4/13/2012 14/17/2010 www.CodeDataPlate.com 1
NAESA WESTERN REGIONAL WORKSHOP
April 13, 2012
Alteration/Modernization Inspection Criteria
by: John S. Rearick
CodeDataPlate.com
4/13/2012 2www.CodeDataPlate.com
DisclaimerThe opinions and recommendations presented here are strictly my own and are not those of ASME, IAEC, NAESAI or any organization of which I may be a member.All references to the Code are from A17.1a-2005 Copyright © 2004 by the American Society of Mechanical Engineers.
JSRearick
4/13/2012 3www.CodeDataPlate.com
Challenges Facing InspectorsNew in 2000 and later editions• More than ½ the units in the USA were under 1996• Now under A17.1-2000, -04, -07, or -10 plus addenda• New numbering system
– Harmonization with B-44• Some areas have added Private Inspectors• Increased penalties for non-compliance• Lots of misinformation about:
– Adopted Codes & Effective Dates– Code Data Plate Requirements– Required Signage– Inspection Tag Requirements
4/13/2012 4Courtesy of NAESAI
A17.1-1996
A17.1b-1998
A17.1b-1998
A17.1a-1997
4/13/2012 5
Central Region
Eastern RegionW
este
rn R
egio
n
A17.1a-2008 A17.1a-2005
A17.1-2007A17.1-2004
4/13/2012 6
ST/PROV AHJ CITY AHJ Contact
A17.1 and addenda
effective
Existing
Installations
A17.3
Suspension
Standard
A17.6
Preformance
Based
A17.7
W/C Lifts A18.1
Auto-Adoption AHJ Insp Pvt Insp
Chief Inspector When
Alaska Bill McCauley/Al Nagel a-2005 6/14/2006 or 06/16/2006-2002 -2003 xAnchorage Anchorage Brice Burnett 2007 1-Jul-11 -2005 x
Arizona -2004 15-Mar-03Pheonix Phoenix Mark Gustafson
California Debra Tudor -2004 1-May-08Los Angeles Los Angeles Peter Callas -2004 1-May-08
Colorado Mike Stewart -2007 1-Jan-09 -2005 provisions -2005 x xBolderDenverPikes Peak Regional
Hawaii Maurice Morita d-2000 19-Jun-00Idaho Al Caine//Jean Frenette a-2005 2-Apr-08 -2005 provisions -2005Kansas Karl W. McNorton a-2005 12-Apr-06
Topeka Topeka Craig Johnson/Leo Martinez b-1989 23-Oct-06Wichita Wichita T Kerschen -2004 1-Jan-07 -2003 x
Montana Mike Cooney a-2005 1/26/05 || 2/27/04 -2002 -2003 xNebraska Bud Witt 2007 3/14/2009
Lincoln LincolnNevada Dave Richardson -2007 <10/06/2007/12/15/2004>-2002 -2007New Mexico Lisa Martinez -2004 1/21/2005
Albuquerque AlbuquerqueNorth Dakota Cal Steiner a-2005 1/11/2007
Bismark Bismarck Ray ZieglerOklahoma Tom Monroe a-2008 6/5/2009 -2008 -2007 -2008 x
Okla. City Oklahoma City Randy Edwards -2000 12/1/2004 -2002Tulsa Tulsa Dale Gero | Roger Adams -2000 5/1/2004 -2002
Oregon 2007 1/1/2009South DakotaTexas Lawrence Taylor -2007 9/1/08//91/03 -2002 -2005
Houston Houston Mike Dorosk -2007 9/1/2008 -2002 -2005Utah Michael Pederson -2007 <06/02/2009||4/12/2006>-2002 -2005Washington Jack Day
Seattle Seattle Bill Watson a-2008 9/23/2010Wyoming
NAESA West Reg.
www.CodeDataPlate.com
4/13/2012 7
From Code Data Plate to Acceptance Inspection Tag
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
#REF!
codedataplate.com
ALTERATION CODE: ASME A17.1-2000
SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.11.5, 8.7.2.13, 8.7.3.8, 8.7.3.12, 8.7.3.23.7, 8.7.3.24, 8.7.3.29, 8.7.3.30, 8.7.3.31.1, 8.7.3.31.2, 8.7.3.31.5, 8.7.3.31.8
CODE DATA PLATE
INSTALLATION CODE: ASA A17.1-1965
###
INSTALLATION CODE: ANSI A17.1b-1980
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.11.1, 8.7.2.12, 8.7.2.14.1, 8.7.2.19, 8.7.2.20, 8.7.2.27.4, 8.7.2.28
codedataplate.com
CODE DATA PLATE
4/13/2012 8
From Code Data Plate to Acceptance Inspection Tag
• Scope of a Modernization– What is Retained– What is New – What is Altered
• Scope of Acceptance Inspection– What was Retained– What was New – What was Altered
4/13/2012 9
Scope of Alteration
Courtesy of Bill Synder
Start With This
4/13/2012 10
Scope of Alteration
End With This
Courtesy of Bill Synder
Destination Dispatch
Compass Destination Entry
MRLGen 2
Synergy
EcoSpace / MonoSpace
Synchron Hoisting Machine
?
4/13/2012 11
Scope of Modernization or Alteration
• Entrance and Door Work
• Cab Work
• Shaft or Hoistway Work
• Motor or Machine Room Work
• Changes in Speed, Rise/Travel or Capacity
• Changes in Operation or Use
4/13/2012 12
Scope of Alteration• Retained Equipment
– Hoistway, Rails, Counterweight– Buffers and Other Pit Equipment– Platform, Safeties and Governor
• New Equipment– Controls– Door & Cab Equipment– Rope Brake
• Altered Equipment– Machine
4/13/2012 13
Harmonization• A17.1-1996 (25 Parts)
– Introduction (Scope & Definitions)– Part 1 & Part 2 ( HW & Traction)– Part 3 (Hydraulic Elevators)– Parts 6, 16 and 18 (Hand, R&P, SC)– Parts 4, 5, 15, 17, 19, 22, 23 and 25– Parts 8 and 9 (Esc. & MW)– Parts 7 and 14 (DW & ML)– Parts 10, 11, 12 and 13 (Insp, Alts, etc)– Introduction (Reference Codes)– Appendices – Parts 20 and 21 (Chair & Platform Lifts)
• A17.1-2004 (9 Parts)– Part 1 (General)– Part 2 (Electric)– Part 3 (Hydraulic)– Part 4 (Other Mach.)– Part 5 (Special App.)– Part 6 (Esc. & MW)– Part 7 (DW & ML)– Part 8 (General Req.)– Part 9 (Reference)– Appendices– A18.1-2005
4/13/2012 14
A17.1-2000 Code Organization• Part 1 - Scope, Purpose and Definitions
• Part 2 - Electric Elevators
• Part 3 - Hydraulic Elevators
• Part 4 - Other Types of Machines
• Part 5 - Special Applications
• Part 6 - Escalators & Moving Walks
• Part 7 - Dumbwaiters & Material Lifts
• Part 8 - General Requirements– Section 8.7 – Alterations– Section 8.10 – Acceptance Inspections
4/13/2012 15
A17.1 Code Organization
• Part 9 - Referenced Documents
• Figures
• Tables
• Non-Mandatory Appendices
• Index
4/13/2012 16
Parts 1 & 2• Part 1 Scope, Purpose &
Definitions• Part 2 requirements:
– 2.1/2 Hoistways & Pits– 2.3 Guarding of Cwt.– 2.4/5 Clearances– 2.6 Under Hoistway– 2.7/10 Machinery– 2.11/13 Doors– 2.14/16 Cars– 2.17 Safeties
– 2.18 Governors– 2.19 ACOS/UIM– 2.20 Ropes– 2.21 Counterweights– 2.22 Buffers– 2.23 Rails– 2.24 Machines– 2.25 Limits– 2.26 Controls– 2.27 Emerg. Oper. & F/S– 2.28/9 Drawings & Ident.
