deviceinstaller€¦ · the upgrade wizard continues. when the boot code is installed, a...

DeviceInstaller

Installation Guide

Network Device Installation Software EN

DeviceInstaller | Installation Guide | Contents

2 Bosch Security Systems, Inc. | 4/10 | 4998138688-04

Contents 1.0 Introduction ............................................................... 3 2.0 DeviceInstaller Overview ..................................................... 3 2.1 Device Compatibility ......................................................... 3 2.2 Requirements .............................................................. 3 3.0 Install the Software ......................................................... 4 3.1 Install Microsoft .NET Framework 2.0 ............................................. 4 3.2 Install DeviceInstaller......................................................... 5 4.0 Upgrade Device Firmware .................................................... 6 4.1 Upgrading XPort-03/04 to v5.x.x.x Devices ......................................... 6 4.2 Upgrading Devices Other Than XPort-03/04 v5.x.x.x.................................. 8 5.0 Uninstall DeviceInstaller .................................................... 11

DeviceInstaller | Installation Guide | 1.0 Introduction

.

Bosch Security Systems, Inc. | 4/10| 4998138688-04 3

Trademarks Trademark names are used throughout this document. In most cases, these designations are claimed as trademarks or registered trademarks in one or more countries by their respective owners. Rather than placing a trademark symbol in every occurrence of a trademark name, Bosch Security Systems, Inc. uses the names only in an editorial fashion and to the benefit of the trademark owner with no intention of infringing the trademark.

• Microsoft, Windows 2000, XP, Server 2003, Vista, Windows 7, and .NET are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• InstallShield is a registered trademark and service mark of InstallShield Software Corporation in the United and/or other countries.

• Lantronix is a registered trademark of Lantronix Corporation, registered in the U.S. and other countries.

• CoBox , Device Server, and Xport are trademarks of Lantronix Corporation.

1.0 Introduction The C900V2, DX4020, D9133TTL-E, and the C900TTL-E are Network Interface Modules (NIMs) that either convert or intercept digital data into network data with the use of a network interface module by Lantronix Inc. The D6680, D6682, and D6100i Network Adapters are also devices produced by Lantronix Inc. As new features are added to these modules, the firmware might need updating. To update these modules, use the DeviceInstaller software.

Pay attention to which hardware revision you are attempting to upgrade. Each revision of hardware requires specific software.

If the wrong software is loaded, it causes an inoperable unit that must be sent back to Bosch Security Systems, Inc. for repair.

This application is used only to upgrade firmware files to the network interface modules.

All other functions of this application are not supported by Bosch Security Systems, Inc.

2.0 DeviceInstaller Overview 2.1 Device Compatibility This utility upgrades the following Conettix products:

• C900TTL-E Dialer Capture Module

• C900V2 Dialer Capture Ethernet Module

• D6100i Communications Receiver/Gateway

• D6680 Ethernet Network Adapter

• D6682 Ethernet Network Adapter

• D9133TTL-E Serial Interface Module

• DX4020 Network Interface Module

2.2 Requirements The following software is required to use the DeviceInstaller application:

• Supported operating systems:

- Microsoft Windows 2000 with Service Pack 2 or later

- Microsoft Windows Server 2003

- Microsoft Windows XP

- Microsoft Windows Vista

- Microsoft Windows 7

• Microsoft Internet Explorer 5 or later

• Microsoft .NET Framework 2.0

DeviceInstaller | Installation Guide | 3.0 Install the Software


3.0 Install the Software

Insert the D6200 CD-ROM into your CD-ROM drive. The D6200 CD-ROM directory should automatically open.

If the CD-ROM directory does not automatically open:

1. Select Start→Run...

2. At the prompt, type X: (“X” = the drive letter assigned to your CD-ROM drive).

3. Click OK. The CD-ROM directory opens.

Microsoft .NET Framework 2.0 is not required for the Windows Vista operating systems.

If you are using the Windows Vista operating system, or if Microsoft .NET Framework 2.0 is already installed, go to Section 3.2 Install DeviceInstaller, page 5.

