected]
identified two compounds from Garcinia kola seeds, one with Rf of 0.53 which inhibits the growth of Streptococcus
pyogenes, Styphylococcus aureus and Salmonella typhimurium and another compound of Rf 0.63 which could inhibit
Salmonella typhimurium and Plesiomonads shigelloides.
TLC results are more reproducible, due to the use of much smaller silica particles as stationary phase that favours
a very efficient separation. The Rƒ is not a physical constant its value change with change in solvent system, adsorbent,
thickness of adsorbent and amount of the material spotted (Bilia et al., 2002).
High Performance Thin Layer Chromatography (HPTLC)
HPTLC is a sophisticated and automated form of thin – layer chromatography (TLC) with advanced separation
efficiency and detection limits. It is a powerful analytical technique equally suitable for qualitative and quantitative
analytical tasks (Sethi, 2013). Separation happens due to adsorption or partition or by both depending upon the nature of
adsorbents and the solvent system used. It is an instrument controlled by software (Kustrin and Hettiarachchi, 2014).
Here, sample is applied automatically and uniformily applied over the TLC plate specially designed for HPTLC
(silica particle size – 5 to 6 µm, layer thickness -100µm, sample volume – 0.1 to 0.5 µL, starting spot diameter – 1.0 to
1.5mm and seperated spot diamter – 2 to 5mm) using the sample applicator (Patel and Patel, 2008). The chromatogram is
developed inside a chamber filled with mobile phase and viewed inside a visualiser at different wavelenght of light and
finally documented. The software develops a peak corresponding to each compound and we can get the retention factor,
area of the height of the peak etc. from the result developed.
The use of modern apparatus such as video scanners, densitrometers and new chromatographic chambers and
more effective elution techniques, high resolution sorbents with selected particle size or chemically modified surface, the
possibility of combining with other instrumental methods and development of computer programs for method optimization
all make HPTLC an alternative to HPLC or GC. The major disadvantages include, bulky instrumentation, large space
requirement, expensive, requires dust free and stringent operation conditions and technically skilled persons to run the
system (Srivastava, 2011).
HPTLC can be used similar to TLC for the determination of bioactive component of herbal medicine, as a
chemotaxonomic tool in plant systematics and also for quality control and standardization of herbal drugs (Mahesh et al.,
2011).
Methanolic extract of leaves of Pala indigo tree/ Sweet indrajo (Wrightia tinctoria) [Family: Apocynaceae] popular
for its Psoriasis curing properties (Khyade and Vaikos, 2014) was analysed using HPTLC for the presence of compound
lupeol by Devi and Devakar (2012). Lupeol is an anti-inflammatory and anti-cancerous triterpenoid and it is reported to
contain 47.6mg of lupeol/ g of methanolic extract.
HPTLC analysis of Wrightia tinctoria (Pala indigo tree) and Wrightia tomentosa (Scarlet wrightia) by
Muruganandham et al. (2000) reported that indigotin, indigorubin, tryptanthrin, isatin, anthranallite and rutin were present
in Pala indigo tree whereas in Scarlet wrightia only anthranalite and rutin are present which can be a criteria for
distinguishing these species of medicinal plant. Another plant in Apocynaceae family is Holorrhena antidyssentrica
(Kudaka pala/ Kutja) containing an active principle conessine used for treating dysentery. Seeds and bark of this plant
resembles Wrightia tinctoria so, widely using as an adulterant in Wrightia tinctoria pharmaceutical preparations. Jirge
(2011) analysed two pharmaceutical formulations Kutja vati and Kutja capsules with Kutja bark using HPTLC and
78 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
reported a conessine content of 0.901 ± 0.71 % in Kutja bark and a lower value for both the formulations (Kutja vati –
0.725 ± 0.11 % and Kutja capsules - 0.692 ± 0.24 %)which may be due to adulteration.
Column Chromatography
Liquid Chromatography
A chromatography using a liquid as mobile phase is called liquid chromatography. The liquid used as the mobile
phase is called the “eluent” and here, stationary phase is usually a solid or a liquid. Sample solution is applied into a
porous stationary phase and mobile phase is delivered through the column at higher pressure so that separation occurs
based on the affinity of solute to the stationary phase. Need for higher degree of separation and faster analysis by refining
the packing material used as stationary phase to a size of 3 to 10 µm coupled with eluent delivery through a high pressure
pump facilitates the development of HPLC (High Performance Liquid Chromatography) (Charde et al., 2014). HPLC
instruments consist of a reservoir of mobile phase, a pump, an injector, a separation column and a detector (Gupta and
Shanker, 2008).
Solvent delivery pump delivers the mobile solvent and the injector introduces it into the mobile phase or onto the
chromatographic bed. Most important component of the HPLC system is the column where the sample components get
separated when it passes through this. The column is 10 to 30 cm long stainless steel tube having a diameter of 3 to 5mm
filled with silica gel. The separated components in the column will go to a detector for quantification and got recorded in
the computer system. The system will provide the phytochemical components as a fingerprint containing peaks.
