dirección/address: maría de luna, 3 - edificio torres ... · código validación electrónica:...
TRANSCRIPT
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 1 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
ANEXO TÉCNICO ACREDITACIÓN Nº 581/LE1265
SCHEDULE OF ACCREDITATION
Entidad/Laboratory: LABORATORIO DE METROLOGÍA ELÉCTRICA, CIRCE-Universidad de Zaragoza
Dirección/Address: María de Luna, 3 - Edificio Torres Quevedo; 50018 Zaragoza
Norma de referencia/Standars: UNE-EN ISO/IEC 17025: 2005 (CGA-ENAC-LEC)
Ensayos en la siguiente área/Test in the following area:
Ensayos de energías renovables (Renewable energy tests)
Categoría 0 (Ensayos en el laboratorio permanente) Category 0 (Test in the permanent laboratory)
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Aerogeneradores y FACTS
Wind turbines and FACTS
Ensayo de validación de modelo para simulación de componentes, conforme a las condiciones establecidas en el Apdo. 7 del documento “Procedimientos de Verificación, Validación y Certificación de los requisitos del PO 12.3 sobre la respuesta de las instalaciones eólicas y fotovoltaicas ante huecos de tensión”, (PVVC). Versión 10 de 26 de enero de 2012 de la Asociación Empresarial Eólica (AEE)
Model validation according to section 7 of document, “Procedure for verification, validation and certification of the requirements of the P.O. 12.3 on the response of wind farms and photovoltaic plants in the event of voltage dips” (PVVC). Version 10, 26
th January 2012, published by Spanish Wind
Energy Association (AEE)
Procedimiento interno
Internal procedure
PE027
Aerogeneradores
Wind turbines
Ensayo de validación de modelo para simulación de componentes conforme a las condiciones establecidas en el documento Technical Guidelines for Power Generating Units. Part 4: “Demands on Modelling and Validating Simulation Models of the Electrical Characteristics of Power Generating Units and Systems”, Rev. 5, 22.03.2010. Published by FGW e.V
Model validation according to Technical Guidelines for Power Generating Units. Part 4: “Demands on Modelling and Validating Simulation Models of the Electrical Characteristics of Power Generating Units and Systems”, Revision 5, 22.03.2010. Published by FGW e.V
Procedimiento interno PE028 para la aplicación del documento FGW-TG Part 4, Rev. 5, 22.03.2010
Internal procedure PE028 to apply FGW-TG Part 4, Revision 5, 22.03.2010
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 2 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Solar Fotovoltaica (Photovoltaic energy)
Inversores solares (Monofásicos y trifásicos) y Sistemas Compensadores de Huecos (FACTS)
Photovoltaic inverters (single-phase and three-phase) and Flexible AC Transmission Systems (FACTS)
Ensayo de validación de modelo para simulación de componentes, conforme a las condiciones establecidas en el Anexo III “Instalaciones fotovoltaicas” del documento “Procedimientos de Verificación, Validación y Certificación de los requisitos del PO 12.3 sobre la respuesta de las instalaciones eólicas y fotovoltaicas ante huecos de tensión”, PVVC, Versión 10 de 26 de enero de 2012 de la Asociación Empresarial Eólica (AEE)
Model validation test according to Annex III of the document “Procedure for verification,n validation and certification of the requirements of the P.O. 12.3 on the response of wind farms and photovoltaic plants in the event of voltage dips” (PVVC) Version 10, 26
th January 2012, published by Spanish
