dio-24 dio-96/144 user manual nov. 2011 version 2 · dio-24 24-bit compatible dio opto-22 board....

DIO-24

DIO-96/144

User Manual Version 2.4 Nov. 2011

Warranty All products manufactured by ICP DAS are warranted against defective materials for a period of one year from the date of delivery to the original purchaser.

Warning ICP DAS assumes no liability for damages consequent to the use of this product. ICP DAS reserves the right to change this manual at any time without notice. The information furnished by ICP DAS is believed to be accurate and reliable. However, no responsibility is assumed by ICP DAS for its use, nor for any infringements of patents or other rights of third parties resulting from its use.

Copyright Copyright © 2011 by ICP DAS. All rights are reserved.

Trademark Names are used for identification only and may be registered trademarks of their respective companies.

DIO-D24/DIO-96/DIO-144 User Manual (Ver.2.4, Nov. 2011, IMH-007-24) 1

Tables of Contents

DIO-24 24-BIT COMPATIBLE DIO OPTO-22 BOARD.......................................................4

1. INTRODUCTION ..............................................................................................................4

1.1 FEATURES......................................................................................................................4 1.2 APPLICATIONS...............................................................................................................4 1.3 SPECIFICATIONS ............................................................................................................5 1.4 PRODUCT CHECK LIST ..................................................................................................6

2. HARDWARE CONFIGURATION ..................................................................................7

2.1 BOARD LAYOUT ............................................................................................................7 2.2 JUMPER SETTING ...........................................................................................................8

2.2.1 Interrupt Jumper Setting.............................................................................................8 2.2.2 Interrupt Status Setting ...............................................................................................8 2.2.3 Interrupt Trigger Edge Setting ...................................................................................8

2.3 BASE ADDRESS SETTING ...............................................................................................9 2.4 PIN ASSIGNMENTS.......................................................................................................13

3. PROGRAMMING...........................................................................................................15

3.1 REGISTER ....................................................................................................................15 3.2 INTERRUPT HANDLING................................................................................................17 3.3 OUTPUT LATCH...........................................................................................................17 3.4 PROGRAM EXAMPLE ...................................................................................................18

4. SOFTWARE/HARDWARE INSTALLATION.............................................................19

4.1 SOFTWARE INSTALLING PROCEDURE.........................................................................19 4.2 HARDWARE INSTALLING PROCEDURE ........................................................................20

DIO-96/DIO-144 96/144-BIT OPTO-22 COMPATIBLE DIO BOARD........................23

5. SOFTWARE INSTALLATION.......................................................................................23

5.1 FEATURES....................................................................................................................23 5.2 APPLICATIONS.............................................................................................................23 5.3 SPECIFICATIONS ..........................................................................................................24 5.4 PRODUCT CHECK LIST ................................................................................................25

6. HARDWARE CONFIGURATION .....................................................................................26

6.1 BOARD LAYOUT ..........................................................................................................26 6.2 JUMPER SETTING .........................................................................................................27


6.2.1 Interrupt Jumper Setting...........................................................................................27 6.2.2 Interrupt Status Setting .............................................................................................27 6.2.3 96-bit/144-bit Jumper Setting ...................................................................................27

6.3 BASE ADDRESS SETTING.............................................................................................28 6.3.1 96-bit Mode............................................................................................................28 6.3.2 144-bit Mode...........................................................................................................30

6.4 PIN ASSIGNMENTS.......................................................................................................32

7. PROGRAMMING...........................................................................................................34

7.1 REGISTER ....................................................................................................................34 7.2 DATA FORMAT ............................................................................................................36 7.3 INTERRUPT HANDLING................................................................................................38 7.4 OUTPUT LATCH ...........................................................................................................38 7.5 PROGRAM EXAMPLE ...................................................................................................39

8. SOFTWARE/HARDWARE INSTALLATION.............................................................40

8.1 SOFTWARE INSTALLING PROCEDURE ..........................................................................40 8.2 HARDWARE INSTALLING PROCEDURE.........................................................................41

APPENDIX: DAUGHTER BOARD.........................................................................................44

A1. DAUGHTER BOARD COMPARISON TABLE...................................................................44 A2. DB-24P/24PD ISOLATED INPUT BOARD.....................................................................45 A3. DB-24R/24RD RELAY BOARD....................................................................................46 A4. DB-24PR/24PRD........................................................................................................47


DIO-24 24-bit Compatible DIO OPTO-22 Board 24-bit Compatible DIO OPTO-22 Board

1. Introduction 1. Introduction The DIO-24 provides 24 TTL digital I/O lines. The DIO-24 emulates 8255 mode 0 and has an increased output current of 15 mA (source) and 64 mA (sink) , allowing it to control LED, relay, etc. The DIO-24 consists of three 8 bit bi-directional ports and 2 input lines for interrupt enable and interrupt. The 8 bit ports are named port A(PA),port B(PB) and port C(PC). The port C can be split into two four bit. All ports are configured as inputs upon power-up or reset. The DIO-24 uses 4 consecutive I/O locations in I/O addressing space. The base address is selectable from 200 to 3FF hex. The interrupt signal can be connected to any of the interrupt levels 2 through 7.

The DIO-24 provides 24 TTL digital I/O lines. The DIO-24 emulates 8255 mode 0 and has an increased output current of 15 mA (source) and 64 mA (sink) , allowing it to control LED, relay, etc. The DIO-24 consists of three 8 bit bi-directional ports and 2 input lines for interrupt enable and interrupt. The 8 bit ports are named port A(PA),port B(PB) and port C(PC). The port C can be split into two four bit. All ports are configured as inputs upon power-up or reset. The DIO-24 uses 4 consecutive I/O locations in I/O addressing space. The base address is selectable from 200 to 3FF hex. The interrupt signal can be connected to any of the interrupt levels 2 through 7.

1.1 Features 1.1 Features

24 digital I/O lines Emulate 8255 mode (Basic input/output mode) Buffer output for higher driving capability than 8255 Register compatible to 724 series Programmable interrupt handling Output status readback

1.2 Applications

Interfacing with any OPTO-22 compatible I/O module Digital I/O control Contact closure monitoring and alarm monitoring Useful with parallel interface devices


1.3 Specifications Model Name DIO-24 Digital Input Channels 24 (OPTO-22 compatible) Compatibility 5 V/TTL Input Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min. Response Speed 1.0 MHz (Typical) Digital Output Channels 24 (OPTO-22 compatible) Compatibility 5 V/TTL Output Voltage Logic 0: 0.4 V max.