HPLC is a highly flexible system since, its mobile phase, stationary phase as well as elution method is modified
into different chromatography types for meeting wide range of analysis requirements (IUPAC, 2006). Normal phase and
reverse phase are the two types of HPLC based on mode of separation where, the stationary phase is more polar than the
mobile phase in normal phase and vice versa in reverse phase. Lipophilic substances like oils, fats and lipids are separated
by normal phase chromatography. Since, most of the plant extracts are polar compounds reverse phase chromatography is
widely using for phytochemical finger printing of medicinal plants. Sivakumar et al. (2014) have standardised HPLC
procedure for quantification of berberine an isoquinoline alkaloid, from Tinospora cordifolia (Guduchi) using acetonitrile:
water (60:40) as the solvent system. They had compared berberine content of wild and micropropagated Guduchi and
reported that methanolic extract of both samples contain berberine (1.2% berberine in micropropagated and only 0.2% in
the wild).
Silica particles using as stationary phase is now available in various modifications for specific applications in
chromatography like affinity chromatography, ion exchange chromatography and size exclusion chromatography. Of
which affinity chromatography is a technique based on selective non-covalent interaction between an affinity ligand bound
to the stationary phase and the analyte molecule. These affinity ligands like antibodies, enzyme inhibitors etc. selectively
and reversibly bind analyte molecules in the sample which could be eluted later by changing the elution parameters (Skoog
et al., 2007).
Utilising affinity chromatography a study was conducted by Paiva et al. (2003) to separate out trypsin inhibitors
present in Echinodorous paniculatus that could prevent the digestion of proteins. Here, a ligand obtained from another
plant (Carota mollis) which could bind trypsin inhibitor is first coated on to the chromatographic bed and they named it as
Cra Iso 1, 2, 3 – sepharose. When the extract was poured ligand binds the trypsin inhibitors and it is separated out from the
column using salt solution and it is quantified as 1mg protein contains 0.01mg trypsin inhibitor.
Chromatography a Competent Tool for Phytochemical Profiling of Medicinal Plants – A Review 79
www.tjprc.org [email protected]
Another HPLC technique is ion exchange chromatography where the stationary phase is an ion exchange resin.
When the mobile phase passes through the resin, the electrostatically bound ions are released from resin and ions of the
like sign present in the extract got bounded preferentially (Sarzanini, 2002). This technique is most frequently used for the
separation and purification of proteins, polypeptides, nucleic acids, polynucleotides and other charged biomolecules
(Bonnerjera et al., 1986).
Isitua et al. (2015) had used Biochrom 30 an ion exchange chromatography column to separate different
aminoacids present in Moringa oleifera leaves collected from Africa. They had obtained 16 aminoacids with glycine is in
higher amounts (3.63%).
Size exclusion chromatography is yet another unique HPLC technique which uses a porous gel [stationary phase]
to separate the mixture through the column and separation happens according to the particle size. This is used to separate
high molecular mass products like proteins from low molecular mass species like amino acids and small peptides in
pharmaceutical drug preparations (Skoog et al., 2007).
From Solanum aculeatissimum using ion exchange chromatography a protease inhibitor was separated by
Krishnan et al. (2015) and they selected size exclusion chromatography using Sephadex G – 50 as the stationary phase to
purify this protease inhibitor into its components, trypsin inhibitor and chymotrypsin inhibitor. They could separate 285.7U
of trypsin and 270.9U of chymotrypsin from one mg protein (1U means the amount of substrate that can be catalyzed per
minute).
A HPLC system can be run in isocratic mode or in gradient mode. In isocratic elution process for the entire running
of HPLC system only a single mobile phase composition (a single solvent or solvent mixed in a particular ratio) is
delivered to the column using a single pump. In gradient elution, we can change the mobile phase composition using two
or more pumps according to a set programme as like the one which was used by Bhaskara Rao et al. (2015) for analysing
methanolic extract of Kaempferia galanga leaves. They used two solvents (Solvent A: 50mM sodiumphosphate in 10%
methanol and Solvent B: 70% methanol) in different proportions at specific time intervals and reported the presence of
genistein (Rt -778.85), coumaric acid (Rt - 23.82), ferulic acid (Rt - 25.39) and butein (Rt - 79.15).
In HPLC, a variety of separating techniques and column packings are available which make the system highly
efficient and flexible. HPLC can be used as a preparative method as well as a purification technique. This can be connected
with modern sophisticated detector or detectors in series for maximum precision in analysis. Most sample analysis is
carried out at room temperature (ICS – UNIDO, 2008).
