D75KS blasthole drill

The D75KS is a diesel powered, self-propelled crawler mounted drill designed for high-pressure down-hole or low-pressure rotary blasthole drilling in the mining and construction industry.

This drill can be operated by one man and is equipped to rotary drill 229 to 279 mm (9 to 11) diameter holes. Optional high pressure compressors add flexibility to drill with 8 DTH

hammers. Pulldown is up to 334 kN (75 000 lb) and bit load 409 kN (92 000 lb) for good penetration rate even in hard rock formations. Pipe length is 10,7 m (35) and the rig carries up to four pipes as standard in a safe and efficient internal loader. The D75KS is ideal for multipass drilling of benches up to 53 m (173) high, such as for stripping of overburden material.

Type Excavator type, Model 330EL Pad width 850 mm (33 1/2) Pad type Triple grouser Rollers Sealed,oilfilled,excavatortype Number of lower rollers 11 Upper track chain support Two upper carrier rollers Rock guards Full length Overall length 5,31 m (17 5) Width over tracks 4,27 m (14 0) Drive type Independent hydrostatic motors Final drive Heavydutyspurgears,oilflooded Drive HP each track 119 kW maximum (160 hp) Brakes Spring set, hydraulic released Brake release for towing Manual Tram speed 2,4 km/h (1 1/2 mph) Gradeability, mast down 59% (approx. 28 degrees) Rear axle 203 mm (8) diameter solid round Front axle Three point oscillating type Track adjustment means Hydraulic with grease gun Unit bearing pressure 75,1 kPa (10.9 psi) with standard equipment

D75KS undercarriage

D75KS frame & integral jacks

Type Wideflangebeammainrailswithheavycross bracingandreinforcedathighstressareas Main rail size/material W 18 x 119#, ASTM A572 alloy grade 50 Main rail section modulus 166 Construction Electricspraytransferweldingmethodby AWScertifiedwelders Jack, mast, deck supports Welded integrally Battery box Rightsideofengine,removabletopcover Right deck Non skid, 686 mm (27) wide Walkways Opengripstrut,610mm(24)wide,fromcab torightdeckandfronttoservicecooler andaircleaners.Leftsidetoservice compressor receiver tank and dust control systems. Complete with handrails , kick plates and access ladders. Handrails 41 x 1067 mm high (1 5/8 dia x 42) with centerrailand102mm(4)kickboards. Towhooks Welded,2front,2rear Leveling Jacks Number 3 Location 2atrear,1atfrontoncenter Cylinder bore 178 mm (7) Cylinder rods 102 mm (4) diameter, chrome plated Cylinder stroke 1219 mm (48) Lift capacity each 427kN(96000lbs) Pad connection Ball and pinned socket Pad diameter 762 mm (30) Safety check valves Integral in each cylinder Extension boot 273 mm (10 3/4) OD x 15,2 mm (5/8) wall Pad ground clearance 559mm(22)front,457mm(18)rearwhen retracted Indicator lights Jack up indicator lights on operators console

Model C27 Rated horsepower 597 kW (800 hp) Full load RPM 1800 Starting system Dual 24 volt DC, high torque 50MT starters Alternator 24 volt DC, 100 amp heavy duty Safety shutdown system 24 volt DC, energize to run Intake air cleaner Type Drytypewithsafetyelement Model SRG20 Rating 2000cfmat71/5inchesofwater Batteries Four size 8D, 12 volt, 1350 CCA Muffler Two Industrial type, 6 inlet and outlet Muffler guard 12gal.steelforpersonnelprotection Jacket water cooling Radiator/fan Standard ambient rating range -VE 15C(5F) +VE 54C (-130 F) Cold weather equipment Ether injection system Fuel tank 2274L(600gal)mountedbetweenframebeams Turbo and manifold covers Thermalwrapcoversforpersonnelprotection Mounting to main frame Threepointshockmountingthroughrubberisolators Compressor Type Oilfloodedscrew,singlestage Inlet flow 45m/min(1600scfm) Max operating pressure 6,9 Bar (100 psi) Intake air cleaner Type Drytypewithsafetyelement Rating 2000cfmat7-1/5inchesofwater Oil separation Verticalbarrierelement,pre-separation in 265 L (70 gal) horizontal sump Oil filtration 25m(25micron)replaceableelement Drive Directtoengineflywheelthroughsoftcoupling Controls Automaticwithsafetyshutdownsystem Air shut off Hydraulic, control at operators panel Connection to rotary head 63,5 mm (2 -1/2) shock mounted pipe and air hose

