dball-dball2-tl2-rsr en ig cp20150706 · 06-07-2015 · 2 toyota sienna (smart key) 2011-2014...
TRANSCRIPT
Index
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
® Toyota and Lexus are registered trademarks and property of their respective companies.
Vehicle Application Guide..................................................................................................................................................OEM Remote Starter Detection.........................................................................................................................................
Installation TypesType 1a (with T-Harness)..................................................................................................................................................Type 1b (without T-Harness)............................................................................................................................................Wiring Reference Chart - Type 1.......................................................................................................................................Type 2a (with T-Harness)..................................................................................................................................................Type 2b (without T-Harness)............................................................................................................................................Wiring Reference Chart - Type 2.......................................................................................................................................Type 3a (with T-Harness)..................................................................................................................................................Type 3b (without T-Harness)............................................................................................................................................Wiring Reference Chart - Type 3.......................................................................................................................................SmartStart/XL202 Installation Notes.................................................................................................................................
ProgrammingModule Programming........................................................................................................................................................Module Reset & Hard Reset..............................................................................................................................................Features & Options List.....................................................................................................................................................Features Programming......................................................................................................................................................
LED Diagnostics & Troubleshooting..................................................................................................................................Parking Light Error Codes.................................................................................................................................................Limited One-Year Consumer Warranty..............................................................................................................................Quick Reference Guide.....................................................................................................................................................
0203
04050607080910111213
14151516
17171819
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Important!This product is NOT compatible with vehicles equipped with a manual transmission.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a Plug & Play (TLTH2) T-Harness (Optional). This solution offers three (3) configuration options to control your system; 3x OEM Lock Remote Start Activation, RF Kit or SmartStart (all sold separately).
Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how to use various features offered with this product.
SmartStart CompatibleSmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Vehicle Application GuidePage 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
Vehicles
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
AV
-Auto
Headla
mp
Shuto
ff
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-H
atc
hG
lass
Rele
ase
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
EIP
S
RS
-3x
LO
CK
ST
AR
T(S
tart
contr
ol
usin
gO
EM
Rem
ote
)
RS
-3x
LO
CK
ST
OP
(Sto
pcontr
ol
usin
gO
EM
Rem
ote
)
RS
-Rem
ote
Sta
rtR
eady
RS
-Sm
art
Sta
rt
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Driver
Door
Pin
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
SS
-Facto
ryA
larm
Trigger
Monito
ring
ST
-Bra
ke
Sta
tus
(footbra
ke)
ST
-Igniti
on
Sta
tus
Lexus
CT 200h (Smart Key) 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • • •
GX 460 (Smart Key) 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • •
HS 250h (Smart Key) 3 3 3 • • • • • • • • • • • • • • • • • • • • •
RX 350 (Smart Key) 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • •
RX 450h (Smart Key) 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • •
Toyota 15 14 13 12 11 10 09
4Runner (Smart Key) 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • •
Prius (Smart Key) 3 3 3 3 3 • • • • • • • • • • • • • • • • • • • • • •
Prius v (Smart Key) 3 3 3 3 • • • • • • • • • • • • • • • • • • • • •
Sienna (Smart Key) 2 2 2 2 • • • • • • • • • • • • • • • • • • • • • • •
Venza (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • •
Legend:
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
EIPS: Engine Idle Protection System
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Note: Keyless and Smart Key will remain functional during remote start.
Warning!
• If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing the DBALL otherwise it will not program.
• No takeover feature is available on Push-to-Start vehicles.
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 3
If the Vehicle is Equipped with an OEM Remote Starter
How to Know if the Vehicle is Equipped with an OEM Remote Starter
Locating the OEM Remote Starter
Installation
TypeVehicle
OEM Remote Starter & Connectors
Location
1 Toyota Venza Push-to-start 2009- 2014 Behind glove box
2 Lexus RX 450h 2010-2015 Behind glove box
2 Lexus RX 350 2010-2015 Behind glove box
2 Toyota 4Runner (Smart Key) 2010-2014 Behind glove box & Passenger kick panel
2 Toyota Sienna (Smart Key) 2011-2014 Behind glove box & Passenger kick panel
3 Lexus HS 250h 2010-2012 Behind glove box
3 Toyota Prius 2010-2014 Under dash panel & Driver kick panel
3 Lexus CT 200h 2011-2015 Behind glove box
3 Lexus GX 460 2010-2015 Behind glove box
3 Toyota Prius V 2012-2015 Behind glove box
If the vehicle is equipped with an OEM remote starter, the DBALL LED will start flashing orange to indicate its detection. To skip bypass and use convenience only, press the programming button 5 times.* The reason for this is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish to use DBALL to control the remote start sequence, the factory remote starter must be disconnected before programming the DBALL as both modules cannot coexist.
