denture catalog - swiss nf metalsswissnf.com/wp-content/uploads/2018/12/denturist... · 2 female...

©2018 Zest Anchors, LLC. All rights reserved. LOCATOR F-Tx, LOCATOR, LOCATOR R-Tx, Zest and Zest Dental Solutions are registered trademarks of ZEST IP Holdings, LLC.

No matter which road you and your patients take, there is only one destination – Zest Dental Solutions – the pioneer and leader in full-arch implant solutions since 1977.

Visit WWW.ZESTDENT.COM or call 800-262-2310.

FIXED Prosthesis - Clinician Removable

LOCATOR F-Tx®

Patient REMOVABLE Prosthesis

LOCATOR R-Tx®

LOCATOR F-Tx® - Novel FIXED full-arch Attachment System based on a PEEK snap-fit connection. NO SCREWS. NO CEMENT. NO COMPROMISES.

LOCATOR R-Tx® - Fourth generation patient REMOVABLE overdenture Attachment System predicated on the award-winning and market-leading LOCATOR® design. BETTER. SIMPLER. STRONGER.

TWO PATHS.ONE DESTINATION.

FULL-ARCH IMPLANT SOLUTIONS AHEAD

DENTURE CATALOG

SEPTEMBER 2018

IMPLANTS • ATTACHMENTS • TECHNICAL SUPPORT

*All prices are subject to change without notice2

• Implant divergence possible up to 60°• Functional and easy application• Tension-free seating of the prosthesis• Modular overall system• Hygienic solution without a central retention hole• High-quality, clinically proven materials• Precise, permanent retention• Compact design for a high level of wearing comfort • Attractive price/performance ratio• Swiss made

10 Years!

*All prices are subject to change without notice 3

CM LOC® Implant Abutments

IMPLANT DESCRIPTIONHEIGHT OF ABUTMENT TISSUE CUFF ABOVE THE IMPLANT

1.0mm 2mm 3mm 4mm 5mm Case Guide

Straumann®

Straumann® Tissue Level NNC 3.5 05001418 05001419 05001420 05001421 05001422 05001580

Straumann® Tissue Level RN 4.8 05001408 05001409 05001410 05001411 05001412 05001578

Straumann® Bone Level NC 3.3 05002547 05002548 05002549 05002550 05002551 05001580

Straumann® Bone Level RC 4.1/4.8 05001413 05001414 05001415 0500146 05001417 05001579

Nobel Biocare

Nobel Biocare Replace Select® NP 3.5 05001423 05001424 05001425 05001426 05001427 05001581

Nobel Biocare Replace Select® RP 4.3 05001296 05001300 05001301 05001302 05001303 05001582

Nobel Biocare Active® NP 3.5 05002109 05002110 05002111 05002112 05002113 05002187

Nobel Biocare Active® RP 4.3/5.0 05001437 05001438 05001439 05001440 05001441 05001584

Nobel Biocare Brånemark® RP 4.0 05002114 05002115 05002116 05002117 05002118 05002188

Dentsply - Astra Tech

Astra Tech OsseoSpeed® EV 3.6 05001963 05001964 05001965 05001966 05001967 05001981



Astra Tech OsseoSpeed® 3.5/4.0 05001452 05001453 05001454 05001455 05001456 05001587

Astra Tech OsseoSpeed® 4.5/5.0 05001457 05001458 05001459 05001460 05001461 05001588

Ankylos® C 3.5, 4.5, 5.5, 7.0 05002014 05002015 05002016 05002017 05002018 05002020

Hiossen®

Hiossen® TS Mini 3.5 05002154 05002155 05002156 05002157 05002158 05002196

Hiossen® SS Regular 4.8 05002149 05002150 05002151 05002152 05002153 05002195

BioHorizons® / Zimmer / MIS®

BioHorizons 3.5 Internal Hex 05001462 05001463 05001464 05001465 05001466 05001589

BioHorizosn 4.5 Internal Hex 05001467 05001468 05001469 05001470 05001471 05001590


Portfolio.

Order No. Material / Sets Content

see web T CM LOC® Abutment 1 pc.

see web T CM LOC® FLEX Abutment incl. Aligner

1 pc.

0500 1304 T CM LOC® CAD/CAM Retention elementRetention element for Bar

1 pc.

see web T CM LOC® Case Guide 1 pc.

see web T CM LOC® FLEX Case Guide 1 pc.

0500 1605 C CM LOC® Male part Ccasting-on / soldering technique

1 pc.

0500 1606 E CM LOC® Male part Elaser welding technique

1 pc.

0500 1325 PS CM LOC® Basic Set Pekkton® 2x female part housing Pekkton® 2x retention insert, extra-low 2x retention insert, low 2x retention insert, medium 2x Block-out Spacer 2x processing insert

0500 3001 TPS CM LOC® Basic Set Titanium 2x female part housing Titanium 2x retention insert, extra-low 2x retention insert, low 2x retention insert, medium 2x Block-out Spacer 2x processing insert

0500 1307 TES CM LOC® Basic Set Elitor® 2x female part housing made of titanium2x retention insert Elitor®, mounted 2x Block-out Spacer

0500 1306 P CM LOC® Housing Pekkton®

for Pekkton® inserts4 pcs.

0500 1995 T CM LOC® Housing Titaniumfor Pekkton® inserts

4 pc.

NEW

0500 1314 P CM LOC® Retention insert, extra-low 4 pcs.

0500 1315 P CM LOC® Retention insert, low 4 pcs.

NEW

See Page 3 for a Full Implant Compatibility List

Coming Soon!

$135See P.3

see web

see web

see web

05001304

05001605

05001606

05001325

05003001

05001307

05001306

05001995

05001314

05001315

NUMBER PRICEPRODUCT NAME

$87

$88

$78

$110

$90

$142

$68

$68

$55

$55

CM L

OC®

Impl

ant A

butm

ents


11

Order No. Material / Sets Content

0500 1316 P CM LOC® Retention insert, medium 4 pcs.

0500 1317 P CM LOC® Retention insert, strong 4 pcs.

0500 1318 TE CM LOC® Housing Titanium with Elitor® insert 1 pc.

0500 1328 P CM LOC® Processing insert 4 pcs.

0700 0201 P CM LOC® Spacer 4 pcs.

0700 0202 S CM LOC® Block-out Spacer 4 pcs.

0700 0204 T CM LOC® Analog 4 pcs.

0700 0205 T CM LOC® Multi-Toolfor Pekkton® Retention insert

1 pc.

0700 0206 X CM LOC® Screw Driver 1 pc.

0700 0222 X CM LOC® FLEX Screw Driver 1 pc.

0700 0211 T CM LOC® Activatorfor Elitor® Retention insert

1 pc.

0700 0213 P CM LOC® Impression part 4 pcs.

0700 0217 X CM LOC® Housing Extractor 1 pc.

0700 0219 T CM LOC® Parallelometer insert 1 pc.

0700 0200 CM LOC® Instrument Set with 3 instruments

0700 0223 POM CM LOC® FLEX Aligner 1 pc.

05001316

05001317

05001318

05001328

07000201

07000202

07000204

07000205

07000206

07000222

07000211

07000213

07000217

07000219

07000200

07000223

NUMBER PRICEPRODUCT NAME

$55

$55

$135

$55

$75

$22

$75

$95

$75

$75

$80

$75

$75

$58

$308

$37

CM LO

C® Implant A

butments


88

8

8

What’s New with HADER Bars...

The Combo Kit

everything needed for one bar caseIncludes: 1 Plastic Bar Pattern 2 Female Riders 2 Metal Housings (either style)2 Processing Spacers1 Female Insertion Tool

Hader Bar Servicing Kit

Ideal for relines, rebases, repairs, or fabricating a new overdenture on existing bars or CAD-CAM barsIncludes:1 Delrin Analog Bar2 Female Riders2 Metal Housings (either style)2 Processing Spacers1 Female Insertion Tool 4 Tubes Perma Block

Metal Clips available in gold and stainless steel

GREAT SAVINGS ON BULK PACKAGES OF 50! Female Riders • Metal housings • Processing spacers • Bar patterns (short or standard)

Incorrect - Female clipcannot flex over the bar

Bar Patterns

Available in Standard and Short heights

Aluminum Analog Bar

Delrin Analog Bar

Two different analog bars for relines, repairs, and making new prostheses

Plastic-wax is ideal for fast set investment

The processing spacer willprevent the over extention ofacrylic which inhibits flexationof the female rider

Processing Spacer

Hader Bar Mandrel

to assure parallelism between multiple bar segments

Kits

Processing model with green processing spacers & thin metal housings

4 retentions of female riders• Yellow-standard • White-decreased• Red-increased• Blue-for worn bars

New Alignment Housings Traditional Housings

Female Riders

Ackermann gold and stainless and C118 gold and stainless

Easy and accurate alignment of riders and housings with space saving options.

OVERDENTURE BARS


PRODUCT NAMENUMBER PRICE

13

13


13

13

Attachments

OVERDENTURE BARS

Universal size Titanium Locking Plunger for Overdenture Bars. May be rigid or resilient. 7.5mm long, may be cut to 6, 5, or 4mm. 1.5mm Ø plunger Plunger Diameter compatible with Swiss-Loc & Lew Passive

Universal Plunger Loc Attachment1776000 68.00

Universal Plunger Loc Processing Jig1776005 21.00

Universal Plunger Loc Male Only1776010 30.00

Universal Plunger Loc Twist Drill1776015 12.00

Rigid or Resilient Direct Retainer Precision Bar Overdenture Attachment System. Large U bar=2.2mm Ø ; Small Pear bar = 1.6mm Ø

Preci-Bar Standard Rigid Gold Male 50mm0101112 390.00

Preci-Bar Standard Rigid Pallax Male 50mm0101113 195.00

Preci-Bar Standard (Rigid) Plastic Bar (4-Pack)0101161 56.00

Preci-Bar Standard (Resilient) Plastic Bar (4-Pack)0101165 56.00

Preci-Bar Standard Gold Female 50mm0101106 310.00

Preci-Bar Standard Pallax Female 50mm0101109 160.00

Preci-Bar Mandrel Standard0101110 60.00

Preci-Bar Mini Resil. Gold Male 50mm0101104 270.00

Preci-Bar Mini Resil. Pallax Male 50mm0101105 135.00

Preci-Bar Mini (Resilient) Plastic Bar (4-Pack)0101163 56.00

Preci-Bar Mini Gold Female 50mm0101107 225.00

Preci-Bar Mini Pallax Female 50mm0101111 140.00

Preci-Bar Mandrel Mini010110 60.00

Universal Plunger Loc Attachm

entPreci-Bar (Dolder)

Plunger Loc

Plunger Loc

Dolder Bar

0101106

0101109

0101165

1776000

Plunger Loc10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS

Hader Plastic Bar Pattern (Short) (6-Pack)0101709-6 54.00


Hader Paralleling Mandrel0101770 58.00

Hader White Delrin Analog (2-Pack)0101765 36.00

Hader Aluminum Analog0101775 36.00

Hader Insertion Tool0101705 11.00

Hader Green Processing Spacers (6-Pack)0101703-6 36.00


Hader Alignment Housing (6-Pack)0101720-6 72.00



Hader Metal Housings (6-Pack)0101710-6 72.00



Hader White Riders- Reduced (6-Pack)0101753-6 36.00


Hader White Riders- Reduced (50-Pack)0101753-50 200.00Hader Bar

0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753

Hader Yellow Riders- Standard (6-Pack)0101752-6 36.00



11


11

11

Hader Bar

Hader Red Riders- Increased (6-Pack)0101754-6 36.00



Hader Blue Riders- Worn Bars (6-Pack)0101760-6 36.00



Metal Riders provide both rotational and vertical movement with a choice of two styles of acrylic retentions

Ackermann BL Clip SS0102108 32.00

Ackermann BL Clip SS (6-Pack)0102108-6 162.00

Ackermann MD Clip SS0102118 32.00

Ackermann MD Clip SS (6-Pack)0102118-6 162.00

Ackermann MD Clip GOLD0102119 44.00

Ackermann MD Clip GOLD (6-Pack)0102119-6 228.00

Ackermann BL Clip GOLD0102124 44.00

Ackermann BL Clip GOLD (6-Pack)0102124-6 228.00

Attachments

OVERDENTURE BARS

Metal Riders for H

ader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

45.00

11


11

11H

ader BarHader Red Riders- Increased (6-Pack)0101754-6 36.00















Attachments

OVERDENTURE BARS

Metal Riders for H

ader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

45.00

205.00

11


11

11

Hader Bar
















Attachments

OVERDENTURE BARS

Metal Riders for H

ader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

205.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




76.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




99-531021 58.00

50.00

45.00

15.00

16.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




112.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




112.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




45.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753



Hader Yellow Riders- Standard (50-Pack)0101752-50 200.00205.00

10


10

10

Had

er B

ar

Attachments

OVERDENTURE BARS


















0101710-6

0101720-6

0101703-6

0101705

0101765

0101770

0101753




205.00

45.00

11


11

11

Hader Bar
















Attachments

OVERDENTURE BARS

Metal Riders for H

ader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

0101752-6

0101754-6

0101760-6

11


11

11

Hader Bar
















Attachments

OVERDENTURE BARSM

etal Riders for Hader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

40-05050010

40-05000679

40-050527

40-052046

40-05050011

40-054747

40-055801

40-054746

40-05000681

40-052043

40-05000680

Ackermann Clip A - BL

Round Bar with Rider E (50mm)

CM Rider Clips (single)

Dolder Macro E (50mm)

Ackermann Clip B - MD

Dolder Macro E (25mm)

CM Rider Clips (5 pack)

Dolder Micro E (25mm)

Dolder Macro T (47.5mm)

Dolder Micro E (50mm)

Dolder Micro T (47.5mm)

45.00

45.00

45.00

202.00

252.00

156.00

290.00

115.00

221.00

114.00

105.00

40-05050011

(E)(T)

(K)

(E)(T)

(K)

IndicationRemovable dentures– Implant-supported dentures– CoverdenturesDolder® Bar AttachmentTooth- and tooth / gingival supported dentures (with preferably 3 or more abutments available):– Interdental (insertion) dentures,– Partial denturesDolder® Resilient BarTooth / gingival supported resilient dentures (placed primarily in upper and lower anterior regions):

Contraindication– Unilateral dentures without transverse support.– Restoration of abutment teeth with severe periodontal damage.– Hybrid dentures which are fitted with a single root cap.– Where patients have an existing allergy to one or more elements of the

attachment materials.– Unwillingness of the patient to correctly follow the aftercare / recall

instructions.– Patients with bruxism or further uncontrolled para-functional habits.

Description of the Dolder® systemBar-retained, removable restorations are among the most tried and tested forms of prosthetic treatment both experimentally and clinically and their relevance has increased due to advances in implantology.The Dolder® system, which includes the Dolder® bar attachment and the Dolder® resilient bar, is based on the successful Dolder® design and now includes new components to cater for market demands.

MaterialsDolder® male parts:E = Elitor®, warm straightened, high-grade, tough, yellow precious metal alloy. After soldering / laser welding the work must be hardened to attain the best mechanical properties.T = Pure titaniumK = Korak, plastic for the casting technique that burns out.Dolder® female parts:E = Elitor®, warm straightened, high-grade, tough, yellow precious metal alloy.D = DoralT = Pure titaniumG = Galak, for friction inserts, orally stable plastic (just as a spare part).

«Standard»: Horizontal positioning of retention. This is the well-tried design and is used primarily where there is little space available occlusally.

Setting the retention forceFemale part with adjustable lamellaThe retention force can be individually and accurately set using the Dolder® activator or deactivator. The posterior lamella, which is subjected to greater loading, is activated. The anterior lamella acts as a guide surface.

Limitation of useUnilateral dentures without a transversal connectorUse of the bar attachment titanium female part with plastic inserts on the resilient bar. This can lead to increased wear and tear because of the amount of free play.

