detech specs

2
Practical values of melt correction factor for use in calculation of shot weight for some common plastics Shot weight = melt correction factor x swept volume in cc The melt correction factor takes into account the change in volume at process temperature and also includes a factor for the flow characteristics of the shut off device on the end of the screw HD-PE 0.75 LD-PE 0.73 PP 0.73 PS 0.91 SB 0.91 ABS 0.91 SAN 0.91 PA 0.93 PA 6 + 30% GF 1.14 PC 0.97 POM 1.15 PET 1.08 PBT 1.08 CA 1.03 CAB 0.98 PVC - s 1.05 PVC - r 1.15 Thermoset - PF 0.96 PC / ABS alloy 0.94 PMMA 0.97 Material Melt Correction Factor PPM/2007/08/rev .01 Bangalore Chandigarh Chennai Coimbatore 38, Cubbon Road, P.O. Box 5098, Bangalore 560 001 Tel : 080-25020100/0236, Fax : 080-25536397 e-mail : [email protected] 32, Sector 26-D, Madhya Marg, P.O.Box 14, Chandigarh -160 019. Tel : 0172-4646846, Fax : 0172-4646802 e-mail : [email protected] 10, Club House Road, Anna Salai, Chennai 600 002 Tel : 044-28462034, Fax : 044-28462088/2152 e-mail : [email protected] 123, Appuswamy Road, Coimbatore 641 045 Tel : 0422-2311562, Fax : 0422-2313881 e-mail : [email protected] SALES & CUSTOMER SUPPORT CENTRES : Hyderabad Kolkata Mumbai New Delhi 2nd & 3rd Floor, SUMMIT, 5-10-188/2,Hill Fort Road, Hyderabad 500 004 Tel : 040-66720000, Fax : 040-23242356 e-mail : [email protected] 3B, Shakespeare Sarani, Kolkata 700 071 Tel : 033-22825138, Fax : 033-22827587 / 22821025 e-mail : [email protected] EPC Block, 5th Floor, ‘A’ Wing, Gate No.1, Powai West, Mumbai 400 072 Tel : 022-67053580/3688/1147 Fax : 022-67051309 e-mail : [email protected] 32, Sivaji Marg, P.O. Box 6223, New Delhi 110 015 Tel : 011-41419585/87, Fax : 011-41419518/9600 e-mail : [email protected] Pune Vapi Vadodra 191/1, Dhole Patil Road, P.O. Box 119, Pune 411 001 Tel : 020-26113557, 56033355 Fax : 020-26113557 e-mail : [email protected] 19/23, Mohid Towers, Vapi-Daman Road, Chala, Vapi 396 195 Cell : 93273 74710 e-mail : [email protected] Radhadaya Complex, Near Charotar Society Old Padra Road, Vadodara 390 015 Tel : 0265-2343238, Fax : 0265 2336184 e-mail : [email protected] L&T - Demag Plastics Machinery Limited Chembarambakkam Off - Chennai - Bangalore Highway P.O. Box No. 5 Chennai - 602 103 Phone : +91-44-26812000, Fax : +91-44-26810303 E-mail: [email protected] MANUFACTURED BY HEAD OFFICE Plastics Processing Machinery, LTM Business Unit Mount Poonamallee Road Manapakkam, Chennai 600 089. India. Tel: +91-44-22491932 / 22497360 Fax: +91-44-22492471 E-mail: [email protected] [email protected] LARSEN & TOUBRO LIMITED All manifold blocks & valves mounted close to the actuators for faster response Oil tank with large opening for cleaning Pre heating circuit for hydraulic oil Oil temperature regulated with temperature indication Connectors for external oil filtration during production (bye pass filtration) Automatic monitoring of oil filter clogging with advance warning and read out Pump unit switched off if minimum oil level is reached or if the oil filter is100% blocked Production stopped if oil temperature exceeds maximum value High pressure filter with clogging indication External oil cooler Digital principle of control for speed and pressure for consistent and reliable performance Fast responding and non-aging catridge logic elements Fast responding hydraulic door safety interlock Energy saving pump switch off feature in case of idle running Intelligent operator terminal with large multi colour LCD display and alpha numeric key board (10.5") Easy setting of parameters through graphics using mouse wheel 3.5” disc drive for loading Ergocontrol and PLC software and also for storing machine setting data CAN bus as field bus linking the Ergocontrol and machine controllers Position measuring system for moving platen, ejector, and screw travel Setpoint input on the Ergocontrol in physical values (bar, cc, mm/sec, screw rpm) or speeds for mould, ejector, core puller and nozzle as a percentage of maximum value Graphics supported input of set point profiles for injection speed, follow up pressure, back pressure and screw speed as an alternative to entry of numerical values 2 screens free for entry of general data (set up information) Continuous