dlp projector - b&h photo video. logo options. hdmi link settings

73
User manual DLP ® Projector

Upload: vanbao

Post on 16-Apr-2018

225 views

Category:

Documents


3 download

TRANSCRIPT

Page 1: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

User manual

DLP® Projector

Page 2: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English2

TablE of ConTEnTs

safETY ............................................................................................... 4

Important Safety Instruction....................................................................................................... 43D Safety Information ................................................................................................................ 5Copyright ................................................................................................................................... 6Disclaimer .................................................................................................................................. 6Trademark Recognition ............................................................................................................. 6FCC ........................................................................................................................................... 7Declaration of Conformity for EU countries ............................................................................... 7WEEE ........................................................................................................................................ 7

InTRoDUCTIon .................................................................................. 8

Package Overview..................................................................................................................... 8Standard accessories ................................................................................................................ 8Optional accessories ................................................................................................................. 8Product Overview ...................................................................................................................... 9Connections.............................................................................................................................. 10Keypad ..................................................................................................................................... 11Remote control ......................................................................................................................... 12

sETUP anD InsTallaTIon ............................................................. 13

Installing the projector .............................................................................................................. 13Connecting sources to the projector ......................................................................................... 14Adjusting the projector image ................................................................................................... 15Remote setup ........................................................................................................................... 16

UsInG THE PRoJECToR .................................................................. 18

Powering on / off the projector.................................................................................................. 18Selecting an input source ......................................................................................................... 20Menu navigation and features .................................................................................................. 21OSD Menu tree......................................................................................................................... 22Image menu.............................................................................................................................. 28Image advanced menu ............................................................................................................. 30Image advanced DARBEE menu ............................................................................................. 32Display menu ............................................................................................................................ 33Display 3D menu ...................................................................................................................... 36Setup menu .............................................................................................................................. 38Setup audio settings menu ....................................................................................................... 40Setup security menu ................................................................................................................. 41Setup advanced menu.............................................................................................................. 43Options menu ........................................................................................................................... 44

Page 3: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 3

Options menu ........................................................................................................................... 46Options HDMI link settings menu ............................................................................................. 48Options remote settings menu.................................................................................................. 503D Setup................................................................................................................................... 53

maInTEnanCE .................................................................................. 54

Replacing the lamp ................................................................................................................... 54Replacing the lamp (continued) ................................................................................................ 55Installing and cleaning the dust filter ........................................................................................ 56

aDDITIonal InfoRmaTIon ............................................................ 57

Compatible resolutions ............................................................................................................. 57Image size and projection distance .......................................................................................... 58Projector dimensions and ceiling mount installation ................................................................. 59IR remote codes ....................................................................................................................... 60Using the Help button ............................................................................................................... 62Troubleshooting ........................................................................................................................ 65Warning indicators .................................................................................................................... 67Specifications ........................................................................................................................... 69Optoma global offices ............................................................................................................... 70DARBEEVISION, INC. ............................................................................................................. 71

Page 4: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English4

safETY

The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Please follow all warnings, precautions and maintenance as recommended in this user's guide.

Important safety InstructionDo not block any ventilation openings. To ensure reliable operation of the projector and to protect from �over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow.

To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. Do not �install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat.

Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short �out parts that could result in fire or electric shock.

Do not use under the following conditions: �In extremely hot, cold or humid environments. ±

(i) Ensure that the ambient room temperature is within 5°C ~ 40°C

(ii) Relative humidity is 10% ~ 85%

In areas susceptible to excessive dust and dirt. ±

Near any appliance generating a strong magnetic field. ±

In direct sunlight. ±

Do not use the projector in places where flammable gases or explosives gases may be present in the �atmosphere. The lamp inside the projector becomes very hot during operation and the gases my ignite and result in a fire.

Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be �(but not limited to):

Unit has been dropped. ±

Power supply cord or plug has been damaged. ±

Liquid has been spilled on to the projector. ±

Projector has been exposed to rain or moisture. ±

Something has fallen in the projector or something is loose inside. ±

Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the �projector may become damaged.

Do not block the light coming out of the projector lens when in operation. The light will heat the object �and my melt, cause burns or start a fire.

Please do not open or disassemble the projector as this may cause electric shock. �

Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous �voltages or other hazards. Please call Optoma before you send the unit for repair.

See projector enclosure for safety related markings. �

The unit should only be repaired by appropriate service personnel. �

Page 5: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 5

Only use attachments/accessories specified by the manufacturer. �

Do not look into straight into the projector lens during operation. The bright light may harm your eyes. �

When replacing the lamp, please allow the unit to cool down. Follow instructions as described on pages �54-55.

This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows �warning messages.

Reset the "Lamp Reset" function from the on-screen display "Options|Lamp Settings" menu after �replacing the lamp module (refer to page 47).

When switching the projector off, please ensure the cooling cycle has been completed before �disconnecting power. Allow 90 seconds for the projector to cool down.

When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show �on the screen. Please contact your local reseller or service center to change the lamp as soon as possible.

Turn off and unplug the power plug from the AC outlet before cleaning the product. �

Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners, �waxes or solvents to clean the unit.

Disconnect the power plug from AC outlet if the product is not being used for a long period of time. �

When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has beennotee: replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages 54-55.

Do not setup the projector in places where it might be subjected to vibration or shock. �

Do not touch the lens with bare hands �

Remove battery/batteries from remote control before storage. If the battery/batteries are left in the �remote for long periods, they may leak.

Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it can �adversely affect the quality of the projector performance.

Please follow the correct projector orientation installation as non standard installation may affect the �projector performance.

Use a power strip and or surge protector. As power outages and brown-outs can KILL devices � .

3D safety InformationPlease follow all warnings and precautions as recommended before you or your child use the 3D function.

Warning

Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be closely supervised when viewing these images.

Photosensitive seizure Warning and other Health Risks

Some viewers may experience an epileptic seizure or stroke when exposed to certain flashing images or �lights contained in certain Projector pictures or video games. If you suffer from, or have a family history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.

Even those without a personal or family history of epilepsy or stroke may have an undiagnosed condition �that can cause photosensitive epileptic seizures.

Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or �under the influence of alcohol should avoid utilizing the unit's 3D functionality.

If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a �medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions; (9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults to experience these symptoms. Parents should monitor their children and ask whether they are experiencing these symptoms.

Page 6: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English6

Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye �strain and decreased postural stability. It is recommended that users take frequent breaks to lessen the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the above symptoms, immediately discontinue use of this device and do not resume using it for at least thirty minutes after the symptoms have subsided.

Watching 3D projection while sitting too close to the screen for an extended period of time may �damage your eyesight. The ideal viewing distance should be at least three times the screen height. It is recommended that the viewer's eyes are level with the screen.

Watching 3D projection while wearing 3D glasses for an extended period of time may cause a �headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D projection and rest.

Do not use the 3D glasses for any other purpose than for watching 3D projection. �

Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles, �etc.) may be physically harmful to you and may weaken your eyesight.

Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your �3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run into, knocked down, broken or fallen over.

CopyrightThis publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

© Copyright 2015

DisclaimerThe information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark RecognitionKensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

DLP , DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments.

All other product names used in this manual are the properties of their respective owners and areAcknowledged.

DARBEE is a trademark by Darbee Products, Inc.

MHL, Mobile High-Definition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing, LLC.

Page 7: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 7

fCCThis device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. �

Increase the separation between the device and receiver. �

Connect the device into an outlet on a circuit different from that to which the receiver is connected. �

Consult the dealer or an experienced radio/television technician for help. �

noticee: shielded cablesAll connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Caution

Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector.

operation Conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference received, including interference that may cause undesired operation.

noticee: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

Remarque l'intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

Declaration of Conformity for EU countriesEMC Directive 2004/108/EC (including amendments) �

Low Voltage Directive 2006/95/EC �

R & TTE Directive 1999/5/EC (if product has RF function) �

WEEE

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.

Page 8: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English8

InTRoDUCTIon

Package overviewCarefully unpack and verify that you have the items listed below under standard accessories. Some of the items under optional accessories may not be available depending on the model, specification and your region of purchase. Please check with your place of purchase. Some accessories may vary from region to region.

