1
60M,59K,67L,76G,83K,82C-74E
TABLE OF CONTENTS 1FUEL RECOMMENDATION
2BEFORE DRIVING
3OPERATING YOUR VEHICLE
4DRIVING TIPS
5OTHER CONTROLS AND EQUIPMENT
6VEHICLE LOADING AND TOWING
7INSPECTION AND MAINTENANCE
8EMERGENCY SERVICE
9APPEARANCE CARE
10GENERAL INFORMATION
11SPECIFICATION
2
60M,59K,67L,76G,83K,82C-74E
3
60M,59K,67L,76G,83K,82C-74E
FOREWORDAll information in this manual is basedon the latest product informationavailable at the time of publication.Due to improvements or otherchanges, there may be discrepanciesbetween information in this manualand your vehicle. MARUTI SUZUKIINDIA LIMITED reserves the right tomake production changes at any time,without notice and without incurringany obligation to make the same orsimilar changes to vehicles previouslybuilt or sold. This vehicle may notcomply with standards or regulationsof other countries. Before attemptingto register this vehicle in any othercountry, check all applicableregulations and make any necessarymodifications.
0-1
This manual is an essential part of yourvehicle and should remain with the vehiclewhen resold or otherwise transferred to anew owner or operator. Please read thismanual carefully before operating your newMARUTI SUZUKI and review the manualfrom time to time. It contains importantinformation on safety, operation andmaintenance. You are invited to avail thethree Free Inspection Services as describedin the manual. Three free inspectioncoupons are attached to this manual. Pleaseshow this manual to yourdealer while you take your MARUTI SUZUKIfor any Service.To prolong the life of your vehicle andreduce maintenance cost, the periodicmaintenance must be carried out accordingto “PERIODIC MAINTENANCE SCHEDULE”described in “INSPECTION ANDMAINTENANCE” section of this manual. Itis essential for preventing trouble andaccidents to ensure your satisfaction andsafety. Daily inspection and care as per“DAILY INSPECTION CHECKLIST”described in the “INSPECTION ANDMAINTENANCE” section of this manual isessential for prolonging the life of thevehicle and for safedriving.
MARUTI SUZUKI INDIA LIMITED
MARUTI SUZUKI INDIA LIMITED believesin conservation and protection of Earth’snatural resources. To that end, weencourage every vehicle owner to recycle,trade-in or properly dispose of, asappropriate, used Engine Oil, coolant andother fluids, batteries and tyres etc.
4
60M,59K,67L,76G,83K,82C-74E
MODIFICATION WARNINGwwwww WARNING
Do not modify your vehicle.Modification could adversely affectsafety, handling, performance, ordurability and may violategovernmental regulations. In addition,damage or performance problemsresulting from modification may notbe covered under warranty.
0-2
tttttWARNING/ tttttCAUTION/ NOTICE/NOTEPlease read this manual and follow itsinstructions carefully. To emphasize specialinformation, the symbol and the wordsWARNING, CAUTION, NOTICE and NOTEhave special meanings. Pay particularattention to messages highlighted by thesesignal words:
IMPORTANT
wwwww WARNINGIndicates a potential hazard that couldresult in death or serious injury.
Indicates a potential hazard that couldresult in minor or moderate injury.
ttttt CAUTION
NOTICEIndicates a potential hazard that couldresult in vehicle damage.
NOTE:Indicates special information to makemaintenance easier or instructions clearer.
76G-00-001
The circle with a slash in this manualmeans “Don’t do this” or “Don’t let thishappen”.
NOTICEImproper installation of mobilecommunication equipment such ascellular telephones or CB (Citizen’sBand) radios may cause electronicinterference with your vehicle’signition system, resulting in vehicleperformance problems. Consult yourMARUTI SUZUKI dealer for advice oninstalling such mobile communi-cationequipment.
wwwww WARNINGSevere damage may be caused by theuse of either poor quality fuel and/orlubricants not recommended byMARUTI SUZUKI.
5
60M,59K,67L,76G,83K,844-74E
1MAINTENANCE SERVICE RECORD
IMPORTANT INFORMATION TO CUSTOMER
Dear CustomerFor any assistance with regard to our product, please contactGeneral Manager/Works Manager at any of our Dealer orAuthorised Service Station. For additional enquiry you maycontact our Regional office or Service Division. TheAddresses and Phone nos. are given in Service Networkbooklet provided along with vehicle.
MODEL CHASSIS NO. ENGINE NO. KEY NO. DATE OF MILEAGE BATTERY DELIVERY (km) MAKE SR. NO./BATCH CODE
OWNER’S NAME & ADDRESS ____________________________________________________________________________
_____________________________________________________________________ TEL. NO. _________________________
ADDRESS/STAMP OF SELLING DEALER SELLING DEALER CODE
SHOWROOM
WORKSHOP
MAINTENANCE SERVICE RECORD
0-3
6
60M,59K,67L,76G,83K,844-74E
F....free Service P....Paid Service W....Warranty. A....Accident
MAINTENANCE SERVICE RECORD
DATE OF KIND OF MILEAGE DESCRIPTION OF JOB NAME OF SERVICING JOB CARD MECHANIC’SSERVICE SERVICE (km) DEALER/MASS NO. SIGNATURE
0-4
7
60M,59K,67L,76G,83K,844-74E WARRANTY POLICY
0-5
WARRANTY POLICYMaruti Suzuki India Limited (hereinafter called "Maruti Suzuki"),warrants that each new Maruti Suzuki vehicle distributed in Indiaby Maruti Suzuki and sold by an authorised Maruti Suzuki dealerwill be free, under normal use and service, from any defects inmaterial and workmanship at the time of manufacture SUBJECTTO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty:
(a) The Maruti Suzuki vehicle must be delivered by MarutiSuzuki authorised dealer and set-up, serviced by MarutiSuzuki authorised dealer/service station.
(b) The warranty registration card in respect of each vehiclemust be completed by the dealer at the time of deliveryof the vehicle and dealer should retain the same.
(2) Term:The term of the warranty shall be twenty four (24) monthsor 40,000 kilometers (whichever occurs first) from the dateof delivery to the first owner.
(3) Maruti Suzuki's Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehiclewithin the term stipulated above, Maruti Suzuki's only obligationis to repair or replace at its sole discretion any part shownto be defec-tive, with a new part or the equivalent at no costto the owner for parts or labour, when Maruti Suzukiacknowledges that such a defect is attributable to faultymaterial or workmanship at the time of manufacture. Theowner is responsible for any repair or replacements which are
not covered by this warranty.(4) Limitation:
This warranty shall not apply to:(1) normal maintenance service required other than the three
free services, including without limitation, oil and fluidchanges, headlight aiming, fastener retightening, wheel bal-ancing, wheel alignment and tyre rotation, cleaning ofinjectors, adjustments of carburettor, ignition timing, clutchand valve clearance.
(2) the replacement of normal wear parts including withoutlimitation, bulbs, tyres and tubes, spark plugs, belts,hoses, filters, wiper blades, brushes, contact points, fuses,clutch disc, brake shoes, brake pads, cable and all rubberparts (except oil seal and glass run).
(3) any vehicle which has been used for competition or racing.(4) any repairs or replacement required as a result of
accidents or collision.(5) any defects caused by misuse, negligence, abnormal use
or insufficient care.(6) any vehicle which has been modified or altered, including
without limitation, the installation of performance accessories.(7) any vehicle on which parts or accessories not approved
by Maruti Suzuki have been used.(8) any vehicle which has not been operated in accordance
with the operating instructions in the Maruti SuzukiOwner’s Manual.
(9) any vehicle which has not received, during the warrantyterm, the service inspections prescribed in the MarutiSuzuki Owner’s Manual.
(10) any vehicle which has been assembled, disassembled,adjusted or repaired by other than an Maruti Suzukiauthorised dealer/service station.
8
60M,59K,67L,76G,83K,844-74EWARRANTY POLICY
0-6
(11) any vehicle which has been used for purposes other thanwhat it was designed for.
(12) any damage or deterioration caused by industrial pollutionand bird droppings.
(13) insignificant defects which do not affect the function ofthe vehicle including without limitation, sound, vibrationand fluid seep.
(14) any natural wear and tear including without limitation,aging etc.
(15) Installation and usage of Domestic LPG Gas/LPG cylinder.(16) V-belts, hoses and gas leaks (For Maruti Suzuki AC
vehicle).(17) Any vehicle retrofitted with LPG / CNG kits.
(5) Extent of Warranty:This warranty is the entire written warranty given by MarutiSuzuki for Maruti Suzuki vehicles and no dealer or its or hisagent or employee is authorised to extend or enlarge thiswarranty and no dealer or its or his agent or employee isauthorised to make any oral warranty on Maruti Suzuki'sbehalf.Maruti Suzuki reserves the right to add any improvements orchange the design of any model at any time with no obligationto make the same changes on units previously sold.
(6) Warranty Service:To obtain warranty service, the complete vehicle must bepresented at the owner’s expenses to any authorised MarutiSuzuki dealer.
(7) Owner’s Warranty Responsibilities:It is responsibility of each owner to:
(a) make certain that the warranty registration/PDI card wascompleted at the time of delivery of the vehicle;
(b) have performed, at his own expenses, by an MarutiSuzuki authorised dealer/service station all the serviceinspections specified in the Maruti Suzuki “Owner’s Manualand Service Booklet” and maintain adequate proof thatsuch service inspections have been performed.
(c) make certain that the Maruti Suzuki authorised dealer/servise station performing the service inspection hascertified the work on the “Maintenance Service Record”page in the “Owner’s Manual and Service Booklet” and
(d) present the Maruti Suzuki “Owner’s Manual and ServiceBooklet” to the authorised Maruti Suzuki dealer wheneverrequesting service inspections or warranty service.
If the “Owner’s Manual and Service Booklet” should be lostor destroyed the owner should consult the authorised MarutiSuzuki dealer from whom the vehicle was purchased forinstructions concerning replacement of the “Owner’s Manualand Service Booklet”.
(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle,loss of time, inconvenience or any other indirect incidentalor consequential damage resulting from the vehicle not beingavailable to the owner because of any defect covered by thiswarranty.
(9) Change of OwnerEven if ownership of the vehicle changes, the remainingwarranty period is effective for the new owner.
9
60M,59K,67L,76G,83K,844-74E
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles (apart from the Regular warranty and will run parallelto the regular product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect fromJuly 1st, 2001.
Terms:
The Emission Warranty will be applicable for 80,000 kms or 3 years (Which ever comes earlier) from the date of delivery tothe first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of allvalid document.
Conditions:
1. Under Emission Warranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet to theEmission Standard as specified in sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examination carried out by Maruti Suzuki or it's dealer which leads to firm conclusionsthat the
a) Original settings have not been tempered in any case.
b) Part (as given in Annexure-A) has a manufacturing defect.
c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and usedin accordance with the instructions as specified in Owner's Manual and Service Booklet and the used fuel and different oils(Engine oil, Transmission oil, Brake oil etc.) are also as per specification.
3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti Suzuki and it's dealerand results of the examination will be final and binding. If after examination, the warrantable condition is not established, MarutiSuzuki and it's dealer has the right to charge all, or part of the cost of such examination.
4. Under Emission Warranty, the parts (as given in Annexure-A) will be changed free of cost, but the consumables will be chargedas per actual.
5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these beingintegral parts a complete assembly, Maruti Suzuki and it's dealer will have the sole discretion to replace entire assembly or byusing some of the parts of the system through suitable repair or modifications.
EMISSION WARRANTY
0-7
EMISSION WARRANTY
10
60M,59K,67L,76G,83K,844-74E
6. Any consequential repairs or replacement of parts which may be found necessary to establish compliance of Emission Warranty,will not be considered under warranty, unless the same is under product warranty. The consumable will be charged as per actualunder such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transportation of the vehicle to the nearest Maruti Suzuki dealer workshopor any loss due to non-availability of the vehicle during the period of lodging of a warranty claim and examination and/or repairby Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that may be charged by statutory authorities on account of failure to complywith the EMISSION STANDARDS.
9. Emission Warranty will not be affected on the change of owner, provided all the documents are available.
10. All maintenance actions (as specified in the Owner's Manual and Service Booklet) need to be followed and recorded in the manualfor emission warranty.
11. The customer needs to produce the PUC (Pollution Under Control) certificate valid for the period preceding the test during whichthe failure is discovered. The receipts (for the maintenance of the vehicle as per specification in Owner's Manual and ServiceBooklet from the date of original purchase of the vehicle) will also be required.
Condition Under which the Emission Warranty is not APPLICABLE
1. In the absence of valid PUC certificate.
2. Vehicle not serviced from Maruti Suzuki authorised workshop as per the schedule specified in the Owner's Manual.
3. Vehicle subjected to abnormal use (accident, motor race, rallies or for the purpose of establishing the records etc.)
4. Use of non MGP (Maruti Genuine Part).
5. Vehicle tempered in an unauthorised manner.
6. Tampering with odometer so that the actual kilometer reading can not be read.
7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmission oil and Brake oil etc.)
EMISSION WARRANTY
0-8
11
60M,59K,67L,76G,83K,844-74E
Annexure-A
List of parts covered under Emission Warranty
1. Fuel injection Assembly, Pressure Regulator, Throttle Body Assembly.
2. Electronic Control Module (ECM).
3. Intake Manifold.
4. EGR valve.
5. Distributor and internal parts.
6. Ignitions coil.
7. Canister Assembly.
8. Vapour Liquid Separator.
9. Fuel Tank and Filler Cap.
10. PCV (Positive Crankcase Ventilation) Valve.
11. Oil Filler Cap.
12. Catalytic Convertor.
13. Exhaust manifold.
14. All fuel injection System related SENSORS.
15. High Pressure Fuel Pump.
16. Glow Plug.
17. Glow Plug Controller.
18. Maniverter
EMISSION WARRANTY
0-9
12
60M,59K,67L,76G,83K,844-74E
MEMO
13
76G-74E BEFORE DRIVING
FUEL RECOMMENDATIONFuel Recommendation ....................................................................................................... 1-1
1
14
76G-74E
1-1
BEFORE DRIVING
Fuel Recommendation
Petrol EngineYou must use unleaded Petrol with anoctane number (RON) of 91 or higher.
Petrol/Ethanol blendsBlends of unleaded Petrol and ethanol(grain alcohol), also known as gasohol, arecommercially available in some areas.Blends of this type may be used in yourvehicle if they are no more than 10% etha-nol. Make sure this Petrol-ethanol blend hasoctane ratings no lower than thoserecommended for Petrol.
Petrol/Methanol blendsBlends of unleaded Petrol and methanol(wood alcohol) are also commercially availablein some areas. DO NOT USE fuels containingmore than 5% methanol under anycircumstances. Fuel system damage orvehicle performance problems resulting fromthe use of such fuels are not the responsibilityof MARUTI SUZUKI and may not be coveredunder the New Vehicle Warranty.Fuels containing 5% or less methanol maybe suitable for use in your vehicle if theycontain cosolvents and corrosion inhibitors.
NOTE:If you are not satisfied with the driveabilityor fuel economy of your vehicle when you
are using a Petrol/alcohol blend, you shouldswitch back to unleaded Petrol containingno alcohol.
The fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuelafter the filler nozzle has automaticallyshut off or an initial blowback occurs,the air chamber will become full.Exposure to heat when fully fuelled inthis manner will result in leakage dueto fuel expansion. To prevent suchfuel leakage, stop filling after the fillernozzle has automatically shut off, orwhen using an alternative non-automatic system, initial ventblowback occurs.
NOTICE
Be careful not to spill fuel containingalcohol while refueling. If fuel isspilled on the vehicle body, wipe it upimmediately. Fuels containing alcoholcan cause paint damage, which is notcovered under the New VehicleLimited Warranty.
NOTICE
Number (CN) higher than 51 and sulfurcontent less than 350 ppm (parts per mil-lion). MARUTI SUZUKI recommends to usethe diesel fuel conformable to EN590. Donot use marine diesel fuel, heating oils andso forth.
Diesel EngineThe diesel fuel should be with Cetane
NOTICEThe fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuelafter the filler nozzle has automaticallyshut off or an initial blowback occurs,the air chamber will become full.Exposure to heat when fully fuelled inthis manner will result in leakage dueto fuel expansion. To prevent suchfuel leakage, stop filling after the fillernozzle has automatically shut off, orwhen using an alternative non-automatic system, initial ventblowback occurs.
Be careful not to spill fuel containingalcohol while refueling. If fuel isspilled on the vehicle body, wipe it upimmediately. Fuels containing alcoholcan cause paint damage, which is notcovered under the New VehicleLimited Warranty.
NOTICE
15
76G-74E BEFORE DRIVING
BEFORE DRIVINGKeys ...................................................................................................................................... 2-1Door Locks .......................................................................................................................... 2-2Keyless Entry System Transmitter (if equipped) ......................................................... 2-4Security System (if equipped) ......................................................................................... 2-6Windows ............................................................................................................................... 2-6Mirrors .................................................................................................................................. 2-7Front Seats .......................................................................................................................... 2-8Rear Seats ......................................................................................................................... 2-10Seat Belts and Child Restraint Systems ..................................................................... 2-14Supplemental Restraint System (air bags) (if equipped) ......................................... 2-22Instrument Cluster ............................................................................................................ 2-27Warning and Indicator Lights ........................................................................................ 2-28Speedometer ...................................................................................................................... 2-32Tachometer (if equipped) ................................................................................................ 2-32Fuel Gauge ........................................................................................................................ 2-33Temperature Gauge .......................................................................................................... 2-33Brightness Control ........................................................................................................... 2-33Information Display .......................................................................................................... 2-34Lighting Control Lever .................................................................................................... 2-38Front Fog Light Switch (if equipped) .......................................................................... 2-38Headlight Leveling Switch .............................................................................................. 2-39Turn Signal Control Lever .............................................................................................. 2-39Hazard Warning Switch ................................................................................................... 2-40Windshield Wiper .............................................................................................................. 2-40Washer Lever .................................................................................................................... 2-41Tilt Steering Lock Lever ................................................................................................. 2-41Horn ..................................................................................................................................... 2-42Heated Rear Window Switch (if equipped) ................................................................. 2-42
2
16
76G-74E
Keys
Your vehicle comes with a pair of identicalkeys. Keep the spare key in a safe place.One key can open all of the locks on thevehicle.
The key identification number is stamped ona metal tag provided with the keys or onthe keys. Keep the tag (if equipped) in asafe place. If you lose your keys, you willneed this number to have new keys made.Write the number below for your future ref-erence.
KEY NUMBER:
which has an electronic identification codeprogrammed into it. The key communicatesthe identification code to the vehicle whenthe ignition switch is turned to the “ON”position. If you need to make spare keys,see your MARUTI SUZUKI dealer. Thevehicle must be programmed with the correctidentification code for the spare keys. A keymade by an ordinary locksmith will not work.
60M-02-002
If the immobilizer system light blinks whenthe ignition switch is in the “ON” position,the engine will not start.
NOTE:• If this light blinks, turn the ignition switch
to the “LOCK” position, then turn it backto the “ON” position.
• If the light still blinks with the ignition switchturned to the “ON” position, there may besomething wrong with your key or with theimmobilizer system. Ask your MARUTISUZUKI dealer to inspect the system.
NOTE:• If you lose your immobilizer ignition key,
see your MARUTI SUZUKI dealer assoon as possible to have the lost onedeactivated, then have the new keymade by them.
• If you own other vehicles with immobi-lizer keys, keep those keys away fromthe ignition switch when using yourMARUTI SUZUKI, or the engine may notbe started because they may interferewith your MARUTI SUZUKI immobilizersystem.
• If you attach any metal objects to theimmobilizer key, it may not start theengine.
NOTICEThe immobilizer key is a sensitiveelectronic instrument. To avoid dam-aging the immobilizer key:• Do not expose it to impacts, mois-
ture or high temperature such as onthe dashboard under direct sunlight.
• Keep the immobilizer key away frommagnetic objects.
Ignition Key ReminderA buzzer sounds intermittently to remindyou to remove the ignition key if it is in theignition switch when the driver’s door isopened.
2-1
BEFORE DRIVING
60M-02-001
Immobilizer SystemThis system is designed to help preventvehicle theft by electronically disabling theengine starting system.The engine can be started only with yourvehicle’s original immobilizer ignition key
17
76G-74E
Door LocksSide Door Locks
1) UNLOCK2) LOCK3) Front4) Rear
To lock a front door from outside the vehi-cle:
• Insert the key and turn the top of thekey toward the front of the vehicle, or
• Turn the lock knob forward, then pulland hold the door handle as you closethe door.
To unlock a front door from outside thevehicle, insert the key and turn the top ofthe key toward the rear of the vehicle.
60M-02-003
60M-02-004
1) LOCK2) UNLOCK
To lock a door from inside the vehicle, turnthe lock knob forward. Turn the lock knobrearward to unlock the door.
To lock a rear door from outside the vehi-cle, turn the lock knob forward and closethe door. You do not need to pull and holdthe door handle as you close the door.
NOTE:Be sure to hold the door handle when youclose a locked front door, or the door willnot remain locked.
Central Door Locking System(if equipped)
1) UNLOCK2) LOCK3) Front4) Rear
You can lock and unlock all doors (includ-ing the tailgate) simultaneously by using thekey in the driver’s door lock.
To lock all doors simultaneously, insert thekey in the driver’s door lock and turn thetop of the key toward the front of thevehicle.
To unlock all doors simultaneously, insertthe key in the driver’s door lock and turnthe top of the key toward the rear of thevehicle.
60M-02-005
EXAMPLE
2-2
BEFORE DRIVING
18
76G-74E
60M-02-006
1) LOCK2) UNLOCK
You can also lock or unlock all doors bydepressing the front or rear of the switch,respectively.
NOTE:• If your vehicle is equipped with the
keyless entry system, you can also lockor unlock all doors by operating thetransmitter. Refer to “Keyless EntrySystem Transmitter” in this section.
NOTE:• If your vehicle is equipped with security
system, all doors are automaticallyunlocked when your turn the ignitionswitch to the “LOCK” position and pullout the key.
• All doors are automatically closed forsafety when the vehicle speed reaches20 km/h.
Child-Proof Locks (rear door)
1) LOCK2) UNLOCK
Each of the rear doors is equipped with achild-proof lock which can be used to helpprevent unwanted opening of the door frominside the vehicle. When the lock lever is inthe “LOCK” position (1), the rear door canonly be opened from outside. When the locklever is in the “UNLOCK” position (2), the reardoor can be opened from inside or outside.
60M-02-007
wwwww WARNINGBe sure to place the child-proof lockin the “LOCK” position wheneverchildren are seated in the rear.
Tailgate
Always make sure that the tailgate isclosed and latched securely. Com-pletely closing the tailgate helps pre-vent occupants from being thrownfrom the vehicle in the event of anaccident. Completely closing it alsohelps keep exhaust gases from enter-ing the vehicle.
wwwww WARNING
Type 1
You can lock and unlock the tailgate byusing the key in the driver’s door lock.To open the tailgate, pull up and hold thetailgate handle (1) and lift the tailgate.If you cannot unlatch the tailgate by pullingup the tailgate handle (1) due to a dis-
60M-02-008
2-3
BEFORE DRIVING
EXAMPLE
19
76G-74E
charged battery or malfunction, follow theprocedures below to unlatch the tailgatefrom inside the vehicle.1) Fold the 3rd row seat forward for easier
access. Refer to “Folding Rear Seats”section for details on how to fold the 3rdrow seat forward.
60M-02-009
2) Push open the tailgate from inside bypushing up on the emergency lever (2)using a flat blade screwdriver or the jackhandle. The tailgate will be latched againby closing the tailgate simply.
If the tailgate cannot be unlatched by pull-ing up the tailgate handle (1), have thevehicle inspected by your MARUTI SUZUKIdealer.
wwwww CAUTION• To avoid injury, do not use your fin-
ger to push the emergency lever.• Make sure there is no one near the
tailgate when pushing open the tail-gate from inside the vehicle.
Type 2
To open the tailgate, insert the key and turnit clockwise to unlatch and lift the tailgate.
60M-02-010
NOTICEDo not use the key to lift up the tail-gate, or the key may break off in thelock.
60M-02-011
You can also unlatch the tailgate by pullingthe release lever located on the outboardside of the driver’s seat.
Keyless Entry System Transmitter(if equipped)
60M-02-012
1) “LOCK” button2) “UNLOCK” button
You can lock or unlock all doors (includingthe tailgate) simultaneously by operating thetransmitter near the vehicle.
2-4
BEFORE DRIVING
20
76G-74E
• To lock the doors, push the “LOCK” but-ton (1) on the transmitter.
• To unlock the doors, push the“UNLOCK” button (2) on the transmitter.
The turn signal lights will flash once whenthe doors are locked.
When the doors are unlocked:• The turn signal lights will flash twice.• If the interior light switch is in the
“DOOR” position, the interior light willturn on for about 15 seconds and thenfade out. If you insert the key into theignition switch during this time, the lightwill start to fade out immediately.
Be sure the doors are locked after youoperate the “LOCK” button (1).
NOTE:If no door is opened within about 30 sec-onds after the “UNLOCK” button (2) isoperated, the doors will automatically lockagain.
NOTE:• The maximum operating distance of the
keyless entry system transmitter is about5 m (16 ft.), but this can vary dependingon the surroundings, especially nearother transmitting devices such as radiotowers or CB (Citizen’s Band) radios.
• The door locks cannot be operated withthe transmitter, if the ignition key is
inserted in the ignition switch.• When any door is open, the door locks
can be operated only unlock with thetransmitter, and the turn signal light willnot flash.
• If you lose one of the transmitters, askyour MARUTI SUZUKI dealer as soonas possible for a replacement. Be sureto have your dealer program the newtransmitter code in your vehicle’smemory so that the old code is erased.
NOTICEThe transmitter is a sensitive elec-tronic instrument. To avoid damagingthe transmitter:• Do not expose it to impacts, mois-
ture or high temperature such as byleaving it on the dashboard underdirect sunlight.
• Keep the transmitter away frommagnetic objects such as a televi-sion.
Replacement of the BatteryIf the transmitter becomes unreliable,replace the battery.
To replace the battery of the transmitter:
60M-02-013
1) Remove the screw (1), and open thetransmitter cover.
2) Remove the transmitter (2).
60M-02-014
(3) Lithium disc type battery:CR1620 or equivalent
2-5
BEFORE DRIVING
21
76G-74E
3) Put the edge of a flat blade screwdriverin the slot of the transmitter (2) and pryit open.
4) Replace the battery (3) so its + terminalfaces the “+” mark of the transmitter.
5) Close the transmitter and install it intothe transmitter holder.
6) Close the transmitter cover, install andtighten the screw (1).
7) Make sure the door locks can be oper-ated with the transmitter.
8) Dispose of the used battery properlyaccording to applicable rules or regula-tions. Do not dispose of lithium batter-ies with ordinary household trash.
wwwww WARNINGSwallowing a lithium battery maycause serious internal injury. Do notallow anyone to swallow a lithiumbattery. Keep lithium batteries awayfrom children and pets. If swallowed,contact a physician immediately.
NOTICEThe transmitter is a sensitive elec-tronic instrument. To avoid damagingit, do not expose it to dust or mois-ture or tamper with internal parts.
Security System (if equipped)
If your vehicle is equipped with the securitysystem, contact your dealer for furtherinformation.
WindowsManual Window Control(if equipped)
Driver’s side
60M-02-016
Raise or lower the door windows by turningthe handle located on the door panel.Electric Window Controls(if equipped)The electric windows can only be operatedwhen the ignition switch is in the “ON” posi-tion.
60M-02-017
60M-02-015
The driver’s door has a switch (1) to oper-ate the driver’s window, and a switch (2)to operate the front passenger’s window orthere are switches (3), (4), to operate therear right and left passenger windows,respectively.
EXAMPLE
Passenger’s door
The passenger’s door has a switch (5) tooperate the passenger’s window.
60M-02-018
EXAMPLE
2-6
BEFORE DRIVING
EXAMPLE
22
76G-74E
To open a window, push the top part of theswitch and to close the window lift up thetop part of the switch.The driver’s window has an “auto-down”feature for added convenience (at tollbooths or drive-through restaurants, forexample). This means you can open thewindow without holding the window switchin the “Down” position. Press the driver’swindow switch completely down and releaseit. To stop the window before it reaches thebottom, pull the switch up briefly.
Lock switch
60M-02-019
The driver’s door also has a lock switch forthe passenger’s windows. When you pushin the lock switch, the passenger’s windowscannot be raised or lowered by operatingany of the switches (2), (3), (4) or (5). Torestore normal operation, release the lockswitch by pushing again.
60M-02-020
wwwww WARNINGYou should always lock the passen-ger’s window operation when there arechildren in the vehicle. Children canbe seriously injured if they get part oftheir body caught by the windowduring operation.To avoid injuring an occupant bywindow entrapment, be sure no partof the occupant’s body such as handsor head is in the path of the electricwindows when closing them.Always remove the ignition key whenleaving the vehicle even if only for ashort time. Also do not leave childrenalone in a parked vehicle. Unattendedchildren could use the electric windowswitches and get trapped by thewindow.
MirrorsInside Rearview MirrorYou can adjust the inside rearview mirrorby hand so as to see the rear of your vehi-cle in the mirror.
Type 1
NOTE:If you drive with one of the rear windowsopen, you may hear a loud sound causedby air vibration. To reduce the sound, openthe driver’s or front passenger’s window, ornarrow the rear window opening.
60M-02-021
Type 2
60M-02-022
2) Day driving3) Night driving
60M-02-023
2-7
BEFORE DRIVING
EXAMPLE
23
76G-74E
To adjust the mirror, set the selector tab (1)to the day position, then move the mirrorup, down or sideways by hand to obtain thebest view.
When driving at night, you can move theselector tab to the night position to reduceglare from the headlights of vehicles behindyou.
wwwww WARNING• Always adjust the mirror with the
selector set to the day position.• Only use the night position if it is
necessary to reduce glare from theheadlights of vehicles behind you.Be aware that in this position youmay not be able to see someobjects that could be seen in theday position.
Outside Rearview MirrorsAdjust the outside rearview mirrors so youcan just see the side of your vehicle in themirrors.
wwwww WARNINGBe careful when judging the size ordistance of a vehicle or other objectseen in the side convex mirror. Beaware that objects look smaller andappear farther away than when seenin a flat mirror.
Type 1
60M-02-024
You can adjust the outside rearview mirrorsby hand with the knob (1) located on thedriver’s or front passenger’s door panel.
