dimensioning engineering108.com
DESCRIPTION
Dimensioning Engineering108.ComTRANSCRIPT
![Page 1: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/1.jpg)
Project FUNDAH e a r i t L e a r n i t
Let’s make engineering more easyJoin us
engineering108.com
![Page 2: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/2.jpg)
Dimensioning
engineering108.com
![Page 3: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/3.jpg)
TOPICS
engineering108.com
Introduction
Dimensioning components
Dimensioning object’ s features
Placement of dimensions.
![Page 4: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/4.jpg)
Introduction
engineering108.com
![Page 5: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/5.jpg)
ShapeMultiviewDrawing
Dimensioning
Designa part
1. Size, Location
ENGINEERING DESIGN
2. Non-graphic information
TRANSFERREDINFORMATION
Createdrawings
Manufacture
RESULT
Sketchesof ideas
PROCESS
engineering108.com
![Page 6: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/6.jpg)
DEFINITION
engineering108.com
Dimensioning is the process of specifying part’ s
information by using of figures, symbols and notes.
This information are such as:
1. Sizes and locations of features
2. Material’s type
3. Number required
4. Kind of surface finish
5. Manufacturing process
6. Size and geometric tolerances
![Page 7: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/7.jpg)
DimensioningComponents
engineering108.com
![Page 8: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/8.jpg)
DIMENSIONING COMPONENTS
Extension lines
Dimension lines(with arrowheads)
Leader lines
Dimension figures
Notes :
- local note
- general note
Drawn with4H pencil
Lettered with2H pencil.
engineering108.com
![Page 9: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/9.jpg)
indicate the location on the object’s features that are dimensioned.
EXTENSION LINES
engineering108.com
![Page 10: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/10.jpg)
RecommendedPractices
engineering108.com
![Page 11: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/11.jpg)
EXTENSION LINES
Leave a visible gap (≈ 1 mm) from a view and start drawing an extension line.
Extend the lines beyond the (last) dimension line 1-2 mm.
Visible gap
COMMON MISTAKE
engineering108.com
![Page 12: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/12.jpg)
Do not break the lines as they cross object lines.
COMMON MISTAKE
Continuous
EXTENSION LINES
engineering108.com
![Page 13: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/13.jpg)
Dimension lines should not be spaced too close
to each other and to the view.
11 34
Leave a space at least2 times of a letter height.
16
35
DIMENSION LINES
Leave a space at least1 time of a letter height.engineering108.com
![Page 14: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/14.jpg)
DIMENSION FIGURESThe height of figures is suggested to be 2.5~3 mm.
Place the numbers at about 1 mm above dimension
line and between extension lines.
COMMON MISTAKE
11
11
34
34
engineering108.com
![Page 15: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/15.jpg)
16.2516.25
or
DIMENSION FIGURES
When there is not enough space for figure or
arrows, put it outside either of the extension lines.
1
Not enough spacefor figures
Not enough spacefor arrows
1 1
engineering108.com
![Page 16: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/16.jpg)
The JIS and ISO standards adopt the unit of
Angular dimension in degree with a symbol “o”
place behind the figures (and if necessary
minutes and seconds may be used together).
DIMENSION FIGURES : UNITS
Length dimension in millimeters without
specifying a unit symbol “mm”.
engineering108.com
![Page 17: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/17.jpg)
1. Aligned method
2. Unidirectional method
The dimension figures are placed so that they are readable from the
bottom and right side of the drawing.
The dimension figures are placed so that they can be read from the
bottom of the drawing.
Do not use both system on the same drawing or on the same series of drawing (JIS Z8317)
DIMENSION FIGURES : ORIENTATION
engineering108.com
![Page 18: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/18.jpg)
30
30
30
30
30
3030
30
EXAMPLE : Dimension of length using aligned method.
engineering108.com
![Page 19: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/19.jpg)
30
30
30
30
3030
30
30
EXAMPLE : Dimension of length using unidirectional method.
engineering108.com
![Page 20: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/20.jpg)
45 o
45 o
45o
45o
45o
45o
45o
45o
EXAMPLE : Dimension of angle using aligned method.
engineering108.com
![Page 21: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/21.jpg)
45o
45o
45o
45o
45o45o
45o
45o
EXAMPLE : Dimension of angle using unidirectional method.
engineering108.com
![Page 22: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/22.jpg)
LOCAL NOTES
Place the notes near to the feature which they
apply, and should be placed outside the view.
Always read horizontally.
10 Drill
COMMON MISTAKES
10 Drill≈ 10mm
10
Dri
ll
Too far
engineering108.com
![Page 23: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/23.jpg)
DimensioningPractices
engineering108.com
![Page 24: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/24.jpg)
THE BASIC CONCEPT
Dimensioning is accomplished by adding size and location information
necessary to manufacture
the object.
Clear
Complete
Facilitate the- manufacturing method- measurement method
This information have to be
engineering108.com
![Page 25: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/25.jpg)
L
L
S
S
S
Designedpart
EXAMPLE
To manufacture this part we need to know…
1. Width, depth and thickness of the part.
2. Diameter and depth of the hole.
3. Location of the holes.“S” denotes size dimension.
“L” denotes location dimension.