4/13/2012 17
Parts 3 through 8
• Part 3 Hydraulic• Part 4 Rack & Pinion,
Screw Column, Hand• Part 5 Special App.
– LULA– Residence– Sidewalk
• Part 6 Escalators• Part 7 Dumbwaiters
• Part 8 General– 8.1 Security– 8.4/5 Seismic– 8.6 Maintenance,
Repair, Replacement and Testing (in’08)
– 8.7 Alterations– 8.8 Welding– 8.9 Code Data Plate– 8.10 Acceptance
Inspections (new and alterations
– 8.11 Periodic Inspections
4/13/2012 18
Parts 9 and Appendices
• Part 9 References• Nonmandatory
Appendices (A - R)– A=Control System– B=Door Landing and
Unlocking Zones– F=ACOS/UIM– J=Relationship of Pit
Ladder to Hoistway Door Unlocking Means
– L=Index of Alteration Requirements
– N=Recommended Inspection and Test Intervals in “Months”
– Q=Explanatory Figures for the Definitions of Elevator Machinery Space, etc
– R=Inspection Operation and Hoistway Access Switch Operation Hierarchy
• Index
4/13/2012 19
8.9 Code Data Plate
• Guide to Acceptance Inspection
• Guide to Periodic Inspections
• Original Installation Code
• Alteration Code
• Section 8.7 Requirements complied with
• Appendix L is Guide to 8.7 Requirements
4/13/2012 20www.CodeDataPlate.com
8.9 Code Data Plate
#REF!
codedataplate.com
ALTERATION CODE: ASME A17.1-2000
SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.11.5, 8.7.2.13, 8.7.3.8, 8.7.3.12, 8.7.3.23.7, 8.7.3.24, 8.7.3.29, 8.7.3.30, 8.7.3.31.1, 8.7.3.31.2, 8.7.3.31.5, 8.7.3.31.8
CODE DATA PLATE
INSTALLATION CODE: ASA A17.1-1965
Door Operator
Wiring
Re-opening Devise
Door Restrictor
Plunger Gripper
Valve
Tank
Limits
Top of Car Insp..
Leveling
Controller Replacement
Emergency Operations
4/13/2012 21
SECTION 8.7ALTERATIONS
4/13/2012 26
###
INSTALLATION CODE: ANSI A17.1b-1980
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
CODE DATA PLATE
Entrance and Door Work Cab Work
Hoistway Work - Wiring
Machine Room Work – Rope Gripper, New Motor, Controls and Fire Service
4/13/2012 27
Hoistway Work
• 8.7.2.1 – Hoistway Enclosures
• 8.7.2.2 – Pits
• 8.7.2.3 through 8.7.2.6 H/W Cwt. Items
• 8.7.2.7 – Machine Room
• 8.7.2.8 – Wiring
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 28
Hoistway WorkTypical Items and What gets Dragged in
8.7.3.2 Pits {1203.1f} Alterations made to the pit shall conform to
• 2.1.2.3 - Strength of Pit Floor
• All of Section 2.2 - Pits
See also 8.7.3.4 - Vertical Car and Counterweight Clearances and Runbys
Note: Often Pit Alterations are required when a Jack is replaced.
Red is what was in 1996 code. Black is new in 2000 and later
4/13/2012 29
Hoistway WorkTypical Items and What gets Dragged in
8.7.2.1.5 Control of Smoke and Hot Gases {1201.1e} (Hoistway Ventilation) shall conform to:
2.1.4 Control of Smoke and Hot GasesWhen required by the building code, hoistways shallbe provided with means to prevent the accumulation ofsmoke and hot gases.Where air pressurization of the hoistway is utilizedas a means of smoke and hot gas control, the air shallnot be introduced into the hoistway in such a manneras to cause erratic operation by impingement of travelingcables, selector tapes, governor ropes, compensatingropes, and other components sensitive to excessivemovement or deflection.
4/13/2012 30
Hoistway and Machine Room WorkTypical items and what else gets dragged in
8.7.2.8 or 8.7.3.8 Wiring {1201.3 or 1203.1c}
Electrical Equipment, Wiring, Pipes, and Ducts in Hoistways and Machine Rooms. The installation of any new, or the alteration of existing, electrical equipment, wiring, raceways, cables, pipes, or ducts shall conform to the applicable requirements of 2.8 (…shall conform to NFPA 70)
Red is what was in 1996 code. Black is new in 2000 and later
4/13/2012 31
Door Specifications
• 8.7.2.10 - Entrances
• 8.7.2.11 - Hoistway Door Locking Devices– Interlocks– Door Restrictors
• 8.7.2.12 - Door Operators
• 8.7.2.13 - Reopening Devises
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 32
What gets Dragged in
• Replace H/W Door Tracks & Hangers• 8.7.2.10.1 & 8.7.2.10.2 {1201.10a & 1201.10b}
8.7.2.10.1(c) Where an alteration is made to any hoistwayentrance, it shall conform to 2.11.3, 2.11.5, 2.11.7, 2.11.8,and 8.7.2.10.5. The entire installation shall also conformto 2.12 and 2.13.
8.7.2.10.2(b) Hanger tracks and track supports shall conform to 2.11.11.2.