Logic 1: 2.4 V min. Output Capability Sink: 0.8 mA @ 0.8 V

Source: -2.4 mA @ 2.0 V Response Speed 1.0 MHz (Typical) General Bus Type ISA I/O Connector 20-pin box header x 2

50-pin box header x 1 Dimensions (L x W x D) 182 mm x 110 mm x 22 mm Power Consumption 900 mA @ +5 V (typical) Operating Temperature 0 ~ 60 °C Storage Temperature -20 ~ 70 °C Humidity 5 ~ 85% RH, non-condensing


1.4 Product Check List The shipping package includes the following items:

One DIO-24 card One software utility PCI CD. One Quick Start Guide

It is recommended that you read the Quick Start Guide first. All the necessary and essential information is given in the Quick Start Guide, including:

Where to get the software driver, demo programs and other resources.

How to install the software.

How to test the card. Attention! If any of these items is missing or damaged, contact the dealer from whom

you purchased the product. Please save the shipping materials and carton

in case you need to ship or store the product in the future.


2. Hardware Configuration 2.1 Board Layout

AT-BUS

CN1

SW1

J1 J2

J3

CN2

CN3

CN1 24-channel digital input/output (50-pin header, PA, PB, PC) CN2 16-channel digital input/output (20-pin header, PA, PB) CN3 8-channel digital input/output (20-pin header, PC) J1 Interrupt jumper setting J2 Interrupt status setting J3 Interrupt trigger edge setting

SW1 Base address setting


2.2 Jumper Setting

2.2.1 Interrupt Jumper Setting

2.2.2 Interrupt Status Setting

DIS: Interrupt disable (Default) PGM: Programmable interrupt enable, when PC-4 is low EN: Interrupt enable

2.2.3 Interrupt Trigger Edge Setting


2.3 Base address Setting

For Example How to select 2 C 0 (Hex) OFF 1 ON 0 X 0

2 C 0 ON OFF OFF ON ON ON ON X 0 1 1 0 0 0 0 0

1

A8 A7 A6 A5 A4 A3 A2 X

0

The detail SW1 base addresses setting. Please refer to 24-bit Address Table, as follows:


24-Bit Address Table: ( * ): Default Setting ; X = don’t care

I/O Address (Hex)

1 A8

2 A7

3 A6

4 A5

5 A4

6 A3

7 A2

8

200-203 ON ON ON ON ON ON ON X 204-207 ON ON ON ON ON ON OFF X 208-20B ON ON ON ON ON OFF ON X 20C-20F ON ON ON ON ON OFF OFF X 210-213 ON ON ON ON OFF ON ON X 214-217 ON ON ON ON OFF ON OFF X 218-21B ON ON ON ON OFF OFF ON X 21C-21F ON ON ON ON OFF OFF OFF X 220-223 ON ON ON OFF ON ON ON X 224-227 ON ON ON OFF ON ON OFF X 228-22B ON ON ON OFF ON OFF ON X 22C-22F ON ON ON OFF ON OFF OFF X 230-233 ON ON ON OFF OFF ON ON X 234-237 ON ON ON OFF OFF ON OFF X 238-23B ON ON ON OFF OFF OFF ON X 23C-23F ON ON ON OFF OFF OFF OFF X 240-243 ON ON OFF ON ON ON ON X 244-247 ON ON OFF ON ON ON OFF X 248-24B ON ON OFF ON ON OFF ON X 24C-24F ON ON OFF ON ON OFF OFF X 250-253 ON ON OFF ON OFF ON ON X 254-257 ON ON OFF ON OFF ON OFF X 258-25B ON ON OFF ON OFF OFF ON X 25C-25F ON ON OFF ON OFF OFF OFF X 260-263 ON ON OFF OFF ON ON ON X 264-267 ON ON OFF OFF ON ON OFF X 268-26B ON ON OFF OFF ON OFF ON X 26C-26F ON ON OFF OFF ON OFF OFF X 270-273 ON ON OFF OFF OFF ON ON X 274-277 ON ON OFF OFF OFF ON OFF X 278-27B ON ON OFF OFF OFF OFF ON X 27C-27F ON ON OFF OFF OFF OFF OFF X 280-283 ON OFF ON ON ON ON ON X 284-287 ON OFF ON ON ON ON OFF X 288-28B ON OFF ON ON ON OFF ON X 28C-28F ON OFF ON ON ON OFF OFF X 290-293 ON OFF ON ON OFF ON ON X 294-297 ON OFF ON ON OFF ON OFF X 298-29B ON OFF ON ON OFF OFF ON X 29C-29F ON OFF ON ON OFF OFF OFF X 2A0-2A3 ON OFF ON OFF ON ON ON X


2A4-2A7 ON OFF ON OFF ON ON OFF X 2A8-2AB ON OFF ON OFF ON OFF ON X 2AC-2AF ON OFF ON OFF ON OFF OFF X 2B0-2B3 ON OFF ON OFF OFF ON ON X 2B4-2B7 ON OFF ON OFF OFF ON OFF X 2B8-2BB ON OFF ON OFF OFF OFF ON X 2BC-2BF ON OFF ON OFF OFF OFF OFF X

2C0-2C3(*) ON OFF OFF ON ON ON ON X 2C4-2C7 ON OFF OFF ON ON ON OFF X 2C8-2CB ON OFF OFF ON ON OFF ON X 2CC-2CF ON OFF OFF ON ON OFF OFF X 2D0-2D3 ON OFF OFF ON OFF ON ON X 2D4-2D7 ON OFF OFF ON OFF ON OFF X 2D8-2DB ON OFF OFF ON OFF OFF ON X 2DC-2DF ON OFF OFF ON OFF OFF OFF X 2E0-2E3 ON OFF OFF OFF ON ON ON X 2E4-2E7 ON OFF OFF OFF ON ON OFF X 2E8-2EB ON OFF OFF OFF ON OFF ON X 2EC-2EF ON OFF OFF OFF ON OFF OFF X 2F0-2F3 ON OFF OFF OFF OFF ON ON X 2F4-2F7 ON OFF OFF OFF OFF ON OFF X 2F8-2FB ON OFF OFF OFF OFF OFF ON X 2FC-2FF ON OFF OFF OFF OFF OFF OFF X

