-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
1/34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Product Name Confidentiality LevelGSM BSS INTERNALProduct Version
Total 34 pages
GSM BSS Network KPI (Immediate
Assignment Success Rate) OptimizationManual
(For internal use only)
Prepared by GSM&UMTSNetwork PerformanceResearch Department
Wang Fei
Date
2008-06-18
Reviewed by DateReviewed by DateGranted by Date
Huawei Technologies Co., LtdAll rights reserved
2008-10-25 All Rights Reserved Page 1 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
2/34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Revision Record
Date Revision
Version
Change Description Author
2008-06-18 0.8 Draft completed. Wang Fei
2008-07-18 1.0 The document is modified according toreview comments.
Wang Fei
2008-10-25 All Rights Reserved Page 2 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
3/34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
References
Number References Author Date
1 GSM BSS Network KPI (ImmediateAssignment Success Rate) Baseline
Liu Xiuyu 2007-03-10
2008-10-25 All Rights Reserved Page 3 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
4/34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Content1 Overview of the Immediate Assignment Success Rate ..............................................................71.1 Definition ................................................................................................................................. 71.2 Signaling Procedure and Measurement Points ......................................................................81.3 Symptom Description ............................................................................................................. 8
2 Factors Concerning Immediate Assignment Success Rate ........................................................92.1 Signaling Factors .................................................................................................................... 92.2 Factor Analyzing According to the Definition of the KPI......................................................... 92.3 Factors Analysis .................................................................................................................... 10
2.3.1 Equipment Faults ............................................................................................................ 102.3.2 Um Interface Problems ...................................................................................................112.3.3 SDCCH Congestion ........................................................................................................ 112.3.4 MS Problems ..................................................................................................................12
3 Method of Analyzing the Problem of Low Immediate Assignment Success Rate .....................123.1 Process of Analyzing the Problem of Low Immediate Assignment Success Rate ....... ........123.2 Method of Solving the Problem of Low Immediate Assignment Success Rate ....................14
3.2.1 Equipment Faults ............................................................................................................ 14
3.2.2 Um Interface Problem ..................................................................................................... 143.2.3 System Capacity (Congestion) Analysis ........................................................................193.2.4 MS Problem Analysis ...................................................................................................... 23
4 Test Method ............................................................................................................................... 265 Cases of Immediate Assignment Success Rate Optimization ..................................................265.1 Case 1: Decrease in Immediate Assignment Success Rate Because of SDCCH Congestion
Caused by Incorrect LAC Setting ........................................................................................... 265.2 Case 2: SDCCH Congestion Caused by a Burst of Location Updates ................................275.3 Case 3: Low Assignment Success Rate Because the RACH Minimum Access Level Is Set
to 0 ......................................................................................................................................... 285.4 Case 4: Low Immediate Assignment Success Rate in Some Cells Because of MS Error ...29
6 Onsite Information that Needs to Be Obtained .........................................................................33
2008-10-25 All Rights Reserved Page 4 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
5/34
GSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
TablesTable 1 Mapping between formulae and factors..........................................................................10
2008-10-25 All Rights Reserved Page 5 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
6/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
GSM BSS Network KPI (Immediate Assignment
Success Rate) Optimization Manual
Abstract
Key Words: SDCCH, immediate assignment success rate
Abstract: This document provides the procedure for analyzing the
problems about immediate assignment success rate, describes the
troubleshooting procedure, and provides typical cases.Abbreviations:
Abbreviation Full SpellingBSC Base Station Controller BTS Base Tranceiver StationSDCCH Stand-alone Dedicated Control
Channel
2012-12-12 Huawei Technologies Proprietary Page 6 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
7/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
1 Overview of the Immediate Assignment
Success Rate
Immediate assignment success rate indicates the success rate of the MS accessing
the signaling channel. It concerns the procedure from the MS sending a channel required
message to the BTS to the MS sending an establish indication message to the network.
Immediate assignment success rate is a key access counter. It directly reflects the
success rate of the MS accessing the signaling channel and affects the user experience.
The BSC versions concerned in this document are as follows:
BSC32G3BSC32V300R007C01B015
BSC6000BSC6000V900R001
1.1 Definition
The immediate assignment success rate is calculated from traffic statistics. The
recommended formula is as follows:
Immediate Assignment Success Rate = (Successful Immediate
Assignments/Immediate Assignment Requests) x 100%
2012-12-12 Huawei Technologies Proprietary Page 7 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
8/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
1.2 Signaling Procedure and Measurement Points
BSCBTS MSC
Channel REQ
Channl RQD
Channel ACT
Channel ACT ACK
I MMASS CMD
f i rst SABM
UA
EST IND(CMServi ce REQ)
CR(CMP L3 i nformati on)
CC
CMServi ce Accepted
A1
C1
B1
Note:
A1: Immediate Assignment Requests (Channel Requests (Circuit Service))
B1: Immediate Assignment Commands
C1: Successful Immediate Assignments (Call Setup Indications (Circuit Service))
1.3 Symptom Description
If the immediate assignment success rate decreases, the following symptoms may
occur:
Call setup success rate decreases.