3.1 Install Microsoft .NET Framework 2.0

1. From the CD-ROM directory, select Network Interface Modules and Software→Device Installer.

2. Double-click the dotnetfx.exe file. After the installation files are extracted, the .NET Framework 2.0 Setup Welcome window opens.

Figure 1: .NET Setup Welcome Window

3. Click Next.

The End-User License Agreement window opens.

Figure 2: .NET End-User License Window

4. Select I accept the terms of the License Agreement, then click Next. The .NET Installing Components window shows the installation progress.

Figure 3: .NET Installing Components Window

DeviceInstaller | Installation Guide | 3.0 Install the Software

.


5. When the Setup Complete window opens, click Finish.

Figure 4: .NET Setup Complete Window

.NET Framework 2.0 is successfully installed.

3.2 Install DeviceInstaller 1. From the CD-ROM directory, select Network

Interface Modules and Software→Device Installer.

2. Double-click the Di32DL_x.x.x.x_Web.exe file. The Location to Save Files window opens.

Figure 5: Location to Save Files Window

3. Click Next to save the installation files in the default location. The Setup Wizard Welcome window opens.

Figure 6: Setup Wizard Welcome Window

4. Click Next. The Select Installation Folder window opens.

Figure 7: Select Installation Folder Window

DeviceInstaller | Installation Guide | 4.0 Upgrade Device Firmware


5. Click Next to install DeviceInstaller in the default folder. The Confirm Installation window opens.

Figure 8: Confirm Installation Window

6. Click Next. When the installation is completed, the Installation Complete window opens.

Figure 9: Installation Complete Window

7. Click Close to exit from the Setup Wizard. DeviceInstaller is successfully installed.

4.0 Upgrade Device Firmware 4.1 Upgrading XPort-03/04 to v5.x.x.x

Devices 1. To start the DeviceInstaller application, select

Start→All Programs→ Lantronix→ DeviceInstaller 4.2→DeviceInstaller. When startup is complete, the DeviceInstaller application queries the network for all installed Lantronix devices.

2. Select the device to upgrade from either the tree pane on the left side of the application (expand the node and select the device with the IP address), or the device pane on the right side. The Upgrade button appears in the toolbar when a device is selected.

Figure 10: DeviceInstaller User Interface

1- Tree pane 2- Device pane 3- Upgrade button

3. Click the Upgrade button. The Upgrade Wizard starts.

Figure 11: Select LXI File

4. Click Use a specific installation file (LXI), then click Browse. The Select Installation File window opens.


.


Figure 12: Select Installation File

5. Navigate to the D6200 CD-ROM, then to Network Interface Modules Software→Firmware Installation Files (LXI).

6. Select the DX4020-C900V2_v5.x.x.x-to-v6-Boot_(XPort-03).lxi file. Click Open. The Upgrade Wizard continues. When the boot code is installed, a confirmation message appears.

Figure 13: Boot Code Installation Success

At this point in the upgrade procedure, the device is not yet upgraded from v5.x.x.x firmware to v6.x.x.x. Only the boot code is loaded.

On the XPort-03/04 device, check the status LEDs on the XPort. Both LEDs should be flashing simultaneously to indicate that the upgrade is in progress, but the device is not ready for normal operation. Refer to Figure 14 for the location of the XPort LEDs.

Figure 14: XPort LEDs (DX4020 example)

1 2

1- Link LED 2- Activity LED

7. An error message appears on the DeviceInstaller user interface. Click OK to continue.

8. On the DeviceInstaller user interface, click the Search button to refresh both panes. At first, the device shows as an XPort-03/04 v2 device in the tree pane until the search function is completed. The device then updates to an XPort-03/04 v6 device.








12. Select the DX4020-C900V2_v6.x.x.x-to-v6.1.8.3_(XPort-03).lxi file.

13. Click Open. The Upgrade Wizard continues.

14. Click Next to install the files. The update starts. A confirmation message appears indicating whether or not the update was successful. If the update attempt fails, the wrong installation file was selected for the device.

