dball vw02 en ig ac20130430
TRANSCRIPT
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
† Audi, Seat, Skoda and Volkswagen are registered trademarks and property of their respective companies.
Vehicle Application Guide for European models..............................................................................................................Vehicle Application Guide for North American models.....................................................................................................Immobilizer Interface.......................................................................................................................................................
Wiring Diagram
TYPE 1A - Regular Key & Manual Transmission............................................................................................................. 06
TYPE 1B PTS & Automatic Transmission........................................................................................................................ TYPE 1B - Regular Key & Automatic Transmission.........................................................................................................TYPE 1B PTS & Manual Transmission............................................................................................................................ TYPE 1B - Regular Key & Manual Transmission.............................................................................................................Type 1B - Wiring Reference Charts.................................................................................................................................
TYPE 2A - Regular Key & Automatic Transmission.........................................................................................................TYPE 2A - Regular Key & Manual Transmission.............................................................................................................TYPE 2B - Regular Key & Automatic Transmission.........................................................................................................TYPE 2B - Regular Key & Manual Transmission.............................................................................................................
TYPE 3C - Regular Key & Manual Transmission............................................................................................................TYPE 4C - Regular Key & Manual Transmission............................................................................................................Type 3C & 4C - Wiring Reference Charts........................................................................................................................
Feature Programming......................................................................................................................................................
and Troubleshooting.......
Installation/TYPE 1A - Regular Key & Automatic Transmission.........................................................................................................
Feature & Option List.......................................................................................................................................................
020304
05
0708091011
12131415
161718
Programming.......................................................................................................... 19
Module Reset.................................................................................................................................................................. 212222
LED Diagnostics ...................................................................................................................... 23
Warranty........................................................................................................................................................................... 24
Module Programming............................................
Doorlock and many late Audi, Volkswagen, Seat and Skoda vehicles. Features include trunk release, comfort closure, door locks, turn signals, door trigger sensing, hood pin, trunk/hatch, ignition and tach output.
key Interface for
One universal transponder bypass module and one factory programmed key is required to install a remote starter.
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Vehicle Application Guide for European models
D: Data-to-Data (D2D) only•: D2D and Wire-to-Wire (W2W)
AV: Horn & Lights ControlCC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm ControlsFOB: Sync CAN Interface w/ FOB Remote
RS: Engine Start & StatusSS: Entry Point Status-Security
Legend:
* not available for some installation Type A2 ** not working for Type A2 installations witch turn signals dont work on CAN. This feature is default OFF (see Feature and Option list)VIN description: VWVXXX(1K)123456789
page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
A = BCM Type A C = BCM Type CC B A
B = BCM Type B
2013
2012
2011
2010
2009
2008
2007
2006
2005
2004