2012-12-12 Huawei Technologies Proprietary Page 8 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
9/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Congestion occurs frequently on the SDCCH.
Traffic volume on the TCH decreases.
Short messages cannot be successfully sent.
2 Factors Concerning Immediate Assignment
Success Rate
2.1 Signaling Factors
According to the signaling flow, the factors concerning the immediate assignment
success rate during each phase are as follows:
(1) Random access request phase: whether the small interference signal on the Um
interface is regarded as the random access request by the BSC. Affecting factor:
Um interface problems;
(2) SDCCH assignment phase: whether the SDCCH is available after the random
access request is accepted. Affecting factor: SDCCH congestion;
(3) Channel activation phase: whether the channel activation is successful after the
channel assignment succeeds. Affecting factor: CHAN ACTIV NACK message is
received because of equipment faults during SDCCH activation;
(4) Immediate assignment command phase: whether the timer for the
acknowledgment of the immediate assignment expires. Affecting factor: Um
interface problems;
(5) Link establishment phase: whether the link can be established on the SDCCH
after the immediate assignment command is sent. Affecting factor: MS features.
The following analysis is based on these factors.
2.2 Factor Analyzing According to the Definition of the KPI
As shown in the previous section, the following four factors are related to immediateassignment success rate: Um interface problems, SDCCH congestion, reception of
2012-12-12 Huawei Technologies Proprietary Page 9 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
10/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
CHAN ACTIV NACK because of equipment faults during SDCCH activation, MS
problems.
These factors are related to the definition of the KPI. There are three formulae that
can define the immediate assignment success rate, the mapping between formulae and
factors are as follows:
Table 1 Mapping between formulae and factors
Formula Affecting Factor
Uminterfaceproblems
Receptionof CHANACTIVNACK
becauseof
equipmentfaultsduring
SDCCHactivation
SDCCHcongestion
MSproblems
Immediate Assignment Success Rate= (Successful ImmediateAssignments/Immediate AssignmentRequests) x 100%
Immediate Assignment Success Rate =
(Successful Immediate Assignments/(Immediate Assignment Requests -(Immediate Assignment Commands -Successful Immediate Assignments))) x100%
Immediate Assignment Success Rate= (Successful ImmediateAssignments/Immediate AssignmentCommands) x 100%
2.3 Factors Analysis
2.3.1 Equipment Faults
2.3.1.1 Low Immediate Assignment Success Rate Caused by TRX Faults
Generally, reception of CHAN ACTIV NACK during the SDCCH activation is caused
by equipment faults. If one TRX fails in the cell configured with multiple TRXs, the
immediate assignment may fail or the SDCCH may be congested. If you are sure that the
fault lies in a TRX, replace the faulty TRX. Otherwise, check the cables in the antenna
2012-12-12 Huawei Technologies Proprietary Page 10 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
11/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
system and the VSWR. If the cables are properly connected and the VSWR is normal,
you need to replace the TRX, and then check whether services are normal again.
2.3.2 Um Interface Problems
2.3.2.1 Mistakenly Regarding Interference as Random Access Request
The BTS may mistakenly regard the interference on the Um interface as the random
access signal. This may lead to immediate assignment failure or SDCCH congestion. In
this situation, the interference problem should be solved.
2.3.2.2Channel Immediate Assignment Failure Caused by Coverage Difference
Between BCCH TRX and non-BCCH TRX
In a cell configured with six or more than six TRXs, the combination losses of the
BCCH TRX and non-BCCH TRXs are different, leading to coverage difference. If the
SDCCH is configured on the non-BCCH TRX, a call that is far away from the serving cell
may fail to access the SDCCH when it is assigned to the non-BCCH TRX. Thus, the call
drop may occur.
2.3.3 SDCCH Congestion
2.3.3.1 SDCCH Congestion Caused by Heavy Traffic
For SDCCH congestion caused by heavy traffic, capacity expansion is necessary.
You can also check the parameters concerning location update and SDCCH dynamic
configuration. For SDCCH congestion caused by traffic burst, such as group sending of
short messages and location update at the portal of a tunnel, the problem cannot be
completely solved. You can, however, alleviate the congestion by enabling the functions
such as SDCCH dynamic adjustment.
2.3.3.2 Congestion Caused by Inappropriate Data Configuration
Location area planning: a reasonable location area plan can help alleviate the
SDCCH congestion.
Dynamic SDCCH assignment: the dynamic SDCCH assignment can help
2012-12-12 Huawei Technologies Proprietary Page 11 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
12/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
alleviate SDCCH congestion.
Dual-band network: a reasonable setting of dual-band network parameters (for
example, CRO, CBA, CBQ, and Cell Reselection Hysteresis) can help alleviate SDCCH
congestion.
Check whether the settings of related timers (such as T3101, T3122, T3212, and
T3111) are reasonable.