Type 2
60M-02-025
The switch to control the electric mirrors islocated on the driver’s door panel. You canadjust the mirrors when the ignition switchis in the “ACC” or “ON” position. To adjustthe mirrors:
1) Move the selector switch to the left orright to select the mirror you wish toadjust.
2) Press the outer part of the switch thatcorresponds to the direction in which youwish to move the mirror.
3) Return the selector switch to the centerposition to help prevent unintendedadjustment.
Front Seats
Seat Adjustment
wwwww WARNINGNever attempt to adjust the driver’sseat or seatback while driving. Theseat or seatback could move unex-pectedly, causing loss of control.Make sure that the driver’s seat andseatback are properly adjusted beforeyou start driving.
wwwww WARNINGTo avoid excessive seat belt slack,which reduces the effectiveness of theseat belts as a safety device, makesure that the seats are adjusted beforethe seat belts are fastened.
2-8
BEFORE DRIVING
EXAMPLE
24
76G-74E
Adjusting Seat Position
The adjustment lever for each front seat islocated under the front of the seat. Toadjust the seat position, pull up on theadjustment lever and slide the seat forwardor rearward.After adjustment, try to move the seat for-ward and rearward to ensure that it issecurely latched.
60M-02-026
60M-02-027
If the driver’s seat is equipped with a seatheight adjuster lever on the outboard sideof the seat, raise or lower the seat by pull-ing up or down the adjuster lever.
Adjusting Seatbacks
wwwww WARNINGAll seatbacks should always be in anupright position when driving, or seatbelt effectiveness may be reduced.Seat belts are designed to offer maxi-mum protection when seatbacks are inthe upright position.
60M-02-028
To adjust the seatback angle of front seats,pull up the lever on the outboard side ofthe seat, move the seatback to the desiredposition, and release the lever to lock theseatback in place.
Head Restraints
60M-02-029
EXAMPLE
EXAMPLE EXAMPLE
2-9
BEFORE DRIVING
25
76G-74E
Head restraints are designed to help reducethe risk of neck injuries in the case of anaccident. Adjust the head restraint to theposition which places the center of the headrestraint closest to the top of your ears. Ifthis is not possible for very tall passengers,adjust the head restraint as high aspossible.
wwwww WARNING• Never drive the vehicle with the
head restraints removed.• Do not attempt to adjust the head
restraint while driving.
NOTEIt may be necessary to recline the seatbackto provide enough overhead clearance toremove the head restraint.
Front
60M-02-030
To raise the front head restraint, pull upwardon the restraint until it clicks. To lower therestraint, push down on the restraint whileholding in the lock lever. If a head restraintmust be removed (for cleaning, replacement,etc.), push in the lock lever and pull thehead restraint all the way out.
Rear SeatsSeat Adjustment
wwwww WARNINGTo avoid excessive seat belt slack,which reduces the effectiveness of theseat belts as a safety device, makesure that the seats are adjusted beforethe seat belts are fastened.
Adjusting Seat Position(for 2nd row seats)
60M-02-031
The adjustment levers for 2nd row seats arelocated under the front of the seats. Toadjust the seat position, pull up on theadjustment lever and slide the seat forwardor rearward.After adjustment, try to move the seat for-ward and rearward to ensure that it issecurely latched.
NOTICEWhen the 3rd row seat is folded for-ward, adjust the 2nd row seat not toreach the 3rd row seat.
Adjusting Seatbacks
wwwww WARNINGAll seatbacks should always be in anupright position when driving, or seatbelt effectiveness may be reduced.Seat belts are designed to offer maxi-mum protection when seatbacks are inthe upright position.
2-10
BEFORE DRIVING
EXAMPLEEXAMPLE
26
76G-74E
For 2nd row seats
To adjust the seatback angle of 2nd rowseats, pull up the lever on the outboard sideof the seat, move the seatback to thedesired position, and release the lever tolock the seatback in place.
60M-02-032 60M-02-033
Walk-in Type Seats(for 2nd row seats)
NOTE:To enter to or exit from the 3rd row seat,hook the webbing of the outboard lap-shoulder belt of 2nd row seat before mov-ing the 2nd row seat.
60M-02-034
The walk-in type seat can be moved to pro-vide easy entry to and exit from the 3rd rowseats. You can move a walk-in seat by pull-ing up the lever on the outboard side of theseatback and pushing the seatback forward.
wwwww WARNING• After using the walk-in function, be
sure to return the folded seat backto an upright position.
• Before returning a walk-in seat to itsnormal seating position, make surethat the feet of the passenger in the3rd row seat are out of the way.
• After returning the seat to its nor-mal seating position, make sure it issecurely latched.
wwwww WARNING• Never drive the vehicle with the
head restraints removed.• Do not attempt to adjust the head
restraint while driving.
Head Restraints (if equipped)Head restraints are designed to help reducethe risk of neck injuries in the case of anaccident.
NOTE:It may be necessary to fold forward the
2-11
BEFORE DRIVING
EXAMPLE
EXAMPLE
27
76G-74E
seatback to provide enough overheadclearance to remove the head restraint.
Adjust the head restraint to the positionwhich places the center of the head restraintclosest to the top of your ears. If this is notpossible for very tall passengers, adjust thehead restraint as high as possible.
2nd row seats (if equipped)
3rd row seats (if equipped)
60M-02-035
60M-02-036
EXAMPLE
To raise the rear head restraint, pull upwardon the restraint until it clicks. To lower therestraint, push down on the restraint whileholding in the lock lever. If a head restraintmust be removed (for cleaning, replacement,etc.), push in the lock lever and pull thehead restraint all the way out.
When installing a child restraint system,raise the head restraint to the most upperposition.
Folding Rear SeatsThe rear seat of your vehicle can be foldedforward to provide additional cargo space.
2nd row seats
To fold the 2nd row seat forward:
1) Hook the webbing of the outboard lap-shoulder belts in the belt hangers.
60M-02-037
NOTICE• When you move a seatback, make
sure the belt webbing is hooked inthe seat belt hangers so the seatbelts are not caught by theseatback. This helps preventdamage to the belt system.
• Make sure the belt webbing is nottwisted.
2) Lower the head restraint (if equipped)fully.
3) Store the seat belt buckles in the seatcushion slit.
2-12
BEFORE DRIVING
EXAMPLEEXAMPLE
28
76G-74E
4) Pull up the lever on the outboard sideof the seat, and fold the seatbackforward.
60M-02-038
EXAMPLE
NOTICEWhen the 2nd row seat head restraintreaches the front seatback, slide thefront seat forward.
wwwww WARNINGIf you need to carry cargo in the pas-senger compartment with the 2nd rowseatback folded forward, be sure tosecure the cargo or it may be thrownabout, causing injury. Never pile cargohigher than the seatback.
Raise the seatback until it locks into place.
NOTE:When the seatback is locked in the foldedposition, pull up the lever on the outboardside of the seat to unlatch the seatback.
After returning the seat, try moving theseatback to make sure they are securelylatched.
3rd row seats
To fold the 3rd row seat forward:1) Lower the head restraint (if equipped)
fully.2) Store the seat belt buckles in the seat
cushion slit.
60M-02-039
60M-02-040
NOTICE
To return the seat to the normal position,follow the procedure below.
EXAMPLE
EXAMPLE
3) Pull up the both release straps on thetop of seat, and fold the seatback for-ward.
When the 3rd row seat head restraintreaches the 2nd row seatback, slidethe 2nd row seat forward (if requiredremove head restraint).
wwwww WARNINGIf you need to carry cargo in the pas-senger compartment with the 3rd rowseatback folded forward, be sure tosecure the cargo or it may be thrownabout, causing injury. Never pile cargohigher than the seatback.
2-13
BEFORE DRIVING
29
76G-74E
To return the seat to the normal position,follow the procedure below.
Raise the seatback until it locks into place.
When you raise the seat from back of it,pull the strap (1).
60M-02-041
NOTICEDo not pull the luggage flap (2) (ifequipped) or place any luggage whenthe luggage flap is pull toward rear.Otherwise, the luggage flap (2) will bedamaged.
After returning the seat, try moving theseatback to make sure they are securelylatched.
Seat Belts and Child RestraintSystems
60M-02-042
wwwww WARNINGWear Your Seat Belts at All Times.
wwwww WARNINGAn air bag supplements, or adds to,the frontal crash protection offered byseat belts. The driver and all pas-sengers must be properly restrainedby wearing seat belts at all times,whether or not an air bag is mountedat their seating position, to minimizethe risk of severe injury or death inthe event of a crash.
wwwww WARNING
60M-02-043
• Never allow persons to ride in thecargo area of a vehicle. In the eventof an accident, there is a muchgreater risk of injury for personswho are not riding in a seat withtheir seat belt securely fastened.
• Seat belts should always beadjusted as follows:– the lap portion of the belt should
be worn low across the pelvis, notacross the waist.
– the shoulder straps should beworn on the outside shoulderonly, and never under the arm.
– the shoulder straps should beaway from your face and neck,but not falling off your shoulder.
VV VVV
2-14
BEFORE DRIVING
EXAMPLE
30
76G-74E
60M-02-044
wwwww WARNING
VVVV V• Seat belts should never be wornwith the straps twisted and shouldbe adjusted as tightly as is com-fortable to provide the protection forwhich they have been designed. Aslack belt will provide less pro-tection than one which is snug.
• Make sure that each seat belt buckleis inserted into the proper bucklecatch. It is possible to cross thebuckles in the rear seat.
60M-02-045
VV VVV
wwwww WARNING
VVVV V
VV VVV
• Pregnant women should use seatbelts, although specific recommen-dations about driving should bemade by the woman’s medical advi-sor. Remember that the lap portionof the belt should be worn as lowas possible across the hips, asshown in the diagram.
• Do not wear your seat belt overhard or breakable objects in yourpockets or on your clothing. If anaccident occurs, objects such asglasses, pens, etc. under the seatbelt can cause injury.
• Never use the same seat belt on morethan one occupant and never attach a
wwwww WARNING
VVVV V seat belt over an infant or child beingheld on an occupant’s lap. Such seatbelt use could cause serious injury inthe event of an accident.
• Periodically inspect seat beltassemblies for excessive wear anddamage. Seat belts should be replacedif webbing becomes frayed,contaminated, or damaged in any way.It is essential to replace the entire seatbelt assembly after it has been wornin a severe impact, even if damage tothe assembly is not obvious.
• Children age 12 and under should rideproperly restrained in the rear seat.
• Infants and small children shouldnever be transported unless they areproperly restrained. Restraintsystems for infants and small chil-dren can be purchased locally andshould be used. Make sure that thesystem you purchase meets appli-cable safety standards. Read andfollow all the directions provided bythe manufacturer.
• For children, if the shoulder beltirritates the neck or face, move thechild closer to the center of thevehicle.
• Avoid contamination of seat belt
VV VVV
2-15
BEFORE DRIVING
31
76G-74E
wwwww WARNINGVVVV V webbing by polishes, oils, chemi-
cals, and particularly battery acid.Cleaning may safely be carried outusing mild soap and water.
• Do not insert any items such ascoins, clips, etc. into the seat beltbuckles, and be careful not to spillliquids into these parts. If foreignmaterials get into a seat belt buckle,the seat belt may not work properly.
• All seatbacks should always be inan upright position when driving, orseat belt effectiveness may bereduced. Seat belts are designed tooffer maximum protection whenseatbacks are in the upright posi-tion.
Lap-Shoulder Belt
Emergency Locking Retractor (ELR)The seat belt has an emergency lockingretractor (ELR), which is designed to lockthe seat belt only during a sudden stop orimpact. It also may lock if you pull the beltacross your body very quickly. If this hap-pens, let the belt go back to unlock it, thenpull the belt across your body more slowly.
Safety reminder
60M-02-046
60M-02-047
To reduce the risk of sliding under the beltduring a collision, position the lap portionof the belt across your lap as low on yourhips as possible and adjust it to a snug fitby pulling the shoulder portion of the beltupward through the latch plate. The length
of the diagonal shoulder strap adjusts itselfto allow freedom of movement.
All Seat Belts Except Center of 2ndRow Seat
60M-02-048
To fasten the seat belt, sit up straight andwell back in the seat, pull the latch plateattached to the seat belt across your bodyand press it straight into the buckle until youhear a “click”.
2-16
BEFORE DRIVING
32
76G-74E
60M-02-049
To unfasten the seat belt, push the buttonon the buckle and retract the belt slowlywhile attaching a hand to the belt or/and thelatch plate.
Center Seat Belt of 2nd Row SeatLap belt
60M-02-050
Sit up straight and well back in the seat.To fasten the belt, pull the latch plateattached to the seat belt across your hipsand press it straight into the buckle until youhear a “click”. To reduce the risk of slidingunder the belt during a collision, position thebelt across your lap as low on your hipsas possible and adjust it to a snug fit.To tighten the belt, pull the free end of thebelt across alongside the lap strap.
60M-02-051
To lengthen, release the latch plate from thebuckle, pull the latch plate (adjuster) in thedirection of the arrow. The latch plateshould then be refitted into the buckle andthe belt tightened as previously described.
EXAMPLE
60M-02-053
NOTE:The word “CENTER” is marked into thebuckle for the rear center belt. The bucklesare designed so a latch plate cannot beinserted into the wrong buckle.
Driver’s Seat Belt Reminder
60M-02-052
When the driver does not buckle his or herseat belt with the ignition switch in the “ON”position, the driver’s seat belt reminder lightin the instrument cluster will blink until thedriver’s seat belt is buckled.
2-17
BEFORE DRIVING
TO TIGHTEN
TO LOOSEN
EXAMPLE
33
76G-74E
The reminder will be automatically canceledwhen the driver’s seat belt is buckled or theignition switch is turned off.
wwwww WARNINGIt is absolutely essential that thedriver and passengers wear their seatbelts at all times. Persons who are notwearing seat belts have a muchgreater risk of injury if an accidentoccurs. Make a regular habit of buck-ling your seat belt before putting thekey in the ignition.
60M-02-054
Shoulder Anchor Height Adjuster(if equipped)
Adjust the shoulder anchor height so thatthe shoulder belt rides on the center of the
outboard shoulder. To move upward, slidethe anchor up. To move downward, slidethe anchor down while pulling the lock knobout. After adjustment, make sure that theanchor is securely locked.
Be sure that the shoulder belt is posi-tioned on the center of the outsideshoulder. The belt should be awayfrom your face and neck, but not fall-ing off your shoulder. Misadjustmentof the belt could reduce the effective-ness of the safety belt in a crash.
wwwww WARNING
Seat Belt Hanger (for 2nd row seats)
60M-02-055
NOTE:To enter to or exit from the 3rd row seat,hook the webbing of the outboard lap-
shoulder belt of 2nd row seat before mov-ing the 2nd row seat.
Seat Belt Inspection
Periodically inspect the seat belts to makesure they work properly and are not dam-aged. Check the webbing, buckles, latchplates, retractors, anchorages, and guideloops. Replace any seat belts which do notwork properly or are damaged.
60M-02-056
wwwww WARNINGBe sure to inspect all seat beltassemblies after any collision. Anyseat belt assembly which was in useduring a collision (other than a veryminor one) should be replaced, evenif damage to the assembly is not
VV VVV
2-18
BEFORE DRIVING
EXAMPLEEXAMPLE
EXAMPLE
34
76G-74E
wwwww WARNINGVVVV Vobvious. Any seat belt assembly
which was not in use during a colli-sion should be replaced if it does notfunction properly, it is damaged in anyway or the seat belt pretensioners (ifequipped) were activated (that is, ifthe front air bags were activated).
Child Restraint Systems
60M-02-057
Infant restraint - rear seat only
60M-02-058
Child restraint
60M-02-059
Booster seat
60M-02-060
EXAMPLE EXAMPLE
MARUTI SUZUKI highly recommends thatyou use a child restraint system to restraininfants and small children. Many differenttypes of child restraint systems areavailable; make sure that the restraintsystem you select meets applicable safetystandards.
All child restraint systems are designed tobe secured in vehicle seats by either seatbelts (lap belts or the lap portion of lap-shoulder belts). Whenever possible, MARUTISUZUKI recommends that child restraintsystems be installed on the rear seat.According to accident statistics, children aresafer when properly restrained in rearseating positions than in front seating posi-tions.
2-19
BEFORE DRIVING
EXAMPLE
35
76G-74E
If you must use a front-facing child restraintin the front passenger’s seat, adjust thepassenger’s seat as far back as possible.
NOTE:Observe any statutory regulation about childrestraints.
60M-02-061
wwwww WARNINGIf your vehicle is equipped with a frontpassenger air bag, do not install arear-facing child restraint in the frontpassenger’s seat. If the passenger’sair bag inflates, a child in a rear-facingchild restraint could be killed orseriously injured. The back of a rear-facing child restraint would be tooclose to the inflating air bag.
wwwww WARNINGIf you install a child restraint systemin the 2nd row seat, slide the seatinstalled the child restraint system asfar back as possible. If you install achild restraint system in the 3rd rowseat, slide the seat in front of the seatinstalled a child restraint systemenough forward so that the child’sfeet do not contact the front seatback.These will help avoid injury to thechild in the event of an accident.
60M-02-062
60M-02-063
wwwww WARNINGChildren could be endangered in acrash if their child restraint systemsare not properly secured in the vehi-cle. When installing a child restraintsystem, be sure to follow the instruc-tions below. Be sure to secure thechild in the restraint system accord-ing to the manufacturer’s instructions.
wwwww WARNINGIn an accident or sudden stop, therear seat armrest (if equipped) couldfall forward. If there is a child in arear-facing child restraint in the cen-ter seating position, the falling armrestcould injure the child. Make sure thearmrest is back in the seat when notin use.
2-20
BEFORE DRIVING
36
76G-74E
Installation with Lap-Shoulder SeatBelts
NOTICEBefore installing a child restraint sys-tem in the rear seat, raise the headrestraint (if equipped) to the mostupper position.
ELR type belt
60M-02-064
Install your child restraint system accordingto the instructions provided by the childrestraint system manufacturer.
Make sure that the seat belt is securelylatched.
Try to move the child restraint system in alldirections to make sure it is securelyinstalled.
Installation with a Lap Belt
60M-02-065
Install your child restraint system accordingto the instructions provided by the childrestraint system manufacturer.
To lengthen or tighten the belt, refer to the“Lap-belt” item in this “Seat Belts and ChildRestraint Systems” section. After makingsure that the seat belt is securely latched,try moving the child restraint system in alldirections, to make sure it is securelyinstalled. If you need to tighten the belt, pullthe free end of the webbing.
Seat Belt Pretensioner System(if equipped)
60M-02-066
This section of the owner’s manualdescribes your MARUTI SUZUKI SEATBELT PRETENSIONER SYSTEM.Please read and follow ALL theseinstructions carefully to minimize yourrisk of severe injury or death.
wwwww WARNING
To determine if your vehicle is equippedwith a seat belt pretensioner system at thefront seating positions, check the label onthe front seat belt at the bottom part. If theletters “p” and/or “PRE” appear as illus-trated, your vehicle is equipped with theseat belt pretensioner system. You can usethe pretensioner seat belts in the samemanner as ordinary seat belts.
2-21
BEFORE DRIVING
EXAMPLE
EXAMPLEEXAMPLE
37
76G-74E
Read this section and the “SupplementalRestraint System (air bags)” section to learnmore about the pretensioner system.
The seat belt pretensioner system workswith the SUPPLEMENTAL RESTRAINTSYSTEM (Air Bags). The crash sensors andthe electronic controller of the air bagsystem also control the seat belt preten-sioners. When the air bags are triggered,the pretensioner are also triggered. Forprecautions and general informationincluding servicing the pretensioner system,refer to the “Supplemental Restraint System(air bags)” section in addition to this “SeatBelt Pretensioner System” section, andfollow all those precautions.
The pretensioner is located in each frontseat belt retractor. The pretensioner tight-ens the seat belt so the belt fits the occu-pant’s body more snugly in the event of afrontal crash. The retractors will remainlocked after the pretensioners are activated.Upon activation, some noise will occur andsome smoke may be released. Theseconditions are not harmful and do notindicate a fire in the vehicle.The driver and all passengers must beproperly restrained by wearing seat belts atall times, whether or not a pretensioner isequipped at their seating position, tominimize the risk of severe injury or deathin the event of a crash.
Sit fully back in the seat; sit up straight; donot lean forward or sideways. Adjust the beltso the lap portion of the belt is worn lowacross the pelvis, not across the waist.Please refer to the “Seat Adjustment” sec-tion and the instructions and precautionsabout the seat belts in this “Seat Belts andChild Restraint Systems” section for detailson proper seat and seat belt adjustments.
Please note that the pretensioners along withthe air bags will activate in severe frontalcollisions. They are not designed to activatein rear impacts, side impacts, rollovers, orminor frontal collisions. The pretensionerscan be activated only once. If thepretensioners are activated (that is, if the airbags are activated), have the pretensionersystem serviced by an authorized MARUTISUZUKI dealer as soon as possible.
If the “AIR BAG” light on the instrumentcluster does not blink or come on brieflywhen the ignition switch is turned to the“ON” position, stays on for more than 10seconds, or comes on while driving, thepretensioner system or the air bag systemmay not work properly. Have both systemsinspected by an authorized MARUTISUZUKI dealer as soon as possible.
Service on or around the pretensioner sys-tem components or wiring must be per-formed only by an authorized MARUTI
SUZUKI dealer who is specially trained.Improper service could result in unintendedactivation of pretensioners or could renderthe pretensioner inoperative. Either of thesetwo conditions may result in personal injury.
To prevent damage or unintended activationof the pretensioners, be sure the battery isdisconnected and the ignition switch hasbeen in the “LOCK” position for at least 90seconds before performing any electricalservice work on your MARUTI SUZUKI.
Do not touch pretensioner system compo-nents or wiring. The wires are wrapped withyellow tape or yellow tubing, and thecouplers are yellow. When scrapping yourMARUTI SUZUKI, ask your MARUTISUZUKI dealer, body repair shop, or scrapyard for assistance.
Supplemental Restraint System (airbags) (if equipped)
This section of the owner’s manualdescribes the protection provided byyour MARUTI SUZUKI’s SUPPLEMENTALRESTRAINT SYSTEM (air bags).Please read and follow ALL theseinstructions carefully to minimize yourrisk of severe injury or death in theevent of a collision.
wwwww WARNING
2-22
BEFORE DRIVING
38
76G-74E
Your vehicle is equipped with a Supple-mental Restraint System consisting of thefollowing components in addition to a lap-shoulder belt at each front seating position.
1) Driver’s front air bag module(if equipped)
2) Front passenger’s front air bag module(if equipped)
3) Seat belt pretensioners (if equipped)4) Air bag controller (if equipped)5) Forward crash sensor (if equipped)
60M-02-067
60M-02-068
If the “AIR BAG” light on the instrumentcluster does not blink or come on when theignition switch is first turned to the “ON”position, or the “AIR BAG” light stays on,or comes on while driving, the air bagsystem (or the seat belt pretensionersystem) may not work properly. Have theair bag system inspected by an authorizedMARUTI SUZUKI dealer as soon aspossible.
Front Air Bags
60M-02-069
EXAMPLE 60M-02-070
60M-02-071
EXAMPLE
The driver’s front air bag is located behindthe center pad of the steering wheel andthe front passenger’s front air bag is locatedbehind the passenger’s side of thedashboard. The words “SRS AIRBAG” aremolded into the air bag covers to identifythe location of the air bags.2-23
BEFORE DRIVING
EXAMPLE
EXAMPLE
39
76G-74E
Frontal collision range
60M-02-072
Front air bags are designed to inflate insevere frontal collisions.
Front air bags will not inflate
60M-02-073
Front air bags will probably not inflate
60M-02-074
Front air bags are not designed to inflatein rear impacts, side impacts, rollovers orminor frontal collisions, since they wouldoffer no protection in those types of acci-dents. Remember, since an air bag deploysonly one time during an accident, seat beltsare needed to restrain occupants fromfurther movements during the accident.
Therefore, an air bag is NOT a substitutefor seat belts. To maximize your protection,ALWAYS WEAR YOUR SEAT BELTS. Beaware that no system can prevent all pos-sible injuries that may occur in an accident.
wwwww WARNINGAn air bag supplements, or adds to,the crash protection offered by seat
VV VVV
wwwww WARNING
VVVV V
belts. The driver and all passengersmust be properly restrained by wear-ing seat belts at all times, whether ornot an air bag is mounted at theirseating position, to minimize the riskof severe injury or death in the eventof a crash.
60M-02-075
wwwww WARNINGDo not install a rear-facing child restraintin the front passenger’s seat. If thepassenger’s front air bag inflates, a childin a rear-facing child restraint could bekilled or severely injured. The back of arear-facing child restraint would be tooclose to the inflating air bag.
2-24
BEFORE DRIVING
40
76G-74E
If you must use a front-facing child restraintin the front passenger’s seat, be sure tomove the front passenger’s seat as far backas possible. Please refer to “Seat Belts andChild Restraint Systems” in this section fordetails on securing your child.
Air bag symbol (if equipped) meaning
60M-02-076
You may find this label on the sun visor.
wwwww WARNINGDo not use a rearward facing childrestraint on a seat protected by anairbag in front of it.
wwwww WARNINGIf the AIR BAG light in the instrumentcluster ever comes on and stays on,
VV VVV
wwwww WARNING
it means that something may bewrong with the air bag system. If thisever happens, have the vehicle ser-viced immediately, because the airbags may not offer the protection forwhich they were designed.
VVVV V
How the System WorksIn a frontal collision, the crash sensors willdetect rapid deceleration, and if the con-troller judges that the deceleration repre-sents a severe frontal crash, the controllerwill trigger the inflators. The inflators inflatethe appropriate air bags with nitrogen orargon gas. The inflated air bags provide acushion for your head and upper body. Theair bag inflates and deflates so quickly thatyou may not even realize that it has acti-vated. The air bag will neither hinder yourview nor make it harder to exit the vehicle.
Air bags must inflate quickly and forcefullyin order to reduce the chance of serious orfatal injuries. However, an unavoidableconsequence of the quick inflation is thatthe air bag may irritate bare skin, such asthe facial area against a front air bag. Also,upon inflation, a loud noise will occur andsome powder and smoke will be released.These conditions are not harmful and do notindicate a fire in the vehicle. Be aware,
however, that some air bag componentsmay be hot for a while after inflation.
A seat belt helps keep you in the properposition for maximum protection when an airbag inflates. Adjust your seat as far backas possible while still maintaining control ofthe vehicle. Sit fully back in your seat; situp straight; do not lean over the steeringwheel or dashboard. Please refer to the“Seat Adjustment” section and the “SeatBelts and Child Restraint Systems” in thissection for details on proper seat and seatbelt adjustments.
60M-02-077
wwwww WARNING• The driver should not lean over the
steering wheel. The front passengershould not rest his or her body
VV VVV
2-25
BEFORE DRIVING
41
76G-74E
wwwww WARNING
against the dashboard, or otherwiseget too close to the dashboard. Inthese situations, the out-of-positionoccupant would be too close to aninflating air bag, and may suffersevere injury.
• Do not attach any objects to, orplace any objects over, the steeringwheel or dashboard. Do not placeany objects between the air bag andthe driver or front passenger. Theseobjects may interfere with air bagoperation or may be propelled bythe air bag in the event of a crash.Either of these conditions maycause severe injury.
VVVV V
Note that even though your vehicle may bemoderately damaged in a collision, the col-lision may not have been severe enough totrigger the air bags to inflate. If your vehiclesustains ANY front-end or side damage,have the air bag system inspected by anauthorized MARUTI SUZUKI dealer toensure it is in proper working order.
Your vehicle is equipped with a diagnosticmodule which records information about theair bag system if the air bags deploy in acrash. The module records informationabout overall system status, which sensorsactivated the deployment.
Servicing the air bag systemIf the air bags inflate, have the air bags andrelated components replaced by an autho-rized MARUTI SUZUKI dealer as soon aspossible.
If your vehicle ever gets in deep water andthe driver’s floor is submerged, the air bagcontroller could be damaged. If it does,have the air bag system inspected by theMARUTI SUZUKI dealer as soon aspossible.
Special procedures are required for servic-ing or replacing an air bag. For that reason,only an authorized MARUTI SUZUKI dealershould be allowed to service or replace yourair bags. Please remind anyone whoservices your MARUTI SUZUKI that it hasair bags.
Service on or around air bag componentsor wiring must be performed only by anauthorized MARUTI SUZUKI dealer.Improper service could result in unintendedair bag deployment or could render the airbag inoperative. Either of these twoconditions may result in severe injury.
To prevent damage or unintended inflationof the air bag system, be sure the batteryis disconnected and the ignition switch hasbeen in the “LOCK” position for at least 90seconds before performing any electricalservice work on your MARUTI SUZUKI. Do
not touch air bag system components orwires. The wires are wrapped with yellowtape or yellow tubing, and the couplers areyellow for easy identification.
Scrapping a vehicle that has an uninflatedair bag can be hazardous. Ask your dealer,body repair shop or scrap yard for help withdisposal.
2-26
BEFORE DRIVING
42
76G-74E
60M-02-079
60M-02-078
Instrument Cluster
1. Speedometer2. Tachometer (if equipped)3. Fuel gauge4. Temperature gauge5. Information display6. Trip meter selector knob7. Indicator selector knob8. Warning and indicator lights
with tachometer
* These marks are explanation of the knobs6 and 7. Refer to “Brightness Control” or“Information Display” in this section for detailof knobs.
without tachometer
* These marks are explanation of the knobs6 and 7. Refer to “Brightness Control” or“Information Display” in this section for detailof knobs.
2-27
BEFORE DRIVING
43
76G-74E
Warning and Indicator Lights
Brake System Warning Light
60M-02-080
Three different types of operations existdepending on the vehicle’s specification.
1) The light comes on briefly when theignition switch is turned to the “ON”position.
2) The light comes on when the parkingbrake is engaged with the ignition switchin the “ON” position.
3) The light comes on when under eitheror both of above two conditions.
The light also comes on when the fluid inthe brake fluid reservoir falls below thespecified level.
The light should go out after starting theengine and fully releasing the parking brake,if the fluid level in the brake fluid reservoiris adequate.
The light also comes on together with theABS warning light when the rear brake forcecontrol function (proportioning valve function)of the ABS system fails.