* The DBALL LED turns ON solid orange for 3 seconds after programming or power up to indicate the bypass is not active. Refer to LED Diagnostics & Troubleshooting section for more information.
OEM Remote Starter Detection
1- An “ENGINE STARTER” sticker should be on the
2- Remote start the OEM remote starter:Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds.
The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 20 seconds.
ENGINESTARTER
x2 &Press & Holdfor 3 seconds
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
BRX:Black,pin 23
Main body ECUBack side
(-) Parking Lights: Red, pin 23
D50White connector
D50D49
White connectorD49
BTX:Blue,
pin 22
Page 4
[1] (-) SLP Output: Yellow
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
[1] SLP: Violet, pin 4
D17 - Steering LockBlack connector
1235 47 6
Installation Type 1a (with T-Harness)
[2] EIPS to Horn: pin 8
10 1112987
1 2 3 4 5 6
Horn - Black connector (at the bottom of steering column)
[2] (-) EIPS Fail Output: Black/White: 1
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
(-) Parking Lights Output: Red/Black: 4
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] SLP: Steering Lock Actuator Position Signal.
[2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
10
14
12
10
DBALL
RF
Prog. Button
LED
4
14
12
2
For the 12-pin and 10-pinconnectors, use the harnesses that are provided with the DBALL.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
13 15 16 18
23 26
14 17
24 25
5 6 7 8 9 104321
12 201911
22 282721 22 23
2322 2618
107
25
13 14 16 178
21
9 11 12 15
24
1 2 3 4 5 6
2319 20
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
1 8
169
HS CAN Low, pin 14 (+)12V, pin 16
HS CAN High, pin 6(-) Ground, pin 4
Page 5
OBDIIDiagnostic Connector
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Installation Type 1b (without T-Harness)
(-) Ground: Black: 14
(+) 12V: Red: 13
[2] (-) EIPS Fail Output: Black/White: 1
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] SLP: Steering Lock Actuator Position Signal.
[2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
[1] (-) SLP Output: Yellow/Red: 11
(-) Ground: Brown/Red: 12
10
14
12
10
DBALL
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
Main body ECUBack side
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
2322 2618
107
25
13 14 16 178
21
9 11 12 15
24
1 2 3 4 5 6
2319 20
BRX:Black,pin 23
D49White connector
BTX:Blue,
pin 22
13 15 16 18
23 26
14 17
24 25
5 6 7 8 9 104321
12 201911
22 282721 22 23
(-) Parking Lights: Red, pin 23
D50White connector
D50 D49
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
[1] SLP: Violet, pin 4
D17 - Steering LockBlack connector
1235 47 6
[2] EIPS to Horn: pin 8
10 1112987
1 2 3 4 5 6
Horn - Black connector (at the bottom of steering column)
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Vehicles Function Connector Pin Wire
CAN High D1 (OBDII) 6 Yellow
CAN Low D1 (OBDII) 14 White
BRX J 1 Black
BTX J 2 Blue
Push-to-Start D13 7 Blue
SLP* D17 4 Violet
Horn D18 8 Yellow
Ground D1 (OBDII) 4 Black
CAN High D1 (OBDII) 6 Yellow
CAN Low D1 (OBDII) 14 White
BRX D49 23 Black
BTX D49 22 Blue
Push-to-Start D13 7 Blue
SLP* D17 4 Violet
Horn D18 8 Yellow
Ground D1 (OBDII) 4 Black
*SLP: Steering Lock actuator position signal
Toyota Venza
2009- 2012
Push-to-Start
Toyota Venza
2013-2014
Push-to-Start
Page 6
Vehicle Wiring Reference Chart - Type 1
Locating Key Components in the Vehicle
WARNING- No takeover feature is available. See Quick Reference Guide (QRG) at the end of this guide.- To remote start the engine, all doors must be closed, including rear hatch.