2.3.4 MS Problems
In some cases, the location updates performed by the MS are abnormal, leading to a
low immediate assignment success rate. These MSs fail to establish a link on the
SDCCH after sending the channel request, causing a low immediate assignment success
rate. For the detailed analyzing method and case study, see case 4 in section 3.
3 Method of Analyzing the Problem of Low
Immediate Assignment Success Rate
3.1 Process of Analyzing the Problem of Low Immediate Assignment
Success Rate
When the immediate assignment success rate becomes low, you should firstly check
the range in which the problem exists, and then find out the factors related to the problem
according to KPI statistical formulae. For details, see section 2.2 "Factor Analyzing
According to the Definition of the KPI". In the case of recommended formula, the general
process of analyzing the problem is as follows:
2012-12-12 Huawei Technologies Proprietary Page 12 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
13/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Start
Analysis of low
immediate assignment
success rate
Check number of
SDCCH activation
failures/timeout
Check
SDCCH
availablity
Check TRX
availability and
TRX alarm
TRX fault or
transmission
failure
Idle interference
band/signaling
analysis
TRX receive
level and quality
analysis
RACH
overload
times
Solve
Interferenc
e problem
SDCCH seizure
success rate
(location update)
Check timersrelated to
location
update
Check SDCCHdynamic
configuration
Traffic volumeper SDCCH
exceeds paln
SDCCH and
TCH traffic
volume
analysis
Incoming andoutgoing
handovers of
the cell
Replan the
location
areas
No
Insufficient system
capacity?
Abnorma
l
Normal
Hardware
expansion
Equipmen
t fault?
Um interface
fault?
Ye
s
Yes
No
Ye
s
Problem
solved?
Yes
End
Find cells with low
immediate assignment
success rate
MS fault?Analyze signaling and
traffic statistics of cells
with problem
Enable CBA
of the cell
For swapped network,
check whether the
problem exists in
ventor's network
No
Locateproblem
and submit
report
Figure 1 Process of analyzing the problem of low immediate assignment success rate
2012-12-12 Huawei Technologies Proprietary Page 13 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
14/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
3.2 Method of Solving the Problem of Low Immediate Assignment Success
Rate
Before analyzing the cause of low immediate assignment success rate, you should
find out the difference between the actual immediate assignment success rate and the
expected value. You should also find out the influence of the problem and the definition of
the specific immediate assignment success rate KPI.
3.2.1 Equipment Faults
This part aims to solve TRX or transmission problems.Firstly, you should check TRX Availability in BSC Measurement and SDCCH
Availability in SDCCH Measurement. Secondly, you should check the number of times
that a NACK message is received or the timer expires during the SDCCH activation. In
this way, you can determine whether the problem is caused by board faults.
You can also check whether hardware is faulty by viewing BTS alarms or by viewing
the hardware state on Site Device Panel of the LMT. You can check the following traffic
statistics for reference:
Cause BSC Level Cell Level
Equipment faults
BSC Measurement -> Accessmeasurement per BSC ->SDCCH Availability per BSCConfigured SDCCHs per BSCAvailable SDCCHs per BSC
Call Measurement -> Channel ActivationMeasurement per Cell -> SDCCHConnection Measurement per Cell ->CHAN ACTIV NACK Messages Sent byBTS in Immediate Assignment Procedure(SDCCH)Channel Activation Timeouts in ImmediateAssignment Procedure (SDCCH)KPI Measurement per Cell -> TCH
Availability
3.2.2 Um Interface Problem
3.2.2.1 Mistakenly Regarding Interference as Random Access Requests
Interference may cause SDCCH congestion, causing low immediate assignment
success rate. Especially in the areas with a small space between BTSs and dense BCCH
frequency planning, the system allocates SDCCH for each signal if a large number of
interference signals are received. Thus, the congestion may occur. In this situation, theimmediate assignment success rate and paging success rate decrease, and the RACH
2012-12-12 Huawei Technologies Proprietary Page 14 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
15/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
may be overloaded. You can locate the problems by analyzing the idle interference bands
and the TRX receive quality during the call.
If the system mistakenly regards the interference as a random access signal and
sends an assignment command, the immediate assignment will fail. You can locate the
problem by analyzing the Chan Req message.
For the SDCCH congestion caused by interference, you can check the following
traffic statistics for reference:
Cause BSC Level Cell Level TRX Level
SDCCHcongestioncaused byinterference
BSC Measurement ->Access measurementper BSC ->Random AccessSuccess Ratio per
BSC
Call Measurement-> Flow ControlMeasurement perCell -> MSG CCCHLOAD IND (RACH)Messages Sent onAbis Interface
MR Measurement ->Analyzed Measurement
of Interference Band perTRX
Receive Quality
Measurement per TRX
For the problem of mistakenly regarding interference as random access
requests, you can locate the problem by performing signaling analysis on the Abis
interface of the cell with worst performance.
If the signaling analysis result shows that the random access signals are all from far
away, for example, the values of TA are higher than 10, sometimes even higher than
20, and the levels are lower than -100 dBm, the random access success rate is high
and the immediate assignment success rate is low, you can infer that the signals are
interference. To restrict the access of interference, reduce MAX TA and increase
RACH Min Access Level.