D75KS power group

D75KS mast

Construction Rectangulartubing,welded/stressrelieved, spraytransferweldingmethodw/beveled toejointsandrecessedsidemembers, andreinforcinginhighstressareas Steel grade, main members ASTM A500, grade B, 400 Mpa (58 000 psi) min. Tensile Main chord size 152 x 76 x ,63 mm (6 x 3 x 1/64) Width over chords 1473 mm (58) Depth over chords 927 mm (36 - 1/2) Standard length 13,7m(45ft) Pivot and raising area 19,05mm(3/4)backplatewithfulllengthcylinder topivotlugstodistributestress Pivot bushings Replaceablealloyaluminumbronze Hydraulic lines Pressureratedsteelhydraulictubing,feed, rotation, air in plastic clamps Hose rack Sheetsteeltroughformovinghoses

D75KS feed system

Type Hydraulic cylinder and chain Number of cylinders 2 Cylinder bore 152 mm (6) Cylinder rods 114 mm (4 -1/2) diameter, chrome plated Cylinder stroke 6,1 m (240) Chain type 2 heavy series roller chains with heavy side barsandthruhardenedpins Chain size, feed ANSI #200, 63,5 mm (2 -1/2) pitch Chain rating, feed Ultimatestrength-600kN(135000lbs)each Chain size, retract ANSI #160, 50,8 mm (2) pitch Chain rating, retract Ultimatestrength-311kN(70000lbs)each Top timing shaft Bronzebushedtubeonalloyshaft Chain sprockets, feed Timkentapperedrollerbearings Chain sprockets, hoist Bronzedbushed,greasefittinginshaft Standard rotary head stroke 12,19 m (40) Rated down pressure 334kN(75000lbs) Feed rate 27m/min(0to89fpm) Rated pullback 193kN(43400lbs)at100%efficiency Retract rate 34,8m/min(0to114fpm) Adjustable head guide shoes Steelwithreplaceablenylatronwearblocks Chain adjustment Hydraulic jack with pins Feed cylinder chain guards Slidingsteelchannelbetweenchainand cylinder to protect rods Sprocket/chain guards 9,5mm(3/8)plateattablearea,removeable

D75KS operators cab

Location Torightandrearofmast Type Two man, shock mounted Length 1,82 m (72) Width 1,75 m (69) Floor area 3,2 m(34-1/2ft) Height inside 1,98 m (6 6) Construction Welded 10 gal steel with 63,5 mm (2 -1/2) tubularframe,4,5mm(3/16)sheetsteelroof Roof window 305x355mm(12x14)safetyglasswithguard Windows 6,35mm(1/4)Tintedsafetyglassandmolding Number of windows 8 Doors Two, swing type with heavy duty hinges and rotarytype,lockabledoorlatch Operators seat Upholstered,adjustablew/armrests, spring suspension Helper seat Flip-up upholstered seat at rear Sound level rating 80 dB(A) or less Cab heater, air conditioner and pressurizer Type 24voltDCrooftopunit Location Cabroof Heating capacity 15825 kJ (15 000 Btu) Air flow 13,3 m/min(470cfm) Cooling capacity 17935 kJ (17 000 Btu) AC compressor drive BeltdrivenfromenginePTO FOPS cover Meets FOPS drop criteria per SAE J231 Operator controls location Consoleatfrontwallofcab Back access to controls Twolockableaccessdoors,hingedtop Electrical 24 VDC system, negative ground through mainframe,NEMA4enclosures