Dolder® SystemAdjustable bar attachment and resilient bar for removable prosthetics

Characteristics– The original designed by Prof.

Dr E. Dolder

– Proven on the basis of many years’ clinical experience

– The standard for implant sup-ported bar restorations

– Extremely reliable stabilizing and splinting effect

Processing advantages– Large range of materials

and designs allows great-er flexibility with implant restorations!

– Time-saving and reliable pre-fabricated male parts in gold or pure titanium, which are connected to the primary unit by soldering or laser welding

– Good value male parts in high quality plastic

– Choice of two sizes micro + macro

– Maximum friction surfaces by customized adjustment of the lengths

Clinical advantages– A recess in the milled female

parts makes for a perfect fit and guarantees durable func-tioning. As a result, there is a noticeable slight snap action with the resilient bar.

– Bar-retained restoration enables safe immediate loading of implants. Please observe the implant manufacturer’s instructions for use.

– Splints and stabilizes weak abutment teeth

– Wide range of materials for the male parts

– Maximum, long-lasting friction due to optimally coordinated materials of the prefabricated parts

Bar attachment on 4 implants

Female parts «Standard»:

Execution in Elitor® (E)

Execution in Doral (D)

Execution in pure titanium (T)

Available male parts:Bar attachment:

Resilient bar:

The products carry the CE Mark. See packaging for details.For further instructions, warnings and for precautions please refer to the instructions for use.

66(E)

(T)(K)

(E)(T)

(K)

IndicationRemovable dentures– Implant-supported dentures– CoverdenturesDolder® Bar AttachmentTooth- and tooth / gingival supported dentures (with preferably 3 or more abutments available):– Interdental (insertion) dentures,– Partial denturesDolder® Resilient BarTooth / gingival supported resilient dentures (placed primarily in upper and lower anterior regions):

Contraindication– Unilateral dentures without transverse support.– Restoration of abutment teeth with severe periodontal damage.– Hybrid dentures which are fitted with a single root cap.– Where patients have an existing allergy to one or more elements of the



Description of the Dolder® systemBar-retained, removable restorations are among the most tried and tested forms of prosthetic treatment both experimentally and clinically and their relevance has increased due to advances in implantology.The Dolder® system, which includes the Dolder® bar attachment and the Dolder® resilient bar, is based on the successful Dolder® design and now includes new components to cater for market demands.

MaterialsDolder® male parts:E = Elitor®, warm straightened, high-grade, tough, yellow precious metal alloy. After soldering / laser welding the work must be hardened to attain the best mechanical properties.T = Pure titaniumK = Korak, plastic for the casting technique that burns out.Dolder® female parts:E = Elitor®, warm straightened, high-grade, tough, yellow precious metal alloy.D = DoralT = Pure titaniumG = Galak, for friction inserts, orally stable plastic (just as a spare part).

«Standard»: Horizontal positioning of retention. This is the well-tried design and is used primarily where there is little space available occlusally.

Setting the retention forceFemale part with adjustable lamellaThe retention force can be individually and accurately set using the Dolder® activator or deactivator. The posterior lamella, which is subjected to greater loading, is activated. The anterior lamella acts as a guide surface.

Limitation of useUnilateral dentures without a transversal connectorUse of the bar attachment titanium female part with plastic inserts on the resilient bar. This can lead to increased wear and tear because of the amount of free play.

Dolder® SystemAdjustable bar attachment and resilient bar for removable prosthetics

Characteristics– The original designed by Prof.

Dr E. Dolder

– Proven on the basis of many years’ clinical experience

– The standard for implant sup-ported bar restorations

– Extremely reliable stabilizing and splinting effect

Processing advantages– Large range of materials

and designs allows great-er flexibility with implant restorations!

– Time-saving and reliable pre-fabricated male parts in gold or pure titanium, which are connected to the primary unit by soldering or laser welding

– Good value male parts in high quality plastic

– Choice of two sizes micro + macro

– Maximum friction surfaces by customized adjustment of the lengths

Clinical advantages– A recess in the milled female

parts makes for a perfect fit and guarantees durable func-tioning. As a result, there is a noticeable slight snap action with the resilient bar.

– Bar-retained restoration enables safe immediate loading of implants. Please observe the implant manufacturer’s instructions for use.

– Splints and stabilizes weak abutment teeth

– Wide range of materials for the male parts

– Maximum, long-lasting friction due to optimally coordinated materials of the prefabricated parts

Bar attachment on 4 implants

Female parts «Standard»:

Execution in Elitor® (E)

Execution in Doral (D)

Execution in pure titanium (T)

Available male parts:Bar attachment:

Resilient bar:


66

40-052046

40-05000679

45-177600095.0045-1776000 Universal Plunger Loc Attachment


1966-2

1971-10

1969-10

8049

1971-2

Standard O-Ring Attachment Assembly (2-pack)

Micro O-Ring Attachment Assembly (10-pack)

Standard O-Ring Package (10-pack)

O-Ring Insertion Tool

Micro O-Ring Attachment Assembly (2-pack)

76.00

350.00

76.00

350.00

65.00

8049


16

16

O-Ring Overdenture Complete #3 w/housing1500532 48.00

1 Castable Male, 3 white final rings, 1 red processing ring, 1 metal retainer ring, and 1 processing analog.

O-Ring Overdenture Attachment #31500534 40.00

1 Castable Male, 3 white final rings, 1 red processing ring

O-Ring Castable Male Standard #31500530 10.00

O-Ring Overdenture Paralleling Mandrel #31500154 16.00

O-Ring Metal Retainer Standard #3 (ea)1500502 18.00

O-Ring Red Processing Rings #3 (12-Pack)1500505 27.00

O-Ring Black Rings Standard #3 (12-Pack)1500503 27.00

O-Ring White Rings Standard #3 (12-Pack)1500504 23.00

O-Ring Overdenture Analog Standard #31500506 16.00

O-Ring Implant Analog1600025 18.00

O-Ring Metal Retainer #41500204 27.00

O-Ring Black Rings #4 (6-Pack)1500194 30.00

O-Ring Overdenture Analog #41500214 27.00



O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025

O-Ring Black Rings #2M (6-Pack)1500197 27.00

O-Ring Mini Implant Analog #2M1500210 23.00

0101400 Preci Profile Straight 50mm 50.00 40.000101410 Preci Profile Curved 50mm 50.00 40.00

0102108 Ackermann BL Clip SS (2) 62.00 52.000102124 Ackermann BL Clip GOLD (2) 88.00 76.00

6 units0102118 Ackermann MD Clip SS (1) 31.00 26.000102119 Ackermann MD Clip GOLD (1) 44.00 38.00

Laser Weld Titanium Bars Titanium profiles for Laser welding wraparound Acrylic Implant Bridges

Metal Riders for Hader/Round BarsMetal Riders provide both rotational and vertical movement with a choice of two styles of acrylic retentions

O-Ring - Size ChartTo determine the correct size Oring needed, measure the retention zone (red line) -- or the area on the male post where the O-ring seats. Select the oring from the size chart with the closest matching internal diameter --to assure proper fit.The O-Ring Combo pack isa great option as well.

MD Retention BL Retention

Height: 2.9mm Length: 50mm Width: 2.0mm Vickers Hardness: 210

Straight Curved

3 units

5

7

O-Ring Replacement Size Chart Internal Diameter (ID) Outside Diameter (OD)

Sizing mm mmBlack #2 (12 pcs) Micro 1.00mm 3.60mmBlack #2M (6 pcs) 1.8 Mini Implant 1.20mm 3.60mmWhite #3 (12 pcs) Standard 1.40mm 4.50mmBlack #3 (12 pcs) Standard 1.40mm 4.50mmBlack #4 (6 pcs) Large 2.00mm 5.20mmBlack #5 (6 pcs) Extra Large 2.00mm 6.25mm

Metal Retainer Housing Ring#2 (Fits both #2 & #2M) Metal Retainer #3(ea).

Metal Retainer Rings #4 (ea).

Metal Retainer Rings #5 (ea).

1966-2

1971-2

SATURNO SATURNOTraditional

O-Rings

Up to 30º Angle Correction

ZEST ANCHORS2061 WINERIDGE PLACEESCONDIDO, CA 92029USA

TEL: 760.743.7744 OR 800.262.2310FAX: 760.743.7975EMAIL: [email protected]

DISTRIBUTED BY:

©2011 ZEST Anchors LLC. All rights reserved. ZEST® and LOCATOR® are registered trademarks and SATURNO™ is a trademark of ZEST IP Holdings, LLC.

SATURNO O-Ring ZEST Saturno remains inexcellent condition a� er

50,000 test cycles.

Traditional O-Ring Traditional O-Ring a� er

50,000 test cycles is non-functional.

SATURNO StandardPivoting O-Ring A� achmentUses 4.5mm outside diameter

O-Ring for 2.25mm Ball.

SATURNO Micro PivotingO-Ring A� achment

Uses 3.5mm outside diameterO-Ring for 1.8mm Ball.

Extensive laboratory testing has

demonstrated SATURNO™ O-Ring

Attachment to outperform traditional

O-Rings when tested at 15 degrees

of divergency.

1966-21966-101969-101971-21971-101974-10

Standard O-Ring A� achment Assembly (2-Pack)Standard O-Ring A� achment Assembly (10-Pack)Standard O-Ring Package (10-Pack)Micro O-Ring A� achment Assembly (2-Pack)Micro O-Ring A� achment Assembly (10-Pack)Micro O-Ring Package (10-Pack)

SATURNO Pivoting O-Ring A� achmentsO-Ring Insertion Tool Allows for easy insertion of the O-Ring into the Denture

Cap without damage to the O-Ring.

O-Ring insideinsertion tool.

Placement of O-Ringinside a� achment

assembly.

O-Ringseated insidea� achment

assembly.

Cap without

O-Ring inside

Cap without damage to the O-Ring.damage to the O-Ring.

O-Ring Insertion ToolO-Ring Insertion Tool 8049

11_ZES_008_SATURNO_DATA_SHEET.indd 2 4/12/11 2:11:24 PM


O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside





O-Rings




DISTRIBUTED BY:



50,000 test cycles.











of divergency.

1966-21966-101969-101971-21971-101974-10






assembly.


assembly.

Cap without

O-Ring inside




Up to 300 Angle Correction

OVERDENTURE STUD ATTACHMENTS



15

15

Attachments

OVERDENTURE STUD

The O-Ring Overdenture system features simple techniques, low cost, versatility, and is the most resilient option to protect weaker abutments 3.20mm tall 3.00mm Ø tooth surface 4.50mm Ø housing

O-Ring Black O-Ring Combo Pack (10-Pack)1500200 48.00

2 of each size of O-Ring (10 total): #2, #2M, #3, #4, and #5

O-Ring Insertion Tool4008049 62.00

time saver when working with smaller diameter o-rings

O-Ring Servicing Kit1500202 100.00

O-Ring Combo pack plus O-Ring Insertion Tool


1 Castable Male, 3 black final rings, 1 yellow processing ring, 1 metal retainer ring, and 1 processing analog.


1 Castable Male, 3 black final rings, 1 yellow processing ring

O-Ring Castable Male #2 Micro1500630 10.00

O-Ring Metal Retainer #2 & 2M1500602 18.00

O-Ring Yellow Processing #2 Micro (12-Pack)1500605 26.00

O-Ring Black Rings #2 Micro (12-Pack)1500603 27.00

O-Ring Overdenture Analog #2 Micro1500606 16.00

O-Ring Attachm

ent

1500501

1500603

1500210

1500200

4008049

1500632

1500602

O-Ring

O-Ring Closed Metal Housing MH-11500501 24.00

O-Ring Closed Metal Housing #2 MH-21500601 24.00

O-Ring Purple Rings #2 MH-2 Extra Strong (12)1500608 27.00

O-Ring Mini Implant Impression Copings1500212 20.00


15

15

Attachments

OVERDENTURE STUD

















O-Ring Attachm

ent

1500501

1500603

1500210

1500200

4008049

1500632

1500602

O-Ring






15

15

Attachments

OVERDENTURE STUD

















O-Ring Attachm

ent

1500501

1500603

1500210

1500200

4008049

1500632

1500602

O-Ring






15

15

Attachments

OVERDENTURE STUD

















O-Ring Attachm

ent

1500501

1500603

1500210

1500200

4008049

1500632

1500602

O-Ring





13.00

85.00

27.00

27.00

29.00

29.00

25.00

18.00

70.00

18.00

45.00

(6-pack)

(6-pack)

Mini Implant Analogs (4-pack)

Mini Implant Blockout Shims (25-pack)

70-1066-MNP0004

70-1066-MNP0005

70-1066-MN10001

45 -

45 -

45 -

45 -

45 -

45 -

45 -

45 -


16

16


















O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025




16

16


















O-Ri

ng A

ttac

hmen

t

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



29.00


16

16


















O-Ri

ng A

ttac

hmen

t

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



14.00


16

16


















O-Ri

ng A

ttac

hmen

t

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



25.00

25.00

18.00

21.00

58.50

56.75

52.00

52.00

48.00


16

16


















O-Ri

ng A

ttac

hmen

t

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



80.00(4-pack)


16

16


















O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025






20

20

Low profile resilient direct placement / post-coping overdenture attachment Black Mini: 3.50mm* tall, 3.30mm Ø housing, 3.50mm Ø tooth surface Green Standard: 4.50*mm tall, 3.80mm Ø housing, 4.00mm Ø tooth surface *the ST housing may be used instead of the standard housing to reduce vertical height by 1mm

ZAAG Kit of 4 Standard w/1-step drill4004011 290.00

1 step drill, 4 females, 4 males, 4 impression copings, 4 analogs, 2 parallel posts

ZAAG Kit of 4 Standard Refill Kit4004010 280.00

4 females, 4 males, 4 impression copings, 4 analogs, 2 parallel posts

ZEST/ZAAG Denture Cap Tool Kit4009201 64.00

Zest, ZAAG standard, and ZAAG mini nylon male removal tool and seating tool

ZAAG Female (Standard) (2-Pack)4014561 88.00

ZAAG Impression Male (Standard) (4-Pack)4014571 20.00

ZAAG Substitute Model Female (Standard) (4-Pack)4014572 44.00

ZAAG Parallel Post (Standard) (4-Pack)4014573 20.00

ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572

ZAAG Denture Cap Male (Standard) (2-Pack)4014321-2 44.00

ZAAG Denture Cap Male (Standard) (Oversize)4014322 22.00

ZAAG Replacement Male (Standard) (4-Pack)4014351 22.00

Preci Ball Decrease Retention Tool0101234 54.00

Preci Ball Increase Retention Tool0101236 54.00

Preci Ball/Clix Ball Paralleling Mandrel0101232 37.00

Preci Ball/Clix Analogue (2-Pack)0101230 44.00Pr

eci-B

all


20

20












ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572







Preci Ball/Clix Analogue (2-Pack)0101230 44.00

Prec

i-Bal

lPRODUCT NAMENUMBER PRICE

20

20












ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572








Prec

i-Bal

l


20

20












ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572








Prec

i-Bal

l


20

20












ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572








Prec

i-Bal

l

54.00

54.00

37.00

65.00

85.00

31.50

45.00

42.00

25.00

25.00

9201

4561-2

4571

4572

4321

4322

4543



22

22

The Original Zest Anchor system has been discontinued, but PREAT will maintain parts to service existing patients 3.50mm tall, 3.50mm Ø housing, 4.70mm Ø tooth surface Nylon Males for direct placement in Denture Base Resin (no housing)