You can check the following traffic statistics for reference:
Cause BSC Level Cell Level
MistakenlyAccess ofInterferenceon theSDCCH
BSC Measurement ->Access measurementper BSC -> RandomAccess Success Ratioper BSC
Call Measurement -> ImmediateAssignment Measurement per Cell ->Immediate Assignment AnalyzedMeasurement per Cell -> Call SetupIndications Timed OutCall Measurement -> Immediate
Assignment Measurement per Cell ->
Immediate Assignment Analyzed
Measurement per Cell -> Success
Rate of Random Access
2012-12-12 Huawei Technologies Proprietary Page 15 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
16/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Figure 2 shows the contents of a channel required message.
Figure 2 Channel request signaling
Information element description:
1. The meaning ofRandom Access Information (8bits) is as follows:
Table 9.9/3GPP TS 04.08: CHANNEL REQUEST message content
MS codes According to Establishment cause:
bits
8 .... 1
101xxxxx Emergency call
2012-12-12 Huawei Technologies Proprietary Page 16 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
17/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
110xxxxx Call re-establishment; TCH/F was in use, or
TCH/H was in use but the network does not
set NECI bit to 1
011010xx Call re-establishment; TCH/H was in use and the
network sets NECI bit to 1
011011xx Call re-establishment; TCH/H + TCH/H was in use
and the network sets NECI bit to 1
100xxxxx Answer to paging
0010xxxx
0011xxxx See table 9.9a/3GPP TS 04.08
0001xxxx
111xxxxx Originating call and TCH/F is needed, or originating call
and the network does not set NECI bit to 1, or
procedures that can be completed with a SDCCH and the
network does not set NECI bit to 1. note 1
0100xxxx Originating speech call from dual-rate mobile station when
TCH/H
is sufficient and supported by the MS for speech calls and the network
sets NECI bit to 1 note 5
0101xxxx Originating data call from dual-rate mobile station when TCH/His sufficient and supported by the MS for data calls and the network sets
NECI bit to 1 note 5
000xxxxx Location updating and the network does not set NECI bit to 1
0000xxxx Location updating and the network sets NECI bit to 1
0001xxxx Other procedures which can be completed with note 1
an SDCCH and the network sets NECI bit to 1
011110xx One phase packet access with request for single timeslot uplink
01111x0x transmission; one PDCH is needed.01111xx0
01110xxx Single block packet access; one block period on a PDCH is
needed for
two phase packet access or other RR signalling purpose.
01100111 LMU establishment note 2
01100xx0 Reserved for future use
01100x01
01100011 note 2a
2012-12-12 Huawei Technologies Proprietary Page 17 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
18/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
01111111 Reserved for future use. note 2b
NOTE 1: Examples of these procedures are: IMSI detach, Short Message Service (SMS),Supplementary Service management, Location Services.
NOTE 2: If such messages are received by a network, an SDCCH shall be allocated.
NOTE 2a: If such messages are received by a network, an SDCCH may be allocated.
NOTE 2b: This value shall not be used by the mobile station on RACH. If such message is
received by the network, it may be ignored.
2. The value ofAccess Delay indicates the TA.
3. Bits 13, 14, 15, and 16 indicate the RACH level and the number of error bits in thetraining sequence. In this example, the value of bit 13 is 43. This indicates that the
bits followed indicate the AB access level and the number of error bits in the training
sequence. The value of bit 14 is 2. This indicates that the following two bits indicate
the AB access level and the number of error bits in the training sequence. The value
of bit 15 indicates the RACH level (39 120 = 81 dBm).
3.2.2.2 Coverage Difference
If the combination mode of the BCCH TRX and the non-BCCH TRX is different, orthe losses are inconsistent because of different transmit power or other problems, the
assignment on the non-BCCH TRX may fail.
The causes can be classified into three types:
The transmit power of TRXs in the same cell is different.
If concentric cell technology is not applied, the power of different TRXs on the
antenna input port is different because of different uplink losses. This causes inter-TRX
coverage difference. Thus, assignment failure may occur. To solve this problem, check
whether the combiner, divider, CDU, or SCU is properly connected.
Multiple antennae are installed in a cell.
When multiple antennae are installed in a cell, the coverage differences of the
antennae may cause assignment failure. You can solve this problem through engineering
adjustment.
The transmit and receive antennae are not on the same horizontal plane or their
tilts are not the same. You can solve this problem by adjusting the antennae.
2012-12-12 Huawei Technologies Proprietary Page 18 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
19/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
3.2.3System Capacity (Congestion) Analysis
3.2.3.1 Congestion Caused by Heavy Traffic on the SDCCH
Generally, heavy traffic on the SDCCH is caused by frequent location updates. You
can check the rate of the SDCCH being occupied by querying the counter Channel
Requests (Location Updating) and the total number of channel requests. Figure 3
shows the ratios of different kinds of SDCCH requests to the total number of SDCCH
requests on Shanghai Unicom when the traffic is heavy. If the ratios are high, check the
location area planning and the drive test result. If the edges of location areas are
configured in the area with heavy traffic, reconfigure the location areas. In addition, you
can adjust the CHR parameters to reduce location updates. For details, see Case 1.