8.7.2.10.2(d) Hangers shall conform to 2.11.11.4.9 Requirements
4/13/2012 33
What gets Dragged in• Replace H/W Door Tracks & Hangers
– Shall conform to:– 2.11.3 Closing of Hoistway Doors– 2.11.5 Projection of Entrances and Other
Equipment Beyond the Landing Sills– 2.11.7 Glass in Hoistway Doors– 2.11.8 Weights for Closing or Balancing Doors– 8.7.2.10.5 Marking of Entrance Assemblies– 2.12 Hoistway Door Locking Devices and Electric
Contacts, and Hoistway Access Switches– 2.13 Power Operation of Hoistway Doors and Car
Doors– 2.11.11.2 Hangers, Tracks, and Track Supports– 2.11.11.4 Hangers
4/13/2012 34
What gets Dragged in• Replace H/W Door Tracks & Hangers
– 2.11.11.2 Hangers, Tracks, and Track Supports
Hangers, tracks, and their supports and fastenings for doors shall be constructed to withstand, without damage or appreciable deflection, an imposed static load equal to four times the weight of each panel as applied successively downward and upward at the vertical centerline of the panel. (See 2.11.11.5.7 and 2.11.11.5.8.)
4/13/2012 35
What gets Dragged in• Replace H/W Door Tracks & Hangers
2.11.11.4 Hangers. Hangers shall conform to
2.11.11.4.1 Means shall be provided to prevent
the hangers from jumping the track.
2.11.11.4.2 Stops shall be provided in the entrance assembly to prevent hangers from overrunning the end of the track.
4/13/2012 36
Door Specifications
• 8.7.2.10 - Entrances
• 8.7.2.11 - Hoistway Door Locking Devices– Interlocks– Door Restrictors
• 8.7.2.12 - Door Operators
• 8.7.2.13 - Reopening Devises
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 37
What gets Dragged in• Replace Interlocks & Install Restrictor• 8.7.2.11.1 {1201.11a}
• 8.7.2.11.5
Interlocks. Where the alteration consists of the installation of hoistway door interlocks, the installation shall conform to 2.12.1, 2.12.2, 2.12.4 through 2.12.7, and 2.24.8.3.
Restricted Opening of Hoistway Doors or Car Doors of Passenger Elevators. Where a device that restricts the opening of hoistway doors or car doors is altered or installed, the device shall conform to 2.12.5.
4/13/2012 38
What gets Dragged in• Replace Interlocks
– Shall conform to:
Hoistway Door Locking Devices Requirements
2.12.1, 2.12.2, 2.12.4 through 2.12.7,
and 2.24.8.3 - Driving-Machine Brake
• Install Restrictor – Shall conform to:
Hoistway Door Locking Device Requirement
2.12.5
4/13/2012 39
Door Specifications
• 8.7.2.10 - Entrances
• 8.7.2.11 - Hoistway Door Locking Devices– Interlocks– Door Restrictors
• 8.7.2.12 - Door Operators
• 8.7.2.13 - Reopening Devises
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 40
What gets Dragged in• Replace Door Operator• 8.7.2.12 {1201.12}
• Power Operation of Hoistway Doors. Where the alteration consists of the addition of, or alteration to, power opening or power closing of hoistway doors, the installation shall conform to 8.7.2.10.1, 8.7.2.10.2,8.7.2.10.3, and 8.7.2.10.5.
Note: This doesn’t take you right to 2.13
4/13/2012 41
What gets Dragged in• Power Operation of Hoistway Doors
– Shall conform to:– Entrances and Hoistway Openings– 8.7.2.10.1>
– 8.7.2.10.2 – Horizontal Slide-Type Entrances– 8.7.2.10.3 – Vertical Slide-Type Entrances– 8.7.2.10.5 – Marking of Entrance Assemblies
8.7.2.10.1(c) Where an alteration is made to any hoistwayentrance, it shall conform to 2.11.3, 2.11.5, 2.11.7, 2.11.8,and 8.7.2.10.5. The entire installation shall also conformto 2.12 and 2.13.
4/13/2012 42
Door Specifications
• 8.7.2.10 - Entrances
• 8.7.2.11 - Hoistway Door Locking Devices– Interlocks– Door Restrictors
• 8.7.2.12 - Door Operators
• 8.7.2.13 - Reopening Devises
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 43
What gets Dragged in• Replace Door Reopening Device• 8.7.2.13 {1200.5d}
• Door Reopening Device. Where a reopening device for power-operated car doors or gates is altered or added, the following requirements shall apply:(a) requirement 2.13.4 Closing Limitations
(b) requirement 2.13.5 Reopening Device Requirements
(c) when firefighters’ emergency operation is provided, door reopening devices and door closing on Phase I and Phase II shall comply with the requirements applicable at the time of installation of the firefighters’ emergency operation.
4/13/2012 44
What gets Dragged in• Door Reopening Device
– Shall conform to:
2.13.4 Closing Limitations– 2.13.4.1 Where Required– 2.13.4.2 Closing Mechanism
• 2.13.4.2.1 Kinetic Energy• 2.13.4.2.2 Door Travel in the Code Zone Distance• 2.13.4.2.3 Door Force• 2.13.4.2.4 Data Plate
● ●
NORMAL
REDUCED
●
DOOR OPERATOR DATA PLATE
Seconds
Seconds
cdp ●
4/13/2012 45
Cab Work
• 8.7.2.14 - Car Enclosures– 8.7.2.14.1 – New Cab– 8.7.2.14.2 - Cab Alteration– 8.7.2.14.3 – Cab Interiors - USA– 8.7.2.14.4 – Cab Interiors - Canada
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.25.1(b), 8.7.2.26, 8.7.2.27.1 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 46
Cab Work
• 8.7.2.14 - Car Enclosures– 8.7.2.14.1 – New Cab
• the installation shall conform to 2.14, 2.15, and 2.17
– 8.7.2.14.2 – Cab Alteration• (a) through (h) Shell, Lights, Fan, Exits, etc.
– 8.7.2.14.3 – Cab Interiors – USA• (a) through (e) Panels and Flooring required to meet
ASTM E 84, UL 723, or NFPA 255:– (1) flame spread rating of 0 to 25– (2) smoke development of 0 to 450
4/13/2012 47
Cab Work
• 8.7.1.2 (2.14.1.7 – Car Top Railing)2.14.1.7 Railing and Equipment on Top of Cars
2.14.1.7.1 A standard railing conforming to 2.10.2 shall be provided on the
outside ...
• TN-10-791 (look for this in the next edition)
###
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:8.7.1.2 (2.14.1.7 – Car Top Railing) 8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
8.7.2.14.5 Addition of Car Top RailingWhere a car top railing is installed, the installation shall conform to 2.14.1.7. Where conformance to 2.14.1.7 is not possible due to existing overhead conditions, an alternative solution providing equivalency to 2.14.1.7 shall be permitted.
4/13/2012 48
MACHINES & CONTROLS
While we are heading for the Machine Room pick-up the Pocket Guide to
Alterations and a sample Plate.
