dao level 3 certificate in militray engineering · 2018. 5. 2. · dao level 3 certificate in...
TRANSCRIPT
Qualification Handbook
DAO Level 3 Certificate in Military Engineering (Armoured) Titan and Trojan crew supervision
QN: 603/3232/3
2
The Qualification
Overall Objective for the Qualifications
This handbook relates to the following qualification:
DAO Level 3 Certificate in Military Engineering (Armoured) Titan and Trojan crew
supervision
Pre-entry Requirements
Learners are required to have completed the Class ME (Armd) Class 0-2 course, must be
fully qualified AFV crewman and hold full category H driving licence
Unit Content and Rules of Combination
This qualification is made up of a total of 6 mandatory units and no optional units. To be
awarded this qualification the candidate must achieve a total of 13 credits as shown in the
table below.
Unit
number
Unit of assessment Level GLH TQT Credit
value
L/617/0309 Supervise Titan Operation and associated Equipment
3 25 30 3
L/617/0312 Supervise Titan Crew 3 16 19 2
R/617/0313 Supervise Trojan Operation and associated Equipment
3 26 30 3
D/617/0315 Supervise Trojan Crew 3 16 19 2
H/617/0316 Supervise Trojan and Titan AFV maintenance tasks
3 10 19 2
K/617/0317 Carry out emergency procedures and communication for Trojan and Titan AFV
3 7 11 1
Totals 100 128 13
Age Restriction This qualification is available to learners aged 18 years and over. Opportunities for Progression This qualification creates a number of opportunities for progression through career
development and promotion.
Exemption No exemptions have been identified.
3
Credit Transfer Credits from identical RQF units that have already been achieved by the learner may be
transferred.
Glossary
For the purposes of this qualification the definitions below apply.
AB xxx Army Book xxxx
AFV Armoured Fighting Vehicle
APU Auxiliary Power Unit
AVRE Armoured Vehicle Royal Engineer
BEMA Bulldozer Earth Moving Attachment
CoSTE Control Special to role Equipment
CSB Combat Support Bridge / Close Support Bridge
EFR Equipment Failure Report
ETI Elapsed Time Indicator
FWMP Full Width Mine Plough
GEMs Suggestion Scheme
HSD Hard Surface Device
IER Inspectorate of Engineer Resources
JAMES Joint Asset Management & Engineering Solution
MAPM Maintenance and Procedural Memorandums
MFS Monthly Functional Service
MSTE Marshall to Role Equipment
OHM Oil Health Monitoring
OMS Obstacle Marking System
SCR Service Counter Revolutions
TWMP Track Width Mine Plough
4
Qualification Units
URN: L/617/0309
Title: Supervise Titan Operation and associated Equipment
Level: 3
Credit value: 3
GLH: 25
TQT: 28
Learning outcomes The learner will:
Assessment criteria The learner can:
1 Supervise No 10 CSB operations
1.1 Supervise launch & recovery of No 10 (26) CSB
1.2 Supervise reconfigure a No 10 (26) to a No 10 (22) CSB
1.3 Supervise launch & recovery of a No 10 (22) CSB
1.4 Supervise reconfigure a No 10 (22) to a No 10 (26) CSB
1.5 Supervise fitting Trestle Set to a No 10 CSB
1.6 Supervise removing Trestle from a No 10 CSB
1.7 Supervise launch & recovery of No 10 (26) CSB – Folded
1.8 Supervise stripping No 10 CSB in preparation for IER
Inspection/ maintenance
1.9 Supervise inverting a CSB panel
1.10 Prepare a No 10 CSB for IER Inspection
1.11 Supervise building a No 10 CSB
2 Supervise No 12 CSB operations
2.1 Supervise launch & recovery of a No 12 CSB
2.2 Supervise launch & recovery of 2 x No 12 CSB
2.3 Supervising stripping a No 12 CSB in preparation for IER
Inspection/ maintenance
2.4 Prepare a No 12 CSB for IER Inspection
2.5 Supervise building a No 12 CSB
3 Supervise No 11 CSB operations
3.1 Supervise building a No 11 CSB
3.2 Supervise launch & recovery of a No 11 CSB
3.3 Supervise stripping a No 11 CSB (Reconfigure to No 10 (26)