ZEST ST Male (Combo Pack)4053262 38.00

ZEST ST Male (Standard) with Red Sleeve (4-Pack)4053317 18.00

ZEST ST Male (Oversized) with Yellow Sleeve (4-Pack)4053318 18.00

ZEST ST Male (Extra Oversize) with Orange Sleeve (4-Pack)4053319 18.00

Nylon Males for use with Metal Denture Caps

ZEST ST Replacement Male (Combo Pack)4073261 38.00

ZEST ST Replacement Male (Standard) (4-Pack)4073507 18.00

ZEST ST Replacement Male (Oversize) (4-Pack)4073508 18.00

ZEST ST Replacement Male (Extra Oversize) (4-Pack)4073509 18.00

ZEST ST Cap Male (2-Pack)4073334-2 38.00

ZEST ST Cap Male (Oversize) (2-Pack)4073335-2 38.00

ZEST ST Cap Male (Extra Oversize) (2-Pack)4073336-2 38.00

ZEST Blue Transfer Male with Blue Sleeve..(4-Pack)4053381 18.00

ZEST Substitute Female (4-Pack)4053563 18.00

Zest

Anc

hor

Attachments

OVERDENTURE STUD

4073337

4073334-2

4053317

4073507

Zest Female

Zest

4014921

4014911

20.00

20.00

20.00

3317

3318

3319


22

22
















Zest

Anc

hor

Attachments

OVERDENTURE STUD

4073337

4073334-2

4053317

4073507

Zest Female

Zest

4014921

4014911

50.003507


22

22
















Zest

Anc

hor

Attachments

OVERDENTURE STUD

4073337

4073334-2

4053317

4073507

Zest Female

Zest

4014921

4014911

38.00

38.00

38.00

38.00

38.00

3334-2

3335-2

3336-2

3381

3563


20

20












ZAAG

Attachments

OVERDENTURE STUD

ZAAG

ZAAG Male

Std Female

Mini Female

4004011

4009201

4014561

4014572








Prec

i-Bal

l



21

21

ZAAG ST Replacement Male (Standard) (Oversized) (4-Pack)4014534 22.00

ZAAG Female (Mini) (2-Pack)4014562-2 88.00

ZAAG Impression Male (Mini) (4-Pack)4014581 20.00

ZAAG Substitute Model Female (Mini) (4-Pack)4014582 44.00

ZAAG Parallel Post (Mini) (4-Pack)4014583 20.00

ZAAG Denture Cap Male (Mini) (2-Pack)4014325-2 44.00

ZAAG Male Denture Cap (Mini) Oversize4014326 22.00

ZAAG Replacement Male (Mini) (4-Pack)4014353 22.00

ZAAG Replacement Male (Mini) (Oversize) (4-Pack)4014354 22.00

ZAAG ST Denture Cap Male Mini (2)4014335 44.00

ZAAG Replacement Male (Mini ST) (4 Pack)4014543 22.00

ZAAG Replacement Male (Mini ST) (Oversize) (4-Pack)4014544 22.00

ZAAGAttachments

OVERDENTURE STUD

4014543

4014353

4014325

4014562

4014533

4014331

4014351

4014321

ZAAG One-Step Drill (Standard)4014911 40.00

ZAAG One-Step Drill (Mini)4014921 40.00

ZAAG Diamond Bur (Mini)4014922 27.00

ZAAG Replacement Male (Standard) (Extra Oversize) (4-Pack)4014549 22.00

ZAAG ST Cap Male (Standard) (2-Pack)4014331 44.00

ZAAG ST Cap Male (Standard) (Oversize)4014332 22.00

ZAAG ST Replacement Male (Standard) (4-Pack)4014533 22.00

ZAAG Replacement Male (Standard) (Oversize) (4-Pack)4014352 22.0025.00

28.00

47.00

25.00

25.00

25.00

25.00

35.00

35.00

42.00

25.00

25.00

40.00

40.00

47.00

88.00

31.50

45.00

18.75

46.00

4352

4549

4331-2

4332

4533

4534

4562-2

4581

4582

4583

4325-2

4326

4353

4354

4335-2

4543

4544

4911

4921

4922



21

21

ZAAG ST Replacement Male (Standard) (Oversized) (4-Pack)4014534 22.00

ZAAG Female (Mini) (2-Pack)4014562-2 88.00

ZAAG Impression Male (Mini) (4-Pack)4014581 20.00

ZAAG Substitute Model Female (Mini) (4-Pack)4014582 44.00

ZAAG Parallel Post (Mini) (4-Pack)4014583 20.00

ZAAG Denture Cap Male (Mini) (2-Pack)4014325-2 44.00

ZAAG Male Denture Cap (Mini) Oversize4014326 22.00

ZAAG Replacement Male (Mini) (4-Pack)4014353 22.00

ZAAG Replacement Male (Mini) (Oversize) (4-Pack)4014354 22.00

ZAAG ST Denture Cap Male Mini (2)4014335 44.00

ZAAG Replacement Male (Mini ST) (4 Pack)4014543 22.00

ZAAG Replacement Male (Mini ST) (Oversize) (4-Pack)4014544 22.00

ZAAG

Attachments

OVERDENTURE STUD

4014543

4014353

4014325

4014562

4014533

4014331

4014351

4014321

ZAAG One-Step Drill (Standard)4014911 40.00

ZAAG One-Step Drill (Mini)4014921 40.00

ZAAG Diamond Bur (Mini)4014922 27.00

ZAAG Replacement Male (Standard) (Extra Oversize) (4-Pack)4014549 22.00

ZAAG ST Cap Male (Standard) (2-Pack)4014331 44.00

ZAAG ST Cap Male (Standard) (Oversize)4014332 22.00

ZAAG ST Replacement Male (Standard) (4-Pack)4014533 22.00

ZAAG Replacement Male (Standard) (Oversize) (4-Pack)4014352 22.00

(Reg.)


ERA-RV Metal Jacket - Partial

811168

ERA RV Impression Coping

811232

ERA/ERA-RV partial denture processing jig

811250

The ERA attachment system is Sterngold’s response to the dental professionals need for simple, dependable and highly versatile attachment system for removable prostheses. Sterngold is used in removable partial dentures treatment, tooth supported overdentures and implant cases, ERA is an excellent choice for both experienced practitioners and those new to attachment procedures.

ERAMicro ERA Starter Kit 811011

Micro Partial ERA Metal Jacket 811021

Micro ERA Partial Denture Impression Coping 811235

Micro Partial ERA Male Black - (5) 811013

Micro Partial ERA Male White (5) 811014

Micro Partial ERA Male Orange (5) 811015

Micro Partial ERA Male Blue (5) 811016

Micro Partial ERA Male Grey (5) 811017

Micro Partial ERA Male Yellow (5) 811018

Micro Partial ERA Male Red (5) 811019

Micro Partial ERA Male Assorted 7 811009

Micro ERA Female 811010

Micro ERA Partial Denture Processing Jig 811020

Micro ERA Laboratory Tool Kit 811025

Micro ERA Dentist Tool Kit 811026

Micro ERA Core Cutter Bur 811023

Micro ERA Seating Tool 811022

Micro ERA Paralleling Mandrel 811024

EZ PickUp™ Syringe and Tips (Self-Curing) 220235

Stern ERA-RV Starter kit 811115

ERA-RV Metal Jacket - Partial 811168

ERA RV Impression Coping 811232

ERA Male Black RV Partial 5 811125

ERA Male White RV Partial (5) 811135

ERA Male Orange RV Partial (5) 811145

ERA Male Blue RV Partial (5) 811155

ERA Male Grey RV Partial (5) 811165

ERA Male Yellow RV Partial (5) 811175

ERA Male Red RV Partial (5) 811176

ERA Male Assorted RV Partial (7) 811166

ERA Female only 811190

ERA/ERA-RV partial denture processing jig 811250

ERA Laboratory Tool kit 811200

ERA Dentist Tool Kit 811240

ERA core cutter bur 811220

ERA seating tool 811230

ERA paralleling mandrel 811210


Stern ERA Micro Complete Attachment - Starter kit - 811012Extracoronal semi-precision attachment - 811011

Kit contents: 1 female, 2 black males, 2 white males, and 1 orange male

Stern ERA-RV Partial Attachment - Starter kit - 811115 Resilient semi-precision attachmentContents: 1 female and 2-Black males 2-white males, and 1 orange male

77.25

59.75

74.50

52.50

52.50

52.50

52.50

52.50

52.50

52.50

72.75

63.50

27.75

110.75

61.75

37.25

37.25

63.70

150.00

77.25

59.75

74.50

52.50

52.50

52.50

52.50

52.50

52.50

52.50

72.75

63.50

27.75

110.75

61.75

37.25

37.25

63.70

150.00


Black is the processing maleWhite = smallest button diamater (least retention)OrangeBlueGreyYellowRed = largest button diamater (most retention)

The six different males provide consistent retention throughout the life of the attachment. ERA Males use the same colour code.

Stern ERA Overdenture Starter Kit 811300

ERA Metal Jacket Overdenture 811380

ERA Overdenture Impression Coping 811233

ERA Male Black Overdenture (5) 811320

ERA Male White Overdenture (5) 811330

ERA Male Orange Overdenture (5) 811340

ERA Male Blue Overdenture(5) 811350

ERA Male Grey Overdenture (5) 811360

ERA Male Yellow Overdenture (5) 811370

ERA Male Red Overdenture (5) 811375

ERA Male Assorted Overdenture (7) 811365

ERA Overdenture female 811390

ERA Overdenture processing jig 811395

ERA Laboratory Tool kit 811200

ERA Dentist Tool Kit 811240

ERA core cutter bur 811220

ERA seating tool 811230

ERA paralleling mandrel 811210


Micro ERA Overdenture Starter Kit 811045

Micro ERA Metal Jacket Overdenture 811043

Micro ERA Overdenture Impression coping 811236

Micro ERA Male Black Overdenture, 5 811035

Micro ERA Male White Overdenture 5 811036

Micro ERA Male Orange Overdenture 5 811037

Micro ERA Male Blue Overdenture 5 811038

Micro ERA Male Grey Overdenture 5 811039

Micro ERA Male Yellow Overdenture 5 811040

Micro ERA Male Red Overdenture 5 811041

Micro ERA Male Assorted Overdenture 7 811029

Micro ERA Overdenture Female 811030

Micro ERA Overdenture Processing Jig 811042

Micro ERA Laboratory Tool Kit 811025

Micro ERA Dentist Tool Kit 811026

Micro ERA Core Cutter Bur 811023

Micro ERA Seating Tool 811022

Micro ERA Paralleling Mandrel 811024


Stern ERA Overdenture Attachment - 811310Resilient semi-precision attachment

Contents: 1 female and 2-Black males 2-white males, and 1 orange male

Stern ERA Overdenture Attachment - 811310Resilient semi-precision attachmentContents: 1 female and 2-Black males 2-white males, and 1 orange male

ERA PickUp Syringe and Tips (63-220235)1 Syringe @ 15 grams and 15 tips

77.25

59.75

74.50

52.50

52.50

52.50

52.50

52.50

52.50

52.50

72.75

63.50

27.75

110.75

61.75

37.25

37.25

63.70

150.00

77.25

59.75

74.50

52.50

52.50

52.50

52.50

52.50

52.50

52.50

72.75

63.50

27.75

110.75

61.75

37.25

37.25

63.70

150.00


055 752

055 698

0500 0214

055 887

05050060

05050061

05050062

05050042

05050043

05050044

051 462

051 481

051 366

051 618

051 619

070 340

070 342

055 771

Dalbo Plus (Standard) Female part TE basic complete

Dalbo Classic Female part E basic

Dalbo Plus Tuning female part soft TE basic complete

Dalbo Classic Female part E elliptic

Pro-Snap Housing T yellow

Pro-Snap Housing T Red

Pro-Snap Housing T Green

Pro-Snap Retention Insert G Yellow

Pro-Snap Retention Insert G Red

Pro-Snap Retention Insert G Green

Biloc® KD

Biloc® KC

Biloc® Male part C

Biloc® Male part D

Biloc® Female part K

Biloc® Parallelometer insert

Activator

Dalbo Plus Tuning female part TE basic complete

110.00

106.00

105.00

60.00

75.00

75.00

75.00

75.00

100.00

100.00

100.00

90.00

140.00

135.00

80.00

18.00

17.50

39.00

055 752

055 887

05050060

051 462

051 366

CENDRES METAUX ATTACHMENTS

11


11

11

Hader Bar
















Attachments

OVERDENTURE BARS

Metal Riders for H

ader/Round Bars

Ackermann

0101752

0101754

0101760

0102108

0102118

0102119

0102124

Dalbo®-PLUS

TuningTuning softStandard

The Dalbo®-PLUS female part basicis indicated for integration in the laboratory. It can either be directly polymerized or resin-bonded in the housing. The duplicating aid/spacer that comes with the product facilitates the manufacturing process of a box for bonding in the laboratory.

The Dalbo®-PLUS female part ellipticis indicated for direct (chairside) fixation. Experiments have shown that resin quality is reduced by direct (chairside) integration and that under high stress-loads, the female part may get extracted from the denture. Our solution is an elliptically shaped female part which significantly increases the retentive force in the denture’s body!

Retentive force in the denture’s body: A comparison of the Dalbo® female partsUnder laboratory conditions, all female parts for ball anchors have a sufficient retention in the denture’s body. What’s remarkable is that in some cases the Dalbo®-PLUS female part elliptic displays values exceeding that of the mechanical properties of the resin.

The lamellae retention insertis the actual retentive element in the system. It is made of Elitor®, which is a yellow precious metal alloy with ideal mechanical properties for long-term, reliable functioning. The insertion is quick and simple. Just unscrew the insert from the housing with the special screwdriver/activator without extracting the female part from the denture’s body.

The Tuning lamellae retention insertsTwo special tuning retention inserts with reduced inner diameter provide an extraordinarily wide range of friction and allow retention to be restored.

Choosing the right retention insert

Basic version Duplicating aid

Elliptic version

Standard version(no indentation)

Tuning soft version(1 indentation)

Tuning version(2 indentations)

Optimal range of action

Maximal range of action

2.27 2.26 2.25 2.24 2.23 2.22 2.21 2.20 2.19 2.18 2.17 2.16 2.15

in mm

2.27 2.26 2.25 2.24 2.23 2.22 2.21 2.20 2.19 2.18 2.17 2.16 2.15

in mm

Retentive force from the denture’s body for female parts

Reference Dalbo®-B

Dalbo®-Classic

Dalbo®-Classic elliptic

Dalbo®-PLUS basic

Dalbo®-PLUS elliptic

Retentive force [N]

0 200 400 600 800 1000 1200 1400

38

2.224.04.0

3.12.5

3.4

Pro-SnapSupraradicular, resilient and retentive anchor

Advantages:The retention force can easily be adjusted by changing the retention inserts.3 force degrees: yellow soft, red middle and green strong

IndicationsRemovable, rigidly or resiliently restorations supported on implants and root caps:– Hybrid dentures– Unilateral free-end dentures locked transversally– lnsertion / free-end dentures in combination

Contraindications– Unilateral dentures without transverse support.– Restoration of abutment teeth with severe periodontal damage.– Hybrid dentures which are fitted with a single root cap.– Where patients have an existing allergy to one or more elements of the



1:1 Order No. Parts Description

05050033 05050037 05050060

Pro-Snap TC yellow Male part C Housing T yellow

Complete For soldering onto root caps. For polymerizing into denture resin

05050034 05050037 05050061

Pro-Snap TC red Male part C Housing T red


05050035 05050037 05050062

Pro-Snap TC green Male part C Housing T green


05050036 05050038 05050060

Pro-Snap TK yellow Male part K Housing T yellow

Complete Burnout plastic For polymerizing into denture resin

070 131 Parallelometer insert For mounting of the male part

07050004 07050005

07050006

05050042 * 05050043 * 05050044 *

07050008

Protection cap Transfer jig

Stabilizing Ring G

Retention insert G yellow Retention insert G red Retention insert G green

Seating tool

For master model

Here the spacers generally replace the anchor female parts during resin-polymerization in the dental laboratory. Retentive force soft Retentive force middle Retentive force strong * Delivery unit: package of six

To insert the retention insert with stabilizing ring into housing


45

05050042

2.224.04.0

3.12.5

3.4

Pro-SnapSupraradicular, resilient and retentive anchor

Advantages:The retention force can easily be adjusted by changing the retention inserts.3 force degrees: yellow soft, red middle and green strong