Black connector at steering lockToyota Venza: conn. D17
Push-to-start buttonToyota Venza 2013: conn. J
Main Body ECUToyota Venza: conn. D49, D50
Diagnostic connectorToyota Venza: conn. D1
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 7
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
Installation Type 2a (with T-Harness)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
(-) Parking Lights Output: Red/Black: 4
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] SLP: Steering Lock Actuator Position Signal.
[2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
10
14
12
10
DBALL
RF
Prog. Button
LED
4
14
12
2
For the 12-pin and 10-pinconnectors, use the harnesses that are provided with the DBALL.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
[2] (-) EIPS Fail Output: Black/White: 1
[1] (-) SLP Output: Yellow
BRX, pin 4
BTX, pin 16
MainBodyECU
Whiteconnector(wire side view)
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
(-) Parking lights, pin 30
30
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
[1] SLP: Violet, pin 4
D17 - Steering LockBlack connector
1235 47 6
[2] EIPS to Horn: pin 8
10 1112987
1 2 3 4 5 6
Horn - Black connector (at the bottom of steering column)
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 8
Installation Type 2b (without T-Harness)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] SLP: Steering Lock Actuator Position Signal.
[2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
10
14
12
10
DBALL
RF
Prog. Button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
MainBodyECU
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(-) Ground: Black: 14
(+) 12V: Red: 13
[2] (-) EIPS Fail Output: Black/White: 1
[1] (-) SLP Output: Yellow/Red: 11
(-) Ground: Brown/Red: 12
BRX, pin 4
BTX, pin 16
Whiteconnector(wire side view)
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
[1] SLP: Violet, pin 4
D17 - Steering LockBlack connector
1235 47 6
[2] EIPS to Horn: pin 8
10 1112987
1 2 3 4 5 6
Horn - Black connector (at the bottom of steering column)
1 8
169
HS CAN Low, pin 14 (+)12V, pin 16
HS CAN High, pin 6(-) Ground, pin 4
OBDIIDiagnostic Connector
(-) Parking lights, pin 30
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Locating Key Components in the Vehicle
Page 9
Diagnostic connectorLexus GX460: conn. G37Lexus RX350: conn. F17Lexus RX450h: conn. F17Toyota 4Runner: conn. F13Toyota Sienna: conn. D16
Main Body ECULexus GX460: conn. G47Lexus RX350: conn. F13Lexus RX450h: conn. F13Toyota 4Runner: conn. F9Toyota Sienna: conn. D13 Push-to-start button
Lexus GX460: conn. G24Lexus RX350: conn. F22Lexus RX450h: conn. F22Toyota 4Runner: conn. F71Toyota Sienna: conn. D33
Black connector at steering lockLexus GX460: conn. G23Lexus RX350: conn. F37Lexus RX450h: conn. F37Toyota 4Runner: conn. F68Toyota Sienna: conn. D29
WARNING- No takeover feature is available. See Quick Reference Guide (QRG) at the end of this guide.- To remote start the engine, all doors must be closed, including rear hatch.
Vehicle Wiring Reference Chart - Type 2
Function Connector Pin Wire Function Connector Pin Wire
CAN High G37 6 Red CAN High F13 6 Violet
Can Low G37 14 White CAN Low F13 14 White
BRX G47 4 Red BRX F9 4 Gray
BTX G47 16 Green BTX F9 16 White
Parking Light G47 30 White Parking Light F9 30 Red
Push-to-Start G24 7 Lt. Green Push-to-Start F71 7 Lt. Green
SLP* G23 4 Lt. Blue SLP* F68 4 Lt. BlueHorn G28 8 Green Horn F23 8 Gray12V 2K 1 Black 12V 2E 1 Black
CAN High F17 6 Violet CAN High D16 6 Red
CAN Low F17 14 Red CAN Low D16 14 White
BRX F13 4 Pink BRX D13 4 Black
BTX F13 16 Lt. Green BTX D13 16 Blue
Parking Light F13 30 Violet Parking Light D13 30 Yellow
Push-to-Start F22 7 Lt. Green Push-to-Start D33 7 Blue
SLP* F37 4 Green SLP* D29 4 Green
Horn F40 8 White Horn D21 8 Green12V 2K 1 White 12V 2K 1 Red
CAN High F17 6 Violet * SLP: Steering Lock actuator position signal.