If the SDCCH congestion rate is high (greater than 5%), the traffic volume on each
SDCCH may have exceeded the limit as planned. You should check the configuration of
the location update and SDCCH dynamic configuration parameters. If the settings of
parameters are reasonable, a hardware capacity expansion is required.
If the congestion rate and traffic volume of the SDCCH are high, but the traffic
volume of the TCH is normal, the SDCCH congestion may be caused by burst traffic. For
the sites along the railway, especially for these near the tunnel portal, the capacity
configured is generally small. When a train passes through or stops, a large number of
location updates occur, which finally lead to SDCCH congestion. In addition, during the
period when the volume of short messages is large, SDCCH congestion may occur. This
problem cannot be completely solved, but you can take some measures to alleviate the
congestion. For example, configure more SDCCHs, or enable the dynamic conversion
between the SDCCH and TCH. For details, see Case 2.
For the configuration of related parameters, see section 3.2.3.2 "Congestion Caused
by Inappropriate Parameter Configuration".
You can check the following traffic statistics for reference:
Cause BSC Level Cell Level
2012-12-12 Huawei Technologies Proprietary Page 19 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
20/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Congestioncaused byheavy trafficon theSDCCH
BSC Measurement ->Access measurementper BSC ->Congestion Ratio on
SDCCH per BSC
Call Measurement -> Immediate AssignmentMeasurement per Cell -> Channel Requests per Cell ->Channel Requests (MOC), Channel Requests (MTC),Channel Requests (Emergency Call), Channel Requests(Call Re-establishment), Channel Requests (LocationUpdating), Channel Requests (Packet Call), ChannelRequests (LMU+Reserved), Channel Requests(Protocol Incompatible)KPI Measurement per Cell -> SDCCH Traffic Volume,
SDCCH Seizure Requests, Failed SDCCH Seizures due
to Busy SDCCH
Figure 3 shows the ratios of different kinds of SDCCH requests to the total number
of SDCCH requests on Shanghai Unicom when the traffic is heavy:
Rati os of Di f f erent Ki nds of SDCCH Requests to the Total Number of SDCCH Requests onShanghai Uni comwhen the Traf f i c i s Heavy
12. 5389.309
0. 055% 0. 030
31. 059
47. 003
0. 001 0. 0060.000%
5.000%
10. 000%
15. 000%20. 000%
25. 000%
30. 000%
35. 000%
40. 000%
45. 000%
50. 000%
A300A
Number
ofSDCCH
requests
(mobile
originated
call)
A300C
Number
ofSDCCH
requests
(mobile
terminated
call)
A300D
Number
ofSDCCH
requests
(emergency
call)
A300E
Number
ofSDCCH
requests(call
re-
establishment)
A300F
Number
ofSDCCH
requests
(location
updating)
A300H
Number
ofSDCCH
requests
(packetcall)
A300I
Number
ofSDCCH
requests(LMU+
Reserved)
A300K
Number
ofSDCCH
requests
(protocol
incompatible)
Rati os of di f ferent ki nds of SDCCH requests
Figure 3 Ratios of different kinds of SDCCH requests to the total number of SDCCHrequests on Shanghai Unicom when the traffic is heavy
Congestion Caused by Inappropriate Parameter Configuration
An inappropriate parameter configuration may lead to the SDCCH congestion.
The parameters related to SDCCH congestion and their configurations are as
follows:
1. CRO: Generally, it is recommended that an MS should not camp on a cell with
high traffic volume or low QoS. The parameters of such cells should be set as follows:
firstly, set PT to 31, so that TO becomes invalid. Secondly, set C2 to the same value as
CRO subtracted from C1 so that the value of C2 is reduced and thus the possibility of
2012-12-12 Huawei Technologies Proprietary Page 20 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
21/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
reselecting this cell is reduced. In addition, network operators can set the CRO according to
the actual conditions. The greater the CRO is, the more difficult it is for an MS to access
the cell.
2. Cell Reselection Hysteresis (CRH): This parameter is used to determine
whether cell reselection is performed between different location areas. This parameter
can prevent frequent location update, thus minimize the possibility of losing paging
messages. Generally, this parameter is set to 6 dB. For dual-band networks in urban
areas not sharing the location areas, this parameter is set to 810 dB.
If the traffic volume in an area is high, and signaling overload occurs frequently,
it is recommend that you set the CRH of the neighboring cells belong to different
LACs under this area to a larger value.
If the overlapping area of the neighbor cells under different location areas is
large, it is recommended that you set the CRH of the cells to a larger value.
If some areas between two neighbor cells under different location areas have
poor coverage, or if most of the MSs in the area (such as highways) move at a
high speed, it is recommended that you set the CRH of the cells to 26 dB.