Process control via monitoring of important process parameters with selectable tolerance band Moulding counter preselection with automatic switch off feature Shift and batch production counters with rejection monitoring Fault diagnostics in the event of machine malfunction or operator error with plain text messages and recording of source of error Automatic switch off mould cooling in the event of fault in the cycle Printer interface (centronics) through parallel port PDS Process data acquisition PDE with statistics and graphics Measurement of cycle, injection, plasticising and mould protection times Regulated power supply 24V DC for controls and actuators Set of electrical outlet- Single Æ (1x 10 A) & 3 Æ (1x16 A) Socket for printer Multi level password for preventing tampering of parameters Smart card reader for preventing unauthorised access Flash lamp /Acoustics alarm Hot runner controlled integrated (upto 16 zones) Flexible motion sequences for cores and ejectors Digital setting of all times,setting range in seconds Function wise layout of pages(screens) and ergonomical display of various process parameters/data in clear text Heater current display device (upto IU 900 only) PID control loops and semiconductor relays for cylinder heating system Self Optimising PID control loops and semiconductor relays for cylinder heating system Main voltage 415V/3ph/50Hz, control voltage 24VDC/220V Internal storage of upto 60 mould set programmers Injection speed settable in mm/sec and pressure settable in bar Injecton speed settable in 63 steps and pressure settable in 127 steps PC connectivity for additional storage of mould catalogue Switch on programme for oil preheating and cylinder heating Controls Energy indication on operator panel SPC and CPk with graphical display Machine troubleshooting module indicating clear direction to resolve problems Hot runner shut off device (pneumatic/hydraulic) Remote access of control pages Down time log Strat up module for automatic selection of process parameters (Ergostart) Insulated heater bands Auto switch off programme - purging w/o hopper shutoff Language options Programmable automatic switch-off matrix Networking of machines Guarded machine enclosure with space for protruding moulds and peripheral connections One piece machine bed (upto 350) Safety equipment as per EN 201 Flexible machine support with anti vibration mounts Total preventive maintenence Three way access for easy part removal Complete cover on the Injection unit front side Mould clamps - 8 numbers Separate oil filter for fine straining (Bypass filtration); integrated in the machine Three color lamp (only in LNC) Single phase preventor Connection for additional heater band - only plug will be with the machine 32 pole signal interface in accordance with VDMA for robots/sprue picker (E12) Euromap 67 interface Rotating core interface Mould protection by monitoring ejector back sensing using limit switch (1 no.) in mould Interface for ejector limit switch(2 nos) in the mould Sensor interface for monitoring drop of mountings with photocell option Freely programmable I/O's (Max.2 I/O-LNC5,6 I/O -Ergo) 3 Stage start up programme Automatic printer programme Thermal printer Interface for indexing conveyor/floating contact Blending unit interface Chiller/peripheral fault interface Amendment report log Interface with gas assisted moulding Interface for quick mould change Interface for cavity pressure sensor - upto 2 channels Interface for add. nozzle heater band (plug only) Interface for slide core safety control Interface upto 4 temperature control units, 3 point controller - Outputs for heating and cooling CAN interface for temperature control device - upto 2 circuits Interface mould temperature display on IBED; upto 2 - mould circuits Thermal printer integrated in Ergocontrol TPM program Help Menu Process data storage (on floppy in ergocontrol/download in excel format in LNC) Flexible motion sequence - CU-IU (core and ejector movement, IU) Insert loading sequence Process trouble shooting (Ergoexpert) Injection compression sequence Breathing sequence General Functions/Interfaces - Standard - Option NA - Not Available NEC - No extra cost, ALT - Alternative Equipment 40 - 650

