Dependable Solutions for Gas Detection

Combustibles/FlammablesStandard & Exotic ToxicsOxygen Enrichment/Deficiency

Introduction to Sensidyne

Established in 1983 - acquired by Schauenburg GmbH in April 2008– A multinational company with 37

locations worldwide– Sensidyne is the instrumentation hub

for the Americas

Expanded to new manufacturing and corporate headquarters in January, 2013

Certified to ISO9001:2008

Ongoing investment in product development and sustaining engineering

Sensidyne Fixed Gas Detection

Committed to providing the best solutions for gas detection.

Robust designs that are hazardous area and performance certified

Gas detection options certified to SIL2 for hardware and software

Predictive maintenance functions

Universal instrument platforms

Uncompromising dedication to the highest level of quality.

Quality Management System structured & operated in accordance with ISO 9001:2008– Plant Is An ISO 9001:2008, EN

13485:2003 Certified Facility

Employees share responsibility to provide products with superior quality

Customer satisfaction is our highest priority

Providing Solutions to a Wide Range of Industries and Applications

SensAlert ASIAdvanced Safety Integrity for confidence in every safety application.

Enhanced design to ensure reliability– Third-party SIL-2 certification

validating reliability– Sensors are performance tested

and certified– Sensor Test-On-Demand, with

on-board gas generator– Predictive sensor failure

Universal platform with Intrinsically Safe sensor head– Replace sensors without area

declassification or hot work permits– Shop calibrate then hot-swap gas sensors

in hazardous classified areas– Remote mount sensor up to 100 ft./30 m.

away without rigid conduit– RS485 Modbus RTU & HART

communication options and Standard 4-20 mA

Intelligent Plus Series sensors– Auto-recognition and set-up from sensor memory – Extensive sensor options for

Flammables/Combustibles, Toxics, and Oxygen– Compatible with all Plus Series sensor ranges and

technologies– Four records of calibration– Min/Max gas and temperature readings

Flexible installation or retrofit– 2-wire and 3-wire transmitter models with

global performance approvals– Versatile installation and operation in

hazardous classified areas– Non-intrusive configuration and

maintenance interface– Configurable alarms & warnings for hazard notification

Wide-ranging application options– Intrinsically Safe or Explosion Proof

installation configurations– Remote sensors and gassing, duct mount, and

sample draw

SensAlert ASIUnmatched application versatility and ease of use.

Intrinsic Safety– NEC and CEC Class I Div 1, Grps A, B, C, D;

Class II Grps E, F, G; Class III T4ATEX EEx ia IIC T4 II 1 G

CE Mark– ATEX Directive 94/9/EC

IECEx– IEC 60079-0:2006, IEC 60079-11:1999, IEC

60079-15:2007

SIL-2 Certified– IEC 61508 SIL-2 Parts 1,2, & 3 Hardware &

Software. Certified for use in SIL-2 applications.

Explosion Proof – NEC and CEC Class I Div 1, Grps A, B, C, D;

Class II Grps E, F, G; Class III T4

Flame Proof– ATEX EEx d[ia] IIC T4 II 2 [1] G

Non-Incendive– NEC and CEC Class I Div 2,

Groups A, B, C, D; Class II Grps E, F, G; Class III T4ATEX EEx nC [ia] IIC T4 II 3 [1] G

SensAlert ASIGlobal approvals – FM, CSA, ATEX, and CE

Certificate of Compliance – SIL-2

Compliance Certification for Parts 1 – 3 for

General, Electrical, and Software

SensAlert PlusUniversal platform gas detection transmitter for safety applications.

Foundation for development of SensAlert ASI

Shares all features of SensAlert ASI except:

ⓧ SIL2 Certification

ⓧ Four calibration records

ⓧ Menu driven contrast adjustment

ⓧ Rotatable enclosure options

ⓧ Calibration due notification

SensAlarm PlusAdvanced all-in-one gas monitoring system for local and remote gas detection.

Complete gas detection system– Stand-alone single point AC or DC

powered gas detection system– 1 or 2 double-flash strobes,

horn and reset button– Optional battery back-up

Application-flexible installation and easy maintenance– Non-intrusive configuration and

maintenance interface– Remote sensor & gassing,

duct mount, or sample draw– Mount sensor up to 100 ft./30 m.

away using 4 conductor cable

Shown in Dual Strobe Configuration

SensAlarm PlusConvenience and performance in a single easy to use and install package.

Intelligent Plus Series sensors for Combustible and Toxic gases Oxygen enrichment & deficiency– Percent remaining sensor life– Sensor auto-recognition and configuration– Uploads application parameters and

gas & alarm data– Time-stamped event and calibration data

Exceptional capability– Meets the demands of a many industrial

and heavy commercial applications– Supports Plus Series sensor

transportable calibration– Ideal for manufacturing, laboratories,

control rooms, and gas storage rooms

Shown in Single Strobe Configuration

SensAir CMB

Cost effective, heavy duty combustible gas detector with enhanced poison resistance.