AUDIA1 (8X) 1B 1B 1B • • • • D • • D • D • • • • •A3 (8P) 1B 1B 1A or 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •A3 Cabrio (8P) 1B 1B 1A or 1B 1A 1A • • • • D • • D • D • • • • •Q3 (8U) 1B 1B 1B • • • • D • • D • D • • • • •R8 (42) 1A 1A 1A • • • • D • • D • D • • • • •TT (8J) 1B 1B 1B 1A or 1B 1A 1A 1A • • • • D • • D • D • • • • •SEATAlhambra (7N) 1B 1B 1B • • • • D • • D • D • • • • •Altea (5P) 1B 1B 1A or 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Ibiza IV (6J) 4C 4C 4C 4C 4C 4C D D • • • • • •Leon (1P) 1B 1B 1A or 1B 1A 1A 1A 1A • • • • D • • D • D • • • • •Toledo (5P) 1B 1B 1A or 1B 1A 1A 1A 1A • • • • D • • D • D • • • • •Mii (5P) 3C 3C D D • • • • •SKODACitigo (5J) 3C 3C D D • • • • • •Fabia (5J) 3C 3C 3C D D • D • • • • •Octavia Tour (1Z) 1B 1B • • • • D • • D • D • • • • •Octavia II (1Z) 1B 1B 1A or 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Octavia Scout (1Z) 1B 1B 1B • • • • D • • D • D • • • • •Praktik (5J) 3C 3C 3C D D • • • • • •Rapid (NH) 3C 3C D D • • • • • •Roomster (5J) 3C 3C 3C D D • • • • • •Superb II (3T) 1B 1B 1B 1B • • • • D • • D • D • • • • •Yeti (5L) 1B 1B 1A or 1B 1A • • • • D • • D • D • • • • •VOLSKWAGENAmarok (2H) 4C 4C D D • • • • • •Beatle (5J) 4C 4C D D • D • • • • •Caddy (2K) 1B 1B 1A or 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •EOS (1F) 1B 1B 1A or 1B 1A 1A 1A 1A • • • • D • • D • D • • • • •Golf V (1K) 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Golf V Plus (1K) 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Golf VI (1K) 1B 1B 1B • • • • D • • D • D • • • • •Golf VI Plus(1K) 1B 1B 1B • • • • D • • D • D • • • • •Jetta/Bora (1K) 1A 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Jetta High (1K or 16) 1B 1B 1B • • • • D • • D • D • • • • •Jetta Low (1K or 16) 4C 4C 4C D D • • • • • •Passat (3C) 2B 2B 2A 2A 2A 2A 2A 2A • • • • • D • • D • D • • • • •Passat CC (3C) 2B 2B 2A 2A 2A • • • • • D • • D • D • • • • •Polo V (6R) 4C 4C 4C D D • • • • • •Scirocco (13) 1B 1B 1A or 1B 1A 1A • • • • D • • D • D • • • • •Sharan (7N) 1B 1B • • • • D • • D • D • • • • •Tiguan (5N) 1B 1B 1A or 1B 1A 1A • • • • D • • D • D • • • • •Touran (1T) 1B 1B 1A or 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Up 3C 3C D D • • • • • •
RS
-B
rake
Sta
tus
RS
-Han
dbra
keS
tatu
s
DL-
Fuel
Doo
rRel
ease
SS
-Ent
ryS
tatu
sTr
unk/
Hat
chP
in
SS
-Ent
ryS
tatu
sD
river
sD
oorP
in
SS
-Ent
ryS
tatu
sA
LLD
oor
Pin
s
SS
-Ent
ryS
tatu
sH
ood
Pin
RS
-Ta
ch/R
PM
Out
put
RS
-Ig
nitio
nS
tatu
s
Vehicle Years & Installation Type for European Models
AV-
Turn
Sign
alCo
ntro
lON
/OFF
*
CC-
Com
fort
Clo
sure
**
DL-
Arm
/Dis
arm
Fact
ory
Sec
urity
DL-
Doo
rLoc
kC
ontro
l
DL-
Doo
rUnl
ock
DL-
Tru
nk/H
atch
Rel
ease
FO
B-C
ontro
lofa
fterm
arke
dal
arm
with
OE
Mre
mot
e
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Vehicle Application Guide for North American models
* not available for some installation Type A2 ** not working for Type A2 installations witch turn signals dont work on CAN. This feature is default OFF (see Feature and Option list)
A = BCM Type A
VIN description: VWVXXX(1K)123456789
C = BCM Type CC B A
B = BCM Type B
page 3
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
D: Data-to-Data (D2D) only•: D2D and Wire-to-Wire (W2W)
AV: Horn & Lights ControlCC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm ControlsFOB: Sync CAN Interface w/ FOB Remote
RS: Engine Start & StatusSS: Entry Point Status-Security
Legend:
2013
2012
2011
2010
2009
2008
2007
2006
2005
2004
AUDIA3 (8P) 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •A3 (FM) 1B 1B 1B 1A 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •A3 Cabrio (8P) 1A 1A 1A • • • • D • • D • D • • • • •A3 Cabrio (FM) 1B 1B • • • • D • • D • D • • • • •R8 (42) 1A 1A • • • • D • • D • D • • • • •R8 (FG) 1B 1B 1B 1B • • • • D • • D • D • • • • •TT (8J) 1A 1A 1A • • • • D • • D • D • • • • •TT (FK) 1B 1B 1B 1B • • • • D • • D • D • • • • •VOLSKWAGENBeatle (AT) 3C 3C D D • • • • • •EOS (1F) 1A 1A 1A 1A • • • • D • • D • D • • • • •EOS (AH) 1B 1B 1B • • • • D • • D • D • • • • •Golf Rabbit (1K) 1A 1A 1A 1A • • • • D • • D • D • • • • •Golf (AJ) 1B 1B 1B 1B • • • • D • • D • D • • • • •Golf Wagon (AJ) 1B 1B 1B • • • • D • • D • D • • • • •Jetta (1K) 1A 1A 1A 1A 1A • • • • D • • D • D • • • • •Jetta (High) (AJ) 1B 1B 1B • • • • D • • D • D • • • • •Jetta (Low) (AJ) 3C 3C 3C D D • • • • • •Jetta SportWagen (AJ) 1B 1B 1B • • • • D • • D • D • • • • •Passat (3C) 2A 2A 2A 2A 2A 2A • • • • • D • • D • D • • • • •Passat (AN) 2B 2B • • • • • D • • D • D • • • • •Passat CC (3C) 2A 2A 2A • • • • • D • • D • D • • • • •Passat CC (AN) 2B 2B • • • • • D • • D • D • • • • •Tiguan (5N) 1A 1A • • • • D • • D • D • • • • •Tiguan (AX) 1B 1B 1B • • • • D • • D • D • • • • •
DL-
Fuel
Doo
rRel
ease
Vehicle Years & Installation Type for North American models
DL-
Doo
rLoc
kC
ontr
ol
DL-
Doo
rUnl
ock
DL-
Trun
k/H
atch
Rel
ease
RS
-H
andb
rake
Sta
tus
DL-
Arm
/Dis
arm
Fac
tory
Sec
urity
FOB
-Con
trol
ofaf
term
arke
dal
arm
with
OE
Mre
mot
e
AV-
Turn
Sign
alC
ontr
olO
N/O
FF*
CC-
Com
fort
Clo
sure
**
SS
-Ent
ryS
tatu
sD
river
sD
oorP
in
SS
-Ent
ryS
tatu
sA
LLD
oorP
ins
SS
-Ent
ryS
tatu
sH
ood
Pin
SS
-Ent
ryS
tatu
sTr
unk/
Hat
chP
in
RS
-Ta
ch/R
PM
Out
put
RS
-Ig
nitio
nS
tatu
s
RS
-B
rake
Sta
tus
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
30
86 8587
87a
4-6turns
Ground While Running(remote starter)
(+) 12v
Immobilizer interface
Factory transponder
reader
Factory transponder
reader
2. Loop immobilizer
IMPORTANT!: Not all OEM remotes can be inserted in TBXKEY because of their size. Make sure that the key can be disassembled, otherwise it is recomanded to use Loop Immobilizer installation.
page 4
Ground While Running (GWR Status) from Remote Starter
NOTE: Your OEM remote may differ from the model shown in the illustrations.
PIN 5 Green
PIN 1 Black
PIN 6 Brown
PIN 4 Blue
PIN 2 RedPIN 3 Violet
48
(+) 12 Volt ConstantChassis Ground
1. Standard immobilizer interface with TBXKEY TBXKEY are sold SEPARATELY. Request an order from Directed using the part numbers listed below.UPC: 093207 062445
Move antenna loop as closeto the front of ignition cylinder (factory receiver ring) as possible. Test before closing installation.
Move antenna loop as closeto the front of ignition cylinder (factory receiver ring) as possible. Test before closing installation.