The stationary phase of a liquid chromatography column is further refined to a particle size of less than or equal to
2.5µm and delivery of mobile phase at higher linear velocities under very high pressure of 103.5 MPa lead to the
development of an ultra – modern technique called UPLC (Ultra Performance Liquid Chromatography) (Roge et al., 2011).
Compared to HPLC compared to HPLC, resolution, sensitivity, speed of analysis and peak capacity (number of peaks
resolved per unit time in gradient separations) can be extended to new limits, so termed as UPLC (Kumar et al., 2014).
UPLC helps in faster analysis which ultimately result in early drug discovery as reported by Shang et al. (2015) that
they could analyse 17 hot water and methanolic extract of 17 different medicinal plants collected from a province of
Canada by using Acquity BEH C18 UPLC column (1.7µm, 2.1x100mm), 0.1% formic acid in water and 0.1% formic acid
in acetonitrile as mobile phase, at a flow rate of 0.5ml/minute and the sample volume used was only 1µL. They could get
80 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
the entire phytochemical data of these samples within hours whereas it takes days or even weeks in HPLC. More than 4000
metabolites were compared using the chromatograms and used further to fulfil their research objective.
Gas Chromatography
In gas chromatography (GC), a gas is used as mobile phase and stationary phase can be either a solid or a non-
volatile liquid coated on an inert supporting material. The stationary phase is held in a narrow column in an oven while
gaseous mobile phase travels through the column. Here, solutes present in the vapourised samples are separated when its
gets partitioned between mobile gaseous phase and stationary phase. Here, the mobile phase doesn’t interact with the
molecules of the analyte but only transport through the column. This is applicable to complex volatile biochemical entities
thermostable compounds (Adams, 2007).
Gas chromatography run by introducing the sample in liquid or gaseous form with the help of a GC syringe into
the injection port. It gets vaporized at injection port then passes through the column along with continuously flowing
mobile phase, usually H2 and get separated/detected at the detection port maintained by suitable temperature programming.
We can visualize the chromatogram in the computer system using the appropriate software.
Janicsak et al. (2003) have standardised a GC method for routene determination of oleanolic acid and ursolic acid
(triterpene compounds) in five medicinal plant species of Lamiaceae family like Hyssopus officinalis, Marrabium vulgare,
Melissa officinalis, Salvia officinalis and Satureja montana. Of these species, Salvia officinalis recorded maximum amount
of both the acids and Marrabium vulgare had the lowest.
The major advantages of gas chromatography are fast analysis, high resolution, reliable and simple technique
with, accurate quantification by coupling it with sophisticated detectors. But, the technique is suited only to volatile oils.
Since, the temperature of the columns are maintained above or equal to 3800C it is not suited to thermolabile compounds.
Sample preparation is also difficult since, it has to be dissolved in volatile solvents and moreover it’s an expensive process
(Eiceman, 2000).
Supercritical Fluid Chromatography (SFC)
Supercritical fluid chromatography (SFC) is a hybrid technique that combines the best features of gas and liquid
chromatography (Chavan et al., 2013). Here, the mobile phase is a fluid which is above and relatively close to its critical
temperature and pressure. The instrument is similar to a GC or LC which differs only in the mobile phase, a super critical
fluid usually carbon dioxide (critical temperature – 31.30C and critical pressure – 72.90atm) is using (Sairam et al., 2012).
SFC permits the separation and determination of a group of compounds which can’t be conveniently handled by either GC
or LC. Compounds that are nonvolatile/ thermally unstable can’t be handled by GC and those compounds with no
functional groups which failed to detect by spectrometry or electrochemical methods of LC can be detected by SFC (Skoog
et al., 2007). SFC has high throughput used for qualitative and quantitative analysis in drug industry.
Vitamin E a fat soluble vitamin was analysed using SFC in a better way than GC by Naegele (2015). Analysing
by SFC it is found that extra virgin olive oil contains α – tocopherol (184.8mg/kg) only and in virgin olive oil along with
tocopherols, its unsaturated derivatives like tocotrienols both in their α,β,γ and δ isomeric forms were present which
indicates the purity of extra virgin olive oil. Compared to LC and GC, SFC is 5 – 10 times faster and with better resolution
(5 times). Compounds with high molecular weight, thermolabile, non-volatile, polar and adsorptive in nature can be
analysed using SFC. Moreover the solvent is not at all harmful.
Chromatography a Competent Tool for Phytochemical Profiling o
www.tjprc.org
HYPHENATED CHROMATOGRAPHY TECHNIQUES
In all the modern chromatography techniques, separated fractions from the column are connected to detectors.
Today, several sophisticated detectors working on specific principles are available like, MS (Mas
(Diode Array Detector) and NMR (Nuclear Magnetic Resonance Detector) etc. which are possible to give additional
information on the separated components (Kamboj, 2012). Of these detectors, MS (Mass Spectrometry) is widely used for
phytochemical analysis and is usually fo
The separated components of the mixture from the chromatograph will enter into the MS through an interphase.
