Download - 1 ENE 428 Microwave Engineering Lecture 11 Excitation of Waveguides and Microwave Resonator
1
ENE 428Microwave Engineering
Lecture 11 Excitation of Waveguides and Microwave Resonator
2
Excitation of WGs-Aperture coupling
WGs can be coupled through small apertures such as for directional couplers and power dividers
(a)
wg1
wg2
coupling aperture
feed wg cavity
(b)
coupling aperture microstrip1
microstrip2
Ground planeer
er er
wg stripline
(c) (d)
3
A small aperture can be represented as an infinitesimal electric and/or magnetic dipole.
Both fields can be represented by their respective polarization currents.
The term ‘small’ implies small relative to an electrical wavelength.
Fig 4.30
4
Electric and magnetic polarization
Aperture shape
e m
Round hole
Rectangular slot
(H across slot)
0 0 0 0ˆ ( ) ( ) ( ),e e nP nE x x y y z ze ))))))))))))))
0 0 0( ) ( ) ( ).m tmP H x x y y z z ))))))))))))))))))))))))))))
e is the electric polarizability of the aperture.m is the magnetic polarizability of the aperture.(x0, y0, z0) are the coordinates of the center of the aperture.
302
3
r 304
3
r
2
16
ld 2
16
ld
5
From Maxwell’s equations, we have
Thus since and has the same role as and , we can define equivalent currents as
and
Electric and magnetic polarization can be related to electric and magnetic current sources, respectively
0 0
0
m
e
E j B M j H j P M
H j D J j E j P J
))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))
))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))
e
M))))))))))))))
J))))))))))))))
0 mj P))))))))))))))
ej P))))))))))))))
eJ j P))))))))))))))))))))))))))))
0 mM j P))))))))))))))))))))))))))))
6
Coupling through an aperture in the broad wall of a wg (1)
Assume that the TE10 mode is incident from z < 0 in the lower guide and the fields coupled to the upper guide will be computed.
y
xaa/20
b
2b
1 2
34
z
y
7
Coupling through an aperture in the broad wall of a wg (2) The incident fields can be written as
The excitation field a the center of the aperture at x = a/2, y = b, z = 0 can be calculated.
10
sin ,
sin .
j zy
j zx
xE A e
aA x
H eZ a
10
,
.
y
x
E A
AH
Z
8
Coupling through an aperture in the broad wall of a wg (3) The equivalent electric and magnetic dipoles for coupling to the fields in the upper guide are
Note that we have excited both an electric and a magnetic dipole.
0
0
10
( ) ( ) ( ),2
( ) ( ) ( ).2
y e
mx
aJ j A x y b z
j A aM x y b z
Z
e
0 0 0( ) ( ) ( ).m tmP H x x y y z z ))))))))))))))))))))))))))))
0 0 0 0( ) ( ) ( ),e ne
P nE x x y y z z ))))))))))))))
e
9
Coupling through an aperture in the broad wall of a wg (4) Let the fields in the upper guide be expressed as
where A+, A- are the unknown amplitudes of the forward and backward traveling waves in the upper guide, respectively.
10
10
sin , 0,
sin , 0,
sin , 0,
sin , 0,
j zy
j zx
j zy
j zx
xE A e for z
a
A xH e for z
Z a
xE A e for z
a
A xH e for z
Z a
10
Coupling through an aperture in the broad wall of a wg (5) By superposition, the total fields in the upper guide due to the electric and magnetic currents can be found forthe forward waves as
and for the backward waves as
where
00 2
10 10 10
1( ) ( ),m
Vn y y x x ej A
A E J H M dvP P Z
e
00 2
10 10 10
1( ) ( ),m
Vn y y x x ej A
A E J H M dvP P Z
e
1010
.ab
PZ
11
Microwave Resonator A resonator is a device or system that exhibitsresonance or resonant behavior, that is, it naturallyนoscillates at some frequencies , called its resonant frequency , with greater amplitude than at others.
Resonators are used to either generate waves of sp ecific frequencies or to select specific frequencies fro
m a signal.
The operation of microwave resonators is very similar to that of the lumped-element resonators of circuit theory.