- Make 4-6 loops and place them as close to the front of ignition cylinder (factory receiver ring) as possible.
- Test and secure mounted loops before reassembling the vehicle.- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
For vehicles with you must remove battery from OEM Remote Control.Keyless Entry
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Wiring Diagram TYPE 1A - Regular Key & Automatic Transmission
3: Green/White (-) Door Status Output4: Red/Black (-) Status OutputTrunk
6: Gray: Brake Bypass Activation Output8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output(+) Parking Lights Output(+) Start Output(+) Ignition Input/Output(-) GWR (Status)
Rem
ote Starter
(-) Hood Status Input
(+) Brake Status Input
(-) Status InputTrunk(-) Door Status Input
BCM Type A- Driver side,
under dashboard
Brake Switch
(only when the engine does not start without brake)
10: Yellow/Black: (-) Handbrake Status Output
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
13: Red: (+) 12 V14: Black: (-) Ground(-) Ground
(+)12V
4
TX(-) GroundRX(+)12v
XKD2D65
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
(-) Ground(-) Ground(+) 12V(+) 12 V
F HGE
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
6542 31
1211108
9
7
pin 1: Red/Black (+) Starter
G plug at BCM
(+) Ignition pin 11: Black
pin 7: Orange/ Brown (CAN L)pin 8: Orange/Green (CAN H)
5: Violet/White: (AC) Tach Status Output
(AC) Tach Input
page 5
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Wiring Diagram TYPE 1A - Regular Key & Manual Transmission
3: Green/White (-) Door Status Output
5: Violet/White: (AC) Tach Status Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output(+) Parking Lights Output(+) Start Output(+) Ignition Input/Output(-) GWR (Status)
Rem
ote Starter
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Trunk Status Input(-) Door Status Input
BCM Type A- Driver side,
under dashboard
10: Yellow/Black: (-) Handbrake Status Output
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
7: Brown: NO Relay 18: Yellow: Com Relay 1
13: Red: (+) 12 V14: Black: (-) Ground
(-) Ground
(-) Ground(+)12V
4
TX(-) GroundRX(+)12v
XKD2D65
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
(-) Ground(-) Ground(+) 12V(+) 12 V
E
6542 31
1211108
9
7
pin 1: Red/Black (+) Starter
G plug at BCM
(+) Ignition pin 11: Black
pin 7: Orange/ Brown (CAN L)pin 8: Orange/Green (CAN H)
168
9
1
10
2
11
3
12
4
13
5
14
6
15
7
pin 7: ) Violet/Black (Clutch
Connect this wire, only when the does not start without clutch
engine E plug at BCM
page 6
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
GF H
(-) Neutral Safety/Handbrake Status Input
4: Red/Black (-) Status OutputTrunk
12: Blue/Red: (-) Hood Status Output
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
pin 15
pin 15: Orange/Green (CAN H)
pin 7: Hazard Switch (Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)pin 17: Footbrake Bypass (only when the
engine does not start without brake)
pin 16
pin 17
pin 7
52 112441
42 125
122928
C Plug (Brown) at BCM (see page 9 for wiring reference chart)
Remote
Starter
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
(+) 12v 13: Red: (+) 12v14: Black: (-) Ground
5: Violet/White: (AC) Tach Output6: Gray: (+) Brake Bypass Output7: Gray/Black: (+) Ignition Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
3: Green/White: (-) Door Status Output
1: Black/White: (-) Hazard SW Output2: Green/Black: PTS Output
4: Red/Black: (-) Status OutputTrunk
(-) Ground
(-) GWR (Status)(+) Ignition Input/Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output
5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
2 x D
iodes
, 1A
pin 4pin 3
(see page 10 for wiring reference chart)
BC A
BCM Type B - Driver side under dashboard
Wiring Diagram TYPE 1B - PTS & Automatic Transmission
10
1412
2
DBALLProgramming button
LED
RF Loop connector
4
TX(-) GroundRX(+)12v
XKD2D65
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Trunk Status Input(-) Door Status Input
(-) Ground(-) Ground(+) 12V(+) 12 V
page 7
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
Located at PTS button
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Remote
Starter
(+) 12v 13: Red: (+) 12v14: Black: (-) Ground
5: Violet/White: (AC) Tach Output6: Gray: (+) Brake Bypass Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
3: Green/White: (-) Door Status Output
1: Black/White: (-) Hazard SW Output
4: Red/Black: (-) Trunk Status Output
(-) Ground
(-) GWR (Status)(+) Ignition Input/Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output
pin 15
pin 15: Orange/Green (CAN H)
pin 7: Hazard Switch (Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)pin 17: Footbrake Bypass (only when the
engine does not start without brake)
pin 16
pin 17
pin 7 5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
52 112441
42 125
122928
C Plug (Brown) at BCM
Steering Column Control Unit
(see page 9 for wiring reference chart)
6
17
14
pin 6: (+)Starter
pin 17: (+)Ignitionpin 18: (+)Starter
pin 14: (+)Ignition)
Steering Column Control Unit
OR
1 89 16
(see page 9 for wiring reference chart)
Connections for Ignition and Starter can be madein two ways depending on the vehicle equipment.