If the brake system warning light comes onwhile you are driving the vehicle, it maymean that there is something wrong withthe vehicle’s brake system. If this happens,you should:
1) Pull off the road and stop carefully.
wwwww WARNINGRemember that stopping distance maybe longer, you may have to pushharder on the pedal, and the pedalmay go down farther than normal.
2) Test the brakes by carefully starting andstopping on the shoulder of the road.
– If you determine that it is safe, drivecautiously at low speed to the nearestdealer for repairs, or
– Have the vehicle towed to the nearestdealer for repairs.
wwwww WARNINGIf any of the following conditionsoccur, you should immediately askyour MARUTI SUZUKI dealer toinspect the brake system.• If the brake system warning light
does not go out after the enginehas been started and the parkingbrake has been fully released.
• If the brake system warning light
VV VVV
does not come on when the ignitionswitch is turned to the “ON”position.
• If the brake system warning lightcomes on at any time during vehi-cle operation.
wwwww WARNING
VVVV V
NOTE:Because the brake system is self-adjusting,the fluid level will drop as the brake padsbecome worn. Replenishing the brake fluidreservoir is considered normal periodicmaintenance.
NOTE:(Parking Brake Reminder Buzzer)A buzzer sounds intermittently to remindyou to release the parking brake if you drivethe vehicle without releasing the parkingbrake. Make sure that the parking brake isfully released and the brake system warninglight turns off.
Anti-Lock Brake System (ABS)Warning Light (if equipped)
60M-02-081
2-28
BEFORE DRIVING
44
76G-74E
When the ignition switch is turned to the“ON” position, the light comes on briefly soyou can check that the light is working.If the light stays on, or comes on whendriving, there may be something wrong withthe ABS.
If this happens:1) Pull off the road and stop carefully.2) Turn the ignition switch to “LOCK” and
then start the engine again.
If the warning light comes on briefly thenturns off, the system is normal. If the warn-ing light still stays on, there is somethingwrong in the system.
If the light and the brake system warninglight stay on, or come on simultaneouslywhen driving, your ABS system is equippedwith the rear brake force control function(proportioning valve function) and there maybe something wrong with both the rearbrake force control function and anti-lockfunction of the ABS system.
If one of these happens, have the systeminspected by your MARUTI SUZUKI dealer.
If the ABS becomes inoperative, the brakesystem will function as an ordinary brakesystem that does not have this ABS system.
For details of ABS system, refer to “Anti-Lock Brake System (ABS) (if equipped)” in
the “OPERATING YOUR VEHICLE” section.
Oil Pressure Light
60M-02-082
This light comes on when the ignition switchis turned to the “ON” position, and goes outwhen the engine is started. The light willcome on and remain on if there isinsufficient oil pressure. If the light comeson when driving, pull off the road as soonas you can and stop the engine.
Check the oil level and add oil if necessary.If there is enough oil, the lubrication sys-tem should be inspected by your MARUTISUZUKI dealer before you drive the vehicleagain.
NOTICE• If you operate the engine with this
light on, severe engine damage canresult.
• Do not rely on the oil pressure lightto indicate the need to add oil. Besure to periodically check theengine oil level.
Charging Light
60M-02-083
This light comes on when the ignition switchis turned to the “ON” position, and goes outwhen the engine is started. The light willcome on and remain on if there issomething wrong with the battery chargingsystem. If the light comes on when theengine is running, the charging systemshould be inspected immediately by yourMARUTI SUZUKI dealer.
Driver’s seat Belt Reminder Light
60M-02-084
If the driver’s seat belt is unbuckled whenthe ignition switch is turned to the “ON”position, this light will blink until the driver’sseat belt is buckled.For details about the seat belt reminder,refer to “Seat Belts and Child RestraintSystems” in this section.
2-29
BEFORE DRIVING
45
76G-74E
“AIR BAG” Light (if equipped)
60M-02-085
This light blinks or comes on for severalseconds when the ignition switch is turnedto the “ON” position so you can check if thelight is working.
The light will come on and stay on if thereis a problem in the air bag system or theseat belt pretensioner system (if equipped).
wwwww WARNINGIf the “AIR BAG” light does not blinkor come on briefly when the ignitionswitch is turned to the “ON” position,stays on for more than 10 seconds, orcomes on while driving, the air bagsystem or the seat belt pretensionersystem (if equipped) may not workproperly. Have both systems inspectedby an authorized MARUTI SUZUKIdealer.
Malfunction Indicator Light
60M-02-086
Your vehicle has a computer-controlledemission control system. A malfunctionindicator light is provided on the instrumentpanel to indicate when it is necessary tohave the emission control system serviced.The malfunction indicator light comes onwhen the ignition switch is turned to the“ON” position to let you know the light isworking and goes out when the engine isstarted.
If the malfunction indicator light comes on orblinks when the engine is running, there isa damage in the emission control system.
Bring the vehicle to your MARUTI SUZUKIdealer to have the damage fixed.
NOTICEContinuing to drive the vehicle whenthe malfunction indicator light is on orblinking can cause permanent damageto the vehicle’s emission controlsystem, and can affect fuel economyand driveability.
Immobilizer System Light
60M-02-087
When the ignition switch is turn to the“ON” position, this light comes on brieflyso you can check that the light isworking. If this light brinks with theignition switch is turn to the “ON”, theengine will not start.
NOTE:If this light blinks, turn the ignition switchto the “LOCK” position, then turn it back tothe “ON” position.If the light still blinks with the ignition switchturned to the “ON” position, there may besomething wrong with your key or with theimmobilizer system. Ask your MARUTISUZUKI dealer to inspect the system.
Open Door Warning Light
60M-02-088
2-30
BEFORE DRIVING
46
76G-74E
• For vehicles without keyless entry sys-tem;This light remains on until all front doorsand the tailgate are completely closed.
If any door (including the tailgate) isopen when the vehicle is moving, a dingsounds to remind you to close all doorscompletely.
• For vehicles with keyless entry system;This light remains on until all doors(including the tailgate) are completelyclosed.
If any door (including the tailgate) isopen when the vehicle is moving, a dingsounds to remind you to close all doorscompletely.
Low Fuel Warning Light
60M-02-089
If this light comes on, fill the fuel tankimmediately.
When this light comes on, a ding soundsonce to remind you to fill the fuel.If you do not fill the fuel, a ding soundsevery time when the ignition switch is turned
to the “ON” position.
NOTE:The activation point of this light variesdepending on road conditions (for example,slope or curve) and driving conditionsbecause of fuel moving in the tank.
Electric Power Steering Light
Rear Fog Light Indicator Light(if equipped)
60M-02-090
This light comes on when the ignition switchis turned to the “ON” position, and goes outwhen the engine is started.
If this light comes on while driving, thepower steering system may not work prop-erly. Have the system inspected by yourMARUTI SUZUKI dealer.
NOTE:If the power steering system does not workproperly, you will feel heavier to steer butyou still will be able to steer.
NOTE:If the steering is operated, you may heara rubbing noise. This is normal andindicates that the power steering systemworks properly.
60M-02-091
The rear fog light indicator light comes onwhen the rear fog light operates.
Turn Signal Indicators
60M-02-092
When you turn on the left or right turn sig-nals, the corresponding green arrow on theinstrument panel will blink along with therespective turn signal lights. When you turnon the hazard warning switch, both arrows willblink along with all of the turn signal lights.
Main Beam (high beam) Indicator Light
60M-02-093
2-31
BEFORE DRIVING
47
76G-74E
This indicator comes on when headlightmain beams (high beams) are turned on.
Fuel Filter Warning Light(For Diesel Engine Model)
60M-02-094
This light comes on for several secondswhen the ignition switch is turned to the“ON” position so you can check the light isworking.
If the light comes on when driving, there isa possibility to have water in the fuel filter.Drain water as soon as possible. For detailsof draining water, refer to “Fuel Filter” in the“INSPECTION AND MAINTENANCE” section.
Glow Plug Indicator Light(For Diesel Engine Model)
is turned to the “ON” position and goes outwhen the glow plug is heated enough forengine starting.
NOTE:Following the repair on engine control unit(ECU) in the starting system, the glow plugindicator light comes on for approximately10 seconds before the engine starts. Thisis not the engine malfunction.
Speedometer
60M-02-095
If the coolant temperature is cool enough,this light comes on when the ignition switch
60M-02-096
The speedometer indicates vehicle speed inkm/h.
Tachometer (if equipped)
60M-02-097
The tachometer indicates engine speed inrevolutions per minute.
NOTICENever drive the vehicle with the enginerevving in the red zone or severeengine damage can result. Keep theengine speed below the red zone evenwhen downshifting to a lower gearposition. Refer to “Downshifting maxi-mum allowable speeds” in the“OPERATING YOUR VEHICLE” section.
NOTE:Maximum engine speed is limited atapproximately 5000 revolutions per minuteby the fuel cut control when you press theaccelerator pedal while the gearshift is in“N” (Neutral).
2-32
BEFORE DRIVING
EXAMPLE
EXAMPLE
48
76G-74E
Fuel Gauge
When the ignition switch is in the “ON”position, this gauge gives an approximateindication of the amount of fuel in the fueltank. “F” stands for full and “E” stands forempty.
If the indicator gets off the graduation of “E”(not character “E”), refill the tank as soonas possible.
NOTE:The indicator moves a little depending onroad conditions (for example, slope orcurve) and driving conditions because offuel moving in the tank.
If the low fuel warning light (1) comes on,fill the fuel tank immediately.
60M-02-098
When the low fuel warning light (1) comeson, a ding sounds once to remind you tofill the fuel.If you do not fill the fuel, a ding soundsevery time when the ignition switch is turnedto “ON” position.
NOTE:The activation point of the low fuel warninglight (1) varies depending on road conditions(for example, slope or curve) and drivingconditions because of fuel moving in the tank.
The mark (2) indicates that the fuel filler dooris located on the left side of the vehicle.
Temperature Gauge
When the ignition switch is in the “ON”position, this gauge indicates the enginecoolant temperature. Under normal driving
conditions, the indicator should stay withinthe normal, acceptable temperature rangebetween “H” and “C”. If the indicatorapproaches “H”, overheating is indicated.Follow the instructions for engine overheat-ing in the “EMERGENCY SERVICE” section.
NOTICEContinuing to drive the vehicle whenengine overheating is indicated canresult in severe engine damage.
Brightness Control
EXAMPLE
60M-02-100
When the ignition switch is turned to the“ON” position, the pointer lights come on.Your vehicle has a system to automaticallydim the brightness of the instrument panellights when the position lights or headlightsare on.
2-33
BEFORE DRIVING
EXAMPLE
60M-02-099
EXAMPLE
49
76G-74E
When the position lights and/or headlightsare ON, you can control the meter illumina-tion intensity.
To increase the brightness of the instrumentpanel lights, turn the brightness control knob(1) clockwise.
To reduce the brightness of the instrumentpanel lights, turn the brightness control knob(1) counterclockwise.
60M-02-101
EXAMPLE
wwwww WARNINGIf you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.
Do not attempt to adjust the displaywhile driving.
NOTE:• If you do not turn the brightness control
knob within about 5 seconds of activat-ing the brightness control display, thebrightness control display will be can-celed automatically.
• When you reconnect the battery, thebrightness of the instrument panel lightswill be reinitialized. Readjust the bright-ness according to your preference.
Information Display
with tachometer
60M-02-103
EXAMPLE
without tachometer
60M-02-102
EXAMPLE1) Trip meter selector knob2) Indicator selector knob3) Information display
When the ignition switch is in the “ON”position, the information display shows thefollowing information.
Display (A)Thermometer (if equipped)
Display (B)Trip meter / Instantaneous fuel consumption/ Average fuel consumption / Driving range
Display (C)Odometer
2-34
BEFORE DRIVING
50
76G-74E
Display (D)Clock
Thermometer (if equipped)When the ignition switch is in the “ON”position, the display (A) shows the ther-mometer.The thermometer indicates the outsidetemperature.
When the display (B) shows the drivingrange, you can change the unit of tempera-ture.To change the unit of temperature, whilepushing and holding the trip meter selectorknob (1), turn the indicator selector knob(2).
NOTE:When you reconnect the negative (–) ter-minal to the battery, the unit of temperaturewill be reinitialized. Change the unit againto your preference.
60M-02-104
60M-02-105
60M-02-106
meter B, Instantaneous fuel consumption,Average fuel consumption or Driving range.To switch the display indication (B), pushthe trip meter selector knob (1) or the indi-cator selector knob (2) quickly.
EXAMPLE
2-35
BEFORE DRIVING
If the outside temperature nears freezing,the mark (a) will appear on the display.
NOTE:• The outside temperature indication is not
the actual outside temperature whendriving at low speed, or when stopped.
• If there is something wrong with the ther-mometer, or just after the ignition switchis turned to the “ON” position, thedisplay may not indicate the outsidetemperature. Trip meter / Instantaneous fuel con-
sumption / Average fuel consumption /Driving rangeWhen the ignition switch is in the “ON”position, the display (B) shows one of thefollowing five indications, trip meter A, trip
EXAMPLE
EXAMPLE
51
76G-74E
Push the trip meter selectorknob (1).
Push the indicator selectorknob (2).
(b) Trip meter A(c) Trip meter B(d) Instantaneous Fuel Consumption(e) Average fuel consumption(f) Driving range
wwwww WARNINGIf you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.
Do not attempt to adjust the displaywhile driving.
NOTE:• Indications will change when you push
and release a knob.• The display shows estimated values.
Indications may not be the same asactual values.
Trip meterThe trip meter can be used to measure thedistance traveled on short trips or betweenfuel stops.You can use the trip meter A or trip meterB independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (1) for awhile when the display shows the trip meter.
NOTE:The indicated maximum value of the trip meteris 9999.9. When you run past the maximumvalue, the indicated value will return to 0.0.
Instantaneous Fuel ConsumptionThe display shows the value of instanta-neous fuel consumption only when thevehicle is moving.
NOTE:• The display does not show the value
unless the vehicle is moving.• The indicated maximum value of instan-
taneous fuel consumption is 30. No morethan 30 will be indicated on the displayeven if the actual instantaneous fuelconsumption is higher.
• The indication on the display may bedelayed if fuel consumption is greatlyaffected by driving conditions.
• The display shows estimated values.Indications may not be the same asactual values.
• You can change the units that instanta-neous fuel consumption is displayed in.Refer to “Average fuel consumption” inthis section.
Average fuel consumptionIf you selected average fuel consumptionthe last time you drove the vehicle, the dis-play shows the last value of average fuelconsumption from previous driving when the
ignition switch is turned to the “ON” position.Unless you reset the value of average fuelconsumption, the display indicates the valueof average fuel consumption which includesaverage fuel consumption during previousdriving.
To reset the average fuel consumption tozero, push and hold the indicator selectorknob (2) for a while when the display showsthe average fuel consumption.
NOTE:When you reset the indication or reconnectthe negative (–) terminal to the battery, thevalue of average fuel consumption will beshown after driving for a while.
To change the unit of average fuel con-sumption, while pushing and holding the tripmeter selector knob (1), turn the indicatorselector knob (2).
EXAMPLE
2-36
BEFORE DRIVING
60M-02-107
52
76G-74E
NOTE:• When you change the units that average
fuel consumption is displayed in, theinstantaneous fuel consumption units willbe changed automatically.
• When you reconnect the negative (–)terminal to the battery, the unit of theaverage fuel consumption will bereinitialized. Change the unit again toyour preference.
Driving rangeIf you selected driving range the last timeyou drove the vehicle, the display indicates“—-” for a few seconds and then indicatesthe current driving range when the ignitionswitch is turned to the “ON” position.
The driving range shown in the display isthe approximate distance you can drive untilthe fuel gauge indicates “E”, based oncurrent driving conditions.
When the low fuel warning light comes on,the display “—” will appear.
If the low fuel warning light comes on, fillthe fuel tank immediately regardless of thevalue of driving range shown in the display.
As the driving range after refueling is cal-culated based on the most recent drivingcondition, the value is different each timeyou refuel.
NOTE:• If you refuel when the ignition switch is
in the “ON” position, the driving rangemay not indicate the correct value.
• When you reconnect the negative (–)terminal to the battery, the value ofdriving range will be shown after drivingfor a while.
OdometerWhen the ignition switch is in the “ON”position, the display (C) shows the odome-ter.The odometer records the total distance thevehicle has been driven.
NOTICEKeep track of your odometer readingand check the maintenance scheduleregularly for required services.Increased wear or damage to certainparts can result from failure to per-form required services at the propermileage intervals.
ClockWhen the ignition switch is in the “ON”position, the display (D) shows the time.
2) To change the hour indication, turn theindicator selector knob (2) left or rightrepeatedly when the hour indicationblinks. To change the hour indicationquickly, turn and hold the indicatorselector knob (2). To set the hour indi-cation, push the indicator selector knob(2) and the minute indication will blink.
3) To change the minute indication, turn theindicator selector knob (2) left or rightrepeatedly when the minute indicationblinks. To change the minute indicationquickly, turn and hold the indicatorselector knob (2). To set the minuteindication, push the indicator selectorknob (2).
To change the time indication:1) Push the trip meter selector knob (1)
and the indicator selector knob (2)together.
wwwww WARNINGIf you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.Do not attempt to adjust the displaywhile driving.
NOTE:When you reconnect the negative (–) ter-minal to the battery, the clock indication willbe reinitialized. Change the indication againto your preference.
2-37
BEFORE DRIVING
53
76G-74E
Lighting Control Lever
60M-02-108
wwwww WARNINGTo avoid possible injury, do not oper-ate controls by reaching through thesteering wheel.
60M-02-109
OFF (1)All lights are off.
(2)Front position lights, tail lights, license platelight and instrument lights are on, butheadlights are off.
(3)Front position lights, tail lights, license platelight, instrument lights and headlights areon.
Lighting Operation
To turn the lights on or off, twist the knobon the end of the lever. There are threepositions:
EXAMPLE
60M-02-110
EXAMPLE
With the headlights on, push the lever for-ward to switch to the high beams (mainbeams) or pull the lever toward you toswitch to the low beams. When the highbeams (main beams) are on, a light on theinstrument panel will come on. To momen-tarily activate the high beams (main beams)as a passing signal, pull the lever slightlytoward you and release it when you havecompleted the signal.
Light Reminder BuzzerA buzzer sounds to remind you to turn offthe lights if they are left on when the igni-tion key is removed and the driver’s dooris opened.
Rear Fog Light Switch (if equipped)
60M-02-111
To turn the rear fog light on, twist the knobas shown in the illustration with the head-lights are on. When the rear fog light is on,an indicator light on the instrument clusterwill come on.
NOTE:When the knob on the end of the lightningcontrol lever is returned to the “OFF” posi-tion, the rear fog light switch will be can-celed automatically.
Front Fog Light Switch(if equipped)
60M-02-112
2-38
BEFORE DRIVING
EXAMPLE
54
76G-74E
The front fog light comes on when the foglight switch is pushed in with the positionlights, tail lights and/or the headlights areon. An indicator light above the switch willbe lit when the front fog light is on.
NOTE:In some countries the lighting operation maybe different from the above descriptionaccording to local regulations.
Headlight Leveling Switch
60M-02-113
Level the headlight beam according to theload condition of your vehicle by turning thisswitch. The chart below shows theappropriate switch position for differentvehicle-load conditions.
Loading SwitchConditions Position
Driver (1Seat) 0Driver + Co-Driver 0(2 Seats)Driver + Co-Driver +2nd row 3 Seats 1(Total-5 Seats)All Passengers(7 Seats) 2All Passengers +Cargo (Evenly 2Distributed loadin luggage boot)
Driver + Cargo(Evenly distributed 3load in luggage boot)
60M-02-114
Turn Signal Control Lever
wwwww WARNINGTo avoid possible injury, do not oper-ate controls by reaching through thesteering wheel.
Turn Signal OperationWith the ignition switch in the “ON” posi-tion, move the lever up or down to activatethe right or left turn signals.
Normal turn signal
60M-02-115
EXAMPLE
Move the lever all the way upward or down-ward to signal. When the turn is completed,the signal will cancel and the lever willreturn to its normal position.
2-39
BEFORE DRIVING
55
76G-74E
Lane change signal
60M-02-116
Sometimes, such as when changing lanes,the steering wheel is not turned far enoughto cancel the turn signal. For convenience,you can flash the turn signal by moving thelever part way and holding it there. Thelever will return to its normal position whenyou release it.
NOTE:The turn signal and its indicator flash threetimes even if you return the lever immedi-ately after moving it.
60M-02-117
Hazard Warning Switch
Push in the hazard warning switch to acti-vate the hazard warning lights. All turn sig-nal lights and both turn signal indicators willflash simultaneously. To turn off the lights,
push the switch again.Use the hazard warning lights to warn othertraffic during emergency parking or whenyour vehicle could otherwise become atraffic hazard.
Windshield Wiper and Washer Lever
wwwww WARNING
60M-02-118
To avoid possible injury, do not oper-ate controls by reaching through thesteering wheel.
Windshield Wipers
Wiper and Washer OperationWhen the ignition switch is in the “ON”position, you can use the wiper/washer leveror switch (if equipped).
60M-02-119
To turn the windshield wipers on, move thelever down to one of the three operatingpositions. In the “INT” position, the wipersoperate intermittently. The “INT” position isvery convenient for driving in mist or lightrain. In the “LO” position, the wipers oper-ate at a steady low speed. In the “HI” posi-tion, the wipers operate at a steady highspeed. To turn off the wipers, move thelever back to the “OFF” position.
Move the lever up and hold it to the “MIST”position, the windshield wipers will turn oncontinuously at low speed.
2-40
BEFORE DRIVING
EXAMPLE
56
76G-74E
To spray windshield washer fluid, pull thelever toward you. The windshield wipers willautomatically turn on at low speed if theyare not already on and the “INT” positionis equipped.
Windshield Washer
60M-02-120
wwwww WARNING• To prevent windshield icing in cold
weather, turn on the defroster toheat the windshield before and dur-ing windshield washer use.
• Do not use radiator antifreeze in thewindshield washer reservoir. It canseverely impair visibility whensprayed on the windshield, and canalso damage your vehicle’s paint.
NOTICE
• Do not continue to hold in the leverwhen there is no windshield washerfluid being sprayed or the washermotor can be damaged.
• Do not attempt to remove dirt froma dry windshield with the wipers oryou can damage the windshield andthe wiper blades. Always wet thewindshield with washer fluid beforeoperating the wipers.
• Clear ice or packed snow from thewiper blades before using the wip-ers.
• Check the washer fluid level regu-larly. Check it often when theweather is bad.
• Only fill the washer fluid reservoir3/4 full during cold weather to allowroom for expansion if the tempera-ture falls low enough to freeze thesolution.
To help prevent damage to the wind-shield wiper and washer systemcomponents, you should take the fol-lowing precautions:
VV VVV
VVVV V
To turn the rear wiper on, twist the rear wiperswitch on the end of the lever forward to the“ON” position. To turn the rear wiper off, twistthe switch rearward to the “OFF” position.
To spray window washer fluid, twist theswitch rearward from the “OFF” position, ortwist the switch forward from the “ON” posi-tion. The rear wiper will turn on automati-cally while spraying the window washer fluid.
Rear Window Wiper/Washer Switch(if equipped)
60M-02-121
Clear ice or snow from the rear win-dow and rear wiper blade before usingthe rear wiper. Accumulated ice orsnow could prevent the wiper bladefrom moving, causing damage to thewiper motor.
NOTICE
60M-02-122
Tilt Steering Lock Lever
2-41
BEFORE DRIVING
EXAMPLENOTICE
57
76G-74E
(1) LOCK(2) UNLOCK
The lock lever is located under the steeringcolumn. To adjust the steering wheel height:
1) Push down the lock lever to unlock thesteering column.
2) Adjust the steering wheel to the desiredheight and lock the steering column bypulling up the lock lever.
3) Try moving the steering wheel up anddown to make sure it is securely lockedin position.
wwwww WARNINGNever attempt to adjust the steeringwheel while the vehicle is moving oryou could lose control of the vehicle.
60M-02-123
Heated Rear Window Switch(if equipped)
Horn
EXAMPLE
Press the horn button of the steering wheelto sound the horn. The horn will sound withthe ignition switch in any position.
60M-02-124
When the rear window is misted, push thisswitch (1) to clear the window.An indicator light will be lit when the defog-ger is on. The defogger will work only whenthe engine is running. To turn off thedefogger, push the switch (1) again.
NOTICEThe heated rear window uses a largeamount of electricity. Be sure to turnoff after the window has becomeclear.
NOTE:• The defogger will work only when the
engine is running.• The defogger will automatically turn off
after the defogger remains on for 15minutes to prevent discharging of thebattery.
2-42
BEFORE DRIVING
58
76G-74E
MEMO
2-43
BEFORE DRIVING
59
76G-74E
Exhaust Gas Warning ........................................................................................................ 3-1Daily Inspection Checklist ................................................................................................ 3-1Engine Oil Consumption ................................................................................................... 3-2Ignition Switch .................................................................................................................... 3-3Parking Brake Lever .......................................................................................................... 3-4Pedal ..................................................................................................................................... 3-5Starting the Engine ............................................................................................................ 3-5Using the Transmission .................................................................................................... 3-6Braking.................................................................................................................................. 3-7
OPERATING YOUR VEHICLE
3
60
76G-74E
60M-03-001
Exhaust Gas Warning
wwwww WARNINGAvoid breathing exhaust gases.Exhaust gases contain carbon mon-oxide, a potentially lethal gas that iscolorless and odorless. Since carbonmonoxide is difficult to detect byitself, be sure to take the followingprecautions to help prevent carbonmonoxide from entering your vehicle.• Do not leave the engine running in
garages or other confined areas.• Do not park with the engine running
for a long period of time, even in anopen area. If it is necessary to sitfor a short time in a parked vehiclewith the engine running, make sure
the air intake selector is set to“FRESH AIR” and the blower is athigh speed.
• Avoid operating the vehicle with thetailgate or trunk open. If it isnecessary to operate the vehiclewith the tailgate or trunk open,make sure the sunroof (if equipped)and all windows are closed, and theblower is at high speed with the airintake selector set to “FRESH AIR”.
• To allow proper operation of yourvehicle’s ventilation system, keepthe air inlet grille in front of thewindshield clear of snow, leaves orother obstructions at all times.
• Keep the exhaust tailpipe area clearof snow and other material to helpreduce the buildup of exhaust gasesunder the vehicle. This isparticularly important when parkedin blizzard conditions.
• Have the exhaust system inspectedperiodically for damage and leaks.Any damage or leaks should berepaired immediately.
VV VVV
wwwww WARNING
VVVV V
Daily Inspection ChecklistBefore Driving
60M-03-002
1) Make sure that windows, mirrors, lightsand reflectors are clean and unob-structed.
2) Visually check the tyres for the followingpoints:
– the depth of the tread groove– abnormal wear, cracks and damage– loose wheel nuts– existence of foreign material such as
nails, stones, etc.Refer to “Tyres” in “INSPECTION ANDMAINTENANCE” section for details.3) Look for fluid and oil leaks.
NOTE:It is normal for water to drip from the airconditioning system after use.
3-1
OPERATING YOUR VEHICLE
61
76G-74E
4) Make sure the hood is fully closed andlatched.
5) Check the headlights, turn signal lights,brake lights and horn for proper opera-tion.
6) Adjust the seat and head restraint (ifequipped).
7) Check the brake pedal and the parkingbrake lever.
8) Adjust the mirrors.9) Make sure that you and all passengers
have properly fastened your seat belts.10)Make sure that all warning lights come
on as the key is turned to the “ON” posi-tion.
11)Check all gauges.12)Make sure that the BRAKE SYSTEM
WARNING light turns off when theparking brake is released.
Once a week, or each time you fill your fueltank, perform the following under-hoodchecks:
1) Engine oil level2) Coolant level3) Brake fluid level4) Battery solution level5) Windshield washer fluid level6) Hood latch operation
Pull the hood release handle inside thevehicle. Make sure that you cannot openthe hood all the way without releasingthe secondary latch. Be sure to close
the hood securely after checking forproper latch operation. See the item “Alllatches, hinges and locks” of “CHASSISAND BODY” in the “PeriodicMaintenance Schedule” in the“INSPECTION AND MAINTENANCE”section for lubrication schedule.
wwwww WARNINGMake sure the hood is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.
Once a month, or each time you fill yourfuel tank, check the tyre pressure using atyre pressure gauge. Also check the tyrepressure of the spare tyre.
Engine Oil ConsumptionIt is normal for the engine to consume someengine oil during normal vehicle operation.
The amount of engine oil consumeddepends on the viscosity of the oil, thequality of the oil and the conditions thevehicle is driven under.More oil is consumed during high-speeddriving and when there is frequent acceler-ation and deceleration. Under high loads,your engine also will consume more oil.A new engine also consumes more oil,since its pistons, piston rings and cylinder
walls have not yet become conditioned. Newengines reach the normal level of oilconsumption only after approximately 5000km (3000 miles) driving.
Oil consumption:Max. 1.0 L per 1000 km(1 Qt. per 600 miles)
When judging the amount of oil consump-tion, note that the oil may become dilutedand make it difficult to accurately judge thetrue oil level.As an example, if a vehicle is used forrepeated short trips, and consumes a nor-mal amount of oil, the dipstick may notshow any drop in the oil level at all, evenafter 1000 km (600 miles) or more of driv-ing. This is because the oil is graduallybecoming diluted with fuel or moisture,making it appear that the oil level has notchanged.You should also be aware that the dilutingingredients evaporate out when the vehicleis subsequently driven at high speeds, suchas on an expressway, making it appear thatoil is excessively consumed after high-speeddriving.
3-2
OPERATING YOUR VEHICLE
62
76G-74E
Ignition Switch
60M-03-003
wwwww WARNINGTo avoid possible injury, do not oper-ate controls by reaching through thesteering wheel.
60M-03-004
EXAMPLE
The ignition switch has the following fourpositions:
LOCKThis is the normal parking position. It is theonly position in which the key can beremoved.
• Manual transmission vehiclesYou must push in the key to turn it to the“LOCK” position. It locks the ignition, andprevents normal use of the steering wheelafter the key is removed.
To release the steering lock, insert the keyand turn it clockwise to one of the otherpositions. If you have trouble turning the keyto unlock the steering, try turning thesteering wheel slightly to the right or leftwhile turning the key.
ACCAccessories such as the radio can operate,but the engine is off.
ONThis is the normal operating position. Allelectrical systems are on.
60M-03-005
STARTThis is the position for starting the engineusing the starter motor. The key should bereleased from this position as soon as theengine starts.