IndicationsRemovable, rigidly or resiliently restorations supported on implants and root caps:– Hybrid dentures– Unilateral free-end dentures locked transversally– lnsertion / free-end dentures in combination

Contraindications– Unilateral dentures without transverse support.– Restoration of abutment teeth with severe periodontal damage.– Hybrid dentures which are fitted with a single root cap.– Where patients have an existing allergy to one or more elements of the



1:1 Order No. Parts Description

05050033 05050037 05050060

Pro-Snap TC yellow Male part C Housing T yellow


05050034 05050037 05050061

Pro-Snap TC red Male part C Housing T red


05050035 05050037 05050062

Pro-Snap TC green Male part C Housing T green


05050036 05050038 05050060

Pro-Snap TK yellow Male part K Housing T yellow

Complete Burnout plastic For polymerizing into denture resin

070 131 Parallelometer insert For mounting of the male part

07050004 07050005

07050006

05050042 * 05050043 * 05050044 *

07050008

Protection cap Transfer jig

Stabilizing Ring G

Retention insert G yellow Retention insert G red Retention insert G green

Seating tool

For master model

Here the spacers generally replace the anchor female parts during resin-polymerization in the dental laboratory. Retentive force soft Retentive force middle Retentive force strong * Delivery unit: package of six

To insert the retention insert with stabilizing ring into housing


45


$125.00

$66.00$85.00

$285.00

0 mm 0.73 mm 1.0 mm 2.0 mm 3.0 mm 4.0 mm 5.0 mm 6.0 mm 7.0 mm 8.0 mm

3.5, ST (M2.0 thread) 8636(0.81mm) 8637 8638 8639 86404.0, ST (M2.0 thread) 8657 8658 8659 86604.5, 5.0, ST (M2.0 thread)(Lilac) 8686(0.5mm) 8687 8688 8689 8690

3.5 (yellow) EXTERNAL HEX 8531 8532 8533 8534 85354.0 (green) EXTERNAL HEX 8541 8542 8543 8544 8545

5.0 (blue) EXTERNAL HEX 8551 (1.5 mm)

8552 (2.5 mm)

8553 (3.5 mm)

8554(4.5 mm)

8555(5.5 mm)

3.0 INTERNAL LASER LOCK 1927 1928 1929 1930

3.5 (yellow) INTERNAL HEX 8661 8662 8663 (2.5 mm)

8664 (3.5 mm)

8665 (4.5 mm)

8625 (5.5 mm)

8626 (6.5 mm)

4.5 (green) INTERNAL HEX 8671 8672 8673 8674 8675 8627 86285.7 (blue) INTERNAL HEX 8190 8191 8192 8193 8194 8195

3.25 MICROMINIPLANT EXTERNAL HEX 8441 8442 8443 8444 8445 84463.75 MINIPLANT EXTERNAL HEX 8681 8682 8683 8684 8685 86964.0 CYLINDRICAL EXTERNAL HEX 8681 8682 8683 8684 8685 8696

3i 5.0 EXTERNAL HEX 8820(0.6 mm)

8821 8822 8823 8824

TG 8621 8622 8623 86243.4 CERTAIN INTERNAL MICRO IMPLANT 8431 8432 8433 8434 8435 84364.1 CERTAIN INTERNAL (Fits Certain 5.0 & 6.0) 8630 8631 8632 8633 8634 8635

NOBELACTIVE (NP) 3.5 Conical Connection 2069 2070 2071 2072 2073 2074NOBELACTIVE (RP) 4.3/5.0 Conical Connection 2075 2076 2077 2078 2079 2080SELECT, REPLACE 3.5 (Purple) Internal Tri Lobe 8756 8757 8758 8759 8760 8734 8735SELECT, REPLACE 4.3 (Gold) Internal Tri Lobe 8761 8762 8763 8764 8765 8753 8754SELECT, REPLACE 5.0 (Blue) Internal Tri Lobe 8766 8767 8768 8769 8770NOBEL SPEEDY REPLACE (GROOVY) 4.0 8761 8762 8763 8764 8765 8753 8754BRANEMARK 3.3 (NP) EXTERNAL HEX 8105 8106 8107 8108 8109BRANEMARK 3.75, 4.0, 5.0 (RP) EXTERNAL HEX 8681 8682 8683 8684 8685 8696

BRANEMARK 5.0 (WP) EXTERNAL HEX 8825(1.1 mm)

8826 8827 8828 8829

NOBEL SPEEDY EXT HEX (GROOVY) 4.0 8681 8682 8683 8684 8685 8696NOBEL SPEEDY EXT HEX (GROOVY) 3.5 8105 8106 8107 8108 8109REPLACE 3.5 EXTERNAL HEX 8676 8677 8678 8679 8680REPLACE 4.3 EXTERNAL HEX 8781 8782 8783 8784 8785

REPLACE 5.0 EXTERNAL HEX 8835(1.37 mm)

8836 8837 8838 8839

SCS Bone level NC 3.5mm (Yellow) SCS Bone level RC 4.1mm (Purple)

3.5mm GS Mini Internal / HG Mini

4.0mm GS Standard Internal / HG Standard

1561 1562 1563 1564 1565 1566

1551 1552 1553 1554 1555 1556

PRODUCT CODE

LOCATOR IMPLANT ATTACHMENT PRODUCT CODES

STRAUMANN

(see table below)

8519-108519-2

ASTRA TECH / DENTSPLY IH AB

HEIGHT OF ABUTMENT TISSUE CUFF ABOVE THE IMPLANT

BIOMET (3i)

PRICE (CAD)LOCATOR SYSTEMS COMPONENTS

$66.008540-10 $285.00

LOCATOR Implant Abutment

NOBEL BIOCARE

LOCATOR Extended Range Male Processing Package (10 Pack)8540-2

LOCATOR Core Tool (includes abutment driver)LOCATOR Male Processing Package (2 Pack)LOCATOR Male Processing Package (10 Pack)LOCATOR Extended Range Male Processing Package (2 Pack)

8393

8656(0.5mm)

3.5/4.0 (M1.6 thread) (Aqua)

3.6 LOC Abutment

8115 8116 8117 8118 8119

02790 02791 02792 02793 027944.2 LOC Abutment 02795 02796 02797 02798 027994.8 LOC Abutment 02800 02801 02802 02803 02804

(1.25 mm)

BIOHORIZON/ZIMMER/MIS7

ASTRA EV

HIOSSEN

8422 8423 8424 8425 84268170 8171 8172 8173 8174 8175

Tissue Level NNC 3.5mmTissue Level RN 4.8mm

2056 2057 2058 2059 2060 20618742 8743 8744 8745 8751 8752

Tissue Level WN 6.5mm 8870 8871 8872 8873 8874

LOCATOR ABUTMENTSLEGACYORIGINAL



34

34

The Locator attachment is the most popular stud attachment in the world due to its angle correction, ease of use, low profile 9 different retention levels to meet patient’s needs, and patented PIVOT between the housing and nylon male that reduces potential wear on the abutment. *Beware imitations that do not pivot* 2.73mm vertical, 5.45mm Ø

LOCATOR 35n Square Driver (15mm)4008260 48.00

For use with Straumann torque wrenches



LOCATOR Insert Driver (Latch 23mm)4008913 48.00


LOCATOR Square Insert Driver (15mm)4008926 48.00


LOCATOR Core Tool4008393 82.00

LOCATOR Gold Driver4008390 38.50

LOCATOR Male Removal Tool4008397 33.50

LOCATOR Abutment Carrier (4-Pack)4008394 21.00

LOCATOR Demo Model4009006 240.00

LOCATOR Root Model4009014 215.00

LOCATOR Implant Model w/External Hexed Implants4009015 240.00

LOCATOR Impression Coping (4-Pack)4008505 68.50

LOCATOR Impression Coping (20-Pack)4008505-20 306.00

Loca

tor S

elf A

ligni

ng

Attachments

IMPLANT ABUTMENTS/ATTACHMENTS

4008260

4008913

4008926

4008393

4008394

4008505

Locator

LocatorPRODUCT NAMENUMBER PRICE

34

34



















Loca

tor S

elf A

ligni

ng

Attachments


4008260

4008913

4008926

4008393

4008394

4008505

Locator

Locator

68.00

73.00

75.00

68.00

75.00

75.00

85.00

48.00

38.00

25.00

260.00

75.00

335.00

8260

8280

8913

8914

8926

8927

8393

8390

8397

8394

9015

8505

8505-20


34

34



















Loca

tor S

elf A

ligni

ng

Attachments


4008260

4008913

4008926

4008393

4008394

4008505

Locator

Locator


34

34



















Loca

tor S

elf A

ligni

ng

Attachments


4008260

4008913

4008926

4008393

4008394

4008505

Locator

Locator



34

34



















Loca

tor S

elf A

ligni

ng

Attachments


4008260

4008913

4008926

4008393

4008394

4008505

Locator

Locator



35

35

LOCATOR Female Analog (4.0mm) (4-Pack)4008530 68.50

The 4mm Ø analog is for Narrow and Regular Platform Implants

LOCATOR Female Analog (4.0mm) (20-Pack)4008530-20 306.00


The 5mm Ø analog is for Wide Platform Implants and Natural Teeth


LOCATOR Parallel Post (4-Pack)4008517 18.00

LOCATOR Black Processing Male (4-Pack)4008515 23.00

LOCATOR Processing Replacement Male (Black) (20-Pack)4008515-20 104.00

LOCATOR Replacement Male (Clear) (4-Pack)4008524 23.00

LOCATOR Replacement Male (Clear) (20-Pack)4008524-20 104.00

LOCATOR Light Retention Replacement Male (Pink) (4-Pack)4008527 23.00

LOCATOR Light Retention Replacement Male (Pink) (20-Pack)4008527-20 104.00

LOCATOR Extra Light Retention Replacement Male (Blue) (4-Pack)4008529 23.00

LOCATOR Replace Male Blue- Decreased (20-Pack)4008529-20 104.00

LOCATOR Extended Range Replacement Male (Green) (4-Pack)4008547 23.00

LOCATOR Extended Range Replacement Male (Green) (20-Pack)4008547-20 104.00

LOCATOR Extra Light Retention Extended Range Replacement Male (Red) (4-Pack)

4008548 23.00


4008548-20 104.00

LOCATOR Extended Range Replacement Male (Orange) (4-Pack)4008915 23.00

Locator Self Aligning

Attachments


4008548

4008547

4008529

4008527

4008524

4008515

4008516

4008530

75.00

335.00

335.00

75.00

20.00

25.00

25.00

25.00

25.00

25.00

25.00

25.00

120.00

120.00

120.00

120.00

120.00

120.00

8530

8530-20

8516

8517

8515

8515-20

8524

8527

8529

8547

8548

8548-20

8915

8547-20

8529-20

8527-20

8524-20

8516-20


35

35


The 4mm Ø analog is for Narrow and Regular Platform Implants



The 5mm Ø analog is for Wide Platform Implants and Natural Teeth


LOCATOR Parallel Post (4-Pack)4008517 18.00

LOCATOR Black Processing Male (4-Pack)4008515 23.00

LOCATOR Processing Replacement Male (Black) (20-Pack)4008515-20 104.00

LOCATOR Replacement Male (Clear) (4-Pack)4008524 23.00

LOCATOR Replacement Male (Clear) (20-Pack)4008524-20 104.00

LOCATOR Light Retention Replacement Male (Pink) (4-Pack)4008527 23.00

LOCATOR Light Retention Replacement Male (Pink) (20-Pack)4008527-20 104.00

LOCATOR Extra Light Retention Replacement Male (Blue) (4-Pack)4008529 23.00

LOCATOR Replace Male Blue- Decreased (20-Pack)4008529-20 104.00

LOCATOR Extended Range Replacement Male (Green) (4-Pack)4008547 23.00

LOCATOR Extended Range Replacement Male (Green) (20-Pack)4008547-20 104.00


4008548 23.00


4008548-20 104.00

LOCATOR Extended Range Replacement Male (Orange) (4-Pack)4008915 23.00


Attachments


4008548

4008547

4008529

4008527

4008524

4008515

4008516

4008530



34

34



















Loca

tor S

elf A

ligni

ng

Attachments


4008260

4008913

4008926

4008393

4008394

4008505

Locator

Locator



36

36

LOCATOR Extended Range Replacement Male (Orange) (20-Pack)4008915-20 104.00

LOCATOR Zero Retention Extended Range Replacement Male (Gray) (4-Pack)

4008558 23.00


4008558-20 104.00

LOCATOR High Retention Replacement Male (Purple) (4-Pack)4008559 35.00

LOCATOR Bar Processing Replacement Male (Yellow) (4-Pack)4008026 23.00

LOCATOR Bar Processing Replacement Male (Yellow) (20-Pack)4008026-20 104.00

LOCATOR Processing Spacer (4-Pack)4008569 31.00

LOCATOR Processing Spacer (20-Pack)4008569-20 140.00

LOCATOR Replacement Denture Cap Male Assembly (4-Pack)4008510-4 56.00


LOCATOR Male Processing Package (2-Pack)4008519-2 63.50

TI housing, blockout spacer, blue / pink / clear males


LOCATOR Extended Range Male Processing Package (2-Pack)4008540-2 63.50

TI housing, blockout spacer, red / orange / green males


LOCATOR Male Processing Package SS (2-Pack)..4008550-2 63.50

Stainless Steel housing ideal for welding to CoCr framework

SS housing, blockout spacer, blue / pink / clear males

LOCATOR Male Processing Package SS (10-Pack)4008550-10 284.00

Attachments


Loca

tor S

elf A

ligni

ng

4008550

4008540

4008519

4008510

4008569

4008026

4008559

4008558


36

36

LOCATOR Extended Range Replacement Male (Orange) (20-Pack)4008915-20 104.00


4008558 23.00


4008558-20 104.00

LOCATOR High Retention Replacement Male (Purple) (4-Pack)4008559 35.00

LOCATOR Bar Processing Replacement Male (Yellow) (4-Pack)4008026 23.00

LOCATOR Bar Processing Replacement Male (Yellow) (20-Pack)4008026-20 104.00

LOCATOR Processing Spacer (4-Pack)4008569 31.00

LOCATOR Processing Spacer (20-Pack)4008569-20 140.00




TI housing, blockout spacer, blue / pink / clear males



TI housing, blockout spacer, red / orange / green males


LOCATOR Male Processing Package SS (2-Pack)..4008550-2 63.50

Stainless Steel housing ideal for welding to CoCr framework

SS housing, blockout spacer, blue / pink / clear males

LOCATOR Male Processing Package SS (10-Pack)4008550-10 284.00

Attachments


Loca

tor S

elf A

ligni

ng

4008550

4008540

4008519

4008510

4008569

4008026

4008559

4008558

8915-20

8558

8558-20

8559

8026

8026-20

8569

8569-20

8510-4

8510-10

8519-2

8519-10

8540-2

8540-10

8550-2

8550-10

120.00

120.00

120.00

160.00

145.00

285.00

285.00

285.00

25.00

25.00

35.00

65.00

66.00

66.00

66.00

46.00




37

37

LOCATOR Bar Male Processing (2-Pack)4008028-2 63.50

TI housing. w/ yellow, 2 block. spacers, blue / pink / clear


LOCATOR Refill Kit4008010 322.00

Four 0° females, 2 parallel posts, 4 complete males

LOCATOR Starter Kit4008011 343.00

Spotface Drill, Pilot Drill, Four 0° females, 4 complete males, 2 parallel posts

LOCATOR Refill Coping Kit4008050 322.00

4 Cast-to females w/parallel posts, 4 complete males

LOCATOR Coping Kit4008051 343.00

Spotface Drill, Pilot Drill, 4 Cast-to females w/parallel posts, 4 complete males

LOCATOR Refill Mixed Kit4008070 322.00

Two 0°, One 10°,One 20° females, 2 parallel posts, 4 complete males

LOCATOR Mixed Kit4008071 343.00

Spotface Drill, Pilot Drill, Two 0°, One 10°,One 20° females, 2 parallel posts, 4 complete males