300-303 OFF ON ON ON ON ON ON X 304-307 OFF ON ON ON ON ON OFF X 308-30B OFF ON ON ON ON OFF ON X 30C-30F OFF ON ON ON ON OFF OFF X 310-313 OFF ON ON ON OFF ON ON X 314-317 OFF ON ON ON OFF ON OFF X 318-31B OFF ON ON ON OFF OFF ON X 31C-31F OFF ON ON ON OFF OFF OFF X 320-323 OFF ON ON OFF ON ON ON X 324-327 OFF ON ON OFF ON ON OFF X 328-32B OFF ON ON OFF ON OFF ON X 32C-32F OFF ON ON OFF ON OFF OFF X 330-333 OFF ON ON OFF OFF ON ON X 334-337 OFF ON ON OFF OFF ON OFF X 338-33B OFF ON ON OFF OFF OFF ON X 33C-33F OFF ON ON OFF OFF OFF OFF X 340-343 OFF ON OFF ON ON ON ON X 344-347 OFF ON OFF ON ON ON OFF X 348-34B OFF ON OFF ON ON OFF ON X 34C-34F OFF ON OFF ON ON OFF OFF X 350-353 OFF ON OFF ON OFF ON ON X 354-357 OFF ON OFF ON OFF ON OFF X 358-35B OFF ON OFF ON OFF OFF ON X 35C-35F OFF ON OFF ON OFF OFF OFF X


360-363 OFF ON OFF OFF ON ON ON X 364-367 OFF ON OFF OFF ON ON OFF X 368-36B OFF ON OFF OFF ON OFF ON X 36C-36F OFF ON OFF OFF ON OFF OFF X 370-373 OFF ON OFF OFF OFF ON ON X 374-377 OFF ON OFF OFF OFF ON OFF X 378-37B OFF ON OFF OFF OFF OFF ON X 37C-37F OFF ON OFF OFF OFF OFF OFF X 380-383 OFF OFF ON ON ON ON ON X 384-387 OFF OFF ON ON ON ON OFF X 388-38B OFF OFF ON ON ON OFF ON X 38C-38F OFF OFF ON ON ON OFF OFF X 390-393 OFF OFF ON ON OFF ON ON X 394-397 OFF OFF ON ON OFF ON OFF X 398-39B OFF OFF ON ON OFF OFF ON X 39C-39F OFF OFF ON ON OFF OFF OFF X 3A0-3A3 OFF OFF ON OFF ON ON ON X 3A4-3A7 OFF OFF ON OFF ON ON OFF X 3A8-3AB OFF OFF ON OFF ON OFF ON X 3AC-3AF OFF OFF ON OFF ON OFF OFF X 3B0-3B3 OFF OFF ON OFF OFF ON ON X 3B4-3B7 OFF OFF ON OFF OFF ON OFF X 3B8-3BB OFF OFF ON OFF OFF OFF ON X 3BC-3BF OFF OFF ON OFF OFF OFF OFF X 3C0-3C3 OFF OFF OFF ON ON ON ON X 3C4-3C7 OFF OFF OFF ON ON ON OFF X 3C8-3CB OFF OFF OFF ON ON OFF ON X 3CC-3CF OFF OFF OFF ON ON OFF OFF X 3D0-3D3 OFF OFF OFF ON OFF ON ON X 3D4-3D7 OFF OFF OFF ON OFF ON OFF X 3D8-3DB OFF OFF OFF ON OFF OFF ON X 3DC-3DF OFF OFF OFF ON OFF OFF OFF X 3E0-3E3 OFF OFF OFF OFF ON ON ON X 3E4-3E7 OFF OFF OFF OFF ON ON OFF X 3E8-3EB OFF OFF OFF OFF ON OFF ON X 3EC-3EF OFF OFF OFF OFF ON OFF OFF X 3F0-3F3 OFF OFF OFF OFF OFF ON ON X 3F4-3F7 OFF OFF OFF OFF OFF ON OFF X 3F8-3FB OFF OFF OFF OFF OFF OFF ON X 3FC-3FF OFF OFF OFF OFF OFF OFF OFF X


2.4 Pin Assignments The CN1 of DIO-24 emulate as Intel 8255 general purpose programmable peripheral interface. Figure shows DIO-24 I/O port equally block diagram.

DIO-24 Block diagram

Port A 8-bit

Port B 8-bit

Port C Two 4-bit

CN

1

8255 PPI

DIO-24

Note: When computer is powered on, the DIO-24 default status is input mode.



PB 7

20 18 16 14 12 10 8 6 4

171513119 7 5 3 1

19

PB 5PB 6GND

VccGND+12V

PA 7PA 5

PB 1PB 3

PB 0PA 6

PB 2PB 4

PA 2PA 4

PA 3PA 0 2 PA 1

NC

20 18 16 14 12 10 8 6 4

171513119 75 3 1

19

NC NC

GNDVcc

GND+12V

PC 7PC 5

NCNC

NCPC 6

NCNC

PC 2PC 4

PC 3PC 0 2 PC 1

GND

20 18 16 14 12 10 8 6 4

17 15 13 11 9 7 5 3 1

19

GNDPC_0PB_7PB_6

GNDGND

GNDGND

GNDGND

PC_3PC_4

PC_2PC_1

PC_6PC_5

GNDPC_7

2 GND

37 35 33 31 29 27 25 23 21

39

PA_6PA_5PA_4

PB_1PB_2

PB_0PA_7

PB_4PB_3

PB_5

45 43 41

49

PA_1PA_0

+5V

PA_3PA_2

47

GND

40 38 36 34 32 30 28 26 24

GND

GNDGND

GNDGND

GNDGND

GND

22 GND

GND

50 48 46 44 42

GND

GNDGND

GND

CN1: 50-Pin of box header CN2: 20-Pin of box header

CN3 20-Pin of box header

All Signals are TTL Compatible

High (1) 2.0 ~ 5.0 V(Voltage over 5.0V will damage the device)

None Define 2.0 V ~ 0.8 V

Low(0) Under 0.8 V

3. Programming The DIO-24 emulates MODE 0 of the 8255, and Mode 0 of the 8255 provides basic input and output operations through each of the ports A, B and C. Output data is latched and input data follows the peripheral. Mode 0 of the 8255 PPI functions

16 different configurations Two 8-bit port and two 4 bit-ports Input are not latched Output are latched

3.1 Register

The DIO-24 each port can be defined to input or output mode.