The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

standard accessories

Carry bag

optional accessories

Optional accessories vary depending on model, specification and region.notee:

Projector Remote control 2x aaa batteries Power lead

Documentation

CD User Manual

Warranty Card*

Basic User Manual

ON OFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

Source Re-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2 Video YPbPr

VGa cable HDmI cable

* For European warranty Information, please visit www.optomaeurope.com.notee:

Page 9: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 9

InTRoDUCTIon

Product overview

8 109 1113

127

31 2 54

7 6

Do not block projector inlet or outlet air vents.notee: (*) optional accessory varies depending on model, specification, and region.

no Item no Item1. Lens 8. Zoom Lever2. IR Receiver 9. Focus Ring3. Keypad 10. Lamp Cover4. Input / Output 11. Ventilation (outlet)5. Power Socket 12. KensingtonTM Lock Port6. Speaker 13. Ventilation (inlet)7. Tilt-Adjustment Feet

Page 10: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English10

InTRoDUCTIon

Connections

32 4

9 8 67 5

1

Remote mouse requires special remote control.notee:

no Item no Item1. USB Power Out (5V 0.9A) Connector 6. MOUSE / SERVICE Connector2. 12V Out Connector 7. HDMI 2 Connector3. 3D Sync Out (5V) Connector 8. Audio Out Connector4. HDMI 1 / MHL Connector 9. Security Bar5. Power Socket

Page 11: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 11

InTRoDUCTIon

Keypad

1 2

11

6

5

10 789

3 4

no Item no Item1. Source 7. Temp LED2. Enter 8. Power3. Keystone Correction 9. On/Standby LED4. Re-Sync 10. Lamp LED5. Help 11. Menu6. Four Directional Select Keys

Page 12: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English12

InTRoDUCTIon

Remote control

ON OFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

Source Re-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2 Video YPbPr

1

3

2

4

5

6

7

8

11

12

13

14

15

16

17

18

19

20

21

23

22

24

25

27

26

9

10

no Item no Item1. Power On 15. User 32. User 2 16. Contrast3. User 1 17. Display Mode4. Brightness 18. Aspect Ratio5. Keystone 19. 3D Menu On / Off6. Mute 20. Sleep Timer7. DB (Dynamic Black) 21. Volume +8. Source 22. Re-Sync9. Enter 23. Four Directional Select Keys

10. Menu 24. Volume -11. HDMI1 25. HDMI212. VGA1 (not supported) 26. YPbPr (not supported)13. VGA2 (not supported) 27. Video (not supported)14. Power Off

Some keys may have no function for models that do not support these features.notee:

Page 13: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 13

sETUP anD InsTallaTIon

Installing the projectorYour projector is designed to be installed in one of four possible positions.

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Table mount front Ceiling mount front

Table mount rear Ceiling mount rear

Projector should be placed flat on a surface and 90 degrees / perpendicular to the to the screen.

How to determine projector location for a given screen size, � please refer to distance table on page 58.

How to determine screen size for a given distance, � please refer to distance table on page 58.

The further away the projector is placed from the screen the projected image size increases and vertical notee: offset also increases proportionally.

ImPoRTanTT! Do not operate the projector in any orientation other that table top or ceiling mount. The projector should be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard installation advise please contact Optoma.

Page 14: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English14

sETUP anD InsTallaTIon

Connecting sources to the projector

MOLEX

1

79

2

3

5 4

8

6

no Item no Item1. 3D Emitter Cable 6. HDMI Dongle2. HDMI Cable 7. USB Power Cable3. MHL Cable 8. Audio Out Cable4. Power Cord 9. 12V DC Jack5. USB Cable (mouse control)

Page 15: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 15

sETUP anD InsTallaTIon

adjusting the projector imageImage heightThe projector is equipped with elevator feet for adjusting the image height.

Locate the adjustable foot you wish to adjust on the underside of the projector.1. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.2.

Tilt-Adjustment Feet

Tilt-Adjustment Ring

Zoom and focus

To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease �the projected image size.

To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and �legible.

Focus Ring

Zoom Lever

The projector will focus at a distance of 1.5m to 10m.notee:

Page 16: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English16

sETUP anD InsTallaTIon

Remote setupInstalling / replacing the batteriesTwo AAA size batteries are supplied for the remote control.

Remove the battery cover on the back of the remote control.1. Insert AAA batteries in the battery compartment as illustrated.2. Replace back cover on remote control.3.

Replace only with the same or equivalent type batteries.notee:

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

Do not mix batteries of different types. Different types of batteries have different characteristics. �

Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or �cause chemical leakage in old batteries.

Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact �with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

The batteries supplied with this product may have a shorter life expectancy due to storage conditions. �

If you will not be using the remote control for an extended period of time, remove the batteries. �

When you dispose of the batteries, you must obey the law in the relative area or country. �

Effective rangeInfra-Red (IR) remote control sensor is located on the top side and front side of the projector. Ensure to hold the remote control at an angle within 30 degrees perpendicular to the projector’s IR remote control sensor to function correctly. The distance between the remote control and the sensor should not be longer than 6 meters (~ 20 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector �that might obstruct the infra-red beam.

Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps �directly.

Please keep the remote controller away from fluorescent lamps for over 2 meters or the remote �controller might become malfunction.

If the remote control is closed to Inverter-Type fluorescent lamps, it might become ineffective from time �to time.

If the remote control and the projector are within a very short distance, the remote control might �become ineffective.

When you aim at the screen, the effective distance is less than 5 meters from the remote control to the �screen and reflecting the IR beams back to the projector. However, the effective range might change according to screens.

Page 17: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 17

sETUP anD InsTallaTIon

ONOFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

SourceRe-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2VideoYPbPr

ON

OFF

Menu

VGA1

HDMI1

User2

ContrastAspect ratioDB

Volume

Source

Re-sync

User1

BrightnessKeystone

Mute

User3Mode

3DSleep Timer

Volume

HDMI2VGA2Video

YPbPr

Approx. ±15°

Approx. ±15°

Page 18: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English18

UsInG THE PRoJECToR

Powering on / off the projector

ON OFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

Source Re-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2 Video YPbPr

or

Powering onSecurely connect the power lead and signal/source cable. When connected, the On/Standby LED will 1. turn red.Turn on the projector by pressing the 2. " " either on the projector keypad or the remote control.A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing 3. green or blue.

The first time the projector is turned on, you will be prompted to select the preferred language, projectionnotee: orientation, and other settings.

Page 19: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 19

UsInG THE PRoJECToR

Powering off

Turn off the projector by pressing the 1. " " button on the projector keypad or the “ ” button on the remote control.The following message will be displayed:2.

Power Off?Press Power key again

Press the 3. " " button on the projector keypad or the “ ” button on the remote control again to confirm,

otherwise the message will disappear after 15 seconds. When you press the " " or “ ” button for the second time, the projector will shut down.The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/4. Standby LED will flash green or blue. When the On/Standby LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button again to turn on the projector.Disconnect the power lead from the electrical outlet and the projector.5.

It is not recommended that the projector is turned on immediately, right after a power off procedure.notee:

Page 20: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English20

UsInG THE PRoJECToR

selecting an input sourceTurn on the connected source that you want to display on the screen, such as computer, notebook, video player, etc. The projector will automatically detect the source. If multiple sources are connected, push the Source button on the projector keypad or the remote control to select the desired input.

ON OFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

Source Re-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2 Video YPbPr

or

Page 21: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 21

UsInG THE PRoJECToR

menu navigation and featuresThe projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source.

To open the OSD menu, press "Menu" on the remote control or the projector keyboard.1.

When OSD is displayed, use 2. keys to select any item in the main menu. While making a selection on a particular page, press or "Enter" key to enter sub menu.

Use 3. keys to select the desired item in the sub menu and then press or "Enter" key to view further settings. Adjust the settings by using keys.

Select the next item to be adjusted in the sub menu and adjust as described above.4.

Press "Enter" or "Menu" to confirm, and the screen will return to the main menu.5.

To exit, press "Menu" again. The OSD menu will close and the projector will automatically save the 6. new settings.

Display Mode

Brightness

Contrast

Sharpness

Color

Tin t

Advanced

Cinema

ImaGE

SettingsSub Menu

Main Menu

Page 22: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English22

UsInG THE PRoJECToR

osD menu tree

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Image

Display Mode

Cinema

Reference

Game

Vivid [Default]

Bright

3D

User

ISF Day

ISF Night

Brightness -50~50

Contrast -50~50

Sharpness -50~50 [Default: 0]

Color -50~50 [Default: 0]

Tint 1~15

Advanced

Gamma

Film

Video

Graphics

Standard

BrilliantColorTM 1 ~ 10

Dynamic Black

Off.On

[Default: Cinema], notee: other modes are off.

Color Temp.