Ignition key reminderA buzzer sounds intermittently to remindyou to remove the ignition key if it is in theignition switch when the driver’s door isopened.
60M-03-006
wwwww WARNING• Never return the ignition switch to
the “LOCK” position and remove theignition key while the vehicle ismoving. The steering wheel will lockand you will not be able to steer thevehicle. VV VVV
3-3
OPERATING YOUR VEHICLE
63
76G-74E
wwwww WARNINGVVVV V
• Always return the ignition switch tothe “LOCK” position and remove theignition key when leaving thevehicle even if only for a short time.Also do not leave children alone ina parked vehicle. Unattended chil-dren could cause accidental move-ment of the vehicle or could tamperwith power windows. They alsocould suffer from heat stroke inwarm or hot weather. These couldresult in severe injury or evendeath.
NOTICE• Do not use the starter motor for
more than 15 seconds at a time. Ifthe engine does not start, wait 15seconds before trying again. If theengine does not start after severalattempts, check the fuel and ignitionsystems or consult your MARUTISUZUKI dealer.
• Do not leave the ignition switch inthe “ON” position if the engine isnot running as the battery will dis-charge.
Parking Brake Lever
(1) To set(2) To release(3) To release
The parking brake lever is located betweenthe seats. To set the parking brake, holdthe brake pedal down and pull the parkingbrake lever all the way up. To release theparking brake, hold the brake pedal down,pull up slightly on the parking brake lever,push the button on the end of the lever withyour thumb, and lower the lever to itsoriginal position.
EXAMPLE
60M-03-007
• Never drive your vehicle with theparking brake on: rear brake effec-tiveness can be reduced from over-heating, brake life may beshortened, or permanent brakedamage may result.
• If the parking brake does not holdthe vehicle securely or does notfully release, have your vehicleinspected immediately by an autho-rized MARUTI SUZUKI dealer.
wwwww WARNING
wwwww WARNINGAlways set the parking brake fullybefore leaving your vehicle or it maymove, causing injury or damage.When parking, make sure the gearshiftlever is in 1st gear or “R” (Reverse).Remember, even though the trans-mission is in gear, you must set theparking brake fully.
wwwww WARNINGWhen parking the vehicle in extremelycold weather, the following procedureshould be used:1)Set the parking brake.2)Turn off the engine, then shift into
reverse or first gear.3)Get out of the vehicle and put
chocks under the wheels.4)Release the parking brake.
When you return to your vehicle,you must remember to first set theparking brake, then remove thewheel chocks.
Parking Brake Reminder BuzzerA buzzer sounds intermittently to remindyou to release the parking brake if you drivethe vehicle without releasing the parkingbrake. Make sure that the parking brake isfully released and the brake system warninglight turns off.
3-4
OPERATING YOUR VEHICLE
64
76G-74E
Pedal
60M-03-008
EXAMPLE
Clutch Pedal (1)The clutch pedal is used to disengage thedrive to the wheels when starting theengine, stopping, or shifting the gearshiftlever. Depressing the pedal disengages theclutch.
wwwww WARNINGDo not drive with your foot resting onthe clutch pedal. It could result inexcessive clutch wear, clutch damage,or unexpected loss of engine braking.
Brake Pedal (2)Your MARUTI SUZUKI vehicle is equippedwith front disc brakes and rear drum brakes.Depressing the brake pedal applies bothsets of brakes.
You may hear occasional brake squealwhen you apply the brakes. This is a nor-mal condition caused by environmentalfactors such as cold, wet, snow, etc.
wwwww WARNINGIf brake squeal is excessive and occurseach time the brakes are applied, youshould have the brakes checked byyour MARUTI SUZUKI dealer.
wwwww WARNINGDo not “ride” the brakes by applyingthem continuously or resting your footon the pedal. This will result inoverheating of the brakes which couldcause unpredictable braking action,longer stopping distances, orpermanent brake damage.
Accelerator Pedal (3)This pedal controls the speed of the engine.Depressing the accelerator pedal increasespower output and speed.
Starting the Engine
Before Starting the Engine
60M-03-009
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress theclutch pedal all the way to the floor. Holdthe clutch pedal while starting theengine.
Make sure that the parking brake isset fully and the transmission is inNeutral before attempting to start theengine.
wwwww WARNING
Starting a Cold and Warm Engine(For Petrol Engine Model)
With your foot off the accelerator pedal,crank the engine by turning the ignition keyto “START”. Release the key when theengine starts.
NOTICE• Stop turning the starter immediately
after the engine has started or thestarter system can be damaged.
• Do not crank the engine for morethan 15 seconds at a time. If theengine doesn’t start on the first try,wait about 15 seconds before tryingagain.
If the engine does not start after 15 sec-onds of cranking, wait about 15 seconds,then press down the accelerator pedal to 1/
3-5
OPERATING YOUR VEHICLE
65
76G-74E
3 of its travel and try cranking the engineagain. Release the key and acceleratorpedal when the engine starts.
If the engine still does not start, try holdingthe accelerator pedal all the way to the floorwhile cranking. This should clear the engineif it is flooded.
(For Diesel Engine Model)
Cold engineTurn the ignition switch to the “ON” posi-tion and wait until the glow plug indicatorgoes out if it comes on. Crank the engineby turning the ignition key to “START”.Release the key when the engine starts.
NOTICE• Stop turning the starter immediately
after the engine has started or thestarter system can be damaged.
• Do not crank the engine for morethan 15 seconds at a time. If theengine doesn’t start on the first try,wait about 15 seconds before tryingagain.
Warm engineCrank the engine by turning the ignition keyto “START”. Release the key when theengine starts.
Caution when stopping the engine withturbochargerWhen stopping the engine after climbing orhigh speed driving, let the engine idle forabout one minute or more (if it is not pro-hibited) to cool down the turbocharger andengine oil. This is to prevent the engine oilfrom over-deteriorating. Deteriorated engineoil will damage the bearings of theturbocharger.
Restarting diesel engine after fuel-emptystopThe engine stops and the malfunction indi-cator light comes on if the engine feels fuelemptiness. To restart the engine, stop thevehicles, hold the ignition key in “ON” posi-tion for 5–10 seconds to feed fuel, thenperform above engine starting procedure.Have the indicator light turned off by yourMARUTI SUZUKI dealer.
in the engine’s sound, slowly press theaccelerator while continuing to graduallyrelease the clutch.
ShiftingAll forward gears are synchronized, whichprovides for quiet and easy shifting. Alwaysdepress the clutch pedal all the way to thefloor before shifting gears. Keep the enginespeed does not rise into the red zone ofthe tachometer.
Downshifting maximum allowablespeeds
For Petrol engine
Using the Transmission
60M-03-010
Starting offTo start off, depress the clutch pedal all theway to the floor and shift into 1st gear. Afterreleasing the parking brake, graduallyrelease the clutch. When you hear a change
Downshifting Km/h (mph)
2nd to 1st 35 (22)3rd to 2nd 70 (43)
4th to 3rd 105 (65)5th to 4th 140 (87)*
For Diesel engineDownshifting Km/h (mph)
2nd to 1st 30 (19)3rd to 2nd 60 (37)
4th to 3rd 95 (59)5th to 4th 135 (84)*
*NOTE:You may not accelerate to the maximumallowable speed because of the driving sit-uation and/or the vehicle condition.
3-6
OPERATING YOUR VEHICLE
EXAMPLE
66
76G-74E
NOTICEWhen downshifting to a lower gear,make sure not to downshift at thespeed faster than the maximumallowable speeds, or severe enginedamage can result.
wwwww WARNING• Reduce your speed and downshift
to a lower gear before going downa long or steep hill. A lower gearwill allow the engine to providebraking. Avoid riding the brakes orthey may overheat, resulting inbrake failure.
• When driving on slippery roads, besure to slow down before down-shifting. Excessive and/or suddenchanges in engine speed may causeloss of traction, which could causeyou to lose control.
NOTICEMake sure that the vehicle is com-pletely stationary before you shift intoreverse.
NOTICE• To help avoid clutch damage, do not
use the clutch pedal as a footrestwhile driving or use the clutch tokeep the vehicle stationary on aslope. Depress the clutch fully whenshifting.
• When shifting or starting off, do notrace the engine. Racing the enginecan shorten engine life and causenegative effect to smooth shifting.
Braking
60M-03-011
The distance needed to bring any vehicleto a halt increases with the speed of thevehicle. The braking distance needed, forexample, at 60 km/h (37 mph) will beapproximately 4 times greater than the
braking distance needed at 30 km/h (19mph). Start to brake the vehicle when thereis plenty of distance between your vehicleand the stopping point, and slow downgradually.
wwwww WARNINGIf water gets into the brake drums,brake performance may become poorand unpredictable. After drivingthrough water or washing the under-side of the vehicle, test the brakeswhile driving at a slow speed to seeif they have maintained their normaleffectiveness. If the brakes are lesseffective than normal, dry them byrepeatedly applying the brakes whiledriving slowly until the brakes haveregained their normal effectiveness.
Power-Assisted BrakesYour vehicle has power-assisted brakes. Ifpower assistance is lost due to a stalledengine or other failures, the system is stillfully operational on reserve power and youcan bring the vehicle to a complete stop bypressing the brake pedal once and holdingit down. The reserve power is partly usedup when you depress the brake pedal andreduces each time the pedal is pressed.Apply smooth and even pressure to thepedal. Do not pump the pedal.
3-7
OPERATING YOUR VEHICLE
67
76G-74E
Even without reserve power in thebrake system, you can still stop thevehicle by pressing the brake pedalharder than normally required. How-ever, the stopping distance may belonger.
wwwww WARNING
Brake Assist System (if equipped)When you slam the brakes on, the brakeassist system judges as an emergency stopand provides more powerful braking for adriver who cannot hold down the brakepedal firmly.
NOTE:If you quickly and forcefully depress thebrakes, you may hear a clicking sound inthe brake pedal. This is normal and indi-cates that the brake assist system is acti-vated properly.
Anti-Lock Brake System (ABS)(if equipped)ABS will help you avoid skidding by elec-tronically controlling braking pressure. It willalso help you maintain steering control whenbraking on slippery surfaces or whenbraking hard.The ABS works automatically, so you do notneed any special braking technique. Justpush the brake pedal down without
pumping. The ABS will operate whenever itsenses that the wheels are locking up. Youmay feel the brake pedal moves a littlewhile the ABS is operating.
NOTE:The ABS will not work if vehicle speed isunder about 10 km/h (6mph).
wwwww WARNING• On some types of loose surfaces
(such as gravel, snow-coveredroads, etc.) the stopping distancerequired for an ABS-equipped vehi-cle may be slightly greater than fora comparable vehicle with a con-ventional brake system. With aconventional brake system, skiddingtyres are able to “plow” the gravelor snow layer, shortening thestopping distance. ABS minimizesthis resistance effect. Allow for extrastopping distance when driving onloose surfaces.
• On regular paved roads, some driv-ers may be able to obtain slightlyshorter stopping distances withconventional brake systems thanwith ABS.
• In both of the above conditions,ABS will still offer the advantage ofhelping you maintain directional
VV VVV
wwwww WARNING
control. However, remember thatABS will not compensate for badroad or weather conditions or poordriver judgment. Use good judgmentand do not drive faster thanconditions will safely allow.
VVVV V
60M-03-012
1) ABS warning light2) Brake system warning light
wwwww WARNING• If the ABS warning light (1) on the
instrument panel comes on andstays on while driving, there may bea problem with the ABS system.Ask your MARUTI SUZUKI dealer toinspect the ABS system immedi-ately. If the ABS system becomesinoperative, the brake system willfunction as an ordinary brakesystem that has no ABS. VV VVV
3-8
OPERATING YOUR VEHICLE
68
76G-74E
wwwww WARNING
• If the ABS warning light (1) and theBrake system warning light (2) onthe instrument panel simultaneouslystays on or comes on when driving,both anti-lock function and rearbrake force control function(proportioning valve function) of theABS system may have failed. If so,the rear wheels may easily skid orthe vehicle can even spin in theworst case when braking on aslippery road or when hard brakingeven on a dry paved road. Ask yourMARUTI SUZUKI dealer to inspectthe ABS system immediately. Drivecarefully, avoiding hard braking asmuch as possible.
VVVV V
How the ABS WorksA computer continuously monitors wheelspeed. The computer compares the changesin wheel speed when braking. If the wheelsslow suddenly, indicating a skiddingsituation, the computer will change brakingpressure several times each second toprevent the wheels from locking. When youstart your vehicle or when you accelerateafter a hard stop, you may hear amomentary motor or clicking noise as thesystem resets or checks itself.
wwwww WARNINGThe ABS may not work properly iftyres or wheels other than thosespecified in the owner’s manual areused. This is because the ABS worksby comparing changes in wheelspeed. When replacing tyres orwheels, use only the size and typespecified in this owner’s manual.
3-9
OPERATING YOUR VEHICLE
69
76G-74E
DRIVING TIPSRunning-in ............................................................................................................................ 4-1Catalytic Converter ............................................................................................................. 4-1Improving Fuel Economy .................................................................................................. 4-2Highway Driving .................................................................................................................. 4-3Driving on Hills ................................................................................................................... 4-3Driving on Slippery Roads ............................................................................................... 4-3 4
70
76G-74E
60M-04-001
wwwww WARNING• Wear Your Seat Belts at All Times.
Even though air bags are equippedat the front seating positions, thedriver and all passengers should beproperly restrained at all times,using the seat belts provided. Referto the “Seat Belts and ChildRestraint Systems” section forinstructions on proper use of theseat belts.
• Never drive while under the influ-ence of alcohol or other drugs.Alcohol and drugs can seriouslyimpair your ability to drive safely,greatly increasing the risk of injuryto yourself and others. You shouldalso avoid driving when you aretyred, sick, irritated, or under stress.
NOTICEThe future performance and reliabilityof the engine depends on the careand restraint exercised during its earlylife. It is especially important toobserve the following precautionsduring the initial 960 km (600 miles)of vehicle operation.• After starting, do not race the
engine. Warm it up gradually.• Avoid prolonged vehicle operation at
a constant speed. Moving parts willbreak in better if you vary yourspeed.
• Start off from a stop slowly. Avoidfull throttle starts.
• Avoid hard braking, especially dur-ing the first 320 km (200 miles) ofdriving.
• Do not drive slowly with the trans-mission in a high gear.
• Drive the vehicle at moderate enginespeeds.
• Do not tow a trailer during the first960 km (600 miles) of vehicle oper-ation.
Running-in Catalytic Converter
60M-04-002
EXAMPLE
The purpose of the catalytic converter is tominimize the amount of harmful pollutantsin your vehicle’s exhaust. Use of leaded fuelin vehicles equipped with catalyticconverters is prohibited, because leaddeactivates the pollutant-reducing compo-nents of the catalyst system.
The converter is designed to last the life ofthe vehicle under normal usage and whenunleaded fuel is used. No special mainte-nance is required on the converter. How-ever, it is very important to keep the engineproperly tuned. Engine misfiring, which canresult from an improperly tuned engine, maycause overheating of the catalyst. This mayresult in permanent heat damage to thecatalyst and other vehicle components.
4-1
DRIVIING TIPS
71
76G-74E
To avoid damaging catalyst or othervehicle damage:• Maintain the engine in the proper
operating condition.• In the event of an engine malfunc-
tion, particularly one involvingengine misfiring or other apparentloss of performance, have the vehi-cle serviced promptly.
• Do not turn off the engine or inter-rupt the ignition when the trans-mission is in gear and the vehicleis in motion.
• Do not try to start the engine bypushing or towing the vehicle, orcoasting down a hill.
• Do not idle the engine with anyspark plug wires disconnected orremoved, such as during diagnostictesting.
• Do not idle the vehicle for pro-longed periods if idling seems roughor there are other malfunctions.
• Do not allow the fuel tank to getnear the empty level.
• Avoid driving your vehicle at exces-sively high engine speed in oraround the red zone of the tachom-eter (if equipped).
NOTICE
60M-04-003
wwwww WARNINGBe careful in areas where you parkand drive; the catalytic converter andother exhaust components can getvery hot. As with any vehicle, do notpark or operate this vehicle in areaswhere combustible materials such asdry grass or leaves can come in con-tact with a hot exhaust system.
temperature gauge pointer comes up to the“C” position (if the idling is not prohibited).In this position, the engine is sufficientlywarm for starting off.
Avoid “fast” startsFast starts away from lights or stop signswill consume fuel unnecessarily and shortenengine life. Start off slowly.
Avoid unnecessary stopsAvoid unnecessary deceleration and stop-ping. Try to maintain a slow, steady speedwhenever possible. Slowing down and thenaccelerating again uses more fuel.
Keep a steady cruising speedKeep as constant a speed as road and traf-fic conditions will permit.
Improving Fuel EconomyThe following instructions will help youimprove fuel economy.
Avoid excessive idlingIf you are to wait for more than a minutewhile you are parked, stop the engine andstart it again later. When warming up a coldengine, allow the engine to idle until the
60M-04-004
Keep the air cleaner clean
EXAMPLE
If the air cleaner is clogged with dust, therewill be greater intake resistance, resultingin decreased power output and increasedfuel consumption.
Keep weight to a minimumThe heavier the load, the more fuel the
4-2
DRIVING TIPS
72
76G-74E
vehicle consumes. Take out any luggage orcargo when it is not necessary.
Keep tyre pressures correctUnderinflation of the tyres can waste fueldue to increased running resistance of thetyres. Keep your tyres inflated to the correctpressure shown on the label on the driver’sside door or the driver’s door lock pillar.
Highway DrivingWhen driving at highway speeds, payattention to the following:• Stopping distance progressively increases
with vehicle speed. Apply the brakes farenough ahead of the stopping point toallow for the extra stopping distance.
• On rainy days, “Hydroplaning” can occur.“Hydroplaning” is the loss of direct con-tact between the road surface and thevehicle’s tyres due to a water filmforming between them. Steering orbraking the vehicle while “Hydroplaning”can be very difficult, and loss of controlcan occur. Keep speed down when theroad surface is wet.
• At high speeds, the vehicle may beaffected by side winds. Therefore, reducespeed and be prepared for unexpectedbuffeting, which can occur at the exitsof tunnels, when passing by a cut of ahill, or when being overtaken by largevehicles, etc.
Driving on Hills
60M-04-005
• When climbing steep hills, the vehiclemay begin to slow down and show a lackof power. If this happens, you should shiftto a lower gear so that the engine willagain be operating in its normal powerrange. Shift rapidly to prevent the vehiclefrom losing momentum.
• When driving down a hill, the engineshould be used for braking by shifting tonext lower gear.
Try not to hold the brake pedal downtoo long or too often while goingdown a steep or long hill. This couldcause the brakes to overheat, result-ing in reduced braking efficiency.Failure to take this precaution couldresult in loss of vehicle control.
wwwww WARNING
NOTICEWhen descending a down hill, NEVERturn the ignition key to the “OFF”position. Emission control systemdamage may result.
Under wet road conditions you should driveat a lower speed than on dry roads due topossible slippage of tyres during braking.When driving on icy, snow-covered, ormuddy roads, reduce your speed and avoidsudden acceleration, abrupt braking, orsharp steering movements.
Tyre ChainsTyre chains should only be used if they areneeded to increase traction or are requiredby law. Make sure that the chains you useare the correct size for your vehicle’s tyres.Also make sure that there is enough clear-ance between the fenders and the chainsas installed on the tyres.
Install the chains on the front tyres tightly,according to the chain manufacturer’s
Driving on Slippery Roads
60M-04-006
4-3
DRIVIING TIPS
73
76G-74E
instructions. Retighten the chains afterdriving about 1.0 km (1/2 mile) if necessary.With the chains installed, drive slowly.
NOTICE• If you hear the chains hitting
against the vehicle body while driv-ing, stop and tighten them.
• If your vehicle is equipped with fullwheel caps, remove the wheel capsbefore installing the chains or thewheel caps can be damaged by thechain bands.
If Your Vehicle Gets StuckIf your vehicle gets stuck in snow, mud, orsand, follow the directions below:
1) Shift the transmission back and forthbetween a forward range (or first gearfor manual transmission) and reverse.This will create a rocking motion whichmay give you enough momentum to freethe vehicle. Press gently on theaccelerator to keep wheel spinning to aminimum wheel rpm. Remove your footfrom the accelerator while shifting.Do not race the engine. Excessive wheelspin will cause the tyres to dig deeper,making it more difficult to free the vehicle.
2) If your vehicle remains stuck after a fewminutes of rocking, get another vehicleto pull your vehicle out.
wwwww WARNINGDo not allow anyone to stand near thevehicle when you are rocking it, anddo not spin the wheels faster than anindicated 40 km/h (25 mph) on thespeedometer. Personal injury and/ orvehicle damage may result from spin-ning the wheels too fast.
NOTICEDo not continue rocking the vehiclefor more than a few minutes. Pro-longed rocking can cause engineoverheating or transmission damage.
60M-04-007
4-4
DRIVING TIPS
wwwww WARNINGIn addition to following the driving tipsin this section, it is important toobserve the following precautions.• Make sure your tyres are in good
condition and always maintain thespecified tyre pressure. Refer to“Tyres” in the “INSPECTION ANDMAINTENANCE” section for details.
• Do not use tyres other than thosespecified by MARUTI SUZUKI. Neveruse different sizes or types of tyreson the front and rear wheels. Forinformation regarding the specifiedtyres, refer to the Tyre Information
DRIVING ON WET ROADS
• When driving on wet roads, avoiddriving through large amount ofstanding water on the road. Largeamount of water entering the enginecompartment may cause damage tothe engine and or electricalcomponents.
• If stuck in deep water, do not starttill water level drops.
• Water is incompressible substance,water inside engine is harmful to theengine.
CAUTION
VV VVV
74
76G-74E
wwwww WARNINGVVVV V Label located on the driver’s door
lock pillar.• Never use oversized tyres or special
shock absorbers and springs to raise(jack up) your vehicle. This willchange the handling characteristics.Oversized tyres may also rub againstthe fender over bumps, causingvehicle damage or tyre failure.
• After driving through water, test thebrakes while driving at a slow speedto see if they have maintained theirnormal effectiveness. If the brakesare less effective than normal, drythem by repeatedly applying thebrakes while driving slowly until thebrakes have regained their normaleffectiveness.
Starting1. Adjust the driver’s seat for the proper
driving posture.
2. Adjust the rear view mirror so as toobtain the best possible rear view.
3. Before moving off, look forward and backto confirm safety.
4. Don’t start quickly, for it is dangerousand wastes fuel.
General driving1. Be sure to stop before the stop light and
stop sign. When moving into theintersection without any traffic lights orsigns, drive slowly to confirm safety.
2. Always follow other vehicles at a safedistance in order to prevent a rear-endcollision, should the vehicle ahead makea sudden stop.
3. Turn ON the turn signal at least 30meters before making a turn or changingthe lane so as not to be hit from behind.
4. Before entering a corner, decelerate toa safe speed. Don’t apply brakes duringcornering, or a cornering skid may occur.
5. When overtaking other vehicles, watchout for the oncoming vehicle andcarefully confirm the safety.
6. Don’t attempt zigzag driving which willhinder your control over the vehicle andcause an accident.
60M-04-008 60M-04-009
DO’S AND DON’TS FOR SAFEDRIVINGExercise care in handling your vehicle. Beconscious of not only your own safety butalso the safety of others on the road, andthus enjoy the best and most comfortabledriving experience.
This section contains basic rules for safedriving. Read it carefully for goodunderstanding of the content so that youcan enjoy safe and pleasant driving in yourMaruti Suzuki vehicle.4-5
DRIVIING TIPS
75
76G-74E
especially dangerous when the tyres areworn, for they allow a larger skid.Use foot brake in three stages(1) Warn the vehicle behind you(2) Gradually apply the brake.(3) Bring the vehicle to a halt.
3. When driving on a downhill, try not toapply the brake but use the enginebrake effectively. Overuse of thefootbrake may result in total brakefailure.
4. Avoid reckless high speed driving and tryto drive at a safe speed suitable for theroad conditions while maintaining aconstant speed.
5. The higher the speed, the narrower thedriver’s visual range becomes. In sucha state, it is difficult to anticipate anyhazard and the driver feels muchfatigued.
6. Never do sharp handling during highspeed driving. You will lose your controlover your vehicle.
7. When overtaking or changing the lanewhile driving at a high speed, keep anample vehicle-to-vehicle distance.
Long distance driving1. Be sure to perform safety checks before
starting a trip.
2. Take rest at certain intervals to preventan accident which may occur when youare sleepy or tyred.
Braking1. Use the parking brake when parking
your vehicle and shift the gear shift leverinto the first gear or reverse gearposition for the sake of safety.
2. Don’t use handbraking unlessunavoidable. It causes the vehicle to skidand a rearend collision occur. It is
60M-04-010
60M-04-011 60M-04-012
4-6
DRIVING TIPS
76
76G-74E
Night time driving1. Drive more slowly at night than in the
daytime, for the visual range is restrictedat night.
2. Don’t overtake other vehicles at night.Darkness bothers your sense of speedand hinders your judgement on thevehicle-to-vehicle distance.
3. Don’t use the high headlight beamunless its use is inevitable. Its dazzlemay blitz the driver of the oncomingvehicle, thus causing an accident.
4. Always keep the window glasses clean.Don’t operate the windshield wiper whenthe windshield glass is dry or the wiperblade and glass may get damaged.
MARGIN FOR SAFETY
It is important to allow yourself a margin forsafety during driving so that you can copewith erroneous or unexpected driving ofother drivers. For that, observe thefollowing.
• Drive at a safe speed.• Maintain a sufficient distance between
your vehicle and the vehicle ahead.• Don’t force yourself to overtake other
vehicles.• Don’t make quick start, hard steering or
sudden stops.• Allow an ample time in the driving
schedule.• Observe traffic rules and regulations.
CONCLUSION
A perfect driver does not exist. Theendeavour of every motorist should be tostrive for perfection. Safety consciousnessnot only ensures your safety and the safetyof other road users, it also helps reduce thewear and tear on your vehicle, prolongs itslife, gives more mileage and ensures acomfortable driving experience.
Follow the do’s and don’ts listed, anddriving will never be the same again.
60M-04-013 60M-04-014
60M-04-015
4-7
DRIVIING TIPS
77
76G-74E
OTHER CONTROLS AND EQUIPMENTManual Heating and Air Conditioning System ............................................................. 5-1Radio Antenna ..................................................................................................................... 5-4Audio System (if equipped) ............................................................................................. 5-5Fuel Filler Cap .................................................................................................................. 5-32Engine Hood ...................................................................................................................... 5-33Sun Visor ........................................................................................................................... 5-33Interior Light Switch ........................................................................................................ 5-34Accessory Socket ............................................................................................................. 5-35AUX/USB Socket (if equipped) ...................................................................................... 5-35Assist Grips ....................................................................................................................... 5-35Glove Box .......................................................................................................................... 5-35Cup Holder and Storage Area ....................................................................................... 5-36Front Seat Back Pocket (if equipped) ......................................................................... 5-37Armrest (if equipped) ...................................................................................................... 5-37Floor Mats (if equipped) ................................................................................................. 5-37Luggage Box ..................................................................................................................... 5-38Frame Hooks ..................................................................................................................... 5-38
5
OTHER CONTROLS AND EQUIPMENT
78
76G-74E
Manual Heating and Air ConditioningSystem
Air Outlet
60M-05-001
1. Windshield defroster outlet2. Side defroster outlet3. Side outlet4. Center outlet5. Floor outlet
Side outlet
60M-05-002
Move the knob (1) vertically and the dial (2)horizontally, to adjust the direction of airflow
as desired. When “Open”, air comes outfrom the side outlets regardless of theairflow selector position.
Center outlet
60M-05-003
Move the knob (1) vertically or horizontallyto adjust the direction of airflow as desired.
Overhead rear air conditioning system(if equipped)
60M-05-004
To turn on the overhead rear air condi-tion-ing system, set the blower speed selector
of the manual heating and air conditioningsystem to a position other than “OFF” andset the rear blower switch (2) to a positionother than “OFF”. Move the knob (1) verti-cally or horizontally to adjust the directionof airflow as desired.
If you need cold air to come out, turn onthe air conditioning switch. Refer to “Airconditioning switch” in this section.
During operation of the air conditioner, youmay notice slight changes in engine speed.These changes are normal, the system isdesigned so that the compressor turns onor off to maintain the desired temperature.Less operation of the compressor results inbetter fuel economy.
Description of Controls
60M-05-005
5-1
OTHER CONTROLS AND EQUIPMET
EXAMPLE
EXAMPLE
79
76G-74E
Temperature selector (1)This is used to select the temperature byturning the selector.
Blower speed selector (2)This is used to turn on the blower and toselect blower speed by turning the selector.
Air flow selector (3)
60M-05-007
60M-05-006
This is used to select one of the functionsdescribed below.
Ventilation (a)
Temperature-controlled air comes out of thecenter and side air outlets.
Bi-level (b)
Heat & defrost (d)
60M-05-008
Temperature-controlled air comes out of thefloor outlets and cooler air comes out of thecenter and side outlets. When thetemperature selector (1) is in the fully COLDposition or fully HOT position, however, theair from the floor outlets and the air fromthe center and side outlets will be the sametemperature.
Heat (c)
60M-05-009
Temperature-controlled air comes out of thefloor outlets and the side outlets, alsocomes out of the windshield defroster out-lets and also comes slightly out of the sidedefroster outlets.
60M-05-010
Temperature-controlled air comes out of thefloor outlets, the windshield defroster outlets,the side defroster outlets and the sideoutlets.
Defrost (e)
60M-05-011
Temperature-controlled air comes out of thewindshield defroster outlets, the sidedefroster outlets and the side outlets.
Air intake selector (4)
60M-05-012
5-2
OTHER CONTROLS AND EQUIPMENT
80
76G-74E
This selector is used to select the followingmodes.
Fresh Air (f)When this mode is selected, the indicatorlight will go off and outside air is used.
Recirculated Air (g)When this mode is selected, the indicatorlight will come on, outside air is shut outand inside air is recirculated. This mode issuitable when driving through dusty or pol-luted air such as in a tunnel, or whenattempting to quickly cool down the interior.
“FRESH AIR” and “RECIRCULATED AIR”are switched alternately each time the airintake selector is pushed.
NOTE:If you select “RECIRCULATED AIR” for anextended period of time, the air in the vehi-cle can become contaminated. Therefore,you should occasionally select “FRESH AIR”.
