date my home light and automation. 2 division appareillage et système résidentiels apartment villa...

Date

MY HOME LIGHT AND AUTOMATION

2Division Appareillage et Système Résidentiels

ApartmentVilla

My home SCS bus system was designed with:system dimension and features for houses (residential)installation method close to the traditional installationaesthetic integrated with wd and des offer

Introduction


L

System compositionNOT ONE GENERAL CENTRAL UNIT

NO CENTRALIZED CONFIGURATION

Power supplyControls

N

Actuators

Loads

27V BUS


SCS bus characteristics27V D.C. NOT POLARIZED POWER SUPPLY AND DIGITAL DATA

Sender

Receiver

Information0 1 0 1 0 1 0 1 0 1 0 1

L230V

N

System composition


Catalogue

USER INTERFACES

ACTUATORS(ON/OFF)

DIMMERS

INTERFACES

ACCESSORIES


SOME MH DEVICE ARE IN COMMON WITH LM SYSTEM.

FOR THIS REASON YOU CAN USE THE LM CONFIGURATION RULES AND SYSTEM LIMITS.

Catalogue


Incandescent

Discharge

Halogen

Fluorescent

LED

Motors ON/OFF

Motors up/downright/left

Loads typology driven: most of the typology

Catalogue


Configuration


Relating to different products or different choices there are 2 main types of configuration:

PHYSICAL CONFIGURATION USING JUMPERSGreen for the address and the blue ones are for functioning mode.

VIRTUAL CONFIGURATIONAvailable ONLY for automation and temperature control system. It is a

SW able to configure the devices through the gateway (MH200N, F454).

Configuration


3° Level

Project & Download:ONLY for Lighting Management.

1° Level

PhysicalUsing jumpers.

81 addresses

A=0-9PL=1-9

Configuration

2° Level

175 addresses

A=0-10PL=0-15

Virtual


Actuator addressing mode

The addresses of the actuator depending by the configuration of the site A and PL.

For each area it is possible to set a max of 9 PL for each Area (max 9).In order to link an actuator to a group, it is necessary to add a jumper in the site G (group).

Socket Jumpers Notes

[A] AreaActuator address

From11 to 99Numeric jumpers 1÷9

[PL] Light point

[M] Mode From 1÷4 Numeric and blue jumpers 1÷9 [G] Group Group address Numeric Jumpers from 1 to 9

Physical configuration


Addressing and control type

Also the control devices have the configuration sockets A and PL in order to set the receiver of the messages (actuators).




POINT -POINT CONTROLDirect control to one actuator identified by a “room number” and a “light point number”.

ROOM CONTROLDirect control to all the actuatorsidentified by the same room number (site A).



GROUP CONTROLDirect control to all the actuatorswhich perform particular functionseven if they belong to differentrooms and are identified by the same“group number”.



GENERAL CONTROLDirect control to all the system actuators


CONFIGURATION EXAMPLE



The functioning mode



The blue jumpers (including also some numbers) are used for the mode of work.



Controls operation modes

Light functioning modes:

ON timed command

ON command

OFF command

Pushbutton command

ON / OFF command

Automatism functioning modes:

UP / DOWN bistable command

UP / DOWN monostable command

Jumpers

PUL

ON

OFF

O/I

M

1-8




CONTROLS for Scheduler


Enable

Disable

Enable/disable

Timed ON 2 sec - 10 min

Blinking (from 0,5 to 5 sec)

Set the adjustment level (dimmer) (from 10 to 90 %)

Scenario recall (from 1 to 9)

SOFT START and SOFT STOP

Recall and program of the scenario module (from 1 to 16)

Door lock control

Sound diffusion control

Timed ON (from 5 sec to 99 min 45 sec)

Auxiliary input management

The “SPEcial” functioning modality



Using the Virtual Configuration , there are the same configuration rules of the physical one, but there are also some improvement:

Example: F411/4

Physical configuration Virtual configuration

APL1PL2PL3PL4M

A1PL1M1

A2PL2M2

A3PL3M3

A4PL4M4

One area for all the PL.Also the mode of work is

in commonEach PL can became independent from the

others

Virtual configuration


PC Connections Gateway Systems

Web Server - F454

Scheduler- MH200N

Suitcase 3504 o 3503N

Ethe

rnet

cab

le



With devices with ID and VIRT labels


Devices description

Reference number

Configuration


Basic scenarios configuration

EASY SCENARIOS WITH LIGHTS AND MOTORS

4 scenarios per Unit (command)16 scenarios per DIN module (memory)Configure the device (physical-virtual)Customizable by the end-user (push & learn)

Easy to set-upPush & Learn

Modulo scenari.wmv

Scenario module

4 scenarios command


Memory module

SAVE THE SYSTEM STATE IN BLACK-OUT SITUATION

• It needs an A/PL address• To save address it can be used in area 0

A=PL=

• 1 module for every system

(phisical extension included)

PL

A

1 to 9

0

Memory module

Easy to set-upPush & Learn

Modulo memoria.wmv


INSTALLATION RULES AND

LIMITS


System limits

DISTANCE

ABSORPTION

ADDRESSES LOGICAL LIMITS

PHYSICAL LIMITS

Installation rules and limits


Free BUS cabling topology

Star connections Free connection

Just one rule: no closed ring!


PHYSICAL LIMITS


Power supply Actuator Control

250m MAX 500m MAX


PHYSICAL LIMITS


9 Areas

9 PL for every area

9 x 9 = 81 addresses

LOGICAL LIMITS


Using physical configuration

9 Groups


11 Areas

16 PL for every area

(16 x 11)- 1 = 175 addresses

LOGICAL LIMITS


The address 00 doesn’t exist

Using virtual configuration

255 Groups

date my home light and automation. 2 division appareillage et système résidentiels apartment villa...

Documents