CSB)
4 Supervise connecting, disconnecting & operation of AVRE Trailer
4.1 Supervise connect & disconnect AVRE Trailer
4.2 Supervise operation of AVRE Trailer
5 Supervise the fitting, removing &
5.1 Supervise the fitting of TWMP onto TITAN
5.2 Supervise fitting & removing HSDs
5
operation of TWMP 5.3 Supervise operation of TWMP
5.4 Supervise removing of TWMP from TITAN
5.5 Supervise TWMP Maintenance
6 Supervise the fitting, removal & operation of BEMA (I)
6.1 Supervise fitting BEMA(I) onto TITAN
6.2 Supervise operation of BEMA(I)
6.3 Supervise removing BEMA(I) from TITAN
6.4 Supervise BEMA Maintenance
7 Supervise the movement of towed equipment whilst marshalling from the ground & in a controller role
7.1 Marshal TITAN with AVRE Trailer connected - From the
ground forward - MSTE 1
7.2 Marshal TITAN with AVRE Trailer connected - From the
ground in reverse - MSTE 2
7.3 Marshal TITAN with AVRE Trailer connected - Through a
cone exercise - MSTE 3
8 Control TITAN as a single vehicle (Non Tactical)
8.1 Control TITAN as a single vehicle (Non tactical) On public
roads - CoSTE 2
8.2 Control TITAN as a single vehicle (Non tactical) - Along
defined tracks - CoSTE 3
8.3 Control TITAN as a single vehicle (Non tactical) - Negotiate
AFV transport - CoSTE 4
8.4 Control TITAN as a single vehicle (Non tactical) - Negotiate
current obstacle crossing equipment - CoSTE 5
9 Adhere to the Health and Safety requirements relevant to TITAN operations
9.1 Explain the relevant requirements of Health and Safety
9.2 Adhere to the relevant requirements of Health and Safety
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TITAN
Armoured Fighting Vehicle and crews during the
launch and recovery of Combat Support Bridging
(CSB) operations, modifying the configuration of
CSBs. Candidates will also be able to supervise the
fitting and removal of ancillary equipment to TITAN
AFVs and control the AFVs movement.
Details of the relationship between the unit and relevant National Occupational Standards or other professional standards or curricula (if appropriate)
Specialist for role equipment, however there is some
synergy in LO4,5 &6 with:
COSVR397 Arrange and secure plant or machinery equipment for transportation
MPQPL399 Operate plant attachments
This unit maps to the 918 ME (ARMD) Class 1 course
Name of the organisation submitting the unit
Defence Awarding Organisation
6
URN: L/617/0312
Title: Supervise Titan Crew
Level: 3
Credit value: 2
GLH: 16
TQT: 19
Learning outcomes The learner will:
Assessment criteria
The learner can:
1 Supervise TITAN Crew
1.1 Comply with Standing Orders for the Operation of Armoured
Vehicles
1.2 Comply with Health & Safety Regulations
2 Supervise TITAN & associated equipment maintenance
2.1 Supervise Before, During & After Use maintenance
2.2 Supervise Periodic maintenance & Oil Health Monitoring
(OHM)
2.3 Supervise No 10 CSB maintenance
2.4 Supervise No 12 CSB maintenance
2.5 Supervise Trestle Set maintenance
3 Supervise the preparation of TITAN & associated equipment for inspection
3.1 Upkeep AB 413
3.2 Provide data for Joint Asset Management & Engineering
Solution (JAMES)
3.3 Maintain AB 6530
3.4 Complete GEMS, Equipment Failure Report (EFR) &
Maintenance and Procedural Memorandum (MAPM) Forms
4 Supervise the resupply & replenishment of TITAN & associated equipment
4.1 Supervise refuelling tasks
5 Adhere to the Health and Safety requirements relevant to TITAN operations and supervision
5.1 Explain the relevant requirements of Health and Safety
5.2 Adhere to the relevant requirements of Health and Safety
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TITAN
Armoured Fighting Vehicle and crews when preparing
to carry out maintenance activities.