Register Functions

Address Register Read/Write Base+0 Port A R/W Base+1 Port B R/W Base+2 Port C R/W

Base+3 CFG Write only

CFG Register Format

D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 ? ? 0 ? ? 1 X X Port A

1:Input 0:Output

Port C 1:Input 0:Output (High nibble)

X Port B 1:Input 0:Output

Port C 1:Input 0:Output (Low nibble)


CFG Configurations Table

D4 D3 D1 D0 CFG PA0-PA7 PC4-PC7 PB0-PB7 PC0-PC3

80H O O O O 81H O O O I 82H O O I O 83H O O I I 88H O I O O 89H O I O I 8AH O I I O 8BH O I I I 90H I O O O 91H I O O I 92H I O I O 93H I O I I 98H I I O O 99H I I O I 9AH I I I O 9BH I I I I


3.2 Interrupt Handling

The Port C 0 can generate a hardware interrupt to computer. Use the interrupt you must set an IRQ level to be used. The J1 is used to select the IRQ level and the J2 is used to select the desired interrupt enable mode. Then the J3 is used to select rising edge trigger or falling edge trigger.

3.3 Output Latch The signal direction of DIO-24 is software programmable. When user turns on or reset computer, all ports are configured as input mode. When the DIO-24 is programmed as output mode, it does not output until program execute the output instruction.

Output Buffer Output Latch

Input Buffer

Output Enable

External D

ata Bus

Signal Direction


3.4 Program Example The DIO-24 I/O card is very easy to programming input/ output function. Example (Quick Basic) Bas=&H2C0 ‘====== Init DIO-24 Port A and Port B Input mode Port C output mode =====

OUT Bas+3,&H92 ‘Reference Configuration table ‘==================================================

PA = INP(Bas+0) ‘Read Port A Data PB = INP(Bas+1) ‘Read Port B Data OUT Bas+2 , &HFF ‘Rrite Data to Port C , set Channel 0-7 is high OUT Bas+3,&H80 ‘ Set Port A,B,C is Output Mode OUT Bas+0, 0 ‘ Write Data to Port A OUT Bas+1, 0 ‘ Write Data to port B OUT Bas+2, 0 ‘ Write Data to Port C OUT Base+3,&H9B ‘ Set Port A,B,C is Input mode PA=INP(Bas+0) ‘ Read Port A Data

PB=INP(Bas+1) ‘ Read Port B Data PC=INP(Bas+2) ‘ Read Port C Data


4. Software/Hardware Installation The DIO-24 can be used in DOS and Windows 98/ME/NT/2K and 32-bit Windows XP/2003/Vista/7. The recommended installation procedure for windows is given in Sec. 4.1 ~ 4.2. Or refer to Quick Start Guide (CD:\NAPDOS\ISA\DIO\Manual\QuickStart\). http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/manual/quickstart/

4.1 Software Installing Procedure DIO-24 Windows driver (Windows 98/NT/2K and 32-bit Windows XP/2003/ Vista/7):

Step 1: Insert the companion CD into the CD-ROM drive and after a few seconds the installation program should start automatically. If it doesn’t start automatically for some reason, double-click the AUTO32.EXE file in the NAPDOS folder on this CD.

Step 2: Click the item: “Install Toolkits (Softwares)/Manuals”.

Step 3: Click the item: “ISA Bus DAQ Card”.

Step 4: Click the item: “DIO”.

Step 5: Choose the “Install Toolkit for Windows 95/98、NT or 2000” for setup according to your PC platform and then install driver.

Notes:

1. The DIO-24 Windows driver site location:

http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/dll/

2. The Windows 2000 (Win2K) driver support Windows 2000 and 32-bit

Windows XP/2003/Vista/7.


http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/manual/quickstart/


Step 6: Click “Next>” button to start installation. Step 7: Click “Next>” button to install driver into the default folder. Step 8: Click “Next>” button to continue installation. Step 9: Select “No, I will restart my computer late” and then click “Finish”

button. 4.2 Hardware Installing Procedure Please set the base address, interrupt IRQ and interrupt status on the DIO-24 card before insert DIO-24 card into the ISA slot in the computer. For detailed base address and interrupt settings information refer to Section 2.2 “Jumper Setting” and 2.3 “Base Address Setting”. For example: base address is 0x2C0, Interrupt IRQ is 7. Step 1: Shout down and power off your computer. Step 2: Remove all covers from the computer. Step 3: Select an empty ISA slot. Step 4: Care fully insert your DIO-24 card into the ISA slot. Step 5: Replace the PC covers. Step 6: Power on the computer.


Adding Hardware Notes: adding hardware for working on Windows 2000 and 32-bit Windows XP/2003/Vista/7 only. Windows 95/98/Me/NT users should install correct version of the driver on the CD-ROM, and skip these “Adding Hardware” procedures.

Step 7: Open the “Control Panel” by click the item “Start >> Settings >>

Control Panel ”.

Step 8: Double-click the item “Add Hardware” and click

the “Next>” button.

Step 9: Select the item “Yes, I have already connected

the hardware” and click the “Next>” button.

Step 10: Selection the item “Add a new hardware device” and click the

“Next>” button.

Step 11: Selection the item “Install the hardware that I manually select from

a list [Advanced]” and click the “Next>” button.

Step 12: Selection the item “Show All Devices” and click the “Next>” button.

Step 13: Click the “Have Disk...” button.

Step 14: Click the “Browse...” button to select the .Inf file default path is

C:\DAQPRO\DIO_Win2K\Inf and click the “Open” and “OK” button.


