8.3 Stack Organization Stack: A storage device that stores
information in such a manner that the item stored last is the first item retrieved.
Also called last-in first-out (LIFO) list. Useful for compound arithmetic operations and nested subroutine calls.
8.3 Stack Organization • Stack pointer (SP): A register that
holds the address of the top item in the stack. SP always points at the top item in the stack
• Push: Operation to insert an item into the stack.• Pop: Operation to retrieve an item from the stack.
REGISTER STACK
• A stack can be organized as a collection of a finite number of registers.
• In a 64-word stack, the stack pointer contains 6 bits.• The one-bit register FULL is set to 1 when the stack is full; EMPTY register is 1 when the stack is empty.• The data register DR holds the data to be written into or read from the stack.
REGISTER STACK
InitializationSP 0, EMPTY 1, FULL 0PushSP SP + 1M[SP] DRIf (SP = 0) then (FULL 1) Note that SP becomes 0 after 63EMPTY 0
The following are the micro-operations associated with the stack
DR M[SP]SP SP - 1If (SP = 0) then (EMPTY 1)FULL 0
Pop
The following are the micro-operations associated with the stack
STACK OPERATIONSREVERSE POLISH NOTATION (postfix)
Reverse polish notation :is a postfix notation (places operators after operands)
(Example) Infix notation A + BReverse Polish notation AB+ also called postfix.
STACK OPERATIONSREVERSE POLISH NOTATION (postfix)
A stack organization is very effective for evaluating arithmetic expressions
A * B + C * D (AB *)+(CD *) AB * CD * +
( 3 * 4 ) + ( 5 * 6 ) 34 * 56 * +
STACK OPERATIONSREVERSE POLISH NOTATION (postfix)
n • Evaluation procedure:
n 1. Scan the expression from left to right.2. When an operator is reached, perform the operation with the two operands found on the left side of the operator.3. Replace the two operands and the operator by the result obtained from the operation.
n (Example) infix 3 * 4 + 5 * 6 = 42 postfix 3 4 * 5 6 * +
n 12 5 6 * +12 30 +42
STACK OPERATIONSREVERSE POLISH NOTATION (postfix)
• Reverse Polish notation evaluation with a stack. Stack is the most efficient way for evaluating arithmetic expressions.
stack evaluation:Get valueIf value is data: push dataElse if value is operation: pop, pop evaluate and push.
STACK OPERATIONSREVERSE POLISH NOTATION (postfix)
(Example) using stacks to do this. 3 * 4 + 5 * 6 = 42
=> 3 4 * 5 6 * +
• The most common fields in instruction formats are:1. Mode field: Specifies the way the effective address is determined 2. Operation code: Specifies the operations to be performed.3. Address field: Designates a memory address or a processor
register
Mode Opcode Address
8.4 Instruction Formats
8.4 Instruction Formats• Zero address instruction: Stack is used. Arithmetic
operation pops two operands from the stack and pushes the result.
• One address instructions: AC and memory. Since the accumulator always provides one operand, only one memory address needs to be specified.
•Two address instructions: Two address registers or two memory locations are specified, one for the final result.
•Three address instructions: Three address registers or memory locations are specified, one for the final result.
It is also called general address organization.
Zero address instructions
Instruction: ADDPush and pop operations need to specify one address involved in data transfer.
Instruction: POP XEvaluate X = ( A + B ) * ( C + D )
Stack-organized computer does not use an address field for the instructions ADD, and MUL
PUSH, and POP instructions need an address field to specify the operand
Zero address instructions
PUSH A
PUSH B
ADD
PUSH C
PUSH D
ADD
MUL
POP X TOSX
BADCTOS
DCTOS
DTOS
CTOS
BATOS
BTOS
ATOS
)()(
)(
)(
Advantages: No memory addresses needed during the operation.Disadvantages: results in longer program codes.
One address instructions One address can be a register name or
memory address. SINGLE ACCUMULATOR ORGANIZATION
Since the accumulator always provides one operands, only one memory address needs to be specified.Instruction: ADD XMicrooperation: AC AC + M[X]
One address instructions
LOAD A
ADD B
STORE T ACTM
BMACAC
AMAC
][
][
][
All operations are done between the AC register and memory operand
Advantages: fewer bits are needed to specify the address.Disadvantages: results in writing long programs.
Two address instructions • Assumes that the destination
address is the same as that of the first operand. Can be a memory address or a register name.
Instruction: ADD R1, R2Microoperation: R1 R1 + R2
Two address instructions
MOV R1, A
MOV R2, B
ADD R1, R2
MOV X, R1 1][
211
][2
][1
RxM
RRR
BMR
AMR
most common in commercial computers
Each address fields specify either a processor register or a memory operand
Advantages: results in writing medium size programsDisadvantages: more bits are needed to specify two addresses.
Three address organization
GENERAL REGISTER ORGANIZATION
• Three address instructions: Memory addresses for the two operands and one destination need to be specified.Instruction: ADD R1, R2, R3Microoperation: R1 R2 + R3
Advantages: results in writing short programsDisadvantages: more bits are needed to specify three addresses.
ADD R1, R2, R3 321 RRR
EXAMPLE: Show how can the following operation be performed using:a- three address instructionb- two address instructionc- one address instructiond- zero address instructionX = (A + B) * (C + D)
a-Three-address instructions (general register organization)
• ADD R1, A, B
• R1 M[A] + M[B]
• ADD R2, C, D
• R2 M[C] + M[D]
• MUL X, R1, R2
• M[X] R1 * R2
b-Two-address instructions (general register organization)
• MOV R1, A • R1 M[A]• ADD R1, B • R1 R1 + M[B] • MOV R2, C • R2 M[C]• ADD R2, D • R2 R2 + M[D]• MOV X, R2 • M[X] R2 • MUL X, R1 • M[X] R1 * M[X]
c- One-address instructions
• LOAD A • AC M[A] • ADD B • AC AC + M[B] • STORE T • M[T ] AC • LOAD C• AC M[C]• ADD D • AC AC + M[D]• MUL T • AC AC * M[T ] • STORE X • M[X] AC Store
d- Zero-address instructions (stack organization)
• Push value • Else If operator is encountered: Pop, pop, operation,
push• Pop operand pop another operand then perform an
operation and push the result back into the stack.
• PUSH A TOS A Push• PUSH B TOS B• ADD TOS (A+B)• PUSH C TOS C• PUSH D TOS D• ADD TOS (C+D)• MUL TOS (C+D)*(A+B)• POP X M[X] TOS• (*TOS stands for top of stack).
Pop, pop, operation, push