DEPUY SYNTHES CONTINUOUS COMPRESSION IMPLANTSDesigned to provide continuous, active compression throughout the healing processApproved by the AOTK

Ease of Use

Enhanced Implant Design

• Pre-sterilized disposable system includes instrumentation to

enhance operating room efficiencies

• Implants are pre-loaded to save time and hassle in the OR and facilitate

easy, precise placement of the implantInsertion Tool

Depth Gauge

Drilling Templates

SPEED™ Implant

SPEEDTITAN™ Implant

BME ELITE® Implant

Extra wide bridge

Retains compression after repetitive loading

Barbed legs provide secure fixation

High strength, stiffness and rotational stability for high-load applications

The BME ELITE® Continuous Compression Implants (CCIs) were compared to the following constructs: locking titanium

midfoot compression plates, with and without 4.0mm lag screws, and crossing 4.0mm screws. These fixation combinations

are commonly used in various arthrodesis sites. Compression measurements were taken using Tekscan® pressure maps

placed between bicortical Sawbone® blocks. Measurements were taken before and after repetitive loading of 100 cycles

at 2mm displacement.

Constructs using the BME ELITE Implants provided significantly more compression than a locking titanium midfoot

compression plate with and without a 4.0mm lag screw and crossing 4.0mm lag screws.

Continuous Active Compression

Compression Comparison (N)

0

20

40

60

80

100

120

140

160

180

BME ELITE Implant

TR-110-03-16188

SPEEDTITAN Implant

TR-110-03-16188

SPEED Implant

TR-03-120-1430

Two BME ELITE Implants @ 90˚

Plate with Screw

Crossing Screws

P

RE-C

YC

LIN

G

PO

ST-C

YC

LIN

G

TEST SETUP LAPIDUS PROCEDURE TEST RESULTS*

Compression Heat Map Test #: TR-132-03-15131

*Bench Test results may not necessarily be indicative of clinical performance

SPEED CONTINUOUS COMPRESSION IMPLANT

IMPLANT KIT BRIDGE* LEGS* Wire Size*

Drill Kit*

SE-0907 09 07 1.5x1.5 DK-200

SE-0910 09 10 1.5x1.5 DK-200

SE-1110 11 10 1.5x1.5 DK-200

SE-111513 11 15/13 1.5x1.5 DK-200

SE-1310 13 10 1.5x1.5 DK-200

SE-131513 13 15/13 1.5x1.5 DK-200

SE-1512 15 12 1.5x1.5 DK-200

SE-1515 15 15 2x2 DK-265

SE-1815 18 15 2x2 DK-265

SE-1818 18 18/15 2x2 DK-265

SE-1818 18 18 2x2 DK-265

SE-2015 20 15 2x2 DK-265

SE-2020 20 20 2x2 DK-265

SE-2520 25 20 2x2 DK-265

CORRESPONDING DRILL KIT

PARTNUMBER

DRILLBIT SIZE

DRILL GUIDE

HANDLE

LOCATORPINS

TAMP

DK-200 2.00mm Included Included Included

DK-265 2.65mm Included Included Included

ANCILLARY TOOLSPARTNUMBER

DRILL BIT SIZE

SG-1 Continuous Compression Implant Sizing Guide

SPEEDTITAN CONTINUOUS COMPRESSION IMPLANT IMPLANT KIT BRIDGE A* LEGS B*

SE-1515TI 15 15

SE-1815TI 18 15

SE-181815TI 18 18/15

SE-1818TI 18 18

SE-2015TI 20 15

SE-2020TI 20 20

SE-2520TI 25 20

CORRESPONDING DRILL KIT

PARTNUMBER

DRILLBIT SIZE

DRILL GUIDE

HANDLE

LOCATORPINS

TAMP

DK-265-S 2.65mm Included Included Included

ANCILLARY TOOLSPARTNUMBER

DRILLBIT SIZE

SG-1 Continuous Compression Implant Sizing Guide

BME ELITE CONTINUOUS COMPRESSION IMPLANT

IMPLANT KIT BRIDGE* LEGS*NO. of LEGS

MAX. CLOSURE*

EL-1515S2 15 15 2 9.1

EL-1818S2 18 18 2 10.4

EL-2020S2 20 20 2 9.5

EL-2520S4 25 20 4 7.1

EL-3020S4 30 20 4 7.6

CORRESPONDING DRILL/TEMPLATE KITS

PART NUMBER

DRILL BIT SIZE

DRILLING TEMPLATES

LOCATOR PINS

TAMP K-WIRES

DK-300 3.0mm – 4xLP-300 EL-TAMP 0.062 in.