Air conditioning switch (5)To turn on the air conditioning system, setthe blower speed selector to a position otherthan “OFF” and push in the “A/C” switch.With this “A/C” switch operation, a indicatorlight will come on when the air conditioningsystem is on. To turn off the air conditioningsystem, push the “A/C” switch again.
During operation of the air conditioner, you
may notice slight changes in engine speed.These changes are normal, the system isdesigned so that the compressor turns onor off to maintain the desired temperature.
Less operation of the compressor results inbetter fuel economy.
System Operating Instructions
Natural ventilationSelect “VENTILATION” and “FRESH AIR”,the temperature selector to the desiredtemperature position, and the blower speedselector to “OFF”. Fresh air will flow throughthe vehicle during driving.
Forced ventilationThe control settings are the same as fornatural ventilation except you set the blowerspeed selector to a position other than “OFF”.
Normal heating (using outside air)Select “HEAT” and “FRESH AIR”, the tem-perature selector to the desired temperatureposition and the blower speed selector tothe desired blower speed position. Settingthe blower speed selector to a higher blowerspeed position increases heating efficiency.
Quick heating (using recirculated air)The control settings are the same as fornormal heating except you select “RECIR-CULATED AIR”. If you use this heatingmethod for an extended period of time, theair in the vehicle can become contaminated
and the windows can become misty.Therefore, use this method only for quickheating and change to the normal heatingmethod as soon as possible.
Head cooled/Feet warmed heatingSelect “BI-LEVEL” and “FRESH AIR”, thetemperature selector to the desired tem-perature position, and the blower speedselector to the desired blower speed posi-tion. Unless the temperature selector is inthe fully COLD position or fully HOT posi-tion, the air that comes out of the centerand side outlets will be cooler than the airthat comes out of the floor outlets.
Normal coolingSet the air flow selector to “VENTILATION”,the temperature selector to the desiredtemperature position and the blower speedselector to the desired blower speed posi-tion, and turn on the “A/C” switch. Settingthe blower speed selector to a higher blowerspeed position increases cooling efficiency.
You can switch the air intake selector toeither “FRESH AIR” or “RECIRCULATEDAIR” as you desire. Choosing “RECIRCU-LATED AIR” increases cooling efficiency.
Quick cooling (using recirculated air)The control settings are the same as fornormal cooling except you select “RECIR-CULATED AIR” and the highest blowerspeed.
5-3
OTHER CONTROLS AND EQUIPMET
81
76G-74E
NOTE:
• If you select “RECIRCULATED AIR” foran extended period of time, the air in thevehicle can become contaminated.Therefore, you should occasionally select“FRESH AIR”.
• If your vehicle has been left in the sunwith the windows closed, it will coolfaster if you open the windows brieflywhile you operate the air conditioner withthe air intake selector at “FRESH AIR”and the blower at high speed.
DehumidifyingSet the air flow selector to a desired air flowselector position, the temperature selectorto the desired temperature position and theblower speed selector to the desired blowerspeed position. Also select “FRESH AIR”and turn on the “A/C” switch.
NOTE:Because the air conditioner dehumidifies theair, turning it on will help keep the windowsclear, even when blowing heated air usingthe “DEFROST” or “HEAT & DEFROST”functions.
NOTE:If you need maximum defrosting:• select “DEFROST” and “FRESH AIR”,• turn on the “A/C” switch,• set the blower speed selector to HIGH,• adjust the temperature selector to the
HOT end, and• adjust the side outlets so the air blows
on the side windows.
MaintenanceIf you do not use the air conditioner for along period, such as during winter, it maynot give the best performance when youstart using it again. To help maintain opti-mum performance and durability of your airconditioner, it needs to be run periodically.Operate the air conditioner at least once amonth for one minute with the engine idling.
60M-05-013
This circulates the refrigerant and oil andhelps protect the internal components.
If your air conditioner is equipped with airfilters, clean or replace them as specifiedin the “Maintenance Schedule” in the“INSPECTION AND MAINTENANCE” sec-tion. Have this job done by your MARUTISUZUKI dealer as the lower glove box mustbe lowered for this job.
NOTE:Your vehicle uses the air conditioningrefrigerant HFC-134a, commonly called “R-134a”. R-134a replaced R-12 around 1993for automotive applications. Other refrigerantsare available, including recycled R-12, butonly R-134a should be used in your vehicle.
NOTICEUsing the wrong refrigerant maydamage your air conditioning system.Use R-134a only. Do not mix or replacethe R-134a with other refrigerants.
Radio Antenna
60M-05-014
EXAMPLE
5-4
OTHER CONTROLS AND EQUIPMENT
EXAMPLE
82
76G-74E
The radio antenna on the roof is removable.To remove the antenna, turn it coun-terclockwise. To reinstall the antenna, turnit clockwise firmly by hand.
NOTICETo avoid damage to the radio antenna:Remove the antenna when using anautomatic car wash.• Remove the antenna when the
antenna hits anything such as a lowceiling in a parking garage or puttinga car cover over your vehicle.
Audio System (if equipped)
AM/FM CD PLAYER
60M-05-015
Safety Information
wwwww WARNINGIf you pay extended attention to oper-ating the audio system or viewing theaudio system display while driving, anaccident can occur. If you set thesound volume too loud, it could pre-vent you from being aware of roadand traffic conditions.• Keep your eyes on the road and
your mind on the drive. Avoid pay-ing extended attention to operatingthe audio system or viewing theaudio system display.
• Familiarize yourself with the audiosystem controls and operation ofthe audio system before driving.
• Preset your favorite radio stationsbefore driving so that you canquickly tune to them using the pre-sets.
• Set the sound volume to a level thatwill allow you to continue to beaware of road and traffic conditionswhile driving.
Notes on DiscsPrecautions• When the inside of the vehicle is very
cold and the player is used soon afterswitching on the heater, condensationmay form on the disc or the optical parts
of the player and proper playback maynot be possible. If condensation forms onthe disc, wipe it off with a soft cloth. Ifcondensation forms on the optical partsof the player, do not use the player forabout one hour. This will allow thecondensation to disappear normally.
• Driving on extremely bumpy roads whichcause severe vibrations may causesound to skip.
• This unit uses a precision mechanism.Even in the event that trouble arises,never open the case, disassemble theunit, or lubricate the rotating parts.Please bring the unit to an authorizedMARUTI SUZUKI dealer.
Cautions on Handling
60M-05-016
This unit has been designed specifically forplayback of compact discs bearing mark (A)shown above.No other discs can be played.
5-5
OTHER CONTROLS AND EQUIPMET
83
76G-74E
60M-05-017
New discs may have some roughnessaround the edges. The unit may not workor the sound may skip if such discs areused. Use a ball-point pen (B), etc. toremove the roughness (C) from the edgesof the disc before inserting it into the unit.
To remove the compact disc from its stor-age case, press down on the center of thecase and lift the disc out, holding it care-fully by the edges.
Always handle the compact disc by theedges.Never touch the surface.
60M-05-018
To remove fingermarks and dust, use a softcloth, and wipe in a straight line from thecenter of the compact disc to the cir-cumference.
60M-05-019
60M-05-020
Never stick labels on the surface of thecompact disc or write on the surface witha pencil or pen.
60M-05-021
Do not use any solvents such as commer-cially available cleaners, anti-static spray, orthinner to clean compact discs.
60M-05-022
Do not use compact discs that have largescratches, are misshaped, or cracked, etc.Use of such discs will cause damage orprevent the system from operating properly.
60M-05-023
Do not expose compact discs to direct sun-light or any heat source.NOTE:• Do not use commercially available CD
protection sheets or discs equipped withstabilizers, etc.These may get caught in the internalmechanism and damage the disc.
• It may be impossible to play CD-R discswith this unit due to the recording condi-tions.
• CD-RW discs cannot be played with thisunit.
5-6
OTHER CONTROLS AND EQUIPMENT
84
76G-74E
wwwww WARNINGThis is a class I laser product. Use ofcontrols or adjustments or perfor-mance of procedures other than thosespecified herein may result inhazardous radiation exposure.Do not open covers and do notattempt to repair this unit by yourself.Refer servicing to qualified personnel.
Basic Operations
(1) VOL PUSH POWER knob(2) TUNE FOLDER PUSH SOUND knob(3) MUTE button
60M-05-024
Adjusting the volumeTurn the VOL PUSH POWER knob (1).Turning it clockwise increases the volume;turning it counterclockwise decreases thevolume.
NOTE:While driving, adjust the volume to an extentthat sound and/or noise coming from outsidethe vehicle can be heard.
MutePress the MUTE button (3) to mute thesound. To cancel the mute, press the MUTEbutton (3) again.
Adjusting bass/treble/balance /fader1) Press the TUNE FOLDER PUSH
SOUND knob (2).Each time the knob is pressed, soundadjustment will change as follows:
Turning power on/offPress the VOL PUSH POWER knob (1).The unit starts in the function mode it wasin when the power was turned off last.
60M-05-025
2) Turn the TUNE FOLDER PUSH SOUNDknob (2) to adjust the sound.
Adjusting the AVC (Auto volume control)The Auto Volume Control (AVC) functionautomatically adjusts (increases/ decreases)the sound volume in accordance withvehicle speed. The AVC control is providedwith three selectable levels (LEVEL OFF, 1,2, 3). The range of volume adjustmentincreases together with the LEVEL number.1) Press the TUNE FOLDER PUSH
SOUND knob (2) until the AVC adjust-ment mode is selected.
2) Turn the TUNE FOLDER PUSH SOUNDknob (2) to select the desired AVCadjustment level. (Initial setting: LEVEL 2)
Preset-EQPreset-EQ calls up various sound types inaccordance with the listening music type.1) Press the TUNE FOLDER PUSH
SOUND knob (2) several times until“PRESET-EQ” appears.
2) Turn the TUNE FOLDER PUSH SOUNDknob (2).Each time the knob is turned, preset EQmode will change as follows:
5-7
OTHER CONTROLS AND EQUIPMET
85
76G-74E
60M-05-026
Listening to the Radio
60M-05-027
Display
60M-05-028
(1) FM/AM button(2) SCAN button(3) Up button(4) Down button(5) TUNE FOLDER PUSH SOUND knob(6) Preset buttons ([1] to [6])(7) AST button
(A) Band(B) Frequency
Selecting the reception bandPress the FM/AM button (1).Each time the button is pressed, the recep-tion band will change as follows:
60M-05-029
Seek tuningPress the seek Up button (3) or the seekDown button (4).
The unit stops searching for a station at afrequency where a broadcast station isavailable.
Manual tuningTurn the TUNE FOLDER PUSH SOUNDknob (5).The frequency being received is displayed.
ScanPress the SCAN button (2).It starts seeking upward (higher frequency),and pauses for 5 seconds to receive theband, and sequentially repeats seeking andplay.
NOTE:• When the SCAN button (2) is pressed
while pausing for receiving, it cancels thescan operation and continuously receivesthe station.
• When the SCAN button (2) is pressedwhile searching, it cancels the scanoperation and stops at next receivablestation.
Preset memory1) Select the desired station.2) Hold down a desired button ([1] to [6])
of the Preset buttons (6) to which youwant to store the station for 2 secondsor longer.
5-8
OTHER CONTROLS AND EQUIPMENT
86
76G-74E
Auto storeHold down the AST button (7) for 2 sec-onds or longer.Six stations in good reception will automat-ically be stored to the Preset buttons (5) inorder, starting from a station whose fre-quency is the lowest.
NOTE:• Auto store can be released by pressing
AST button (7) while auto store is underway.
• When the auto store is performed, thestation previously stored in the memoryat the position is overwritten.
• When there are fewer than 6 stationsthat can be stored even if 1 round ofauto store operation is performed, nostation will be stored at the remainingPreset buttons (6).
• 6 stations can be preset for FM1 andFM2 in common, and 6 stations for AMin auto store mode.
Radio ReceptionRadio reception can be affected by envi-ronment, atmospheric conditions, or radiosignal’s power and distance from the sta-tion. Nearby mountains and buildings mayinterfere or deflect radio reception, causingpoor reception. Poor reception or radio staticcan also be caused by electric current fromoverhead wires or high voltage power lines.
Auto store mode on/offPress the AST button (7).Each time the button is pressed, the modeis switched as follows:
60M-05-030
Listening to a CD
60M-05-031
Display
(1) Insertion slot(2) Eject button(3) CD button(4) Up button(5) Down button(6) RPT button(7) RDM button(8) DISP button(9) SCAN button
(A) Track number(B) Play time
NOTE:This product does not support 8 cm CD(sometimes called as “mini single CD”, “3-inch CD”, “CD3”, etc.).
60M-05-032
• CDs or CD-ROMs carrying no mark (A)cannot be used.
• Some discs recorded in CD-R/CD-RWformat may sometimes be impossible touse.
60M-05-033
5-9
OTHER CONTROLS AND EQUIPMET
87
76G-74E
60M-05-034
• A CD is to be inserted with its label sideup.
• When there is a CD already in the unit,it is impossible to insert another CDwithout ejecting the CD in the unit. Donot use force to insert a CD into the CDinsertion slot.
NOTICE• Never insert your finger or hand into
the CD insertion slot. Never insertforeign objects.
• Never insert a CD with glue comingout from adhesive tape or a rentalCD label or with a trace indicatingthat adhesive tape or a rental CDlabel has been removed. This maycause the CD not to eject or resultin a malfunction.
Selecting a CD modePress the CD button (3).Each time the button is pressed, the modewill change as follows:
60M-05-035
Loading a CDInsert a CD in the Insertion slot (1).When a CD is loaded, play starts.
Ejecting a CDPress the Eject button (2).When the ignition mode is “LOCK”, the CDremained ejected for around 15 seconds orlonger will automatically be drawn inside theunit. (Auto reload function)The backup eject function:This function allows you to eject a CD bypressing the Eject button (2) even when theignition mode is off.
NOTICEIf you forcefully try to push an ejectedCD inside the unit before auto reload-ing, the disc surface might bescratched.When reloading a CD, remove it fromthe unit completely before reloading.
When a CD is already inside the unit, pressthe CD button (3) to start playback.
Listening to a CDWhen a CD is inserted, playback will auto-matically start.
Selecting a track• Press the Up button (4) to listen to the
next track.• Press the Down button (5) twice to lis-
ten to the previous track.• When the Down button (5) is pressed
once, the track currently being playedwill start from the beginning again.
Fast forwarding/Rewinding a track• Hold down the Up button (4) to fast for-
ward the track.• Hold down the Down button (5) to fast
rewind the track.
Track scan playPress the SCAN button (9).The first 10 seconds of each track in thedisc is played in sequence.
NOTE:• When the scan play is done for one
round, the normal playback starts.• To cancel the scan play, press the
SCAN button (9) again.
Random playbackPress the RDM button (7).Each time the button is pressed, the modewill change as follows:
5-10
OTHER CONTROLS AND EQUIPMENT
88
76G-74E
60M-05-036
• TRACK RANDOMThe random indicator “RDM” will light.The tracks in the loaded disc will beplayed in random order.
Repeat playbackPress the RPT button (6).Each time the button is pressed, the modewill change as follows:
60M-05-037
• TRACK REPEATThe repeat indicator “RPT” will light.The track currently being played will beplayed repeatedly.
Display changePress the DISP button (8).Each time the button is pressed, display willchange as follows:
NOTE:• “NO TITLE” will be displayed when there
is no text information in the disccurrently being played.
• If text data contains more than 12 char-acters, the “>” mark will appear at theright end. Holding down the DISP button(8) for 1 second or longer can displaythe next page.
60M-05-038
Display
Listening to an MP3/WMA Disc
60M-05-039
60M-05-040
(1) TUNE FOLDER PUSH SOUND knob(2) Up button(3) Down button(4) RPT button(5) RDM button(6) DISP button(7) SCAN button
(A) Folder number(B) Track number(C)Play time(D)MP3/WMA indicator
Selecting a folderTurn the TUNE FOLDER PUSH SOUNDknob (1) to select a folder.
Selecting a track• Press the Up button (2) to listen to the
next track.• Press the Down button (3) twice to lis-
ten to the previous track.• When the Down button (3) is pressed
once, the track currently being playedwill start from the beginning again.
5-11
OTHER CONTROLS AND EQUIPMET
89
76G-74E
Fast forwarding/Rewinding a track• Hold down the Up button (2) to fast for-
ward the track.• Hold down the Down button (3) to fast
rewind the track.
Scan play• FILE SCAN
Press the SCAN button (7).The first 10 seconds of each file in thecurrently playing folder is played insequence.
• FOLDER SCANPress the SCAN button (7) for 1 sec-ond or longer.The first 10 seconds of the first file ineach folder stored in the disc is playedin sequence.
NOTE:• When the scan play is done for one
round, the normal playback starts.• To cancel the scan play, press the
SCAN button (7) again.
Random playbackPress the RDM button (5).Each time the button is pressed, the modewill change as follows:
• FOLDER RANDOMThe random indicator “RDM.F” will light.The tracks in the current folder will beplayed in random order.
• ALL RANDOMThe random indicator “RDM” will light.The tracks in the loaded disc will beplayed in random order.
60M-05-041
NOTE:• “NO TITLE” will be displayed when there
is no text information in the disccurrently being played.
• If text data contains more than 12 char-acters, the “>” mark will appear at theright end. Holding down the DISP button(6) for 1 second or longer can displaythe next page.
Repeat playbackPress the RPT button (4).Each time the button is pressed, the modewill change as follows:
60M-05-042
• FILE REPEATThe repeat indicator “RPT” will light.The track currently being played will beplayed repeatedly.
• FOLDER REPEATThe repeat indicator “RPT.F” will light.All tracks in the currently selected folderwill be played repeatedly.
Display changePress the DISP button (6).Each time the button is pressed, display willchange as follows:
60M-05-043
5-12
OTHER CONTROLS AND EQUIPMENT
90
76G-74E
WMA• It is recommended to set the bit rate to
“64 kbps or more” and “fixed”.• Do not set the copy protect attribute on
the WMA file to enable this unit to play-back.
Notes on MP3/WMAWhat is MP3/WMA?MP3 (MPEG1/2 Audio Layer-III) and WMA(Windows MediaTM Audio) are the com-pression formats of digital audio. The formeris developed by MPEG (Motion PictureExperts Group), and the latter is developedby Microsoft Corporation.Using these compression formats, you canrecord contents of about 10 music CDs ona single CD media. (This figure refers todata recorded on a 650 MB CD-R or CD-RW at a fixed bit rate of 128 kbps and asampling frequency of 44.1 kHz.)
Points to remember when making MP3/WMA filesCommon• High bit rate and high sampling fre-
quency are recommended for highquality sounds.
• Selecting VBR (Variable Bit Rate) is notrecommended. Selecting VBR maycause display of incorrect playing timeand jumpiness of playback.
• Playback sound quality varies dependingon the encoding environment. Fordetails, refer to the user manual of theencoding software and the writing soft-ware in use.
MP3• It is recommended to set the bit rate to
“128 kbps or more” and “fixed”.
NOTICENever assign the “.mp3”, or “.wma”file name extension to a file if it is notin the MP3/WMA format file. Failure toobserve this may result in damage tothe speaker due to noise production.
• You may encounter a trouble in playingMP3/WMA files or displaying informationof MP3/WMA files depending on thewriting software or CD recorder in use.
• This unit does not have a play list func-tion.
• It is recommended to write discs in Disc-at-Once mode even though Multi-sessionmode is supported.
Compression formatsMP3• Bit rate:
MPEG1 Audio Layer III: 64 k -320 kbpsMPEG2 Audio Layer III: 64 k - 160 kbps
• Sampling frequency:MPEG1 Audio Layer III: 32 k/44.1 k/48kHzMPEG2 Audio Layer III: 16 k/22.05 k/24kHz
WMA (Ver.7, Ver.8)• Bit rate: CBR 48 k -192 kbps• Sampling frequency: 32 k/44.1 k/48 kHz
Recording MP3/WMA files on a CD media• It is recommended not to write both CD-
DA files and MP3/WMA files on a disc.• If both CD-DA files and MP3/WMA files
are on the same disc, tracks may notbe played in the correct order or sometracks may not be played at all.
• When storing both MP3 data and WMAdata on the same disc, sort and placethem in different folders.
• Do not write files other than MP3/WMAfiles and unnecessary folders on a disc.
• MP3/WMA files should be named tomeet the standards and the file systemspecifications as shown below.
• The file extension “.mp3” or “.wma”should be assigned to files based ontheir format independently.
WMA (Ver. 9*)• Bit rate: CBR 48 k - 320 kbps• Sampling frequency: 32 k/44.1 k/48 kHz* WMA 9 Professional/LossLess/Voice are
not supported.
Supported file systemsISO 9660 Level 1/Level 2, Joliet, Romeo
5-13
OTHER CONTROLS AND EQUIPMET
91
76G-74E
Maximum number of files/folders• Maximum number of files: 512 (files +
folders)• Maximum number of files in a folder:
512• Maximum depth of tree structure: 8• Maximum number of folders: 255
(Root folder is included.)
Listening to files stored in a USBdevice
60M-05-044
Display
(1) USB button(2) TUNE FOLDER PUSH SOUND knob(3) Up button(4) Down button(5) RPT button(6) RDM button(7) DISP button(8) SCAN button
(A) Folder number(B) Track number(C)Play time(D)MP3/WMA indicator
60M-05-045
NOTICEDo not connect any USB device otherthan a USB memory or a USB audioplayer. Do not connect multiple USBdevices to the USB connector usinga USB hub, etc. Supplying power tomultiple USB devices from the con-nector could cause overheating andsmoking.
Selecting a USB device modePress the USB button (1).
Selecting a folderTurn the TUNE FOLDER PUSH SOUNDknob (2) to select the desired folder.
Selecting a track• Press the Up button (3) to listen to the
next track.
• Press the Down button (4) twice to lis-ten to the previous track.
• When the Down button (4) is pressedonce, the track currently being playedwill start from the beginning again.
Fast forwarding/Rewinding a track• Hold down the Up button (3) to fast for-
ward the track.• Hold down the Down button (4) to fast
rewind the track.
Scan play• FILE SCAN
Press the SCAN button (8).The first 10 seconds of each file in thecurrently playing folder is played insequence.
• FOLDER SCANPress the SCAN button (8) for 1 sec-ond or longer.The first 10 seconds of the first file ineach folder stored in the USB is playedin sequence.
NOTE:• When the scan play is done for one
round, the normal playback starts.• To cancel the scan play, press the
SCAN button (8) again.
5-14
OTHER CONTROLS AND EQUIPMENT
92
76G-74E
Random playbackPress the RDM button (6).Each time the button is pressed, the modewill change as follows:
60M-05-046
• FOLDER RANDOMThe random indicator “RDM.F” will light.The tracks in the currently selectedfolder will be played in random order.
• ALL RANDOMThe random indicator “RDM” will light.The tracks in the connected USB devicewill be played in random order.
Repeat playbackPress the RPT button (5).Each time the button is pressed, the modewill change as follows:
60M-05-047
The track currently being played will beplayed repeatedly.
• FOLDER REPEATThe repeat indicator “RPT.F” will light.All the tracks in the folder currentlyselected will be played repeatedly.
Display changePress the DISP button (7).Each time the button is pressed, display willchange as follows:
NOTE:• “NO TITLE” will be displayed when there
is no text information in the disccurrently being played.
• If text data contains more than 12 char-acters, the “>” mark will appear at theright end. Holding down the DISP button(7) for 1 second or longer can displaythe next page.
Notes on USB deviceCompatible USB devices• USB Mass Storage Class
For details as to whether your USBmemory/USB Audio is compatible withUSB Mass Storage Class, please con-tact the USB memory/USB Audio man-ufacturer.
• USB Standard Compatibility 1.1/2.0 FullSpeed
• File System FAT16/32• Maximum current less than 500 mA• Capacity less than 4 GB (1 partition)
USB device connection• When connecting a USB device, make
sure that the connector is pushed all theway into the port.
• Do not leave the USB device for longperiods of time in places inside thevehicle where the temperature can risetoo high.
• Back up any important data beforehand.We cannot accept responsibility for anylost data.
• It is recommended not to connect a USBdevice that contains data files other thanMP3/WMA format.
60M-05-48
• FILE REPEATThe repeat indicator “RPT” will light.
Recording MP3/WMA files on a USBdevice• Playback or display may not be possi-
ble depending on the type of USB
5-15
OTHER CONTROLS AND EQUIPMET
93
76G-74E
device in use or the condition of therecording.
• Depending on the connected USBmemory, the files may be played in dif-ferent order from the order that the fileswere stored.
Compression formatsMP3• Bit rate:
MPEG1 Audio Layer III: 64 k -320 kbpsMPEG2 Audio Layer III: 64 k - 160 kbps
• Sampling frequency:MPEG1 Audio Layer III: 32 k/44.1 k/48kHzMPEG2 Audio Layer III: 16 k/22.05 k/24kHz
WMA (Ver.7, Ver.8)• Bit rate: CBR 48 k -192 kbps• Sampling frequency: 32 k/44.1 k/48 kHzWMA (Ver.9*)• Bit rate: CBR 48 k - 320 kbps• Sampling frequency: 32 k/44.1 k/48 kHz* WMA 9 Professional/LossLess/Voice are
not supported.
Maximum number of files/folders• Maximum number of files: 2500 (files +
folders)• Maximum number of files in a folder:
255• Maximum depth of tree structure: 8• Maximum number of folders: 255
(Root folder is included.)
Listening to an iPod®
60M-05-049
Display
60M-05-050
(1) USB button(2) TUNE FOLDER PUSH SOUND knob(3) Up button(4) Down button(5) RPT button(6) RDM button(7) DISP button(8) Preset buttons ([1] to [6])
(A) Track title(B) Track number(C)Play time
Selecting an iPod® modePress the USB button (1).
Selecting a track• Press the Up button (3) to listen to the
next track.• Press the Down button (4) twice to lis-
ten to the previous track.When the Down button (4) is pressedonce, the track currently being playedwill start from the beginning again.
Fast forwarding/Rewinding a track• Hold down the Up button (3) to fast for-
ward the track.• Hold down the Down button (4) to fast
rewind the track.
Random playbackPress the RDM button (6).Each time the button is pressed, the modewill change as follows:
60M-05-051
• SONG RANDOM
5-16
OTHER CONTROLS AND EQUIPMENT
94
76G-74E
The random indicator “RDM” will light.The tracks in the iPod® will be playedin random order.
• ALBUM RANDOMThe random indicator “D.RDM” will light.The albums in the iPod® will be playedin random order.
Repeat playbackPress the RPT button (5).Each time the button is pressed, the modewill change as follows:
60M-05-052
• SONG REPEATThe repeat indicator “RPT” will light.The track currently being played will beplayed repeatedly.
NOTE:If text data contains more than 12 characters,the “>” mark will appear at the right end.Holding down the DISP button (7) for 1second or longer can display the next page.
Playing Mode selection1) Press the button numbered [6] of the
Preset buttons (8) for 1 second or longer.2) Turn the TUNE FOLDER PUSH SOUND
knob (2).Each time the knob is turned, the modewill change as follows:
3) Press the TUNE FOLDER PUSH SOUNDknob (2) to select the desired mode.
NOTE:• When the button numbered [6] of the
Preset buttons (8) is pressed, the previ-ous mode will be displayed.
Notes on iPod®
Supported iPod®
• iPod® touch• iPod® classic• iPod® nano (4th generation)• iPod® nano (3rd generation)• iPod® nano (2nd generation)• iPod® nano (1st generation)• iPod® (5th generation)• iPhone®
• iPhone® 3G* Some functions may not be available
depending on the model of iPod®.
Display changePress the DISP button (7).Each time the button is pressed, display willchange as follows:
60M-05-053
5-17
OTHER CONTROLS AND EQUIPMET
60M-05-054
95
76G-74E
* iPod® is a trademark of Apple Inc., regis-tered in the U.S. and other countries.
* iPhone® is a trademark of Apple Inc.,registered in the U.S. and other countries.
* Apple is not responsible for the operationof this device or its compliance withsafety and regulatory standards.
iPod® connection• Make sure to detach the iPod® after
pressing the engine switch to change theignition mode to LOCK. The iPod® may notbe shut down when it is being connectedand may result in battery depletion.
• Please do not connect iPod® accesso-ries such as an iPod® remote control orheadphones while connecting the iPod®
with the unit. The unit may not operatecorrectly.
AUX connectionTo listen to auxiliary audio sources (soldseparately) through the unit, follow theinstruction below.1) Press the AUX (CD) button (1).2) Connect the auxiliary audio source to the
AUX/USB socket (separately attached)with an AUX cable.
CAUTION:• Before connection, mute the unit, and
also keep the volume of the auxiliaryaudio source within a range that will notcause distortion.
• When the audio source is turned off,noise may be emitted. Be sure to turnoff the unit or switch to another modebefore turning off the audio source.
NOTE:• Please consult your place of purchase
for details about whether a givenauxiliary audio source can be connectedand the proper auxiliary cord to use.
• The volume and tone controls of theauxiliary audio source can be adjustedon the unit.
• In AUX mode, the volume setting is dif-ferent from another mode.
AUX Function
60M-05-055
(1) AUX (CD) button
Remote Audio Controls(if equipped)Controlling of basic functions of the audiosystem is available using the switches onthe steering wheel.
60M-05-056
Adjusting the volume• To increase the volume, hold down “+”
of the VOL switch (1). The volume willkeep on being increased until the switchis released.
• To decrease the volume, hold down “-”of the VOL switch (1). The volume willkeep on being decreased until the switchis released.
• To mute the sound, press the switch (2).
5-18
OTHER CONTROLS AND EQUIPMENT
96
76G-74E
Selecting the modePress the switch (3).Each time the button is pressed, the modewill change as follows:
60M-05-057
It is possible to turn on the audio systemby pressing the switch (3).
Selecting the radio station (FM1, FM2,AM mode)• To select the next preset station, press
“” of the switch (4) only for a moment.• To select the previous preset station,
press “” of the switch (4) only for amoment.
• To scan a higher frequency radio station,press “” of the switch (4) for 1 secondor longer.
• To scan a lower frequency radio station,press “” of the switch (4) for 1 secondor longer.
Selecting the track (CD, USB (iPod®)mode)• To skip to the next track, press “” of the
switch (4) only for a moment.• To skip to the previous track, press “”
of the switch (4) twice only for amoment.When the switch (4) is pushed downonce only for a moment, the track cur-rently being played will start from thebeginning again.