Step 15: Selection then correct device from the “Models:” listbox and click the

“Next>” button.

Step 16: Click the “Next>” button and then click the “Finish” button. Modify the device properties

Step 17: Double-click the “System” icon in the

“Control Panel”.

Step 18: Click the “Hardware” tab and then click the “Device Manager” button.

Step 19: Click the “DAQCard” tab and then double-click “ICPDAS DIO-24

Digital I/O Card”.

Step 20: Select the “Resources” tab and then setting as follows:

Complete

6. Select IRQ

8. Check the Conflict information

7. Change to IRQ set by J1


4. Change to base address set by SW1

3. Click 2. Uncheck

1. Select I/O Range


DIO-96/DIO-144 96/144-bit OPTO-22 Compatible DIO Board 96/144-bit OPTO-22 Compatible DIO Board

5. Software Installation 5. Software Installation The DIO-144/96 provides 144/ 96 TTL digital I/O lines. It emulates six channel 8255 mode 0 (basic input /output mode) and has an increased output current of 15 mA (source) and 64 mA (sink) for controlling LED, relay, etc. The DIO-144/96 each connector consists of three 8-bit bi-directional ports and two input lines for interrupt enable and interrupt. The 8-bit ports are named port A (PA), port B (PB) and port C (PC). The port C can be split into two nibbles wide ports. All ports are configured as inputs upon power-up or reset. The DIO-144/96 uses 4 consecutive I/O locations in I/O addressing space. The base address is selectable by using an 8-position DIP switch from 200 to 3FF hex. The interrupt signal can be connected to any of the interrupt levels 2 through 15 available on the PC bus via a jumper.

The DIO-144/96 provides 144/ 96 TTL digital I/O lines. It emulates six channel 8255 mode 0 (basic input /output mode) and has an increased output current of 15 mA (source) and 64 mA (sink) for controlling LED, relay, etc. The DIO-144/96 each connector consists of three 8-bit bi-directional ports and two input lines for interrupt enable and interrupt. The 8-bit ports are named port A (PA), port B (PB) and port C (PC). The port C can be split into two nibbles wide ports. All ports are configured as inputs upon power-up or reset. The DIO-144/96 uses 4 consecutive I/O locations in I/O addressing space. The base address is selectable by using an 8-position DIP switch from 200 to 3FF hex. The interrupt signal can be connected to any of the interrupt levels 2 through 15 available on the PC bus via a jumper. 5.1 Features 5.1 Features

144/ 96 digital I/O lines OPTO-22 pin compatible Programmable interrupt handling Buffer output for higher driving capability than the 8255 Register compatible to 722 series

5.2 Applications

Interfacing with any OPTO-22 compatible I/O module Digital I/O control Contact closure monitoring and alarm monitoring Useful with parallel interface devices


5.3 Specifications Model Name DIO-96 DIO-144 Digital Input Channels 96 (OPTO-22 compatible) 144 (OPTO-22 compatible) Compatibility 5 V/TTL Input Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min. Response Speed 1.0 MHz (Typical) Digital Output Channels 96 (OPTO-22 compatible) 144 (OPTO-22 compatible) Compatibility 5 V/TTL Output Voltage Logic 0: 0.4 V max.

Logic 1: 2.4 V min. Output Capability Sink: 0.8 mA @ 0.8 V

Source: -2.4 mA @ 2.0 V Response Speed 1.0 MHz (Typical) General Bus Type ISA I/O Connector 50-pin box header x 4 50-pin box header x 6 Dimensions (L x W x D) 182 mm x 120 mm x 22 mm Power Consumption 800 mA @ +5 V 700 mA @ +5 V Operating Temperature 0 ~ 60 °C Storage Temperature -20 ~ 70 °C Humidity 5 ~ 85% RH, non-condensing


5.4 Product Check List The shipping package includes the following items:

One DIO-144/96 card One software utility PCI CD. One Quick Start Guide

It is recommended that you read the Quick Start Guide first. All the necessary and essential information is given in the Quick Start Guide, including:

Where to get the software driver, demo programs and other resources.

How to install the software.

How to test the card. Attention! If any of these items is missing or damaged, contact the dealer from whom

you purchased the product. Please save the shipping materials and carton

in case you need to ship or store the product in the future.



6. Hardware Configuration on

6.1 Board Layout 6.1 Board Layout

JP0 Interrupt status setting for CH0JP1 Interrupt status setting for CH1 JP2 Interrupt status setting for CH2 JP3 Interrupt status setting for CH3 JP4 Interrupt status setting for CH4 JP5 Interrupt status setting for CH5 JP7 96-bit or 144-bit setting JP6 Interrupt jumper setting SW1 Base address setting

JP6 (IRQ)

JP0 JP1JP2JP3JP4 JP5

SW1

JP7

ISA BUS

DIO-144 only

6.2 Jumper Setting

6.2.1 Interrupt Jumper Setting

6.2.2 Interrupt Status Setting D: Interrupt disable (Default) P: Programmable Interrupt enable, when PC-4 is low E: Interrupt enable

6.2.3 96-bit/144-bit Jumper Setting The DIO-144/96 provides 144/96 bit mode. The 144 bit mode (Channel 0-5) requires 24 consecutive locations in I/O address space, the 96 bit mode (Channel 0-3) requires 16 consecutive locations in I/O address space.

J7

96-bit


6.3 Base Address Setting 6.3.1 96-bit Mode

For Example How to select 2 C 0 (Hex) OFF 1 ON 0

2 C 0 OFF ON OFF OFF ON ON

1 0 1 1 0 0 A9 A8 A7 A6 A5 A4

The detail SW1 base addresses setting. Please refer to 96-Bit Address Table, as follows.


