cylinders - hallmark hose · 2019. 6. 6. · low pressure hydraulic option includes: rod seal buna...

6CY

LIND

ER

S

Cylinders

Pneumatic - P1D Cylinders ....................................................6-1 — 6-13

Pneumatic - P1D Mountings ................................................6-14 — 6-25

Pneumatic - P1D Accessories ..............................................6-26 — 6-27

Pneumatic - P1A Cylinders ..................................................6-28 — 6-33

Pneumatic - P1A Mountings ................................................6-34 — 6-37

Industrial - 2A Cylinders .......................................................6-39 — 6-47

Industrial - 3L Cylinders .......................................................6-39 — 6-47

Industrial - 2H Cylinders ................................ 6-39 — 6-43, 6-50 — 6-54

Industrial - Mountings ..........................................................6-55 — 6-57

Industrial - Seal Kits ............................................................6-58 — 6-59

If you can’t fi nd it, your local Parker distributor can!

Just because it’s not in our catalog doesn’t mean you can’t get it. To fi nd exactly what you need, contact your local

Parker distributor today. We can often provide 24-hour delivery direct from our factories to over 12,000 distribution locations

worldwide. Our business is keeping you on the move.

6-� Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1D Series

PneumatiC CylinDerS

P1D SerieS - General SPeCifiCationS

Quick reference

Bore Size

Cylinder Areacm2

Piston Rod

Cushioning Lengthmm

Air Consumption 1

litre Connection

Thread

Theoretical Cylinder Forces at 6 Bar (N) 2

Dia.mm

Areacm2

MaleThread Extend Stroke Retract Stroke

32 8.0 12 1.1 M10x1.25 17 0.105 G1/8 482 414

40 12.6 16 2.0 M12x1.25 19 0.162 G1/4 754 633

50 19.6 20 3.1 M16x1.5 20 0.253 G1/4 1178 989

63 31.2 20 3.1 M16x1.5 23 0.414 G3/8 1870 1681

80 50.3 25 4.9 M20x1.5 23 0.669 G3/8 3016 2721

100 78.5 25 4.9 M20x1.5 27 1.043 G1/2 4712 4417

125 122.7 32 8.0 M27x2 30 1.662 G1/2 7363 6880

160 201.1 40 12.6 M36x2 38 2.724 G3/4 12.064 11,310

200 314.2 40 12.6 M36x2 38 4.256 G3/4 18.850 18,096

Cylinder Bore Size

Total Mass (kg) Total Mass (kg) Moving Components

0mm Stroke Supplement per 10mm Stroke at 0mm Stroke Supplement per 10mm Stroke

Standard Tie-Rod Clean Standard Tie-Rod Clean All variants All variants

32 0.55 0.54 0.60 0.023 0.022 0.047 0.13 0.009

40 0.80 0.79 0.88 0.033 0.030 0.063 0.24 0.016

50 1.20 1.20 1.32 0.048 0.048 0.094 0.42 0.025

63 1.73 1.73 1.86 0.051 0.051 0.101 0.50 0.025

80 2.45 2.47 2.63 0.075 0.079 0.142 0.90 0.039

100 4.00 4.00 4.22 0.084 0.084 0.168 1.10 0.039

125 6.87 6.73 7.01 0.138 0.129 0.248 2.34 0.063

160 — 16.19 — — 0.160 — Consult Factory Consult Factory

200 — 22.23 — — 0.185 — Consult Factory Consult Factory1) Free air consumption per 10 mm stroke for a double stroke at 6 bar2) The values for cylinder forces are theoretical and should be reduced to suit working conditions.

P1D Clean VersionMin stroke 25mmProtection class Hose-proof in accordance with IP65 Chemical resistance Tested for normally used industrial detergents, both acid and alkaline

P1D rod lock Version• Fluid Medium: Dry, filtered, compressed air

• Maximum Cylinder Operating Pressure: �45 PSI

• Required Pressure to Unlock�: 58 PSI

• Minimum Torque Required for Manual Override Version: 32mm Bore = 8 in-lbs 40mm Bore = 8 in-lbs 50mm Bore = 24 in-lbs 63mm Bore = 24 in-lbs 80mm Bore = 240 in-lbs �00mm Bore = 324 in-lbs �25mm Bore = 540 in-lbs

• Maximum Operating Temperature: +�4°F to +�67°F

• Maximum Cylinder Operating Speed: 5 feet per second1Signal pressure to port on locking device. Operation at pressures lower than 58 psi may lead to inadvertent engagement of the rod lock device.

