documentd

‡Configuration of Water Valve is a trademark of Kimray, Inc.www.kimray.com

SE

CT

ION

D

‡®

NOTE: We reserve the right to modify or change, without prior notice, any statement or information contained herein. If exact dimen-sions or specifications are required by the customercertified prints will be furnished for a minimum charge upon request to KIMRAY, Inc.® Copyright 1992, KIMRAY, Inc.

www.kimray.comD:i

Issued 10/09

OIL AND WATER VALVES

TREATER VALVEDUCTILE IRON

Current Revision:

APPLICATION: As oil or water valve for emulsion treaters, water knockouts and gunbarrels. Can be used for pressure, atmospheric, or vacuum operation. Ideal for discharging salt water to disposal systems. Operating Description PartsMaterial Pressure of Operation List

Cast Iron 2"-125 psig Max. Pg. 10.1 Pg. 10.3Cast Iron 3",4",6"-60 psig Max. Pg. 10.1 Pg. 10.3Ductile 125 psig Max. Pg. 10.1 Pg. 10.4Steel 125 psig Max. Pg. 10.1 Pg. 10.5

TREATER VALVE

APPLICATION: Diaphragm motor for Mechanical Dump Valve Operating Parts Material Pressure List

Cast Iron 125 psig Max. Pg. 20.1

DIAPHRAGM MOTOR VALVE

2" & 3" Pg. 10.6REMOVABLE HARD SEAT ASSEMBLY

Treater Valves 10.2Diaphragm Motor Valve 20.2

DIMENSIONS & INSTALLATIONS

www.kimray.com


ELASTOMERS

D:iiIssued 9/12

Current Revision:Change material names

TEMPERATURE: -10° to +350° F -23° to +177° C

APPLICATION: Crude Oil & Gas Production, Glycol Dehydratbrs, Gasoline, Jet Fuel & Diesel Fuel Pumping, Water Disposal, Methanol Injection Pumps. (Also Vacuum Service) (Gas permeability is very low)

FLUID / GAS: Crude Oil & Gas, Sour Gas (C02), Propane, Gasoline, Diesel, Fuel Oil Systems

DO NOT USE WITH: Hot Water, Not preferred for wet H2S, Methyl Alcohol, Amines, Sodium hydroxide solutions


APPLICATION: Steam Flood

FLUID / GAS: Steam, Water, Alcohol

DO NOT USE WITH: Crude Oil & Gas, Diester Lubricants (Lube Oils)


APPLICATION: High abrasion resistance Seats, Diaphragms

FLUID / GAS: Crude Oil gas and Water, Sour Gas (C02), propane, butane, fuel, mineral oil and grease

TEMPERATURE: ±0° to +300° F -17° to +149° C

APPLICATION: Production Heaters, Thermostats

FLUID / GAS: Crude Oil & Gas at High Temperature

DO NOT USE WITH: Alcohol, Glycols

TEMPERATURE: +30° to +500° F 0° to +260° C

APPLICATION: Crude Oil & Gas Production (High heat), Steam Flood Production Chemicals (corrosion inhibitors) Amine Sweetener Systems, Gasoline, Diesel, Fuel Oil Systems

FLUID / GAS: Crude Oil & Gas Production, H2S, Steam, Petroleum fluids, Sea Water


APPLICATION: Crude Oil & Gas Production w/ H2S C02

FLUID / GAS: Crude Oil & Gas H2S, C02, Sea Water

TEMPERATURE: Buna-N: -40° to +220° F -40° to +105° C Low-Temp: -85° to +120° F -65° to +49° C

APPLICATION: Crude Oil & Gas Production Glycol Dehydrators, Gasoline, Jet Fuel & Diesel Fuel Pumping, Water Disposal, Methanol Injection Pumps, Water pump seals, hydraulic pump seals

FLUID / GAS: Crude Oil & Gas, Good to Poor in Sour Production (See HSN), Water, Glycols, Hydraulic Oils, Resistance to crude oil in the presence of hydrogen sulfide and amines, Diesel fuel, fuel oils

