Download - 8ft Antenna (HTT81.221-10)
-
8/13/2019 8ft Antenna (HTT81.221-10)
1/15
Sales department : Radio Frequency Systems GmbH
Kabelkamp 20, D-30179 Hannover (Germany) Tel. +49-511 676-25 20 Fax +49-511 676-25 21
Plant: RFS France Trignac Fax +33 02 40 90 41 43 1/15
Installation Instructions
8 ft Antennas
PA, PAL, PAD, PAX, PADX
DA, UA, DAX, UDA, UXA HTT 81.221-10(e)
These Installation Instructions are valid for antennas in the following version :
Reflector 2.4 m (8 ft)
Waveguide feed system Singleor Dualpolarized
Pipe mount for installation on pipe 115mm
Antenna offset to the left or the right
Safety collar for easy installation
2 spindles for fine adjustment ofAzimuth & Elevationof 5
1 sway bar 60 mm x 3 m
Reflector with shroud, the aperture covered by aflexible planar radome, or without
shroud (see sketch above)
Note : The assembly of the reflector and shroud for antennas with split
reflector is described in the dedicated Installation Instructions.
DA, UA, DAX, UDA, UXA PA, PAL, PAD, PAX, PADX
It is important to mount the antenna exactly as described in this installation instruction.The installed antenna shall be inspected once per year by qualified personnel.
RFS disclaims any responsibility for the result of improper or unsafe installation.This installation instruction has been written for qualified skilled personnel.We reserve the right to alter details, especially with respect to technical improvement.
-
8/13/2019 8ft Antenna (HTT81.221-10)
2/15
HTT 81.221-10 (e) 2/15
1. Tools required for installation(Tools are not included with antenna)Hoisting device for 400 daN Shackle
Torque wrench from 0,5 to 25 daNm 2 ropes
Wrenches for hexagon bolts: Mallet
M5(8), M6(10), M10(17), M12(19) Water balance and compass
M14(21), M16(24), M20(30) Square
(values in brackets = openings of spanners)
2. Assembly of the mount(For an installation offset right)For easy operation of the bolted joints, and correct torque tightening, Anti Seize Installation Paste must be applied to all threads of bolts and fine adjustment spindles.After this, keep the lubricated threads free of dust and dirt! (a Torque Table is attachedfor specifications)
Left-L
4 U-bolts M148 washers 1516 nuts M14
Fine AZIMUTM20x300 spindle4 washers 214 nuts M20
Right-L
U-bracket swaybarScrew M20x110Washer 21SL washer 20Nut M20
Screw M20x502 washers 21SL washer 20Nut M20
Fine ELEVATIONSpindle M16x3002 brass nuts M16
2 spherical washers C172 conical seats D19
2 washers 17 50
Screw M16x50Washer 17
SL washer 16Nut M16
2 screws M12x45
2 washers 13 372 SL nuts M12
Screw M20x502 washers 21SL washer 20
Nut M20
Screw M20x502 washers 21SL washer 20Nut M20
4 screws M12x408 washers 13
4 SL nuts M12
Plate Az. Adjust. Support2 U-bolts M124 washers 13
8 nuts M12
Screw M20x60Washer 21SL washer 20Nut M20
Bracket sway bar fixingScrew M20x50Washer 21SL washer 20Nut M20
U-bolt M12Angle Az. Adjust.2 washers 134 nuts M12
Safetyangle
2 screws M12x45
2 washers 13 372 SL nuts M12
3 obturation plastic plugs(to install in backring holes)
Site-L2 screws M12x45
2 washers 13 372 SL nuts M12
-
8/13/2019 8ft Antenna (HTT81.221-10)
3/15
HTT 81.221-10 (e) 3/15
3. Antenna with split reflector
If you have ordered an antenna with a split reflector, refer to specific installation instructionsjoined for reflector & backring assembly, otherwise skip this step.
4. Brackets installation on backring
2 screws M12x45
2 screws M12x45
Hoisting eyeat the Top
Washer 13 37Washer 132 SL nuts M12
Before starting the installation of the brackets on the backring, install the antennareflector on a thick cardboard or wooden planks to protect the antenna during theassembly (or the antenna top packing case for e.g.).