4/13/2012 49www.CodeDataPlate.com
8.7.1 General RequirementsTRACTION HYDRO
8.7.2 8.7.38.7.2.1 Hoistway 8.7.3.18.7.2.2 Pits 8.7.3.28.7.2.7 Machine room 8.7.3.78.7.2.8 Wiring 8.7.3.88.7.2.10 Entrances 8.7.3.10
8.7.2.10.1 General <<<<8.7.2.10.2 Horizontal Slide <<<<8.7.2.10.3 Vertical Slide <<<<8.7.2.10.4 Swing Type <<<<
8.7.2.11 Hoistway Door 8.7.3.118.7.2.11.1 Interlocks <<<<8.7.2.11.4 Access Sw. (App. R) <<<<8.7.2.11.5 Door Restrictor <<<<
8.7.2.12 Operators 8.7.3.128.7.2.13 Re-opening Device <<<<8.7.2.14 Cabs 8.7.3.13
8.7.2.14.1 New Cab <<<<8.7.2.14.2 Cab Alt. Except panels <<<<8.7.2.14.3 Cab Alt. Interiors only <<<<8.7.2.14.5
8.7.2.15 Frame, Plat. & Guides 8.7.3.148.7.2.16 Load and Class
8.7.2.16.1 Type of Service 8.7.3.178.7.2.16.2 Class of Loading 8.7.3.188.7.2.16.3 Pass on Freight 8.7.3.198.7.2.16.4 Increase Rated Load 8.7.3.20
8.7.2.17 Travel or Speed 8.7.3.228.7.2.18 Safeties 8.7.3.15
Code Data Plate (8.6.1.5) Alteration Pocket Guide
For complete list see A17.1 Sect. 8.7 & App. L
Remove Stop Switch (before b-2003)
TRACTION HYDRO8.7.2.19 Governor 8.7.3.168.7.2.20 Rope Brake, etc.
Hydraulic Jack 8.7.3.23.1Hydraulic Cylinder only 8.7.3.23.3Move Power Unit 8.7.3.23.6Plunger Gripper 8.7.3.23.7Valve & Piping 8.7.3.24
8.7.2.21 Ropes 8.7.3.258.7.2.22 Counterweights 8.7.3.26
8.7.2.22.3 Cwt. Guides <<<<8.7.2.23 Buffers 8.7.3.278.7.2.24 Rails 8.7.3.28
Tank 8.7.3.298.7.2.25 Machines8.7.2.26 Terminal Stopping 8.7.3.308.7.2.27 Control Equipment 8.7.3.31
8.7.2.27.1 Top of Car 8.7.3.31.18.7.2.27.2 Leveling 8.7.3.31.2
Anti-Creep 8.7.3.31.38.7.2.27.3 Power Supply 8.7.3.31.48.7.2.27.4 Controller 8.7.3.31.58.7.2.27.5 Type of Motion 8.7.3.31.68.7.2.27.6 Type of Operation 8.7.3.31.7
Emergency Lowering 8.7.3.31.98.7.2.27.7 Remove Stop Switch* 8.7.3.31.10
8.7.2.28 Emerg. Operations 8.7.3.31.88.7.4 Other Driving Machines8.7.5 Special Applications8.7.6 Escalators & MW8.7.7 Dumbwaiters & ML
CodeDataPlate.com281/257-0516
*A17.1b-2003 and later editions only
4/13/2012 50
Machine Room Work
• Rope Brake8.7.2.20 Ascending Car Overspeed and
Unintended Car Movement Protection
The requirements of 2.19 shall be conformed to where a device for protection against ascending car overspeed and unintended car movement is altered or installed.
###
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 51
Machine Room Work
• Replace DC motor with AC Motor– 8.7.2.25.1 Alterations to Driving Machines
and Sheaves– 8.7.2.25.1(a) – New Machine– 8.7.2.25.1(b) – Alterations to Machine– 8.7.2.25.1(c) – Alteration to Sheave
###
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 52
Machine Room Work
• Control Items– 8.7.2.27.1 – Top-of-Car Operating Device– 8.7.2.27.2 – Car Leveling Device– 8.7.2.27.5 – Change in Type of Motion Control– 8.7.2.28 – Emergency Operations
and Signaling Devices
###
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 53
Other Control Changes
Controllers– 8.7.2.27.3 – Change in Power Supply– 8.7.2.27.4 – Replace Control– 8.7.2.27.5 – Change in Type of Motion Control– 8.7.2.27.6 – Change in Operation Control
###
ALTERATION CODE: ASME A17.1b-2003SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.8, 8.7.2.10.2, 8.7.2.11.1, 8.7.2.11.5, 8.7.2.12, 8.7.2.14.3, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
4/13/2012 54www.CodeDataPlate.com
Note: These 4 requirements are often mixed up.
Control Changes• Power – Supply to controller is altered in type,
phase or voltage (not a new Main Line)
• Controller is replaced without a change to Motion or Operation Control (and this could be a change from relay to microprocessor)
• Type of Motion - such as MG to SSD or VVVF
• Type of Operation – Car Switch to Automatic, Simplex to Duplex or Group
4/13/2012 55www.CodeDataPlate.com
Note: Hydro control change may not require change to fire service.
Control Changes• 8.7.2.28 Emergency Operations
• Emergency Signaling Devices• Emergency or Standby Power• Firefighters Service
• 8.7.3.31.8Emergency Operations• (a) Emergency Signaling Devices• (b) Emergency or Standby Power• (c) Firefighters Service
4/13/2012 56
2.27.2 - Emergency or Standby Power System 2.27.3 - Firefighters’ Emergency Operation:
Automatic Elevators 2.27.4 - Firefighters’ Emergency Operation:
Non- Automatic Elevators 2.27.5 – Automatic Elevators With Designated-
attendant Operation 2.27.6 - Firefighters’ Emergency Operation:
Inspection Operation 2.27.7 - Firefighters’ Emergency Operation:
Operating Procedures 2.27.8 - Switch Keys
2.26.4 - Electrical Equipment and Wiring2.26.5 - System to Monitor and Prevent Automatic Operation of the Elevator With Faulty Door Contact Circuits2.26.6 - Phase Protection of Motors2.26.7 - Installation of Capacitors or Other Devices to Make Electrical Protective Devices Ineffective2.26.8 - Release and Application of Driving-Machine Brakes2.26.9 - Control and Operating Circuits
Terminal Stopping DevicesNormal Terminal Stopping DevicesFinal Terminal Stopping DevicesEmergency Terminal Stopping DeviceEmergency Terminal Speed-Limiting Device
Where Required and FunctionLocation
Inspection Operation Location Switch for Transferring Control of the Elevator
to the Operating Devices Continuous Pressure Type Maximum Speed 0.75 M/S (150 Ft/Min) Used Only by Elevator PersonnelInspection Operation With Open Door Circuits
What gets Dragged inReplacement of a controller
2.25
2.26.1.4 & 2.26.1.5
2.26.4 thru 2.26.9
2.27.2 thru 2.27.8
2.26.4.1 & 2.26.4.2
Change in type of motion control
8.7.2.27.4No change in type of motion control
2.26.4 Electrical Equipment and Wiring
2.26.4.1 All electrical equipment and wiring shall conform to NFPA70 or CSA-C22.1, whichever is applicable.
2.26.4.2 Electrical equipment shall be listed/certified and labeled/marked.
Where a controller for the operation of hoistwaydoors, car doors, or car gates is installed as part of an alteration, all new and modified equipment and wiring shall conform to 2.26.4.1 and 2.26.4.2
Courtesy of Bill Synder
4/13/2012 57
Replacement of a controller
No change in type of motion control
Motion control: that portion of a control system that governs the acceleration, speed, retardation, and stopping of the moving member.