CAN Low F17 14 Red
BRX F13 4 Pink
BTX F13 16 Lt. Green
Parking Light F13 30 Violet
Push-to-Start F22 7 Lt. Green
SLP* F37 4 Green
Horn F40 8 White
12V 2K 1 Black
Lexus
RX 350
2010-2015
Lexus
GX 460
2010-2015
Toyota Sienna
Smart Key
2011-2014
Lexus RX
450h
2010-2015
Toyota 4Runner
Smart Key
2010-2014
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 10
Installation Type 3a (with T-Harness)
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
10
14
12
10
DBALL
RF
Programming button
LED
4
14
12
2
For the 12-pin and 10-pinconnectors, use the harnesses that are provided with the DBALL.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
OBDII16-pin Diagnostic Connector
(vehicle side)
TLTH2(optional)
[2] (-) EIPS Fail Output: Black/White: 1
MainBodyECU
BRX pin 4
BTX pin 16
Whiteconnector(wire side view)
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
(-) Parking lights, pin 30
Lexus HS250h 2010-2012
Toyota Prius 2010-2013
Toyota Prius V 2012-2014
[2] EIPS to Horn :pin 8
[2] EIPS to Horn :pin 9
10 1112987
1 2 3 4 5 6
111098
1 2 3 4 5 6 7
12 1314OR
Horn - Black Connector (at the bottom of steering column)
Lexus CT200h 2011
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 11
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Installation Type 3b (without T-Harness)
[1] (-) EIPS Fail Output: Black/White: 1
(-) Ground: Black: 14
(+) 12V: Red: 13
Important!The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
[1] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated.
10
14
12
10
DBALL
RF
Programming button
LED
4
14
12
2
You can connect to either a XL202 RFTD OR a SmartStart module.
Refer to the SmartStart/XL202 Installation Notes for more information.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety Override Switch
Note: Hood pin only required on vehicle not equipped with a factory hood pin.
BRX: Yellow/Black: 10
BTX: Orange/Black: 11
(-) Push-to-Start Output: Green/Black: 2
(-) Parking Lights Output: Red/Black: 4
MainBodyECU
BRX pin 4
BTX pin 16
Whiteconnector
1 72 83
6
9 21
22
25
10
13
23
26
11
14
29
24
27
12
15
18
20
19
4 16 28
30
1 8
169
HS CAN Low: pin 14 (+)12V: pin 16
HS CAN High: pin 6(-) Ground: pin 4
OBDIIDiagnostic Connector
(-) Push-to-start: pin 7
ENGINESTARTSTOP
BlackConnector
Connection required only if Pit-Stop / Idle mode or EIPS is desired. (see details on the next page).