181091
BC A
BCM Type B - Driver side under dashboard
10
1412
2
DBALLProgramming button
LED
RF Loop connector
4
TX(-) GroundRX(+)12v
XKD2D65
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Trunk Status Input(-) Door Status Input
(-) Ground(-) Ground(+) 12V(+) 12 V
Wiring Diagram TYPE 1B - Regular Key & Automatic Transmission
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
page 8
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
2 x D
iodes
, 1A
pin 4pin 3
(see page 10 for wiring reference chart)
Located at PTS button
pin 15
pin 30
pin 15: Orange/Green (CAN H)
pin 7: Hazard Switch (Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)pin 30: Clutch (1) Bypass for vehicles
without Start/Stop system (only when the engine does not start without clutch)
pin 16pin 7
14 42 1125
42 125
122928
C Plug (Brown) at BCM (see page 9 for wiring reference chart)
B Plug at ECM
12
56
94 28
773
5072
Clutch (2) Bypass(For vehicles with Start/Stop System)
pin 42
pin 20
Clutch can be found on pin 20 or 42 depending on the vehicle engine
(see page 9 for wiring reference chart)
OR
1: Black/White: (-) Hazard SW Output2: Green/Black: PTS Output
3: Green/White: (-) Door Status Output4: Red/Black: (-) Status OutputTrunk
5: Violet/White: (AC) Tach Output7: Gray/Black: (+) Ignition Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
10: YellowBlack: (-) Handbrake Status Output12: Blue/Red: (-) Hood Status Output
Remote
Starter
(+) 12v(-) Ground
(-) Ground
(-) GWR (Status)(+) Ignition Input/Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release Output
(-) Hood Status Input
(+) Brake Status Input(AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
Aux 1 OutputAux 2 OutputAux 3 Output
13: Red: (+) 12v14: Black: (-) Ground
7: Brown: NO Relay 18: Yellow: Com Relay 1
5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
BC A
BCM Type B - Driver side under dashboard
Wiring Diagram TYPE 1B - PTS & Manual Transmission
B
A
ECM - under the windshield wiper motor cowling
1412
2
DBALLProgramming button
LED
RF Loop connector
(-) Ground(-) Ground(+) 12V(+) 12 V
4
TX(-) GroundRX(+)12v
XKD2D65
10
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
page 9
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
pin 15
pin 30
pin 15: Orange/Green (CAN H)
pin 7: Hazard Switch (Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)pin 30: Clutch (1) Bypass for vehicles
without Start/Stop system (only when the engine does not start without clutch)
pin 16pin 7
14 42 1125
42 125
122928
C Plug (Brown) at BCM (see page 9 for wiring reference chart)
1: Black/White: (-) Hazard SW Output
3: Green/White: (-) Door Status Output4: Red/Black: (-) Status OutputTrunk
5: Violet/White: (AC) Tach Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
10: YellowBlack: (-) Handbrake Status Output12: Blue/Red: (-) Hood Status Output
6
17
14
Remote
Starter
(+) 12v(-) Ground
(-) Ground
(-) GWR (Status)(+) Ignition Input/Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release Output
(-) Hood Status Input
(+) Brake Status Input(AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
Aux 1 OutputAux 2 OutputAux 3 Output
pin 6: (+)Starter
pin 17: (+)Ignitionpin 18: (+)Starter
pin 14: (+)Ignition
Steering Column Control Unit
Steering Column Control Unit
OR
1 89 16
(see page 9 for wiring reference chart)
Connections for Ignition and Starter can be madein two ways depending on the vehicle equipment.
181091
B
A
B Plug at ECM
12
56
94 28
773
5072
Clutch (2) Bypass(For vehicles with Start/Stop System)
pin 42
pin 20
Clutch can be found on pin 20 or 42 depending on the vehicle engine
(see page 9 for wiring reference chart)
OR
13: Red: (+) 12v14: Black: (-) Ground
7: Brown: NO Relay 18: Yellow: Com Relay 1
5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
BC A
BCM Type B - Driver side under dashboard
Wiring Diagram TYPE 1B - Regular Key & Manual Transmission
ECM - under the windshield wiper motor cowling
1412
2
DBALLProgramming button
LED
RF Loop connector
(-) Ground(-) Ground(+) 12V(+) 12 V
4
TX(-) GroundRX(+)12v
XKD2D65
10
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
page 10
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
(-) Hazard (+) Brake (-) Clutch (1) (no Start/Stop)
(-) Clutch (2) (with Start/Stop) (-) PTS Button Steering Column 1 Steering Column 2
T52C - pin 7 T52C - pin 17 T52C - pin 30 T94 (ECM) Pin 3 Pin 4 IGN (pin 14) Start (pin 6) IGN (pin 17) Start (pin 18)
AUDI
A1 Brown/Red
Brown/Red
Brown/Red
Brown/Red
Violet
Brown/Red
Brown/Red
Brown/Red
Brown/Red
Violet/Red
Violet/White
Brown/Red
Brown/Red
Brown/Red
Blue/White Red/White Red/White
A3 Brown/Red
Brown/Red
no info
no info
no info
Red/Blue
no info
no info
no info
Green
Brown
Yellow/White
no info
no info
no info
no info
no info
N/A
N/A
N/A
SEAT
Altea
Altea XL
Altea Freetrack
Leon II
SKODA
Octavia II & Tour
Superb II
Yeti
VOLKSWAGEN
Caddy N/A N/A Black
EOS
Golf VI
Jetta (HIGH)
Scirocco
Sharan
Tiguan
Touran
Wiring Reference Chart- TYPE 1B -