This is followed by ionization, mass analysis and detecti
the mass spectrometer (Van, 2005). The process of ionisation not only ionise the molecule but also break the molecule into
the fragments and detect these fragments with the help of electron
molecular ion of analyte form a finger print spectrum which is different from other analytes (Phalke and Kavade, 2013).
These will be compared with the online library of molecules or library maintained by
elemental composition etc. Thus, MS helps in quantifying the known compounds, identifying the unknown compounds and
also, elucidating the structure and chemical properties of the components.
A typical mass spectrum (Figure 2)
given ion (for singly charged ions this corresponds to the mass of the ion). Height of peak indicates the relative abundance
of a given ion (not reliable for quantitati
Liquid chromatography-mass spectrometry (LC
separation capabilities of liquid chromatography with the mass analysis capabilities of mass spectrometry. LC
powerful technique used for many app
Steenkamp et al. (2004) reported that LC
was detected when the viscera samples of a dead body wa
conclude that the man died out of Datura poisoning, due to the consumption of
GC–MS was the first successful online combination of chromatography with mass spectrometry, an
used in the analysis of essential oil in herbal medicines. With the GC
the information related to qualitative and quantitative composition
establishing the relationship between different
today for the analysis of the volatile chemical compounds in herbal medicines (Gong
made between 2 varieties of Kacholam (
or Phytochemical Profiling of Medicinal Plants – A Review
HYPHENATED CHROMATOGRAPHY TECHNIQUES
In all the modern chromatography techniques, separated fractions from the column are connected to detectors.
Today, several sophisticated detectors working on specific principles are available like, MS (Mas
(Diode Array Detector) and NMR (Nuclear Magnetic Resonance Detector) etc. which are possible to give additional
information on the separated components (Kamboj, 2012). Of these detectors, MS (Mass Spectrometry) is widely used for
chemical analysis and is usually found attached with the LC as LC-MS, GC-MS, SFC-MS etc.
The separated components of the mixture from the chromatograph will enter into the MS through an interphase.
This is followed by ionization, mass analysis and detection of mass-to charge ratios of ions generated from each analyte by
The process of ionisation not only ionise the molecule but also break the molecule into
the fragments and detect these fragments with the help of electron impact ionisation and/or chemical ionization. The
molecular ion of analyte form a finger print spectrum which is different from other analytes (Phalke and Kavade, 2013).
These will be compared with the online library of molecules or library maintained by the system for getting its structure,
elemental composition etc. Thus, MS helps in quantifying the known compounds, identifying the unknown compounds and
also, elucidating the structure and chemical properties of the components.
(Figure 2) is characterized by sharp, narrow peaks. X-axis indicates the m/z ratio of a
given ion (for singly charged ions this corresponds to the mass of the ion). Height of peak indicates the relative abundance
of a given ion (not reliable for quantitation). Peak intensity indicates the ion’s ability to desorb.
Figure 2: A Typical Mass Spectrum
mass spectrometry (LC-MS) is an analytical technique that combines the physical
separation capabilities of liquid chromatography with the mass analysis capabilities of mass spectrometry. LC
powerful technique used for many applications which has very high sensitivity and selectivity (Wang
. (2004) reported that LC-MS analysis could help in forensic study also since, scopolamine and atropine
was detected when the viscera samples of a dead body was analysed using this technique
conclude that the man died out of Datura poisoning, due to the consumption of Datura stramonium
MS was the first successful online combination of chromatography with mass spectrometry, an
used in the analysis of essential oil in herbal medicines. With the GC–MS, not only a chromatographic fingerprint but also
the information related to qualitative and quantitative composition is made possible. This will be extremely useful for
different constituents and its pharmacology. Thus, GC–
for the analysis of the volatile chemical compounds in herbal medicines (Gong et al
rieties of Kacholam (Kaempferia galanga) for its volatile oil constituents using GC
81
In all the modern chromatography techniques, separated fractions from the column are connected to detectors.
Today, several sophisticated detectors working on specific principles are available like, MS (Mass Spectrometry), DAD
(Diode Array Detector) and NMR (Nuclear Magnetic Resonance Detector) etc. which are possible to give additional
information on the separated components (Kamboj, 2012). Of these detectors, MS (Mass Spectrometry) is widely used for
MS etc.
The separated components of the mixture from the chromatograph will enter into the MS through an interphase.
to charge ratios of ions generated from each analyte by
The process of ionisation not only ionise the molecule but also break the molecule into
impact ionisation and/or chemical ionization. The
molecular ion of analyte form a finger print spectrum which is different from other analytes (Phalke and Kavade, 2013).
the system for getting its structure,
elemental composition etc. Thus, MS helps in quantifying the known compounds, identifying the unknown compounds and
axis indicates the m/z ratio of a
given ion (for singly charged ions this corresponds to the mass of the ion). Height of peak indicates the relative abundance
on). Peak intensity indicates the ion’s ability to desorb.