Fast forwarding/Rewinding a track• To fast forward, press “” of the switch
(4) for 1 second or longer.• To fast rewind, press “” of the switch (4)
for 1 second or longer.
Anti-Theft Feature
60M-05-058
(1) VOL PUSH POWER knob(2) Preset buttons ([1] to [6])(3) Up button(4) TUNE FOLDER PUSH SOUND knob
The anti-theft function is intended to dis-courage thefts, such as that the audio sys-tem becomes inoperable when it is installedon other vehicles.This function works by entering a PersonalIdentification Number (PIN).When the unit is disconnected from itspower source, such as when the audiosystem is removed or the battery is discon-nected, the unit will become inoperable untilthe PIN is reentered.
Setting the Anti-Theft Function1) Press the VOL PUSH POWER knob (1)
to power off.2) Hold down the buttons numbered [1] and
[6] of the Preset buttons (2) and pressthe VOL PUSH POWER knob (1).“SECURITY” will be displayed.
3) Press the Up button (3) and the buttonnumbered [1] of the Preset buttons (2)simultaneously.
4) Enter a 4-digit number to be registeredas PIN using the buttons numbered [1]- [4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSHSOUND knob (4) for 1 second or longerto set the anti-theft function.
5-19
OTHER CONTROLS AND EQUIPMET
97
76G-74E
NOTE:Take a note of the registered PIN and keepit for the future use.
Canceling the anti-theft featureTo cancel the anti-theft function, delete theregistered PIN.1) Press the VOL PUSH POWER knob (1)
to power off.2) Hold down the buttons numbered [1] and
[6] of the Preset buttons (2) and pressthe VOL PUSH POWER knob (1).“PIN ENTRY” will be displayed.
3) Press the Up button (3) and the buttonnumbered [1] of the Preset buttons (2)simultaneously.
4) Enter a 4-digit number to be registeredas PIN using the buttons numbered [1]- [4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSHSOUND knob (4) for 1 second or longerto delete the registered PIN. The indi-cation “——” will be displayed and theanti-theft function will be canceled.
NOTE:To change your PIN, first delete your cur-rent PIN, then set a new one.
to make the unit operable again.1) Set the ignition switch to the “ACC”
position. “SECURITY” will be displayed.2) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)simultaneously.
3) Enter a 4-digit number to be registeredas PIN using the buttons numbered [1]- [4] of the Preset buttons (2).
4) Hold down TUNE FOLDER PUSHSOUND knob (4) for 1 second or longer.When the PIN same as registered isentered, the power of the audio systemwill be turned off automatically and it willbecome operable again.
NOTE:If an incorrect PIN is entered, “ERROR” andthe total number of incorrect entry attemptswill be displayed.If an incorrect PIN is entered 10 times ormore, “HELP” will be displayed and theaudio system will become inoperable.
Confirming the Personal IdentificationNumber (PIN)When the main power source is discon-nected such as when the battery isreplaced, etc, it is required to enter the PIN
Battery InstallationInstall a lithium battery (CR2025) with thepoles facing the correct direction.
60M-05-059
Battery replacement timing• When battery power is depleted, the
button may not be operable. If the remotecontroller does not operate, replace thebattery and check the operation.
Caution on battery• Be sure to follow the instructions to
prevent battery leakage, over-heating,ignition or explosion.
5-20
OTHER CONTROLS AND EQUIPMENT
98
76G-74E
wwwww WARNING• Do not expose the battery to flame.
Do not short circuit, disassemble, orheat the battery.
• Do not charge the battery.• Use the specified type battery.• Keep the button-shaped battery
away from children to prevent acci-dental swallowing.
• If the battery is swallowed, contacta doctor immediately.
wwwww CAUTION• Install the battery with the poles
facing the correct direction.• When not in use for a long period
of time, or if the battery is dead,remove the battery from the remotecontroller.
dashboard exposed to direct sunlight inthe summer, as it will become extremelyhot).
• When the vehicle is parked in an areaexposed to direct sunlight, Ensure theremote controller is placed in an areanot exposed to direct sunlight. Forexample: Glove box.Under direct sunlight, signal receptionfrom the remote controller weakens. Ifthis happens, hold the remote controllerclose to the signal receptor on the frontpanel.
If battery leakage has occurred, wipe thecontainer first then install a new battery. Ifthe battery solution contacts the skin, washoff with water completely.
Caution on Remote Controller• Do not leave the remote controller in an
area exposed to direct sunlight, such ason the dashboard or steering wheel. Theremote controller may deform because ofthe heat, (Be especially careful of the
5-21
OTHER CONTROLS AND EQUIPMET
99
76G-74E
Remote Controller
Common operations
60M-05-060
5-22
OTHER CONTROLS AND EQUIPMENT
100
76G-74E
Radio operations
60M-05-061
NOTE:• When the SCAN button is pressed while pausing for receiving, it cancels the scan operation and continuously receives the station.• When the SCAN button is pressed while searching, it cancels the scan operation and stops at next receivable station.• When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will
be stored at the remaining preset buttons.
5-23
OTHER CONTROLS AND EQUIPMET
101
76G-74E
CD operations
60M-05-062
NOTE:• When the scan play is done for one round, the normal playback starts.• To cancel the scan play, press the SCAN button again.
5-24
OTHER CONTROLS AND EQUIPMENT
102
76G-74E
60M-05-063
MP3/WMA Disc operations
5-25
OTHER CONTROLS AND EQUIPMET
NOTE:• When the scan play is done for one round, the normal playback starts.• To cancel the scan play, press the SCAN button again.
103
76G-74E
USB operations
60M-05-064
5-26
OTHER CONTROLS AND EQUIPMENT
NOTE:• When the scan play is done for one round, the normal playback starts.• To cancel the scan play, press the SCAN button again.
104
76G-74E
iPod operations
60M-05-065
5-27
OTHER CONTROLS AND EQUIPMET
NOTE:• When the scan play is done for one round, the normal playback starts.• To cancel the scan play, press the SCAN button again.
105
76G-74E
TroubleshootingWhen encountered a problem, check and follow the instructions as described below.If the described suggestions do not solve the problem, it is recommended to take the unit to your authorized MARUTI SUZUKI dealer.
Problem
Common
Unable to operate
Unable to turn on the power (no sound).(No sound is produced)
Radio
Much noise
Unable to receive by auto tuning
CD
Sound skips or noise produced
Possible cause
The security function is on.
Fuse is blown.
It may not be exactly tuned in to the station.
There may be no station emitting signalspowerful enough.
The disc is dirty.
The disc has a major scratch or is warped.
Possible solution
When “SECURITY” is displayed, enter theID.When “HELP” is displayed, contact yourauthorized MARUTI SUZUKI dealer.
Contact your authorized MARUTI SUZUKIdealer.
Tune it in exactly to the station.
Pick up a station by manual tuning.
Wipe the disc with a soft cloth.
Replace the disc with the one with noscratch and also not warped.
5-28
OTHER CONTROLS AND EQUIPMENT
106
76G-74E
Problem
MP3/WMA
No playback
Sound skips or noise produced
USB
Playback does not start when the USBdevice is connected.
Possible cause
The disc contains unsupported formatteddata.
Sound skipping may occur when playingVBR (Variable Bit Rate) files.
There is no supported format file to play onthis unit.
The current consumption of the USB deviceexceeds 500 mA.
Possible solution
Check the file format.
It is not recommended to play VBR files.
Check the file format.
Use an USB device with a currentconsumption lower than 500 mA.
5-29
OTHER CONTROLS AND EQUIPMET
107
76G-74E
Error Display Messages (if applicable)
Possible solution
Insert the disc with its label side up.Check the disc if it is not warped or isfree of flaws.When ERROR 1 does not disappear evenwhen a normal disc is inserted, contactyour dealer.
When the CD is in the unit, press the CDeject button to remove the disc.When the disc cannot be ejected, contactyour dealer.
Unplug the USB device and plug it again.When ERROR 1 does not disappear,contact your dealer.
Unplug the USB device and plug it again.Check the USB device.
Check the connection of the USB device.
Check the USB device.
Possible cause
The disc cannot be read.
The player developed an error of an un-identified cause.
Inoperable due to an unidentified cause.
Impossible to communicate correctly withthe USB device.
The USB device is disconnected.
The current consumption of the USB deviceexceeds 500 mA.
Display
CD
ERROR 1
ERROR 3
USB/iPod®
ERROR 1
ERROR 2
ERROR 3
ERROR 4
5-30
OTHER CONTROLS AND EQUIPMENT
108
76G-74E
5-31
OTHER CONTROLS AND EQUIPMET
Error Display Messages (if aplicable)
Possible solution
Insert the disc with its label side up.Check the disc if it is not warped or isfree of flaws.When E1, E2 does not disappear evenwhen a normal disc is inserted, contactyour dealer.
When the CD is in the unit, press the CDeject button to remove the disc.When the disc cannot be ejected, contactyour dealer.
Check the error file.
Copyright protection CD/USB cannot bereproduced.
Unplug the USB device and plug it again.When E1, E6 does not disappear, contactyour dealer.
Check the USB device.
Check the connection of the USB device.
Check the error file.
Copyright protection CD/USB cannot bereproduced.
Possible cause
The disc cannot be read.
The player developed an error of an un-identified cause.
File decode error
Cannot reproduce by the copyrightprotection.
Inoperable due to an unidentified cause.
The current consumption of the USB deviceexceeds 1 A.
The USB device is disconnected.
File decode error
Cannot reproduce by the copyrightprotection.
Display
CD
E1, E2
E3
E4
E5
USB/iPod®
E1, E6
E2
E3
E4
E5
109
76G-74E
5-32
OTHER CONTROLS AND EQUIPMENT
Fuel Filler Cap
60M-05-066
EXAMPLE
60M-05-067
EXAMPLE
The fuel filler cap is located on the left rearside of the vehicle. The fuel filler door canbe unlocked by pulling up the opener leverlocated on the outboard side of the driver’s
seat and locked by simply closing the door.
60M-05-068
EXAMPLE
To remove the fuel filler cap:1) Open the fuel filler door.2) Remove the cap by turning it counter-
clockwise.
wwwww CAUTIONRemove the fuel filler cap slowly. Thefuel may be under pressure and mayspray out, causing injury.
60M-05-069
EXAMPLE
NOTE:If the hook (1) is equipped with the fuel fillerdoor, hold the fuel filler cap when refueling.
60M-05-070
NOTE:You can also use the cap holder (2) to holdthe fuel filler cap (3) by hooking the groove(4) when refueling.
To reinstall the fuel filler cap:1) Turn the cap clockwise until you hear
several clicks.2) Close the fuel filler door.
wwwww WARNINGFuel is extremely flammable. Do notsmoke when refueling, and make surethere are no open flames or sparks inthe area.
EXAMPLE
110
76G-74E
5-33
OTHER CONTROLS AND EQUIPMET
If you need to replace the fuel cap,use a Maruti genuine cap. Use of animproper cap can result in a malfunc-tion of the fuel system or emissioncontrol system. It may also result infuel leakage in the event of an acci-dent.
wwwww WARNING
Engine Hood
60M-05-071
To open the engine hood:1) Pull the hood release handle located on
the outboard side of the driver’s side ofthe instrument panel. This will disengagethe engine hood lock halfway.
EXAMPLE60M-05-072
EXAMPLE
2) Push the under-hood release leversideways with your finger, as shown inthe illustration. While pushing the lever,lift up the engine hood.
60M-05-073
3) Continue to lift up the hood until it ishigh enough to support with the proprod.
To close the engine hood:1) Lift the hood up slightly and remove the
prop rod from the hole. Put the prop rodback to the holding clip.
2) Lower the hood close to the bumper,then let it drop down. Make sure thehood is securely latched after closing.
wwwww WARNINGMake sure the hood is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.
Sun Visor
60M-05-074
The sun visors can be pulled down to blockglare coming through the windshield, or theycan be unhooked and turned to the side toblock glare coming through the side window.
EXAMPLE
111
76G-74E
5-34
OTHER CONTROLS AND EQUIPMENT
NOTICEWhen unhooking and hooking a sunvisor, be sure to handle it by the hardplastic parts or the sun visor can bedamaged.
Card holder (if equipped)
60M-05-075
(1) Card holderYou can put a card in the card holder (1)on the back of the sun visor.
NOTICEWhen you park your vehicle outdoorsin direct sunlight or in hot weather, donot leave plastic cards in the holder.The heat may distort them.
60M-05-076
Vanity mirror (if equipped)
(2) Vanity mirror
When using the vanity mirror, do notmove too close to a front air bag loca-tion or lean against it. If the front airbag is accidentally inflated, it could hityou hard.
wwwww WARNING
Interior Light Switch
Front (if equipped)Center (if equipped)
60M-05-077
Rear
EXAMPLE
EXAMPLE
EXAMPLE
60M-05-078
EXAMPLE
This light switch has three positions whichfunction as described below:
ON (1)The light comes on and stays on regard-less of whether the door is open or closed.
DOOR (2)The light comes on when the door isopened. After closing all doors, the light willremain on for about 15 seconds and thenfade out. If you insert the key during thistime, the light will start to fade outimmediately. After removing the key fromthe ignition switch, the light will turn on forabout 15 seconds and then fade out.
OFF (3)The light remains off even when the dooris opened.
60M-05-079
EXAMPLE
NOTE:The number of doors involved in the light-ing operation of the interior light depends onthe vehicle specification. If there is a switch
112
76G-74E
5-35
OTHER CONTROLS AND EQUIPMET
(rubber projection) at the door opening asshown, the door is involved in the lightingoperation. The tailgate is also involved in thisoperation even without the rubber projectiondepending on the vehicle specification.
Accessory Socket
60M-05-080
EXAMPLE
The accessory socket will work when theignition switch is in the “ACC” or “ON” posi-tion.This socket can be used to provide 12 volt/120 watt power for electrical accessories.
Use of inappropriate electrical acces-sories can cause damage to yourvehicle’s electrical system. Make surethat any electrical accessories you useare designed to plug into this type ofsocket.
NOTICE
AUX/USB Socket (if equipped)
60M-05-081
EXAMPLE
Connect your portable digital music player,etc. to this socket to enjoy music through thevehicle’s audio system using it as a source.Refer to “Audio System” in this section.
Assist Grips
60M-05-082
Assist grips are provided for convenience.
NOTICETo avoid damaging the assist grip andthe molded headlining, do not hangdown the assist grip.
Glove Box
60M-05-083
To open the glove box, pull the latch lever.To close it, push the lid until it latchessecurely.
wwwww WARNINGNever drive with the glove box lidopen. It could cause injury if an acci-dent occurs.
113
76G-74E
5-36
OTHER CONTROLS AND EQUIPMENT
Cup Holder and Storage AreaFront
60M-05-084
Passenger side
60M-05-085
To use the cup holder, push it. The cupholder slides out automatically. After usingthe holder, push it back to return it.
3rd row seats
60M-05-086
EXAMPLE
wwwww CAUTIONDo not use the cup holder to holdcups containing hot liquids, or sharp-edged, hard or breakable objects.Objects in the cup holder may bethrown about during a sudden stop orimpact, and could cause personalinjury.
Bottle holderFront seats
60M-05-087
60M-05-88
2nd row seats
You should hold a bottle with a cap in theholder.
EXAMPLE
EXAMPLE
114
76G-74E
5-37
OTHER CONTROLS AND EQUIPMET
Front Seat Back Pocket(if equipped)
This pocket is provided for holding light andsoft things such as gloves, newspapers ormagazines.
60M-05-089
wwwww CAUTIONDo not put hard or breakable objectsin the pocket. If an accident occurs,objects such as bottles, cans, etc. caninjure the occupants in the rear seat.
Armrest (if equipped)
2nd row seatEXAMPLE
60M-05-090
EXAMPLE
To use the armrest, pull the strap and lowerthe armrest. When not in use, push backin the seat until the armrest is secured.
wwwww WARNINGIn an accident or sudden stop, therear armrest (if equipped) could fallforward. If there is a child in a rear-facing child restraint in the centerseating position, the falling armrestcould injure the child. Make sure thearmrest is secured in the stowedposition when not in use.
NOTICETo avoid damage to the armrest, donot lean on it or allow a child to siton it.
Floor Mats (if equipped)
60M-05-091
To prevent the driver’s side floor mat fromsliding forward and possibly interfering withthe operation of the pedals, Maruti genuinepart floor mats are recommended.Whenever you put the driver’s side floor matback in the vehicle after it has beenremoved, be sure to hook the floor matgrommets to the fasteners and position thefloor mat properly in the footwell.
When you replace the floor mats in yourvehicle with a different type such as all-weather floor mats, we highly recommend
EXAMPLE
115
76G-74E
5-38
OTHER CONTROLS AND EQUIPMENT
using Maruti genuine floor mats for properfitting.
wwwww WARNINGFailure to take the following precau-tions may result in the driver’s sidefloor mat interfering with the pedalsand causing a loss of vehicle controlor an accident.• Make sure that the floor mat grom-
mets are hooked to the fasteners.• Never place additional floor mats on
top of the existing floor mats.
Luggage Box (if equipped)
60M-05-092
EXAMPLE
Pull up the straps (A) of the luggage boxcover to use the box.
NOTICEDo not allow items in the box toextend above the top of the box. Oth-erwise, the box or cover may be dam-aged.
60M-05-093
EXAMPLE
NOTE:The luggage box cover can be held openas shown in the above illustration.
NOTICEIf the luggage box cover is held openwhile driving, it can be damaged.
Do not hold open the luggage boxcover while driving.
Frame HooksFront
60M-05-094
EXAMPLE
To access the frame hook (1), remove thecover (2).The frame hook (1) is provided on the frontof the vehicle for use in emergency situa-tions and sea shipping purposes only.
NOTICEWhen you use the frame hook (1),avoid the driving that gives significantphysical shock on hook. Suchoperation can damage the hook, or thevehicle body.
Do not sudden accelerate.
116
76G-74E
The frame hook (3) is provided on the rearof the vehicle for use in emergency situationsand trailer/train/sea shipping purposes only.
Rear
60M-05-095
EXAMPLE
NOTICEWhen you use the frame hook (3),avoid the driving that gives significantphysical shock on hook. Suchoperation can damage the hook, thevehicle body or the drive system.
Do not sudden accelerate.Do not tow the vehicle heavier thanyour vehicle.
To tow your vehicle on the road or highway,follow the instruction of “Towing” in “EMER-GENCY SERVICE” section.
Other Hooks
The hook (4) is provided for trailer/train/seashipping purposes only.The hook (5) (or opposite side) is providedfor trailer/train shipping purposes only. Thehook (6) is provided for sea shipping pur-pose only.
60M-05-096
EXAMPLE
wwwww WARNING
The hooks (4) and (5) are provided fortrailer/train shipping purposes only.The hook (6) is provided for sea ship-ping purpose only.
Do not use the frame hooks to towanother vehicle or to have your vehi-cle towed on the road or highway. Thehook (1) is designed for use inemergency situations such as if yourvehicle or another vehicle gets stuckin deep mud or snow, and sea ship-ping only. The hook (3) is designedfor use in emergency situations andtrailer/train/sea shipping only.
VV VVV
wwwww WARNING
VVVV V
Never use the hooks (1) for trailer/train shipping purposes to preventdamage to the vehicle.
NOTICE
5-39
OTHER CONTROLS AND EQUIPMET
117
76G-74E
6
VEHICLE LOADING AND TOWINGVehicle Loading ................................................................................................................. 6-1Trailer Towing .................................................................................................................... 6-1
118
76G-74E
Vehicle LoadingYour vehicle was designed for specificweight capacities. The weight capacities ofyour vehicle are indicated by the GrossVehicle Weight Rating (GVWR) and theGross Axle Weight Rating (GAWR, front andrear). The GVWR and GAWR (front andrear) are listed in the “SPECIFICATIONS”section.
GVWR – Maximum permissible overallweight of the fully loaded vehicle (includingall the occupants, accessories and cargoplus the trailer nose weight if towing atrailer).GAWR – (Front and Rear) Maximum per-missible weight on an individual axle.
Actual weight of the loaded vehicle andactual loads at the front and rear axles canonly be determined by weighing the vehi-cle. Compare these weights to the GVWRand GAWR (front and rear). If the grossvehicle weight or the load on either axleexceeds these ratings, you must removeenough weight to bring the load down to therated capacity.
wwwww WARNINGNever overload your vehicle. Thegross vehicle weight (sum of theweights of the vehicle, all the occu-pants, accessories, cargo plus trailernose weight if towing a trailer) mustnever exceed the Gross VehicleWeight Rating (GVWR). In addition,never distribute a load so that theweight on either the front or rear axleexceeds the Gross Axle Weight Rat-ing (GAWR).
wwwww WARNING
Trailer TowingYour MARUTI SUZUKI was originallydesigned to carry people and a normalamount of cargo, not to tow a trailer.MARUTI SUZUKI does not recommend youuse your vehicle to tow a trailer. Towing atrailer can adversely affect handling,durability, and fuel economy.
Always distribute cargo evenly. Toavoid personal injury or damage toyour vehicle, always secure cargo toprevent it from shifting if the vehiclemoves suddenly. Place heavier objectson the floor and as far forward in thecargo area as possible. Never pilecargo higher than the top of the seatbacks.
6-1
VEHICLE LOADING AND TOWING
119
76G-74E
7
INSPECTION AND MAINTENANCEMaintenance Schedule ...................................................................................................... 7-1Periodic Maintenance Schedule ...................................................................................... 7-2Maintenance Recommended under Severe Driving Conditions ............................... 7-2Drive Belt ............................................................................................................................ 7-6Engine Oil and Filter ........................................................................................................ 7-6Engine Coolant ................................................................................................................... 7-9Air Cleaner ........................................................................................................................ 7-11Spark Plugs ...................................................................................................................... 7-11Gear Oil ............................................................................................................................. 7-12Clutch Pedal ..................................................................................................................... 7-13Fuel Filter (Diesel engine) ............................................................................................. 7-13Brakes ................................................................................................................................ 7-14Steering ............................................................................................................................. 7-16Tyres .................................................................................................................................. 7-16Battery ............................................................................................................................... 7-18Fuses .................................................................................................................................. 7-19Headlight Aiming ............................................................................................................. 7-21Bulb Replacement ............................................................................................................ 7-21Wiper Blades .................................................................................................................... 7-25Windshield Washer Fluid ............................................................................................... 7-27Air Conditioning System ................................................................................................ 7-27
120
76G-74E
60M-07-001
wwwww WARNINGYou should take extreme care whenworking on your vehicle to preventaccidental injury. Here are a few pre-cautions that you should be especiallycareful to observe:• To prevent damage or unintended
activation of the air bag system orseat belt pretensioner system, besure the battery is disconnected andthe ignition switch has been in the“LOCK” position for at least 90 sec-onds before performing any electri-cal service work on your MARUTISUZUKI. Do not touch air bagsystem components, seat beltpretensioner system components orwires.The wires are wrapped with yellowtape or yellow tubing, and the cou-plers are yellow for easy identifica-tion.
• Do not leave the engine running ingarages or other confined areas.
VV VVV
wwwww WARNING
VVVV V
• When the engine is running, keephands, clothing, tools, and otherobjects away from the fan and drivebelt. Even though the fan may notbe moving, it can automatically turnon without warning.
• When it is necessary to do servicework with the engine running, makesure that the parking brake is set fullyand the transmission is in Neutral.
• Do not touch ignition wires or otherignition system parts when startingthe engine or when the engine isrunning, or you could receive anelectric shock.
• Be careful not to touch a hotengine, exhaust manifold and pipes,muffler, radiator and water hoses.
• Do not allow smoking, sparks, orflames around fuel or the battery.Flammable fumes are present.
• Do not get under your vehicle if itis supported only with the portablejack provided in your vehicle.
• Be careful not to cause accidentalshort circuits between the positiveand negative battery terminals.
• Keep used oil, coolant, and otherfluids away from children and pets.Dispose of used fluids properly;never pour them on the ground, intosewers, etc.
7-1
INSPECTION AND MAINTENANCE
wwwww WARNING
Maintenance Schedule
The following table shows the times whenyou should perform regular maintenance onyour vehicle. This table shows in miles,kilometers and months when you shouldperform inspections, adjustments, lubricationand other services.
MARUTI SUZUKI recommends thatmaintenance on your Maruti Suzukivehicle should be performed byMARUTI SUZUKI authorised workshop/Service station.
NOTICEWhenever it becomes necessary toreplace parts on your vehicle, it isrecommended that you use MARUTIgenuine replacement parts or theirequivalent.
121
76G-74E
7-2
INSPECTION AND MAINTENANCE
Periodic Maintenance Schedule
“A” : Adjust“C” : Clean“R” : Replace or Change“I” : Inspect and correct or replace if
necessary“L” : Lubricate“T” : Tighten to Specified Torque“O” : Rotate
NOTE:This table includes services as scheduledup to 80,000 km mileage. Beyond 80,000km, carry out the same services at thesame intervals respectively.
122
76G-74E
7-3
INSPECTION AND MAINTENANCE
FREE INSPECTION PERIODIC MAINTENANCE AT COST
Interval: This interval should be judged by odometer km (x1000) 1 5 10 20 30 40 50 60 70 80
reading or months, whichever comes first. months 1 6 12 24 36 48 60 72 84 96
ENGINE
1-1. Water pump drive belt (Tension, Wear) Petrol - - - - - I - - - R
1-2. Engine Coolant (Level, Leakage) I I I R I R I R I R
1-3. Engine oil and engine oil filter - - R R R R R R R R
1-4. Cooling system hoses and connections (Leakage and Damage) I I I I I I I I I I
1-5. Engine bolts (All cylinder head and manifold fixings) - - T - T - T - T -
1-6. Engine Mounting (All cylinder head and manifold fixings) - - T - T - T - T -
1-7. Valve Clearance Petrol - - - - I - - I - -
1-8. Exhaust System (Noise, Leakage etc.) - I - I - - - - - I
1-9. Positive Crank Case Ventilation System
(Hoses, Connections and Valve)- I - I - - - - - I
1-10. Exhaust Gas Recirculation Valve Diesel - - - - C - - C - -
IGNITION
2-1. Ignition wiring (Damage, Deterioration) - - - I - I - I - I
2-2. Spark Plug (Clean and adjust the gap) Petrol - - - - - R - - - R
FUEL
3-1. Air cleaner filter element Paved-road Petrol Clean after every 5,000 KM. Replace after every 40,000KM
Diesel Replace after every 20,000 KM. Cleaning not required
Dusty Condition Petrol Clean after every 2,500 KM. or as rquired. Replace after every 40,000KM
Diesel Replace after every 20,000 KM. Cleaning not required
More frequent replacement if dust condition is severe.
3-2. Fuel tank cap, fuel lines and connections (Leakage and Damage) - I - - - I - - - I
3-3. Fuel Filter (Leakage) Petrol - - - - - R - - - R
3-4. Fuel Filter and Water Draining Diesel I I I R I R I R I R
123
76G-74E
7-4
INSPECTION AND MAINTENANCE
FREE INSPECTION PERIODIC MAINTENANCE AT COST
Interval: This interval should be judged by odometer km (x1000) 1 5 10 20 30 40 50 60 70 80
reading or months, whichever comes first. months 1 6 12 24 36 48 60 72 84 96
CLUTCH AND TRANSMISSION4-1. Clutch Pedal (Push Rod Play) I I I I I I I I I I4-2. Clutch Fluid (Level, Leakage) I I I R I R I R I R4-3. Clutch Slipping (Dragging or Excess Damage) I I I I I I I I I I4-4. Manual Transmission/Transfer or Differential Oil (Level, Leakage) I I I R I R I R I RDRIVE SHAFT5-1. Drive shaft noise I I I I I I I I I I5-2. Drive shaft boot (boot damage) - I I I I I I I I IBRAKE6-1. Brake Fluid (Level, Leakage) I I I R I R I R I R6-2. Brake Pedal (pedal - wall clearance) I I I I I I I I I I6-3. Parking brake lever and cable (Play, damage) I I I I I I I I I I6-4. Brake disc and pad (Wear) - I I I I I I I I I6-5. Brake drum and shoes (Wear) - - I I I I I I I I6-6. Master cylinder/wheel cylinder/calliper (Oil leakage, boot cut)
I I I I I R I I I R(replace piston and boot kits)
6-7. Brake hoses and pipes (Leakage, damage) I I I I I I I I I IWHEEL7-1. Tyres (air pressure, abnormal wear, crack and rotation) I I&O I&O I&O I&O I&O I&O I&O I&O I&O7-2. Wheels (Damage) I I I I I I I I I I7-3. Front/Rear wheel bearing (Loose, damage) I I I I I I I I I IFRONT / REAR SUSPENSION8-1. Suspension strut (Oil leakage, damage) I I I I I I I I I I8-2. Suspension arms / Knuckle support (Loose, damage) - I I I I I I I I I8-3. Rear spring (Damage) I I I I I I I I I I8-4. Shock absorbers (Oil leakage, damage) I I I I I I I I I I8-5. All bolts and nuts (Loose) - T T T T T T T T T8-6. Suspension arms and torsion rods - I I I I I I I I I
124
76G-74E
7-5
INSPECTION AND MAINTENANCE
FREE INSPECTION PERIODIC MAINTENANCE AT COST
Interval: This interval should be judged by odometer km (x1000) 1 5 10 20 30 40 50 60 70 80
reading or months, whichever comes first. months 1 6 12 24 36 48 60 72 84 96
STEERING9-1. Steering wheel (Play, loose) I I I I I I I I I I9-2. All rods and arms (Loose, damage, wear) I I I I I I I I I IELECTRICAL10-1. Battery electrolyte (Level, leakage) I I I I I I I I I I10-2. Wiring harness connection (Loose, damage) - I I I I I I I I I10-3. Lightening system (Operation, stains, damage) I I I I I I I I I I10-4. Horn (Operation) I I I I I I I I I I10-5. System Voltage - I I I I I I I I IBODY11-1. All chassis bolts and nuts (Tighten) - I T T T T T T T T11-2. All latches, hinges and locks (Function) I I&L I&L I&L I&L I&L I&L I&L I&L I&LROAD TEST12-1. Operation of Brakes, gear shifting and speedometer I I I I I I I I I I12-2. Body and chassis noise I I I I I I I I I IAIR CONDITIONER (if equipped)13-1. Check belt tension I I I I I I I I I I13-2. Tighten compressor mounting bolt - T T T T T T T T T13-3. All hose joint (Check, tighten) I I I I I I I I I I13-4. Check functioning of Recirc flap I I I I I I I I I I13-5. Clean condensor with low pressure water - C C C C C C C C C13-6. Check belt for frayed edges I I I I I I I I I I13-7. Check all mounting bolts I I I I I I I I I I
125
76G-74E
Drive Belt
wwwww WARNINGWhen the engine is running, keephands, hair, clothing, tools, etc. awayfrom the moving fan and drive belts.