Details of the relationship between the unit and relevant National
This unit has some synergy with the following NOS:
7
Occupational Standards or other professional standards or curricula (if appropriate)
SEMPEO2-72 Preparing and Manoeuvring Armoured
Fighting Vehicles (AFVs) for Maintenance and
Transportation
COSVR212 Implement and maintain health, safety,
environmental and welfare Practices
Name of the organisation submitting the unit
Defence Awarding Organisation
8
URN: R/617/0313
Title: Supervise Trojan Operation and associated Equipment
Level: 3
Credit value: 3
GLH: 26
TQT: 29
Learning outcomes The learner will:
Assessment criteria
The learner can:
1 Carry out the duties of a Crane Supervisor
1.1 Direct & supervise lifting operations
1.2 Assess lifting operation dangers iaw site conditions
1.3 Review lifting operations iaw the method statement
2 Carry out the duties of a Slinger
2.1 Select suitable lifting accessories & lifting equipment
2.2 Visually inspect & prepare lifting tackle for use
2.3 Establish weights, balance loads & distances, heights &
clearances
2.4 Attach & detach loads
2.5 Direct safe movement of the crane & load during lifting
operations
3 Supervise Excavator operations (When using the Excavator for loading, unloading & during maintenance)
3.1 Supervise Excavator movement
3.2 Supervise movement of the Excavator into the Rail Move
position
3.3 Supervise Excavator operation when building or stripping
FWMP
4 Supervise the loading & unloading of Midi Pipe Fascine to & from TROJAN
4.1 Supervise loading Midi Pipe Fascine using the Excavator
4.2 Supervise unloading Midi Pipe Fascine using the Excavator
4.3 Supervise launching Midi Pipe Fascine
4.4 Supervise recovering Midi Pipe Fascine
4.5 Supervise Fascine Maintenance
5 Supervise connecting, disconnecting & operation of AVRE Trailer
5.1 Supervise connect & disconnect AVRE Trailer
5.2 Supervise operation of AVRE Trailer
5.3 Connect & disconnect AVRE Trailer using Blow Out Pin to
TROJAN
6 Supervise the fitting, operation & removal of FWMP
6.1 Supervise Building FWMP
6.2 Supervise fitting FWMP to TROJAN
6.3 Supervise fitting & removing HSCDs
6.4 Supervise the operation of FWMP
6.5 Supervise removing FWMP from TROJAN
6.6 Supervise FWMP Maintenance
9
7 Supervise the fitting, operation & removal of BEMA(I)
7.1 Supervise fitting BEMA(I) to TROJAN
7.2 Supervise operation of BEMA(I)
7.3 Supervise removing BEMA(I) from TROJAN
7.4 Supervise BEMA(I) Maintenance
8 Supervise the fitting, operation & removal of OMS
8.1 Supervise fitting OMS to TROJAN
8.2 Supervise operation of OMS
8.3 Supervise removing OMS from TROJAN
9 Supervise the movement of towed equipment whilst marshalling from the ground
9.1 Marshal TROJAN with AVRE Trailer connected - From the
ground forward - MSTE 1
9.2 Marshal TROJAN with AVRE Trailer connected - From the
ground in reverse - MSTE 2
9.3 Marshal TROJAN with AVRE Trailer connected - Through a
cone exercise - MSTE 3
9.4 Supervise connecting & disconnecting PYTHON Trailer
9.5 Marshal TROJAN with PYTHON Trailer connected - From
the ground forward - MSTE 1
9.6 Marshal TROJAN with PYTHON Trailer connected - From
the ground in reverse - MSTE 2
9.7 Marshal TROJAN with PYTHON Trailer connected - Through
a cone exercise - MSTE 3
10 Control TROJAN as a single vehicle (Non Tactical)
10.1 Control TROJAN as a single vehicle (Non-tactical) - On
public roads - CoSTE 2
10.2 Control TROJAN as a single vehicle (Non-tactical) -
Along defined tracks - CoSTE 3
10.3 Control TROJAN as a single vehicle (Non-tactical) -
Negotiate AFV transport - CoSTE 4
10.4 Control TROJAN as a single vehicle (Non-tactical) -
Negotiate current obstacle crossing equipment - CoSTE 5
11 Supervise the loading & unloading of Engineer stores & equipment into & from the AVRE Trailer
11.1 Supervise the loading & unloading of Midi Pipe
Fascine(s) into & from the AVRE Trailer
11.2 Supervise loading & unloading of TWMP into & from the
AVRE Trailer
11.3 Supervise loading & unloading of BEMA(I) into & from
the AVRE Trailer
11.4 Supervise the loading & unloading of Engineer stores
into & from the AVRE Trailer
12 Supervise the use of Power Tools
12.1 Supervise use of the Hydraulic Impact Wrench
12.2 Supervise use of the Hydraulic Chipping Hammer
12.3 Supervise removing/ replacing a worn or damaged Track
Pad
13 Adhere to the Health and Safety requirements relevant to TROJAN operations
13.1 Explain the relevant requirements of Health and Safety
13.2 Adhere to the relevant requirements of Health and Safety
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TROJAN
Armoured Fighting Vehicle and crews. Candidates will
10
also be able to supervise the fitting, removal and use
of ancillary equipment to TROJAN AFVs and control
the AFVs movement.