LOCATOR Spotface Diamond Bur4008922 28.00

LOCATOR Pilot Drill4008924 19.00

LOCATOR 0 Degree Female (2-Pack)4008520-2 99.00



Attachments



4008028

Locator

4008011

4008071

4008922

4008924

4008520

4008521


37

37





















Attachments



4008028

Locator

4008011

4008071

4008922

4008924

4008520

4008521


37

37





















Attachments



4008028

Locator

4008011

4008071

4008922

4008924

4008520

4008521

8028-2

8028-10

8922

8924

8520-2

8521-2


37

37





















Attachments

IMPLANT ABUTMENTS/ATTACHMENTSLocator Self Aligning

4008028

Locator

4008011

4008071

4008922

4008924

4008520

4008521


37

37





















Attachments



4008028

Locator

4008011

4008071

4008922

4008924

4008520

4008521

66.00

48.00

28.00

126.00

126.00

285.00


39

39

LOCATOR 2-56 Bar Tap (2-56 Thread)4009105 28.00

LOCATOR Paralleling Mandrel for Bar Female4009107 38.50

LOCATOR for Multi-Unit Abutment TI (2-Pack)4008909-2 260.00

Attachments



4008909

4009107




38

38




LOCATOR 0 Degree Cast-to Female (2-Pack)4008528-2 99.00


LOCATOR Cast-To Bar Female (2-Pack)4008586-2 87.50


LOCATOR Bar Female 2-56 Thread (2-Pack)4008587-2 87.50

LOCATOR Laser Bar Female, Titanium (2-Pack)4008588-2 87.50


LOCATOR Bar Female, 2.0mm Thread (2-Pack)4008589-2 87.50


LOCATOR Laser Bar Female, Stainless Steel (2-Pack)4008590-2 87.50


LOCATOR 2-56 castable sleeve4008013 55.00

LOCATOR 2mm Castable Threaded Inserts (10-Pack)4008014 55.00

LOCATOR Tap Holder4008016 60.00

1.7mm Bar Drill (2.0mm Thread)4009102 15.00

1.8mm Bar Drill 2-56 Thread4009103 15.00

2.0mm Bar Tap (2.0mm Thread)4009104 28.00

Attachments


Loca

tor S

elf A

ligni

ng

4008522

4008528

4008586

4008588

4008589

4008014

4008016

4009102


38

38





















Attachments


Loca

tor S

elf A

ligni

ng

4008522

4008528

4008586

4008588

4008589

4008014

4008016

4009102


38

38





















Attachments


Loca

tor S

elf A

ligni

ng

4008522

4008528

4008586

4008588

4008589

4008014

4008016

4009102


39

39

LOCATOR 2-56 Bar Tap (2-56 Thread)4009105 28.00

LOCATOR Paralleling Mandrel for Bar Female4009107 38.50


Attachments



4008909

4009107

9105

9107

8909-2

8522-2

8528-2

8586-2

8586-10

8587-2

8588-2

8588-10

8589-2

8589-10

8590-2

8590-10

8013

8014

8016

9102

9103

9104


38

38





















Attachments


Loca

tor S

elf A

ligni

ng

4008522

4008528

4008586

4008588

4008589

4008014

4008016

4009102


38

38





















Attachments


Loca

tor S

elf A

ligni

ng

4008522

4008528

4008586

4008588

4008589

4008014

4008016

4009102

126.00

126.00

114.00

114.00

450.00

450.00

450.00

450.00

114.00

114.00

114.00

62.00

62.00

68.00

18.00

18.00

35.00

35.00

35.00

290.00



Combining improved design, system simplicity, and DuraTec™ Coating toughness.THE LOCATOR R-TX™ REMOVABLE ATTACHMENT SYSTEM

EASIER DENTURE SEATING WITH PIVOTING TECHNOLOGYThe magic of LOCATOR has been that the Nylon Retention Insert pivots withinthe Denture Attachment Housing, resulting in a resilient system that has allowed patients to seat their overdenture without damaging the components, even in the presence of divergence orconvergence between implants.

Patented modifications to the Denture Attachment Housingnow allow the LOCATOR R-Tx Nylon Retention Inserts topivot up to 30° to treat a maximum of 60°convergence/divergence between implants,eliminating the need for pre-angled abutments.

Legacy LOCATOR/Standard Retention

Insert

LOCATOR R-TxRetention Insert

NARROWER CORONAL GEOMETRYThe dual engaging geometry of the Abutmento�ers a narrower leading edge and taper-likee�ect to allow the patient to more easily alignand properly seat the overdenture.

EASIER DENTURE SEATING WITH PIVOTING TECHNOLOGYThe magic of LOCATOR has been that the Nylon Retention Insert pivots within the Denture Attachment Housing, resulting in a resilient system that has allowed patients to seat their overdenture without damaging the components, even in the presence of divergence or

Patented modifi cations to the Denture Attachment Housing now allow the LOCATOR R-Tx Nylon Retention Inserts to

Legacy LOCATOR/Extended RangeRetention Insert

1

1

2

2

Combining improved design, system simplicity, and DuraTec™ Coating toughness.THE LOCATOR R-TX™ REMOVABLE ATTACHMENT SYSTEM

PRACTICAL DENTURE ATTACHMENT HOUSING DESIGNHorizontal grooves and fl ats resist vertical and rotational

movement, and a channel inside the top of the Housing enhances pivot range of motion. New pink anodization

improves aesthetics in areas of thin denture acrylic.

EFFICIENT ABUTMENT/INSERT ENGAGEMENTThe Nylon Retention Inserts now engage dual retentive surfaces

on the exterior of the Abutment. No internal engagement prevents debris and plaque accumulation within the drive mechanism from

impacting proper seating of the overdenture.

NEW RETENTION INSERT DESIGN Improved design mimics the dual engagement feature of the Abutment

and resists edge deformation. Simplicity is also top of mind - the system utilizes only one set of Retention Inserts with straight forward

retention values – Zero, Low, Medium, High.

CONVENIENT ALL-IN-ONE PACKAGINGCustom designed all-in-one, double-ended vial separately

holds Abutment and Processing Components providing all necessary components for the case with one part number.

CUSTOM RETENTION INSERT TOOLDual-sided tool for easy insertion and removal ofthe LOCATOR R-Tx™ Retention Insert. Metal Slot

Feature on the back of the Tool Handle allowsthe clinician to disengage a Retention Insert

without the risk of tearing gloves.

Improved design mimics the dual engagement feature of the Abutment and resists edge deformation. Simplicity is also top of mind - the system

3

4

5

3

4

5

LOW®®®

ZERO® ® ®

HIGHMEDIUM

holds Abutment and Processing Components providing all necessary components for the case with one part number.

OUT

OUT

OUT

IN

OUT

OUT

INMetal SlotFeature

Dual SidedTool

Insert

Remove

1 . 8 0 0 . 2 6 2 . 2 3 1 0

w w w . z e s t a n c h o r s . c o m 1 of 1

IMPLANT DESCRIPTION 0.25 mm 0.5 mm 1.0 mm 2.0 mm 3.0 mm 4.0 mm 5.0 mm 6.0 mmSTRAUMANN & COMPATIBLE

Attachment System, NP Straumann Bone Level Connection 30900-01 30900-02 30900-03 30900-04 30900-05 30900-06

Attachment System, RP Straumann Bone Level Connection 30901-01 30901-02 30901-03 30901-04 30901-05 30901-06

Attachment System, RP Straumann Tissue Level Connection 31302-01 31302-02 31302-03 31302-04 31302-05 31302-06

Attachment System, 3.6mm Astra EV Connection 30700-01 30700-02 30700-03 30700-04 30700-05



Attachment System, Ankylos Conical Connection 30715-02 30715-03 30715-04 30715-05 30715-06

Attachment System, 3.4mm XiVe Connection 30711-01 30711-02 30711-03 30711-04 30711-05




Attachment System, Astra TX Connection (Aqua) 30706-01 30706-02 30706-03 30706-04 30706-05

Attachment System, Astra TX Connection (Lilac) 30707-01 30707-02 30707-03 30707-04 30707-05

Attachment System, 3.5mm Internal Hex Connection 30200-00 30200-01 30200-02 30200-03 30200-04 30200-05 30200-06


Attachment System, 3.0mm Internal Hex Connection 30600-01 30600-02 30600-03 30600-04 30600-05 30600-06


Attachment System, 4.1mm Certain Connection 30301-01 30301-02 30301-03 30301-04 30301-05 30301-06

Attachment System, 3.4mm Certain Connection 30300-01 30300-02 30300-03 30300-04 30300-05 30300-06

Attachment System, 3.4mm External Hex Connection 30305-01 30305-02 30305-03 30305-04 30305-05 30305-06

Attachment System, 4.1mm External Hex Connection 30306-01 30306-02 30306-03 30306-04 30306-05 30306-06

Attachment System, NP Tri-channel Connection 30500-00 30500-01 30500-02 30500-03 30500-04 30500-05 30500-06

Attachment System, RP Tri-channel Connection 30501-00 30501-01 30501-02 30501-03 30501-04 30501-05 30501-06

Attachment System, WP Tri-channel Connection 30502-01 30502-02 30502-03 30502-04 30502-05

Attachment System, NP Conical Connection 30506-01 30506-02 30506-03 30506-04 30506-05 30506-06

Attachment System, RP Conical Connection 30507-01 30507-02 30507-03 30507-04 30507-05 30507-06

Attachment System, NP External Hex Connection 30510-01 30510-02 30510-03 30510-04 30510-05

Attachment System, RP External Hex Connection 30511-01(1.2mm)

30511-02 30511-03 30511-04 30511-05 30511-06

Attachment System, WP External Hex Connection 30512-01(1.2mm)

30512-02 30512-03 30512-04 30512-05




NOBEL BIOCARE

R-Tx LOCATOR IMPLANT ATTACHMENT PRODUCT CODES

ZIMMER - PARAGON

ASTRA TECH / DENTSPLY

HEIGHT OF ABUTMENT TISSUE CUFF ABOVE THE IMPLANT

BIOMET (3i)

BIOHORIZON

R-Tx REMOVABLE ATTACHMENT SYSTEM

See Table R-Tx RT-x Implant Abutment & Processing Package 30001-01 R-Tx Zero Retention Insert (4) 30002-01 R-Tx Low Retention Insert (4) 30003-01 R-Tx Medium Retention Insert (4) 30004-01 R-Tx High Retention Insert (4) 30005-01 R-Tx Extra High Retention Insert (4) 30012-01 R-Tx Processing Insert (4) 30013-01 R-Tx Denture Attachment Processing Assembly (4)30014-01 R-Tx 3.35mm Abutment Analog (4) 30015-01 R-Tx 4mm Abutment Analog (4) 30016-01 R-Tx 5mm Abutment Analog (4) 30017-01 R-Tx Impression Coping (4) 30018-01 R-Tx Processing Spacer (4) 30021-01 R-Tx Retention Insert Tool


47


47

The Locator R-Tx™ Removable Attachment System is available now at PREAT, backed by expert support from our highly trained technicians and ICOI Masters.

Your Patients Deserve the Best. And So Do You.

The industry standard

for overdenture

solutions is now even

better—get it first

at PREAT.

Order today at 800.232.7732 or online at PREAT.com.

Introducing the brand new Locator R-Tx™ Removable Attachment System.

• Increased Pivoting with

Angle Correction Up to

30° Per Attachment: Easier

seating that eliminates the

need for angled abutments

and reduces damage during

patient insertion and removal.

• Improved Abutment Wear

Resistance: 32% harder, 26%

more wear resistance, 64%

reduction in roughness, and an

esthetic gingiva color.

• More Esthetic and Functional

Attachment Housings: Pink

with grooves and flats for

improved retention in acrylic,

improving esthetics and

patient confidence.

2.73mm vertical, 5.45mm Ø The R-Tx attachment system corrects up to 60° of implant divergence, provides an easy self-aligning path of insertion, utilized esthetic pink housings, and new Duratec abutment coating for longer life and greater wear resistance. 2.85mm vertical, 5.55mm Ø

R-Tx Zero Retention Insert (4-Pack)30001-01 23.00

R-Tx Low Retention Insert (4-Pack)30002-01 23.00

R-Tx Medium Retention Insert (4-Pack)30003-01 23.00

R-Tx High Retention Insert (4-Pack)30004-01 23.00

R-Tx Processing Insert (4-Pack)30012-01 23.00

R-Tx Denture Attachment Processing Assembly (4-Pack)30013-01 56.00

R-Tx 3.35mm Abutment Analog (4-Pack)30014-01 68.00

R-Tx analogs for use with narrow diameter implants

R-Tx 4mm Abutment Analog (4-Pack)30015-01 68.50

R-Tx analogs for use with regular platform implants


R-Tx analogs for use with wide diameter implants

R-Tx Impression Coping (4-Pack)30017-01 68.50

R-Tx Processing Spacer (4-Pack)30018-01 31.00

R-Tx Retention Insert Tool30021-01 55.00

LOCATOR Block Out Spacer (20-Pack)4008514 23.00

Attachments

IMPLANT ABUTMENTS/ATTACHMENTSLocator RT-x

Locator R-Tx

30003-01

30004-01

30013-01

30015-01

30017-01

30021-01

30001-01

75.00

75.00

75.00

47


47




for overdenture



at PREAT.




















patient confidence.


















Attachments

IMPLANT ABUTMENTS/ATTACHMENTSLocator RT-x

Locator R-Tx

30003-01

30004-01

30013-01

30015-01

30017-01

30021-01

30001-01

28.00

28.00

28.00

28.00

28.00

68.00

80.00

80.00

80.00

80.00

40.00

65.00

28.00

BIO-Torq Tips & Drivers

are fully compatible with

ITL Torque Wrench

* All tips sold separately,available in short and long. Please call for pricing.

The Fully Adjustable

ITL Precision Torque Wrench

Features

CE Mark

Autoclavable

No Lubrication

Ratchet Mechanism

9 Torque Settings

15, 20, 25, 30, 35, 40

45, 50 and 60 Ncm

Order No. 44-ATW

44-HTLT

BIO-TORQ Tip Hex .050”, Short Aii, Calcitek, Paragon, Steri-Oss .050” hex screws

44-HTT

BIO-TORQ Tip Hex .050”, Long

44-HNT

BIO-TORQ Tip Hex .048”, Short Branemark, Lifecore, 3i .048” hex screws

44-HNLT


44-ITIL

BIO-TORQ Tip SCS ITI Straumann, Long Straumann SCS ITI

44-PROCS

BIO-TORQ Tip Torx UniGrip (star), Short Nobel Biocare UniGrip

44-PROCL

BIO-TORQ Tip Torx UniGrip (star), Long

59-100180

BIO-TORQ Tip Square .050” Cera1, Short Cera 1, Nobel Biocare & 3i square screws

59-100181

BIO-TORQ Tip Square .050” Cera1, Long

Order No.

8926

BIO-TORQ Tip Square (locator driver) , Short

8927

BIO-TORQ Tip Square (locator driver) , Long

44-ITIS

BIO-TORQ Tip SCS ITI Straumann, Short Straumann SCS ITI

We Carry A W

ide

Array Of Tips Compatible

With Virtually All Screw

s &

Implant Com

ponents

CM Universal Torque W

rench

Latch Tips & Drivers are fully compatible with Universal Torque W

rench

T5415

Latch Tip .050 ”Hex, Short

T5405


8913

Latch Tip Locator, Short

T5435

Latch Tip Uni-Torx, Short

T5410 Latch Tip .050 ”Hex, Long


8914 Latch Tip Locator, Long

T5430 Latch Tip Uni-Torx, Long

T5445 Latch Tip SCS, Short

T5440 Latch Tip SCS, Long

Order No.

Implant Lab Screwdrivers

Dura Pattern LC

- E�cient m

odeling gel.

