8/12/2019 Danbo Instruction

1/2

Look at the instruction page while following the steps here below:

First of all, you've to print the papercraft template out. You can either print it out on a card or on an

A paper and then glue the paper with the template on a cardboard. You can also directly print it out

on an A paper and make the !anbo, but then your !anbo would be very fragile.

Also " would recommend using superglue, "'ve no idea what kind of brand "'ve used. #andom kindof brand is good, as long as it keeps everything on its place $%

&tep : (ut out ) and glue along the lid and glue it together. *hat's the base of the arm.

&tep +: (ut out and fold along the lines. And glue the sides to the side on the base of the armyou've made in step . #epeat this for the other arm.

&tep : (ut out -) and fold the teeths and the white flap. /lue the white flap to the other end ofthe same paper. &o you will have a sort of ring 01%. 2ut glue on the teeths and glue -3 on it. !o the

same for the other side of the same ring 01%. You should have + little cylinders. *hen cut out 4 and

glue it together. 5ow put the cylinder you've made before in 4, it should fit nicely. 0!on't glue itthough6% #oll the longer part of 4 which you haven't glued yet, around the cylinder and glue it on

the end of it. 7ake sure you don't glue the cylinder. *he cylinder should be able to move if you rollit. *his is the 8oint for the arm.

&tep : Assemble the base of the arm and the 8oint of the arm together, by glueing the + sides of the

cylinder on .

&tep 9: (ut out the circle 0on -% and cut out -. ;n the circle - you see a cross, follow the cross

with a cutter, so you will get flaps. Fold the flaps upwards, so the white paper is visible. 2ut -under the hole you've cut out in - without using glue 08ust make sure the fold are visible%. 2ut glue

on the white flaps 0make sure the glue doesn't come on else where% and then glue on it. >

this image might help if you don't get what " mean. !o the same thing with the two other holes onthe body. *his time wtih and 4. *hen glue the body together.

&tep ): /lue the arms on the sides of the body. *he arms should be able to turn and go upwards and

downwards now.

&tep 3: 7ake + cylinders again, but this time with ? 9. Also cut out . !o the same as in step

. @ut this time, you've to place + cylinders.

&tep : (ut out + and fold both. /lue each on the sides of the cylinders from step 3.

&tep 4: /lue what you've made in step on the top of the body. *his is 8oint for the head.

&tep -: (ut - ? - out. (ut out the eyes in - and glue - behind it. 0(an skip this if you want to,

it 8ust gives depth to the eyes, " would not recommend this if you're making it on paper.% *hen glue

the head together.

&tep : /lue the head on the top of the 8oint of the head. 0hat you've made in step 4% You're headshould be able to turn and go upwards and downwards now.

&tep +: (ut out -+ and glue it together, but leave the long part as shown on the picture.

&tep : (ut out 3 ? 9 and make the cylinder. 2ut the cylinder on what you've made in step + and

8/12/2019 Danbo Instruction

2/2

glue the long part. 7ake sure the cylinder can roll if you turn it. 5ow you've the feet.

&tep : At last glue the two sides of the cylinder of feet and attach it in the body.

5ow you have a !anbo >