DO NOT USE WITH: Aromatic hydrocarbons, chlorinated hydrocarbons, phosphate esters (hydraulic fluids)


APPLICATION: Chemically Inert Elastomer Best in static Do not use at low temps

FLUID / GAS: Almost All Chemicals

AFLAS ® is a trade mark of Asahi Glass Co VITON ® is a trade mark of Dupont

EP (EPDM)

POLYURETHANE (P)

TEFLON (T)

POLYACRYLATE (H)

HSN (HNBR)

NITRILE

Current Revision:www.kimray.com

‡Configuration of Water Valve is a trademark of Kimray, Inc. D:10.1Issued 3/06


TREATER VALVE

APPLICATIONS: As oil or water valve for emulsion treaters, water knockouts and gunbarrels. Can be used for pressure, atmospheric, or vacuum operation. Ideal for discharging salt water to disposal systems.

FEATURES: Single soft seat for tight shut off Balanced against upstream pressure Balanced against downstream pressure or vacuum Standard weight and lever holds approx. 4’ liquid head Weights may be added to increase liquid head Can be manually opened and closed Sample tap on inlet connection Rotary stuffing box with leakless, low friction TEFLON pack-ing All interior parts can be removed without taking valve out of line Prevents air from entering salt water disposal system piping

®‡

OPERATION: The inlet of the valve is connected to the water siphon leg or oil discharge line from an emulsion treater or water knock-out. Vessel Gas Pressure (Red) is connected to the UPPER HOUSING to balance the Gas Pressure under the MAIN DIAPHRAGM. The effective area of the BALANCING DIAPHRAGM is the same as the effective area of the SEAT. Pressure or vacuum acting on either side of the BALANCING DIAPHRAGM will can-cel the pressure or vacuum acting on the SEAT. This balancing feature prevents the slamming open and closed prevalent in unbalanced single seat construction. The Vessel Gas Pressure (Red) with the UPPER HOUSING acts upwardly on the BALANCING DIAPHRAGM to cancel the downward pressure on the single SEAT. Downstream Pressure Vacuum (Blue) acting on the SEAT is communicated to the top side of BALANCING DIAPHRAGM. This cancels any down-stream pressure or vacuum effect on the valve operation. The force to hold the SEAT closed is applied by a WEIGHT and LEVER through a rotary TEFLON packed stuffing box to a PIVOT STEM which pushes down on the Diaphragm Assembly. When the liquid rises in the discharge piping of the vessel above the set level, it lifts the Diaphragm Assembly against the WEIGHT load to open the valve. As liquid is discharged to lower the level, the WEIGHT closes the valve. Liquid level may be adjusted up to approximately four feet by moving the WEIGHT on the LEVER. Additional weights may be added if a higher level is desired.


‡Configuration of Water Valve is a trademark of Kimray, Inc.D:10.2Issued 3/06


TREATER VALVEINSTALLATION AND DIMENSIONS

INSTALLATION DIMENSIONS

26 SWA 93/8 47/8 31/2 105/8 81/2 27 FWA-D 93/8 61/2 31/2 105/8 81/2 27 FWA-S 93/8 63/8 31/2 105/8 81/2 36 FWA 113/4 8 41/4 131/2 13 37 FWA-D 113/4 8 41/4 131/2 13 46 FWA 13 9 43/4 145/8 13 47 FWA-D 13 9 43/4 145/8 13 47 FWA-S 13 9 43/4 145/8 13 66 FWA 185/8 121/4 63/4 211/2 121/2

DIMENSIONS - INCHES Valve No. A B C D E

NOTE: Do not connect gas equalizing line to gas vent line, burner manifold, or downstream of mist extractor.