1 3 4 5 7
12 1411108
2
9
6
13
7
(-) Parking lights, pin 30
Lexus HS250h 2010-2012
Toyota Prius 2010-2013
Toyota Prius V 2012-2014
[2] EIPS to Horn :pin 8
[2] EIPS to Horn :pin 9
10 1112987
1 2 3 4 5 6
111098
1 2 3 4 5 6 7
12 1314OR
Horn - Black Connector (at the bottom of steering column)
Lexus CT200h 2011
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Vehicles Function Connector Pin Wire
CAN High H44 (OBDII) 6 Red
CAN Low H44 (OBDII) 14 White
BRX H16 4 Yellow
BTX H16 16 Blue
Push-to-Start H78 7 BlackHorn H30 9 Yellow
12V H44 (OBDII) 4 White
CAN High F11 (OBDII) 6 Green
CAN Low F11 (OBDII) 14 Black
BRX F9 4 Yellow
BTX F9 16 Blue
Push-to-Start F2 7 BlueHorn F19 8 White
12V F11 (OBDII) 4 Black
CAN High L61 (OBDII) 6 White
CAN Low L61 (OBDII) 14 Yellow
BRX L7 4 Violet
BTX L7 16 Green
Push-to-Start L43 7 Black
Horn L52 8 Yellow
12V L61 (OBDII) 4 White
CAN High OBDII 6 Black
CAN Low OBDII 14 White
BRX (Body ECU) L7 4 Violet
BTX (Body ECU) L7 16 Green
Push-to-Start L43 7 Black
Light (Body ECU) L7 30 Yellow
Horn L52 8 Yellow
12V 2E 1 White
Lexus HS 250h
2010-2012
Toyota
Prius V 2013-2015
Lexus CT 200h
2011-2015
Toyota Prius
2010-2014
& Toyota Prius V
2012
Page 12
Locating Key Components in the Vehicle
Diagnostic connectorLexus HS250h: conn. F11Toyota Prius: conn. L61
Main Body ECULexus HS250h: conn. 2E, F9Toyota Prius: conn. 2E, L7
Push-to-start buttonLexus HS250h: conn. F2Toyota Prius: conn. L43
WARNING- No takeover feature is available. See Quick Reference Guide (QRG) at the end of this guide.- To remote start the engine, all doors must be closed, including rear hatch.
Vehicle Wiring Reference Chart - Type 3
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
An
ten
na
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system; 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.
Configuration Wires (Gray & White)Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins, not usedCABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL package.2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart/XL202 Installation Notes
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
LED
Prog.Button
D2D (4 pins, white)
4 pins
2 pins, not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
Page 13
DBALL/DBALL2
DBALL/DBALL2
DBALL/DBALL2
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 14
Module Programming
3 Press the vehicle PTS button once (1) to turn the ignition OFF. Wait for the LED to turn OFF. DBALL is now programmed.
Off
ENGINESTARTSTOP
PUSH x2
Solid Greenx3 secs.
Solid Red
& &
&ENGINESTARTSTOP
PUSH x1
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
2
Press the vehicle Push-to-Start (PTS) button twice (2) to turn the ignition ON. Wait for the LED to turn ON solid green for three (3) seconds*.
* If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to LED Diagnostics & Troubleshooting section for more information.
You have successfully completed the module programming sequence.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select one of the available install options (config for RSR, RXT or Standard install), and follow the instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.
1 10-pinD2D
st1
12-pin14-pin
nd2
rd3
&Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to DBALL, then wait until the LED turns ON solid red.
10-pinD2D
XL202
10-pinD2DSmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 15
Module Reset
1If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
2
Solid
&Release
3 Release the programming button. The LED turns ON solid red.
Hard Reset
2 & &
1
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
Solid Release Solid
Solid Flashes
&Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 16
Feature and Option List
Feat. Operation Flashes/Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at
the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle
in the remote start sequence, only when required. The reason for this is, factory alarm control must often be
done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the
horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to
detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so
that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active,
will work perfectly with this option and will make it invisible to the user.
* Default Option
Smart OEM Alarm
Control3
RFTD Output Type1
Unlock Driver Priority2
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options such as EIPS and RSR; however, manual configuration of the features is possible using the information on this page.
To enter feature programming routine Turn the ignition ON, then OFF. Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing
the DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature Press and release the programming button a number of times to advance from the current feature to the next desired feature. The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed Other features can be programmed. The feature programming can be exited.
Exiting feature programming No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
Page 17
LED Status Description TroubleshootingProgramming the Module
Off Module has no power.Make sure the D2D harness is connected or that the 12 Volt is present between the
red and black wires. If the 12 Volt is present, the module may be defective.
Solid RedWaiting to begin the
programming sequence.Refer to the wiring diagram to make sure that all the connections are correct.
Flashes OrangeOEM remote starter
detected.
If the user wants to use the module as a convenience only, he should skip bypass by
pressing the programming button 5 times. However, if the user wants to use the
module as a remote starter, he should disconnect the OEM remote starter and
repeat the programming sequence.
Solid Green x3
seconds
Module has been
successfully programmed.Normal operation.
Solid Orange x3
seconds
Module was successfully
programmed without bypass
(convenience only).