96-Bit Address Table: (*): Default Setting I/O Address 1

A9 2

A8 3

A7 4

A6 5

A5 6

A4 200 OFF ON ON ON ON ON 210 OFF ON ON ON ON OFF 220 OFF ON ON ON OFF ON 230 OFF ON ON ON OFF OFF 240 OFF ON ON OFF ON ON 250 OFF ON ON OFF ON OFF 260 OFF ON ON OFF OFF ON 270 OFF ON ON OFF OFF OFF 280 OFF ON OFF ON ON ON 290 OFF ON OFF ON ON OFF 2A0 OFF ON OFF ON OFF ON 2B0 OFF ON OFF ON OFF OFF

2C0 (*) OFF ON OFF OFF ON ON 2D0 OFF ON OFF OFF ON OFF 2E0 OFF ON OFF OFF OFF ON 2F0 OFF ON OFF OFF OFF OFF

300 OFF OFF ON ON ON ON 310 OFF OFF ON ON ON OFF 320 OFF OFF ON ON OFF ON 330 OFF OFF ON ON OFF OFF 340 OFF OFF ON OFF ON ON 350 OFF OFF ON OFF ON OFF 360 OFF OFF ON OFF OFF ON 370 OFF OFF ON OFF OFF OFF 380 OFF OFF OFF ON ON ON 390 OFF OFF OFF ON ON OFF 3A0 OFF OFF OFF ON OFF ON 3B0 OFF OFF OFF ON OFF OFF 3C0 OFF OFF OFF OFF ON ON 3D0 OFF OFF OFF OFF ON OFF 3E0 OFF OFF OFF OFF OFF ON 3F0 OFF OFF OFF OFF OFF OFF


6.3.2 144-bit Mode

For Example How to select 2 C 0 (Hex) OFF 1 ON 0 X 0

2 C 0 OFF ON OFF OFF ON X

1 0 1 1 0 0 A9 A8 A7 A6 A5 X

The detail SW1 base addresses setting. Please refer to 144-Bit Address Table, as follows.


144-Bit Address Table: (*): Default setting I/O Address 1

A9 2

A8 3

A7 4

A6 5

A5 6 X

200 OFF ON ON ON ON X 220 OFF ON ON ON OFF X 240 OFF ON ON OFF ON X 260 OFF ON ON OFF OFF X 280 OFF ON OFF ON ON X 2A0 OFF ON OFF ON OFF X

2C0 (*) OFF ON OFF OFF ON X 2E0 OFF ON OFF OFF OFF X

300 OFF OFF ON ON ON X 320 OFF OFF ON ON OFF X 340 OFF OFF ON OFF ON X 360 OFF OFF ON OFF OFF X 380 OFF OFF OFF ON ON X 3A0 OFF OFF OFF ON OFF X 3C0 OFF OFF OFF OFF ON X 3E0 OFF OFF OFF OFF OFF X



6.4 Pin Assignments The CN0 of DIO-144/96 emulates as Intel 8255 general purposes programmable peripheral interface. Figure shows DIO-144/96 I/O port equally block diagram.

Emulated 8255 circle

DIO-144 DIO- 96

Port A 8-bit

Port B 8-bit

Port C Two 4-bit

CH

0

JP0

VCC

D P E

Interrupt Controller

PC4 PC0 (Interrupt Signal)

IRQ Level

(Interrupt controller Gate)

JP6

When the Interrupt controller gate is logic low, the interrupt controller will be enabled


GND

201816141210864

171513119 753 1

19

GNDPC_0PB_7PB_6

GNDGND

GNDGND

GNDGND

PC_3PC_4

PC_2PC_1

PC_6PC_5

GNDPC_7

2 GND

373533312927252321

39

PA_6PA_5PA_4

PB_1PB_2

PB_0PA_7

PB_4PB_3

PB_5

454341

49

PA_1PA_0

+5V

PA_3PA_2

47

GND

403836343230282624

GND

GNDGND

GNDGND

GNDGND

GND

22 GND

GND

5048464442

GND

GNDGND

GND

All Signals are TTL Compatible

High (1) 2.0 ~ 5.0 V(Voltage over 5.0V will damage the device)

None Define 2.0 V ~ 0.8 V

Low(0) Under 0.8 V

CN1: 50-Pin of box header for CH0~CH5

7. Programming Programming The DIO-144/96 offers six/four OPTO-22 connectors, which are emulated MODE 0 of the 8255. Mode 0 of the 8255 provides basic input and output operations through each of the ports A, B and C. Output data is latched and input data follows the peripheral.

The DIO-144/96 offers six/four OPTO-22 connectors, which are emulated MODE 0 of the 8255. Mode 0 of the 8255 provides basic input and output operations through each of the ports A, B and C. Output data is latched and input data follows the peripheral. Mode 0 of the 8255 PPI Functions Mode 0 of the 8255 PPI Functions

16 different configurations 16 different configurations Two 8-bit port and two 4-bit-ports Two 8-bit port and two 4-bit-ports Input are not latched Input are not latched Output are latched Output are latched

7.1 Register 7.1 Register

I/O Address Channel 144 Bit Mode 2C0 ~ 2DF CH0 ~ CH 5 96 Bit Mode 2C0 ~2CF CH0 ~CH3

144 Bit Mode I/O Register Default I/O Address: 0x2C0 (Hex)

Address (Hex.) Register Read/Write Base+0x00 CH0_Port A R/W Base+0x01 CH0_Port B R/W Base+0x02 CH0_Port C R/W Base+0x03 CH0_CFG Write only

Base+0x04 CH1_Port A R/W Base+0x05 CH1_Port B R/W Base+0x06 CH1_Port C R/W Base+0x07 CH1_CFG Write only

Base+0x08 CH2_Port A R/W Base+0x09 CH2_Port B R/W Base+0x0A CH2_Port C R/W


Base+0x0B CH2_CFG Write only

Base+0x0C CH3_Port A R/W Base+0x0D CH3_Port B R/W Base+0x0E CH3_Port C R/W Base+0x0F CH3_CFG Write only



96 Bit Mode I/O Register Default I/O Address : 0x2C0(Hex)

Address (Hex.) Register Read/Write Base+0x00 CH0_Port A R/W Base+0x01 CH0_Port B R/W Base+0x02 CH0_Port C R/W Base+0x03 CH0_CFG Write only


Base+0x08 CH2_Port A R/W Base+0x09 CH2_Port B R/W Base+0x0A CH2_Port C R/W Base+0x0B CH2_CFG Write only

Base+0x0C CH3_Port A R/W Base+0x0D CH3_Port B R/W Base+0x0E CH3_Port C R/W Base+0x0F CH3_CFG Write only


7.2 Data Format The DIO-144/96 provides 6/4 channel opto-22 connectors and each channel have 3 digital input/output port. Each port could be programmed as input or output mode by CFG register.