Warm

Standard

Cool

Cold

Color Matching

Red

Hue -50~50

Saturation -50~50

Gain -50~50

Green

Hue -50~50

Saturation -50~50

Gain -50~50

Blue

Hue -50~50

Saturation -50~50

Gain -50~50

Cyan

Hue -50~50

Saturation -50~50

Gain -50~50

Magenta

Hue -50~50

Saturation -50~50

Gain -50~50

Page 23: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 23

UsInG THE PRoJECToR

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Image

Advanced

Color Matching

Yellow

Hue -50~50

Saturation -50~50

Gain -50~50

White

Red -50~50

Green -50~50

Blue -50~50

Reset Yes / No [Default: No]

Exit

DARBEE

Mode

Hi-Def 0~120%

Gaming 0~120%

Full Pop 0~120%

Off

Demo mode

Split Screen

Swipe Screen

OffExit

Reset Yes/ No [Default: No]Exit

Display

Format

4:3

16:9 [Default]

LBX

Native

SuperWide

Edge Mask 0~5 [Default: 0]

Zoom -5~25 [Default: 0]

Image ShiftH Right / Left (Icon

in the center) -100~+100 [Default: 0]

V Up / Down (Icon in the center) -100~+100 [Default: 0]

H Keystone -40~+40 [Default: 0]

V Keystone -40~+40 [Default: 0]

Four CornerTop-Left / Top-Right / Bottom-Left / Bottom-Right (ICONS)

Four Corner Reset

Yes

No [Default]

3D

3D Mode

Off [Default]

DLP-Link

VESA 3D

3D Format

Auto [Default]

SBS

Top and Bottom

Frame Sequential

3D→2D

3D [Default]

L

R

Page 24: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English24

UsInG THE PRoJECToR

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Display3D

3D Sync. InvertOn

Off [Default]

Exit

Exit

Setup

Language

English [Default]

Deutsch

Français

Italiano

Español

Português

Svenska

Nederland

Norsk

Dansk

Polski

Русский

Suomi

Ελληνικά

Magyar

Čeština

يبرع繁體中文

簡体中文

日本語한국어

ไทย

Türkçe

Farsi

Vietnamese

Romanian

Indonesian

Projection

[Default]

Menu Location

[Default]

Page 25: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 25

UsInG THE PRoJECToR

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Setup

Audio Settings

Internal SpeakerOn [Default]

Off

MuteOn

Off [Default]

Volume 0-10 [Default: 5]

Exit

Security

SecurityOn

Off [Default]

Security Timer

Month 0~12 [Default: 0]

Day 0~30 [Default: 0]

Hour 0~24 [Default: 0]

Exit

Change Password

Exit

Advanced

Logo

Default [Default]

Neutral

User

Logo capture

Exit

Exit

Options

Input SourceHDMI1 / MHL [Default]

HDMI2

Source LockOn

Off [Default]

High AltitudeOn

Off [Default]

Information Hide

OnOff [Default]notee: The Warning and Power off message will not be hidden.

Keypad LockOn

Off [Default]

Test Pattern

None [Default]

Grid

White Pattern

IR Function

All [Default]

Front

TopOffnotee: “All” and “Off” can be only selected in Standby mode.

Page 26: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English26

UsInG THE PRoJECToR

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Options

12V Trigger

Off [Default]

On

Auto 3D

USB Power

Off [Default]

On

Auto

Background Color

Black [Default]

Red

Blue

Green

White

Lamp Settings

Lamp Hours 0~9999 [Default: 0]notee: Display only.

Lamp ReminderOn [Default]

Off

Lamp Mode

Bright [Default]

Eco.

Dynamic

Lamp ResetYes

No [Default]

Exit

HDMI Link Settings

HDMI LinkOff [Default]

On

Inclusive of TVYes

No [Default]

Power On Link

Mutual

PJ→Device

Device→PJ [Default]

Power Off LinkOff [Default]

On

Exit

Remote Settings

USER 1

[Default: DARBEE] Color Settings

Color Temp.

Gamma

HDMI Link

Test Pattern

AV Mute

DARBEE

USER 2

[Default: Color Temp] Color Settings

Color Temp.

Gamma

HDMI Link

Test Pattern

AV Mute

DARBEE

Page 27: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 27

UsInG THE PRoJECToR

main menu sub menu sub menu 2 sub menu 3 sub menu 4 Values

Options

Remote SettingsUSER 3

[Default: Gamma] Color Settings

Color Temp.

Gamma

HDMI Link

Test Pattern

AV Mute

DARBEE

Exit

Advanced

Direct Power OnOn

Off [Default]

Auto Power Off (min.)

0-180 [Default: 20]notee: One step is 5 minutes.

Sleep Timer (min.)

0-990 [Default: 0]notee: One step is 30 minutes.Always On [Default: Unchecked]notee: “Always On” is a check box type parameter.

Power Mode (Standby)

Active

Eco. [Default]

Exit

ResetCurrent [Default]

All

notee:

If the Signal setting is set to Automatic, the Phase, frequency items are grayed out. If the “Signal” �setting is set to a specific input source, the phase, frequency items will appear for user to manually tune and saved in settings.

The “LAMP RESET” in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service �mode. The Projection Hours in service mode will not be reset.

When you made the changes on the “IR Function”, “Projection”, or “Keypad Lock” function, a �confirmation message will appear on the screen. Select “Yes” to save the settings.

Each display mode can be adjusted and saved the value. �

In 3D timing mode, the zoom/edge mask will be disabled to prevent from image break. �

Page 28: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English28

UsInG THE PRoJECToR

Image menu

Reset

Exit

Display Mode

Brightness

Contrast

Sharpness

Color

Tin t

Advanced

Cinema

ImaGE

Display mode

There are many factory presets optimized for various types of images.

Cinema

Reference

Game

Bright

User

Display Mode

Vivid

Cinema: Use this mode for home movie theatre. �

Reference: This mode is intended to reproduce, as close as possible, the image the way the movie �director intended. Color, color temperature, brightness, contrast and gamma settings are all configured to standard reference levels.

Game: Use this mode for playing video games. �

Vivid: Optimized to produce strikingly bright colorful images. �

Bright: Maximum brightness from PC input. �

3D: To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device �has a 120 Hz signal output quad buffered graphics card and a 3D Player installed.

User: Memorize user’s settings. �

Page 29: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 29

UsInG THE PRoJECToR

ISF Day: Optimize the image with the ISF Day mode to be perfectly calibrated and high picture quality. �

ISF Night: Optimize the image with the ISF Night mode to be perfectly calibrated and high picture quality. �brightness

Adjust the brightness of the image.

Brightness

Press the � to darken image.

Press the � to lighten the image.Contrast

Contrast

The contrast controls the degree of difference between the lightest and darkest parts of the picture.

Press the � to decrease the contrast.

Press the � to increase the contrast.sharpness

Adjust the sharpness of the image.

Sharpness

Press the � to decrease the sharpness.

Press the � to increase the sharpness.Color

Adjust a video image from black and white to fully saturated color.

Color

Press the � to decrease the amount of saturation in the image.

Press the � to increase the amount of saturation in the image.Tint

Adjust the color balance of red and green.

Tint

Press the � to increase the amount of green in the image.

Press the � to increase the amount of red in the image.Reset

Choose "Yes" to return the factory default settings for "IMAGE".

Reset

No Yes

Exit

Choose "Exit" to exit the menu.

Page 30: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English30

UsInG THE PRoJECToR

Image advanced menu

Dynamic Black

ImaGE

Exit

advanced

Gamma

Color Temp.

Film

Color Matching

Off

Gamma

This allows you to set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to optimize your image output.

Gamma

Film

Film: For home theater. �

Video: For video or TV source. �

Graphics: For PC / Photo source. �

Standard: For standardized setting. �

Press the � or to choose your preferred gamma.brilliantColorTm

This adjustable item utilizes a new color-processing algorithm and enhancements to enable higher brightness while providing true, more vibrant colors in picture.

Press the � to stronger enhance the image.

Press the � to less enhance the image.Dynamic black

Dynamic Black enables the projector to automatically optimize the brightness of the display during dark/light movie scenes to be shown in incredible detail. Choose “On” or “Off” to enable or disable this feature.

Color Temp.

Press the or to select a color temperature from Warm, Standard, Cool, or Cold.

Color Temp.

Warm

Page 31: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 31

UsInG THE PRoJECToR

Color matching

Press the into the next menu and then use , , , or to select the item.

Color Matching

Red

Green

Blue

White Reset

Exit

Yellow

Magenta

Cyan

Red/Green/Blue/Cyan/Magenta/Yellow/White � : Use or to adjust Hue, Saturation, or Gain Colors.

Hue

Exit

Saturation

Gain

Red

Hue

Exit

Saturation

Gain

Green

Hue

Exit

Saturation

Gain

Blue

Hue

Exit

Saturation

Gain

Cyan

Hue

Exit

Saturation

Gain

Magenta

Hue

Exit

Saturation

Gain

Yellow

Red

Exit

Green

Blue

White

Reset

Choose “ Reset” to return the factory default settings for color adjustments.

Exit

Choose “Exit” to exit the menu.

Page 32: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English32

UsInG THE PRoJECToR

Image advanced DaRbEE menuUse this mode to project enhanced video quality from an HDMI video source.