Implant Lab Screwdrivers from

Diamodent

ful�ll your lab’s needs when doing implant

work. No more searching for sm

all implant

drivers’. These larger screwdrivers have an

ergonomic handle with an e�

cient rotating

tip for easy turning. They are available in a

variety of colour-coded types: .050” Hex, .048”

Hex, Square, Unigrip®, SCS®. There is also a

unique screwdriver holder that will rest on a

bench or mount to a wall.

• One-component light cure resin

• Easy modeling gel for im

plant jigs

• Replaces wax for copings

• Burns out clean and residue free

• No distortion, easy to grind on

• Zero shrinkage

33-T5590

Implant Lab ScrewDriver Kit

33-T5500

Implant .048" Hex Lab ScrewDriver

33-T5510

Implant .050" Hex, Long Lab ScrewDriver

33-T5520

Implant Square Lab ScrewDriver

33-T5530

Implant UniGrip Lab ScrewDriver

33-T5540

Implant SCS Lab ScrewDriver

33-T5550

Implant Slotted Lab ScrewDriver

33-T5580

Implant Lab ScrewDriver Holder

3000 - DuraPattern LC Flow, Blue 3x3 g DuraPattern LC Flow

3002 - DuraPattern LC Paste, Blue 30 g DuraPattern LC Paste

This torque wrench is a universal dental

instrument that provides a m

eans of

tightening and loosening screws,

prosthesis elements and im

plants.



ITL Torque Wrench




Features

CE Mark

Autoclavable

No Lubrication

Ratchet Mechanism

9 Torque Settings

15, 20, 25, 30, 35, 40

45, 50 and 60 Ncm

Order No. 44-ATW

44-HTLT


44-HTT


44-HNT


44-HNLT


44-ITIL


44-PROCS


44-PROCL


59-100180


59-100181

BIO-TORQ Tip Square .050” Cera1, Long Order No.

8926


8927


44-ITIS


We Carry A W

ide


With Virtually All Screws &

Implant Com

ponents


rench


rench

T5415


T5405


8913


T5435








Order No.


Dura Pattern LC

- E�cient m

odeling gel.


Diamodent



all implant



cient rotating








plant jigs




• Zero shrinkage

33-T5590


33-T5500


33-T5510


33-T5520


33-T5530


33-T5540


33-T5550


33-T5580






eans of



plants.

44-HTLT

T5415

44-HTT47


47




for overdenture



at PREAT.




















patient confidence.


















Attachments


Locator RT-x

Locator R-Tx

30003-01

30004-01

30013-01

30015-01

30017-01

30021-01

30001-01

BioTORQ Tip Hex .050”, Short (25mm)

Latch Tip .050” Hex, Short (25mm)

BioTORQ Tip Hex .050”, Long (30mm)

75.00T5410 Latch Tip .050” Hex, Long (30mm)

T5415

44-HTLT

180.00See Table (Left) R-Tx Abutment (Includes Male Processing Pack)


47


47




for overdenture



at PREAT.




















patient confidence.


















Attachments


Locator RT-x

Locator R-Tx

30003-01

30004-01

30013-01

30015-01

30017-01

30021-01

30001-01



17

17

Direct Placement 2.5mm “double sphere” self-paralleling attachment 3.40mm tall, 3.55mm Ø tooth surface 4.10mm Ø housing

Sphero Flex Post Starter Kit (6-Pack)0800500 580.00

2 6.5mm Posts, 2 7.5mm Posts, 2 9.0mm posts, 2 drills, insertion tool

Sphero Flex Post Short 6.50mm0800510 120.00

Sphero Flex Post Medium 7.50mm0800512 120.00

Sphero Flex Post Long 9.00mm0800514 120.00

Sphero Flex Post Reamer Yellow (6.5 and 7.5mm)0800540 37.00

Sphero Flex Post Reamer Blue (7.5 and 9.0mm)0800542 37.00

2.5mm Retention Caps--Pink (6)0800162 48.00

Standard- 1.65lbs

2.5mm Retention Caps--Green (6)0800163 48.00

soft, gummy for patient comfort

2.5mm Retention Caps--Yellow (6)0800164 48.00

Soft- 1.21lbs

2.5mm Retention Caps--White (6)0800166 48.00

Strong- 2.87lbs

2.5mm Retention Caps--Orange(6)0800167 48.00

for worn spheres, Elastic Retention (2.2mm)

2.5mm Retention Caps--Light Green (6)0800161 48.00

for worn spheres, Rigid Retention (2.2mm)

Sphero Flex Post System

Attachments

OVERDENTURE STUD

Sphero Post

0800161

0800167

0800166

0800164

0800163

0800162

0800500

77.00

77.00

77.00

77.00

77.00

77.00

8-040CRNSN

8-049PCN

8-060CRNAY

8-040CRN

8-049PCNDR8

8-040CRNDR8


17

17

Direct Placement 2.5mm “double sphere” self-paralleling attachment 3.40mm tall, 3.55mm Ø tooth surface 4.10mm Ø housing

Sphero Flex Post Starter Kit (6-Pack)0800500 580.00

2 6.5mm Posts, 2 7.5mm Posts, 2 9.0mm posts, 2 drills, insertion tool

Sphero Flex Post Short 6.50mm0800510 120.00

Sphero Flex Post Medium 7.50mm0800512 120.00

Sphero Flex Post Long 9.00mm0800514 120.00

Sphero Flex Post Reamer Yellow (6.5 and 7.5mm)0800540 37.00

Sphero Flex Post Reamer Blue (7.5 and 9.0mm)0800542 37.00

2.5mm Retention Caps--Pink (6)0800162 48.00

Standard- 1.65lbs

2.5mm Retention Caps--Green (6)0800163 48.00

soft, gummy for patient comfort

2.5mm Retention Caps--Yellow (6)0800164 48.00

Soft- 1.21lbs

2.5mm Retention Caps--White (6)0800166 48.00

Strong- 2.87lbs

2.5mm Retention Caps--Orange(6)0800167 48.00

for worn spheres, Elastic Retention (2.2mm)

2.5mm Retention Caps--Light Green (6)0800161 48.00

for worn spheres, Rigid Retention (2.2mm)

Sphero Flex Post System

Attachments

OVERDENTURE STUD

Sphero Post

0800161

0800167

0800166

0800164

0800163

0800162

0800500

77.00

52.00

52.00

62.00

62.00

77.00

77.00

77.00

77.00

77.00

47.00

77.00

8-040CRMSN

8-044PPN

8-044PPM

8-041CAN

8-041CAMB

8-040CRM

8-049PCM

8-040CRMDR8

8-060CRMAY

8-049MCMDR8

8-043CLM

8-048CAM

1.8mm Retention Caps--Pink (6) Micro (Soft Retention)

2 Normal Transfer Pivots (Analogs)

2 Normal Micro Transfer Pivots (Analogs)

2 Stainless Steel Housings (For Resin)

2 Stainless Steel Micro Housings (For Resin)

1.8mm Retention Caps--Clear (6) Micro (Standard Retention)

1.8mm Retention Caps--Green (6) Micro (Very Elastic Retention)

1.8mm Retention Caps--Aqua (6) Micro (Strong Retention)

1.8mm Retention Caps--Yellow (6) Micro (Extra Soft Retention)

1.8mm Retention Caps--Orange (6) Micro (Very Elastic Retention)

1.8mm Processing Caps--Black (6) Micro (Lab Use Only)

1.8mm Retention Caps--Silver (6) Micro (Extra Resiliant Soft)

8-049PCN

8-060CRNAY

8-040CRNSN

8-049PCNDR8

8-040CRNDR8

8-044PPN

8-041CANB


16

16


















O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



OVERDENTURE STUD OT CAP RHEIN83


52.00

58.00

62.00

52.00

58.00

52.00

58.00

52.00

52.00

58.00

50.00

62.00

79.00

68.00

64.00

8-140CEV

8-045CSM AY

8-192ECE

8-140CEG

8-045CSMDR8

8-140CET

8-045CSM SN

8-140CEN

8-140CER

8-045CSM

8-140CAE

8-046CSM

8-044PPS

8-144MTE

8-144AE

4 Retentive Caps - Violet (Strong)

4 Strategy Yellow Caps for Stainless Steel Housing (Extra Soft)

Caps Assortment Kit (Male Complete) Kit Contains:1 Stainless steel housing, 1 processing cap, 4 Retentive caps.

4 Retentive Caps - Yellow (Extra Soft)

4 Strategy Aqua Caps for Stainless Steel Housing (Extra Strong)

4 Retentive Caps - White (Standard)

4 Strategy Pink Caps for Stainless Steel Housing (Soft)

4 Processing Caps - Black (For Lab)

4 Retentive Caps - Pink (Soft)

4 Strategy White Caps for Stainless Steel Housing (Standard)

2 Stainless Steel Housings

2 Strategy Stainless Steel Housings

2 Strategy Transfer Pivots (Analogs)

2 Impression Coping

2 Laboratory Analog

8-144MTE

8-144AE

8-045CSM AY

8-045CSM SN

8-046CSM

8-140CAE

8-140CEV


16

16


















O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025




16

16


















O-R

ing

Atta

chm

ent

Attachments

OVERDENTURE STUD

1500154

O-Ring

1500534

1500502

1500503

1500504

1500506

1600025



OVERDENTURE STUD

OT STRATEGY

EQUATOR RHEIN83

RHEIN 83



99

99

Implants

MULTI-UNIT COMPONENTS

Multi-U

nit

Prosthetics based upon Nobel Biocare

Clix Complete Ball Abutment for Multi-Unit x 2mm1603702* 110.00

O-Ring Ball Abutment Multi-Unit x 2mm1703702* 110.00


Multi-Unit Analog8003700 16.00

Multi-Unit Analog (10-Pack)8003700-10 140.00

Multi-Unit Open Tray Impression Coping8003701 28.00

Multi-Unit Closed Tray Impression Coping8003702 28.00

Multi-Unit Non-Engaging Verification Cylinder8003730 38.00

Multi-Unit Non-Engaging Verification Cylinder8003730-10 340.00

Multi-Unit Titanium Screw (Unigrip)8003750 16.00

Multi-Unit Titanium Screw (Unigrip) (10-Pack)8003750-10 130.00

Multi-Unit Titanium Screw (.050 Hex)8003751 16.00

Multi-Unit Titanium Screw (.050 Hex) (10-Pack)8003751-10 130.00

Multi-Unit Guide Pin 20mm8003753 16.00

Multi-Unit Non-Engaging Titanium Base8003760 50.00

Multi-Unit PAC Titanium Screw9003755 30.00

Multi-Unit Driver8003705 40.00

Multi-Unit Gold/Plastic Coping8003720 115.00

8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon

Multi-Unit Gold Bar Coping8003725 115.00


99

99

Implants


Multi-U

nit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon



99

99

Implants


Multi-U

nit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon



99

99

Implants

MULTI-UNIT COMPONENTSM

ulti-Unit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


8909-2

70-1074-PRS0016

290.00

20.00


99

99

Implants


ulti-Unit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


70-1074-PRS0052

70-1074-PRS0021

70-1074-PRS0057

40.00

35.00

40.00


99

99

Implants


ulti-Unit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


70-1072-PRC0043 22.00


99

99

Implants


Multi-U

nit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


70-1072-PRC0014 22.00


99

99

Implants


Multi-U

nitProsthetics based upon Nobel Biocare



















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


70-1074-PRS0019

70-1074-PRS0048

20.00

55.00


99

99

Implants


Multi-U

nitProsthetics based upon Nobel Biocare



















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


70-1074-PRS0028

70-1074-PRS0030

70-1074-PRS0018

65.00

135.00

135.00

135.00See Web Multi-Unit Abutments / Compatible With:BioHorizon® / Zimmer Dental Screw-Vent®, DENTSPLY Implants ASTRA TECH, Implant System®, Nobel Biocare Brånemark System®,Nobel Biocare NobelActive®, Nobel Biocare NobelReplace®,Straumann® Bone Level. (Available In Straight, 170 And 300 Cuff Heights Ranging From 1Mm To 5mm).

Multi-Unit Abutment

MULTI-UNIT COMPONENTS IMPLANTS

Dynamic TiBase® Compatibilities

CA

D-C

AM

SO

LUT

ION

S

CAD-CAMSOLUTIONS


99

99

Implants


ulti-Unit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon


85.00

85.00

31.323.025.01-2

31.323.008.01-2

Nobel Multi-Unit Non-Engaging Tibase With 300 Angle Correction

Astra Uni-Abutment Non-Engaging Tibase With 300 Angle Correction

31.323.025.01-2

Compatible with - MISLance - MIS

Seven / M4 - MIS

Hex. h.

RP 2,70 0,70

C1 - MIS

Multi-Unit - MIS

V3 - MIS

ST Titanium IND3UCS41/TiA IND3UCH41/TiA TPDH2L6 TBRA2L70 SBIND3RP/PK RUC41 DAS_E_0024

Non-Engaging EngagingDynamic screw

Straight screw Library codeScanbody Analog

NP Titanium IND3MM4RNP/TiA IND3MM4HNP/TiA TPDH16L71 --- SBIND3NP/PK --- DAS_E_0019

ST Titanium IND3ZIMR35/TiA IND3ZIMH35/TiA TPDH17L71 TZIML76 SBIND3NP/PK RZIM35 DAS_E_0040

WP Titanium IND3ZIMR45/TiA IND3ZIMH45/TiA TPDH17L71 TZIML76 SBIND3RP/PK RZIM45 DAS_E_0041

NP Titanium IND3MC1RNP/TiA IND3MC1HNP/TiA TPDH16L71 --- SBIND3NP/PK --- DAS_E_0016

RP Titanium IND3MC1RRP/TiA IND3MC1HRP/TiA TPDH17L73 --- SBIND3RP/PK --- DAS_E_0017

WP Titanium IND3MC1RWP/TiA IND3MC1HWP/TiA TPDH17L73 --- SBIND3RP/PK --- DAS_E_0018

ST Titanium IND3MC1RRP/TiA IND3MC1HRP/TiA TPDH17L73 --- SBIND3RP/PK --- DAS_E_0017

GENERAL Titanium IND3MMU/TiA -- TPDH16 --- SBIND3MURP/PK --- DAS_E_0020

Platform Material

Compatible with - NOBEL BIOCARE

Branemark - NOBEL BIOCARE

Hex. h.

NP 2,40 0,70

RP 2,70 0,70

NP Titanium IND3UCS35/TiA IND3UCH35/TiA TPDH16L6 TBRA16L70 SBIND3NP/PK RUC35 DAS_E_0023

RP Titanium IND3UCS41/TiA IND3UCH41/TiA TPDH2L6 TBRA2L70 SBIND3RP/PK RUC41 DAS_E_0024


Straight screw Library codeScanbody AnalogPlatform Material

Multi-Unit - NOBEL BIOCARE

RP Titanium IND3CO41/TiA --- TPDH14L39 TMU14L35 SBIND3MURP/PK RMU48 DAS_E_0025


Straight screw Library codeScanbody AnalogPlatform Material

Compatible with - HIOSSEN IMPLANT

US - HIOSSEN

Hex. h.