CFG Register Format

D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 ? ? 0 ? ? 1 X X Port A

1:Input 0:Output

Port C 1:Input 0:Output (High nibble)

X Port B 1:Input 0:Output

Port C 1:Input 0:Output (Low nibble)

CFG Configurations Table

D4 D3 D1 D0 CFG PA0-PA7 PC4-PC7 PB0-PB7 PC0-PC3

80H O O O O 81H O O O I 82H O O I O 83H O O I I 88H O I O O 89H O I O I 8AH O I I O 8BH O I I I 90H I O O O 91H I O O I 92H I O I O 93H I O I I 98H I I O O 99H I I O I 9AH I I I O 9BH I I I I


The DIO-144/96 each port can be CFG register initial to input port or output port. The port A and port B is 1 byte (1 byte = 8 bits) and the port C is 2 nibble byte (nibble byte = 4 bits).

Input / Output Port Data Format

Port_A Port_A_7 Port_A_6 Port_A_5 Port_A_4 Port_A_3 Port_A_2 Port_A_1 Port_A_0

D7 D6 D5 D4 D3 D2 D1 D0

Port_B Port_B_7 Port_B_6 Port_B_5 Port_B_4 Port_B_3 Port_B_2 Port_B_1 Port_B_0

D7 D6 D5 D4 D3 D2 D1 D0

Port_C Port_C_7 Port_ C _6 Port_ C _5 Port_ C _4 Port_ C _3 Port_ C _2 Port_ C _1 Port_ C _0

High nibble3

High nibble2

High nibble1

High nibble0

Low nibble3

Low nibble2

Low nibble1

Low nibble0

D7 D6 D5 D4 D3 D2 D1 D0 Example: Initialize 1. Initial channel 0 Port A input mode, Port B input mode, Port C output mode

1-1: Reference I/O register table: channel 0 CFG = Base + 0x03 1-2: Reference CFG format table: Port_A_I, Port_B_I, Port_C_O = 0x92 Note :

Port_A_I means: Port A Input mode

Port_C_O means: Port C Output mode

1-3: Output initial data to CFG register: outportb ( Base + 0x03 , 0x92); 1-4: Then you can reading data from Port A and Port B and output data to Port C

of channel 0

2. Initial channel 1 port A output mode , port B output mode , port C input mode 2-1: Reference I/O register table: channel CFG = Base + 0x07 2-2: Reference CFG format table: Port_A_O, Port_B_O, Port_C_I = 0x89 2-3: Output initial data to CFG register: outputb (Base +0x07 , 0x89); 2-4: Then you can output data to port A and port B and reading data from port C

3. Other channel initialize as same as step 1 and step2.


7.3 Interrupt Handling The Port C_0 of each connector can generate a hardware interrupt to computer. Use the interrupt you must set the IRQ level to be used. The JP6 is used to select IRQ level and the JP0 ~ JP6 is used to select the desired interrupt enable mode.

7.4 Output Latch The DIO-144/96 signal direction is software programmable. When users turn on or reset computer, all ports are configured as input mode. When the DIO-144/96 is programmed as output mode, it does not output until program execute the output instruction.

Output Buffer Output Latch

Input Buffer

External

Output Enable

Data B

us

Signal Direction


7.5 Program Example The DIO-144/96 I/O card is very easy to programming input/Output function. Example (Quick Basic) Bas=&H2C0 ‘==== Init DIO-144/96 Port A and Port B Input mode Port C output mode ====

OUT Bas+3,&H92 ‘ Reference Configuration table ‘==================================================

PA = INP(Bas+0) 　’Read Port A Data PB = INP(Bas+1) 　’Read Port B Data OUT Bas+2 , &HFF 　’Write Data to Port C , set Channel 0 ~ 7 is high ‘================ initial channel 1 ===================

OUT Bas+7,&H80 ‘ Set Port A,B,C is Output Mode

OUT Bas+4, 0 ‘ Write Data to Port A OUT Bas+5, 0 ‘ Write Data to port B OUT Bas+6, 0 ‘ Write Data to Port C ‘====================initial channel 2 ====================

OUT Base+&HB,&H9B ‘ Set Port A,B,C is Input mode PA=INP(Bas+&H8) ‘ Read Port A Data PB=INP(Bas+&H9) ‘ Read Port B Data PC=INP(Bas+&HA) ‘ Read Port C Data


8. Software/Hardware Installation Software/Hardware Installation The DIO-144/96 can be used in DOS and Windows 98/ME/NT/2K and 32-bit Windows XP/2003/Vista/7. The recommended installation procedure for windows is given in Sec. 8.1 ~ 8.2. Or refer to Quick Start Guide (CD:\NAPDOS\ISA\DIO\Manual\QuickStart\).

The DIO-144/96 can be used in DOS and Windows 98/ME/NT/2K and 32-bit Windows XP/2003/Vista/7. The recommended installation procedure for windows is given in Sec. 8.1 ~ 8.2. Or refer to Quick Start Guide (CD:\NAPDOS\ISA\DIO\Manual\QuickStart\). http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/manual/quickstart/http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/manual/quickstart/

8.1 Software Installing Procedure DIO-144/96 Windows driver (Windows 98/NT/2K and 32-bit Windows XP/2003/ Vista/7):

Step 1: Insert the companion CD into the CD-ROM drive and after a few seconds the installation program should start automatically. If it doesn’t start automatically for some reason, double-click the AUTO32.EXE file in the NAPDOS folder on this CD.

Step 2: Click the item: “Install Toolkits (Softwares)/Manuals”.

Step 3: Click the item: “ISA Bus DAQ Card”.

Step 4: Click the item: “DIO”.

Step 5: Choose the “Install Toolkit for Windows 95/98、NT or 2000” for setup according to your PC platform and then install driver.