What is a change in the type of motion control?
Courtesy of Bill Synder
Control Changes
4/13/2012 58
Types of Traction Motion Control8.7.2.27.5
AC motor control:control, AC motor, DC injectioncontrol, single speed ACcontrol, two speed ACcontrol, variable voltage, variable frequency (VVVF)control, variable voltage AC (VVAC)
DC motor control: control, dual bridge thyristor convertercontrol, generator fieldcontrol, multivoltagecontrol, rheostaticcontrol, single bridge thyristor converter
Courtesy of Bill Synder
4/13/2012 59Courtesy of Rob Kramer
Work in Progress A17.1-201X
4/13/2012 60
Work in Progress A17.1-201X
Courtesy of Rob Kramer
4/13/2012 61
Replacement of a controller
No change in type of motion control
Now we will replace the controller and change the type
of motion control.
Replace the Motor Generator with Static Drive.
Change in type of motion control
Courtesy of Bill Synder
Control Changes
4/13/2012 62
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Where there is a change in the type of motion control, the installation shall conform to the following:
(a) The protection of the hoistway landing openingsshall conform to 2.11.1 through 2.11.13, 2.12, and 2.13.
Courtesy of Bill Synder
Control Changes
4/13/2012 63
Where there is a change in the type of motion control, the installation shall conform to the following:
(b) Car enclosures and car doors or gates shall conform to 2.14, except that where existing car enclosures and/or car doors or gates are retained, conformance with the following requirements is not required:(1) requirements 2.14.1.3, 2.14.1.5.1, and 2.14.1.8(2) requirements 2.14.2.1, 2.14.2.3, and 2.14.2.4(3) requirement 2.14.3(4) requirements 2.14.4.3 and 2.14.4.6
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Courtesy of Bill Synder
Control Changes
4/13/2012 64
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Where there is a change in the type of motion control, the installation shall conform to the following:
(c) The car safety, the counterweight safety (where provided), and the governor shall conform to 2.17 and 2.18, except that the pitch diameter of speed governor sheaves and governor tension sheaves are not required to conform to 2.18.7.
(d) The capacity and loading shall conform to 2.16.
(e) The terminal stopping devices shall conform to 2.25.
Courtesy of Bill Synder
Control Changes
4/13/2012 65
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Where there is a change in the type of motion control, the installation shall conform to the following:
(f) The operating devices and control equipment shallconform to 2.26. The requirements of 2.26.4.2, 2.26.4.3,and 2.26.4.4 shall not apply to electrical equipmentunchanged by the alteration.
Courtesy of Bill Synder
Control Changes
4/13/2012 66
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Where there is a change in the type of motion control, the installation shall conform to the following:
(g) In jurisdictions not enforcing NBCC, emergency operation and signaling devices shall be provided and shall conform to 2.27. In jurisdictions enforcing NBCC, emergency operation and signaling devices where required by NBCC shall be provided and shall conform to 2.27.
Courtesy of Bill Synder
Control Changes
4/13/2012 67
Replacement of a controller
2.7.2.27.5Change in type of
motion control
Where there is a change in the type of motion control, the installation shall conform to the following:
(h) Car overspeed protection and unintended movementprotection shall conform to 2.19.
What about the platform guard?
2.15.9.2 The guard plate shall have a straight vertical face, extending below the floor surface of the platform, conforming to one of the following:
(a) where the elevator is required to conform to 2.19.2.2(b) the depth of the truck zone, where provided, plus 75 mm (3 in.), but in no case less than 1 220 mm (48 in.)
Courtesy of Bill Synder
Control Changes
4/13/2012 68
Replacement of a controller
2.7.2.27.5Change in type of
motion control
All we had to do was to read what the code requires.
Did we forget about anything?
Courtesy of Bill Synder
Control Changes
4/13/2012 69
Alteration Acceptance Inspection
• 8.10.2.3 – Alterations to Electric Elevators• 8.10.3.3 – Alterations to Hydraulic Elevators
– Also note:
• 8.10.1 - General• 8.10.2 - Electric• 8.10.3 - Hydraulic• 8.10.4 - Escalators• 8.10.5 - Other Equipment
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
4/13/2012 70
8.10 Required Tests
8.10.1.2 Applicability of Inspection and Test Requirements.
Do these words look familiar?Inspections and tests required by 8.10.2 through8.10.5 are to determine that the equipment conformswith the following applicable requirements:
(a) the Code at the time of installation(b) the Code effective as applicable to and for each alteration(c) the ASME A17.3 Code if adopted by AHJ
In A17.1-1996 -1000.2 “ if applicable.”
4/13/2012 72
8.10 Required Alteration Tests
• Traction - 8.10.2.3• 8.10.2.3.1 Alterations shall be
inspected for compliance with the applicable requirements specified in 8.7. Check code data plate for compliance with 8.7.1.8
• Under A17.1-1996 this was Rule 1003.3
• Also see 8.10.2.1 for items not covered by 8.10.2.3.1
• Hydro - 8.10.3.3• 8.10.3.3.1 Alterations shall be
inspected for compliance with the applicable requirements specified in 8.7.Check code data plate for compliance with 8.7.1.8.
• Under A17.1-1996 this was Rule 1006.3
• Also see 8.10.3.1 for items not covered by 8.10.3.3.1
4/13/2012 73
8.10 Required Alteration Tests
Door Operator
4/13/2012 74
8.10 Required Alteration Tests for Alteration to Door Operator
• Hydro - 8.10.3.3.2 {1006.3}(a) Where the alteration consists of the addition
of power operation to the door system (8.7.3.12 {1203.1m}), tests shall be performed as specified in 8.10.3.2.1(a), (h), (i), (j), and (t); 8.10.3.2.3(g); 8.10.3.2.3(r); 8.10.2.2.4(b), (d) through (g); and 8.10.2.2.6.{1002.2h – see Item 1.10 in A17.2}
Red is what was in 1996 code. Black is new in 2000 and later
4/13/2012 75
8.10 Required Alteration Tests for Alteration to Door Operator
• Traction - 8.10.2.3.2 {1003.3}(a) Where the alteration consists of the addition
of power operation to the door system (see 8.7.2.12 {1201.12}), tests shall be performed as specified in 8.10.2.2.1(h), (i), (j), and (t); 8.10.2.2.3(c)(3); 8.10.2.2.3(j) and (w); 8.10.2.2.4(b), and (d) through (g); and 8.10.2.2.6. {1002.2h – Power Operation }
And what happened to (a) Door Reopening Device (2.13.5) (Item 1.1)?