3. Set the parameters related to SDCCH dynamic adjustment as follows:
Parameter Description
SDCCHDynamicAllocationAllowed
If this parameter is set to YES, the dynamic conversionbetween the SDCCH and the TCH is enabled.
Idle SDCCHThresholdN1
According to the channel assignment algorithm, whenthe number of idle SDCCHs in the cell is smaller thanor equal to the value of this parameter, the systemtries to find a TCHF that can be converted into anSDCCH. This parameter is one of the conditions forthe dynamic conversion from TCHF to SDCCH.
CellSDCCHChannelMaximum
According to the channel assignment algorithm, thesystem determines whether the number of SDCCHs inthe cell after the conversion exceeds the value of CellSDCCH Channel Maximum before initiating thedynamic conversion from TCH to SDCCH. If yes, theconversion is not initiated.
TCH
MinimumRecovery
This parameter specifies the minimum time for the
recovery of a TCH from the SDCCH.
2012-12-12 Huawei Technologies Proprietary Page 21 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
22/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
Time(s)
4. Related timers and their recommended configurations are as follows:
T3101: This timer is used for immediate assignment procedure monitoring.
Reduce the value of this parameter properly to minimize the congestion caused
by dual assignment of the SDCCH. If the length of this timer is too long, the
invalid usage of signaling resources is increased. To enhance the usage of the
signaling resources, you should shorten the length of this timer, especially when
the queuing function is enabled.
T3122: This timer is started by the MS when the MS receives the IMMEDIATE
ASSIGN REJECT message. The MS can send a new channel request message
only after T3122 expires. If the length of T3122 is too short, the MS may send
the channel request message frequently when no system resources are
available. This increases the load on the RACH and CCCH.
T3212: This timer is used for the periodic location update. Increase the length of
this timer properly to reduce the load on the SDCCH brought by periodic
location update.
T3111: This timer delays the deactivation of channels after main signaling links
are disconnected to reserve time for repeated link disconnection. T3111 is
started during the disconnection of both TCH and SDCCH. The value of T3111
must be the same as the value of T3110 at the MS side. Generally, they are set
to 2 seconds. If the length of T3111 is too long, the SDCCH congestion rate is
increased.
5. RACH Min Access Level: If the value of this parameter is too small, much
interference may access the network, thus leading to SDCCH congestion. If the value of
this parameter is too large, it is probable that MSs cannot make the call even though the
signal level is high. This parameter should be set on the basis of the actual receiver
2012-12-12 Huawei Technologies Proprietary Page 22 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
23/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
sensitivity of the BTS, the minimum access level of the MS, and the interference
condition.
6. Late assignment: This function is set at the MSC side. If this function is enabled,
the call is on the SDCCH before the called MS answers. This prolongs the time when the
SDCCH is occupied and thus may cause SDCCH congestion.
7. RXLEV_ACCESS_MIN: If this level is too low, a large number of MSs may access
the network, and SDCCH congestion may occur during call initiation or location update.
In addition, interference signal may be mistakenly regarded as the random access
signals. For details, see Case 3.
8. Tx-integer: When the network traffic is heavy, the success rate of immediate
assignment is low if the sum of S and T is small. Thus, the value of T should be properly
adjusted to make the sum of S and T greater. For details about the value of S, see the
description ofTx-integer.
9. Cell Bar Access (CBA):
0: cell access allowed;
1: cell access prohibited.
Together with CBQ, CBA determines the priority of a cell. For details, see the GSM
04.08 protocol.
CBQ CBA Cell SelectionPriority
Cell ReselectionPriority
0 0 Normal Normal
0 1 Prohibited Prohibited
1 0 Low Normal
1 1 Low Normal
10. Cell Bar Qualify (CBQ): CBQ takes effect during cell selection rather than cell
reselection.
3.2.4 MS Problem Analysis
3.2.4.1 Checking the Problem Symptoms
Objective: to check the problems that exist on site and solve the problems caused by
poor air interface quality and incorrect parameter settings.
2012-12-12 Huawei Technologies Proprietary Page 23 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
24/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
The symptoms are listed as follows:
Symptom 1: The number of failed SDCCH seizures due to timeout is almost equal to
the number of location updating requests minus the number of link establishment
indications for location updating.
Symptom 2: The problem happens discontinuously during both busy hours and idle
hours.
Symptom 3: The call service is normal. Except for low immediate assignment
success rate in a few cells during certain periods, the KPIs and drive test result are
normal, and no call drop complaint is received. Because when an MS fails in location
update, it may try to access other cells or try to access the cell again periodically.
Symptom 4: No interference and no cells with the same BCCH frequency and BSIC
exist.
Symptom 5: No abnormality such as uplink-downlink imbalance exists.
Symptom 6: The result of signaling analysis on the Abis interface shows that the
number of request retransmissions and the retransmission interval of the failed location
updates meet the configuration requirements.
If all the previous symptoms exist, you can infer that the problem is low immediate
assignment success rate caused by abnormal location update.