MS) is an analytical technique that combines the physical
separation capabilities of liquid chromatography with the mass analysis capabilities of mass spectrometry. LC-MS is a
lications which has very high sensitivity and selectivity (Wang et al., 2001).
MS analysis could help in forensic study also since, scopolamine and atropine
analysed using this technique. This aided the doctors to
Datura stramonium seeds.
MS was the first successful online combination of chromatography with mass spectrometry, and is widely
MS, not only a chromatographic fingerprint but also
. This will be extremely useful for
–MS is the most preferable tool
et al., 2001). A comparison was
) for its volatile oil constituents using GC – MS by Indrayan et
82 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
al. (2007) and reported that 58 compounds were identified from variety Kasthuri and 56 from Rajani. 45 compounds are
found common for both. 13 compound are peculiar to Kasthuri and is not present in Rajani. The major component
responsible for aroma in Kacholam, ethyltrans – p - methoxycinnamate is quantified to be 39% in Kasthuri and only 35%
in Rajani. So, Kasthuri is recommended for volatile oil production.
Chromatography is still competent by hyphenating it with another competent spectrometry called tandem mass
spectrometry which helps to analyze only selected specific ions of your interest by filtering out the untargeted ions.
Chromatography combined with MS – MS technique take the advantage of chromatography as a separation method and
MS - MS as a most precise identification method. MS - MS can provide on-line information for each individual peak in a
chromatogram. With the help of this hyphenation, in most cases, one could identify the chromatographic peaks directly on-
line by comparison with standard compounds, which made the MS–MS a powerful approach for the rapid identification of
phytochemical constituents. In phytochemical research, this is usually done to find out the presence of any trace elements
or heavy metals like mercury, lead etc. in the sample (Nair et al., 2010).
Here, two mass spectrometers are arranged one in front of the other (in tandem) separated by a collision cell. In
the first MS – ions of your interest, suppose mercury in your sample only will be filtered and allowed to enter the collision
cell where, it is collided with Argon or Nitrogen gas so that ions get fragmented. These ions are again filtered using the
second MS according to their m/z (mass/charge) ratio. Filtering can be done by several ways mainly according by
adjusting the frequency of oscillation of electric current according to the mass and charge of ions. Finally, the target ions
will be detected by a detector and quantified and a mass spectrum of specific ions only will be obtained (Prasain, 2012)
(Figure 3).
Figure 3: Principle of Tandem Mass Spectrometry
Paris polyphylla, a medicinal plant of Himalayas is rich in steroidal saponins like diosgenyl and pennogenyl
saponins which are proved to be successful against several human cancer cell lines. A study was done by Kumar et al.
(2014) to identify the presence of these two compounds in Paris polyphylla, for using it in a study against human lung
cancer cell lines. They developed HPLC chromatograms also, MS – MS spectra for each Rt values and reported the
presence of several pennogenyl and diosgenyl saponins in the Rt ranges 1.4 to 2.3 and 9.3 to 14.03 respectively.
CONCLUSIONS
Chromatography is a physical method of separation in which the components of a plant extract are separated
between a mobile phase and a stationary phase. It has a wide array of technical advancement which revolutionized
phytochemical research. It is a multidisciplinary tool which helps to identify the presence of some specific compounds
(qualitative analysis) which aid finding out the adulterants present in the pharmaceutical preparations, authentication of
herbal products as well as can sometimes act as a chemotaxonomical tool. Quantitative analysis can also be made with the
use of sophisticated techniques like HPTLC, HPLC, UPLC, GC, SFC etc. which are effective and reliable tools in the
Chromatography a Competent Tool for Phytochemical Profiling of Medicinal Plants – A Review 83
www.tjprc.org [email protected]
entire chain of development of products like dietary supplements, nutraceuticals and various types of medicines. It is used
in quality control, purity check, clinical applications, metabolism studies, drug screening etc. Chromatography becomes
more competent when it is hyphenated with sophisticated detectors like mass spectrometry, tandem mass spectrometry etc.
which are capable of giving much more information about the components separated out using chromatography. The
molecular mass, structural elucidation of the compound etc. are made possible by using spectrometry whereas trace
compound analysis can be done using tandem mass spectrometry. Research is focused on development of new
chromatographic techniques and its hyphenations with more sophisticated detectors for enhancing the accuracy and
precision of phytochemical analysis.
REFERENCES
1. Adams, R. P. (2007). Identification of Essential oil Components by Gas Chromatography/ Mass Spectrometry. Allured
Publications Corporation, Suite A, Carol Stream, USA, 804p.
2. Archana, A., Bele & Khale, A. (2011). An overview on thin layer chromatography. International Journal of Pharmaceutical
Sciences and Research, 2(2), 256 – 267.