NP 2,40 0,70

RP 2,70 0,70

TS - HIOSSEN

*Maximum angulation 20º

MINI* Titanium IND3OTSRNP/TiA IND3OTSHNP/TiA TPDH16L94 TCAM16L105 SBIND3NP/PK --- DAS_E_0029

RP Titanium IND3OTSRRP/TiA IND3OTSHRP/TiA TPDH2L79 --- SBIND3RP/PK --- DAS_E_0030


Straight screw Library codeScanbody Analog

MINIØ 3,5

Titanium IND3UCS35/TiA IND3UCH35/TiA TPDH16L6 TBRA16L70 SBIND3NP/PK RUC35 DAS_E_0023

RPØ 4,1 Titanium IND3UCS41/TiA IND3UCH41/TiA TPDH2L6 TBRA2L70 SBIND3RP/PK RUC41 DAS_E_0024

Platform Material


99

99

Implants


Multi-U

nit




















8003720

8003705

8003760

8003750

8003730

8003701

8003700

4008909

*Available soon



LOCATOR F-Tx Abutment Driver, Manual

(Used with square drive connections)

LOCATOR F-Tx Abutment Driver, Latch

(Used with latch-lock connections)

LOCATOR F-Tx Retention Ball Hex Driver

10028

10029

10042

1.5mm 2mm 3mm 4mm 5mm 6mm

F-Tx Attachment System, 3.4mm Certain Connection 10300-01 10300-02 10300-03 10300-04 10300-05 10300-06

F-Tx Attachment System, 4.1mm Certain Connection 10301-01 10301-02 10301-03 10301-04 10301-05 10301-06

F-Tx Attachment System, 4.1mm External Hex Connection 10301-01 10301-02 10301-03 10301-04 10301-05 10301-06

F-Tx Attachment System, 3.5mm Internal Hex Connection 10200-01 10200-02 10200-03 10200-04 10200-05 10200-06

F-Tx Attachment System, 4.5mm Internal Hex Connection 10201-01 10201-02 10201-03 10201-04 10201-05 10201-06

F-Tx Attachment System, Narrow Platform (NP) Tri-channel Connection 10500-01 10500-02 10500-03 10500-04 10500-05 10500-06

F-Tx Attachment System, Regular Platform (RP) Tri-channel Connection 10501-01 10501-02 10501-03 10501-04 10501-05 10501-06

F-Tx Attachment System, Narrow Platform (NP) Conical Connection 10506-01 10506-02 10506-03 10506-04 10506-05 10506-06

F-Tx Attachment System, Regular Platform (RP) Conical Connection 10507-01 10507-02 10507-03 10507-04 10507-05 10507-06

F-Tx Attachment System, Wide Platform (WP) Conical Connection 10508-01 10508-02 10508-03 10508-04 10508-05 10508-06

F-Tx Attachment System, Narrow Platform (NP) External Hex Connection 10510-02 10510-03 10510-04 10510-05 10510-06

F-Tx Attachment System, Regular Platform (RP) External Hex Connection 10511-02 10511-03 10511-04 10511-05 10511-06

F-Tx Attachment System, Ankylos Connection 10715-02 10715-03 10715-04 10715-05 10715-06

HEIGHT OF ABUTMENT TISSUE CUFF ABOVE THE IMPLANTIMPLANT DESCRIPTION

Biomet 3i

Nobel Biocare Conical Connection

Nobel Biocare Branemark / 3i External

Dentsply

Bio Horizons / Zimmer Biomet

Nobel Biocare Replace Select

Locator F-Tx Abutments (Implants)

F-Tx Attachment System, 3.6mm Astra EV Connection 10700-01 10700-02 10700-03 10700-04 10700-05 10700-06



Astra TX (ACQUA) 10706-1 10706-2 10706-3 10706-4 10706-5 10706-6

Astra TX (LILAC) 10707-1 10707-2 10707-3 10707-4 10707-5 10707-6

F-Tx Attachment System, Narrow Platform (NP) Bone Level Connection 10900-01 10900-02 10900-03 10900-04 10900-05 10900-06

F-Tx Attachment System, Regular Platform (RP) Bone Level Connection 10901-01 10901-02 10901-03 10901-04 10901-05 10901-06

F-Tx Attachment System, Regular Platform (RP) Tissue Level Connection 10906-02 10906-03 10906-04 10906-05 10906-06

Straumann

1

PACKAGED WITH:

• Abutment• Denture Attachment Housing

with pre-inserted Processing Ball• Extra Processing Ball (Black)• Low Retention Ball (Blue)• Medium Retention Ball (Tan)• High Retention Ball (Green)• Block-Out Spacer (2x)

LOCATOR F-Tx™ COMPONENTS REFERENCE

RETENTION BALLS

HEALING CAP TOOLS

QTY 2 QTY 2QTY 2

Low Retention Ball (5 Lbs)10033

Medium Retention Ball(10 Lbs)10034

High Retention Ball (20 Lbs)10035

LAB PROCESSING

QTY 2

Abutment Analog10037

QTY 2

Processing Ball10032

QTY 2

Processing Cap10030

QTY 2

Waxing Cap10040

QTY 2

Abutment Driver10028 - Manual

Retention Ball Driver10042

QTY 20

Block-Out Spacer08514

Processing Ball

Medium Retention

Ball

Low Retention

Ball

High Retention

Ball

Denture Attachment

HousingAbutment Block-Out

Spacer

Healing Cap 10036

LOCATOR F-Tx ATTACHMENT SYSTEM

QTY 2

Polishing Cap10039

Denture Attachment Housing10041

Impression Coping10043

QTY 2

LOCATOR F-Tx PROSTHESIS REMOVAL SYSTEM

BOOSTER CUSHIONS

10080

INFLATION DEVICE

10044

2 x 8mm

1 x 10mmOption 1

2 x 6mm

1 x 8mmOption 2

10045

LOCATOR F-Tx PROSTHESIS BOOSTER

10029 - Latch

1

PACKAGED WITH:




RETENTION BALLS

HEALING CAP TOOLS

QTY 2 QTY 2QTY 2




LAB PROCESSING

QTY 2


QTY 2


QTY 2

Processing Cap10030

QTY 2

Waxing Cap10040

QTY 2



QTY 20


Processing Ball

Medium Retention

Ball

Low Retention

Ball

High Retention

Ball

Denture Attachment


Spacer

Healing Cap 10036


QTY 2

Polishing Cap10039



QTY 2


BOOSTER CUSHIONS

10080

INFLATION DEVICE

10044

2 x 8mm

1 x 10mmOption 1

2 x 6mm

1 x 8mmOption 2

10045


10029 - Latch

1

PACKAGED WITH:




RETENTION BALLS

HEALING CAP TOOLS

QTY 2 QTY 2QTY 2




LAB PROCESSING

QTY 2


QTY 2


QTY 2

Processing Cap10030

QTY 2

Waxing Cap10040

QTY 2



QTY 20


Processing Ball

Medium Retention

Ball

Low Retention

Ball

High Retention

Ball

Denture Attachment


Spacer

Healing Cap 10036


QTY 2

Polishing Cap10039



QTY 2


BOOSTER CUSHIONS

10080

INFLATION DEVICE

10044

2 x 8mm

1 x 10mmOption 1

2 x 6mm

1 x 8mmOption 2

10045


10029 - Latch

DRIVERS

LOCATOR F-Tx™ FIXED ATTACHMENT SYSTEM

Each LOCATOR F-Tx Abutment is delivered in convenient all-in-one packaging that includes all the sterile components needed for each implant.

Order for your favorite implant systems using this product ordering and reference guide.

SELECTING THE PROPER CUFF HEIGHT FOR THE LOCATOR F-Tx ABUTMENT

1. Using a periodontal probe, measure from the top of the implant to the highest point of the gingiva.

2. The cuff size should match the tissue height, as this will place the prosthetic finish line right at the gingival height and maximizes the retention surface of the Denture Attachment Housing in the prosthesis. The cuff margin is at the widest portion of the sphere (midpoint of the Abutment sphere). For subgingival finish line, choose a shorter cuff size.

1 2

LOCATOR F-Tx Abutment

Denture Attachment Housing

with pre-inserted Processing Ball

Low (Blue)Retention Ball

BlackProcessing Ball

Medium (Tan)Retention Ball

High (Green)Retention Ball

Block-outSpacer

1 - Abutment1 - Denture Attachment Housing with

Pre-inserted Processing Ball1 - Low (Blue) Retention Ball1 - Medium (Tan) Retention Ball1 - High (Green) Retention Ball1 - Additional Processing Ball2 - Block-Out Spacer (Packaged separately)

249PRICE INCLUDES:$







1 2








Block-outSpacer



249PRICE INCLUDES:$







1 2








Block-outSpacer



249PRICE INCLUDES:$







1 2








Block-outSpacer



249PRICE INCLUDES:$

PART # DESCRIPTION PRICE

PROCESSING COMPONENTS

10041 Denture Attachment Housing (Qty. 2) $80.00

10032 Black Processing Ball (Qty. 2) $35.00

10033 Low Retention Ball (Blue), (Qty. 2) $35.00

10034 Medium Retention Ball (Tan), (Qty. 2) $35.00

10035 High Retention Ball (Green), (Qty. 2) $35.00

10036 Healing Cap (Qty. 2) $40.00

10037 Abutment Analog (Qty. 2) $40.00

10040 Waxing Cap (Qty. 2) $40.00

10043 Impression Coping (Qty. 2) $80.00

10030 Processing Cap (Qty. 2) $40.00

10039 Polishing Cap (Qty. 2) $40.00

LOCATOR F-Tx™ FIXED ATTACHMENT SYSTEMAncillary Components

$80.00

$35.00

$35.00

$35.00

$35.00

E.+O.E. Sales 169Prices are subject to change without notice

$305

4 US Retail Price List | January 1, 2017

IMPLANT ATTACHMENT SYSTEM - FIXED

LOCATOR F-Tx® - FIXED ATTACHMENT SYSTEM

EACH ALL-IN-ONE LOCATOR F-Tx ABUTMENT SYSTEM IS PACKAGED STERILE WITH: (1) F-Tx Abutment, (1) Denture Attachment Housing (with pre-inserted Processing Ball),

(1) Low Retention Ball, (1) Medium Retention Ball, (1) High Retention Ball, (1) Additional Processing Ball, (2) Block-Out Spacers (packaged separately)

NOTE: For current LOCATOR F-Tx Implant Attachment Part Numbers, please visit www.zestdent.com

LOCATOR F-Tx PEEK RETENTION BALLS:

LOCATOR F-Tx PROCESSING COMPONENTS

PART# DESCRIPTION PRICE

10041 Denture Attachment Housing - 2 Pack $80.00

10032 Black: Processing Ball - 2 Pack $35.00

10033 Blue: Low Retention Ball - 2 Pack $35.00

10034 Tan: Medium Retention Ball - 2 Pack $35.00

10035 Green: High Retention Ball - 2 Pack $35.00

10036 Healing Cap - 2 Pack $40.00

10037 Abutment Analog - 2 Pack $40.00

10040 Waxing Cap - 2 Pack $40.00

10043 Impression Coping - 2 Pack $80.00

08514 Block Out Spacer - 20 Pack $18.00

10030 Processing Cap - 2 Pack $40.00

10039 Polishing Cap - 2 Pack $40.00





- ABUTMENTS


4 US Retail Price List | January 1, 2017

























$90.00

$42.00

$42.00

$47.00

$90.00

$48.00

$42.00

$42.00

$47.00

$47.00

$30.00

$48.004 US Retail Price List | January 1, 2017

























5www.zestdent.com | Phone: 1-800-262-2310 or Fax: 1-800-487-1357

LOCATOR F-Tx TOOLS


10028 Abutment Driver, Manual (Square Drive Connection) $55.00

10029 Abutment Driver, Latch (Latch-lock Connection) $55.00

10042 Retention Ball Hex Driver $55.00

10080 Inflation Device $99.00

10045 Prosthesis Booster Set (10mm | 8mm | 8mm) $49.99

10024 Removal Tool Bar $99.00

10023 Removal Loop $30.00

$62.00

$62.00

$56.00

$34.00

$62.00

$120.00

$110.00

10111 New! Locator R-Tx Seating and Removal Tool



92


92

92

Attachments

REMOVABLE PROSTHETIC SPECIALTY

Perm

a Re

t

Perma Ret is a simple solution for Permanent Retention of acrylic and composite denture teeth in both full and partial dentures. Simply drill a small hole in the tooth with the provided twist drill. Cut a length of silver wire and insert in the wire holder. Thread the wire into the tooth. Bend the wire into desired position. Then process the denture base material.

Perma Ret Kit0109000 172.00

3 twist drills, 1 wire holder, and 13 pieces of 80mm long threaded silver wire

Perma Ret Wire Refill0109002 140.00

13 pieces of 80mm long threaded silver wire

Perma Ret Wire Refill (6-Pack)0109002-6 720.00

Perma Ret Twist Drills (3)0109004 28.00

Perma Ret Tool0109006 34.00

Denture Stippling Mandrel6000005 45.00

The 1/4 inch shaft will fit most standard chucks on a dental lathe. The user should place 4 of either a

#2, #4, or #6 round straight handpiece or FG steel or carbide burs into the stippling mandrel and tighten securely with

the Allen wrench that is included with the stippling mandrel. Best results are achieved using dull or used burs.

*Burs are not included with the mandrel*

Gingivamoll is a soft, flexible, silicone rubber removable gingival mask that esthetically replaces lost tissue and provides increased thermal comfort. This removable prosthesis is produced from surgical grade silicone rubber. The mask is very thin, fits comfortably, and is virtually undetectable in the mouth, blending with vital tissue.

Gingivamoll Starter Kit0900001 310.00

Opaque material 4g, pink material 2.5g, stain 4g, light pink material 2.5g,

stain liquid 5ml, red and blue dye, protective lacquer 5ml.

Gingivamoll Light Pink 5g0906402 149.00

Ging

ivam

oll

Perma Ret

0109000

Perma Ret

Perma Ret

6000005

Gingivamoll

Gingivamoll

Gingivamoll


92


92

92

Attachments


Perm

a Re

t



















Ging

ivam

oll

Perma Ret

0109000

Perma Ret

Perma Ret

6000005

Gingivamoll

Gingivamoll

Gingivamoll


92


92

92

Attachments


Perm

a Re

t



















Ging

ivam

oll

Perma Ret

0109000

Perma Ret

Perma Ret

6000005

Gingivamoll

Gingivamoll

Gingivamoll

175.00

147.00

30.00

1601

1602

1606


87

87

Attachments

FIBER TECHNOLOGY

eFiber

eFiber (unidirectional) and Mesh (multi-directional) are BisGMA and PMMA impregnated E-glass fibers. Use fiber to prevent Stress Cracks from starting before they begin. Increase fatigue resistance. Increase flexural strength. Improve Esthetics--the fibers are translucent; no ugly metal wires. Happy patients--eliminate broken prostheses and non-revenue chairside time. Easy to grind and finish-stop breakage before it begins. Bonds to all composite and acrylic resins. Easy to handle; no special tools needed--Improve productivity

eFiber Starter Kit7009050 325.00

45cm of Perma Mesh, 10cm eFiber 1.6mm, 10cm eFiber 1.2mm, Bonding Adhesive (white bottle), Wetting Agent (black bottle),

Flowable Composite with extra tips, Goats Hair Polishing Wheel, 244 Blue Polishing Paste, F8 Silicone Cutter/Polisher

The Dentist’s Must Have Toolbox!

eFiber Perio Kit7009052 160.00

(2) 10cm units of eFiber 1.2mm, (1) silicone tool, an instructional DVD, and user instructions.

eFiber Ortho Kit7009055 165.00

(2) 10cm units of eFiber 1.2mm, (1) 2mL syringe of flowable composite, (1) silicone tool, an instructional DVD, and user instructions.

eFiber 1.2mm7009060 92.00

10 cm long narrow diameter translucent polishable e-glass fiber for direct bonded ortho and perio splints

eFiber 1.2mm (2 units)7009060-2 170.00

eFiber 1.2mm (3 units)7009060-3 225.00

eFiber 1.2mm (5 units)7009060-5 350.00

eFiber 1.2mm(10 units)7009060-10 575.00

eFiber 1.6mm7009070 92.00

10 cm long wider diameter translucent polishable e-glass fiber for reinforced dentures, repairs, maryland bridges, and more!