Backring
Reflector
Zone freeof paint
(grounding)
2 screws M12x45Washer 13 37Washer 13
Rightbracket
(L70x70) 2 SL nuts M122 washers 13 37
Elevation bracket(L100x75)Take care of theorientation
Leftbracket
(L70x70)
Zone freeof paint
(grounding)
2 SL nuts M122 washers 13 37
-
8/13/2019 8ft Antenna (HTT81.221-10)
4/15
HTT 81.221-10 (e) 4/15
Sway barattachment
Offset left Offset Right
Sway barattachment
It is mandatory to tighten all bolted joints of the mount accordingto the torque table joined, before lifting the antenna.
Screw M20x502 washers 21SL washer 20
Nut M20
Screw M20x502 washers 21SL washer 20Nut M20
Spindle M16x300Brass nuts M16
Spherical washers C17Conical seat D19
Conical seat D19Spherical washers C17Brass nuts M16
2 screws M12x402 washers 13
2 screws M12x402 washers 13
2 washers 132 SL nuts M12
2 washers 132 SL nuts M12
2 screws M12x45
2 washers 13 372 SL nuts M12
Vertical bracket8/114 STD
Bracket elevation adjust8-10/114 STD
(L100x100
Horizontal bracket8/114 STD
5. Pre-assembly of the T-Mount & Antenna Offset
T-Mount Pre-assembly(for an offset Right)
(Rear view)for an offset right
Notch atthe top
After perpendicularitycheck between the 3 parts
of the T-Mount, torquetighten the M12 bolts to
lock the assembly.(Without square, you can
help you with a sheet of
Install the 3 plastic
caps to close the100 mm holes on
the backring
-
8/13/2019 8ft Antenna (HTT81.221-10)
5/15
HTT 81.221-10 (e) 5/15
6. Installation of the shroud panels(for antennas with shroud)
6.36.1 6.2
(Short panel length)7 hex screws M6x16
14 washers 6.4 187 sl nuts M6
(Long panel length)8 hex screws M6x16
16 washers 6.4 188 sl nuts M6
3 Stiffener plates with :
4 hex screws M6x25
8 washers 6.4 18
4 sl nuts M6
Do not tighten all jointsbefore complete shroud
installation. See chapter 6.4for RF braid installation.
x3x3
Reflector / Shroudpanels assembly
Shroud panelsassembly
Shroud panelsreinforcement
assembly
- Install the reflector equipped with its mount on woodenbeams (to not damage mount parts with the ground) andkeep bolt threads free of dust.
- The reflectors rim and the shroud panels must be clean and
dry.
- Dismount the hoisting eye of the reflector (installed at factory)
- For the antennas ordered with a 250 km/h WindKit, if the 6galvanized steel pipes have been pre-installed in factory atreflectors back, you need to remove the 6 M20 bolts (locatedat the reflectors rim), before shroud panels installation, andre-use it for the assembly of the reflector/shroud junction at13 holes in front of the galvanized steel pipes (instead ofthe M6x25 bolts provided with the antenna).
(Standard Installation)30 hex screws M6x25
60 washers 6.4 18*30 sl nuts M6
* for spots free of paint 90from TOP (left & right) add 2
serrated lock washers A6.4
(With 250 km/h WindKit)18 hex screws M6x25
36 washers 6.4 18*18 sl nuts M6
+6 hex screws M12x40
12 washers A136 SL washers 12
6 nuts M12
-
8/13/2019 8ft Antenna (HTT81.221-10)
6/15
HTT 81.221-10 (e) 6/15
6.4 RF Braid installation between shroud & reflector rim(for antennas with shroud)
7. Hoisting eye re-installation(for antennas with shroud)
8. Radome protection installation on shroud rim(for antennas with shroud)
Shroud rim
Edgeprotector
Hoistingeyes
2 screws M12x352 washers 132 SL washers4 nuts M12
Shroud
Reflector
(Top View)
Shroud
Reflector
- Squeeze the clip onto the RFbraid, then hook it onto boltbetween the reflector and ashroud rim
- Overlap the RF braid ends - Removed spacers, and tightenall the bolts
-
8/13/2019 8ft Antenna (HTT81.221-10)
7/15
HTT 81.221-10 (e) 7/15
9. Feed Installation(for customized antennas, see specific Feed Install. Instructions joined)The feed is a precision component which should be handled with special care duringinstallation. For instance, always carry the feed, supporting casting plate side. Any damagemay degrade the antennas performance. Repair of feeds is not possible in the field.