4/13/2012 76
8.10 Required Alteration Tests for Alteration to Door Operator
• Traction - 8.10.2.3.2 (a) Power operation to the door system tests: – 8.10.2.2.1(h) – Door Closing Force Test (in ’96)– 8.10.2.2.1(i) – Door Closing Time Test– 8.10.2.2.1(j) – Door Opening & Zone Tests– 8.10.2.2.1(t) - Door Monitoring Systems– 8.10.2.2.3(c)(3) – Inspection Operation with
open door circuits– 8.10.2.2.3(j) - Car Leveling Devices– 8.10.2.2.3(w) - Door and Gate Equipment
4/13/2012 77
8.10 Required Alteration Tests for Alteration to Door Operator
• Traction - 8.10.2.3.2 (a) Power operation to the door system tests - continued: – 8.10.2.2.4(b) - Hoistway Doors– 8.10.2.2.4(d) - H/W Door Locking Devices– 8.10.2.2.4(e) - Access to Hoistway– 8.10.2.2.4(f) - Power Closing of H/W Doors– 8.10.2.2.4(g) - Sequence Operation– 8.10.2.2.6 - Firefighters’ Emergency
Operation Test
4/13/2012 78
8.10 Required Alteration Tests for Alteration to Door Operator
• 1002.2h – Power Operation of Door System– 112.3a Power Closing (A17.1-1996/7)– Item 1.8 Door Closing Force (30 lbf)
• 8.10.2.2.1(h) – Door Closing Force Test – 2.13.4 Closing Limitations for Power-Operated
Horizontally Sliding Hoistway Doors and Horizontally Sliding Car Doors or Gates
– Item 1.8 Door Closing Force (30 lbf)
4/13/2012 79
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.1(i) – Door Closing Time Test
– 2.13.3 Power Closing per Data Plate 2.13.4.2.4– Item 1.9 Power Closing of Doors or Gates
• 8.10.2.2.1(j) - Power Opening of Doors – (1) Power Opening of Doors (2.13.2)– (2) Leveling Zone & Leveling Speed (2.26.1.6.3)– (3) Inner Landing Zone (2.26.1.6.7)
● ●
NORMAL
REDUCED
●
DOOR OPERATOR DATA PLATE
Seconds
Seconds
cdp ●
4/13/2012 80
A17.1a-2005 Acceptance
• 8.10.2.2.1(j) Category 1
• 8.11.2.2.8 Category 5
• 8.11.2.3.7• 8.11.2.3.8• 8.11.2.3.9
A17.2-2004• Item 1.10.2
Anti-creep
4/13/2012 81
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.1(t) - Door Monitoring Systems
– 2.26.5 - System to Monitor and Prevent Automatic Operation of the Elevator With Faulty Door Contact Circuits
• 8.10.2.2.3(c)(3) – Top of Car Inspection Operation with open door circuits– 2.26.1.5 - Inspection Operation With Open Door
Circuits (Test operation of Bypass Switches on the controller for Car and Hoistway Doors)
4/13/2012 82
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.3(j) - Car Leveling Devices
– 2.26.1.6 - Operation in Leveling or Truck Zone– Item 3.7 - Car Leveling and Anticreep DevicesPeriodic Inspections (no separate Acceptance)
– 3.7.1.1 Electric Elevators– 3.7.1.2 Hydraulic Elevators
• 8.10.2.2.3(w) - Door and Gate Equipment– 2.11, 2.12, and 2.13 - Hoistway Doors – 2.11.1.2 - Emergency Doors
4/13/2012 83
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.3(w) - Door and Gate Equip. (cont.)
– 2.1.1.1.3 and 2.11.15.1 - Hoistway Door Labels– 2.11.11.8 - Door safety retainers, location, and
function– 2.12.2.2 and 2.12.3.2 - Door closed position – 2.11.11.5.8 and 2.11.12.4.8 - Hoistway Door
Hanger– 2.12.2.3, 2.12.2.5, 2.12.3.3, 2.12.3.5, 2.26.2.14,
and 2.26.4.3 - Hoistway Door Locking Device
4/13/2012 84
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.4(b) - Hoistway Doors (2.11)
– (1) test of closed bi-parting doors (2.11.12.4.3 and
2.11.12.4.7)– (2) hoistway door (2.11)
• Item 4.2.3 Acceptance Inspection– Examine hoistway doors...measure the distances
between the hoistway face of the hoistway doors and the car door or gate....
Note: Items are from Inspector Guide A17.2-2004
4/13/2012 85
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.4(d) - Hoistway Door Locking Devices
(2.12.2.3, 2.12.2.5, 2.12.3.3, 2.12.3.5, 2.12.4.3, 2.26.2.14, and 2.26.4.3)
• Item 4.4.3 Acceptance Inspection– …Verify that the interlocks, or the mechanical locks and
electric contacts, are of a type that have been tested and
approved, and are marked for identification…
4/13/2012 86
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.4(e) - Access to Hoistway
– (1) access for maintenance (2.12.6 and 2.12.7)– (2) access for emergency (2.12.6)
• Item 4.5.1 (no unique acceptance inspection)
– (a) Unlocking Devices– (b) Hoistway Access Switches
4/13/2012 87
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.4(f) - Power Closing of Hoistway Doors 2.13.1(type), 2.13.3(horz), and 2.13.4(v/l)
• Item 4.6.3 Acceptance InspectionWhere both a hoistway door and a car door or gate are
opened and/or closed by power, check that the hoistway
door and the car door or gate are
(a) both of the horizontally sliding type; or
(b) both of the vertically sliding type
So then horizontally sliding hoistway doors and vertically sliding car door on the same car won’t pass!
4/13/2012 88
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.4(g) - Sequence Operation – 2.13.6 - Sequence Operation for Power-Operated
Hoistway Doors With Car Doors or Gates– 2.13.3.4 - Power Closing of Vertically Sliding
Hoistway Doors and Vertically Sliding Car Doors or Gates by Momentary Pressure or by Automatic Means
• Item 4.7.1 (no unique acceptance inspection)– (a) hoistway door 2/3 open before car door starts– (b) car door 2/3 closed before hoistway door starts
4/13/2012 89
8.10 New Required Alteration Tests
for Alteration to Door Operator• 8.10.2.2.6 - Firefighters’ Emergency Operation. Verify conformance with 2.27.3 through 2.27.8.
And on Hydro and on Traction (presumably omitted by accident)
• 8.10.2.2.1(a) Door Reopening Device - 2.13.5– Item 1.1.1 (no unique acceptance inspection)
• (a) Mechanical Reopening Device (Safety Edge). • (b) Electronic Reopening Device..• (c) Photoelectric Reopening Device.