Make sure the drive belt tension is correct.If the belt is too loose, insufficient batterycharging, engine overheating, poor powersteering, poor air conditioning, or excessivebelt wear can result. When you press thebelt with your thumb midway between thepulleys, there should be a deflectionaccording to the following chart.
The belts should also be examined toensure that they are not damaged.
If you need to replace or adjust the belt haveit done by your MARUTI SUZUKI dealer.
(For Diesel Engine Model)The drive belts tension adjusted automati-cally.
Engine Oil and Filter
Specified Oil
(For Petrol Engine Model)
(For Petrol Engine Model)
60M-07-002
60M-07-003
(1) PreferredBe sure that the engine oil you use comesunder the quality classification of SG, SH,SJ, SL or SM. Select the appropriate oilviscosity according to the above chart.
SAE 5W-30 (1) is the best choice for goodfuel economy, and good starting in coldweather.
(For Diesel Engine Model)
60M-07-004
(1) Preferred
Be sure that the engine oil you use comesunder the quality classification of ACEA A3/B4. Select the appropriate oil viscosityaccording to the above chart.
Oil Level Check
(For Petrol Engine Model)
60M-07-005
EXAMPLE
(For Diesel Engine Model)
60M-07-006
(1) MIN(2) MAX(3) Engine oil dipstick
7-6
INSPECTION AND MAINTENANCE
126
76G-74E
It is important to keep the engine oil at thecorrect level for proper lubrication of yourvehicle’s engine. Check the oil level with thevehicle on a level surface. The oil levelindication may be inaccurate if the vehicleis on a slope. The oil level should bechecked either before starting the engine orat least 5 minutes after stopping the engine.The handle of the engine oil dipstick is col-ored yellow for easy identification.
60M-07-007
Pull out the oil dipstick, wipe oil off with aclean cloth, insert the dipstick all the wayinto the engine, then remove it again. Theoil on the stick should be between theupper and lower limits shown on the stick.If the oil level indication is near the lowerlimit, add enough oil to raise the level tothe upper limit.
NOTICEFailure to check the oil level regularlycould lead to serious engine troubledue to insufficient oil.
NOTICE(For Diesel Engine Model)Do not top up the oil over the MAXlimit. Too much oil causes seriousengine trouble.
Refilling (Petrol)
60M-07-008
EXAMPLE
60M-07-009
The engine oil temperature may behigh enough to burn your fingerswhen the drain plug is loosened. Waituntil the drain plug is cool enough totouch with your bare hands.
wwwww CAUTION
7-7
INSPECTION AND MAINTENANCE
EXAMPLE
EXAMPLE
60M-07-008a
Refilling (Diesel)
EXAMPLE
Remove the oil filler cap and pour oil slowlythrough the filler hole to bring the oil levelto the upper limit on the dipstick. Be carefulnot to overfill. Too much oil is almost as
bad as too little oil. After refilling, start theengine and allow it to idle for about aminute. Stop the engine, wait about 5 min-utes and check the oil level again.
Changing Engine Oil and FilterDrain the engine oil while the engine is stillwarm.
1) Remove the oil filler cap.2) Place a drain pan under the drain plug.3) Using a wrench, remove the drain plug
and drain out the engine oil.
127
76G-74E
Tightening torque for drain plugPetrol engine:35 Nm (3.5 kg-m, 25.3 lb-ft)Diesel engine:20 Nm (2.0 kg-m, 14.5 lb-ft)
wwwww WARNINGNew and used oil can be hazardous.Children and pets may be harmed byswallowing new or used oil. Keep newand used oil and used oil filters awayfrom children and pets.Repeated, prolonged contact with usedengine oil may cause skin cancer.Brief contact with used oil may irritateskin.To minimize your exposure to usedoil, wear a long-sleeve shirt andmoisture-proof gloves (such as dish-washing gloves) when changing oil. Ifoil contacts your skin, wash thor-oughly with soap and water.Launder any clothing or rags if wetwith oil.Recycle or properly dispose of usedoil and filters.
Replace the Oil Filter1) Using an oil filter wrench, turn the oil fil-
ter counterclockwise and remove it.2) Using a clean rag, wipe off the mount-
ing surface on the engine where the newfilter will be seated.
3) Smear a little engine oil around the rub-ber gasket of the new oil filter.
4) Screw on the new filter by hand until thefilter gasket contacts the mounting sur-face.
(For Petrol Engine Model)
4) Reinstall the drain plug and new gasket.Tighten the plug with a wrench to thespecified torque.
60M-07-011
EXAMPLE
(1) Loosen(2) Tighten
Tightening (viewed from filter top)
60M-07-012
(1) Oil filter(2) 3/4 turn
(For Diesel Engine Model)
(1) Loosen(2) Tighten
60M-07-013
To tighten the oil filter properly, it isImportant to accurately identify theposition at which the filter gasket firstcontacts the mounting surface.
NOTICE
7-8
INSPECTION AND MAINTENANCE
60M-07-010
EXAMPLE
128
76G-74E
5) Tighten the filter specified turn from thepoint of contact with the mounting sur-face (or to the specified torque) using anoil filter wrench.
Tightening torque for oil filter3/4 turn orPetrol engine:14 Nm (1.4 kg-m, 10.1 lb-ft)Diesel engine:25 Nm (2.5 kg-m, 18.5 lb-ft)
To prevent oil leakage, make sure thatthe oil filter is tight, but do not over-tighten it.
NOTICE
Refill with Oil and Check for Leaks1) Pour oil through the filler hole and install
the filler cap.For the approximate capacity of the oil,refer to the “Capacities” item in the“SPECIFICATIONS” section.
2) Start the engine and look carefully forleaks at the oil filter and drain plug. Runthe engine at various speeds for at least5 minutes.
3) Stop the engine and wait about 5 min-utes. Check the oil level again and addoil if necessary. Check for leaks again.
NOTICE• When replacing the oil filter, it is
recommended that you use a Marutigenuine replacement filter. If youuse an aftermarket filter, make sureit is of equivalent quality and followthe manufacturer’s instructions.
• Oil leaks from around the oil filteror drain plug indicate incorrectinstallation or gasket damage. If youfind any leaks or are not sure thatthe filter has been properly tigh-tened, have the vehicle inspected byyour MARUTI SUZUKI dealer.
Engine Coolant
Selection of CoolantTo maintain optimum performance anddurability of your engine, use Maruti genuineCoolant or equivalent.
This type of coolant is best for your coolingsystem as it:• Helps maintain proper engine temperature.• Gives proper protection against freezing
and boiling.• Gives proper protection against corrosion
and rust.Failure to use the proper coolant can dam-age your cooling system. Your authorizedMARUTI SUZUKI dealer can help you selectthe proper coolant.
NOTICETo avoid damaging your cooling sys-tem:• Always use a high quality ethylene
glycol base non-silicate type coolantdiluted with distilled water at thecorrect mixture concentration.
• Make sure that the proper mix is 30/70 coolant to distilled water forpetrol and 50/50 for diesel. In nocase higher than 70/30. Concen-trations greater than 70/30 coolantto distilled water will cause over-heating conditions.
• Do not use straight coolant norplain water.
• Do not add extra inhibitors or addi-tives. They may not be compatiblewith your cooling system.
• Do not mix different types of basecoolants. Doing so may result inaccelerated seal wear and/or thepossibility of severe overheating andextensive engine damage.
Coolant Level CheckCheck the coolant level at the reservoirtank, not at the radiator. With the enginecool, the coolant level should be betweenthe “FULL” and “LOW” marks.
7-9
INSPECTION AND MAINTENANCE
129
76G-74E
Adding Coolant
wwwww WARNINGEngine coolant is harmful or fatal ifswallowed or inhaled. Do not drinkantifreeze or coolant solution. If swal-lowed, do not induce vomiting. Imme-diately contact a poison control centeror a physician. Avoid inhaling mist orhot vapors; if inhaled, remove to freshair. If coolant gets in eyes, flush eyeswith water and seek medical attention.Wash thoroughly after handling.Solution can be poisonous to animals.Keep out of the reach of children andanimals.
• The mixture you use should contain50% concentration of antifreeze.
• If the lowest ambient temperature inyour area is expected to be –35°C(–31°F) or below, use higher con-centrations up to 60% following theinstructions on the antifreeze con-tainer.
NOTICE
(For Petrol Engine Model)
60M-07-014
If the coolant level is below the “LOW”mark, more coolant should be added.Remove the reservoir tank cap and addcoolant until the reservoir tank level reachesthe “FULL” mark. Never fill the reservoirtank above the “FULL” mark.
NOTICEWhen putting the cap on the reservoirtank, line up the mark on the cap andthe mark on the tank. Failure to followthis can result in coolant leakage.
(For Diesel Engine Model)
60M-07-015
It is hazardous to remove the reser-voir tank cap (degassing tank cap) fora diesel engine when the water tem-perature is high, because scaldingfluid and steam may be blown outunder pressure. Wait until the coolanttemperature has lowered beforeremoving the cap.
wwwww WARNING
If the coolant level is below the “LOW”mark, more coolant should be added. Whenthe engine is cool, remove the degassingtank cap by turning it anticlockwise slowlyto release any pressure. And add coolantuntil the degassing tank level reaches the“FULL” mark. Never fill the degassing tankabove the “FULL” mark.
7-10
INSPECTION AND MAINTENANCE
130
76G-74E
Coolant ReplacementSince special procedures are required, werecommend you take your vehicle to yourMARUTI SUZUKI dealer for coolantreplacement.
Air Cleaner
(For Petrol Engine Model)
60M-07-016
60M-07-017
(For Diesel Engine Model)
If the air cleaner is clogged with dust, therewill be greater intake resistance, resultingin decreased power output and increasedfuel consumption.
Unclamp the side clamps or loosen thescrews, and remove the element from theair cleaner case. If it appears to be dirty,replace it with a new one.Clamp the side clamps or tighten thescrews securely.
spark plug gap.
Spark PlugsFor nickel spark plugs (traditional type):You should inspect spark plugs periodicallyfor carbon deposits. When carbon accu-mulates on a spark plug, a strong sparkmay not be produced. Remove carbondeposits with a wire or pin and adjust the
60M-07-018
To access the spark plug:1) Unclamp the side clamps and loosen the
screws, then remove the air cleanercase.
2) If necessary, disconnect the coupler (1)
60M-07-019
7-11
INSPECTION AND MAINTENANCE
EXAMPLE
131
76G-74E
while pushing the release lever.3) Remove the ignitor bolts.4) Pull the spark plug boots out.
NOTE:When installation, make sure the wires,couplers, sealing rubber of air cleaner assyand washers, are correctly returned in place.
60M-07-020
EXAMPLE
NOTICEWhen disconnecting the spark plugcables, pull on the boot, not on thecable itself. Pulling on the cable candamage it.When servicing the iridium/platinumspark plugs (slender center electrodetype plugs), do not touch the centerelectrode, as it is easy to damage.
60M-07-021
NOTICE• When installing the spark plugs,
screw them in with your fingers toavoid stripping the threads. Tightenwith a torque wrench to 17.5 Nm(1.8 kg-m, 13.0 lb-ft). Do not allowcontaminants to enter the enginethrough the spark plug holes whenthe plugs are removed.
• Never use spark plugs with thewrong thread size.
60M-07-022
NOTICEWhen replacing spark plugs, youshould use the brand and type speci-fied for your vehicle. For the specifiedplugs, refer to the “SPECIFICATIONS”section at the end of this book. If youwish to use a brand of spark plugother than the specified plugs, consultyour MARUTI SUZUKI dealer.
Gear Oil
Specified Gear OilWhen adding gear oil, use gear oil with theappropriate viscosity and grade as shownin the chart below.
We highly recommend you use:API GL-4 SAE 75W-90 for manualtransmission gear oil.
Manual transmission oil (API GL-4)
60M-07-022a
7-12
INSPECTION AND MAINTENANCE
132
76G-74E
Gear Oil Level Check
Manual transmission
60M-07-023
(1) Oil filler and level plug
To check the gear oil level, use the follow-ing procedure:
1) Park the vehicle on a level surface withthe parking brake applied. Then, stop theengine.
2) Remove the oil filler and level plug (1).3) Check the inside of the hole with your
finger. If the oil level comes up to thebottom of the plug hole, the oil level iscorrect. If so, reinstall the plug.
4) If the oil level is low, add gear oilthrough the oil filler and level plug hole(1) until the oil level reaches the bottomof the filler hole, then reinstall the plug.
Tightening torque for oil filler andlevel plug (1)Manual transmission:21 Nm (2.1 kg-m, 15.2 lb-ft)
wwwww CAUTIONAfter driving the vehicle, the gear oiltemperature may be high enough toburn you. Wait until the oil filler plugis cool enough to touch with yourbare hands before inspecting gear oillevel.
NOTICEWhen tightening the plug, apply thefollowing sealing compound orequivalent to the plug threads to pre-vent oil leakage.SUZUKI Bond No. “1216E” or “1217G”
Gear Oil ChangeSince special procedures, materials andtools are required, it is recommended thatyou trust this job to your authorizedMARUTI SUZUKI dealer.
Clutch Pedal
Fluid Control Clutch
Check the clutch pedal for smooth opera-tion and clutch fluid level from time to time.If clutch dragging is felt with the pedal fullydepressed, have the clutch inspected byyour MARUTI SUZUKI dealer. If the clutchfluid level is near the “MIN” line, fill it upto the “MAX” line with SAE J1703 or DOT3brake fluid.
60M-07-024
Fuel Filter (Diesel engine)
60M-07-025
7-13
INSPECTION AND MAINTENANCE
EXAMPLE
133
76G-74E
The fuel filter works as a water sedimentoras well.Drain water according to the PeriodicMaintenance Schedule. To drain water:1) Remove the battery. (Refer to “Battery”
in this section.)2) Place a pan or ample rag under the fuel
filter drain nozzle.3) Loosen the drain knob. The water will be
drained.4) Tighten the drain knob when the water
changes to the diesel fuel.5) Tighten the drain knob.
Tightening torque for drain knob1.5 Nm (0.15 kg-m, 1.1 lb-ft)
Brakes
Brake Fluid
60M-07-026
Check the brake fluid level by looking at thereservoir in the engine compartment. Checkthat the fluid level is between the “MAX”and “MIN” lines. If the brake fluid level isnear the “MIN” line, fill it up to the “MAX”line with MARUTI GENUINE brake fluid.
Failure to follow the guidelines belowcan result in personal injury or seri-ous damage to the brake system.• If the brake fluid in the reservoir
drops below a certain level, thebrake warning light on the instru-ment panel will come on (the enginemust be running with the parkingbrake fully disengaged). Should thelight come on, immediately ask yourMARUTI SUZUKI dealer to inspectthe brake system.
• A rapid fluid loss indicates a leak inthe brake system which should beinspected by your MARUTI SUZUKIdealer immediately.
• Do not use any fluid other thanMARUTI GENUINE brake fluid. Do notuse reclaimed fluid or fluid that hasbeen stored in old or open contain-ers. It is essential that foreign parti-cles and other liquids are kept outof the brake fluid reservoir.
wwwww WARNING
wwwww CAUTIONBrake fluid can harm your eyes anddamage painted surfaces. Use cautionwhen refilling the reservoir.
Brake fluid is harmful or fatal if swal-lowed, and harmful if it comes in con-tact with skin or eyes. If swallowed,do not induce vomiting. Immediatelycontact a poison control center or aphysician. If brake fluid gets in eyes,flush eyes with water and seek medi-cal attention. Wash thoroughly afterhandling. Solution can be poisonousto animals. Keep out of the reach ofchildren and animals.
wwwww WARNING
7-14
INSPECTION AND MAINTENANCE
134
76G-74E
NOTE:With disc brakes, the fluid level can beexpected to gradually fall as the brake padswear.
Brake PedalCheck if the brake pedal stops at the regu-lar height without “spongy” feeling when youdepress it. If not, have the brake systeminspected by your MARUTI SUZUKI dealer.If you doubt the brake pedal for the regularheight, check it as follows:
Pedal to floor carpet minimum distance“a”: 59 mm (2.3 in.)
With the engine running, measure the dis-tance between the brake pedal and floorcarpet when the pedal is depressed withapproximately 30 kg (66 lbs) of force. Theminimum distance required is as specified.Since your vehicle’s brake system is self-adjusting, there is no need for pedaladjustment.If the pedal to floor carpet distance asmeasured above is less than the minimumdistance required, have your vehicle
inspected by your MARUTI SUZUKI dealer.
NOTE:When measuring the distance between thebrake pedal and floor carpet, be sure notto include the accessory floor mat or rubbermat on the floor wall in your measurement.
60M-07-028
60M-07-027
wwwww WARNINGIf you experience any of the followingproblems with your vehicle’s brakesystem, have the vehicle inspectedimmediately by your MARTUI SUZUKIdealer.• Poor braking performance• Uneven braking (brakes not working
uniformly on all wheels.)• Excessive pedal travel• Brake dragging• Excessive noise
Parking Brake
60M-07-029
Ratchet tooth specification “b”:4th – 9thLever pull force (1):200 N (20 kg, 44 lbs)
Check the parking brake for proper adjust-ment by counting the number of clicks madeby the ratchet teeth as you slowly pull upon the parking brake lever to the point offull engagement. The parking brake levershould stop between the specified ratchetteeth and the rear wheels should besecurely locked. If the parking brake is notproperly adjusted or the brakes drag afterthe lever has been fully released, have theparking brake inspected and/or adjusted byyour MARUTI SUZUKI dealer.
7-15
INSPECTION AND MAINTENANCE
EXAMPLE
135
76G-74E
Steering
60M-07-030
Steering wheel play “c”:0 – 30 mm (0.0 – 1.2 in.)
Check the play of the steering wheel bygently turning it from left to right and mea-suring the distance that it moves before youfeel slight resistance. The play should bebetween the specified values.Check that the steering wheel turns easilyand smoothly without rattling by turning itall the way to the right and to the left whiledriving very slowly in an open area. If theamount of free play is outside the specifi-cation or you find anything else to bewrong, an inspection must be performed byyour MARUTI SUZUKI dealer.
Tyres
60M-07-031
The front and rear tyre pressure specifica-tions for your vehicle are listed on the TyreInformation Label. Both the front and reartyres should have the specified tyre pres-sure.
EXAMPLE
Tyre InspectionInspect your vehicle’s tyres at least once amonth by performing the following checks:
1) Measure the air pressure with a tyregauge. Adjust the pressure if necessary.Remember to check the spare tyre, too.
wwwww WARNING
• Check the inflation pressure fromtime to time while inflating the tyregradually, until the specified pres-sure is obtained.
• Never underinflate or overinflate thetyres.Underinflation can cause unusualhandling characteristics or cancause the rim to slip on the tyrebead, resulting in an accident ordamage to the tyre or rim.Overinflation can cause the tyre toburst, resulting in personal injury.Overinflation can also causeunusual handling characteristicswhich may result in an accident.
• Air pressures should be checkedwhen the tyres are cold or you mayget inaccurate readings.
VV VVV
wwwww WARNING
VVVV V
60M-07-032
EXAMPLE
7-16
INSPECTION AND MAINTENANCE
EXAMPLE
136
76G-74E
(1) Tread wear indicator(2) Indicator location mark
2) Check that the depth of the tread grooveis more than 1.6 mm (0.06 in.). To helpyou check this, the tyres have molded-in tread wear indicators in the grooves.When the indicators appear on the treadsurface, the remaining depth of the treadis 1.6 mm (0.06 in.) or less and the tyreshould be replaced.
3) Check for abnormal wear, cracks anddamage. Any tyres with cracks or otherdamage should be replaced. If any tyresshow abnormal wear, have them inspectedby your MARUTI SUZUKI dealer.
wwwww CAUTIONHitting curbs and running over rockscan damage tyres and affect wheelalignment. Be sure to have tyres andwheel alignment checked periodicallyby your MARUTI SUZUKI dealer.
4) Check for loose wheel nuts.5) Check that there are no nails, stones or
other objects sticking into the tyres.
wwwww WARNING
type and size. This is important toensure proper steering and handlingof the vehicle. Never mix tyres ofdifferent size or type on the fourwheels of your vehicle. The size andtype of tyres used should be onlythose approved by MARUTI SUZUKIas standard or optional equipmentfor your vehicle.
• Replacing the wheels and tyresequipped on your vehicle with cer-tain combinations of aftermarketwheels and tyres can significantlychange the steering and handlingcharacteristics of your vehicle.
• Therefore, use only those wheel andtyre combinations approved byMARUTI SUZUKI as standard oroptional equipment for your vehicle.
• Your MARUTI SUZUKI is equippedwith tyres which are all the same
VV VVV
wwwww WARNING
VVVV V
NOTICEReplacing the original tyres with tyresof a different size may result in falsespeedometer or odometer readings.
Tyre Rotation
60M-07-033
To avoid uneven wear of your tyres and toprolong their life, rotate the tyres as illus-trated. Tyres should be rotated asmentioned in periodic maintenanceschedule. After rotation, adjust front andrear tyre pressures to the specification listedon your vehicle’s Tyre Information Label.
7-17
INSPECTION AND MAINTENANCE
Wheel BalancingIf the vehicle vibrates abnormally on smoothroad, have the wheel balanced at MarutiSuzuki Authorized Workshop.
Wheel AlignmentIn case of abnormal tyre wear or pullingtowards one side, have the wheel alignedat Maruti Suzuki Authorized Workshop.
137
76G-74E
Tubeless Tyres (If equipped)The vehicle is equipped with TubelessTyres. In tubeless tyre, a thin layer of butylrubber is used for lining the inside of thetubeless tyre. This layer is to prevent airloss and fulfilling the purpose of tube. Theair pressure is maintained by the sealingbetween tyre bead and wheel rim. Tubelesstyres are having advantage of slow air lossand preventing sudden deflation whiledriving.
Care and maintenance tips for tubelesstyres1) Always maintain recommended inflation
pressure. Driving continously at lowinflation pressure can lead to tyredamage.
2) In case any leakage is found, check forany nail penetration/valve core damageor rim bent. Damaged wheel must notbe used.
3) In case tyre has run at low pressue, itmust be inspected for any defect.
4) Whenver new tyre is fitted, replace thevalve.
5) If continous high speed driving isrequired, increase tyres pressure by 5psi over recommended inflation pressure.
6) Never run the tyre beyond TWI (Treadwear indicator). The tyre isrecommended to be replaced when theremaining tread has worn to this point.
The indicators are spaced across thetread around the tyre marked by atriagular symbol (TWI).
7) Always prefer tubeless tyre mountingmachine. In case of manual mountingtyre/wheel rim damage may occur.
8) In case of any problem, please get intouch with MARUTI SUZUKI Authorizedworkshop.
wwwww WARNING
Battery
• Batteries produce flammablehydrogen gas. Keep flames andsparks away from the battery or anexplosion may occur. Never smokewhen working in the vicinity of thebattery.
• When checking or servicing thebattery, disconnect the negativecable. Be careful not to cause ashort circuit by allowing metalobjects to contact the battery postsand the vehicle at the same time.
• To avoid harm to yourself ordamage to your vehicle or battery,follow the jump starting instructionsin the “EMERGENCY SERVICE”section of this manual if it isnecessary to jump start yourvehicle.
60M-07-034
Petrol
60M-07-034a
EXAMPLE-1 EXAMPLE-2
Diesel
EXAMPLE
The level of the battery solution must bekept between the “Max” and the “Min” levellines at all times. If the level is found to be
7-18
INSPECTION AND MAINTENANCE
138
76G-74E
60M-07-035
To remove the battery:1) Disconnect the negative cable (1).2) Disconnect the positive cable (2).
3) Remove the retainer nuts (3) andremove the retainer (4).
4) Remove the battery.
To install the battery:1) Install the battery in the reverse order
of removal.2) Tighten the retainer nuts and battery
cables securely.
NOTE:When the battery is disconnected, some ofthe vehicle’s function will be initialized and/or deactivated.These function are required to reset afterthe battery is reconnected.
EXAMPLE
Replacement of the battery
below the “Min” level line, add distilled waterto bring level between “Max” and “Min”. Youshould, however, periodically check thebattery, battery terminals and batteryholddown bracket for corrosion. Removecorrosion using a stiff brush and ammoniamixed with water, or baking soda mixed withwater. After removing corrosion, rinse withclean water.If your vehicle is not going to be driven fora month or longer, disconnect the cablefrom the negative terminal of the battery tohelp prevent discharge..
FusesYour vehicle has three types of fuses, asdescribed below:
Main fuseThe main fuse takes current directly fromthe battery.
Primary fusesThese fuses are between the main fuse andindividual fuses, and are for electrical loadgroups.
Individual fusesThese fuses are for individual electrical cir-cuits.
To remove a fuse, use the fuse puller pro-vided in the fuse box.
60M-07-036
60M-07-038
60M-09-037
Fuses in the Engine Compartment
7-19
INSPECTION AND MAINTENANCE
139
76G-74E
MAIN FUSE / PRIMARY FUSE
(1)100 A FL1 (GAS)
120 A FL1 (DIESEL)
(2) 100 A FL2
(3) 100 A FL3
(4) 50 A FL4
(5) 80 A FL5
(6) 100 A FL6 (DIESEL)
(7) 50 A Ignition switch -2
(8) 7.5 A ECM (DIESEL)
(9) – Blank
(10) – Blank
(11) 10 A Air compressor
(12) 15 A FI (GAS)
(13) 30 A FI (DIESEL)
(14) 60 A Power steering
(15) 30 A Radiator fan
(16) 40 A ABS motor
(17) 40 A Blower fan
(18) 30 A Starting motor
(19) – Blank
(20) 30 A Back up
(21) – Blank
(22) 15 A Head light (Left)
(23) 25 A ABS control module
(24) 15 A Head light (Right)
(25) 20 A Front fog light
(26) – Blank
(27) 40 A Ignition switch
(28) 7.5 A Starting Signal
(29) 20 A INJ DRV (DIESEL)
(30) 10 A FI2 (DIESEL)
(31) 15 A F/P (DIESEL)
The main fuse, primary fuses and some ofthe individual fuses are located in theengine compartment. If the main fuse blows,no electrical component will function. If aprimary fuse blows, no electrical componentin the corresponding load group will function.When replacing the main fuse, a primaryfuse or an individual fuse, use a Marutigenuine part replacement.To remove a fuse, use the fuse puller providedin the fuse box. The amperage of each fuseis shown in the back of the fuse box cover.
60M-07-039
wwwww WARNINGIf the main fuse or a primary fuseblows, be sure to have your vehicle
VV VVV
wwwww WARNING
inspected by an authorized MARUTISUZUKI dealer. Always use a Marutigenuine replacement. Never use asubstitute such as a wire even for atemporary repair, or extensiveelectrical damage and a fire can result.
NOTE:Make sure that the fuse box always carriesspare fuses.
Fuses under the Dash Board
60M-07-040
EXAMPLE
VVVV V
7-20
INSPECTION AND MAINTENANCE
140
76G-74E
60M-07-41
PRIMARY FUSE
(1) 30 A Belt
(2) – Blank(3) – Blank(4) 20 A Rear defogger
(5) – Blank(6) – Blank
(7) – Blank(8) 7.5 A Starting Signal
(9) 15 A ACC-2(10) 30 A Power window(11) 10 A Hazard
(12) – Blank(13) 15 A Ignition coil
(14) 10 A ABS control module(15) 15 A ACC
(16) – Blank(17) 15 A Horn(18) 10 A Stop light
(19) 10 A Air bag(20) 10 A Back-up light
(21) 15 A Rear wiper / Washer
(22) 25 A Front wiper
(23) 7.5 A Dome light
(24) – Blank
(25) 7.5 A RR fog lamp
(26) – Blank
(27) 7.5 A Ignition-1 signal
(28) – Blank
(29) – Blank
(30) 15 A Radio
(31) 10 A Tail lamp
(32) 20 A D/L
(33) 7.5 A Cruise control
(34) 10 A Meter
(35) 7.5 A Ignition-2 signal
(36) – Blank
60M-07-042
wwwww WARNINGAlways be sure to replace a blownfuse with a fuse of the correct amper-
VV VVV
age. Never use a substitute such asaluminum foil or wire to replace ablown fuse. If you replace a fuse andthe new one blows in a short periodof time, you may have a major electri-cal problem. Have your vehicleinspected immediately by yourMARUTI SUZUKI dealer.
wwwww WARNING
VVVV V
Headlight AimingSince special procedures are required, werecommend you take your vehicle to yourMARUTI SUZUKI dealer for headlightalignment.
Bulb Replacement
wwwww CAUTION• Light bulbs can be hot enough to
burn your finger right after beingturned off. This is true especially forhalogen headlight bulbs. Replace thebulbs after they become coolenough.
• The headlight bulbs are filled withpressurized halogen gas. They canburst and injure you if they are hitor dropped. Handle them carefully.
7-21
INSPECTION AND MAINTENANCE
141
76G-74E
NOTICEThe oils from your skin may cause ahalogen bulb to overheat and burstwhen the lights are on. Grasp a newbulb with a clean cloth.
NOTICEFrequent replacement of a bulb indi-cates the need for an inspection ofthe electrical system. This should becarried out by your MARUTI SUZUKIdealer.
60M-07-043
Interior Light
Front / Center
Rear
Pull down the lens by using a flat bladescrewdriver covered with a soft cloth asshown. To install it, simply push it back in.The bulb can be removed by simply pullingit out. When replacing the bulb, make surethat the contact springs are holding the bulbsecurely.
Headlight
60M-07-045
60M-07-044
Open the engine hood. Disconnect thecoupler (1). Remove the sealing rubber (2).Push the retaining spring (3) forward and
unhook it. Then remove the bulb. Install anew bulb in the reverse order of removal.
60M-07-046
NOTE:You can see the position of retaining spring(3) from the hole of headlight.
Side Turn Signal Light (if equipped)
60M-07-047
7-22
INSPECTION AND MAINTENANCE
142
76G-74E
Remove the light housing by sliding to leftwith your finger.