S
L
L
engineering108.com
![Page 26: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/26.jpg)
ANGLE
engineering108.com
To dimension an angle use circular dimension
line having the center at the vertex of the angle.
COMMON MISTAKE
![Page 27: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/27.jpg)
FILLETS AND ROUNDSGive the radius of a typical fillet only by using alocal note.
R6.5
If all fillets and rounds are uniform in size,
dimension may be omitted, but it is necessary to
add the note “ All fillets and round are Rxx. ”
NOTE:All fillets and round are R6.5
Drawing sheet
R12
unless otherwise specified.NOTE:All fillets and round are R6.5
engineering108.com
![Page 28: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/28.jpg)
f xx
Use leader line and local note to specify diameter
and hole’s depth in the circular view.
HOLES : SMALL SIZE
xx Drill, Thru.
1) Through thickness hole
f xx Thru.
or
xx Drill.
or or
engineering108.com
![Page 29: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/29.jpg)
f xx, yy Deep
HOLES : SMALL SIZE
or
xx Drill, yy Deep
Hole’sdepth
Use leader line and local note to specify diameter
and hole’s depth in the circular view.
2) Blind hole
engineering108.com
![Page 30: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/30.jpg)
f xx
Use extension and dimension lines
Use diametral dimension line
Use leader line and note
HOLES : LARGE SIZE
engineering108.com
![Page 31: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/31.jpg)
COMMON MISTAKE
f xxf xx f xx
Rxx
f xx
HOLES
f xx
engineering108.com
![Page 32: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/32.jpg)
CHAMFERUse leader line and note to indicate linear
distance and angle of the chamfer.
S
qS q
For a 45o chamfer
S SCS
or
engineering108.com
![Page 33: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/33.jpg)
ROUNDED-END SHAPES
R12f 12
21
5
Dimensioned according to the manufacturing
method used.
Center to Center Distance
engineering108.com
![Page 34: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/34.jpg)
ROUNDED-END SHAPES
R12
21
5
12
Dimensioned according to the manufacturing
method used.
Center to Center Distance
engineering108.com
![Page 35: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/35.jpg)
ROUNDED-END SHAPESDimensioned according to the manufacturing
method used.
R12
21
12
16
engineering108.com
![Page 36: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/36.jpg)
ROUNDED-END SHAPES
R12
27
12
Dimensioned according to the manufacturing
method used.
Tool cutting distance
engineering108.com
![Page 37: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/37.jpg)
ROUNDED-END SHAPESDimensioned according to the standard sizes ofanother part to be assembled or manufacturing method used.
25
Key(standard part)
engineering108.com
![Page 38: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/38.jpg)
ROUNDED-END SHAPESDimensioned according to the standard sizes ofanother part to be assembled or manufacturing method used.
20
engineering108.com
![Page 39: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/39.jpg)
Placement ofDimensions
engineering108.com
![Page 40: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/40.jpg)
1. Extension lines, leader lines should not cross
dimension lines.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 41: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/41.jpg)
2. Extension lines should be drawn from the nearest
points to be dimensioned.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 42: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/42.jpg)
3. Extension lines of internal feature can cross visible
lines without leaving a gap at the intersection point.
WRONG CORRECT
RECOMMENDED PRACTICE
engineering108.com
![Page 43: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/43.jpg)
4. Do not use object line, center line, and dimension line as an extension lines.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 44: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/44.jpg)
POOR GOOD
5. Avoid dimensioning hidden lines.
RECOMMENDED PRACTICE
engineering108.com
![Page 45: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/45.jpg)
POOR GOOD
6. Place dimensions outside the view, unless
placing them inside improve the clarity.
RECOMMENDED PRACTICE
engineering108.com
![Page 46: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/46.jpg)
JUST OK !!! BETTER
RECOMMENDED PRACTICE 6. Place dimensions outside the view, unless
placing them inside improve the clarity.
engineering108.com
![Page 47: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/47.jpg)
7. Apply the dimension to the view that clearly show
the shape or features of an object.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 48: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/48.jpg)
8. Dimension lines should be lined up and grouped
together as much as possible.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 49: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/49.jpg)
9. Do not repeat a dimension.
POOR GOOD
RECOMMENDED PRACTICE
engineering108.com
![Page 50: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/50.jpg)
Vision to spread knowledge
• Send interesting contents about particular subjects , articles on global stuffs, engineering materials to us which will be helpful to your friends and others.
• We member of PROJECT FUNDA, provide a medium to make all this world wide through your great support. We request you to join this project and make tutorial of at least one chapter of your choice, that will help you to blow your name and your knowledge over the world.
engineering108.com
![Page 51: Dimensioning Engineering108.Com](https://reader035.vdocuments.us/reader035/viewer/2022070415/55cf96fc550346d0338f1488/html5/thumbnails/51.jpg)
Thank You
For more tutorials on engineering subjects visit us at engineering108.com
engineering108.com