4/13/2012 90
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
Door Operation Tests
TN 10-962 (work in progress)8.10.1.1.4 A permanent test record showing the test dates, the requirement number for each test, the name of the person or firm performing the test, inspector’s name, QEI-1 number and certifying organization that witnessed the tests shall be made a permanent part of the maintenance records. (8.6.1.4.1) The test record/tag shall document all applicable acceptance tests shown in the following tables:
4/13/2012 91
8.10 Required Alteration Tests
Machine Alterations
4/13/2012 92
8.10 Required Alteration Tests• Traction - 8.10.2.3.2 (i) Machine
Alteration tests:(i) Where the location of the driving machine has
been changed (8.7.2.25.2), for alterations as described in 8.7.2.25.2(a) (no change in rise), tests shall be performed as specified in 8.10.2.2.2(d), (i), (n), and (v)(3). For alterations as described in 8.7.2.25.2(b) (change in rise), tests shall be performed as specified in 8.10.2.2.
NOTE: These tests apply to change of location
4/13/2012 93
8.10 Required Alteration Tests• Traction - 8.10.2.3.2 (r) Machine
Alteration tests:(r) Where an alteration is made that results in a
new drive machine (see 8.7.2.25.1), tests shall be performed as specified in 8.10.2.2.2(j), (n) through (s), (v), (w), (cc),and (dd); and 8.10.2.2.1(q).
Also see 8.10.2.3.2(t) Change in Type of Motion Control for new motor.
So that’s it for machine, right?
4/13/2012 94
8.10 Required Alteration Tests• NOT SO FAST: How about are made to
other driving machine Components - 8.7.2.25.1(b)
• Traction - 8.10.2.3.2 (h) Machine Alteration tests:(h) Where alterations are made to a driving
machine brake (see 8.7.2.25), tests shall be performed as specified in 8.10.2.2.2(o) and (v)(3).
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
4/13/2012 95
8.10 Required Alteration Tests
Rope Brake
4/13/2012 96
8.10 Required Alteration Tests• Traction - 8.10.2.2.2 (cc) Ascending Car
Overspeed, and Unintended Car Motion Protection(1) Ascending Car Overspeed Protection. The meansto prevent ascending car overspeed shall be inspectedand tested with no load in the car to verify conformancewith 2.19.1.2.(2) Unintended Car Motion. The means to preventunintended car motion shall be inspected and tested toverify conformance with 2.19.2.2.
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
4/13/2012 97
8.10 Required Alteration Tests
Control Alteration
4/13/2012 98
8.10 Required Alteration Tests for Alteration to Controller
• 8.10.2.3.2 Tests shall be performed when the following alterations are made:– (s) Where a controller is installed as part of an
alteration without any change to the type of operation or control (see 8.7.2.27.4), tests shall be performed as specified in 8.10.2.2.1(c), (j), (q), and (t); 8.10.2.2.2(k), (l), (m), (t), (u), (y), (z), (cc), and (dd); and 8.10.2.2.6.
4/13/2012 99
8.10 Required Alteration Tests for Alteration to Controller
• 8.10.2.3.2 Tests shall be performed when the following alterations are made:– (t) Where an alteration is made that results in a
change in the type of motion or operation control (8.7.2.27.5 and 8.7.2.27.6), tests shall be performed as specified in 8.10.2.2.2(l) and (m). All electrical protective devices shall be tested for proper operation.
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
4/13/2012 100
8.10 Required Alteration Tests for Alteration to Controller
• 8.10.2.3.2 Tests shall be performed when the following alterations are made:– (u) Where an alteration is made that results in a new
replacement of a hoistway door, car door, or car gate
controller without any change to the operation or control
[see 8.7.2.27.4(b)], tests shall be performed as specified
in 8.10.2.2.1(i) and (j); and 8.10.2.2.2(l)(1), (l)(2), (l)(3),
and (l)(5).
4/13/2012 101
Electric Elevator - Acceptance Test Tag – DO NOT REMOVE Person or Firm Performing Test: Date:
Witnessed by: QEI #
REQ. # Devices Tested/ Test Results of Tests 8.10.2.2.1(h) Door Closing Force Test 8.10.2.2.1(i) Door Closing Time Test 8.10.2.2.1(j)(1) Door Opening 8.10.2.2.1(j)(2) Leveling Zone and Speed 8.10.2.2.1(j)(3) Inner Landing Zone 8.10.2.2.1(q) Emergency / Standby Power Test 8.10.2.2.2(v) Braking System Test 8.10.2.2.2(y)(3) Winding Drum Machines Slack Rope 8.10.2.2.2(y)(6) W.D. Mach. Final Terminal Stopping 8.10.2.2.2(cc)(a) Emergency Stop 8.10.2.2.2(cc)(3) Traction Limit 8.10.2.2.2(ff) Terminal Stopping Devices Test 8.10.2.2.2(hh) Governors Overspeed Test 8.10.2.2.2(ii) Car Safety Test 8.10.2.2.2(ii)(2) Car Safety Type ‘A’ inertia app. Test 8.10.2.2.2(ii) Counterweight Safety Test 8.10.2.2.2(ii)(2) Cwt Safety Type ‘A’ inertia app. Test 8.10.2.2.2(jj)(1) Ascending Car OS Protection Test 8.10.2.2.2(jj)(2) Unintended Car Movement Test 8.10.2.2.2(mm) Emergency Brake 8.10.2.2.3(d) Top Car Clearance / Refuge Space 8.10.2.2.3(ff) Unexpected Car Movem. (top-of-car) 8.10.2.2.5(c) Car Oil Buffer Test 8.10.2.2.5(c) Counterweight Oil Buffer Test 8.10.2.2.5(l) Unexpected Car Movement (pit) 8.10.2.2.6 Firefighters’ Emergency Operation
Acc
epta
nce
Insp
ectio
n T
ag
4/13/2012 102www.CodeDataPlate.com
Challenges Facing InspectorsNew in 2000 and later editions
• The Inspection Community is stepping up• NAESA has Code Update Seminars, QEI classes and Webinars –
see the Training Calendar• ASME provides a A17.1-1996/A17.1-2000 cross-reference tool• NCEIG Code Reporter• Elevator Bob’s Code Updates
• CodeDataPlate.com solutions:– Code Research – Standard & Custom Code Data Plates– Replacement Plates & Required Signage– Code Data Plate Kits & Inspection Tags– MCP assistance and format consulting
4/13/2012 103www.CodeDataPlate.com
Contact Information
office:281/257-0516cell: 832/239-2513
4/13/2012 104www.CodeDataPlate.com
When is Code Effective?• Date of Contract?• Date of Permit?• Date of Inspection?
If Alteration, What Rules Apply?• Only work done by Elevator Contractor now?
• All alterations since installation?
• Only alterations now part of the installation?