EL-DTS –15, 18, 20,

25, 30– – –

Wide BridgeLow Profile

Narrow Legs

2-Leg Configuration

5.51.5

2.5

Wide BridgeLow Profile

Narrow Legs

4-Leg Configuration

5.5

1.5

2.5

ALL SIZES IN MILLIMETERS

EL-1515S2 EL-1818S2 EL-2020S2 EL-2520S4 EL-3020S4

1.85* Low Profile

Wide Bridge3.5*

1.8*

Wide Bridge

*Sizes in millimeters

*Sizes in millimeters

*Sizes in millimeters

Standard Size Implant

ideal for a variety of procedures in the forefoot

Akin Osteotomies

Designed with a sloped-bridge that conforms to the sloping surfaces of the metaphyseal anatomy

Chevron Osteotomies

Three-legged design provides stable fixation and allows for medial or dorsal placement

Calcaneal Slide Osteotomies

Offset design with a range of offset lengths

Perform incision and bone resections and address soft

tissue contractures as necessary

Large Size Implant

A wider, low-profile bridge for higher strength and compression required for midfoot applications

Extra-large Size Implant

High strength, stiffness, and rotational stability for high-load applications in the midfoot and hindfoot

steotomies

ge

SPEE

DTI

TAN

IMPL

AN

T

SPEED IMPLANT SPEEDARC IMPLANT

SPEEDTRIA

D IM

PLAN

T

BME ELITE IM

PLANT

HAMMERLOCK® 2 IMPLANT

SPEEDSH

IFT

IMPL

AN

T

L

Afr

Various StrengthsDePuy Synthes offers one of the most comprehensive

range of CCIs with proper sizes and strengths for

forefoot, midfoot and hindfoot procedures.

Standard Size Implant

ideal for a variety of procedures in the forefoot

Akin Osteotomies

Designed with a sloped-bridge that conforms to the sloping surfaces of the metaphyseal anatomy

Chevron Osteotomies

Three-legged design provides stable fixation and allows for medial or dorsal placement

Calcaneal Slide Osteotomies

Offset design with a range of offset lengths

Perform incision and bone resections and address soft

tissue contractures as necessary

Large Size Implant

A wider, low-profile bridge for higher strength and compression required for midfoot applications

Extra-large Size Implant

High strength, stiffness, and rotational stability for high-load applications in the midfoot and hindfoot

steotomies

ge

SPEE

DTI

TAN

IMPL

AN

T

SPEED IMPLANT SPEEDARC IMPLANT

SPEEDTRIA

D IM

PLAN

T

BME ELITE IM

PLANT

HAMMERLOCK® 2 IMPLANT

SPEEDSH

IFT

IMPL

AN

T

L

Afr

Procedure Specific Shapes

DePuy Synthes is also the first company to offer

a range of CCIs designed in distinctive shapes

to support a variety of specialized elective

foot procedures.