no infono infono infono infono infono infono info no info no info no info
page 11
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/White
Red/Black
Red/Black
Red/Black
Black/Green
Red/Black
Black/GreenRed/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/Black
Red/White
Red/Black
Red/Black
Red/Black
Black/Green
Black
Black
Black
Black
Black
Black
Black
Red/Violet
Black
Black
Black
Black
Black
Black
Black/Greenno info
Brown/YellowViolet/White
White/Red
Violet/White
Violet/White
Violet/White
Black/Red
Black/Red
Black/Red
Black/Red
YellowBlack
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Violet/Black
Violet/Black
Black/Yellow
N/A
N/A
N/A
Violet/White
Violet/Blue
Violet/Yellow
Violet/Yellow
Violet/Black
Violet/Black
N/A
N/A
N/A
Violet/Blue
N/A
N/A
N/A
N/A
Violet
WhiteViolet
N/A
N/A
N/A
Violet/Gray
N/A
Black
Black
Black
Black
Black
Black
Red/Violet
Black
Black
Black
Black
Black
Black
(pin20) or (pin42)
Black
Violet/White(pin20) or (pin42)
Red/Blue(pin20) or (pin42)
Violet/White(pin20) or (pin42)
Violet/White(pin20) or (pin42)
Violet/White(pin20) or (pin42)
Black orBlue/Black
Black orBlue/Black
Red/Black orRed/Green
Red/Black orRed/Green
Violet/Black(pin20) or (pin42)
Violet/Black(pin20) or (pin42)
Brown/Red Brown/Blue
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
Wiring Diagram TYPE 2A - Regular Key & Automatic Transmission
3: Green/White (-) Door Status Output4: Red/Black (-) Status OutputTrunk
5: Violet/White: (AC) Tach Status Output6: Gray: Brake Bypass Activation Output8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output(+) Parking Lights Output(+) Start Output(+) Ignition Input/Output(-) GWR (Status)
Rem
ote Starter
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
13: Red: (+) 12 V14: Black: (-) Ground(-) Ground
(+)12V
4
TX(-) GroundRX(+)12v
XKD2D65
(-) Ground(-) Ground(+) 12V(+) 12 V
BCM Type A- Driver side,
under dashboard
F HGE
6542 31
1211108
9
7
pin 1: Red/Black (+) Starter
G plug at BCM
(+) Ignition pin 11: Black
pin 7: Orange/ Brown (CAN L)pin 8: Orange/Green (CAN H)
(-) GWR (status)
30
86 8587
87a(+) 12 V
816
715
614
513
412
311
210
19
CUT
Ignition Switch Plug(located at Key Slot)
pin 16:Green
pin 3: Green/Red
Brake Switch
(only when the engine does not start without brake)
page 12
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) AUX 1 Input*5: Violet/Black: (-) AUX 2 Input*6: White/Black: (-) AUX 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
Wiring Diagram TYPE 2A - Regular Key & Manual Transmission
3: Green/White (-) Door Status Output4: Red/Black (-) Status OutputTrunk
5: Violet/White: (AC) Tach Status Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output(+) Parking Lights Output(+) Start Output(+) Ignition Output
Rem
ote Starter
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
BCM Type A- Driver side,
under dashboard
6542 31
1211108
9
7
pin 1: Red/Black (+) Starter
G plug at BCM
(+) Ignition pin 11: Black
10: Yellow/Black: (-) Handbrake Status Output
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
7: Brown: NO Relay 18: Yellow: Com Relay 1
13: Red: (+) 12 V14: Black: (-) Ground
(-) Ground
(-) Ground(+)12V
4
TX(-) GroundRX(+)12v
XKD2D65
(-) Ground(-) Ground(+) 12V(+) 12 V
F HGE
(-) GWR (status)
30
86 8587
87a(+) 12 V
816
715
614
513
412
311
210
19
CUT
Ignition Switch Plug(located at Key Slot)
pin 16:Green
pin 3: Green/Red (-) GWR (Status)
pin 7: Orange/ Brown (CAN L)pin 8: Orange/Green (CAN H)
168
9
1
10
2
11
3
12
4
13
5
14
6
15
7
pin 7: ) Violet/Black (Clutch
Connect this wire, only when the does not start without clutch
engine E plug at BCM
page 13
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Wiring Diagram TYPE 2B - Automatic Transmission
Remote
Starter
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) Aux1 Input*5: Violet/Black: (-) Aux2 Input*6: White/Black: (-) Aux3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
(+)12v 13: Red: (+) 12v14: Black: (-) Ground
5: Violet/White: (AC) Tach Output6: Gray: (+) Brake Bypass Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output
3: Green/White: (-) Door Status Output1: Black/White: (-) Hazard SW Output
4: Red/Black: (-) Status OutputTrunk
(-) Ground
(-) GWR (Status)(+) Ignition Input/Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output
pin 15
pin 15: Orange/Green (CAN H)
pin 7: Brown/Red (Hazard Switch - Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)pin 17: Red/Black ( Footbrake Bypass only when the engine does not start without brake)
pin 16
pin 17
pin 7
5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
C Plug (Brown) at BCM
52 112441
42 125
122928
ECM - under the windscreen wiper ornament BC A
BCM Type B - Driver side under dashboard
10
1412
2
DBALLProgramming button
LED
RF Loop connector
pin 6: Red/Brownpin 5: Red/Green
pin 16: Green
IgnitionSwitch
Plug
(located atKey Slot)
1 89 16
30
86 8587
87a(+) 12V (-) GWR status
4
TX(-) GroundRX(+)12v
XKD2D65
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