Mode Off

Level

Demo Mode Off

Exit

mode

Choose your preferred DARBEE mode between the following options:

Hi-Def: The least aggressive form of the algorithm. Suitable for high quality content like Blu-ray video. �

Gaming: Moderately aggressive form of the algorithm. Suitable for computer generated content. �

Full Pop: Most aggressive form of the algorithm. Suitable especially for low-resolution or low-quality �video sources in order to improve the video quality.

Off: Switch off the DARBEE mode. �

After you have chosen your preferred DARBEE mode, use the Level option to adjust the mode value.notee: Demo mode

Allows to check the difference between the original image and the DARBEE image. Press the or to choose your preferred screen view for Demo mode. The available options include split screen and swipe screen.

Split Screen: View the original image and DARBEE image in a split screen. �

Swipe Screen: View the original image and DARBEE image by swiping the screen. �

Off: Demo mode is off. �Exit

Choose “Exit” to exit the menu.

Page 33: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 33

UsInG THE PRoJECToR

Display menu

Format

DIsPlaY

Exit

Zoom

H Keystone

Edge Mask

Image Shift

V Keystone

Four Corner

Four Corner Reset

format

Press the or to choose your desired aspect ratio between 4:3, 16:9, LBX, Native, SuperWide.

Format

4:3 � : This format is for 4:3 input sources.

16:9: This format is for 16:9 input sources, like HDTV and � DVD enhanced for Wide screen TV.

LBX: This format is for non-16x9, letterbox source and for users who use external 16x9 lens to display �2.35:1 aspect ratio using full resolution.

Native: This format displays the original image without any scaling. �

SuperWide: This mode scales 2.35:1 sources to fill 100% of image height to remove black bars. (The �left and right side of image will be cropped).

Detailed informations about LBX mode:notee:

Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image will not �look right when displaying image in 16:9 mode. In this situation, please try to use the 4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image in 16:9 display. For this type of content, you can use LBX mode to fill the image on the 16:9 display.

If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1 content �(include Anamorphic DVD and HDTV film source) that supports anamorphic wide is enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp power and vertical resolution are fully utilized.

Page 34: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English34

UsInG THE PRoJECToR

1080P scaling table:

16 e: 9 screen 480i/p 576i/p 1080i/p 720p PC4x3 Scale to 1440x1080.

16x9 Scale to 1920x1080.lbX Scale to 1920x1440, then get the central 1920x1080 image to display.

native mode 1:1 mapping centered. No scaling will be made; the image is displayed with the resolution based on input source.

superWide First scales to 2534x1426 (132% Enlarge), then displays the central image in 1920x1080 screen format.

notee: Use this format for not subtitled 2.35:1 video source to fulfill 100% of 1080p DMD.

Edge mask

Use this function to remove the video encoding noise on the edge of video source.

Edge Mask

notee:

Each I/O has different setting of “Edge Mask”. �

“Edge Mask” and “Zoom” cannot work at the same time. �Zoom

Press the � to reduce the size of an image.

Press the � to magnify an image on the projection screen.

Zoom

Image shift

Press the into the next menu as below and then use the , , , or to select item.

Image Shift

H

V

H: Press the � to shift the projected image position horizontally.

V: Press the � to shift the projected image position vertically.

H Keystone

Press the or to adjust image distortion horizontally and make a squarer image.

H Keystone

Page 35: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 35

UsInG THE PRoJECToR

V Keystone

Press the or to adjust image distortion vertically and make a squarer image.

V Keystone

four Corner

Compensate for image distortion by adjusting one corner at a time.

Four Corner

Four Corner1. Use "Menu" to start.2. Use "Four Corner" menu to choose one corner and press "Enter" to confirm.3. Use the ▲,▼,◄, or ► to move the angle and press "Enter" to confirm.

Four Corner

Four Corner Four Corner

When Four Corner is adjusted, Format/Edge Mask/Zoom/Image Shift will grey out. They will be available notee: when Four Corner is reset.

four Corner Reset

Choose “Yes” to return the factory default settings for “Four Corner Reset”.

Page 36: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English36

UsInG THE PRoJECToR

Display 3D menu

3D Mode

DIsPlaY

Exit

3D Format

3D Sync. Invert Off

Auto

Off

3D mode

Use this option to disable the 3D function or select the appropriate the 3D function.

Off: � Select "Off" to turn off 3D mode.

DLP-Link: Select "DLP-Link" to use optimized settings for DLP Link 3D Glasses. �

VESA 3D: Select “VESA 3D” to use optimized setting for VESA 3D Glasses. �

3D Mode

Off

DLP - Link

VESA 3D

3D format

Use this option to select the appropriate 3D format content.

Auto: When a 3D identification signal is detected, the 3D format is selected automatically. �

SBS: Display 3D signal in “Side-by-Side” format. �

Top and Bottom: Display 3D signal in “Top and Bottom” format. �

Frame Sequential: Display 3D signal in “Frame Sequential” format. �notee:

“3D Format” is only supported on 3D Timing on page � 57.

“3D Format” is only supported on non-HDMI 1.4a 3D timing. �

3D Format

Auto

3D 2D

Use this option to specify how the 3D content should appear on the screen.

3D: Display 3D signal. �

L (Left): Display the left frame of 3D content. �

R (Right): Display the right frame of 3D content. �

Page 37: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 37

UsInG THE PRoJECToR

3D sync. Invert

Use this option to enable/disable the 3D sync invert function.

Press the "On" to invert left and right frame contents. �

Press the "Off" for default frame contents. �

3D Sync. Invert

Off On

Exit

Choose "Exit" to exit the menu.

Page 38: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English38

UsInG THE PRoJECToR

setup menu

Language

sETUP

Exit

English

Projection

Menu Location

Security

Audio Settings

Advanced

language

Choose the multilingual OSD menu. Press into the sub menu and then use the , , , or key to select your preferred language. Press "Enter" to finalize the selection.

Language

Exit

Projection

Projection

Exit

� FrontThis is the default selection. The image is projected straight on the screen.

� RearWhen selected, the image will appear reversed.

� Front-CeilingWhen selected, the image will turn upside down.

� Rear-Ceiling

Page 39: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 39

UsInG THE PRoJECToR

When selected, the image will appear reversed in upside down position.

Apply projector?

No Yes

Rear-Desktop and Rear-Ceiling are to be used with a translucent screen.notee:

menu location

Choose the menu location on the display screen.

Menu Locat ion

Exit

Exit

Choose "Exit" to exit the menu.

Page 40: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English40

UsInG THE PRoJECToR

setup audio settings menu

sETUP

Exit

Off

audio settings

Mute

Volume

OnInternal Speaker

Internal speaker

Choose “On” or “Off” to turn on or off the internal speaker.

mute

Use this option to temporarily turn off the sound.

Off

Mute

On

Choose the "On" to turn mute on. �

Choose the "Off" to turn mute off. �

“Mute” function affects both internal and external speaker volume.notee:

Volume

Adjust the volume level.

Volume

Press the � to decrease the volume.

Press the � to increase the volume.Exit

Choose "Exit" to exit the menu.

Page 41: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 41

UsInG THE PRoJECToR

setup security menu

Security

sETUP

Exit

Off

security

Security Timer

Change Password

security

Enable this function to prompt for a password before using the projector.

On: Choose "On" to use security verification when the turning on the projector. �

Off: Choose "Off" to be able to switch on the projector without password verification. �

Security

Off On

security TimerCan be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this time has elapsed you will be requested to enter your password again.

Month

Exit

Security Timer

Day

Hour

Page 42: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English42

UsInG THE PRoJECToR

Change PasswordChange the password.

First time � :Press the "Enter" key to set the password.1. The password has to be 4 digits. 2. Use number button on the remote control or on-screen numeric keypad to enter your new password 3. and then press the "Enter" key to confirm your password.

Change Password � : (If your remote does not have a number keypad, please use the arrows to change each digit of the password, then press the “Enter” key to confirm).Press the "Enter" key to input old password.1. Use the number button or on-screen numeric keypad to enter the current password and then press the 2. "Enter" key to confirm. Enter new password (4 digits in length) using the number buttons on the remote control, then press 3. the "Enter" key to confirm.Enter the new password again and press the "Enter" key to confirm.4.

If the incorrect password is entered 3 times, the projector will automatically shut down.

If you have forgotten your password, please contact your local office for support.

The password default value is "1234" (first time).notee:

REMOTE

Enter Security Code (4 digits)

Exit

Choose "Exit" to exit the menu.

Page 43: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 43

UsInG THE PRoJECToR

setup advanced menu

Logo

sETUP

Exit

advanced

Default

Logo Capture

logo

Use this function to set the desired startup screen. If changes are made, they will take effect the next time the projector is powered on.

Logo

Default

Default: The default startup screen. �

Neutral: Logo is not displayed on startup screen. �

User: Use stored picture from “Logo Capture” function. �logo Capture

Press to capture an image of the picture currently displayed on the screen.