Details of the relationship between the unit and relevant National Occupational Standards or other professional standards or curricula (if appropriate)
This unit has some synergy with the following NOS:
COSVR531 Supervise lifting activities
COSVR397 Arrange and secure plant or machinery equipment for transportation
MPQPL399 Operate plant attachments
This unit maps to the 918 ME (ARMD) Class 1 course
Name of the organisation submitting the unit
Defence Awarding Organisation
11
URN: D/617/0315
Title: Supervise Trojan Crew
Level: 3
Credit value: 2
GLH: 16
TQT: 18
Learning outcomes The learner will:
Assessment criteria The learner can:
1 Supervise TROJAN Crew
1.1 Comply with Standing Orders for the Operation of Armoured
Vehicles
1.2 Comply with Health & Safety Regulations
2 Supervise TROJAN & associate equipment maintenance
2.1 Supervise Before, During & After Use maintenance
2.2 Supervise Periodic maintenance & Oil Health Monitoring
(OHM)
2.3 Supervise Excavator maintenance
2.4 Supervise TWMP maintenance
2.5 Supervise FWMP components maintenance
2.6 Supervise BEMA(I) maintenance
2.7 Supervise OMS maintenance
2.8 Supervise Fascine maintenance
2.9 Supervise AVRE Trailer maintenance
2.10 Supervise AVRE Trailer maintenance
2.11 Supervise remove & replace a track by explosive means
3 Supervise the preparation of TROJAN & associated equipment for inspection
3.1 Upkeep AB 413
3.2 Provide data for the Joint Asset Management & Engineering
Solution (JAMES) input
3.3 Maintain AB 6530
3.4 Complete GEMS, Equipment Failure Report (EFR) &
Maintenance and Procedural Memorandums (MAPM)
4 Supervise the Resupply & Replenishment of TROJAN & associated equipment
4.1 Supervise refuelling
5 Adhere to the Health and Safety requirements relevant to TROJAN operations and supervision
5.1 Explain the relevant requirements of Health and Safety
5.2 Adhere to the relevant requirements of Health and Safety
12
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TROJAN
Armoured Fighting Vehicle and crews when preparing
to carry out maintenance activities on the AFV and
associated equipment.
Details of the relationship between the unit and relevant National Occupational Standards or other professional standards or curricula (if appropriate)
This unit has some synergy with the following NOS:
SEMPEO2-72 Preparing and Manoeuvring Armoured
Fighting Vehicles (AFVs) for Maintenance and
Transportation
COSVR212 Implement and maintain health, safety,
environmental and welfare practices
Name of the organisation submitting the unit
Defence Awarding Organisation
13
URN: H/617/0316
Title: Supervise Trojan and Titan AFV maintenance tasks
Level: 3
Credit value: 2
GLH: 10
TQT: 19
Learning outcomes The learner will:
Assessment criteria The learner can:
1 Carry out mechanical tasks
1.1 Identify standard components & fittings
1.2 Use & Care for Specialist Tools
1.3 Identify Sealing Devices
1.4 Remove & Replace a stud or damaged bolt
1.5 Remove & Replace pipes, unions & joints
1.6 Understand Basic Hydraulics
1.7 Understand CV12 TCA 8A Mechanical Information
1.8 Understand CV12 TCA 8A - Lubrication System Mechanical
Information
1.9 Understand CV12 TCA 8A - Cooling System Mechanical
Information
1.10 Understand CV12 TCA 8A - Fuel System Mechanical
Information
1.11 Understand CV12 TCA 8A - Induction System
Mechanical Information
1.12 Understand TROJAN/ TITAN Running Mechanical
Information
1.13 Understand TN54 No 5 Mk 1 - Transmission Mechanical
Information
1.14 Prepare the Power pack for removal & reconnection
1.15 Prepare the APU for removal & reconnection
1.16 Supervise remove & replace a track
1.17 Remove & replace a track by explosive means
1.18 Renew a Guide Roller & Guide Roller Wheel
1.19 Supervise Removal & Replacement of Road wheels
1.20 Supervise Removal & Replacing Sprockets
1.21 Supervise Track Inspection
2 Adhere to the Health and Safety requirements relevant to TROJAN and TITAN
1.1 Explain the relevant requirements of Health and Safety
1.2 Adhere to the relevant requirements of Health and Safety
14
maintenance tasks
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TROJAN
and TITAN Armoured Fighting Vehicle crews carrying
out maintenance activities. Many of the activities in
this unit will be integrated with naturally occurring work
when preparing to use, or after AFVs have been
operated.