Wind Energy Association (AEE)
Procedimiento interno
Internal procedure
PE027
Inversores solares (Monofásicos y trifásicos) y Sistemas Compensadores de Huecos (FACTS)
Photovoltaic inverters (single-phase and three-phase) and Flexible AC Transmission Systems (FACTS)
Ensayo de validación de modelo para simulación de componentes, conforme a las condiciones establecidas en el documento Technical Guidelines for Power Generating Units. Part 4: “Demands on Modelling and Validating Simulation Models of the Electrical Characteristics of Power Generating Units and Systems”, Revision 5, 22.03.2010. Published by FGW e.V
Model validation test according to the document Technical Guidelines for Power Generating Units. Part 4: “Demands on Modelling and Validating Simulation Models of the Electrical Characteristics of Power Generating Units and Systems”, Revision 5, 22.03.2010. Published by FGW e.V
Procedimiento interno PE028 para la aplicación del documento FGW-TG Part 4, Revision 5, 22.03.2010
Internal procedure PE028 to apply FGW-TG Part 4, Revision 5, 22.03.2010
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 3 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
Categoría I (Ensayos “in situ”) Category I (“on site” Tests)
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Aerogeneradores
Wind turbines
Curva de potencia
Power performance
UNE-EN 61400-12-1:2007 IEC 61400-12-1:2005 MEASNET Power Performance Measurement Procedure, Versión 5 Diciembre 2009
UNE‐EN 61400‐12‐1:2007 IEC 61400‐12‐1:2005 MEASNET Power Performance Measurement Procedure, Version 5 December 2009
Curva de potencia con anemometría de góndola
Power performance based on nacelle anemometry
IEC 61400-12-2:2013
IEC 61400‐12‐2:2013
Medida de ruido acústico
Measurement of acoustic noise
UNE-EN 61400-11:2013
IEC 61400-11:2012 Ed3
MEASNET: Acoustic Noise
Measurement Procedure, Versión 3, November 2011
RenewableUK Small Wind Turbine Standard 15/01/2014, Section 2: Acoustic Noise Measurement
AWEA Small Wind Turbine Performance and Safety Standard. AWEA 9.1 2009 Section 3: Acoustic Sound Testing
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 4 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Pequeños aerogeneradores
Small wind turbines
Duración
Duration
UNE-EN 61400-2:2007 Apartado 9.4
IEC 61400-2:2013 Ed3. Section 13.4. Duration Testing
RenewableUK Small Wind Turbine Standard, 15/01/2014. Section 4: Compliance with IEC 61400-2 Small Wind Turbines (Section 13.4. Duration Testing)
AWEA Small Wind Turbine Performance and Safety Standard. AWEA 9.1 2009 Section 5: Duration Test
Aerogeneradores y FACTS
Wind turbines and FACTS
Medida y evaluación de huecos de tensión y de la respuesta eléctrica de aerogeneradores y FACTS frente a los mismos, conforme a las condiciones establecidas en el Apdo. 6 del documento “Procedimientos de Verificación, Validación y Certificación de los requisitos del PO 12.3 sobre la respuesta de las instalaciones eólicas y fotovoltaicas ante huecos de tensión”, PVVC, Versión 10 de 26 de enero de 2012 de la Asociación Empresarial Eólica (AEE)
Measurement and assessment of response of wind turbines and FACTS in the event of voltage dips according to “Procedure for verification, validation and certification of the requirements of the P.O. 12.3 on the response of wind farms and photovoltaic plants in the event of voltage dips” (PVVC) Version 10, 26th January 2012, published by Spanish Wind Energy Association (AEE).