Figure 17: Upgrade Success

4.2 Upgrading Devices Other Than XPort-03/04 v5.x.x.x

1. To start the DeviceInstaller application, select Start→All Programs→ Lantronix→ DeviceInstaller 4.2→DeviceInstaller. When startup is complete, the DeviceInstaller application queries the network for all installed Lantronix devices.

2. Select the device to upgrade from either the tree pane on the left side of the application (expand the node and select the device with the IP address), or the device pane on the right side. The Upgrade button appears in the toolbar when a device is selected.

Figure 18: DeviceInstaller User Interface

1- Tree pane 2- Device pane 3- Upgrade button





.



7. Click Next to install the files. The update starts. A confirmation message appears indicating whether or not the update was successful. If the update attempt fails, the wrong installation file was selected for the device.

Figure 21: Upgrade Success


6. Select the appropriate LXI file for the device. Refer to Table 1 and Table 2 on page 10. Click Open. The Upgrade Wizard continues.



Table 1: Proper Software Version to Use Based on Hardware Revision

UDS Family XPort Family Device Hardware Revision 1

(CBXM-ERAD) Hardware Revision 2 (CM-E2-RAD)

XPort-01 XPort-03/04

D9133TTL-E cbx5884.rom D9133-C900TTL_(CBXM-ERAD).lxi

ltx5884.rom D9133-C900TTL_(CM-E2-RAD).lxi

N/A N/A

C900TTL-E cbx5884.rom D9133-C900TTL_(CBXM-ERAD).lxi

ltx5884.rom D9133-C900TTL_(CM-E2-RAD).lxi

N/A N/A

Xpt03_6183.rom DX4020-C900V2_v6.x.x.x-to-v6.1.8.3_(XPort-03).lxi

DX4020 N/A N/A xpt_5883.rom DX4020-C900V2_(XPort-01).lxi

C900V2 N/A N/A xpt_5883.rom DX4020-C900V2_(XPort-01).lxi

Xpt03_6183.rom DX4020-C900V2_v6.x.x.x-to-v6.1.8.3_(XPort-03).lxi

D6100i N/A N/A N/A Xpt03_6183.rom

Table 2: Proper Software Version to Use Based on CoBox Hardware Revision

UDS Family Device CoBox Hardware Revision 1

(COBOX-EXT-ENET) CoBox Hardware Revision 2 (COBOX-FL-01)

D6682 Ethernet Network Adapter (UDS2100)

D6680 cbx5884.rom D6680_(Cobox-E2).lxi

ltx5884.rom D6680_(Cobox-FL-01).lxi

N/A

D6682 N/A N/A D6682_(UDS2100).lxi

You can identify which XPort module you have by looking at the last two digits of the module’s label.

For example, on an XPort-01 label:

You can identify the Conettix product’s hardware version by looking at the label on the side of the product:

DeviceInstaller | Installation Guide | 5.0 Uninstall DeviceInstaller

.


4. To remove the program, click the Change or Remove Programs button. A confirmation window appears prompting you to confirm the program’s removal.

5.0 Uninstall DeviceInstaller 1. Select Start→Settings→Control Panel.

The Control Panel window opens.

Figure 24: Add or Remove Confirmation Figure 22: Control Panel Window

5. Click Yes to continue. A window appears showing an animation of files flying from a folder and disappearing. A task bar is at the bottom showing the progress of the removal. When the Remove process is completed, a new window appears stating that all components were successfully removed.

6. Click the Finish button to close this window.

2. Click Add or Remove Programs. The Add or Remove Programs utility starts.

3. Scroll to Lantronix DeviceInstaller x.x.x.x, and click once to select it.

Figure 23: Add/Remove Programs

© Bosch Security Systems, Inc. 2010 4998138688-04

Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 USA www.boschsecurity.com

deviceinstaller€¦ · the upgrade wizard continues. when the boot code is installed, a...

Documents