ANCILLARY TOOLSPART NUMBER NAME

HSPL01 HAMMERSPLINT™

CORRESPONDING DRILL KITPART NUMBER DRILL BIT SIZE

DK-H2 2.10mm

SPEEDARC™ CONTINUOUS COMPRESSION IMPLANT

IMPLANT KIT BRIDGE* LEGS* WIRESIZE*

SE-091210A 9 12/10 1.3x1.5

SE-111210A 11 12/10 1.3x1.5

SE-111512A 11 15/12 1.3x1.5

CORRESPONDING DRILL KIT

PARTNUMBER

DRILLBIT SIZE

DRILL GUIDE

HANDLE

LOCATORPINS

TAMP

DK-200 2.00mm Included Included Included

ANCILLARY TOOLSPARTNUMBER

DESCRIPTION

SG-3 SPEEDARC™ Implant Sizing Guide

SPEEDTRIAD™ CONTINUOUS COMPRESSION IMPLANT

IMPLANT KIT BRIDGE* LEGS* BRIDGEWIDTH* DISTAL LEGS

SE-181508TRC 18 15 8 CENTERED

SE-181508TRL 18 15 8 LEFT OFFSET

SE-181508TRR 18 15 8 RIGHT OFFSET

SE-201508TRC 20 15 8 CENTERED

SE-201508TRL 20 15 8 LEFT OFFSET

SE-201508TRR 20 15 8 RIGHT OFFSET

CORRESPONDING DRILL KIT

PARTNUMBER

DRILLBIT SIZE

DRILL GUIDE

HANDLE

LOCATORPINS

TAMP

DK-200T 2.0mm Included Included Included

ANCILLARY TOOLSPART NUMBER DESCRIPTION

SG-2 SPEEDTRIAD™ Sizing Guide

SPEEDSHIFT™ CONTINUOUS COMPRESSION IMPLANT

IMPLANT KIT BRIDGE* LEGS* OFFSET* WIRESIZE*

SE-1520-06 15 20 6 2x2

SE-1520-08 15 20 8 2x2

SE-1520-10 15 20 10 2x2

SE-2020-04 20 20 4 2x2

SE-2020-06 20 20 6 2x2

SE-2020-08 20 20 8 2x2

SE-2020-10 20 20 10 2x2

SE-2020-12 20 20 12 2x2

CORRESPONDING DRILL KIT

PARTNUMBER

DRILLBIT SIZE

DRILL GUIDE

HANDLE

LOCATORPINS

TAMP

DK-265-S 2.65mm Included Included Included

ANCILLARY TOOLSPART NUMBER DESCRIPTION

SG-1 Continuous Compression Implant Sizing Guide

OT-1 Offset Sizing Tool

HAMMERLOCK® 2 CONTINUOUS COMPRESSION IMPLANT

ANGLE SIZE CAT. NO A* B* C* D* E* F*

0° SMALL HL2S 17.2 5.2 12.0 5.6 5.4 4.3

0° MEDIUM HL2M 20.2 5.2 15.0 6.0 5.4 5.0

0° LARGE HL2L 22.0 7.0 15.0 6.0 7.0 5.0

10° SMALL HL2SA 17.2 5.2 12.0 5.6 5.4 4.3

10° MEDIUM HL2MA 20.2 5.2 15.0 6.0 5.4 5.0

10° LARGE HL2LA 22.0 7.0 15.0 6.0 7.0 5.0

Shape when activated

* All sizes in millimeters describing implants in activated states. X-ray Template A125-005 may be used to determine implant size.

*Sizes in millimeters

*Sizes in millimeters

*Sizes in millimeters

RIGHT OFFSET CENTER OFFSET LEFT OFFSET

© DePuy Sythes 2018. All rights reserved.

Third party trademarks used herein are the trademarks of their respective owners DSUS/TRM/0417/1426(2) 3/18

Manufactured or Distributed by:

Synthes USA, LLC1101 Synthes AvenueMonument, CO 80132

Note: For recognized manufacturer, refer to the product label

www.depuysynthes.com

Limited Warranty and Disclaimer: DePuy Synthes Products are sold with a limited warranty to the original purchaser against defects in workmanship and materials. Any other express or implied warranties, includingwarranties of merchantability or fitness, are hereby disclaimed. Please also refer to the package insert(s) or other labeling associated with the devices identified in this sales document for additional information.

CAUTION: Federal Law restricts these devices to sale by or on the order of a physician. Some devices listed in this sales aid may not have been licensed in accordance with Canadian law and may not be for sale in Canada.

Please contact your sales consultant for items approved for sale in Canada.

Not all Products may currently be available in all markets.

BioMedical Enterprises, Inc.14785 Omicron Dr., Suite 205San Antonio, TX 78245

SPEED, SPEEDARC, SPEEDTITAN, SPEEDSHIFT, BME ELITE Continuous Compression Implants Indications: • Fracture and osteotomy fixation and joint arthrodesis of hand and foot. • Fixation of proximal tibial metaphysis osteotomy. • Fixation of small bone fragments (i.e. small fragments of bone which are not comminuted to the extent to preclude staple placement). These fragments may be located

in long bones such as femur, fibula and tibia in the lower extremities; the humerus, ulna or radius in the upper extremities; the clavicle; and in flat bone such as pelvis, scapula.

Contraindications:• Comminuted bone surface that would militate against staple placement. • Pathologic conditions of bone such as osteopenia that would impair the ability to securely fix the implant. • Foreign body sensitivity to metals including nickel. Where material sensitivity is suspected, appropriate test should be made prior to implantation.

SPEEDTRIAD Continuous Compression Implants Indications:• Fracture and osteotomy fixation and joint arthrodesis of hand and foot.

Contraindications:• Comminuted bone surface that would militate against staple placement. • Pathologic conditions of bone such as osteopenia that would impair the ability to securely fix the implant. • Foreign body sensitivity to metals including nickel. Where material sensitivity is suspected, appropriate test should be made prior to implantation.  

HAMMERLOCK 2 Continuous Compression Implants Indications:Small bone reconstruction and fusion such as in the phalanges of the fingers and toes Contraindications:• Pathologic conditions of bone such as osteopenia that would impair the ability to securely fix the implant.• Foreign body sensitivity to metals including nickel. Where material sensitivity is suspected, appropriate test should be made prior to implantation.

Anatomic ReductionFracture reduction and fixation to restore anatomical relationships.

Stable FixationFracture fixation providing absolute or relative stability, as required by the patient, the injury, and the personality of the fracture.

Early, Active Mobilization Early and safe mobilization and rehabilitation of

the injured part and the patient as a whole.

Preservation of Blood Supply Preservation of the blood supply to soft tissues and bone by gentle reduction techniques and careful handling.

AO PrinciplesIn 1958, the AO formulated four basic principles, which have become the guidelines for internal fixation.1,2

1Müller ME, M Allgöwer, R Schneider, H Willenegger. Manual of Internal Fixation. 3rd ed. Berlin Heidelberg New York: Springer. 1991.2Rüedi TP, RE Buckley, CG Moran. AO Principles of Fracture Management. 2nd ed. Stuttgart, New York: Thieme. 2007.