Procedimiento interno
Internal procedure
PE026
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 5 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Aerogeneradores
Wind turbines
Medida y evaluación de parámetros eléctricos en instalaciones conectadas a la red transporte y equipo generador. Comprende los siguientes ensayos y/o medidas:
Medida y evaluación de huecos de tensión Medida y evaluación de flicker Medida y evaluación de armónicos Medida y evaluación de la respuesta ante
perturbaciones de frecuencia Evaluación de la potencia intercambiada Medida y evaluación de desequilibrios de tensión Medida y evaluación de sobretensiones Medida y evaluación de desfases Evaluación del control de tensión
Measurement and assessment of electrical parameters of
grid connected wind turbines and generator sets. Includes
the following tests and/or measures:
Measurement and assessment of voltage dips
Measurement and assessment of flicker
Measurement and assessment of harmonics
Measurement and assessment of the response in the
event of frequency perturbance
Assessment of exchanged power
Measurement and assessment of voltage inbalances
Measurement and assessment of overvoltages
Measurement and assessment of phase shifts
Assessment of voltage control
Procedimientos internos
Internal procedures
PE029 PE055 PE021 PE095 PE075 PE115 PE020 PE045 PE065 PE125
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 6 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Aerogeneradores
Wind turbines
Medida y evaluación de parámetros eléctricos, conforme a las condiciones establecidas en el documento Technical Guidelines for Power Generating Units. Part 3: “Determination of electrical characteristics of power generating units connected to MV, HV and EHV grids”, Revision 21, 22.03.2010. Published by FGW e.V
Comprende los siguientes ensayos y/o medidas:
Medida y evaluación de huecos de tensión
Medida y evaluación de flicker
Medida y evaluación de armónicos
Medida y evaluación de la respuesta ante perturbaciones de frecuencia
Evaluación de la provisión de potencia activa
Evaluación de la provisión de potencia reactiva
Medida y evaluación de las operaciones de conexión y desconexión
Evaluación de la desconexión de la PGU de la red
Verificación de las condiciones de arranque
Measurement and assessment of electrical parameters according to the Technical Guidelines for Power Generating Units. Part 3: “Determination of electrical characteristics of power generating units connected to MV, HV and EHV grids”, Revision 22, 01.07.2011. Published by FGW e.V
Includes the following tests and measures:
Measurement and assessment of voltage dips
Measurement and assessment of flicker
Measurement and assessment of harmonics
Measurement and assessment of the response in the
event of frequency perturbance
Assessment of active power provision
Assessment of reactive power provision
Measurement and assessment of switching operations
Assessment of disconnection of the PGU from the grid
Verification of cut-in conditions
Procedimientos internos para la aplicación del documento FGW-TG Part 3, Revision 21, 22.03.2010
Internal procedures to apply the document FGW-TG Part 3, Revision 22, 01.07.2011
PE030
PE056
PE106
PE096
PE076
PE116
PE126
PE136 PE146
PE156
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 7 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Eólica (Wind energy)
Redes de distribución eléctrica en baja tensión y aerogeneradores en el lado de baja tensión
Low voltage distribution power networks and wind turbines at low voltage side
Parámetros básicos de la calidad de red:
Frecuencia
Amplitud de la tensión
Severidad de flicker
Huecos de tensión
Sobretensiones temporales
Interrupciones de la tensión de suministro
Armónicos de tensión y corriente hasta orden 50
Interarmónicos de tensión y corriente hasta orden 50
Basic power quality parameters: • Frequency • Voltage Amplitude • Flicker severity • Voltage dips • Voltage swells • Interruptions of voltage supply • Voltage and current harmonics up to order 50th • Voltage and current interharmonics up to order 50th
UNE-EN 50160:2011 UNE-EN 61000-4-30:2009
Parámetros eólicos
Wind parameters
Toma de datos eólicos para evaluación del potencial eólico
Wind data gathering for wind resource assessment
UNE 500520:2002 Orden 6 de julio de 2004 Diputación Gral. Aragón
UNE 500520:2002 Order of 6th of July of 2004 Government of Aragon
Solar Fotovoltaica (Photovoltaic energy)
Inversores solares (Monofásicos y trifásicos) y Sistemas Compensadores de Huecos (FACTS)
Photovoltaic inverters (single-phase and three-phase) and Flexible AC Transmission Systems (FACTS)
Umáx = 32,4 kV Imáx = 3 kA fmuestreo = 51,2 kHz
Medida y evaluación de la respuesta de los Sistemas de Conversión Fotovoltaica (SCFV) ante huecos de tensión conforme a las condiciones establecidas en el Apdo. 5 del Anexo III del documento “Procedimientos de Verificación, Validación y Certificación de los requisitos del PO 12.3 sobre la respuesta de las instalaciones eólicas y fotovoltaicas ante huecos de tensión”, PVVC, Versión 10 de 26 de enero de 2012 de la Asociación Empresarial Eólica (AEE)
Measurement and assessment of response of Photovoltaic convertion systems in the event of voltage dips accordind to Section 5 of Annex III of “Procedure for verification, validation and certification of the requirements of the P.O. 12.3 on the response of wind farms and photovoltaic plants in the event of voltage dips” (PVVC) Version 10, 26
th January
2012, published by Spanish Wind Energy Association (AEE).
