GROUP NUMBER
(8) HYU n a R 11 nEW THlnKlnG. nEW POSSIBILITIES. BODY ELECTRICAL 13-BE-007
Technical Service Bulletin DATE MODEL(S)
AUGUST 2013 EQUUS (VI)
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
Description: This bulletin describes the procedure for the programming/teaching and operation of Equus Smart Key Cards and Conventional Smart Keys .
*NOTE
Once the 1st key is programmed, the customer's 2nd and 3rd keys must be programmed at the same time or they will not start the vehicle.
*NOTE
Before attempting the key programming procedure, call Techline to obtain the 6 digit PIC pin code. Techline phone number: 800-325-6604.
!Applicable Vehicles: 2014MY Equus (VI) 5.0L
Warranty Information: Normal warranty applies .
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors , Technicians , Body Shop Manager, Fleet Repair
SUBJECT: 2014 EQUUS SMART KEY/CARD PROGRAMMING & OPERATION
Main Features:
Conventional Smart Key Card Type Smart Key
4 3 2
Function Keys
* 4 Buttons * No button
Mechanical Key
* Press and hold the release button * Push and hold the release lever
3
Battery 2
* Battery Specification : CR2032 * Battery Specification : CR2412
I* NOTE I ~----ii 11--~~~~~~~~~~~~~~~~~~~~~~~-,
Up to 3 Smart Keys (including card type Smart Keys) can be registered to the vehicle . They can be a combination of 2 Conventional Smart Keys and 1 Smart Key Card, or 2 Smart Key Cards and 1 Conventional Smart Key.
TSB #: 13-BE-007 Page 2 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
Functions:
Function Action Conventional Card Type
Smart Key Smart Key
Press the door handle button • • To Lock Door Press the Door Lock button • x
on the smart key Door
Put your hand on the driver's outside • • To door handle Unlock Door Press the Door Unlock button • x
on the Smart Key
Press the Trunk Unlock button on the • x smart key for more than one second
Press the trunk release button on the • • To trunk lid Open Trunk
Trunk Use the mechanical key • • Press the TRUNK button or power trunk main control button under the steering • • wheel
To Lower the trunk lid and press down
Close • • Trunk until it locks
Engine Press the engine start button • • Button Start with the key inside the vehicle Engine Start Engine Press the engine start button
Stop while the engine is running • • Panic - Press the PANIC button on the smart key • x
TSB #: 13-BE-007 Page 3 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
Smart Key Card/Conventional Smart Key Programming Procedure:
*NOTE
Before proceeding, have all 3 Smart Keys ready and the 6 digit PIC pin code obtained from Techline. Techline phone number: 800-325-6604.
1. Connect the DLC cable of the VCI to the data link connector located under the left side of dash.
2. From the System Screen , select "PIC" and click "OK"
TSB # : 13-BE-007
; "t¥t: 0 •• " H ! " • -=-~
!i<M>IG>l4JH9EU074998 ::J
I ,
Select System Selected System
Fault Code Searching
Page 4 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
3. Click the "Vehicle S/W Management" tab. Select "Option Treatment" and then click "Smart Key Code Saving".
4 . Turn the ignition OFF and press "OK" on the GOS.
5. Enter the 6 digit PIC pin code obtained from Techline and click "OK".
TSB # : 13-BE-007
Smart KcyCo4c ~II
Pr•i>-,.tJon
..l System Identification
..> Neutralization Mode
-' SMK STATUS INFORMATION
J FOB KEY STATUS INFORMATION
...> Sm.act Key Code Saving
\ol Current FOB Key Ch~k
\,) Serial Communication Line Ch~ck
Antenna St.JIUS Check
[ Smal'! Key Code SllYlngJ
rcondlllon J
1 10011'
Ptease havt!F08kll)'lotncnindpr11s1fOKl but:on
lnpul PIN code and P!BS!I IOKl IHJ!lon
Page 5 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
6. Have all 3 Smart Keys ready and click "OK".
7. Click "OK" and within 5 seconds use the first Smart Key to press and hold the Start Stop button. Keep the button pressed in fully for one or two seconds , then release .
[ Smart Key Code Saving J
1st key teaching
Click [OK[, and then press SSB(Start Stop Button)
using 1st FOB w ithin 5 seconds.
(Do not use youninger to press SSB, but use FOB itse lf)
Continue? (OK/CANCEL)
*NOTE
Do not use your finger to press the Stop Start button. Use the Smart Key or Key Card to fully press the button as shown.
When teaching the Smart Key Card , use the upper left corner of the card to press the Start Stop button. It may be marked with red tape.
TSB #: 13-BE-007
SmartKQytolilo5aVl:ng - -- - - - ..,.,, - -- - - - [Qt-
[Smart Key Code Sw.ing I
1sl key teachlng
Ciiek [OKI. and men 111es'i sse(Start Stop Bur.on)
using tst FOBwlthln5 setonds
{DOnolU'iEIYourfrngerropressSSB,tlutuseFOBttsetr)
Conllnue? (OKICANCEL)
Page 6 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
8. After successfully teaching the 1 st key, this screen will appear. Click "OK" and proceed to teach the 2 nd key.
9. When the 2 nd key teaching is complete , press "OK" and teach the 3 rd and final key.
10. After successfully teaching the 3rd key, this screen will appear. Click "OK".
TSB #: 13-BE-007
5mlUIKtyCodo51!1Wlg - -- -
JSmartKeyCOde Sa¥1ng]
1stkE"t'teathtngcompletedl
Clkk IOIQ, and tnen pren SSB(Slirt 5'.op Buton)
usJng2ndFOB W1ttun ~ seconc1s.
(Oo not useyournnge11opressSSB,but useF09Hsell)
Contmur? (OKIC>.NCElJ
1smar1 KevCodeSarlng ]
2ndf.vyteilctl!ngccmpletedl
Click 101(). and lh11n press SSB(St.lrt Slop Bllilon)
usmg3rd FOBWlthln5HtoniJs
(Oon01useyou1Mgertop1euSS El,but use FOSlt$ell)
conunue?(OIQCANCEW
liiil ml
Page 7 of 8
SUBJECT: 2014 EQUUS SMART KEY /CARD PROGRAMMING & OPERATION
11 . A screen showing that the Smart Key teaching has been completed will open and will display that 3 Smart Keys have been taught. Click "OK".
12. Confirm operation of all Conventional Smart Keys and Smart Key Cards.
If Smart Keys are inoperative, refer to Steps 3-11 to repeat the procedure.
TSB #: 13-BE-007
Smart Key Cod• S1Mn11 - - - -
I Smart Key Colle S;r,ino I
Smart Kevt&athlng completed!
Number 0fl1ugh!F09ktys : 3
Iii)
Page 8 of 8