Notes:

3. The DIO-144/96 Windows driver site location:


4. The Windows 2000 (Win2K) driver support Windows 2000 and 32-bit

Windows XP/2003/Vista/7.


http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/manual/quickstart/


Step 6: Click “Next>” button to start installation. Step 7: Click “Next>” button to install driver into the default folder. Step 8: Click “Next>” button to continue installation. Step 9: Select “No, I will restart my computer late” and then click “Finish”

button. 8.2 Hardware Installing Procedure Please set the base address, interrupt IRQ and interrupt status on the DIO-144/96 card before insert DIO-144/96 card into the ISA slot in the computer. For detailed base address and interrupt settings information refer to Section 6.2 “Jumper Setting” and 6.3 “Base Address Setting”. For example: base address is 0x2C0, Interrupt IRQ is 7. Step 1: Shout down and power off your computer. Step 2: Remove all covers from the computer. Step 3: Select an empty ISA slot. Step 4: Care fully insert your DIO-144/96 card into the ISA slot. Step 5: Replace the PC covers. Step 6: Power on the computer.


Adding Hardware Notes: adding hardware for working on Windows 2000 and 32-bit Windows XP/2003/Vista/7 only. Windows 95/98/Me/NT users should install correct version of the driver on the CD-ROM, and skip these “Adding Hardware” procedures.

Step 7: Open the “Control Panel” by click the item “Start >> Settings >>

Control Panel ”.

Step 8: Double-click the item “Add Hardware” and click

the “Next>” button.

Step 9: Select the item “Yes, I have already connected

the hardware” and click the “Next>” button.

Step 10: Selection the item “Add a new hardware device” and click the

“Next>” button.

Step 11: Selection the item “Install the hardware that I manually select from

a list [Advanced]” and click the “Next>” button.

Step 12: Selection the item “Show All Devices” and click the “Next>” button.

Step 13: Click the “Have Disk...” button.

Step 14: Click the “Browse...” button to select the .Inf file default path is

C:\DAQPRO\DIO_Win2K\Inf and click the “Open” and “OK” button.



Step 15: Selection then correct device from the “Models:” listbox and click the

“Next>” button.

Step 16: Click the “Next>” button and then click the “Finish” button. Modify the device properties

Step 17: Double-click the “System” icon in the

“Control Panel”.

Step 18: Click the “Hardware” tab and then click the “Device Manager” button.

Step 19: Click the “DAQCard” tab and then double-click “ICPDAS DIO-144

Digital I/O Card”.

Step 20: Select the “Resources” tab and then setting as follows:

1. Select I/O Range

2. Uncheck 3. Click

4. Change to base address set by SW1


7. Change to IRQ set by J6


6. Select IRQ

Complete

Appendix: Daughter Board A1. Daughter Board Comparison Table A1. Daughter Board Comparison Table 20-pin flat-cable 50-pin flat-cable D-sub 37-pin DB-37 No No Yes DN-37 No No Yes ADP-37/PCI No Yes Yes ADP-50/PCI No Yes No DB-24P No Yes No DB-24PD No Yes Yes DB-16P8R No Yes Yes DB-24R No Yes No DB-24RD No Yes Yes DB-24C Yes Yes Yes DB-24PR Yes Yes No Db-24PRD No Yes Yes DB-24POR Yes Yes Yes DB-24SSR No Yes Yes The DIO-24 and DIO-144/96 offers 50 pin Opto-22 connector which could be connected to daughter board, such as: 1. DB-24PD: 24 OPTO-isolated Digital Input Terminal Board. 2. DB-24RD: 24 Relay Output Board 3. DB-24PRD: 24 Power Relay Output Board


A2. DB-24P/24PD Isolated Input Board The DB-24P/24PD is a 24-channel isolated digital input daughter board. The optically isolated inputs of the DB-24P/24PD consist of a bi-directional optocoupler with a resistor for current sensing. You can use the DB-24P/24PD to sense DC signal from TTL levels up to 24 V or use the DB-24P to sense a wide range of AC signals. You can use this board to isolate the computer from large common-mode voltage, ground loops and transient voltage spike that often occur in industrial environments.

DIO-144/96/24

DIO-144/96/24

AC or DC Signal 0 V to 24 V

Opto-Isolated

DB-24P DB-24P DB-24PD 50-pin flat-cable header Yes Yes D-sub 37-pin header No Yes Other specifications Same



A3. DB-24R/24RD Relay Board The DB-24R/DB-24RD, 24-channel relay output board, consists of 24 form C relays for efficient switch of load by programmed control. The relay are energized by apply 12 V/24 V voltage signal to the appropriated relay channel on the 50-pin flat connector. There are 24 enunciator LEDs for each relay, light when their associated relay is activated. DB-24R DB-24RD 50-pin flat-cable header Yes Yes D-sub 37-pin header No Yes Other specifications Same DB-24R, DB-24RD 24 × Relay (120 V, 0.5 A) DB-24PR,DB-24PRD 24 × Power Relay (250 V, 5 A) DB-24POR 24 × Photo MOS Relay (350 V, 01 A) DB-24SSR 24 × SSR (250 VAC, 4 A) DB-24C 24 × O.C. (30 V, 100 mA) DB-16P8R 16 × Relay (120 V, 0.5 A) + 8 × isolated input

DIO-144/96/24

A4. DB-24PR/24PRD DB-24PR 24 × Power relay, 5 A/250 V DB-24POR 24 × Photo MOS relay, 0.1 A/350 VAC DB-24C 24 × Open Collector, 100 mA per channel, 30 V max. The DB-24PR, 24-channel power relay output board, consists of 8 form C and 16 form A electromechanical relays for efficient switching of load programmed control. The contact of each relay can control a 5 A load at 250 VAC /30 VDC. The relay is energized by applying 5 V signal to the appropriate relay channel on the 20-pin flat cable connector (just used 16 relays) or 50-pin flat cable connector (OPTO-22 compatible, for DIO-24 series). Twenty-four enunciator LEDs, one of each relay, light when their associated relay is activated. To avoid overloading your PC power supply, this board needs a +12 VDC or +24 VAC external power supply.

DB-24PR

DIO-144/96/24

50-Pin cable

Normal Open

Form A Relay

Com.

Notes: Channel : 8 form C relays (SPDT) and 16 form A relay Relay: Switch up to 5 A at 250 VAC / 5 A at 30 VDC


dio-24 dio-96/144 user manual nov. 2011 version 2 · dio-24 24-bit compatible dio opto-22 board....

Documents