(-) Ground(-) Ground(+) 12V(+) 12 V
page 14
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
page 15Wiring Diagram TYPE 2B - Manual Transmission
Remote
Starter
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input2: Blue: (-) Unlock Input3: Red/White: (-) Trunk Release Input4: White/Violet: (-) Aux 1 Input*5: Violet/Black: (-) Aux 2 Input*6: White/Black: (-) Aux 3 Input*
8: Violet: (+) Start Input9: Pink: (+) Ignition Input10: Blue/White: (-) GWR (Status) Input
(+)12v 13: Red: (+) 12v14: Black: (-) Ground
5: Violet/White: (AC) Tach Output
8: Purple/Green: (+) Brake Status Output9: Purple/Brown: (+) Brake Status Output
12: Blue/Red: (-) Hood Status Output11: Orange/Black: Clutch Pulse Output
3: Green/White: (-) Door Status Output1: Black/White: (-) Hazard SW Output
10: Yellow/Black: (-) Handbrake Status Output
4: Red/Black: (-) Status OutputTrunk
(-) Ground
(-) Ground
(-) GWR (Status)(+) Ignition Output(+) Start Output(+) Parking Lights Output
(-) Lock Output(-) Unlock Output(-) Trunk Release OutputAux 1 OutputAux 2 OutputAux 3 Output
11: Yellow/Red: Com Relay210: Orange/Red: NC Relay2
7: Brown: NO Relay 18: Yellow: Com Relay 1
pin 15
pin 15: Orange/Green (CAN H)
pin 7: Brown/Red (Hazard Switch) (Connect this Wire only if turn signals don’t work on CAN)
pin 16: Orange/Brown (CAN L)
pin 16pin 7
5: Orange/Green: FT CAN High6: Orange/Brown: FT CAN Low
C Plug (Brown) at BCM
B Plug at ECM
2 X Diodes, 1A
12
56
94 28
773
5072
Clutch Bypass
CutClutch Bypass
Voltage Test:
2.Clutch depressed: 4.15 Volts
1.Clutch notdepressed: 1.3 Volts
With Ignition ON:
pin 43
pin 20pin 63: (-) Red/White
Blue/Yellow(Trunk Side)
Blue/Yellow (Hood Side)
Blue/Yellow(finding wire)
52 112441
42 125
122928
Under the Carpet
ECM - under the windscreen wiper ornament
B
A
or (-) Violet/Yellow pin 42: (-) Violet/Black
(only when the engine does not start without clutch)
Clutch can be found on pin 42 & 63 or 20 & 43
depending on the vehicle engine
(only when the engine doesnot start without clutch)
BC A
BCM Type B - Driver side under dashboard
pin 6: Red/Brownpin 5: Red/Green
pin 16: Green
IgnitionSwitch
Plug
(located atKey Slot)
1 89 16
ECM - under the windshield wiper motor cowling
10
1412
2
DBALLProgramming button
LED
RF Loop connector
30
86 8587
87a(+) 12V (-) GWR status
(-) Hood Status Input
(+) Brake Status Input (AC) Tach Input
(-) Status InputTrunk(-) Door Status Input
(-) Ground(-) Ground(+) 12V(+) 12 V
4
TX(-) GroundRX(+)12v
XKD2D65
* See the Feature and Option list section for the Auxiliary Channel programming options.Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
See page 18 for wiring reference chart
B Plug (White)at BCM
Orange/Green: pin 20 - CAN H
Orange/Brown: pin 21 - CAN L
63
73
37
16
171
Wiring Diagram TYPE 3C
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
13: Red: (+) 12 V14: Black: (-) Ground
1: Black/White: Hazard Activation3: Green/White (-) Door Status Output
4: Red/Black (-) Status OutputTrunk5: Violet/White: (AC) Tach Status Output6: Gray: Brake Bypass Activation Output
10: Yellow/Black: Handbrake Status Output
7: Pink/White: (+) Parking Lights Input
(+) Parking Lights Output (-) Lock Output(-) Unlock Output
Rem
ote Starter
Ground(+)12V
(+) 12 VRX(-) GroundTX
(AC) Tach Input
(-) Status InputTrunk
(-) Door Status Input
Unlock180 Ω
Lock
(+) Accessory (+) Ignition (+) Starter
A Plug (Black)at BCM
BCM - Driver side, under dashboard
63
73
37
16
171
pin 24 - Key Lock (-)
pin 28 - Hazard (-)
P#: XKD2D65
D2DDATA TO DATA™
104
1412
2
DBALLProgramming button
LED
RF Loop connector
(Footbrake Bypass - only when the engine does not start without brake)
pin 43 - Brake (+)
Ignition Switch
(-) Ground(-) Ground(+) 12V(+) 12 V
page 16
Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
B Plug (White)at BCM
Orange/Green: pin 20 - CAN H
Orange/Brown: pin 21 - CAN L
63
73
37
16
171
Wiring Diagram TYPE 4C
5: Orange/Green FT CAN High6: Orange/Brown FT CAN Low
13: Red: (+) 12 V14: Black: (-) Ground
1: Black/White: Hazard Activation3: Green/White (-) Door Status Output
4: Red/Black (-) Status OutputTrunk5: Violet/White: (AC) Tach Status Output6: Gray: Brake Bypass Activation Output
10: Yellow/Black: Handbrake Status Output
7: Pink/White: (+) Parking Lights Input
(+) Parking Lights Output (-) Lock Output(-) Unlock Output
Rem
ote Starter
Ground(+)12V
(+) 12 VRX(-) GroundTX
(AC) Tach Input
(-) Status InputTrunk
(-) Door Status Input
Unlock
Lock
(+) Accessory (+) Ignition (+) Starter
A Plug (Black)at BCM
BCM - Driver side, under dashboard
63
73
37
16
171
pin 28 - Hazard (-)
P#: XKD2D65
D2DDATA TO DATA™
104
1412
2
DBALLProgramming button
LED
RF Loop connector
(Footbrake Bypass - only when the engine does not start without brake)
pin 43 - Brake (+)
Ignition Switch
(-) Ground(-) Ground(+) 12V(+) 12 V
560 Ω
pin 25 - Central Lock (-)
Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.With the exception of the OBII Diagnotistic plug, all connectors are displayed from the wire side.