Procedimiento interno Internal procedure
PE026
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 8 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Solar Fotovoltaica (Photovoltaic energy)
Inversores solares (Monofásicos y trifásicos) y Sistemas Compensadores de Huecos (FACTS)
Photovoltaic inverters (single-phase and three-phase) and Flexible AC Transmission Systems (FACTS)
Medida y evaluación de parámetros eléctricos en instalaciones conectadas a la red transporte y equipo generador. Comprende los siguientes ensayos y/o medidas:
Medida y evaluación de huecos de tensión Medida y evaluación de flicker Medida y evaluación de armónicos Medida y evaluación de la respuesta ante
perturbaciones de frecuencia Evaluación de la potencia intercambiada Medida y evaluación de desequilibrios de tensión Medida y evaluación de sobretensiones Medida y evaluación de desfases Evaluación del control de tensión
Measurement and assessment of electrical parameters of
grid connected units. Includes the following tests and/or
measures:
Measurement and assessment of voltage dips
Measurement and assessment of flicker
Measurement and assessment of harmonics
Measurement and assessment of the response in the
event of frequency perturbances
Assessment of exchanged power
Measurement and assessment of voltage inbalances
Measurement and assessment of overvoltages
Measurement and assessment of phase shifts
Assessment of voltage control
Procedimientos internos Internal procedures
PE029
PE055
PE021
PE095
PE075 PE115
PE020
PE045
PE065
PE125
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí
Acreditación/Accreditation nº 581/LE1265 Anexo Técnico Rev. /Technical Annex Ed. 11
Fecha/Date 06/11/14 Hoja/Page 9 de 9
The present technical annex is subject to possible modifications. The validity status of the accreditation can be confirmed in www.enac.es
PRODUCTO/MATERIAL A ENSAYAR
PRODUCTS/MATERIALS TESTED
ENSAYO TYPE OF TEST
NORMA/PROCEDIMIENTO DE ENSAYO
STANDARD SPECIFICATIONS/ TEST PROCEDURE
Solar Fotovoltaica (Photovoltaic energy)
Inversores solares (Monofásicos y trifásicos) y Sistemas Compensadores de Huecos (FACTS)
Photovoltaic inverters (single-phase and three-phase) and Flexible AC Transmission Systems (FACTS)
Medida y evaluación de parámetros eléctricos, conforme a las condiciones establecidas en el documento Technical Guidelines for Power Generating Units. Part 3: “Determination of electrical characteristics of power generating units connected to MV, HV and EHV grids”, Revision 21, 22.03.2010. Published by FGW e.V
Comprende los siguientes ensayos y/o medidas:
Medida y evaluación de huecos de tensión Medida y evaluación de flicker Medida y evaluación de armónicos Medida y evaluación de la respuesta ante
perturbaciones de frecuencia Evaluación de la provisión de potencia activa Evaluación de la provisión de potencia reactiva Medida y evaluación de las operaciones de
conexión y desconexión Evaluación de la desconexión de la PGU de la red Verificación de las condiciones de arranque
Measurement and assessment of electrical parameters according to the Technical Guidelines for Power Generating Units. Part 3: “Determination of electrical characteristics of power generating units connected to MV, HV and EHV grids”, Revision 22, 01.07.2011. Published by FGW e.V
Includes the following tests and/or measures:
Measurement and assessment of voltage dips
Measurement and assessment of flicker
Measurement and assessment of harmonics
Measurement and assessment of the response in the
event of frequency perturbances
Assessment of active power provision
Assessment of reactive power provision
Measurement and assessment of switching operations
Assessment of disconnection of the PGU from the grid
Verification of cut-in conditions
Procedimientos internos para la aplicación del documento FGW-TG Part 3, Revision 21, 22.03.2010
Internal procedures to apply the document FGW-TG Part 3, Revision 22, 01.07.2011
PE030
PE056
PE106
PE096
PE076
PE116
PE126
PE136
PE146
PE156
Código Validación Electrónica: 6k1wR1Ne3KlH98t01U
El presente anexo técnico está sujeto a posibles modificaciones. La vigencia de la acreditación y del presente anexo técnico puede confirmarse en
http://www.enac.es/web/enac/validacion-electronica o haciendo clic aquí