12
Basic characteristics of series RLC resonant circuits (1)
The input impedance is
The complex power delivered to the resonator is
AC
R L
CZin
I
1.inZ R j L j
C
21 1 1( ).
2 2inP VI I R j L jC
13
Basic characteristics of series RLC resonant circuits (2) The power dissipated by the resistor, R, is
The average magnetic energy stored in the inductor, L, is
The average electric energy stored in the capacitor, C, is
Resonance occurs when the average stored magnetic and electric energies are equal, thus
21.
2lossP I R
21.
4mW I L
2 2
2
1 1 1.
4 4e cW V C IC
2.
12
lossin
PZ R
I
14
The quality factor, Q, is a measure of the loss of a resonant circuit. At resonance,
Lower loss implies a higher Q
the behavior of the input impedance near its resonant frequency can be shown as
01
LC
0
2.in
RQZ R j
15
A series resonator with loss can be modeled as a lossless resonator 0 is replaced with a complex effective resonant frequency.
Then Zin can be shown as
This useful procedure is applied for low loss resonators by adding the loss effect to the lossless input impedance.
0 0 1 .2
j
Q
02 ( ).inZ j L
16
Basic characteristics of parallel RLC resonant circuits (1)
The input impedance is
The complex power delivered to the resonator is
AC RL CZin
I
11 1
.inZ j CR j L
21 1 1( ).
2 2inj
P VI V j CR L
17
Basic characteristics of parallel RLC resonant circuits (2) The power dissipated by the resistor, R, is
The average magnetic energy stored in the inductor, L, is
The average electric energy stored in the capacitor, C, is
Resonance occurs when the average stored magnetic and electric energies are equal, thus
21
.2loss
VP
R
2 2
2
1 1 1.
4 4m LW I L VL
21.
4eW V C
2.
12
lossin
PZ R
I
18
The quality factor, Q, of the parallel resonant circuit At resonance,
Q increases as R increases
the behavior of the input impedance near its resonant frequency can be shown as
01
LC
0
.1 2 1 2 /in
R RZ
j RC jQ
19
A parallel resonator with loss can be modeled as a lossless resonator. 0 is replaced with a complex effective resonant frequency.
Then Zin can be shown as
0 0 1 .2
j
Q
0
1.
2 ( )inZj C
20
Loaded and unloaded Q
An unloaded Q is a characteristic of the resonant circuit itself.
A loaded quality factor QL is a characteristic of the resonant circuit coupled with other circuitry.
The effective resistance is the combination of R and the load resistor RL.
RL
Resonant circuit Q
21
The external quality factor, Qe, is defined.
Then the loaded Q can be expressed as
0
0
eL
Lfor series circuits
RQ
Rfor parallel circuits
L
1 1 1.
L eQ Q Q
22
Transmission line resonators: Short-circuited /2 line (1)
The input impedance is
0 0
tanh tantanh( ) .
1 tan tanhin
l j lZ Z j l Z
j l l
ZinZ0,,
l
23
Transmission line resonators: Short-circuited /2 line (2) For a small loss TL, we can assume l << 1 so tanl l. Now let = 0+ , where is small. Then, assume a TEM line,
For = 0, we have
or
0 .l
p p p
l ll
v v v
00 0
0 0
( / )( )
1 ( / )in
l jZ Z Z l j
j l
2 .inZ R j L
24
Transmission line resonators: Short-circuited /2 line (3) This resonator resonates for = 0 (l = /2) and its input impedance is
Resonance occurs for l = n/2, n = 1, 2, 3, …
The Q of this resonator can be found as
0 .inZ R Z l
0 .2 2
LQ
R l
25
Transmission line resonators: Short-circuited /4 line (1) The input impedance is
Assume tanhl l for small loss, it gives
This result is of the same form as the impedance of a parallel RLC circuit
0
1 tanh cot.
tanh cotin
j l lZ Z
l j l
0 00
0
0
/ 2 ).
/ 2 )( )
2
in
l j l ZZ Z
l jl j
1.
12
inZj C
R
26
Transmission line resonators: Short-circuited /4 line (2) This resonator resonates for = 0 (l = /4) and its input impedance is
The Q of this resonator can be found as
0 .inZ
Z Rl
0 .4 2
Q RCl