4/13/2012 105
Washington
Edition/Amendment Effective DatesCodeEdition Type StartDate EndDate
ASME A17.1a-2005 1 January 1, 2008 January 1, 2012ASME A17.1b-2003 1 July 1, 2004 December 31, 2007ASME A17.1-1996 1 June 30, 1998 June 30, 2004ASME A17.1-1993 1 March 1, 1995 June 29, 1998ASME A17.1-1990 1 January 1, 1993 February 28, 1995
ASME/ANSI A17.1-1987 1 January 1, 1989 December 31, 1992ANSI/ASME A17.1e-1987 1 December 6, 1987 December 31, 1988ANSI/ASME A17.1a-1985 1 January 10, 1986 December 5, 1987ANSI/ASME A17.1b-1983 1 December 1, 1984 January 9, 1986ANSI/ASME A17.1a-1982 1 March 1, 1984 November 30, 1984ANSI/ASME A17.1-1981 1 July 1, 1982 February 29, 1984
ANSI A17.1b-1973 1 May 15, 1974 June 30, 1982ANSI A17.1a-1972 1 February 25, 1972 May 14, 1974USAS A17.1a-1967 1 December 30, 1967 February 24, 1972
ASA A17.1-1960 1 November 1, 1963 December 29, 1967WAC 296-96 Min. Std. 1 January 1, 1960 October 31, 1963
4/13/2012 106www.CodeDataPlate.com
4/13/2012 107
SECTION 8.9 CODE DATA PLATE (a-2005)Requirement 8.9 contains requirements for all newand existing equipment within the Scope of this Code.8.9.1 Required InformationData plate shall be provided and maintained that shallindicate the Code to be used for inspections and tests(see 8.10.1.2). The data plate shall indicate the Code andedition in effect at the time of installation. The data plateshall also indicate the Code in effect at the time of anyalteration and indicate the applicable requirements of 8.7.8.9.2 LocationThe data plate shall be in plain view, securely attachedto the main line disconnect or on the controller.8.9.3 Material and ConstructionThe data plate shall be of such material and constructionthat the letters and figures stamped, etched, cast,or otherwise applied to the face shall remain permanentlyand readily legible. The height of the letters andfigures shall be not less than 3.2 mm (0.125 in.).
4/13/2012 108
SECTION 8.9 CODE DATA PLATE (2007, a-08 & b-09)Requirement 8.9 contains requirements for all newand existing equipment within the Scope of this Code.8.9.1 Required InformationData plate shall be provided and maintained that shallindicate the Code to be used for inspections and tests(see 8.10.1.2). The data plate shall indicate the Code andedition in effect at the time of installation. The data plateshall also indicate the Code in effect at the time of anyalteration and indicate the applicable requirements of 8.7.8.9.2 LocationThe data plate shall be in plain view, securely attachedto the main line disconnect or on the controller. It shallalso be permitted to locate the data plate in the controlleras long as it is in plain view with the controller door open. An additional data plate shall be installed in thevicinity of the starting switch on the exterior of escalatorsand moving walks 8.9.3 Material and ConstructionThe data plate shall be of such material and constructionthat the letters and figures stamped, etched, cast,or otherwise applied to the face shall remain permanentlyand readily legible. The height of the letters andfigures shall be not less than 3.2 mm (0.125 in.).
(07)
(b)
4/13/2012 109www.CodeDataPlate.com
8.6.1.6.7 Check for any Missing or Damaged Signs and Data Plates• Machine Room
– Brake Plates– Governor Plate– Code Data Plate– Ambient Air Plate– Hydro Data Plates– Warning Signs
• Fire Service Signs
• Hoistway and Pit– Crosshead Data Plate– Rail Lube Instructions– Warning Signs– Safety Plank Plate– Buffer Plate– Counterweight Runby
• Freight & Capacity
4/13/2012 110
● ●
POUNDS F.P.M.
NUMBER OF ROPES: IN.
MANUFACTURED: BY:
RAIL LUBRICATION INSTRUCTIONS:
● ●
RATED BREAKING STRENGTH: POUNDS
the safety for the characteristics of the rail lubricant to be used.
DIAMETER:
RATED SPEED:
COMPLETE CAR WEIGHT:
RATED LOAD:
POUNDS
CROSSHEAD DATA PLATE
codedataplate.com
INSTALLATION CODE: ASME A17.1a-1997
CODE DATA PLATE
#REF!SECT. 8.7 REQUIREMENTS COMPLIED WITH:
8.7.2.11.5, 8.7.2.28.
CODE DATA PLATEINSTALLATION CODE: ANSI A17.1-1978
ALTERATION CODE: ASME A17.1-2000
codedataplate.com
MAXIMUM COUNTERWEIGHT
RUNBY 24"
● ●
NORMAL
REDUCED
●
DOOR OPERATOR DATA PLATE
Seconds
Seconds
cdp ●
● ●
● CDP ●
LOAD RATING: 6000 POUNDS
NUMBER OF SPRINGS: 2
BUFFER MARKING PLATE
STROKE: 2 1/2 INCHES
● ●
● cdp ●
DO NOT LUBRICATE
RAIL LUBRICATION INSTRUCTIONS:
4/13/2012 111www.CodeDataPlate.com
Products
codedataplate.com
INSTALLATION CODE: ASME A17.1a-1997
CODE DATA PLATE
SECT. 8.7 REQUIREMENTS COMPLIED WITH:
CODE DATA PLATE
INSTALLATION CODE: ANSI A17.1-1971
ALTERATION CODE: ASME A17.1-2000
8.7.2.1.5, 8.7.2.8, 8.7.2.11.5, 8.7.2.12, 8.7.2.13, 8.7.2.14.3, 8.7.2.19, 8.7.2.20, 8.7.2.25.1(b), 8.7.2.27.1, 8.7.2.27.2, 8.7.2.27.5, 8.7.2.28
codedataplate.com
#REF!
1200.5d, 1201.3, 1201.10b, 1201.11a, 1201.12, 1202.3c, 1202.4a, 1202.5a, 1202.11, 1202.12a, 1202.12b, 1202.12e, 1202.13
codedataplate.com
1P30777
PART XII RULES COMPLIED WITH:
CODE DATA PLATE
INSTALLATION CODE: NYC BC 1938 - Article 14
ALTERATION CODE: ASME/ANSI A17.1b-1989
● ●
NORMAL
REDUCED
●
DOOR OPERATOR DATA PLATE
Seconds
Seconds
cdp ●
ALTERATION CODE: A17.1-1965 a-1967 -1978
b-1980 a-1982 a-1985 b-1989 a-1997
#REF! 1200.5d 1201.10 1201.11 1201.12 1202.5
1202.7 1202.9 1202.12 1202.13 1202.14nyc-97tr-alt cdp
CODE DATA PLATE
PART XII RULES COMPLIED WITH:
4/13/2012 112
4/13/2012 113Courtesy of Don Rosenberger