Details of the relationship between the unit and relevant National Occupational Standards or other professional standards or curricula (if appropriate)
This unit has some synergy with the following NOS:
LANLEO16 Service and repair wheels and tracks on
land-based equipment
COSVR661 Remove and replace plant or machinery
components to restore operational use
Name of the organisation submitting the unit
Defence Awarding Organisation
15
URN: K/617/0317
Title: Carry out emergency procedures and communication for Trojan and Titan AFV
Level: 3
Credit value: 1
GLH: 7
TQT: 11
Learning outcomes The learner will:
Assessment criteria The learner can:
1 Supervise casualty evacuation - TROJAN
1.1 Evacuate the casualty from the driver's compartment
1.2 Evacuate the casualty from the operator's compartment
1.3 Evacuate the casualty from the commander's hatch
1.4 Evacuate the casualty through the Escape Hatch
2 Supervise casualty evacuation - TITAN
2.1 Evacuate the casualty from the driver's compartment
2.2 Evacuate the casualty from the commander's hatch
2.3 Evacuate the casualty from the TITAN with a bridge fitted
3 Supervise firefighting procedures using firefighting equipment
3.1 Supervise Power pack Compartment firefighting procedures
on TROJAN
3.2 Supervise Hydraulic Compartment firefighting procedures on
TROJAN
3.3 Supervise Crew Compartment firefighting procedures on
TROJAN
3.4 Supervise Power pack Compartment firefighting procedures
on TITAN
3.5 Supervise Hydraulic Compartment firefighting procedures on
TITAN
3.6 Supervise Crew Compartment firefighting procedures on
TITAN
4 Supervise troop level recovery
4.1 Conduct reconnaissance of a recovery task
4.2 Brief the crew
4.3 Prepare the vehicle & recovery equipment
4.4 Supervise the recovery of the casualty vehicle
4.5 Conduct post recovery actions
5 Supervise Road Traffic Incident(s) (RTI)
5.1 Complete FMT 3 action
5.2 Supervise traffic control
6 Supervise Inter vehicle starting
6.1 Supervise inter vehicle starting operations
6.2 Supervise tow starting
7 Operate the vehicle communications equipment
7.1 Operate the vehicle Radio/ I/C System
8 When dismounted 8.1 Use hand signals
16
using hand or torch signals
8.2 Use torch signals
9 Adhere to the Health and Safety requirements relevant to TITAN and TROJAN operations
9.1 Explain the relevant requirements of Health and Safety
9.2 Adhere to the relevant requirements of Health and Safety
Additional information about the unit
Unit purpose and aim(s) This unit is about candidates supervising TROJAN
and TITAN Armoured Fighting Vehicle crews in the
procedures to be followed in the event of an
emergency involving the AFV or its crew.
Details of the relationship between the unit and relevant National Occupational Standards or other professional standards or curricula (if appropriate)
This unit has some synergy with the following NOS:
COGESA12.20 Evacuate casualties
SEMPEO2-72 Preparing and Manoeuvring Armoured
Fighting Vehicles (AFVs) for Maintenance and
Transportation
COSVR396 Direct and guide the movement of vehicles, plant or machinery
Name of the organisation submitting the unit
Defence Awarding Organisation