Upload: kunwar-ahmad

Post on 27-May-2015

144 views

Category:

Technology


9 download

DESCRIPTION

mohd ahmad qamar

TRANSCRIPT

Page 1: Detech specs

Practical values of melt correction factor for use incalculation of shot weight for some commonplastics

Shot weight = melt correction factor x swept volume in cc

The melt correction factor takes into account the change involume at process temperature and also includes a factor forthe flow characteristics of the shut off device on the end of thescrew

HD-PE 0.75

LD-PE 0.73

PP 0.73

PS 0.91

SB 0.91

ABS 0.91

SAN 0.91

PA 0.93

PA 6 + 30% GF 1.14

PC 0.97

POM 1.15

PET 1.08

PBT 1.08

CA 1.03

CAB 0.98

PVC - s 1.05

PVC - r 1.15

Thermoset - PF 0.96

PC / ABS alloy 0.94

PMMA 0.97

Material Melt Correction Factor

PP

M/2

00

7/0

8/r

ev.0

1

Bangalore

Chandigarh

Chennai

Coimbatore

38, Cubbon Road, P.O. Box 5098,Bangalore 560 001Tel : 080-25020100/0236, Fax : 080-25536397e-mail : [email protected]

32, Sector 26-D, Madhya Marg,P.O.Box 14, Chandigarh -160 019.Tel : 0172-4646846, Fax : 0172-4646802e-mail : [email protected]

10, Club House Road, Anna Salai,Chennai 600 002Tel : 044-28462034, Fax : 044-28462088/2152e-mail : [email protected]

123, Appuswamy Road,Coimbatore 641 045Tel : 0422-2311562, Fax : 0422-2313881e-mail : [email protected]

SALES & CUSTOMER SUPPORT CENTRES :

Hyderabad

Kolkata

Mumbai

New Delhi

2nd & 3rd Floor, SUMMIT,5-10-188/2,Hill Fort Road, Hyderabad 500 004Tel : 040-66720000, Fax : 040-23242356e-mail : [email protected]

3B, Shakespeare Sarani,Kolkata 700 071Tel : 033-22825138,Fax : 033-22827587 / 22821025e-mail : [email protected]

EPC Block, 5th Floor, ‘A’ Wing,Gate No.1, Powai West, Mumbai 400 072Tel : 022-67053580/3688/1147Fax : 022-67051309e-mail : [email protected]

32, Sivaji Marg, P.O. Box 6223,New Delhi 110 015Tel : 011-41419585/87, Fax : 011-41419518/9600e-mail : [email protected]

Pune

Vapi

Vadodra

191/1, Dhole Patil Road,P.O. Box 119, Pune 411 001Tel : 020-26113557, 56033355 Fax : 020-26113557e-mail : [email protected]

19/23, Mohid Towers, Vapi-Daman Road,Chala, Vapi 396 195Cell : 93273 74710e-mail : [email protected]

Radhadaya Complex, Near Charotar SocietyOld Padra Road, Vadodara 390 015Tel : 0265-2343238, Fax : 0265 2336184e-mail : [email protected]

L&T - Demag Plastics Machinery LimitedChembarambakkamOff - Chennai - Bangalore HighwayP.O. Box No. 5Chennai - 602 103Phone : +91-44-26812000, Fax : +91-44-26810303E-mail: [email protected]

MANUFACTURED BY HEAD OFFICE

Plastics Processing Machinery, LTM Business Unit

Mount Poonamallee RoadManapakkam, Chennai 600 089. India.

Tel: +91-44-22491932 / 22497360Fax: +91-44-22492471

E-mail: [email protected]@ltmindia.com

LARSEN & TOUBRO LIMITED

All manifold blocks & valves mounted close to the actuators forfaster responseOil tank with large opening for cleaningPre heating circuit for hydraulic oilOil temperature regulated with temperature indicationConnectors for external oil filtration during production (bye passfiltration)Automatic monitoring of oil filter clogging with advance warning andread outPump unit switched off if minimum oil level is reached or if the oilfilter is100% blockedProduction stopped if oil temperature exceeds maximum valueHigh pressure filter with clogging indicationExternal oil coolerDigital principle of control for speed and pressure for consistent andreliable performanceFast responding and non-aging catridge logic elementsFast responding hydraulic door safety interlockEnergy saving pump switch off feature in case of idle running