Logo Capture

Processing...

For a successful logo capture, ensure that the on-screen image does not exceed the projector nativenotee: resolution. (1080p: 1920x1080).

Exit

Choose "Exit" to exit the menu.

Page 44: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English44

UsInG THE PRoJECToR

options menu

Off

Input Source

Source Lock

High Altitude

Information Hide

Keypad Lock

Test Pattern

oPTIons

Off

Off

Off

None

IR Function All

12V Trigger Off

Input source

Use this option to enable/disable input sources. Press the to enter the sub menu and select which sources you require. Press the "Enter" key to finalize the selection. The projector will only search for inputs that are enabled.

Exit

Input Source

source lock

Use this function to let the projector to search for current input only or any input signals.

On: � The projector will only search current input connection.

Off: The projector will search for other signals if the current input signal is lost. �

Input SourceSource Lock

Off On

High altitude

When "On" is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.

High Altitude

Off On

Information Hide

Enable this function to hide the information message.

On: Choose "On" to hide the info message. �

Off: Choose "Off" to show the "searching" message. �

Information Hide

Off On

Page 45: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 45

UsInG THE PRoJECToR

Keypad lock

When the keypad lock function is "On", the Keypad will be locked. However, the projector can be operated by the remote control. By selecting "Off", you will be able to reuse the Keypad.

Keypad Lock

Off On

No Yes

Apply Keypad Lock?

Test Pattern

Display a test pattern. The available options are Grid, White Pattern and None.

Test Pattern

None

IR function

Set the IR function setting.

All: The projector can be operated by the remote control from front or top IR receiver. �

Front: The projector can be operated by the remote control from front IR receiver. �

Top: The projector can be operated by the remote control from top IR receiver. �

Off: The projector can’t be operated by the remote control from front or top IR receiver. � By selecting “Off”, you will be able to use the Keypad keys.

IR Function

On

No Yes

Apply IR Function?

notee:

“Front” and “Top” cannot be selected in standby mode. �

IR mode can be switched to “NVIDIA 3D Vision” once implemented and verified by NVIDIA. �12V Trigger

Use this function to enable or disable the trigger.

ReservedIR_IN & detect

GND

Page 46: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English46

UsInG THE PRoJECToR

options menu

Background Color Black

Lamp Settings

HDMI Link Settings

Remote Settings

Advanced

Reset

Exit

oPTIons

USB Power Off

Usb Power

Enable or disable the USB power port function.

On: Power over USB port. �

Off: Power over HDMI/MHL port. �

Auto: MHL gets priority over USB with USB being the default power source. �background Color

Press the or to select a "Black", "Red", "Blue", "Green", or "White" screen when no signal is available.

Background Color

Black

Page 47: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 47

UsInG THE PRoJECToR

options lamp settings menu

oPTIonslamp settings

Lamp Hours

Lamp Reminder

Exit

Off

Lamp Mode

Lamp Reset

Bright

lamp Hours

Display the projection time.

lamp Reminder

Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement of lamp.

Lamp Reminder

Off On

lamp mode

Set the lamp mode setting.

Bright: � Increase the brightness.

Eco.: � Dim the projector lamp which will lower power consumption and extend the lamp life.

Dynamic: Dim the lamp power which will be based on brightness level of the content and adjust lamp �power consumption between 100% and 30% dynamically. The lamp life will be extended.

Lamp Mode

Bright

lamp Reset

Resets the lamp hour counter after replacing the lamp.

No Yes

Lamp Reset

Exit

Choose "Exit" to exit the menu.

notee: When ambient temperature is over � 40°C during operation, the projector will switch to Eco automatically.The “Lamp Mode” can be independently set for 2D and 3D. �

Page 48: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English48

UsInG THE PRoJECToR

options HDmI link settings menu

oPTIonsHDmI link settings

HDMI Link

Exit

Off

Inclusive of TV

Power On Link

Power Off Link

Yes

Mutual

Off

Using HDmI link

When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you can control �them on same Power On or Power Off status using the HDMI Link control feature on the projector’s OSD.

This lets one device or multiple devices in a group Power On or Power Off via HDMI Link Feature. �

In a typical configuration, your DVD player may be connected to the projector through an amplifier or �home theater system.

HDmI link

Enable/Disable the HDMI Link function. The Inclusive TV, Power on Link, and Power off Link options will only available if the setting.

HDMI Link

Off On

Inclusive of TV

If the setting is set to “Yes”, both TV and projector will be automatically turned off at the same time. To prevent both devices to be turned off at the same time, set the setting to “No”.

Inclusive of TV

No Yes

Power on link

CEC power on command:

Mutual: Both projector and CEC device will be turned on simultaneously. �

PJ -> Device: The CEC device will be turned on only after the projector is switched on. �

Device -> PJ: The projector will be switched on only after the CEC device is turned on. �

Power On Link

Mutual

Press the � into the next menu and then use the or to select “Mutual”, “PJ -> Device”, “Device -> PJ” item.

Page 49: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 49

UsInG THE PRoJECToR

Power off link

If the setting is set to “On”, both HDMI Link and projector will be automatically turned off at the same time. Set to “Off”, both HDMI Link and projector will be not automatically turned off at the same time.

Power Off Link

Off On

Exit

Choose “Exit” to exit the menu.

Page 50: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English50

UsInG THE PRoJECToR

options remote settings menu

oPTIonsRemote settings

User 1

User 2

User 3

DARBEE

Gamma

Exit

Color Temp.

UsER 1

Assign the default function for USER 1. The default value is “DARBEE”.

User 1

DARBEE

Press the � into the next menu and then use the or the to select “Color Settings”, “Color Temp.”, “Gamma”, “HDMI Link”, “Test Pattern”, “AV Mute”, “DARBEE” item.

UsER 2

Assign the default function for USER 2. The default value is “Color Temp.”.

User 2

Color Temp.

Press the � into the next menu and then use the or the to select “Color Settings”, “Color Temp.”, “Gamma”, “HDMI Link”, “Test Pattern”, “AV Mute”, “DARBEE” item.

UsER 3

Assign the default function for USER 3. The default value is “Gamma”.

User 3

Gamma

Press the � into the next menu and then use the or the to select “Color Settings”, “Color Temp.”, “Gamma”, “HDMI Link”, “Test Pattern”, “AV Mute”, “DARBEE” item.

Page 51: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 51

UsInG THE PRoJECToR

options advanced menu

oPTIonsadvanced

Off

Exit

Direct Power On

Auto Power Off (min)

Sleep Timer (min)

Power Mode (Standby) Eco.

Direct Power on

Choose "On" to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without pressing the " " key on the projector keypad or on the remote control.

Direct Power On

Off On

auto Power off (min)

Set the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes).

Press the � to decrease the timer interval.

Press the � to increase the timer interval.

Auto Power Off (min)

notee:

The value of sleep timer will be reset to zero after the projector is powered off. �

The projector will automatically power off when the countdown has finished. The default setting is 20 minutes. �

sleep Timer (min)

Sets the countdown timer interval. The countdown timer will start, with or without a signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes).

Press the � to decrease the timer interval.

Press the � to increase the timer interval.

Sleep Timer (min)

Always on

Exit

Page 52: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English52

UsInG THE PRoJECToR

Power mode (standby)

Set the power mode setting.

Active: Return to normal standby. �

Eco.: Save power dissipation further < 0.5W. �

Power Mode (Standby)

Active Eco.

Exit

Choose "Exit" to exit the menu.

Page 53: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 53

UsInG THE PRoJECToR

3D setupTurn on your projector.1. Connect your 3D source. For example, 3D Blu ray, Games console, PC, Set top box, etc.2. Ensure you have inserted 3D content or selected the 3D channel.3. Turn on your 3D glasses. Please refer to the 3D glasses user manual on how to operate the 3D 4. glasses.Your projector will automatically display 3D from a 3D Blu-ray. For 3D via a set top box or PC, you will 5. be required to adjust the settings in the 3D menu.

for 3D via blu ray3D will automatically be displayed.

Menu > "Display" > "3D" > "3D Mode" > "DLP Link" �

for 3D via a PC or set top box3D will not be displayed automatically. Depending on the 3D content the image will either be displayed side by side or top and bottom. Please refer to the following table.

sbs sbsTop and bottom

Top and bottom

For side by side images, select "SBS" in the menu. Menu > "Display" > "3D" > "3D Format" > "SBS". �

For top and bottom images, select "top and bottom" in the menu. Menu > "Display" > "3D" > "3D �Format" > "Top and bottom".If the 3D image does not look correct, you may also be required to adjust the 3D sync invert. Turn this on if the image looks odd. Menu > "Display" > "3D" > "3D Sync Invert" > "On".