Gearcase All steel welded/stress relieved Main thrust bearings Timken steep angle roller Seals Doubleliptype,upperandlower Bullshaft Tubularheattreatedalloysteel Bullshaft thread 5 1/2 API REGULAR Air passage thru head 63,5 mm (2 1/2) diameter Lubrication Oilflooded Air swivel packing Integralwithupperbullshaft Gearing Spurplanetaryandfinaldrive Drive motor Hydraulic Maximum rotary horsepower 145 kW (195 hp) Standard rotary speed/torque 0-94rpm@14236Nm(126000in-lb) Optional rotary speed/torque 0-114rpm@11782Nm(104276in-lb) Optional rotary speed/torque 0-144rpm@9625Nm(82000in-lb) Optional 2 Speed speed/torque 94/144 rpm @ 14 236/9 625 Nm (126000/82000in-lb) RPM gauge Proximitypickuptocountteethonbullgear

D75KS rotary head

D75KS hydraulic system

Hydraulic oil cooling system Oil cooler with 60 C (140 F ) stats and check valve Oil reservoir 872 L (230 gal) with sight glass and temp gauge Reservoir pressurization 0,345bar(5psi)air,filteredbreather Pump inlet supercharge 9bar(125psi)forfeedandhydrostatics Reservoir refill system Handpumpthru5m(5micron)intankfilters System refill capacity 1213 L (320 gal)

Base locking type Pinlocks,drilltabletomainframe Position locking means Two hydraulic powered lock pins Pin size 102 mm (4) diameter, HT alloy steel Angle range 0 to 25 Angle increments 5 Pin lock indicators Lightindicatorincab,lock/unlock

Outside pipe support Type Heavy duty service, swing in type Location Leftoutsideofmast Height above table 2,1 m (7 0) Power Hydraulic cylinder swing and clamp

Work deck leveling Adjustableto25 Adjustment means Deckpivotsatrearoftable Position locks Adjustablelengthchainstotable

Feed cylinder chain guards Loader booster cylinder Controls Lock pins and pipe support controls at operators panel

D75KS angle drilling (option)

Paint Single paint color other than standard - Orange, Grey & WhiteTraining One week start up - USA/Canada One week start up - International Additionaldayofstartuptraining(12hr) Power Group QSK19C 567 kW, 45,3m/min/ 6,9 Bar (1600/100)@1800 RPM C27 596 kW, 56,6 m/min / 6,9 Bar (2000/100)@1800 RPM C27 652 kW, 56,6 m/min / 6,9 Bar (2000/100)@1800 RPM QSK23 708 kW, 56,6 m/min / 6,9 Bar (2000/100)@1800 RPM Airvolumecontrolforlowpressurecompressor C27 596 kW, 38,2 m/min / 24,1 Bar (1350/350)@2100 RPM C27 652 kW, 38,2 m/min / 24,1 Bar (1350/350)@2100 RPM QSK19C 567 kW, 38,2m/min/24,1 Bar(1350/350)@2100 RPM AirvolumecontrolforhighpressurecompressorDust Control Water injection 34 L/min (9 gpm) with 2,271 L (600 gallon) tank Sandvikdrydustcollector,136m/min(4800scfm),nowater Tiptondrydustcollector,200m/min(7000scfm)Rotary Head Rotaryhead,0-114RPM,torque11782Nm(104276in-lb) Rotaryheadspeed,0-144RPM,torque9265Nm(82000in-lb) Rotary head, dual speed 0-94 RPM and 0-144 RPM Angle Drilling Angle drilling 0-25 in 5 increments (std mast only) Mast Equipment PipethreadgreaseroperatedfrominsidecabLubrication Airlinelubricator114L(30gallon)reservoir Centrallubesystem,manualviacentralpoint Centrallubesystem,automatic,19L(5gallon) Centrallubereservoir,upgraded208L(55gallon) Pre-startlubricationpump Lubricationsystemforpulldownchain Remoteoildrainsystem(engineandgearboxes) Fluidsservicecenter,fill,andhydraulicevacuation SOSsamplesystemforengine,compressorandhydraulicsElectrical Battery disconnect system (included in CE group) Premium lighting upgrade, 12 lights and 175 Ampere alternator 24 Volt to 12 Volt converter Compressed Air Cleaning kit, air gun with 7,6 m (25) hose Cleaning kit, air gun with 15,2 m (50) hose with reel Operators Cab Electronicdepthcounter(EDC),modifiedtoMetric Electriccontrolsfortramming,mast,andleveling Auto leveling (requires electric controls) Remote tramming (requires electric controls) Cabsunshades Windowwiper,front,rear,windows,andwashers