(-) Neutral Safety/Handbrake Status Input
page 17
See page 18 for wiring reference chart
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Wiring Reference Chart page 18
* Connect this wire only when the engine does not start without brake
(-) Hazard (-) Key Lock (for type 3C)
(-) Central Lock (for type 4C)
A Plug - Pin 28 A Plug - Pin 24 A Plug - Pin 25
White/Green
White/Green
Brown/Black
White/Green
Brown/Red
White/Green
White/Green
Brown/Red
White/Green
White/Blue
White/Green
White/Green
Ibitza IV
Citigo
Amarok
Praktic
Jetta (LOW)
Mii
Fabia
Beetle
Rapid
Polo V
Roomster
UP
Yellow/Blue
Yellow/Blue
Blue/Red
Yellow/Blue
Yellow/Blue
Blue/Red
Yellow/Blue
Yellow/Blue
Yellow/Blue
Gray/Red
N/A
N/A
N/A
N/A
N/A
N/A
Brown/RedBrown/Blue
Brown/Green
Brown/Green
Brown/Green
Black/Red
Black/Red
Black/Gray
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
Black/Red
(+) Brake*
SEAT
SKODA
A Plug - Pin 43
VOLKSWAGEN
- TYPE 3C & 4C -
N/A
N/A
N/A
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Module Programming
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.
1. Connect the interface module to your computer using the XKLoader2.2. Open an Internet Explorer browser (version 6 or higher), and go to www.xpresskit.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top left corner of the page.3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware. 4. In the search result page, select one of the available install options (config for RSR, RXT or Standard install), and follow the
instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.
Warning!
2
3
4
5
Solid
Wait until the LED turns ON solid red and press the Unlock button on the OEM remote.
1 OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
W2W Installation10-pinD2D
st1
12-pin14-pin
nd2rd3
10-pinD2D
st1th4
12-pin14-pin
nd2rd3
For vehicles with Regular Keys
Turn the ignition ON.
The green LED turns ON for 3 seconds and shuts off.
Turn the ignition OFF.
&
&
Solid x3 secs OFF
Key
Key Out
OFF
START
IGN
OFF
START
IGN
Go to the next page to make the module programming for vehicles with PTS.
PRESS UNLOCK
page 19
Refer to the LED Diagnostics section of this guide for more information and for troubleshooting purposes.
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
4
3
5
6
1 OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
W2W Installation10-pinD2D
st1
12-pin14-pin
nd2rd3
10-pinD2D
st1th4
12-pin14-pin
nd2rd3
For vehicles with PTS
The green LED turns ON for 3 seconds and shuts off. &Solid x3 secs OFF
For vehicles with PTS, make sure the key is inside the vehicle.Key Inside the Vehicle
Important: Do NOT press the brake pedal.Press the Push-to-Start (PTS) button twice to turn the ignition ON. 2X ENGINE
STARTSTOP
PUSHDo NOTpress the brake pedal
Press the Push-to-Start (PTS) button once more to turn the ignition OFF. 1X ENGINE
STARTSTOP
PUSH
2Solid
Wait until the LED turns ON solid red and press the Unlock button on the OEM remote. &
PRESS UNLOCK
page 20
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
Module Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will erase the module programming only (bypass, convenience and vehicle detection). All the settings configured on the module using the web config tool will remain untouched.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation10-pinD2D
st1
12-pin14-pin
nd2th4
rd3
10-pinD2D
st1th5
12-pin14-pin
nd2rd3
th4
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will erase all the data stored in the DBALL and will change all the settings configured on the module to its default values. After a hard reset, you may have to reconfigure your DBALL if your installation requires specific options, not part of the default configuration. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation10-pinD2D
st1
12-pin14-pin
nd2th4
rd3
10-pinD2D
st1th5
12-pin14-pin
nd2rd3
th4
Hard Reset
page 21
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
To enter feature programming routineTurn the ignition ON, then OFF. Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button.The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Accessing another featurePress and release the programming button a number of times to advance from the current feature to the next desired . The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmedOther features can be programmed.The feature programming can be exited.
--
-
--
--
Changing feature optionsPress the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature.
--
The flashing sequence will repeat until a new command is entered.
feature
The flashing sequence will repeat until a new command is entered.
Exiting feature programming-
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON for 2 seconds to confirm .
No activity for 30 seconds; after 30 seconds, the LED will turn ON for 2 seconds to confirm the end of the programming orange
orange the end of the programming sequence
Feature Programming Programming Button
Feature & Option ListIt is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.xpresskit.com. The web offers more options; however, a manual configuration of the features is possible using the information on this page.
page 22
** not working for Type A2 installations witch turn signals dont work on CAN. This feature is default OFF
Feat. Operation Flashes/Options Description1. No RF Output* Module is connected to a remote starter using a standard installation.2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Disabled*2. Enabled1. Enabled* Takeover is activated for 45 seconds after pressing unlock button2. Disabled Engine shutdown when door opens.1. OFF*2. Windows Roll Up3. Front Windows Roll Down4. Rear Windows Roll Down5. Fuel Door Release1. OFF*2. Windows Roll Up3. Front Windows Roll Down4. Rear Windows Roll Down5. Fuel Door Release1. OFF*2. Windows Roll Up3. Front Windows Roll Down4. Rear Windows Roll Down5. Fuel Door Release
* Default Option
RFTD Output Type1
2 Comfort Closure**
6 AUX 3
AUX 14
5 AUX 2
3 Takeover
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
LED Diagnostics & Troubleshooting
Flashes
Flashes
Flashes x1
Flashes x4
Flashes x2
Flashes x5
Flashes x3
Flashes x6
Off
LED Status Description Troubleshooting
Solid Red.Waiting for the vehicle to be started.
Solid Red for 30 seconds,then flashes 1x
Solid Red for 30 seconds,then flashes 4x
Solid Red for 30 seconds,then flashes 5x
FT CAN not detected.
Invalid VIN.
Internal error.
The CAN wires may be incorrectly connected. Refer tothe wiring diagram to make the right connections.
The VIN number is invalid. Report issue to technicalsupport.
Report issue to technical support.
Solid Red for 30 seconds,then flashes 3x
Invalid CAN network.The CAN bus was detected but the ignition on CANmessage is not detected. Check if the firmware from unit is correct.
Flashes Greencontinuously.
Flashes Greencontinuously.
Ignition has been successfullydetected. N/A.