7009070

7009060

Space Maintainer

Fiber Maryland

Fiber Ortho

7009050

Fiber Denture

Fiber Splint

525.00

REMOVABLE PROSTHETIC ATTACHMENTS

120.00

300.00

120.00

300.00

345.00

90.00

301040

301045

301010

301045

301555

FP300016

Shera Duett-Soft Silicone Putty (2 x 1.5Kg) Shore 85

Shera Duett-Soft Silicone Putty (2 x 5Kg) Shore 85

Shera Duett Silicone Putty (2 x 1.5Kg) Shore 90

Shera Duett Silicone Putty (2 x 5Kg) Shore 90

Shera Duett-Super Soft Silicone Putty (2 x 4Kg) Shore 50

Teeth Clean


92


92

92

Attachments


Perm

a Re

t



















Ging

ivam

oll

Perma Ret

0109000

Perma Ret

Perma Ret

6000005

Gingivamoll

Gingivamoll

Gingivamoll


87

87

Attachments

FIBER TECHNOLOGY

eFiber

eFiber (unidirectional) and Mesh (multi-directional) are BisGMA and PMMA impregnated E-glass fibers. Use fiber to prevent Stress Cracks from starting before they begin. Increase fatigue resistance. Increase flexural strength. Improve Esthetics--the fibers are translucent; no ugly metal wires. Happy patients--eliminate broken prostheses and non-revenue chairside time. Easy to grind and finish-stop breakage before it begins. Bonds to all composite and acrylic resins. Easy to handle; no special tools needed--Improve productivity

eFiber Starter Kit7009050 325.00

45cm of Perma Mesh, 10cm eFiber 1.6mm, 10cm eFiber 1.2mm, Bonding Adhesive (white bottle), Wetting Agent (black bottle),

Flowable Composite with extra tips, Goats Hair Polishing Wheel, 244 Blue Polishing Paste, F8 Silicone Cutter/Polisher

The Dentist’s Must Have Toolbox!

eFiber Perio Kit7009052 160.00

(2) 10cm units of eFiber 1.2mm, (1) silicone tool, an instructional DVD, and user instructions.

eFiber Ortho Kit7009055 165.00

(2) 10cm units of eFiber 1.2mm, (1) 2mL syringe of flowable composite, (1) silicone tool, an instructional DVD, and user instructions.

eFiber 1.2mm7009060 92.00

10 cm long narrow diameter translucent polishable e-glass fiber for direct bonded ortho and perio splints

eFiber 1.2mm (2 units)7009060-2 170.00

eFiber 1.2mm (3 units)7009060-3 225.00

eFiber 1.2mm (5 units)7009060-5 350.00

eFiber 1.2mm(10 units)7009060-10 575.00

eFiber 1.6mm7009070 92.00

10 cm long wider diameter translucent polishable e-glass fiber for reinforced dentures, repairs, maryland bridges, and more!

7009070

7009060

Space Maintainer

Fiber Maryland

Fiber Ortho

7009050

Fiber Denture

Fiber Splint

Fiber Denture

7009050

301045

FP300016



90

90

Attachments

CLINICAL SPECIALTY

Chai

rsid

e At

tach

men

t Pic

kup

Mat

eria

l

Pink dual-cure Bis-Acryl chairside attachment pick up material, odorless and tasteless. Working time 2 minutes and 15 seconds, curing time 7 minutes (self cure). 4mL syringe enables the pickup of about 30 attachments.

CHAIRSIDE Pickup Material 4mL4009566 79.50

•Syringe and Plunger •15 Mixing Tips •15 Angled Tips



Low viscosity provides excellent control during chairside pickup. Ideal for picking up Temporary Cylinders in hybrid dentures!

Optimal handling characteristics:•Tissue-colored material bonds to itself.•Packaged with a straight and angled tip for precise application.•Dual cure – self or light cure.•The material will set in approximately 5 minutes from the moment the material is expressed from the tip. The working time is approximately 2 minutes and 15 seconds.•The material will self cure in approximately 7 minutes from the time the material is expressed from the tip. We recommend waiting the full 7 minutes to ensure reliable attachment fixation. Curing time can be shortened by light curing.

Cost efficient:•Shortened mixing tip length reduces waste and cost and increases the number of Attachments processed per syringe.•No primer required, reducing associated chairside time and cost.

Designed with patient comfort in mind•Odorless and tasteless•Low cure temperature

Denture Removal Tool (10-Pack)4009549 49.99

Simple prostheses removal tool, ideal for overdentures

4009566

4009566

4009566

4009566

4009565

4009549

4009549

4009549


91

91

Attachments

CLINICAL SPECIALTY

Chairside Attachment Pickup M

aterial

Perma Block E-Z Gun5851006 60.00

Perma Block is a specially designed, cellulose-based block-out material. The single dose syringes fit in a standard Centrix / Composite gun.

Perma Block will adhere to wet rubber dam, gingival and mucosal tissues and teeth. It does not distort when in contact with water and saliva!

Implantlink Temporary Cement0907500 79.99

Implantlink Tips (25-Pack)0907510 41.25

The first removable semi-permanent cement designed specifically for implant restorations.

*Dual cure for quick and easy application

* Light cure allows for easy to remove excess cement to maintain peri-implant health

* Strong enough to provided stability, yet easy to remove without damage

Wagner Impression Tray Maxillary7008002 21.00

Create a custom tray quality impression in just one short appointment.

The Wagner Tray is ready in just minutes. A Wagner Tray is customized chairside and in your patient’s mouth, eliminating the need for a second appointment.

Chairside Adjustment Kit0605000 60.00

Ideal for final chairside adjustments of acrylic prostheses

Contents include: 3 Silicone Cutter/Polishers (F8, F9, F10), 1 tube 244 Blue, and 1 mounted goat hair wheel.

Perma Block E-Z Single Dose (10-Pack)5851003 36.00

0605000

708002

708001

0907510

Implantlink

5851003

Perma Block

Perma Block

Wagner Impression Tray Mandibular7008001 21.00

95.00

275.00

58.00

40.00

72.00


91

91

Attachments

CLINICAL SPECIALTY


aterial

















0605000

708002

708001

0907510

Implantlink

5851003

Perma Block

Perma Block



91

91

Attachments

CLINICAL SPECIALTY


aterial

















0605000

708002

708001

0907510

Implantlink

5851003

Perma Block

Perma Block


48.009574 Chairside Blockout Material (4 x 1.2ml Syringes)

CLINICAL SPECIALTY ATTACHMENTS

78.00

345.00

9576

9582

Chairside Recess Bur

Chairside Denture Prep and Polish Kit


90

90

Attachments

CLINICAL SPECIALTY

Chai

rsid

e At

tach

men

t Pic

kup

Mat

eria

l

Pink dual-cure Bis-Acryl chairside attachment pick up material, odorless and tasteless. Working time 2 minutes and 15 seconds, curing time 7 minutes (self cure). 4mL syringe enables the pickup of about 30 attachments.





Low viscosity provides excellent control during chairside pickup. Ideal for picking up Temporary Cylinders in hybrid dentures!

Optimal handling characteristics:•Tissue-colored material bonds to itself.•Packaged with a straight and angled tip for precise application.•Dual cure – self or light cure.•The material will set in approximately 5 minutes from the moment the material is expressed from the tip. The working time is approximately 2 minutes and 15 seconds.•The material will self cure in approximately 7 minutes from the time the material is expressed from the tip. We recommend waiting the full 7 minutes to ensure reliable attachment fixation. Curing time can be shortened by light curing.

Cost efficient:•Shortened mixing tip length reduces waste and cost and increases the number of Attachments processed per syringe.•No primer required, reducing associated chairside time and cost.

Designed with patient comfort in mind•Odorless and tasteless•Low cure temperature

Denture Removal Tool (10-Pack)4009549 49.99

Simple prostheses removal tool, ideal for overdentures

4009566

4009566

4009566

4009566

4009565

4009549

4009549

4009549

9574

9576

9582

NEW!9702 Trephine Bur

9702


T5415

AUXILIARY CLINICAL SPECIALTY

405.00

75.00

75.00

75.00

75.00

75.00

75.00

75.00

75.00

285.00

07000269

T5415

T5410

T5405

T5400

T5445

T5440

T5435

T5430

70-1072-PRC0028

CM Torque Wrench (Latch Tips)

Latch Tip Hex .050 (Short)

Latch Tip Hex .050 (Long)

Latch Tip Hex .048 (Short)

Latch Tip Hex .048 (Long)

Latch Tip SCS Straumann (Short)

Latch Tip SCS Straumann (Long)

Latch Tip Unigrip Nobel (Short)

Latch Tip Unigrip Nobel (Long)

Inclusive Universal Driver Set (8 Pcs.)

70.1071-PRS0001

44-ATWP

41

All instruments associated with the Inclusive Tapered Implant System are machined from high-quality, corrosion-resistant, surgical stainless steel, and feature standard connectivity.

Features and Benefits

The Inclusive Tapered Implant Prosthetic Kit allows the clinician to easily organize, store, and transport the prosthetic tooling of the Inclusive Tapered Implant System. The autoclavable kit is designed specifically for restorative doctors, to help simplify prosthetic procedures and instrument sterilization.

Sterilization

It is recommended that the prosthetic kit be steam-sterilized for twenty (20) minutes at 132°C/270°F minimum.

General Cleaning Tips:

■ Observe universal precautions for the handling of contaminated or biohazardous materials.

■ Clean promptly after each use, to prevent biological fluids and tissues from drying on the instruments.

■ When applicable, disassemble parts and instruments prior to cleaning.

■ Do not rely solely on automatic cleaning. Thorough manual cleaning is recommended.

■ Preliminary cleaning should consist of wiping parts, soaking them in a lukewarm enzymatic solution for a minimum of twenty (20) minutes, and rinsing them with running water.

■ Routine cleaning should consist of (a) washing parts using a broad spectrum cleaning solution, followed by thorough rinsing and drying; and (b) sonicate parts fully submerged in cleaning solution for at least ten (10) minutes, preferably at 45-50 kHz, followed by thorough rinsing and drying.

■ Dry promptly and completely to avoid oxidation.

Description Code Price

Inclusive® Tapered Implant Prosthetic Kit 70-1071-PRS0001 $750

Prosthetic Kit

750.00

75.00

75.00

75.00

75.00

75.00

75.00

75.00

75.00

599.00

70.1071-PRS0001

44-HTLT

44-HTT

44-HNT

44-HNLT

44-ITIS

44-ITIL

44-PROCS

44-PROCL

44-ATWP

Inclusive Tapered Implant Prosthetic Kit (Square Tips)

Bio-Torque Tip Hex .050 (Short)

Bio-Torque Tip Hex .050 (Long)

Bio-Torque Tip Hex .048 (Short)

Bio-Torque Tip Hex .048 (Long)

Bio-Torque Tip SCS Straumann (Short)

Bio-Torque Tip SCS Straumann (Long)

Bio-Torque Tip Unigrip Nobel (Short)

Bio-Torque Tip Unigrip Nobel (Long)

Universal Torque Wrench Only (Square Tips)


92


92

92

Attachments


Perm

a Re

t



















Ging

ivam

oll

Perma Ret

0109000

Perma Ret

Perma Ret

6000005

Gingivamoll

Gingivamoll

Gingivamoll



ITL Torque Wrench




Features

CE Mark

Autoclavable

No Lubrication

Ratchet Mechanism

9 Torque Settings

15, 20, 25, 30, 35, 40

45, 50 and 60 Ncm

Order No. 44-ATW

44-HTLT


44-HTT


44-HNT


44-HNLT


44-ITIL


44-PROCS


44-PROCL


59-100180


59-100181

BIO-TORQ Tip Square .050” Cera1, Long

Order No.

8926


8927


44-ITIS


We Carry A W

ide


With Virtually All Screw

s &

Implant Com

ponents


rench


rench

T5415


T5405


8913


T5435








Order No.


Dura Pattern LC

- E�cient m

odeling gel.


Diamodent



all implant



cient rotating








plant jigs




• Zero shrinkage

33-T5590


33-T5500


33-T5510


33-T5520


33-T5530


33-T5540


33-T5550


33-T5580






eans of



plants.



ITL Torque Wrench




Features

CE Mark

Autoclavable

No Lubrication

Ratchet Mechanism

9 Torque Settings

15, 20, 25, 30, 35, 40

45, 50 and 60 Ncm

Order No. 44-ATW

44-HTLT


44-HTT


44-HNT


44-HNLT


44-ITIL


44-PROCS


44-PROCL


59-100180


59-100181

BIO-TORQ Tip Square .050” Cera1, Long Order No.

8926


8927


44-ITIS


We Carry A W

ide


With Virtually All Screws &

Implant Com

ponents


rench


rench

T5415


T5405


8913


T5435








Order No.


Dura Pattern LC

- E�cient m

odeling gel.


Diamodent



all implant



cient rotating








plant jigs




• Zero shrinkage

33-T5590


33-T5500


33-T5510


33-T5520


33-T5530


33-T5540


33-T5550


33-T5580






eans of



plants.

T5415

44-HTLT

07000269


CATALOG PRODUCT INDEXOVERDENTURE BARSHader Bar .......................................................................................................................................................... P.7Ackermann MD/BL ........................................................................................................................................ P.7 Uneversal Plunger Loc Attachment ....................................................................................................... P.7Dolder ............................................................................................................................................................... P.7Locator Bar Attachment .............................................................................................................................. P.18

OVERDENTURE STUDSO-Ring size chart ........................................................................................................................................... P.8Saturno .............................................................................................................................................................. P.8O-Rings .............................................................................................................................................................. P.9Zaag.................................................................................................................................................................... P.10,11Sterngold ERA ................................................................................................................................................. P.12,13Dalbo ................................................................................................................................................................. P.14Pro-Snap ........................................................................................................................................................... P.14Biloc .................................................................................................................................................................... P.14OT Cap ............................................................................................................................................................... P.23Equator .............................................................................................................................................................. P.24OT Strategy ...................................................................................................................................................... P.24

IMPLANT ABUTMENT / REMOVABLE ATTACHMENTLocator .............................................................................................................................................................. P.15 - 20 Locator R-Tx ..................................................................................................................................................... P.21,22CM-Loc .............................................................................................................................................................. P.2-5

IMPLANT ABUTMENT / FIXED ATTACHMENTLocator F-Tx ..................................................................................................................................................... P.26,27Multi-Unit Components .............................................................................................................................. P.25Dynamic Abutment ...................................................................................................................................... P.25

CLINICAL SPECIALTYSilicone Putty .................................................................................................................................................. P.28eFiber ................................................................................................................................................................. P.28Chairside Pickup Material ........................................................................................................................... P.29Denture Removal Tool ................................................................................................................................. P.29Perma Block/Perma Ret ............................................................................................................................... P.29

AUXILIARYTorque Wrenches ........................................................................................................................................... P.30Torque Tips....................................................................................................................................................... P.30Lab Drivers ....................................................................................................................................................... P.30

Toll Free: 1.800.387.5031 Tel: 905.479.2500 / www.swissnf.comE+O.E. Sales - 201

The Company for Dental Solutions

29

www.shera.de

SHERAprint 30

3D printer with Force Feedback Technology

- DLP process with long-lasting LED- patented Force Feedback Technology- RFID material identification- heated material bath- integrated 7” display- integrated 10” touch LCD monitor- LAN and WLAN- Made in Germany- can be integrated into open digital workflows- processing of STL files- wide range of high-quality light-curing SHERAprint resins, approved as medical devices depending on application- no additional support material required, very material-saving- automatic calibration for constant precision

- rapid return on investment

Technical data

Construction platform: 130 x 75 mm

Resolution: HD 1920 x 1080 pixel

(native pixels +/- 34 μm)

Max. construction height: 110 mm

Light source: UV LED 385 nm

Layer thickness: 50 and 100 μm standard

(min. layer thickness in z: 0.5 μm)

depending on the material

Construction speed: up to 100 mm/h,

depending on the material and layer thickness

Elect. connection: 110 - 250 V, 50 - 60 Hz

Dimensions: 480 x 410 x 690 mm (W x H x D)

Weight: approx. 40 kg

Item no.: SD104013

28

Dental catalogue

SHERAdigital2017

en

denture catalog - swiss nf metalsswissnf.com/wp-content/uploads/2018/12/denturist... · 2 female...

Documents