Intelligent operator terminal with large multi colour LCD displayand alpha numeric key board (10.5")Easy setting of parameters through graphics using mouse wheel3.5” disc drive for loading Ergocontrol and PLC software and also forstoring machine setting dataCAN bus as field bus linking the Ergocontrol and machinecontrollersPosition measuring system for moving platen, ejector, and screwtravelSetpoint input on the Ergocontrol in physical values (bar, cc,mm/sec, screw rpm) or speeds for mould, ejector, core puller andnozzle as a percentage of maximum valueGraphics supported input of set point profiles for injection speed,follow up pressure, back pressure and screw speed as an alternativeto entry of numerical values2 screens free for entry of general data (set up information)Continuous Process control via monitoring of important processparameters with selectable tolerance bandMoulding counter preselection with automatic switch off featureShift and batch production counters with rejection monitoringFault diagnostics in the event of machine malfunction or operatorerror with plain text messages and recording of source of errorAutomatic switch off mould cooling in the event of fault in the cyclePrinter interface (centronics) through parallel portPDS Process data acquisition PDE with statistics and graphics

Measurement of cycle, injection, plasticising and mould protectiontimesRegulated power supply 24V DC for controls and actuatorsSet of electrical outlet- Single Æ (1x 10 A) & 3 Æ (1x16 A)Socket for printerMulti level password for preventing tampering of parametersSmart card reader for preventing unauthorised accessFlash lamp /Acoustics alarmHot runner controlled integrated (upto 16 zones)Flexible motion sequences for cores and ejectorsDigital setting of all times,setting range in secondsFunction wise layout of pages(screens) and ergonomical display ofvarious process parameters/data in clear textHeater current display device (upto IU 900 only)PID control loops and semiconductor relays for cylinder heatingsystemSelf Optimising PID control loops and semiconductor relays forcylinder heating systemMain voltage 415V/3ph/50Hz, control voltage 24VDC/220VInternal storage of upto 60 mould set programmersInjection speed settable in mm/sec and pressure settable in barInjecton speed settable in 63 steps and pressure settable in 127stepsPC connectivity for additional storage of mould catalogueSwitch on programme for oil preheating and cylinder heating

Controls

Energy indication on operator panelSPC and CPk with graphical displayMachine troubleshooting module indicating clear direction toresolve problemsHot runner shut off device (pneumatic/hydraulic)Remote access of control pagesDown time logStrat up module for automatic selection of process parameters(Ergostart)Insulated heater bandsAuto switch off programme - purging w/o hopper shutoffLanguage optionsProgrammable automatic switch-off matrixNetworking of machines

Guarded machine enclosure with space for protruding moulds andperipheral connectionsOne piece machine bed (upto 350)Safety equipment as per EN 201Flexible machine support with anti vibration mountsTotal preventive maintenenceThree way access for easy part removalComplete cover on the Injection unit front sideMould clamps - 8 numbersSeparate oil filter for fine straining (Bypass filtration); integrated inthe machineThree color lamp (only in LNC)

Single phase preventorConnection for additional heater band - only plug will be with themachine32 pole signal interface in accordance with VDMA for robots/spruepicker (E12)Euromap 67 interfaceRotating core interfaceMould protection by monitoring ejector back sensing using limitswitch (1 no.) in mouldInterface for ejector limit switch(2 nos) in the mouldSensor interface for monitoring drop of mountings with photocelloptionFreely programmable I/O's (Max.2 I/O-LNC5,6 I/O -Ergo)3 Stage start up programmeAutomatic printer programmeThermal printerInterface for indexing conveyor/floating contactBlending unit interfaceChiller/peripheral fault interfaceAmendment report logInterface with gas assisted mouldingInterface for quick mould changeInterface for cavity pressure sensor - upto 2 channelsInterface for add. nozzle heater band (plug only)Interface for slide core safety controlInterface upto 4 temperature control units, 3 point controller -Outputs for heating and coolingCAN interface for temperature control device - upto 2 circuitsInterface mould temperature display on IBED; upto 2 - mouldcircuitsThermal printer integrated in ErgocontrolTPM programHelp MenuProcess data storage (on floppy in ergocontrol/download in excelformat in LNC)Flexible motion sequence - CU-IU (core and ejector movement, IU)Insert loading sequenceProcess trouble shooting (Ergoexpert)Injection compression sequenceBreathing sequence

General

Functions/Interfaces

√ ●- Standard - OptionNA - Not Available NEC - No extra cost, ALT - Alternative Equipment