3.2.4.2 Problem Handling
As the problem of low immediate assignment success rate is caused by some MSs,
and the MSs cannot be located because no layer-3 information is provided in location
update procedure, this problem cannot be solved on the network side currently.
To improve the user satisfaction, do as follows:
(1) Reduce the impact of abnormal MS location updates on the network KPIs.
(2) Communicate thoroughly with customers.
Problem handling:
If any of the previous six symptoms does not exist, initiate the procedures for
network optimization and troubleshooting.
To perform network optimization according to the RSL signaling, do as follows:
1. If the value of TA in the location update signaling is high and the access level is
2012-12-12 Huawei Technologies Proprietary Page 24 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
25/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
low during the time when the problem exists, do as follows:
Adjust the following parameters: Max TA, RACH Min Access Level, and Tx-
integer(increase S and T).
Increase the length of the following timers: T3101, T3122, T3212, and T3111.
Adjust the cell selection priority by setting the value ofCBA and CBQ.
2. For the sites located on the edge of location areas, do as follows to optimize the
location update strategy:
Adjust the parameter Cell Reselection Hysteresis and adjust the cell selection
priority by setting the value ofCBA and CBQ.
3. Reduce the MS retransmission times (recommended value: 1) and reduce the
impact of retransmission on the network KPIs.
Data analysis:
1. For the analysis report of problem location, see the following attachment.
Analysis on Low Immediate Assignment Success Rate Caused by Abnormal MS Location Update-qiuwenfang.rar
Based on the previous analysis, we find that the channel requests received when the
problem occurred were sent by some abnormal MSs, and the BTS responded and
handled the requests correctly. The analysis is based on the uplink and downlink. The
details are described as follows:
2. Uplink channel requests from the MS
(1) When the cell access is prohibited, the immediate assignment success rate of the
cell becomes normal. This indicates that the abnormal location updates are caused by
the MS rather than the interference.(2) The location update requests are with high level, low error rate, and small TA
(except for some sites with wide coverage area). This indicates that the abnormal
location updates are initiated by the MS.
(3) The number of location update requests sent by an MS complies with the settings
of network parameters. This also indicates that the abnormal location updates are
initiated by the MS.
3. Downlink immediate assignment
2012-12-12 Huawei Technologies Proprietary Page 25 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
26/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
(1) The immediate assignment commands are sent correctly, because the values of
T1, T2, and T3 are the same as those in the channel requests.
(2) Call access and the supplementary services such as short message are all
normal. The problem only exists in the SDCCH access related to location update. This
indicates that the immediate assignment commands are sent correctly.
4. Network data comparison (for the swapped offices and the offices with segmental
networking)
By comparing the data before and after swapping (for swapped offices) and the data
of the surrounding cells (for the offices with segmental networking), we find that the
problem also exists in the networks of other companies.
4 Test Method
Immediate assignment success rate is a traffic measurement counter.
As the formulae of this counter in different manufacturers and operators are different
currently, you should record the value of other related counters and choose a proper
formula according to the actual conditions.
5 Cases of Immediate Assignment Success
Rate Optimization
5.1 Case 1: Decrease in Immediate Assignment Success Rate Because of
SDCCH Congestion Caused by Incorrect LAC Setting
Problem description
The SDCCH congestion rate of cell 2 in S1/1/1 configuration was higher than 8%,
and the immediate assignment success rate of that cell was 90%.
Cause analysis and handling
(1) The measurement counters of the TCH and SDCCH shows that the traffic volume on
2012-12-12 Huawei Technologies Proprietary Page 26 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
27/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
the TCH is low, and the traffic volume per cell in busy hours is lower than 2.2 Erl; however,
there are many SDCCH seizure requests (3032 in busy hours), the traffic volume on the
SDCCH is 1.86 Erl, and the congestion rate is higher than 8%.
(2) The SDCCH is mainly occupied by the signaling before the call is established,
the signaling during handover, the signaling for location update in idle mode, and the
short messages.
(3) As the traffic volume on the TCH, the number of TCH seizure requests (318), and
the number of handover requests (146) are all normal, we infer that the high SDCCH
seizure rate may be caused by too frequent location updates or too many short
messages.
(4) The LAC of the cell is 0500, but the LACs of other cells around this cell are all
0520. After the LAC of the cell is changed to 0520, the number of SDCCH seizure
requests becomes 298, the traffic volume on the SDCCH becomes 0.27 Erl, the
congestion rate decreases to 0, and the immediate assignment success rate reaches up
to 95%.
5.2 Case 2: SDCCH Congestion Caused by a Burst of Location Updates
Problem description
The immediate assignment success rate was low in a local network. Traffic statistics
showed that the problem was mainly caused by SDCCH congestion on some sites.
Cause analysis and handling
(1) Traffic statistics shows that the SDCCH is occupied for 300 to 400 times in busy
hours. The congested cells are all in S1/1/1 configuration and each cell is configured with
eight SDCCHs/8. In normal conditions, 300 to 400 times of SDCCH seizures are
acceptable, but SDCCH congestion happens for tens of times in each cell.