If input video is normal 2D, please press “3D” and switch to “Auto”. If “SBS” mode is active, 2D videonotee: content will not be displayed correctly. Please change back to “Auto” when 3D via a PC only works with certain resolutions. Please check the compatibility on page 57.

Page 54: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English54

maInTEnanCE

Replacing the lampThe projector automatically detects the lamp life. When the lamp life is nearing the end of use, a warning message will appear on the screen.

Lamp Warning

Lamp life exceeded.

When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.

Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used to prevent any loose parts from falling out of projector.

Warning: Lamp compartment is hot! Allow it to cool down before changing lamp!

Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.

Page 55: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 55

maInTEnanCE

Replacing the lamp (continued)

6

5

3

1

2

7

4

Procedure:

Switch off the power to the projector by pressing the "1. " button on the remote control or the projector keypad.

Allow the projector to cool down for at least 30 minutes.2.

Disconnect the power cord.3.

Unscrew the screw on the cover. 4. 1

Open the cover. 5. 2

Lift up the lamp handle. 6. 3

Press both sides, then lift up and remove the lamp cord. 7. 4

Unscrew the screw on the lamp module. 8. 5

Lift up the lamp handle 9. 6 and remove the lamp module carefully. 7

To replace the lamp module, reverse the previous steps.10.

Turn on the projector and reset the lamp timer.11. Lamp Reset: (i) Press "Menu" 12. (ii) Select "OPTIONS" (iii) Select "Lamp Settings" (iv) Select "Lamp Reset" (v) Select "Yes".

notee:

The screw on the lamp cover and the lamp cannot be removed. �The projector cannot be turned on if the lamp cover has not been placed back on the projector. �Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean �the lamp module if it was accidentally touched.

Page 56: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English56

maInTEnanCE

Installing and cleaning the dust filterInstalling the dust filter

Dust filters are only required/supplied in the selected regions with excessive dust.notee:

Cleaning the dust filterWe recommend you to clean the dust filter every three months. Clean it more often if the projector is used in a dusty environment.

Procedure:

Switch off the power to the projector by pressing 1. the " " button on the remote control or the projector keypad.

Disconnect the power cord.2.

Remove the dust filter carefully.3.

Clean or replace the dust filter.4. To install the dust filter, reverse the previous steps.5.

1

2

Page 57: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 57

aDDITIonal InfoRmaTIon

Compatible resolutions

Digital compatibility

b0/Established Timing b0/standard Timing b0/Detail Timing b1/Video mode b1/Detail Timing

720x400 @ 70Hz 1280x720 @ 60Hz Native timing: 640x480p @ 60Hz 720x480p @ 60Hz

640x480 @ 60Hz 1280x800 @ 60Hz XGA: 1024x768 @ 60Hz 720x480p @ 60Hz 1280x720p @ 60Hz

640x480 @ 67Hz 1280x1024 @ 60Hz WXGA: 1280x800 @ 60Hz 1280x720p @ 60Hz 1366x768 @ 60Hz

640x480 @ 72Hz 1400x1050 @ 60Hz 1080P: 1920x1080 @ 60Hz 1920x1080i @ 60Hz 1920x1080i @ 50Hz

640x480 @ 75Hz 1600x1200 @ 60Hz 720(1440)x480i @ 60Hz 1920x1080p @ 60Hz

800x600 @ 56Hz 1920x1080p @ 60Hz

800x600 @ 60Hz 1440x900 @60Hz 720x576p @ 50Hz

800x600 @ 72Hz 1280x720 @ 120Hz 1280x720p @ 50Hz

800x600 @ 75Hz 1024x768 @ 120Hz 1920x1080i @ 50Hz

832x624 @ 75Hz 720(1440)x576i @ 50Hz

1024x768 @ 60Hz 1920x1080p @ 50Hz

1024x768 @ 70Hz 1920x1080p @ 24Hz

1024x768 @ 75Hz 1920x1080p @ 30Hz

1280x1024 @ 75Hz

1152x870 @ 75Hz

True 3D video compatibility

Input resolution

HDMI 1.4a 3D Input

Input timing

1280x720P @ 50Hz Top - and - Bottom

1280x720P @ 60Hz Top - and - Bottom

1280x720P @ 50Hz Frame packing

1280x720P @ 60Hz Frame packing

1920x1080i @50 Hz Side- by-Side (Half)

1920x1080i @60 Hz Side- by-Side (Half)

1920x1080P @24 Hz Top - and- Bottom

1920x1080P @24 Hz Frame packing

HDMI 1.3

1920x1080i @ 50Hz

Side-by-Side(Half) SBS mode is on1920x1080i @ 60Hz

1280x720P @50Hz

1280x720P @60Hz

1920x1080i @ 50Hz

Top-and-Bottom TAB mode is on1920x1080i @ 60Hz

1280x720P @50Hz

1280x720P @60Hz

480i 1024x768 @ 120Hz HQFS 3D format is Frame sequential

576i 1280x720 @120Hz

notee:

If 3D input is 1080p@24Hz, the DMD should replay with integral multiple with 3D mode. �Support for NVIDIA 3DTV Play if there is no patent fee from Optoma. �1080i@25Hz and 720p@50Hz will run in 100Hz; 1080p@24Hz will run in 144Hz. Other 3D timings will �run in 120Hz.

Page 58: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English58

aDDITIonal InfoRmaTIon

Image size and projection distance(1080P)

Diagonal length size of (16e:9)

screen

screen size W x H Projection Distance (D)offset

(m) (inch) (m) (inch)

Width Height Width Height Wide Tele Wide Tele (m) (inch)

36 0.80 0.45 31.38 17.65 1.2 1.3 3.94 4.27 0.07 2.76

40 0.89 0.5 34.86 19.6 1.3 1.4 4.27 4.59 0.08 3.15

50 1.11 0.62 43.58 24.5 1.6 1.8 5.25 5.91 0.10 3.94

60 1.33 0.75 52.29 29.4 2.0 2.2 6.56 7.22 0.12 4.72

70 1.55 0.87 61.01 34.3 2.3 2.5 7.55 8.20 0.14 5.51

80 1.77 1 69.73 39.2 2.6 2.9 8.53 9.51 0.16 6.30

90 1.99 1.12 78.44 44.1 2.9 3.2 9.51 10.50 0.18 7.09

100 2.21 1.25 87.16 49 3.3 3.6 10.83 11.81 0.19 7.48

120 2.66 1.49 104.59 58.8 3.9 4.3 12.80 14.11 0.24 9.45

150 3.32 1.87 130.74 73.5 4.9 5.4 16.08 17.72 0.30 11.81

180 3.98 2.24 156.88 88.2 5.9 6.5 19.36 21.33 0.36 14.17

200 4.43 2.49 174.32 98.1 6.6 7.2 21.65 23.62 0.40 15.75

250 5.53 3.11 217.89 122.6 8.2 9.0 26.90 29.53 0.50 19.69

300 6.64 3.74 261.47 147.1 9.8 10.8 32.15 35.43 0.59 23.23

Zoom ratio is 1.1x.notee:

Width

Heig

ht Diagonal

Top View

Side View

Projection Distance (D)

Projection Distance (D)

Screen

Screen

Screen (W)

Screen (H)

Offset (Hd)

Page 59: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 59

Projector dimensions and ceiling mount installationTo prevent damage to your projector, please use the Optoma ceiling mount.1. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to 2. the projector meet the following specifications: � Screw type: M4*3

Minimum screw length: 10mm �

57.20

82.30

64.00

314.1885.0050.65 55.00

223.4

588

.2210

1.72

Unit: mm

Lens

Please note that damage resulting from incorrect installation will void the warranty.notee:

Warning:

If you buy a ceiling mount from another company, please be sure to use the correct screw size. �Screw size will vary depending on the thickness of the mounting plate.

Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector. �

Avoid installing the projector near a heat source. �

Page 60: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English60

aDDITIonal InfoRmaTIon

IR remote codes

ON OFF

Menu

VGA1

HDMI1

User2

Contrast

Aspect ratio

DB

Volume

Source Re-sync

User1

Brightness

Keystone

Mute

User3

Mode

3D

Sleep Timer

Volume

HDMI2

VGA2 Video YPbPr

KeyCustome code Data

code Printing-key definition Description

byte 1 byte 2 byte 3

Power on 32 CD 02 ON Press to turn on the projector.

Power off 32 CD 2E OFF Press to turn off the projector.

User 1 32 CD 36 User1User defined keys. Please see page 50 to setup.User 2 32 CD 65 User2

User 3 32 CD 66 User3

Brightness 32 CD 41 Brightness Adjust the brightness of the image.

Contrast 32 CD 42 Contrast Control the degree of difference between the lightest and darkest parts of the picture.

Display mode 32 CD 05 Mode Select a display mode for optimized settings for different applications. Please see page 28.