40 - 650

Page 2: Detech specs

FEATURESLNC5 ERGOClamping unit

Injection Unit

Computer optimised 5-point twin toggle system, for fast, smoothplaten movement and even distribution of clamp forceMoving platen supported on the machine bed by anti-friction rollerbearingsMould opening and ejector forward with safety guard open /closedpositionMould mounting dimensions as per Euromap - Threaded holesupto 300T and T-slot from 350T (with ejector holes on Movingplaten for Euromap/JIS)Add-on T-slot plates upto 150T,Integral T slot 180 T to 300TMould Mounting dimensions as per DIN/SPI standardsDrill hole pattern for robot/sprue pickerRear safety guard suitable for robot/sprue pickerHard chrome plated tie barsToggle bearings oil/grease lubricated: lubrication signalscomputer optimised under adaptive controlMotorised mould height adjustment through sun & planetary gearmechanismConsistent mould open stop position using stroke adjustmentmechanism in cylinder set manuallyConsistent mould open stop position using mould openproportional valveClosed loop clamp force control on control panel with indicationand correction every cycle, settableClosing and opening speeds independently set: eachprogrammable in 3 stagesRegenerative circuit in mould closing for higher speedsLow pressure mould safety, settableMould protection with stroke dependent change over with timemonitoring and repeat of a clamping cycle aborted in the protectedrangeCentral hydraulic ejector with multiple stroke features and fastcoupling; pressure and speed independently set in both directions,ejector speed programmable in 2 stagesMould cooling water switch off in case of interruption of cycle, withsettable timerWater battery - 4 fold upto 250T; 6 fold above 250THydraulic ejector parallel to mould movement with speed andpressure manually adjustableShort and long stroke ejector, freely programmableMulti point ejector plate as per EuromapMultipoint ejector plate as per JISWater battery - 6 / 8 / 12 fold1,2,3 or 4 pneumatic valves (5/2 type)freely programmableCore pulling control for 1,2,3 or 4 hydraulic/pneumatic coresindependently programmable for sequential operation or parelleloperationHydraulic ejector/core parellel to mould opening with independentcontrol of speed and pressure through proportional valve; ejectorand core with serial movement to each otherGood/bad parts selector,via continous process controlAutomatic mould height adjustment through proximity switch(upto 350T)Automatic mould height adjustment through Linear potFoolproof hydraulical and electrical interlocks for safety gatesStainless Steel Discharge chute upto 250 TElevated base for clean roomAdditional 4/6/8/10/12 water manifold with Original Italy makeballvalve control with Stainless steel SS304 .Pneumatic operated safety door

Central Ejector rod (as per m/c manual )Connections for 2 core pull controls at fixed platenNonreturn valve of ejector (for moulds with spring loaded ejectors)Multipoint Ejector Rods (M12 Internal threads on one end)

Injection unit with torque-free nozzle contact with 2 cylinde

Injection unit speed of nozzle advance and retractionprogrammable in 2 stagesNozzle contact pressure programmable

Injection speed, follow up pressure and screw speed controlled byfast response DFE pumpDirect screw drive by hydraulic motor 1 for high speedsHydraulic motor II high torqueScrew cylinder fitted with universal thermoplastics nitrided screwand nitrided cylinder: non-return valve and cylinder closureassembly with SVO open nozzleScrew cylinder suitable for upto 3 injection units: L/D ratio 20:1 forall diametersFast cylinder change with central connectors for heating systemand thermocouples and with automatic cylinder identification(from 430IU)Ceramic cylinder heating bandsPID controlled barrel heater bands5 self-optimising temperature control circuits for the cylinder andnozzle heating system with adjustable tolerance monitoring ofdeviation from set point and thermocouple break resistance;operating range of up to 400°C4/5 temperature circuits for cylinder heating with monitoringofdeviation and thermocouple statusTemperature of the screw cylinder feed zone adjustableInjection speed profile programmable in * position dependentinterpolation stagesFollow up pressure profile programmable in * time dependentinterpolation stagesFollow up pressure switching activated as a function of position,time or hydraulic pressureScrew speed and back pressure control, profile programmable in *position dependent interpolation stepsScrew speed input in *Injection speed input in *Monitoring of melt cushion during the follow up pressure phaseHydraulic screw retraction after follow up pressure phase and orafter plasticising process programmable dependent on position, toprevent melt droolingDelay feature for commencement of plasticising and nozzleretractionScrew rotation lock engaged until cylinder reaches set temperatureReduction in cylinder temperatures to a preset value duringmachine idle timeNozzle guard with electrical interlock for operator safetyIntrusion and cold slug removalStainless steel hopperExtended nozzle with heater bandHydraulically operated shut off nozzle (SVH)Electrical screw drive for parellel plasticizing (from IU 840 - 10500)Sprue bush temperature controlSpecial Barrier screws for better homogenization and plasticisingrates from screw dia 30Wear resistant through hardened screw and bimetallic barrel forabrasive materialsProven screw Geometry for high plasticising capacities withexcellent melt homogeneityThermoset package and sequences dia 30 to 50CPVC/RPVC/PET package25 L/D screw (for A and B)Hard chrome plated screwMelt filter nozzle from screw dia 30Dosing delay timerCold start protection for screwNozzle contact force setting through control panel with residualnozzle contact forceFast injection with accumulator, programmable (from 150Tonwards)Melt temperature measuring (SVO)Injection closed loop with servo valve