(2) Traffic statistics show that most of the SDCCH seizures are caused by location
update. As most of the congested BTSs are located in the intersection areas of two
location areas along the railway, we doubt that the SDCCH congestion may be caused by
2012-12-12 Huawei Technologies Proprietary Page 27 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
28/34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
29/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
and finally causes low assignment access rate.
In addition, the parameter Random Access Error Threshold also has error
restrictions on the access signals.
(4) When RACH Min Access Level and Random Access Error Threshold of all
the cells in module 1 of the BSC in Shantou Unicom are set to different values, the
results are as follows:
When Random Access Error Threshold and RACH Min Access Level are
set to 200 and 1 respectively, the mean immediate assignment success rate of
all the cells is 97.9% an hour later;
When Random Access Error Threshold and RACH Min Access Level are
set to 200 and 0 respectively, the mean immediate assignment success rate of
all the cells is 91.92% an hour later;
When Random Access Error Threshold and RACH Min Access Level are
set to 180 and 1 respectively, the mean immediate assignment success rate of
all the cells is 97.24% three hours later.
After discussing with the customer, we decide to set Random Access Error
Threshold and RACH Min Access Level of all the cells to 180 and 3
respectively. In this way, mean immediate assignment success rate of all the
cells is higher than 98.6%.
5.4 Case 4: Low Immediate Assignment Success Rate in Some Cells
Because of MS Error
Problem description
The personnel on site reported that the immediate assignment success rate of some
cells was low.
Cause analysis and handling
(1) As the problem exists only in some cells, it may be caused by the MS error.
(2) Traffic statistics of the cells with the problem show that the number of link
2012-12-12 Huawei Technologies Proprietary Page 29 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
30/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
establishing failures during location updates is approximately equal to the number of
times that the setup indication timer expires, as shown in the following figure. This
indicates that the SDCCH setup failure is mainly caused by location updates.
(3) The signaling of the cells with problem shows that generally the value of TA is
small and the level is high. This indicates that the problem is not caused by interference.
But after the BSS sends the immediate assignment command and waits for the MS to
access, the uplink signal strength detected by the BTS is always lower than 110 dBm.
This indicates that the MS does not report the link establishing indication and thus
causing the immediate assignment failure.
In addition, we check whether location updates are initiated by a same MS and
whether the number of location updates is in compliance with the network setting. The
following figure shows the signaling captured in the local network. As can be seen, the
2012-12-12 Huawei Technologies Proprietary Page 30 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
31/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
location updates are mainly initiated by a same MS and the maximum number of
retransmissions of the location update request set on the network is five.
The parameters associated to channel request are configured as follows:
2012-12-12 Huawei Technologies Proprietary Page 31 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
32/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
(4) Cell bar access (CBA) status modification test.
After the CBA of a cell is enabled, the system information of the cell will carry a flag
bit. The MSs that receive such system information will not consider that cell during cell
reselection, and the number of location update requests to the neighboring cells
increases.
After the CBA is enabled, the immediate assignment KPIs become better, as shown
in the following figure.
2012-12-12 Huawei Technologies Proprietary Page 32 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
33/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
(5) For a swapping project, check whether the problem exists in the network before
swapping. If the problem existed, then we can infer that the problem is mainly
related to the MS.
6 Onsite Information that Needs to Be
Obtained
1. Traffic statistics of the network during one week before and after the problem
occurred.
BSC32:
(1) All the counters of the Access Capability Measurement 1 and Access
Capability Measurement 2 in BSC Overall Performance Measurement;
(2) All the counters ofReceive Quality Performance Measurement;
(3) All the counters of the SDCCH Assignment Performance Measurementand TCH Assignment Performance Measurement in Channel Assignment
Performance Measurement;
(4) All the counters ofSDCCH Performance Measurement, TCH Performance
Measurement, and Random Access Performance Measurement in Cell
Performance Measurement.
BSC6000:
(1) All the counters ofAccess Measurement per BSC in BSC Measurement;
(2) All the counters ofInterference Band Measurement per TRX and Receive
Quality Measurement per TRX in MR Measurement;
(3) All the counters of Channel Configuration Measurement per Cell in
Channel Measurement;
(4) All the counters of KPI Measurement per Cell, Immediate Assignment
Measurement per Cell, and Flow Control Measurement per Cell in Call
Measurement.
2012-12-12 Huawei Technologies Proprietary Page 33 of 34
-
7/30/2019 116546742 08 GSM BSS Network KPI Immediate Assignment Success Rate Optimization Manual
34/34
GSGSM BSS Network KPI (Immediate Assignment Success Rate) Optimization Manual INTERNAL
2. Data configuration and OMC data operation logs before and after the problem
occurred.
3. Data configuration file and engineering parameters table.
4. Whether the network optimization operations, such as antenna adjustment,
frequency adjustment, and location area adjustment, are performed after the problem
occurred.
5. Alarms generated before and after the problem occurred, including commissioning
alarms.