High performance catalytic bead sensor– Enhanced poison resistance to Sulfides

and Silicon for continued monitoring in contaminated environments

– Long life sensor for reduced ownership costs

Factory Mutual approved– Division 1 & Division 2 approval – ATEX Zone 1 & Zone 2 approval

Explosion-proof 316 stainless steel sensor housing– High resistance to corrosion– Horizontal or vertical orientation options– Non-intrusive interface with display with

magnetic switches

Easy installation and maintenance– Designed for flexible

installation in new facilities or retrofit

– 3-wire, 4 – 20 mA output

Bright RED three digit LED display– High-visibility indication of

gas concentration– Blind transmitter available– Six LEDs corresponding to

magnetic switches and alarms

SensAir CMBUltimate solution for OEM and high-volume applications.

SensAlert Alarm AnnunciatorsAdded visual and audible annunciation for warning workers and supervisors.

Local alarm annunciation– Warning of gas hazard alarms to

nearby workers and supervisors

– Communicates warning to follow alarm procedures or not to enter

Single and dual strobe options

Available power supply to power transmitters

Annunciation models available general purpose (shown left) or hazardous area approved

FM listed for NFPA 820 compliance– Approved for remote sampling in

Class 1 Division 2 areas from Class 1 Division 1 areas

– Flexible solution to overcome challenging gas detection applications

– Decreases personnel time hazardous areas

Pumped or air aspirated versions– Flow sensor with fail-safe relay – Internal power switch and flow adjustment– External flow indication and LED’s

24 VDC power source for gas detectors– Power up to four transmitters– Allows for stand-alone system with the

addition of annunciation

Sample Draw SystemApproved solution for monitoring gas in remote or difficult to access applications.

SensAlert 4-Channel ControllerFour channel controller with smart features for SensAlert family transmitters.

Ultimate companion for SensAlert family gas detectors– Automatic sensor recognition and

configuration for most Plus Sensors– Easy push-button interface for

custom setup– 24 VDC power source for up to

four gas detectors

Application-flexible– NEMA 4X fiberglass wall-mount

enclosure– Single, dual, or non- strobe options– Three alarm relays per channel– Common fault relay

Model 9000 Dual & QuadTwo or four channel control panel for display and management of inputs.

Easy management of two or four channels of gas detection– Internal relays for annunciation

or startup of hazard mitigation sequence

– Graphic backlit LCD display– Accepts two or four 4-20 mA

inputs

Rich in features and capability– RS-485 Modbus RTU output– CSA approved for

Class 1 Division 2– Discrete alarm relays

Model 7100 Eight or Sixteen ChannelAdvanced control panel for display and management of inputs.

Accepts eight or sixteen gas detector inputs– Monitors 8 or 16, 4-20 mA inputs– Scaleable for future expansion – Wall-mount enclosure or

rack-mount configuration

Exceptional display & alarm logic– Common alarms with

acknowledge function– Discrete alarms with voting, grouping, – full configuration and 24 hour trending– Optional discrete 4-20 mA outputs– Dual (Master and Slave)

RS-485 Modbus RTU outputs

Factory Commissioning & ServiceEnsure safety through expert start-up, repair, calibration, and maintenance.

Start-up and Commissioning– On site start-up of equipment, functional

testing, initial calibration, and training of local personnel

Contracted on-site calibration or maintenance– Routine calibration and maintenance services

by expert technicians

Sensor Calibration and Exchange Program– Scheduled delivery of factory calibrated

sensors– Customer’s second set of sensors stored at

factory until next calibration interval– Sensors tested in Sensidyne’s Factory Mutual

(FM) approved lab– Sensors ship with calibration certificate

Remote Sensor Mounting– Extension kits are provided to mount

sensors high, low or in difficult locations up to 100ft (30m)

Remote Calibration Adapters– Used with remote sensors for routine

calibration or bump testing from the transmitter location

ToD™ Gas Generator– The unique ToD cell manually or

automatically bump tests the sensor at user set intervals with a configurable result notification

Rainshield– Prevents wind blown water from

contacting the sensor and adversely affecting performance

Duct Mount Fixture– Provides general duct, vent hood, or air

intake monitoring for gases

Flow Through Cell (Flowblock)– Used in sampling systems to present

sample to the gas sensor

Moisture/Particulate Barrier– Snap in membrane protects sensor from

dust, particles, and reduces moisture transients

Aspirated Sample Draw– Uses an air aspirator to draw a sample

from a confined space, ceiling or other difficult to access location

Pumped Sample Draw– Same as above but employs a motorized

pump to draw a sample

Accessories and CalibrationTools to solve difficult gas detection applications and maintain calibration.

Sensidyne Fixed Gas DetectionThe most dependable solutions for gas detection.