Normal operation. An OEM remote starter was detected (convenience mode only). If
the user wants to use the module as a remote starter, he should disconnect the
OEM remote starter and repeat the programming sequence, by doing a short reset.
Module Programming - Error Codes
Flashes Red x5 ISO 1 not detected.Yellow/Black did not detect the expected signal. Refer to the wiring diagram to make
the right connections.
Flashes Red x6 ISO 2 not detected.Orange/Black did not detect the expected signal. Refer to the wiring diagram to make
the right connections.
Active Ground While Running
Flashes GreenGROUND OUT ON (GWR)
command received.
Otherwise, the Ground While Running (status) signal was lost or was never received
by the module. Commands can come from RF or D2D.
Flashes Red &
Orange
IGNITION ON command
received.
Flashes Green
Quickly
START ON command
received.
External Commands
Flashes Orange x1 Lock command received.
Flashes Orange x2 Unlock command received.
Flashes Orange x3 Trunk command received.
Flashes Orange x4 AUX1 command received.
Flashes Orange x5 AUX2 command received.
If the bypass module fails to flash, it means the module did not receive the signal.
Commands can come from RF or D2D.
LED Diagnostics and Troubleshooting
Flashes Diagnostic
1 Runtime expired.
2 Over-rev shutdown.
3 Low/No RPM.
4 Transmitter shutdown.
5 Brake shutdown.
6 Hood shutdown/Remote start safety override switch is ON*.
7 Remote start safety override switch is ON*.
The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.
* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.
Parking Light Error Codes
Platform: DBALL/DBALL2Firmware: TL2 Remote Start Ready (RSR) Installation
© 2015 Directed. All rights reserved.
Rev.: 20150706
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited One Year Consumer WarrantyPage 18
Qu
ick R
efe
ren
ce G
uid
eD
BA
LL
/DB
AL
L2
-TL
2 R
em
ote
Sta
rt R
ea
dy
(R
SR
) In
sta
lla
tio
n
© 2
01
5 D
ire
cte
d. A
ll rig
hts
re
serv
ed
.
1 2 3
Sto
p the v
ehic
le in
a s
afe
park
ing s
pot
and p
ut th
e g
ear
in P
ark
(P
).
Pre
ss
rem
ote
sta
rt
bu
tto
n*
* Y
ou
r a
fte
rmark
et re
mote
may
diff
er
from
the m
odel s
how
n in
the il
lust
ratio
ns.
Sto
p &
pu
t veh
icle
in
Park
(P
)
P&
Fla
sh
es
ENGIN
ESTART
STOP
&
HO
LD
Exit
veh
icle
wit
h
Sm
art
Key
Pit
Sto
p M
od
e
The
Pit
Sto
p M
ode featu
re is
pra
ctic
al w
hen y
ou n
eed to s
top a
nd r
un a
n e
rrand,
but w
ish
to
keep the e
ngin
e r
unnin
g.
No
te:
We r
eco
mm
end that yo
u a
lways
lock
th
e d
oors
o
f yo
ur
vehic
le w
hen le
avi
ng it
unattended.
It is
now
safe
to le
ave
the e
ngin
e r
unnin
g a
nd e
xit th
e
vehic
le w
ith the f
act
ory
rem
ote
in h
and.
Pre
ss the b
utton
to r
em
ote
sta
rt the v
ehic
le.*
The P
TS
button
will
fla
sh o
nce
to
indic
ate
the v
eh
icle
is n
ow
in P
it S
top
Mode.
Rem
ote
Sta
rt R
ea
dy (
RS
R)
Rem
ote
Sta
rt R
eady
(RS
R)
is a
funct
ion t
hat
enable
s th
e in
terf
ace
m
odule
to r
em
ote
sta
rt t
he v
ehic
le c
om
ple
tely
on it
s ow
n.
Conse
quently
, th
ere
is n
o n
eed f
or
an a
fterm
ark
et
or
an O
EM
rem
ote
st
art
er
in o
rder
to s
tart
the v
ehic
le f
rom
a d
ista
nce
.