3. Bhaskara Rao, K. V., Kaushika, B. & Priya, L. C. (2015). HPLC analysis and antioxidant activities of hydroethanolic leaf
extract of Kaempferia galanga L. International Journal of Pharmtech Research, 7(2), 422 – 431.
4. Bilia, A. R., Bergonzi, M. C., Lazari, D. & Vincieri, F. F. (2002). Characterisation of commercial kava – kava herbal drug and
herbal drug preparations by means of nuclear magnetic resonance spectroscopy. Journal of Agricultural and Food Chemistry,
50 (18), 5016 - 5025.
5. Bonnerjera, J., Oh, S., Hoare, M. & Dunhill, P. (1986). The right step at the right time. Bio Technology, 4, 954 – 958.
6. Calixo, J. B. (2000). Efficacy, safety, quality control, marketing and regulatory guidelines for herbal medicines
(Phytotherapeutic agents). Brazilian Journal of Medical and Biological Research, 33(2), 179‐189.
7. Charde, M. S., Welankiwar, A. S. & Kumar, J. (2014). Method development by liquid chromatography with validation.
International Journal of Pharmaceutical Chemistry, 4(2), 57 – 61.
8. Chavan, M., Sutar, M. & Deshmukh, S. (2013). Significance of various chromatographic techniques in drug discovery and
development. International Journal of Research in Pharmacy and Chemistry, 3(2), 282-289.
9. Devare, S. M., Kamble, G. S., Torane, R. C., Kale, A. A., Deshpande, N. R. & Salvekar, J. P. (2011). Preliminary screening of
aminoacids from a medicinal plant: Morinda pubescence. Journal of Chemical and Pharmaceutical Research, 3(3), 192-195.
10. Devi, S. L. & Devakar, M. C. (2012). Pharmacognostical evaluation of the leaves of Wrightia tinctoria (Roxb) R. Br. Hygeia
Journal for Drugs and Medicines, 4(1), 104 – 111.
11. Eiceman, G. A. (2000). Gas chromatography. In: Meyers, R. A. (ed.). Encyclopedia of Analytical Chemistry: Applications,
Theory and Instrumentation. Chichester: Wiley, 10627p.
12. Gillard, J. A. & Ritter, C. (1997). Use of simulated liquid chromatography – diode array detection data for the definition of a
guide curve in peak purity assessment by spectral comparison. Journal of Chromatographia A, 786(1), 1 -11.
13. Gong, F., Liang, Y. Z., Cui, H., Chau, F. T. & Chau, B. T. P. (2001). Determination of volatile components in peptic powder
by Gas Chromatography- Mass Spectrometry and Chemometric resolution, Journal of Chromatographia. A, 909: 237-247.
14. Gupta, M. M. & Shanker, K. (2008). Process-scale high performance liquid chromatography for medicinal and aromatic
plants. In: Khanda, S. S., Singh Khanuja, S. P., Longo, G. and Rakesh, D. D. (eds), Extraction Technologies for Medicinal and
84 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
Aromatic Plants. International Center for Science and High Technology, Trieste, Italy, 260p.
15. Huynh-Ba, K. (2009). Handbook of Stability Testing in Pharmaceutical Development. Springer Verlag, NewYork, 369p.
16. ICS – UNIDO (International Center for Science and High Technology United Nations Industrial Development Organisation).
(2008). Extraction Technologies for Medicinal and Aromatic Plants. Handa, S. S., Singh, S. P., Longo, K. G. and Rakesh, D.
D. (eds.), ICS – UNIDO Trieste, Italy, 266p.
17. Indrayan, A. K., Kuriya, A., Tyagi, P. K., Shatru, A. & Rathi, A. K. (2007). Comparative chemical study of two varieties of
attractive medicinal plant Kaempferia galanga Linn. Natural Product Radiance, 6(4), 327 – 333.
18. Isitua, C. C., Lozano, M. J. S., Jarimillo, C. J.& Dutan, F. (2015). Phytochemical and nutritional properties of dried leaf
powder of Moringa oleifera Lam. From Machala el oro province of Ecaudor. Asian Journal of Plant Science and Research,
5(2), 8 – 16.
19. IUPAC (International Union of Pure and Applied Chemistry). (2006). Compendium of Chemical Terminology - The Gold Book
[e – book]. McNaught, A. D. & Wilkinson, A. (eds.), Blackwell Scientific Publications, Oxford. Retrieved from
http://goldbook.iupac.org. [24 Feb. 2014].
20. Janicsak, G., Veres, K., Kallai, M. & Mathe, I. (2003). Gas chromatographic method for routine determination of oleanolic
and ursolic acids in medicinal plants. Chromatographia, 58, 295 – 299.