Keystone 32 CD 07 Keystone Adjust image distortion caused by tilting the projector.

Page 61: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 61

aDDITIonal InfoRmaTIon

KeyCustome code Data

code Printing-key definition Description

byte 1 byte 2 byte 3

Aspect ratio 32 CD 64 Aspect ratio Press to change aspect ratio of a displayed image.

3D 32 CD 89 3D Manually select a 3D mode that matches your 3D content.

Mute 32 CD 52 Mute Momentarily turns off / on the audio.

DB (Dynamic Black) 32 CD 44 DB Automatically adjusts the picture brightness

to give optimum contrast performance.

Sleep timer 32 CD 63 Sleep Timer Sets the countdown timer interval.

Volume + 32 CD 09 Volume + Adjust to increase volume.

Four direction keys

32 CD 11 ▲

Use ▲, ◄, ►, or ▼ to select items or makeadjustments to your selection.

32 CD 10 ◄32 CD 12 ►32 CD 14 ▼

Source 32 CD 18 Source Press “Source” to select an input signal.

Enter key 32 CD 0F Confirm your item selection.

Re-sync 32 CD 04 Re-sync Automatically synchronizes the projector to the input source.

Volume - 32 CD 0C Volume - Adjust to decrease volume.

Menu 32 CD 0E MenuDisplay or exit the on-screen display menusfor projector.

HDMI 1 32 CD 16 HDMI1Press “HDMI1” to choose source fromHDMI 1 / MHL connector.

HDMI 2 32 CD 30 HDMI2Press “HDMI2” to choose source fromHDMI 2 connector.

VGA 1 32 CD 1B VGA1 No function

VGA 2 32 CD 1E VGA2 No function

Video 32 CD 1C Video No function

YPbPr 32 CD 17 YPbPr No function

Page 62: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English62

aDDITIonal InfoRmaTIon

Using the Help buttonThe Help function ensures easy setup and operation. Press the “?” button on the keypad to open the Help menu.

Help � button functions only when no input source is detected.

HELP

No image appears on-screen

Exit

Page 63: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 63

HELP

Exit

Ensure all the cables and power connections are correctly and securely

No image appears on-screen

connected as described in the Installation section of User's Manual.

Ensure all the pins of connectors are not bent or broken.

Ensure that the [AV MUTE] feature is not turned on.

[Next]

Exit

[Prev]

No image appears on-screen

HELP

If you are using a Notebook :

1. First, follow

2. Press the toggle output settings. Example : [Fn]+[F4]

System Preference -> Display -> Arrangement -> Mirror display

Mac Apple:

the steps above to adjust resolution of the computer.

HELP

Exit

Image has slanted sides

Image is too small or too large

There is no audio heard or the volume is too low

Page 64: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English64

HELP

Exit

If possible, reposition the projector so that is centered on the screen and

Image has slanted sides

below the bottom of the screen.

Press [LEYSTONE + / -] button until the sides are vertical on theremote control.

[KEYSTONE + / -]

HELP

Exit

[DISPLAY | Format]

Image is too small or too large

Adjust the Zoom Ring on the top of projector.

Move the projector closer to or further from the screen.

Press [MENU] button on the remote control or projector panel, go to

DISPLAY | Format and try the different settings.

HELP

Exit

[Volume]

There is no audio heard or the volume is too low

Is the volume setting at the minimum?

Is the cable connected properly to the projector?

Turn up the volume setting.

Check the physical connection and ensure the cable is connected

properly from the source to projector.

Page 65: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 65

aDDITIonal InfoRmaTIon

TroubleshootingIf you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center.

Image problems

No image appears on-screen

Ensure all the cables and power connections are correctly and securely connected as described in the �"Installation" section.

Ensure the pins of connectors are not crooked or broken. �

Check if the projection lamp has been securely installed. Please refer to the "Replacing the Lamp" �section.

Ensure that the "Mute" feature is not turned on. �

Image is out of focus

Adjust the Focus Ring on the projector lens. �

Make sure the projection screen is between the required distance from the projector. (Please refer to �page 58).

The image is stretched when displaying 16:9 DVD title

When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format �on projector side.

If you play the LBX format DVD title, please change the format as LBX in projector OSD. �

If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. �

Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player. �

Image is too small or too large

Adjust the zoom lever on the top of the projector. �

Move the projector closer to or further from the screen. �

Press "Menu" on the projector panel, go to "Display-->Format". Try the different settings. �

Image has slanted sides:

If possible, reposition the projector so that it is centered on the screen and below the bottom of the �screen.

Use "Display-->V Keystone" or “Display-->H Keystone” from the OSD to make an adjustment. �

Image is reversed

Select "Setup-->Projection" from the OSD and adjust the projection direction. �

Blurry double image

Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image. �

Page 66: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English66

aDDITIonal InfoRmaTIon

Two images, side-by-side format

Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side. �

Image does not display in 3D

Check if the battery of 3D glasses is drained. �

Check if the 3D glasses is turned on. �

When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS". �

other problems

The projector stops responding to all controls

If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before �reconnecting power.

Lamp burns out or makes a popping sound

When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this �happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 54-55.

Remote control problems

If the remote control does not work

Check the operating angle of the remote control is pointed within ±15° both horizontally and vertically �to the IR receivers on the projector.

Make sure there are not any obstructions between the remote control and the projector. Move to within �6m (20 ft) of the projector.

Make sure batteries are inserted correctly. �

Replace batteries if they are exhausted. �

Page 67: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 67

aDDITIonal InfoRmaTIon

Warning indicatorsWhen the warning indicators (see below) light up or flash, the projector will automatically shutdown:

"LAMP" LED indicator is lit red and if "On/Standby" indicator flashes amber. �

"TEMP" LED indicator is lit red and if "On/Standby" indicator flashes amber. This indicates the �projector has overheated. Under normal conditions, the project can be switched back on.

"TEMP" LED indicator flashes red and if "On/Standby" indicator flashes amber. �Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or flash, please contact your nearest service center for assistance.

lED lightning messages

Message Power LED Power LED Temp-LED Lamp-LED

(Red) (Green or Blue) (Red) (Red)

Standby state (Input power cord)

Steady light

Power on (Warming)Flashing(0.5 sec off / 0.5 sec on)

Power on and Lamp lighting Steady light

Power off (Cooling)

Flashing (0.5 sec off /0.5 sec light). Back to red steady light when cooling fan turns off.

Quick Resume (100 secs)

Flashing(0.25 sec off / 0.25 sec light)

Error (Over temp.) Flashing

Error (Fan failure) Flashing Flashing

Error (Lamp failure) Flashing

Power off: �

Power Off?

Press Power key again

Lamp warning: �

Lamp Warning

Lamp life exceeded.

Page 68: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English68

aDDITIonal InfoRmaTIon

Temperature warning: �

Please:

1. Make sure air in and outlets are not blocked.2. Make sure the environment temperature is under 45 degree C.

If the problem persists in spite of the above.Please contact a service center for repair.

Warning! TEMPERATURE TOO HIGH

Fan failed: �

Warning! FAN LOCKED

The projector will switch off automatically..

Please contact a service center for repair.

Out of display range: �

Out of Range

Calibration failed: �

Calibration Fail !

Power down warning: �

Power Down Timer Active

Power down in 60 sec

Security timer alarm: �

Security Timer Alarm

Time out in 60 sec

Page 69: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 69

aDDITIonal InfoRmaTIon

Specifications

optical Description

Maximum resolution- Video timing maximum up to :1080p

- Graphic up to WUXGA@60HzLens - Manual zoom and manual focus

Lamp- ECO Mode < = 0.5 W @ 110/220VAC

- Active Mode >0.5W @ 110/220VACImage size (diagonal) 41.8”~305”Projection distance 1.5m~10m

Electrical Description

Inputs- HDMI1

- HDMI2 + MHL (2.2)

Outputs

- Audio 3.5mm

- USB-A Power (0.9A)

- 12V Trigger

Service port- 3D Sync VESA

- USB Mouse / ServiceColor reproduction 1073.4 Million color

Scan rate- Horizontal scan rate: 15.375~91.146 KHz

- Vertical scan rate: 24~ 85 Hz (120Hz for 3D featured projector)Built-in speaker Yes, 10WPower requirement 100 - 240V AC 50/60HzInput current 2.5-1.0 A

mechanical DescriptionInstallation orientation Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/RearDimensions 314.3 mm (W) x 223.6 mm (D) x 100.35 mm (H)Weight <2.7 kg

Environmental conditions - Operating: 5°C ~ 40°C, humidity 10% ~ 85%, non-condensing- Non-operating: -10°C ~ 60°C, humidity 5% ~ 95%, non-condensing

All specifications are subject to change without notice.notee:

Page 70: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English70

aDDITIonal InfoRmaTIon

Optoma global officesFor service or support, please contact your local office.