3x O
EM
Lo
ck R
em
ote
Sta
rt A
cti
vati
on
This
solu
tion in
cludes
the o
ptio
n t
o r
em
ote
sta
rt y
our
vehic
le b
y pre
ssin
g t
he L
ock
button 3
tim
es
conse
cutiv
ely
. If
your
vehic
le a
llow
s th
e O
EM
rem
ote
to r
em
ain
act
ive w
hile
the e
ngin
e is
runnin
g,
you m
ay
shut
dow
n y
our
rem
ote
sta
rter
by
pre
ssin
g the L
ock
button 3
tim
es
once
more
.
Note
: T
he r
ange o
ffere
d b
y O
EM
rem
ote
s is
lim
ited a
nd t
ypic
ally
requires
you t
o b
e
with
in e
yesi
ght of th
e v
ehic
le t
o c
ontr
ol i
t.
Qu
ick R
efe
ren
ce G
uid
eD
BA
LL
/DB
AL
L2
-TL
2 R
em
ote
Sta
rt R
ea
dy
(R
SR
) In
sta
lla
tio
n
© 2
01
5 D
ire
cte
d. A
ll rig
hts
re
serv
ed
.
Sm
art
Sta
rt C
om
pati
ble
This
sys
tem
is c
om
patib
le w
ith D
irect
ed S
mart
Sta
rt 3
.0.
For
a c
om
ple
te li
st o
f su
pport
ed f
eatu
res,
ple
ase
vis
it w
ww
.mys
mart
start
.com
.
Wh
at
is S
mart
Sta
rt?
Now
you c
an r
em
ote
sta
rt,
lock
and u
nlo
ck y
our
car
just
by
push
ing a
butt
on o
n
your
smart
phone; usi
ng
the S
mart
Sta
rt A
pp f
rom
Direct
ed,
the le
ader
in v
ehic
le
secu
rity
and r
em
ote
sta
rt. T
he s
imple
gra
phic
al i
nte
rface
giv
es
you c
ontr
ol o
ver
the
follo
win
g featu
res
of yo
ur
inst
alle
d r
em
ote
sta
rt o
r se
curity
with
rem
ote
sta
rt s
yste
m:
L
ock
/Arm
U
nlo
ck/D
isarm
R
em
ote
Car
Sta
rter
T
runk
Rele
ase
P
anic
A
ux
Channels
You c
an a
lso c
ontr
ol m
ulti
ple
vehic
les
– g
reat
for
fam
ilies
– a
nd a
ssig
n m
ore
than
one u
ser
to c
ontr
ol a
vehic
le.
It's
easy
with
Sm
art
Sta
rt!
But, this
is o
nly
the b
egin
nin
g!
Sm
art
Sta
rt is
loaded w
ith a
dditi
onal f
eatu
res
incl
udin
g G
PS
tra
ckin
g,
Sm
art
Sch
edule
, ve
hic
le s
tatu
s, r
oadsi
de a
ssis
tance
, hom
e
contr
ol,
park
ed c
ar
finde
r and m
ore
.
3.0
enable
s a "
Clo
ud-C
onnect
ed C
ar"
like
neve
r befo
re,
pro
vidin
g a
n e
ntir
ely
new
le
vel o
f 2-w
ay
inte
ract
ion w
ith y
our
vehic
le.
Connect
ivity
is m
anaged t
hro
ugh t
he
Direct
ed C
loud S
erv
ices
(DC
S)
netw
ork
linki
ng c
ar,
app,
end u
ser,
and t
he I
nte
rnet.
For
more
info
rmatio
n, vi
sit
ww
w.m
ysm
art
start
.com
.
Bu
tto
n(s
)A
cti
on
s
Pre
ss &
hold
for
1 s
econd t
o lock.
Pre
ss &
hold
for
1 s
econd t
o u
nlo
ck.
Pre
ss &
hold
for
1 s
econd t
o r
em
ote
sta
rt.
Pre
ss &
hold
for
5 s
econds t
o a
ctiva
te
the t
runk r
ele
ase (
optional).
Pre
ss
once,
then
to a
ctiva
te t
he
rear
hatc
h/t
ail
gla
ss r
ele
ase (
optional).*
Pre
ss
3 t
imes,
then
to a
ctiva
te
the p
anic
mode.
Pre
ss
once,
then
to r
eset
the
rem
ote
sta
rter
runtim
e.