D75KS options

D75KS options

Protective devices Tram stop pedal, head/loader, tram/jack, tram/head interlocks Groundlevelemergencyshut-off Emergencystopcableinmast(includedinCEgroup) Warningaccessories,airhorn,roofandmaststrobelights Ansulfiresuppresion,manuallyactuated FireextinguisherchemicalABC9kg(20lb)(inCEgroup)Export Export preparation and packaging Name plates in Spanish Name plates in Russian CE group with receiver tank, manuals in English Cold Weather -40C(-40F)electricheat(L&M,battery,engine,PTO,fluids) 25 kW generator (recommended with package) L&M cooler upgrade, max 46C (115F) (included in package) Hydraulic pump PTO disconnect (included in package) Remote start (in package) Water electric heater, insulated pump cover (not in package) Dieselpre-heaterforengine,fuellinewarmer(inpackage) Heatingforairlinelubricator(notinpackage) Exhaustheaterforwatertank(notinpackage) Additionalcabheaterfromenginecoolant(notinpackage)Miscellaneous Hydraulic system test station Wash group, 15 m (50) hose, reel (requires water injection)Manuals Additional Parts Manual PAPER Additional Parts Manual CD ROM Additional Service Manual PAPER Additional Parts Manual LAMINATED PAPER Additional Service Manual CD ROM AdditionalOperator/Maint/LubeGuidesPAPER AdditionalOperator/Maint/LubeGuidesCDROM Additional Engine Parts Manual PAPER Training module set on PAPER Training module set on CD ROM All Service & Operators Manuals in Spanish or Russian Drill String Basic 5.5 DTH string, incl 1 ea 9,1 & 10,6 m pipes, 3.5 Beco Basic 7-5/8 DTH string, 1 ea 9,1 & 10,6 m pipes, 6 Beco Basic 7 rotary string, incl 2 ea 10,6 m pipes, 4.5 Beco Basic 7-5/8 rotary string, incl 2 ea 10,6 m pipes, 6 Beco Basic 8-5/8 rotary string, incl 2 ea 10,6 m pipes, 6 BecoWarranty Gold C27 warranty, USD200 deduct 5 yr 10k hrs (US/Can only) Extended drill warranty, 18 months/5000 hours, excl engine

D75KS dimensions & weights

Dimensions Length, mast down 15,54 m (51 0) Length, mast up 10,97 m (36 0) Width, operating 5,05 m (16 7) Width over track shoes 4,27 m (14 0) Height, mast down 5,33 m (17 6) Height, mast up 16,33 m (53 7) Ship dims, mast only 2,3 m W x 15,4 m L x 1,9 m H (7 6 x 50 6 x 6 2) Ship dims, base only 4,3 m W x 11 m L x 4,1 m H (14 x 36 x 13 6)

Weights

Bare weight (less tools) 56246kg(124000lbs) Operating weight 64864kg(143000lbs) Bare weight, std base only 40370kg(89000lbs) Bare weight, mast assy only 15876kg(35000lbs)

SANDVIK MINING AND CONSTRUCTION WWW.SANDVIK.COM

SAN

DVI

K is

a re

gist

ered

trad

emar

k of

the

Sand

vik

Gro

up

201

1 Sa

ndvi

k

Sandvik is a high-technology engineering group with world-leading positions in selected areas tools for metal working, advanced materials technology, and mining and construction. We are represented in 130 countries.

Sandvik Mining and Construction represents one third of the overall Sandvik Group and serves a broad range of customers in construction, mineral exploration, mining and bulk materials handling. Our construc-tion expertise covers quarrying, tunneling, demolition and recycling, and other civil engineering applications. Our mining products and services support customers on the surface and under ground, in all mineral, coal and metal mining applications from exploration to ore transportation.