9.1 Polarization choice
Single polarization
Dual polarization
9" FeedSystem
(rear view)
TOP Antenna
14.5" FeedSystem
(rear view)
TOP Antenna
Antennavertical
axis
9" FeedSystem
(rear view)
- Unscrew the 4 screws M6- Carefully rotate the feed of 90- Lock the 4 screws M6
Verticalpolarization
Horizontalpolarization
TOP AntennaTOP Antenna
- Unscrew the 8 screws M6- Carefully rotate the feed of 90- Lock the 8 screws M6
14.5" FeedSystem
(rear view)Vertical
polarizationHorizontal
polarization
TOP AntennaTOP Antenna
Antennavertical
axis
-
8/13/2019 8ft Antenna (HTT81.221-10)
8/15
HTT 81.221-10 (e) 8/15
9.2 Guy wires assembly
9.3 Polarization fine adjustment
The final adjustment will be made after the antenna installation on tower
Insert the 3 guy wires in the mounting holesfrom the rearof the reflector.
Move the feed assembly partway through theconnecting ring.
Hook the guy wires into rotatable ring.
Move the feed and fix it, with the M6 screws inthe connecting ring.
Spring compression5 mm Maxi
Rotatablering
Staying withspring system
Same staying tensionon each guy wi res
Reflector
After control that each guy wires havethe same tension, lock the 2
ndM8 nut
on the 1stone with another wrench,
keeping the first nut in his position.
Check the feed system possiblerotation (H or V polarization)
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Polar.Adjust.
Loosen the 4 screws M6
and adjust polarization byrotation of the feed system
9" Feed System(rear view)
Loosen the 8 screws M6
and adjust polarization byrotation of the feed system
14.5" Feed System(rear view)
Antennavertical
axis
Single polar.Feed system
Dual polar.Feed system
Single polar.Feed system
Dual polar.Feed system
-
8/13/2019 8ft Antenna (HTT81.221-10)
9/15
HTT 81.221-10 (e) 9/15
10. Installation of the planar radome(for antennas with shroud)Take care to avoid kinking of planar radomes during installation. Kinking will destroy theradomes, which are non-repairable
11. Sway bar assembly(for an offset Right)
After sway bar pipe installation, beforeantenna hoisting on the tower, attach thesway bar in vertical position at the elevationspindle with a small rope, to avoid possibleshock.
For an easier sway bar orientation, keepthe U-bracket sway bar free in rotationwithout gap until sway bar final attachmentto the tower. At this time, all bolted jointswill be torque tighten.
- Unpack the radome and carefully strech it over the shroud aperture- For radomes with RFS logo, align it with the vertical axis of the antenna
- For radomes without RFS logo, the central air vent mosquito net aperture must be oriented towardsthe antenna top
- Attach J-bolt with springs and smooth radome down as the springs are attached, but do notdisplace the edge protector on the shroud rim.
- Align the length of the springs to approximately 135 mm at each J-bolt, this will provide properradome tension.
U-Bracket sway bar installation Sway bar pipe installation
U-bracket sway bar
Washer 21Screw M20x50
Nut M20SL washer 20Washer 21
ScrewM20x110
Washer 21SL washer 20
Nut M20
Air ventdetail
Air vent mosquito net must be
oriented towards top antenna,and inside of the shroud
RFS logo towardsthe antenna top
J-bolt
Spring
Radome
135 mm
Shroud
-
8/13/2019 8ft Antenna (HTT81.221-10)
10/15
HTT 81.221-10 (e) 10/15
12. Azimuth fine adjustment spindle pre-assembly(Handtighten)
4 Nuts M122 washers 13
8 Nuts M124 washers 13
Nut M20SL washer 20Washer 21
Screw M20x50
Nut M20Washer 21
Nut M20Washer 21
Screw M20x60
Washer 21SL washer 20
Nut M20(Installed at sway bar
attachment time on thetower structure)
Sway bar fixing clamp(L100x100)
M20x300Azimuth spindle
2 U-bolts M12(keep 60 mm space for
sway bar pipe insertion)
U-bolt M12(keep 60 mm space forsway bar pipe insertion)
Nut M20Washer 21
Nut M20Washer 21
Plate AzimuthAdjust Support 60
(5 holes)
Angle towerstructure
Sway bar pipeextremity
Typical sway bar installation on
tower with angle structure
Optional sway bar kit for sway bar
installation on tower with pipe structure
Sway bar Kit Option :
SMA-SKO-60 (pipe 60)SMA-SKO-89 (pipe 89)SMA-SKO-114 (pipe 114)
Sway bar pipeextremity
Pipe towerstructure
SMA-SKO-6089 or 114
Angle Az. Adjust. 60(L100x75)
Plate Azimuth Adjust
Support 60 (6 holes)(Provided with kit)
-
8/13/2019 8ft Antenna (HTT81.221-10)
11/15
HTT 81.221-10 (e) 11/15
13. WindKit Installation
If you have order a 250 km/h WindKit, refer to specific installation instructions joined, otherwiseskip this step.