1 1,250 3,200 5,950 12,750 2 1,800 4,500 8,450 18,000 3 2,200 5,500 10,300 22,000 4 2,500 6,400 11,900 25,500 5 2,800 7,350 13,300 27,500 10 4,000 10,100 18,900 40,500 15 4,900 12,400 23,100 49,500 20 5,700 14,300 26,800 57,000 30 6,950 17,600 32,800 81,000 50 8,900 22,600 42,200 90,500 60 9,850 24,800 46,200 99,000 75 11,900 56,000

For gravity correction multiply values obtained from chart by . Where “G” is specific gravity of flowing liquid.G

1

CAPACITY - Bbls. Water/ Day, Steady Flow

2 3 4 6

Valve Size - InchesPress.Drop

AcrossValve


D:10.3Issued 11/11


TREATER VALVECAST IRON

ANGLE VALVES AVAILABLE: NOTES:

CAT. SIZE MAX NO. TYPE VALVE W.P. KITDAA 2" SCRD. 26 SWA 125 RELDAC 3" FLGD.** 36 FWA 60 REMDAD 4" FLGD.** 46 FWA 60 RENDAE 6" FLGD.** 66 FWA 60 REP

**Companion flanges, nuts, bolts and gaskets are furnished, at extra cost only when specified.

*These are recommended spare parts and are stocked as repair kits.

Lever Bars for higher liquid head are available 419L and 420L.

®‡

Current Revision:Change 2” Pin number


D:10.4Issued 7/11


TREATER VALVEDUCTILE IRON


CAT. SIZE MAX NO. TYPE VALVE W.P. KITDAB 2" FLGD.** 27 FWA-D 125 RELDAG 3" FLGD.** 37 FWA-D 125 REMDAH 4" FLGD.** 47 FWA-D 125 REN

**Companion flanges, nuts, bolts and gaskets are furnished, at extra cost, only when specified.

*These parts are recommended spare parts and are stocked as repair kits.

Lever Bars for higher liquid head are available 419L and 420L.

®‡



D:10.5Issued 7/11


TREATER VALVESTEEL


CAT. SIZE MAX NO. TYPE VALVE W.P. KITDAI 2" FLGD.** 27 FWA-S 125 RELDAJ 3" FLGD.** 37 FWA-S 125 REMDAF 4” FLGD.** 47 FWA-S 125 REN

**Companion flanges, nuts, bolts and gaskets are furnished, at extra cost, only when specified.


®‡



D:10.6Issued 3/06


REMOVABLE HARD SET ASSEMBLY

SEATS AVAILABLE:

Retainer

Hardened Removable Seat

Gasket

2" 384HA 384HB 387

3" 385PH 385HB 388 3" 385ASS6 385HB 388

SEAT RETAINER GASKETLINESIZE

www.kimray.comCurrent Revision:Change 2” Packing Ring quantity

D:20.1Issued 3/10


DIAPHRAGM MOTOR VALVECAST IRON

VALVES AVAILABLE: NOTES:

CAT. SIZE MAX NO. TYPE VALVE W.P. KITDMA 2" SCRD. 26 DM 125 REW



‡Configuration of Mechanical Oil Valve ia a trademark of Kimray, Inc.D:20.2Issued 2/09


DIAPHRAGM MOTOR VALVEINSTALLATIONS

USED AS DIAPHRAGM MOTOR FOR MECHANICAL DUMP VALVE. LIQUID HEAD AGAINST 26 DM DIAPHRAGM, ASSISTED BY 7 psig WEIGHT, MOVES LEVER WHICH OPENS DUMP VALVE. REFER TO SECTION “CP” FOR MECHANICAL DUMP VALVE OPERATION AND PARTS REFERENCE DRAWINGS.

NOTE: ADJUSTING BLOCKS SHOULD BE MOVED TO ADJUST FOR SPREAD. WEIGHT IS POSITIONED FOR MAXIMUM HEIGHT.

TYPICAL DIAPHRAGM MOTOR VALVE INSTALLATIONS

documentd

Documents

crude oil gas h2s

fuel oil systemsfluid

diaphragmsfluid gas

lowfluid gas

thermostatsfluid gas

sour gas c02

fuel oil systemsdo

mineral oil