Tape

Use 1” wide clear packing tape for hinges. Clean all parts withrubbing alcohol before taping

All airframe parts and control surfaces are cut from 6mm Deporn Foam

Dashed line repre-sents alternitive cut

line if 6mm side plate xBrace is used

Design by Mickey Crawley - Plans by Steven Gibson

® Copyright 2005 3Dbatix.com. All rights reserved.

Wing Span....... 37”Length............33.75”Weight............12-13ozPower............. AXI 2212/34 Prop.............. GWS 12x4Ch................ 4Battery.......... 3 Cell-700 to 1350mAh-Li-Poly

* Depron 6mm/3mm White (www.depronusa.com)* 30” 4mm & 2mm wrapped carbon fiber tube* .040 Solid Carbon Rod (push rods + stab support) or...optional 3mm flat carbon rod tab support * .080 Solid Carbon Rod (landing gear support) * Medium or Thick foam friendly CA* Foam friendly CA accelerator* JZ Products Super RC “Z’ 56 glue* 1” Self-sticking Hook & Loop (Velcro-Industrial Strength) tape* Clear packing tape* 4-E-flite Micro Control Horns No. EFLA200 OR...4 Du-Bro Micro Control Horns No. 848* 4 Du-Bro Micro E/Z Links No. 849* .032 wire control arms* 1/2” Nylon Filament Strapping (3M brand)* Zagi tape for trim scheme (optional)* Straight edge razor-blades* No. 11 Xacto knife* Metal yardstick* 3M Photomount Spray Adhesive (for plan transfer to Depron)

Rx and Servos* GWS R-4PH 4ch receiver or equivalent* 4 Waypoint W-084 Micro Servos or Hitec HS 55Brushless Motor* AXI 2212/34 outrunner (Max 3D performance)

Speed Controller* Phoenix 25amp speed controllerBattery* 3 Cell 700-1350mAh-11.1v Li-Poly BatteryProp(s) * GWS 12x6 Slow Flyer* APC 12x3.8 electric slow flyer

Lightly coat back of plan parts with Spray Adhesive, apply each part to Depron. Carefully cut each part outusing a straightedge and #11 Xacto.

Speed control, Rx and rudder/elevator servos. Note landing gear set-up

A Rotary Tool Cutting Adapter is perfect for clean easy to make grooves for Fiber Carbon rod stiffeners.

FLIGHT SYSTEM RECOMMENDATIONS MATERIALS LIST HINGE DETAIL PUSHROD DETAIL BUILD & FINISHING DETIALSDIABLO-3 D PARK FLYER SPECS

.030 -.040 solid carbon rod (or 3mm flat carbon rod) gluled to the trailing edge of the stab right in front of the hinge line for spanwise stiffness

Landing Gear

3mm Depron

Denotes cut-lines

AXI 2212/34 External Rotor Brushless

AXI Brushless Motor Shown

1/8” light plywood radial mount, reinforced with Depron triangle stockon all 4 sides

Rudder Servo

Aileron Servo

Cut side plate (xBrace)from 3mm Depron

6mm Depronoptional

Elevator Servo

Servo cutout

Servo cutout

.8mm carbon rod landing gear support/stiffener. Groove foam and glue with order-free (foam friendly) CA or JZ Products Super RC Z 56

Glue scrape Depron triangles for extra strength

Wing

NOTE: landing gear shown is not functional but is recommended for improved flight performance

3 Cell700-1350 mAh Li-Poly Battery

All parts are cut from 6mm Depron unless stated otherwise

0

1

2

3

4

123 0

Inch Scale reference, check after printing.

Diablo-3D Park Flyer

.032 wire control rods

.040 Solid Carbon Rod push rods

Heat shrink tubing

Colored Zagi tape works great for trim. It’s best to trim each part before assembly.

Not speed control and Rx locations. Battery is on the opposite side.

Thick CA works fine for mounting the light ply motor mount.

4mm carbon fiber tube. Cut a channel (per plan) on the bottom of the wing only and CA or RC-56 in place.

Wing cut from one piece of 6mm Depron foam

Aileron control hornsAileron cut line

CG

Initial CG 2 - 2.5” from leading edge root Reinforce carbon rod

landing gear crossing with 1/32 ply

Use on control servo arms. CA 3” of wire to 2mm carbon fiber rod, secure with 1” of heat shrinking tubing. Carbon rod fits opposite side of control arms, wire connects and holds rod in place