14. Safety collar installation on tower pipe support
15. Hoisting on Tower
Before antenna hoisting on the pylon, verify that all the bolted joint of the T-Mountstructure on the antenna have been torque tighten, otherwise the installation on thepipe support could be problematic.
U-bolt
M14
2 washers 154 nuts M14
200 mmminimumfree spaceabove U-bolt
950 mmminimumfree spaceunder U-bolt
Angle safetysupport
Lifting strap (or a rope) fixed on thehoisting eye to keep the antennastreight (in horizontal line)
Lifting strap fixed onthe mount (steel partof the antenna)
Lifting strap fixed on themount (steel part of the
antenna)
Sway bar attached with a ropeto elevation spindle beforestarting the antenna hoisting
Steel eye fixed on themount with the liftingstrap (it will received asecond rope to avoid anyturning, due to wind e.g)
Strong rope or cablelinked to winch
Steel roll or shackle
Strong rope or cablefixed to antenna mount
to avoid collision withthe tower structure
during hoisting
-
8/13/2019 8ft Antenna (HTT81.221-10)
12/15
HTT 81.221-10 (e) 12/15
Strong rope or cable
fixed to antenna steelmount to avoid
collision with the towerstructure during
hoisting
Strong rope fixed at the tower top.
The rope is slipping through a steel roll ora shackle, wich is fixed on the steel mountof the antenna (to avoid any turnings ofthe antenna e.g. due to wind)
To winch
-
8/13/2019 8ft Antenna (HTT81.221-10)
13/15
HTT 81.221-10 (e) 13/15
16. Antenna installation on tower pipe(lifting accessories are not shown)
17. Sway bar positionning
4 washers 158 nuts M14
2 U-bolts M14(Do not forget to apply antiseize installation paste on
U-bolt threads)
U-bolt M14(Do not forget to apply anti seize
installation paste on U-bolt
2 washers 154 nuts M14
Max25
- Angle the sway bar- Install the pre-assembled fine adjustment azimuth spindle on the
sway bar pipe
- Choose the optimal place on the tower, to fix the fine adjustmentazimuth spindle system (respect the 25 sway bar orientation)
- After sway bar positionning, do not torque tighten nuts until elevation& azimuth adjustment.
Adjust nut and bolts tightening to have a freerotation & orientation in any direction withoutgap between parts
-
8/13/2019 8ft Antenna (HTT81.221-10)
14/15
HTT 81.221-10 (e) 14/15
Loosen or tightenthe M16 brassnuts to adjustElevation
The fine adjustmentAzimuth spindle systemmust have been loosen
If the bolts are torquetighten, loosen of turnthe M20 nut of the right &left pivots
18. Elevation adjustment
After Elevation fine adjustment, lock each M20 nuts on the pivots at the specific torque
value specified on the torque table joined(the threads must have been greased beforetorque tightening). Then torque tighten the M16 brass nuts of the Elevation spindle.
-
8/13/2019 8ft Antenna (HTT81.221-10)
15/15
HTT 81.221-10 (e) 15/15
If the nuts of the bottom U-bolt are torquetighten, loosen of turn the M14 nuts
If the nuts of the
2 upper U-boltsare torquetighten, loosen of turn the M14nuts
(Do not loosen theU-Bolt of the Angle
Safety Support)
Loosen or tightenthis M20 nuts toadjust Azimuth
This U-Bolt M12 must betorque tighten
This 2 nuts M20 must be tighten
This 2 U-bolts M12 must behandtighten
This bolt mustbe torque
tighten
This boltmust be
handtighten
duringadjustment
19. Azimuth adjustment
20. Final Check
After azimuth adjustment, lock each first nut on the M14 U-bolts at the specifictorque value specified on the torque table joined (the U-bolt threads must have beengreased before torque tightening), then tighten the second nut against the first oneusing usual wrench (Do not use 2 wrenches to fix the second nut). Then torquetighten all the nuts and bolts of the Azimuth spindle.
When the installation of the antenna has been completed, it is necessary to makesure that the installation instructions have been followed in all aspects.It is especially important to check that all bolted joints are torque tightly
locked.
Check that is freein rotation &orientation in anydirection withoutgap betweenparts.