Pump unit 1 with energy saving SYDFEE regulated pumpVariable displacement pump for energy conservationLow noise drive with quiet pumps sound insulating enclosures forhydraulicsPressures and flow rates, closed loop, controlled by fastresponding DFE regulated pump

Hydraulics

mm/scc/s

rpmmm/s

L

B

H

kN

kN

mm

mm

mm

mm

mm

kg

kg

mm

kN

L

kg

mm

mm

mm

lpm

2300-553900E-55/75*7000-75/90*

1400 2000

2000

5000

Injection Moulding Machine (Detech SERIES)

Clamping Unit

1400

5000

2100 2400

9735 for IU230010590 for IU3900E

2300 2400

9735 for IU 230010590 for IU3900E11210 for IU7000

8290

2400

3900E-55/75*7000-75/90*

10500-90/110*

* Optional pump / injection unit+Optional opening stroke

##7200 for IU 600&9007940 for IU 1400 &2350

5600

1800

5600

1800

650/1000

300

139/57

1880

1450x1350

1000x900

8600

6500

7150

810 980

5700

930

450/950380/820 380/900

760/1300***

31200/33200/35100

2480

120

10630 for IU3900E11225 for IU7000

11965 for IU10500

2475

6050

1880

550/870

5500

40/320 60/320 85/420 100/420 200/580

400 600 850 1000 2000

440 660 935 1100

575310 310 380 380

1630

180/410 180/410 200/530 200/530

1365

340/790

720

1265x1265

870x870

860x860

810x810

1200x1200

580x580

7000

630x630

420 420 700 700

4500

2250 51003500

100 120 120

34002300

230180 200

180 180 285 285 ##400/580

90/45

760

69/31 70/39

580

3200 3200 4300 4300

40 60 60

80-11120-11200-11310-11

120 120

2400

120

20900/21900/24300

90/45

760/1300**

600

330/770

1370

940x940

40

2300-553900E-55/75*

** For IU7000

2400

9735 for IU 230010590 for IU3900E11210 for IU7000

800/980+

380/900

1265x1265

5500

1700/1880+

500/870

5000

870x870

7000

4500

230

120

2400

20900/21900/24300

90/45

760/1300**

2300-553900E-55/75*7000-75/90*

900-30/37*1400-30/37/45*

2350-37/45*

600 -30/37*900-30/37*

1400-30/37/45*2350-37/45*

200-15310-15/22*

430-22*

80 -11120-11

310-15/22*430-22600-22

2160

##10000/11000

*** For IU7000/10500

Total Mould carrying capacity

Max.mould.wt.in moving platen

Hydraulic Ejector stroke

Ejection Force/Retraction Force

Oil Tank Capacity

Max.Daylight between Platens

Overall Size of Platens

Distance between Tiebars

Clamping Force

Locking Force

Mould Opening Stroke

Mould Height(Min/Max)

Net Weight (Without oil)

Dimensions of machines

Cooling water requirement

Injection Unit applicable & Pump unit (kW)