21. Jirge, S. S. (2011). Standardisation of some plant based formulations by modern analytical techniques. PhD. Pharmacy thesis,
S. N. D. T. Womens University, Mumbai, 408p.
22. Kamboj, A. (2012). Analytical evaluation of herbal drugs. In: Vallisuta, O. & Olimat, S. M. (eds.), Drug Discovery Research
in Pharmacognosy. InTech Publishers, 254p. Retrieved from http://www.intechopen.com/books/drug-discovery-research-in
pharmacognosy/analytical-evaluation-of-herbaldrugs.
23. Khyade, M. S. & Vaikos, N. P. (2014). Wrightia tinctoria R. Br. A review on its ethanobotany, pharmacognosy and
pharmacological profile. Journal of Coastal Life Medicine, 2(10), 826 – 840.
24. Krishnan, M. V. G., Manoj, G. S. & Murugan, K. (2015). Anti-haemolytic, anti-lipid peroxidative potential by purified
protease inhibitors from the fruits of Solanum aculeatissimum Jacq. in human erythrocytes against hydrogen peroxide.
Journal of Pharmacognosy and Phytochemistry, 4(3), 203 – 208.
25. Kumar, H. M., Dhiman, V., Choudhary, R. & Chikara, A. (2014). Anticancerous activity of hydroalcoholic extracts from Paris
polyphylla rhizomes against human A549 lung cancer cell lines using MTT assay. International Research Journal of
Pharmacy, 5(4), 290 – 294.
26. Kumar, J. & Dhillon, H. (2015). TLC profiling and phytochemical screening of Podophyllum hexandrum Royle. an
endangered medicinal plant. International Journal of Farm Sciences, 5(1), 56 – 61.
27. Kumar, S., Jyothirmayee, K. & Sarangi, M. (2013). Thin layer chromatography: A tool of biotechnology for isolation of
bioactive compounds from medicinal plants. International Journal of Pharmaceutical Sciences Review and Research, 18(1),
126 – 132.
28. Kustrin, S. A. & Hettiarachchi, C. G. (2014). Quantitative High Performance Thin Layer Chromatography for the analysis of
herbal medicines: Problems and advantages. Modern Chemistry and Applications, 2(1), e118.
29. LC-GC Europe. (2003). M. S. Tswett and the Invention of Chromatography. Ettre, L. S. (ed.), Department of Chemical
Engineering, Yale University, New Haven, Connecticut, USA, 7p.
Chromatography a Competent Tool for Phytochemical Profiling of Medicinal Plants – A Review 85
www.tjprc.org [email protected]
30. Mahesh, A., Mueen Ahmed, K. K., Aldhubaid, B. E. & Harsha, S. (2011). High performance thin layer chromatography: A
powerful analytical technique in pharmaceutical drug discovery. Pharmaceutical methods – an addendum to Journal of Young
Pharmacist, 2(2), 71 – 75.
31. Mehta, S. J., Shah, D. P., Mehta, T. J., Patel, P. M. & Patel, N. M. (2011). Compendial testing method on herbal crude drug –
a review. Asian Journal of Pharmaceutical Research, 1(2), 49-52.
32. Miller, M. J. (2005). Chromatography: Concepts and Contrasts (2nd edition). John Wiley & Sons, Hoboken, New Jerssy, 490p.
33. Muruganandham, A. V., Bhattacharya, S. K. & Ghosal, S. (2000). Indole and flavonoid constituents of Wrightia tinctoria,
Wrightia tomentosa and Wrightia coccinea. Indian Journal of Chemistry, 39B, 125 – 133.
34. Naegele, E. (2015). Determination of vitamin E in olive oil using the agilent 1260 infinity analytical SFC system [online].
Retrieved from http://www.agilent.com/chem.
35. Nair, A., Devanshu, S., Rahul, M., Annu, G. & Kishan, S. (2010). Quantitative bioanalysis by LC-MS/MS. A review. Journal of
Pharmaceutical and Biomedical Sciences, 7(7), 1 – 9.
36. Paiva, P. M. G., Souza, A. F., Oliva, M. L. V., Kennedy, J. F., Cavalcanti, M. S. M., Coelho, L. C. B. B. & Sampaio, C. A. M.
(2003). Isolation of a trypsin inhibitor from Echinodorous paniculatus seeds by affinity chromatography on immobilized
Cratylia mollis isolectins. Bioresource Technology, 88, 75 – 79.
37. Patel, R. B. & Patel, M. R. (2008). An introduction to analytical method development for pharmaceutical formulations.
Pharmacological Reviews, 6(4), 1- 5.
38. Patil, P. S. & Shettigar, R. (2010). An advancement of analytical techniques in herbal research. Journal of Advanced Scientific
Research, 1(1), 8-14.
39. Patil, S., Nivsarkar, M. & Anandajiwala, S. (2013). Isolation and TLC densitometric quantification of lysergol from the seeds
of Ipomoea muricata Linn. Jacq. Ethanobotanical Leaflets, 10, 336 – 341.