Usa3178 Laurelview Ct. 888-289-6786Fremont, CA 94538, USA 510-897-8601www.optomausa.com [email protected]

Canada3178 Laurelview Ct. 888-289-6786Fremont, CA 94538, USA 510-897-8601www.optomausa.com [email protected]

latin america3178 Laurelview Ct. 888-289-6786Fremont, CA 94538, USA 510-897-8601www.optomausa.com [email protected]

Europe42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK +44 (0) 1923 691 800www.optoma.eu +44 (0) 1923 691 888Service Tel : +44 (0)1923 691865 [email protected]

benelux bVRandstad 22-123 +31 (0) 36 820 02521316 BW Almere +31 (0) 36 548 9052The Netherlands www.optoma.nl

france Bâtiment E +33 1 41 46 12 20 81-83 avenue Edouard Vaillant +33 1 41 46 94 3592100 Boulogne Billancourt, France [email protected]

spain C/ José Hierro,36 Of. 1C +34 91 499 06 06 28522 Rivas VaciaMadrid, +34 91 670 08 32Spain

DeutschlandWiesenstrasse 21 W +49 (0) 211 506 6670D40549 Düsseldorf, +49 (0) 211 506 66799Germany [email protected]

scandinaviaLerpeveien 25 +47 32 98 89 903040 Drammen +47 32 98 89 99 Norway [email protected]

PO.BOX 9515 3038 DrammenNorway

KoreaWOOMI TECH.CO.,LTD. +82+2+34430004 4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005Seoul,135-815, KOREA korea.optoma.com

Japan東京都足立区綾瀬3-25-18株式会社オーエス [email protected]コンタクトセンター:0120-380-495 www.os-worldwide.com

Taiwan12F., No.213, Sec. 3, Beixin Rd., +886-2-8911-8600Xindian Dist., New Taipei City 231, +886-2-8911-6550Taiwan, R.O.C. [email protected] asia.optoma.com

Hong KongUnit A, 27/F Dragon Centre,79 Wing Hong Street, +852-2396-8968Cheung Sha Wan, +852-2370-1222Kowloon, Hong Kong www.optoma.com.hk

China5F, No. 1205, Kaixuan Rd., +86-21-62947376Changning District +86-21-62947375Shanghai, 200052, China www.optoma.com.cn

Page 71: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English 71

aDDITIonal InfoRmaTIon

DaRbEEVIsIon, InC.lICEnsE aGREEmEnT

noTICE - REaD THIs bEfoRE UsInG THE DEVICE

USING THE DEVICE ACCOMPANYING THIS LICENSE INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. READ ALL OF THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT PRIOR TO INSTALLING OR USING THE DEVICE. IF YOU DO NOT ACCEPT THESE TERMS, YOU MUST RETURN THE DEVICE TO THE SELLER AND REFRAIN FROM USING IT.

THE DEVICE THAT YOU PURCHASED INCLUDES PROPRIETARY FIRMWARE (HEREINAFTER, THE “PROGRAM”) INCORPORATED INTO INTEGRATED CIRCUITS. YOU MAY NOT COPY, MODIFY, REVERSE ENGINEER, CLONE OR TRANSFER THE PROGRAM OR THE PRODUCT’S DOCUMENTATION EXCEPT AS EXPRESSLY PROVIDED IN THIS AGREEMENT.

license1. . This Program and the accompanying Documentation are licensed, not sold, to you by Darbeevision, Inc. (“Licensor”). The term “Program” shall also include any updates of the Program licensed to you by Licensor. Subject to the terms of this agreement, you have a non-exclusive and nontransferable right to use the Program and Documentation for non-commercial (e.g., not for resale or rental or the like), educational, evaluation or personal purposes only. You may use the Program only as incorporated into the integrated circuit that is part of the particular unit of the device that contains it. You agree to use your best efforts to prevent and protect the contents of the Program and Documentation from unauthorized disclosure or use. Licensor and its licensors reserve all rights not expressly granted to you. Licensor’s licensees are the intended third party beneficiaries of this agreement and have the express right to rely upon and directly enforce the terms set forth herein.

limitation on Use2. : You may not rent, lease, sell or otherwise transfer or distribute copies of the Program or Documentation to others. You may not modify or translate the Program or the Documentation without the prior written consent of Licensor. You may not reverse assemble, reverse compile or otherwise attempt to create the source code from the Program. You may not use Licensor’s name or other trademarks or refer to Licensor or Licensor’s products directly or indirectly in any papers, articles, advertisements, sales presentations, news releases or releases to any third party without the prior written approval of Licensor for each such use. You may not release the results of any performance or functional evaluation of any Program to any third party without prior written approval of Licensor for each such release. This product provides the ability to turn off DARBEE Visual Presence (DVP™) processing, because the DVP technology processing feature in this product is not intended for commercial broadcast or theatrical presentation applications. By using this product, you accept that the DVP technology ingredient is intended for personal or small network use and should be switched off if this video processor system is used to process video for commercial broadcast or commercial theatrical viewing applications. An additional commercial license is available from DarbeeVision, Inc. for larger video network, distribution, commercial applications.

Copyright3. : The Program and related Documentation are copyrighted by Licensor. You may not copy the Program (or this license). You may make one copy of the Documentation and print one copy of any on-line documentation or other materials provided to you in electronic form. Any and all other copies of the Program and any copy of the Documentation made by you are in violation of this license.

ownership4. : You agree that the Program and Documentation belong to Licensor. You agree that you neither own nor hereby acquire any claim or right of ownership to the Program and Documentation or to any related patents, copyrights, trademarks or other intellectual property. Licensor retains all right, title and interest in and to the Documentation and all copies and the Program at all times, regardless of the form or media in or on which the original or other copies may subsequently exist. This license is not a sale of the original or any subsequent copy.

Term and Termination5. . This license is effective until terminated.

Page 72: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

English72

aDDITIonal InfoRmaTIon

DIsClaImER of WaRRanTY6. . LICENSOR PROVIDES THE PROGRAM, THE PROPRIETARY IC AND THE DOCUMENTATION “AS IS” WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. All risk of quality and performance of the Program, the device into which it is incorporated and the Documentation is with the Licensee. Should any of the foregoing prove defective, you and not Licensor assume the entire cost of any service and repair. This disclaimer of warranty constitutes an essential part of this agreement.

lImITaTIon of REmEDIEs7. . IN NO EVENT WILL BE LIABLE FOR ANY INDIRECT DAMAGES OR OTHER RELIEF ARISING OUT OF YOUR USE OR INABILITY TO USE THE PROGRAM, THE DEVICE INTO WHICH IT IS INCORPORATED OR THE DOCUMENTATION, INCLUDING, BY WAY OF ILLUSTRATION AND NOT LIMITATION, LOST PROFITS, LOST BUSINESS OR LOST OPTOMARTUNITY, OR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL OR EXEMPLARY DAMAGES, INCLUDING LEGAL FEES, ARISING OUT OF SUCH USE OR INABILITY TO USE THE PROGRAM, EVEN IF LICENSOR OR AN AUTHORIZED LICENSOR DEALER, DISTRIBUTOR OR SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.

applicable law; Dispute Resolution8. . This license will be governed by the laws of the State of California, without reference to conflicts of laws principles. The United Nations Convention on Contracts for the Sale of Goods does not apply to this license. All disputes hereunder shall be settled in the state or federal courts located in Orange County, California.

Export Controls9. . The Program and the underlying information and technology may not be downloaded or otherwise exported or reexported (i) into (or to a national or resident of) Cuba, North Korea, Iran, Syria, Sudan or any other country to which the U.S. has embargoed goods; or (ii) to anyone on the U.S. Treasury Department’s list of Specially Designated Nationals or the U.S. Commerce Department’s Table of Deny Orders. By downloading or using the Program, you are agreeing to the foregoing and you represent and warrant that you are not located in, under the control of, or a national or resident of any such country or on any such list.

U.s. Government End Users10. . Every sale, license, or other distribution of any Licensee Product to a customer which is a department, division, or agency of the United States Government shall contain the following provision, or a substantially equivalent provision: U.S. GOVERNMENT RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure of this software by the Government is subject to the conditions set forth in FAR 12.212 and DFARS 227.720 and/or in similar or successor clauses in the FAR or Supplements to it. Any and all use, duplication, transfers for any reason is restricted in accordance with the terms and conditions of the Licensor’s standard commercial license agreement which is incorporated herein as though fully set forth. All other use, for any reason, is prohibited. Unpublished rights are reserved under the Copyright Laws of the United States.

no other agreements11. . This Agreement constitutes the entire agreement between the Parties with respect to the Program and the Documentation, and supersedes any other written or oral agreement.

Page 73: DLP Projector - B&H Photo Video. Logo Options. HDMI Link Settings

www.optoma.com