60M-07-048
To remove a bulb holder from a light hous-ing, turn the holder clockwise and pull it out.Then remove the bulb. Install a new bulbin the reverse order.
To remove a bulb holder from a light hous-ing, turn the holder counterclockwise andpull it out. To install the holder, push theholder in and turn it clockwise.
Bulb
Other General Lights
Bulb holder
60M-07-049
(1) Removal(2) Installation
60M-07-050
(3) Removal(4) Installation
There are two types of bulb, “Full glasstype” (1) and “Glass/metal type” (2).
To remove and install a full glass type bulb(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) froma bulb holder, push in the bulb and turn itcounterclockwise. To install a new bulb,push it in and turn it clockwise.
You can access the individual bulb or bulbholders as follows.
EXAMPLE
EXAMPLE
Front turn signal light (1)Front position light (2)
60M-07-051
60M-07-052
Front fog light (if equipped)1) Start the engine. Turn the steering wheel
to the opposite side of the replacing foglight to replace the bulb easily. Then turnoff the engine.
EXAMPLE
7-23
INSPECTION AND MAINTENANCE
143
76G-74E
2) Insert a flat blade screwdriver into thehole (2) and remove the clips (1) by twistthe driver as shown in the illustration.
60M-07-053
3) Open the fender cover. Disconnect thecoupler with pushing the lock release.Turn the bulb holder counterclockwiseand remove it.
Rear combination light(tail, stop, turn signal, etc.)
60M-07-054
Remove the screw (1). Remove the combi-nation light (2) by pulling it outside.
License plate lightSince special procedures are required, werecommend you take your vehicle to yourMARUTI SUZUKI dealer for bulbreplacement.
High-mount stop light
60M-07-055
To remove a high-mount stop light housingthe following procedure:1) Open the tailgate, and remove the nuts
(1) as shown in the illustration.
EXAMPLE
EXAMPLE
2) Close the tailgate. Release the claws (3)of the light housing by a flat bladescrewdriver, etc. The claws are shownin the next illustration. Remove a high-mount stop light housing (2) from thetailgate.
60M-07-056
60M-07-057
3) Remove the each bulb.4) Replace the bulbs.
To install a high-mounted stop lighthousing in the reverse order of removal.
7-24
INSPECTION AND MAINTENANCE
144
76G-74E
Rear fog light (if equipped)
60M-07-058
1) Remove the nuts (1) as shown in theillustration.
2) Remove the rear fog light by pushing thebolt (2).
60M-07-059
3) Remove the bolts (3) and open thecover.
Wiper Blades
60M-07-060
If the wiper blades become brittle or dam-aged, or make streaks when wiping, replacethe wiper blades.
To install new wiper blades, follow the pro-cedures below.
NOTICETo avoid scratching or breaking thewindow, do not let the wiper armstrike the window while replacing thewiper blade.
NOTE:Some wiper blades may be different fromthe ones described here depending onvehicle specifications. If so, consult yourMARUTI SUZUKI dealer for properreplacement method.
For windshield wipers:
60M-07-061
1) Hold the wiper arm away from the win-dow.
60M-07-062
2) Squeeze lock (1) towards wiper arm (2)and remove the wiper frame from the
EXAMPLE
7-25
INSPECTION AND MAINTENANCE
145
76G-74E
arm as shown.3) Unlock the lock end of the wiper blade
and slide the blade out as shown.
60M-07-063
60M-07-064
(3) Retainer
4) If the new blade is provided without thetwo metal retainers, move them from theold blade to the new one.
60M-07-065
60M-07-066
(A) Up(B) Down
NOTE:When you install the metal retainers (3),make sure the direction of metal retainersas shown in the above illustrations.
EXAMPLE
EXAMPLE
(4) Locked end
5) Install the new blade in the reverse orderof removal, with the locked end positionedtoward the wiper arm. Make sure theblade is properly retained by all thehooks. Lock the blade end into place.
6) Reinstall wiper frame to arm, makingsure that the lock lever is snappedsecurely into the arm.
60M-07-067
EXAMPLE
60M-07-068
For rear wipers:
1) Hold the wiper arm away from the win-dow.
7-26
INSPECTION AND MAINTENANCE
146
76G-74E
2) Remove the wiper frame from the armas shown.
3) Slide the blade out as shown.
60M-07-069
NOTE:Do not flex the wiper blade frame end morethan necessary. If you do, it can break off.
(1) Retainer
4) If the new blade is provided without thetwo metal retainers, move them from theold blade to the new one.
5) Install the new blade in the reverse orderof removal.Make sure the blade is properly retainedby all the hooks.
6) Reinstall wiper frame to arm in thereverse order of removal.
60M-07-070
Windshield Washer Fluid
EXAMPLE
wwwww WARNINGDo not use “anti-freeze” solution inthe windshield washer reservoir. Thiscan severely impair visibility whensprayed on the windshield, and alsodamage your vehicle’s paint.
NOTICEDamage may result if the washermotor is operated with no fluid in thewasher tank.
60M-07-071
Check that there is washer fluid in the tank.Refill it if necessary. Use a good qualitywindshield washer fluid, diluted with wateras necessary.
Air Conditioning SystemIf you do not use the air conditioner for along period, such as during winter, it maynot give the best performance when youstart using it again. To help maintain opti-mum performance and durability of your airconditioner, it needs to be run periodically.Operate the air conditioner at least once amonth for one minute with the engine idling.This circulates the refrigerant and oil andhelps protect the internal components.
7-27
INSPECTION AND MAINTENANCE
147
76G-74E
8
EMERGENCY SERVICETyre Changing Tool ........................................................................................................... 8-1Jacking Instructions ........................................................................................................... 8-2Jump Starting Instructions ............................................................................................... 8-5Towing .................................................................................................................................. 8-6If the Starter Does Not Operate ...................................................................................... 8-6If the Engine is Flooded ................................................................................................... 8-6If the Engine Overheats .................................................................................................... 8-6
EMERGENCY SERVICE
148
76G-74E
Tyre Changing Tool
60M-08-001
The tyre changing tools are stowed in theright side of the luggage compartment.Remove the cover to access the tools.
To remove the jack, turn its shaft counter-clockwise and pull the jack out of the stor-age bracket.
To stow the jack, place it in the storagebracket and turn the shaft clockwise untilthe jack is securely held in place.
After using the tyre changing tools, besure to stow them securely or theycan cause injury if an accident occurs.
wwwww WARNING
wwwww CAUTIONThe jack should be used only tochange wheels. It is important to readthe jacking instructions in this sectionbefore attempting to use the jack.
The spare tyre is stowed under the rearfloor.
To remove the spare tyre:
60M-08-002
EXAMPLE
1) Remove the cap and loosen the sparetyre holder hook bolt with the lug wrench.
NOTICELoose the spare tyre holder hook boltuntil you can remove the hook byyourself. If the bolt is loosen too much,the hook might off and the spare tyremight drop off to the ground.
60M-08-003
2) Unhook the spare tyre holder and lowerit slowly.
3) Remove the tyre.
To install the spare tyre:1) Install the spare tyre facing up the out-
side of the wheel in the reverse orderof removal.
2) Tighten the spare tyre holder hook boltsecurely.
wwwww WARNINGDo not drive your vehicle with theloose spare tyre holder hook bolt, oth-erwise it may come loose or the sparetyre may drop off, which can result inan accident.
8-1
EMERGENCY SERVICE
149
76G-74E
Tighten the spare tyre holder hook boltsecurely. However, do not overtightenthe bolt, it may be warped or broken.
NOTICE
Tightening torque for the spare tyreholder hook bolt30 Nm (3.0 kg-m, 21.7 lb-ft)
Jacking Instructions
60M-08-004
1) Place the vehicle on level, hard ground.2) Set the parking brake firmly and shift
into “R” (Reverse) if your vehicle has amanual transmission.
wwwww WARNING
• Never jack up the vehicle with thetransmission in “N” (Neutral). Otherwise,unstable jack may cause an accident.
• Be sure to shift into “R” (Reverse)for a manual transmission vehiclewhen you jack up the vehicle.
VV VVV
wwwww WARNING
VVVV V
3) Turn on the hazard warning flasher ifyour vehicle is near traffic.
4) Block the front and rear of the wheeldiagonally opposite of the wheel being lifted.
5) Place the spare wheel near the wheelbeing lifted as shown in the illustrationin case that the jack slips.
60M-08-005
60M-08-006
60M-08-007
6) Position the jack at an angle as shownin the illustration and raise the jack byturning the jack handle clockwise untilthe jack-head groove fits around thejacking bar beneath the vehicle body.
7) Continue to raise the jack slowly andsmoothly until the tyre clears the ground.Do not raise the vehicle more thannecessary.
wwwww WARNING• Use the jack only to change wheels
on level, hard ground.• Never jack up the vehicle on an
inclined surface.• Never raise the vehicle with the jack
in a location other than thespecified jacking point (shown in the
VV VVV
8-2
EMERGENCY SERVICE
150
76G-74E
wwwww WARNING
illustration) near the wheel to bechanged.Especially, do not raise the vehiclewith a jack at a part of the torsionbeam which is located under thevehicle body, between rear wheels.
• Make sure that the jack is raised atleast 51 mm (2 inches) before itcontacts the flange. Use of the jackwhen it is within 51 mm (2 inches)of being fully collapsed may resultin failure of the jack.
• No person should place any portionof their body under a vehicle that issupported by a jack.
• Never run the engine when thevehicle is supported by the jack andnever allow passengers to remain inthe vehicle.
VVVV V
To Raise the Vehicle with a Garage Jack• Apply the garage jack to one of the
points indicated below.• Always support the raised vehicle with
jack stands (commercially available) atthe points indicated below.
60M-08-008
(1) Front(2) Jack stand(3) Jacking point for onboard jack(4) Rear(5) Front suspension frame(6) Jacking point for garage jack(7) Application point for two-column lift and
jack stand
NOTICE• Never apply a garage jack to the
exhaust pipe or engine undercoverand rear torsion beam.
• When you apply a garage jack tothe rear jacking point, it may inter-fere with the rear bumper depend-ing on the shape of the garage jack.
NOTE:For more details, please contact an authorized MARUTI SUZUKI dealer.8-3
EMERGENCY SERVICE
151
76G-74E
Changing Wheels
To change a wheel, use the following pro-cedure:
1) Clear all passengers and luggage fromthe vehicle.
2) Remove the jack, tools and spare wheelfrom the vehicle.
3) Loosen, but do not remove the wheelnuts.
4) Jack up the vehicle (follow the jackinginstructions in this section).
wwwww WARNING• Be sure to shift into “R” (Reverse)
in manual transmission when youjack up the vehicle.
• Never jack up the vehicle with thetransmission in “N” (Neutral). Other-wise, unstable jack may cause anaccident.
Tightening torque for wheel nuts100 Nm (10.0 kg-m, 72.3 lb-ft)
8) Lower the jack and fully tighten the nutsin a crisscross fashion with a wrench asshown in the illustration.
5) Remove the wheel nuts and wheel.6) Before installing the new wheel, clean
any mud or dirt off from the surface ofthe wheel and hub with a clean cloth.Clean the hub carefully; it may be hotfrom driving.
7) Install the new wheel and replace thewheel nuts with their cone shaped endfacing the wheel. Tighten each nutssnugly by hand until the wheel issecurely seated on the hub.
60M-08-009
wwwww WARNINGUse genuine wheel nuts and tightenthem to the specified torque as soonas possible after changing wheels.Incorrect wheel nuts or improperlytightened wheel nuts may come looseor fall off, which can result in anaccident. If you do not have a torquewrench, have the wheel nuts torquechecked by an authorized MARUTISUZUKI dealer.
Full Wheel Cover (if equipped)
60M-08-010
60M-08-011
When installing the cover, make sure thatit is positioned so that it does not cover orfoul the air valve.
EXAMPLE
EXAMPLE
8-4
EMERGENCY SERVICE
Insert a piece of cloth between the spokesof the wheel cover and try to pull the coveroutward (as shown in figure). Take out thedetached wheel cover from the wheel rim. Forinstallation first match the slot at the wheelcover with the air filling nozzle of the wheel.Apply equal pressure at the circumference ofthe wheel cover to fix it in the wheel rim.
EXAMPLE
152
76G-74E
After Changing WheelsStow the tyre changing tools (jack, jackhandle and lug wrench) in place. Also, stowthe flat tyre in the spare tyre stowed position.Refer to “Tyre Changing Tool” in this section.
NOTICERepair or replace the flat tyre immedi-ately. If the flat tyre is placed in thespare tyre stowed position for longtime, it can cause vehicle shakiness,noise, or scratches.
Jump Starting Instructions
wwwww WARNING• Never attempt to jump start your
vehicle if the battery appears to befrozen. Batteries in this conditionmay explode or rupture if jumpstarting is attempted.
• When making jump lead connec-tions, be certain that your handsand the jump leads remain clearfrom pulleys, belts, or fans.
• Batteries produce flammablehydrogen gas. Keep flames andsparks away from the battery or anexplosion may occur. Never smokewhen working in the vicinity of thebattery.
VV VVV
• If the booster battery you use forjump starting is installed in anothervehicle, make sure the two vehiclesare not touching each other.
• If your battery discharges repeat-edly, for no apparent reason, haveyour vehicle inspected by an autho-rized MARUTI SUZUKI dealer.
• To avoid harm to yourself or dam-age to your vehicle or battery, fol-low the jump starting instructionsbelow precisely and in order.If you are in doubt, call for qualifiedroad service.
wwwww WARNING
VVVV VYour vehicle should not be started bypushing or towing. This startingmethod could result in permanentdamage to the catalytic converter andhigh pressure pump (diesel). Use jumpleads to start a vehicle with a weakor flat battery.
NOTICE
When using a battery installed onanother vehicle, DO NOT LET THEVEHICLES TOUCH. Set the parkingbrakes fully on both vehicles.
2) Turn off all vehicle accessories, exceptthose necessary for safety reasons (forexample, headlights or hazard lights).
When Jump Starting Your Vehicle, Usethe Following Procedure:1) Use only a 12-volt battery to jump start
your vehicle. Position the good 12-voltbattery close to your vehicle so that thejump leads will reach both batteries.
60M-08-012
3) Make jump lead connections as follows:
1. Connect one end of the first jumplead to the positive (+) terminal of theflat battery (1).
2. Connect the other end to the positive(+) terminal of the booster battery (2).
3. Connect one end of the second jumplead to the negative (–) terminal of thebooster battery (2).
4. Make the final connection to anunpainted, heavy metal part (i.e.
8-5
EMERGENCY SERVICE
EXAMPLE
153
76G-74E
engine hook (3)) of the engine of thevehicle with the flat battery (1).
wwwww WARNINGNever connect the jump lead directlyto the negative (–) terminal of the dis-charged battery, or an explosion mayoccur.
4) If the booster battery you are using isfitted to another vehicle, start the engineof the vehicle with the booster battery.Run the engine at moderate speed.
5) Start the engine of the vehicle with theflat battery.
6) Remove the jump leads in the exactreverse order in which you connectedthem.
TowingIf you need to have your vehicle towed,contact a professional service. Your dealercan provide you with detailed towinginstructions.
NOTICETo help avoid damage to your vehicleduring towing, proper equipment andtowing procedures must be used.
using either of the following methods.
1) From the front, with the front wheelslifted and the rear wheels on the ground.Before towing, make sure that theparking brake is released.
2) From the rear, with the rear wheels liftedand the front wheels on the ground,provided the steering and drivetrain arein operational condition. Before towing,make sure that transmission is in neutral,the steering wheel is unlocked (theignition key should be in the “ACC”position), and the steering wheel issecured with a clamping device designedfor towing service.
2-Wheel Drive (2WD) ManualTransmissionManual transmission vehicles may be towed
NOTICEThe steering column is not strongenough to withstand shocks trans-mitted from the front wheels duringtowing. Always unlock the steeringwheel before towing.
2) If the headlights remain bright, check thefuses. If the reason for failure of thestarter is not obvious, there may be amajor electrical problem. Have the vehi-cle inspected by your authorizedMARUTI SUZUKI dealer.
If the Engine is FloodedIf the engine is flooded with Petrol, it maybe hard to start. If this happens, press theaccelerator pedal all the way to the floorand hold it there while cranking the engine.(Do not operate the starter motor for morethan 15 seconds).
If the Starter Does Not Operate1) Try turning the ignition switch to the
“START” position with the headlightsturned on to determine the battery con-dition. If the headlights go excessivelydim or go off, it usually means thateither the battery is flat or the batteryterminal contact is poor. Recharge thebattery or correct battery terminal con-tact as necessary.
If the Engine OverheatsThe engine could overheat temporarily undersevere driving conditions. If the enginecoolant temperature gauge indicatesoverheating during driving:
1) Turn off the air conditioner, if equipped.2) Take the vehicle to a safe place and
park.3) Let the engine run at the normal idle
speed for a few minutes until the indica-tor is within the normal, acceptabletemperature range between “H” and “C”.
wwwww WARNINGIf you see or hear escaping steam,stop the vehicle in a safe place andimmediately turn off the engine to let
VV VVV
8-6
EMERGENCY SERVICE
154
76G-74E
it cool. Do not open the hood whensteam is present. When the steam canno longer be seen or heard, open thehood to see if the coolant is stillboiling. If it is, you must wait until itstops boiling before you proceed.
wwwww WARNINGVVVV V
If the temperature indication does not comedown to within the normal, acceptablerange:
1) Turn off the engine and check that thewater pump belt and pulleys are notdamaged or slipping. If any abnormalityis found, correct it.
2) Check the coolant level in the reservoir.If it is found to be lower than the “LOW”line, look for leaks at the radiator, waterpump, and radiator and heater hoses. Ifyou locate any leaks that may havecaused the overheating, do not run theengine until these problems have beencorrected.
3) If you do not find a leak, carefully addcoolant to the reservoir and then theradiator, if necessary. (Refer to “EngineCoolant” in the “INSPECTION ANDMAINTENANCE” section.)
wwwww WARNING
60M-08-013
• It is hazardous to remove the radia-tor cap (or degassing tank cap fora diesel engine) when the watertemperature is high, becausescalding fluid and steam may beblown out under pressure. The capshould only be taken off when thecoolant temperature has lowered.
• To help prevent personal injury,keep hands, tools and clothing awayfrom the engine cooling fan and air-conditioner fan (if equipped). Theseelectric fans can automatically turnon without warning.
8-7
EMERGENCY SERVICE
155
76G-74E
9
Corrosion Prevention ......................................................................................................... 9-1Vehicle Cleaning ................................................................................................................. 9-2
APPEARANCE CARE
156
76G-74E
Corrosion PreventionIt is important to take good care of yourvehicle to protect it from corrosion. Listedbelow are instructions for how to maintainyour vehicle to prevent corrosion. Pleaseread and follow these instructions carefully.
Important Information About Corrosion
Common causes of corrosion1) Accumulation of road salt, dirt, moisture,
or chemicals in hard-to-reach areas ofthe vehicle underbody or frame.
2) Chipping, scratches and any damage totreated or painted metal surfacesresulting from minor accidents or abra-sion by stones and gravel.
Environmental conditions which accel-erate corrosion1) Road salt, dust control chemicals, sea
air or industrial pollution will all acceler-ate the corrosion of metal.
2) High humidity will increase the rate ofcorrosion particularly when the temper-ature range is just above the freezingpoint.
3) Moisture in certain areas of a vehicle foran extended period of time may promotecorrosion even though other bodysections may be completely dry.
4) High temperatures will cause an accel-erated rate of corrosion to parts of thevehicle which are not well ventilated topermit quick drying.
specifically intended for your purposes.Follow the manufacturer’s directions whenusing these special cleaners.
Repair finish damageCarefully examine your vehicle for damageto the painted surfaces. Should you find anychips or scratches in the paint, touch themup immediately to prevent corrosion fromstarting. If the chips or scratches have gonethrough to the bare metal, have a qualifiedbody shop make the repair.
Keep passenger and luggage compart-ments cleanMoisture, dirt or mud can accumulate underthe floor mats and may cause corrosion.Occasionally, check under these mats toensure that this area is clean and dry. Morefrequent checks are necessary if the vehicleis used off road or in wet weather.Certain cargos such as chemicals, fertiliz-ers, cleaners, salts, etc. are extremely cor-rosive by nature. These products should betransported in sealed containers. If a spillor leak does occur, clean and dry the areaimmediately.
Store your vehicle in a dry, well-venti-lated areaDo not park your vehicle in a damp, poorlyventilated area. If you often wash yourvehicle in the garage or if you frequentlydrive it in when wet, your garage may bedamp. The high humidity in the garage may
This information illustrates the necessity ofkeeping your vehicle (particularly theunderbody) as clean and dry as possible.It is equally important to repair any damageto the paint or protective coatings as soonas possible.
How to Help Prevent Corrosion
Wash your vehicle frequentlyThe best way to preserve the finish on yourvehicle and to help avoid corrosion is tokeep it clean with frequent washing.Wash your vehicle at least once during thewinter and once immediately after the win-ter. Keep your vehicle, particularly theunderside, as clean and dry as possible.If you frequently drive on salted roads, yourvehicle should be washed at least once amonth during the winter. If you live near theocean, your vehicle should be washed atleast once a month throughout the year.
For washing instructions, refer to the “Vehi-cle Cleaning” section.
Remove foreign material depositsForeign material such as salts, chemicals,road oil or tar, tree sap, bird droppings andindustrial fall-out may damage the finish ofyour vehicle if it is left on painted surfaces.Remove these types of deposits as quicklyas possible. If these deposits are difficult towash off, an additional cleaner may berequired. Be sure that any cleaner you useis not harmful to painted surfaces and is
9-1
APPEARANCE CARE
157
76G-74E
cause or accelerate corrosion. A wet vehiclemay corrode even in a heated garage if theventilation is poor.
wwwww WARNINGDo not apply additional undercoatingor rust preventive coating on oraround exhaust system componentssuch as the catalytic converter,exhaust pipes, etc. A fire could bestarted if the undercoating substancebecomes overheated.
60M-09-001
Vehicle Cleaning
wwwww WARNING
solvents such as lacquer thinners,Petrol, benzene or cleaning materialssuch as bleaches or strong householddetergents. The materials could causepersonal injury or damage to thevehicle.
When cleaning the interior or exteriorof the vehicle, NEVER USE flammable
VV VVV
wwwww WARNING
VVVV V
Cleaning the InteriorVinyl upholsteryPrepare a solution of soap or mild deter-gent mixed with warm water. Apply thesolution to the vinyl with a sponge or softcloth and let it soak for a few minutes toloosen dirt.Rub the surface with a clean, damp clothto remove dirt and the soap solution. Ifsome dirt still remains on the surface,repeat this procedure.
Fabric upholsteryRemove loose dirt with a vacuum cleaner.Using a mild soap solution, rub stainedareas with a clean damp cloth. To removesoap, rub the areas again with a clothdampened with water. Repeat this until thestain is removed, or use a commercial fabriccleaner for tougher stains. If you use afabric cleaner, carefully follow the manu-facturer’s instructions and precautions.
Seat beltsClean seat belts with a mild soap andwater. Do not use bleach or dye on thebelts. They may weaken the fabric in thebelts.
Vinyl floor matsOrdinary dirt can be removed from vinyl withwater or mild soap. Use a brush to helploosen dirt. After the dirt is loosened, rinsethe mat thoroughly with water and dry it inthe shade.
CarpetsRemove dirt and soil as much as possiblewith a vacuum cleaner. Using a mild soapsolution, rub stained areas with a cleandamp cloth. To remove soap, rub the areasagain with a cloth dampened with water.Repeat this until the stain is removed, oruse a commercial carpet cleaner for tougherstains. If you use a carpet cleaner, carefullyfollow the manufacturer’s instructions andprecautions.
Instrument panel and consoleNOTE:Wipe up spills containing chemicals, alco-hol, etc., immediately with a soft, dampcloth. Use a mild soap solution if necessary.Do not use cleaners or polishes containingstrong solvents or acidic solutions. Thesechemicals may stain and discolor theinstrument panel and console.
9-2
APPEARANCE CARE
158
76G-74E
Cleaning the Exterior
NOTICEIt is important that your vehicle bekept clean and free from dirt. Failureto keep your vehicle clean may resultin fading of the paint or corrosion tovarious parts of the vehicle body.
Caring for Aluminum WheelsNOTE:• Do not use an acidic or alkaline deter-
gent to wash aluminum wheels. Thesetypes of detergent will cause permanentspots, discoloration and cracks on fin-ished surfaces.
• Do not use a bristle brush and soapcontaining an abrasive material. Thesewill damage finished surfaces.
Washing
60M-09-002
wwwww WARNING• Never attempt to wash and wax your
vehicle with the engine running.• When cleaning the underside of the
body and fender, where there maybe sharp-edged parts, you shouldwear gloves and a long-sleeved shirtto protect your hands and armsfrom being cut.
• After washing your vehicle, carefullytest the brakes before driving tomake sure they have maintainedtheir normal effectiveness.
When washing the vehicle, park it wheredirect sunlight does not fall on it and followthe instructions below:1) Flush the underside of body and wheel
housings with pressurized water toremove mud and debris. Use plenty ofwater.
NOTICEWhen washing the vehicle:• Avoid directing steam or hot water
of more than 80°C (176°F) on plas-tic parts.
• To avoid damaging engine compo-nents, do not use pressurized waterin the engine compartment.
2) Rinse the body to loosen the dirt. Removedirt and mud from the body exterior withrunning water. You may use a soft spongeor brush. Do not use hard materials whichcan scratch the paint or plastic. Rememberthat the headlight covers or lenses aremade of plastic in many cases.
NOTICETo avoid damage to the paint or plas-tic surface, do not wipe the dirt offwithout ample water. Be sure to fol-low above procedure.
3) Wash the entire exterior with a milddetergent or car wash soap using asponge or soft cloth. The sponge orcloth should be frequently soaked in thesoap solution.
NOTICEWhen using a commercial car washproduct, observe the cautions speci-fied by the manufacturer. Never usestrong household detergents or soaps.
4) Once the dirt has been completelyremoved, rinse off the detergent withrunning water.
5) After rinsing, wipe off the vehicle bodywith a wet chamois or cloth and allowit to dry in the shade.
9-3
APPEARANCE CARE
159
76G-74E
6) Check carefully for damage to paintedsurfaces. If there is any damage, “touch-up” the damage following the procedurebelow:1. Clean all damaged spots and allow
them to dry.2. Stir the paint and “touch-up” the
damaged spots lightly using a smallbrush.
3. Allow the paint to dry completely.
NOTICEIf you use an automatic car wash,make sure that your vehicle’s bodyparts, such as spoilers, cannot bedamaged. If you are in doubt, consultthe car wash operator for advice.
60M-09-003
Waxing
After washing the vehicle, waxing and pol-ishing are recommended to further protectand beautify the paint.• Only use waxes and polishes of good
quality.• When using waxes and polishes,
observe the precautions specified by themanufacturers.
9-4
APPEARANCE CARE
160
76G-74E
MEMO
9-5
APPEARANCE CARE
161
76G-74E
10
GENERAL INFORMATIONVehicle Identification ........................................................................................................ 10-1
162
76G-74E
Vehicle Identification
Chassis Serial Number
60M-10-001
EXAMPLE
60M-10-002
EXAMPLE
The chassis and/or engine serial numbersare used to register the vehicle. They arealso used to assist your dealer when order-
ing or referring to special service informa-tion. Whenever you have occasion toconsult your MARUTI SUZUKI dealer,remember to identify your vehicle with thisnumber. Should you find the number difficultto read, you will also find it on the identifica-tion plate.
Engine Serial Number
60M-10-002
The engine serial number is stamped on thecylinder block as shown in the illustration.
10-1
GENERAL INFROMATION
163
76G-74E
SPECIFICATIONSNOTE:Specifications are subject to change withoutnotice.
ITEM: Dimensions UNIT: mm
Overall length 4265
Overall width 1695
Overall height 1685
Wheelbase 2740
Track Front 1480
Rear 1490
Ground clearance 185
ITEM: Mass (weight) UNIT: kg
Curb mass (weight) Petrol 1160 - 1180
Diesel 1235 - 1255
Gross vehicle mass (weight) rating Petrol 1760
Diesel 1845
Gross axle mass (weight) rating Front Petrol 820
Diesel 900
Rear Petrol 990
Diesel 990
Petrol: Petrol engine modelDiesel: Diesel engine model
11-1
SPECIFICATIONS
11
164
76G-74E
ITEM: Engine
Type K14B (DOHC) D13A (DOHC)
Number of cylinders 4 4
Bore 73.0 mm (2.87 in.) 69.6 mm (2.74 in.)
Stroke 82.0 mm (3.23 in.) 82.0 mm (3.23 in.)
Piston displacement 1373 cm³ 1248 cm³(1373 cc, 83.8 cu.in) (1248 cc, 76.1 cu.in)
Compression ratio 10.0 ± 0.4 : 1 17.6 ± 0.4 : 1
ITEM: Electrical
Standard spark plug Petrol NGK KR6A-10
Battery Petrol 12V 34B20L & 38B20L
Diesel 12V DIN 65L & DIN 60L
Fuses See “INSPECTION AND MAINTENANCE” section.
11-2
SPECIFICATIONS
165
76G-74E
ITEM: Lights WATTAGE BULB No.
Headlight 12V 60/55W H4
Turn signal light Front 12V 21W PY21W
Rear 12V 21W PY21W
Side turn signal light (on fender) 12V 5W WY5W
Side turn signal light (on outside rearview mirror) LED –
Position light 12V 5W W5W
Tail/brake light 12V 21/5W P21/5W
License plate light 12V 5W W5W
Reversing light 12V 16W W16W
Interior light (center) 12V 10W –
Interior light (rear) 12V 10W –
Front fog light 12V 35W H8
Rear fog light 12V 21W P21W
High mount stop light 12V 5W W5W
11-3
SPECIFICATIONS
166
76G-74E
ITEM: Wheel and Suspension
Tyre size, front and rear 185/65R15 88*1S
Rim size 15X5 1/2J
Tyre pressures For the specified tyre pressure, see the Tyre Information Label locatedon the driver’s door lock pillar.
* 1 If you connot prepare a tyre with the specified load index rate, prepare a tyre with higher load index rate.
ITEM: Capacities (approx.)
Coolant (including reservoir tank) Petrol 5.1 L
Diesel 6.3 L
Fuel tank 45 L
Engine oil 3.1 L (replacement with oil filter)
Transmission oil 2.6 L
11-4
SPECIFICATIONS