Solid Green for 3 seconds.Module has been successfullyprogrammed.
Ground out (GWR) is active. N/A.
Off. N/A.
Flashes Green 1x
Flashes Green 4x
Lock command has beenreceived.
AUX 1 command has beenreceived.
Flashes Green 2x
Flashes Green 5x
Unlock command received.
has been
AUX 2 command received.
has been
Flashes Green 3x
Flashes Green 6x
Trunk release command been received.
has
AUX 3 release command been received.
has
Solid x30 secs
Solid x30 secs
Solid x30 secs
Flashes x1
Flashes x4
Flashes x5
Solid x30 secsFlashes x3
Solid x3 secs
Solid
Inactive Ground While Running
Active Ground While Running
Module Programming
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
The Ground While Running (status) wire is incorrectlyconnected. Refer to the wiring diagram to make the right connections.
Make sure that all the connections are correct (see install sheet) and turn the ignition ON to begin the programming sequence.
N/A.
page 23
Rev.: 20130430
Platform: DBALLFirmware: VW02
© 2012 Directed. All rights reserved.
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE ORREPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
920-0007 2009-09
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited One Year Consumer Warranty
Additional information can be found at:
www.xpresskit.comwww.directechs.com
page 24
Vehicle Takeover for Type 1
* Your aftermarket remote may differ from the model shown in the illustrations.
4
5
3
1 Press the remote start button on the transmitter to start the vehicle.*
2
Turn the key into the run/ignition position.
You can now press the brake pedal, put the car in gear and drive off.
Press the Unlock button on theaftermarket remote.*
Ready to drive off
Press remote start
button*
Press Unlock button on
either remote*
Enter vehicle
Key OFF
START
IGN
Vehicle Takeover for Type 2
* Your aftermarket remote may differ from the model shown in the illustrations.
4
5
3
1 Press the remote start button on the transmitter to start the vehicle.*
2
Insert the key into the key slot,without pressing all the way.
You can now press the brake pedal, put the car in gear and drive off.
Enter the vehicle, while making sure the key fob is inside with you.
Enter the vehicle, while making sure the key fob is inside with you.
Press the Unlock button on the aftermarket remote.*
Ready to drive off
Press remote start
button*
Press Unlock button on
either remote*
Insert Key
Enter vehicle with key fob
Note: If the brake is not pressed within 60 seconds after the unlock, takeover become inactive. If the takeover is inactive, Remote Starter will stop the engine when the door opens
Note: If the brake is not pressed within 60 seconds after the unlock, takeover become inactive. If the takeover is inactive, Remote Starter will stop the engine when the door opens or when the brake is pressed.
Rev.: 20121101
Quick Reference GuideDBALL-VW02
© 2012 Directed. All rights reserved.
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
Press remote start
button*
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Exit vehicle with Smart Key
Pit Stop ModeThe Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
Press the button to remote start the vehicle.*The turn signal lights will flash once to indicate the vehicle is now in Pit Stop Mode.
The turn signal lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
Turn Signal Lights Error Codes
Flashes Diagnostic1 Runtime expired.2 Over-rev shutdown.3 Low or no RPM.4 Shut down without remote.5 Brake shutdown.6 Hood shutdown*.7 Remote Start Safety Override Switch ON.
*If your installation requires an aftermarket hood pin, 6 flashes can also mean Remote Start Safety Override Switch ON.
Note: If the brake is not pressed within 60 seconds after the unlock, takeover become inactive. If the takeover is inactive, Remote Starter will stop the engine when the door opens or when the brake is pressed.
Vehicle Takeover for PTS vehicles
* Your aftermarket remote may differ from the model shown in the illustrations.
4
3
1 Press the remote start button on the transmitter to start the vehicle.*
2
You can now press the brake pedal, put the car in gear and drive off.
Enter the vehicle
Press the Unlock button on theaftermarket remote.*
Ready to drive off
Press remote start
button*
Press Unlock button on
either remote*
Enter vehicle
Rev.: 20121101
Quick Reference GuideDBALL-VW02
© 2012 Directed. All rights reserved.
Runtime
The Runtime Reset feature allows the user to increase the runtime duration for a maximum of 10 minutes. This can only performed ONCE per remote start.
The runtime is equivalent to the amount set for the OEM remote starter, which is 10 minutes. A maximum of 2 remote starts can be performed between ignition cycles.
Runtime Reset
Remote Start Ready (RSR)Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
(Must be completed by the installer.)
Note: Additional fees may apply for the installation of the above features.
Additional Features
The following features are available with this product, but may not be compatible with your vehicle. Refer to your installation facility for more information.
Controlled Door Lock
3x OEM Lock Remote Start ActivationThis feature enables you to start/stop the vehicle using the OEM remote.
Press the OEM remote LOCK button three (3) times within three (3) seconds to start the vehicle. To stop the vehicle, press the LOCK button three (3) more times.
The OEM remote lock and unlock functions are inactive when the key is inserted into the ignition; therefore, the 3x OEM Lock Remote Start Activation feature cannot be used for idle mode.
Smart OEM Alarm Control
SmartStart Compatible
This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system:
Lock/ArmUnlock/DisarmRemote Car StarterTrunk ReleasePanicAux Channels
You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart!
But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more.
3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
Rev.: 20121101
Quick Reference GuideDBALL-VW02
© 2012 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote start.
Press & hold for 5 seconds to activate the trunk release (optional).
Press once, then to activate the AUX 1 output.*
Press 2 times, then to activate the AUX 2 output.
Press 3 times, then to activate the AUX 3 output.
Press once, then to reset the remote starter runtime.
List of Available Commands
x1 +
x3 +
x2 +
x1 +* This output is configurable. see your authorized installation center for more
information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Rev.: 20121101
Quick Reference GuideDBALL-VW02
© 2012 Directed. All rights reserved.