40. Phalkae, P. & Kavade, S. (2013). Review on hyphenated techniques. International Journal of Chemical Studies, 1(3), 157 –
165.
41. Prasain, J. K. (2012). Tandem Mass Spectrometry – Applications and Principles. InTech Publishers, 788p. Retrieved from
http://www.intechopen.com/books/umac.mo/e-books.
42. Revathy, S., Elumalai, S., Benny, M. & Antony, B. (2011). Isolation purification and identification of curcuminoids from
turmeric (Curcuma longa) by column chromatography. Journal of Experimental Sciences, 2(7), 21 – 25.
43. Roge, A. B., Firke, S. N., Dhane, R. M., Gunjkar, V. J. & Vadvalkar, S. M. (2011). Achievement of HPLC: UPLC. International
Journal of PharmTech Research, 3(3), 1423 – 1429.
44. Saenego, C. T. & Ndip, R. N. (2012). Identification and antibacterial evaluation of bioactive compounds form Garcinia kola
(Heckal) seeds. Molecules, 17, 6569-6584.
45. Sairam, P., Ghosh, S., Jena, S., Rao, K. N. V. & Banji, D. 2012. Super critical fluid extraction – An overview. Asian Journal of
Research in Pharmaceutical Sciences, 2(3), 112-120.
46. Sarzanini, C. (2002). Recent developments in ion chromatography. Elsevier Journal of Chromatography, 956, 3 – 13.
47. Sethi, P. D. (2013). Sethis’s HPTLC – Quantitative Analysis of Pharmaceutical Formulations. CBS Publishers and
distributors, New Delhi, 1288p.
86 Sonia, N. S. & Jessykutty, P. C.
Impact Factor (JCC): 5.4638 NAAS Rating: 3.54
48. Shang, N., Saleem, A., Musallam, L., Walshe-Roussel, B., Badawi, A., Cuerrier, A., Arnason, J. T. & Haddad, P. S. (2015).
Novel approach to identify bioactive plant metabolites: Pharmacological and metabolomics analyses of ethanol and hot water
extracts of several Canadian medicinal plants of the Cree of Eeyou of Istchee. Plos One, 10(8), e0135721.
49. Singh, N. & Kumar, S. (2015). TLC and HPLC finger print development of Aegle marmelos Corr. and its polyherbal marketed
formulation. International Journal of Pharmaceutical Sciences and Research, 6(1), 161 – 167.
50. Singhal, S., Singhal, N. & Agarwal, S. (2009). Thin Layer Chromatography. In: Kasture, A. V., Mahadik, K. R., Wadodkar, S.
G and More, H. N. (eds.), Pharmaceutical analysis – Instrumental Methods – Vol. ii (1st edition), Nirali Prakashan, 270p.
51. Sivakumar, V., Sadiq, A. M., Danarajan, M. S.& Jayanthi, M. (2014). HPLC method for quantification of berberine in wild
and micropropagated Tinospora quardifolia – an important ayurvedic medicinal plant. International Journal of
Pharmaceutical Research Scholars, 3(2), 432 – 439.
52. Skoog, D. A., Holler, F. J. & Nieman, T. A. (2007). Principles of Instrumental Analysis (5th Ed.). Saunders College Publishing,
Philadelphia, 1056p.
53. Srivastava, M. M. (2011). High Performance Thin Layer Chromatography (HPTLC). Springer, Verlag Berlin, Heidelberg,
60p.
54. Steenkamp, P. A., Harding, N. M., Van Heerden, F. R. & Van Wyk, B. E. (2004). Fatal Datura poisoning: identification of
atropine and scopalamie by high performance liquid chromatography/ photo diode array/ mass spectrometry. Forensic
Science International, 145, 31 – 39.
55. The Royal Society of Chemistry. (1997). Modern Chemical Techniques [e-book] Faust, B. (ed.), Unilever publications, UK.
Retrieved from http://www.rsc.org/images/modern_chemical_techniques_tcm-18 -189696.pdf.
56. Van Galen, P. M. (2005). Mass spectrometry at the organic chemistry department: A guide for novel users [online]. Retrieved
from http://www.ru.nl/publish/pages/580561/msdictaat.pdf.
57. Wang, Y., Sheng, L. S. & Lou, F. C. (2001). Analysis and structure identification of trace constituent in the total ginkgolide by
using LC/DAD/ESI/MS. Yao Xue Xue Bao, 36, 606-608.
58. WHO [World Health Organisation]. (2008). Essential Medicines and Health Products Information Portal: A World Health
Organisation Resource [online]. Retrieved from http://www.who.int/medicinedocs/en/d/jh2945e/4.html.
59. Wilson, I. D. (2000). Paper chromatography. In: Encyclopedia of Separation Science. Academic Press, New York, 397 - 404p.