## -200/580 With 600/900 IU

2000

120

2000

20900/2190013200/14200

45/2545/2528/13

2000

28/13

230

1500450450280280

100

720

420x420420x420320x320320x320

480x480 480x480 600x600 600x600

910910

125/510

1250

200/550

720x720

510x510

1100

160

45/25

310-22430-22600-22900-22

6500

6650

1600

60

2000

310

700

1375

450

1000

150/510

1500

200/550

720x720

510x510

1100

160

45/25

310-22430-22

600-22/30*900-22/30*

6500

6650

60

2000

1600

310

700

1650

450

1000

4500

450/810

49502200

325/630

3250

3575

B C A B C A B C A B C A B C D A B C A B C

50 60 50 60 70 60 70 80 60 70 80 70 80 90 95 80 95 110 95 110 130

20 20 20 20 20 20 20 20 20 20 20 23 20 20 20 24 20 20 23 20 20

2022 1404 2565 1780 1300 2420 1877 1437 2557 1878 1438 2423 1855 1516 1316 2391 2094 1562 2434 2006 1436

442 636 530 820 1116 891 1212 1584 919 1251 1634 1636 2137 2704 3013 2388 3367 4515 3899 5227 7300

402 579 482 746 1016 811 1103 1441 836 1138 1487 1489 1944 2461 2742 2173 3064 4108 3548 4756 6643

159/223/313 228/322/450 176/246/301 253/355/433 345/483/590 373 508 663 230/281 313 /383 409/500 393/447 513/584 650/739 724/823 406/490 572/691 767/926 538/634 721/851 1007/1188

37/52/- 56/-/- 26/36/45 40/58/70 58/82/99 60 87 122 56/69 81/99 114/139 59/65 83/91 101/110 133/146 62/78 100/125 144/181 80/98 116/141 164/200

22/31/43 33/46/65 - - - 41 59 83 33/40 48/58 67/82 48/52 67/74 81/90 108/119 41/51 66/82 95/119 54/66 78/95 110/135

- - - - - - - - - - - - - - - - - - - -

270 290 290

14.8 23.1 14.8 23.1 27 23.1 27 30.6 23.1 27 30.6 31 31 43 43 43 43 59 59 59 79

110

315

55 90/110

110

45

75/90

550

45

110

45

475325 425

70

45

68 70

37/45 55/75

110

20 45

Specifications are subject to change due to continuous improvements

30/37/4522/30/37

225

45

A

45

20

2496

358

325

128/181/253

24.5/35/-

14.5/20/28.5

-

11.3

A B C A B C A B C A B C A B C A B C

mm 18 22 25 22 25 30 25 30 35 30 35 40 35 40 45 40 45 50

20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

bar 2778 1860 1440 2591 2006 1393 2740 1900 1400 2755 2024 1550 2644 2025 1600 2448 1934 1567

cc 23 42 54 42 61 88 61 106 144 106 168 220 168 231 293 231 323 399

g 21 38 49 38 56 80 56 96 131 96 153 200 153 210 266 210 294 363

cc/s 73 109 141 78 101 146 71/71 102/102 139/139 74/74/116 100/100/158 131/131/207 121 158 200 132/186/261 167/236/330 207/291/408

g/s 4.5 7.5 14 7.5 13 19 12/12 16/16 22/22 13/13/21 18/18/28 25/25/39 21.5 31 44 25.5/30/- 36/-/- 48/-/-

g/s 4 6.5 12 5.5 10 14 9.5/9.5 13.5/13.5 18/18 10.5/10.5/16.5 14/14/22 20/20/31 18 25.5 36 20/23/28 28/32/39 38/44/52

g/s - - - - - - - - - - - - - - - 15/20/22 22/26/31 30/42/47.5

mm 90 110 110 110 125 125 125 150 150 150 175 175 175 184 184 184 203 203

mm

kN

kW 5 5.1 5.7 5.1 5.7 8.3 5.7 8.3 9.4 8.3 9.4 11.1 9.4 11.1 11.3 11.1 11.3 14.8

kW

Injection Moulding Machine (Detech SERIES)

Theoretical value, actual value depends on material grade, melt density

45 45

68 68 68 68

20 20

68

1400 23502300 105003900E 7000900430 60080 120 200 310Injection Unit Size

Plasticising flow in PS#

Max.Nozzle dipping depth(SVO)

Nozzle Contact force

Heating Capacity

Pump unit

Shot weight in Polystrene(PS)

Rate of Injection in PS#

Screw Stroke

Stage I

Stage II

Stage III

Screw Cylinder

Screw Diameter

L/D Ratio

Injection Pressure

Cylinder Head Volume

#Achieved in air injection

22/30/372211 11 11/15* 11/15/22

68

4545