Lis
t o
f A
vailab
le C
om
man
ds
x1 +
x3 +
x1 +
* T
his
ou
tput is
config
ura
ble
. se
e y
our
auth
orize
d in
stalla
tion c
ente
r fo
r m
ore
in
form
atio
n.
Note
th
at th
e in
form
atio
n b
elo
w is
for
Vip
er,
Clif
ford
and P
ython m
odels
. Ic
ons
and
com
ma
nd
s m
ay
diff
er
dependin
g o
n the r
em
ote
bra
nd a
nd m
odel p
urc
hase
d. R
efe
r to
yo
ur
au
thorize
d in
stalla
tion c
ente
r fo
r m
ore
info
rmatio
n.
Qu
ick R
efe
ren
ce G
uid
eD
BA
LL
/DB
AL
L2
-TL
2 R
em
ote
Sta
rt R
ea
dy
(R
SR
) In
sta
lla
tio
n
© 2
01
5 D
ire
cte
d. A
ll rig
hts
re
serv
ed
.
En
gin
e Id
le P
rote
cti
on
Syste
m (
EIP
S)
Vehic
les
equip
ped w
ith R
FID
-typ
e P
ush
-to-S
tart
igniti
on s
yste
ms
work
by
dete
ctin
g
a p
roxi
mity
key
in the v
eh
icle
. T
hey
will
run in
defin
itely
if the k
ey
is r
em
ove
d, w
hic
h
could
po
tentia
lly le
ad u
sers
to e
xitin
g the v
ehic
le w
hile
the e
ngin
e is
stil
l runnin
g
and
th
e c
ar
is le
ft id
ling o
n it
s ow
n in
a g
ara
ge o
r a c
on
fined s
pace
.
To m
itig
ate
ris
k, w
e h
ave
desi
gned a
featu
re that is
no
w a
vaila
ble
on the D
BA
LL
. It
will
de
tect
the p
rese
nce
of th
e R
FID
fob in
the v
ehic
le,
thro
ugh the C
AN
bus.
If le
ft
idlin
g fo
r m
ore
than the p
re-d
efin
ed r
untim
e (
i.e. 1 to 5
min
ute
s) w
ithout dete
ctin
g
the fo
b,
DB
AL
L w
ill s
end
a s
ignal t
o the v
ehic
le in
ord
er
to s
hut off the e
ngin
e.
EIP
S (
En
gin
e Idle
Pro
tect
ion S
yste
m)
will
:
N
otif
y th
e u
ser
about th
e id
ling e
ngin
e b
y so
undin
g the h
orn
with
a s
eries
of sh
ort
bee
ps.
S
hu
t d
ow
n the e
ngin
e a
fter
a p
re-d
efin
ed p
eriod o
f tim
e (
i.e. 1 to 5
min
ute
s).
EIP
S is
config
ure
d u
sing X
pre
ssV
IP. T
he follo
win
g w
indow
is d
ispla
yed w
heneve
r a D
BA
LL m
odule
is fla
shed.
If
th
e e
ngin
e fails
to s
hu
t dow
n d
ue to s
om
e m
alfu
nct
ion,
EIP
S w
ill g
o in
to a
larm
m
od
e a
nd w
ill n
otif
y th
e u
ser
by
all
means
poss
ible
(e.g
. horn
or
sire
n).
Act
ivatin
g/d
eact
ivatin
g E
IPS
:
To
act
ivate
EIP
S, re
mo
ve a
ll ke
ys f
rom
the v
ehic
le a
nd c
lose
all
doors
while
the
engin
e is
runnin
g.
To
deact
ivate
EIP
S, do
one o
f th
e f
ollo
win
g a
ctio
ns:
O
pen o
ne o
f th
e d
oors
.
Rem
ote
sta
rt the v
ehic
le.
T
urn
the e
ngin
e o
ff.
D
rive
the v
ehic
le.*
* T
he E
IPS
featu
re is
dis
able
d if
the v
ehic
le is
in m
otio
n s
o t
here
is n
o r
isk
that
the
vehic
le w
ill s
hut off w
hile
drivi
ng,
regard
less
of
the f
ob b
ein
g p
rese
nt
in t
he v
ehic
le
or
not.
No
tes