Specifications• Bore sizes 32-200mm• Max stroke 2800mm• Rod Ends – 2 standard, specials to order• Single rod end and double rod end styles• Working pressure Max �0 Bar (�45 PSI) • Working temperature min max Standard -4°F +�76°F High temp version +�4°F +250°F Aluminum piston is required for service above +�76°F• Greased for life (non-lube), does not normally need additional lubrication. If air line lubrication is initiated, it must always be continued. • Working medium: Dry, filtered compressed air to ISO 8573-� class 3. 4. 3. or better

6-2 Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

Piston Style

Cushions

Piston Material

Composite 1 Aluminum 2

None M Y

Cush B/E – 3 4

Cush head J 5

Cush cap K 6

Version

Cylinder Body Profile

Rod Lock

NoneFitted w/ Std Rod Lock 7

Fitted w/ Manual Override

Rod Lock 7

Die Cast End Caps

Standard S L N/A

Tie Rod 4 T M N/A

Clean C D N/A

Removable Gland 5 (Machined Endcaps)

Standard G R J

Tie Rod E 7 4 Consult Factory

Special 6

Any Special /

4 Not available for 160-200mm bores.

5 When Removable Gland Version is fitted with rod lock, gland cannot be replaced without disassembling cylinder.

6 If special cylinder is ordered (other than rod end), End Cap Style, Cylinder Body Profile and Rod Lock option must be given in addition to the special request.

7 Cylinders fitted with rod locks must be cushioned on both ends.

Bore Size032 32mm040 40mm050 50mm063 63mm080 80mm100 100mm125 125mm160 160mm 8

200 200mm 8

Function

Fastener Type Rod Wiper StyleDoubleActing

Double Rod Tandem

Standard endcover screws

Std scraper M F CMetal scraper Q R J

Stainless steelend cover screws 4

Std scraper A G N/AMetal scraper S T N/A

m –032

Piston Rod & Seal Material

Piston Rod MaterialSeal Material

Standard Fluorocarbon 9 Hydraulic 10

Chrome plated carbon steel 11 C G J

Chrome plated stainless steel 11 R D Z

Stainless steel 12 S N/A N/A

Acid-resistant stainless steel M N 11 N/A

9 If used for temperature above +176°F, aluminum piston required. Not available for Standard Version. Fluorocarbon seals for Rod Lock Versions are for chemical compatibility applications only, not for high temperature.

10 Hydraulic seal option valid for Removable Gland Version only. Adjustable cushion options and Rod Lock Versions not available.

11 Not available on Clean Version.

12 Only available on Clean Version.

1 Not available for 160-200mm bores.2 Not available on Clean Version.3 Must be placed in model code.

* Not available on Clean Version.

P1D – S C

Cylinder Ports Front & Rear

– BSPP Ports (G Threads)

E NPTF Ports*

Q BSPT Ports (RC Threads)*

Continued on next page


PneumatiC CylinDerS

P1D SerieS - How to orDer

8 Tie Rod Version E must be specified for these bores.


Catalog PH00�/NA

Cylinders

6


PneumatiC CylinDerS

P1D SerieS - How to orDer

Rod Mountings & Plugs 2

Rod Mounting No Plugs 3 With Plugs 4

Swivel rod eye S A

Swivel rod eye SS T 1

Swivel rod eye with clevis bracket GA V E

Swivel rod eye SS with clevis bracket GA W 2

Clevis C B

Clevis SS D 3

Flexco coupling F G

One additional piston rod nut X P

Stainless steel piston rod nut Y 4

Acid-resistant nut Z 5

None (piston rod nut only) N R

Stroke 1

Specify whole mm using 4 digits, i.e.

0500

Mounting Style

Standard Rotated 90°

Flange MF1/MF2 in front end 1 3

Flange MF1/MF2 in rear end B 4

Flange MF1/MF2 in both ends 2 K

Foot brackets MS1 F R

Clevis bracket GA aluminum C U

Rear eye MP4 aluminum E V

Rear swivel eye MP6 aluminum S W

Clevis bracket MP2 aluminum T Y

Rear eye + clevis (MP4 + MP2) aluminum L Z

Clevis bracket MP2 + pivot hinge aluminum X 5

Clevis bracket GA aluminum + steel swivel hinge Q 0

Rear swivel eye + clevis bracket GA aluminum M A

Cylinder trunnion MT4 (requires XV dimension) G 7

Trunnion flange in front end 4 H P

Trunnion flange in rear end 4 J 8

None (MX0) N 9

Sensors 5

Prepared for Factory-fitted Sensors

Cable LocationFront or

LeftRear or Right

Front & Rear

P1D Clean Version 6 7 8

P1D all versions (except Clean) prepared for sensors or Clean

Version without sensor capability 6N

Rod End

N Metric male

6 Metric female

3 Special*

0500 n n n n

Notes:

1 When specifying a stop tube, place a “/” in the version field. Then specify the version, amount of stop tube and amount of net stroke. The stroke used in the model code should be gross stroke (net stroke plus stop tube).

2 Please review Piston Rod Selection Chart in the Engineering Section to check for a rod buckling condition.

3 Clean Version comes standard with plugs. Use this column when ordering Clean Version.

4 Not available for 160-200mm bores.

5 For sensor part numbers and specifications, please refer to Electronic Sensors section.

6 P1D Clean Version ordered without sensors cannot be retrofitted with sensor capability.

n

Double rod CylindersDouble rod option is available with Mounting Styles MX0, MS�, MF�, MF2 and MT4.

For double rod cylinders, it is assumed that the rod number and rod end are the same for both piston rods. On a double rod cylinder where the two rod ends are different, use a rod end of ‘3’ and be sure to clearly state which rod end is to be assembled at which end.

* Please provide desired dimensions for KK, AM and WH. If otherwise special, provide dimensioned sketch.


Catalog PH00�/NA

Cylinders

PneumatiC CylinDerS

P1D SerieS - material SPeCifiCationS


Standard VersionBody extrusion Clear anodized aluminium End covers Powder coated or black anodized aluminumEnd cover inserts POM End cover nuts/screws Zinc plated steel 8.8 Piston rod nut Zinc plated steelPiston rod Chrome-plated steel (standard)Scraper ring PUR Piston rod bearing POM Piston POM Piston bearing POMMagnetic ring Plastic bound magnetic materialPiston fastener Zinc plated steelPiston seal PUR O-rings Nitrile rubber, NBR End-of-stroke bumpers and end seals PUR Cushioning seals PUR Cushioning screws PA

Piston rod material options(or with equivalent properties):Standard Case-hardened, chrome plated carbon steelChrome plated stainless steel �7-4 PH, chrome plated stainless steelStainless steel 303 stainless steelAcid-resistant stainless steel 3�6 stainless steel

additional/Substitute SpecificationsP1D Clean Version Transparent molding SiliconeTransparent cover ABS Screws, sensor system Stainless steelUpper seal, cover EPDM Lower seal, cover rubber Sealing plugs PA Piston rod nut Stainless steel

P1D tie-rod VersionTie-rods Blackened steel

P1D removable Gland VersionEnd covers Black anodized aluminumEnd cover screws Zinc plated steel 8.8 (32-�25mm bores)Cylinder Body Clear anodized aluminumRod gland PTFE filled high strength bronzeRod seal Buna Nitrile for sealing actionRod wiper Buna Nitrile for wiping actionPiston rod Case hardened chrome-plated steelPiston rod nut Zinc plated steelPiston POM (standard) Aluminum (optional)Piston seals PURPiston bearing POM or Molyguard wear band for aluminum pistonMagnetic ring Plastic bound magnetic materialPiston fastener Zinc plated steel (32-�25mm bores)O-rings Buna NitrileCushioning seals PURCushioning screws Stainless steel (brass for �60 and 200mm bores)

Design Variants for removable Gland VersionHigh temperature option includes: All seals Fluorocarbon Piston Aluminum (without magnetic ring)

Low pressure hydraulic option includes: Rod seal Buna Nitrile Rod wiper PUR Piston seals Buna Nitrile Piston Aluminum (non-cushioned)

Metallic Rod Scraper includes: Rod wiper Dual high strength bronze wipers with nitrile or fluorocarbon energizer


Catalog PH00�/NA

Cylinders

6


PneumatiC CylinDerS

P1D SerieS - teCHniCal Data

iSo 8573-1 Quality Classes

QualityClass

Pollution Water Oil

Particle Size (µm)

Max. Concentration

(mg/m3)

Max Pressure Dew Point

(°F)

Max. Concentration

(mg/m3)

1 0.1 0.1 -94 0.01

2 1 1 -40 -0.1

3 5 5 -4 1.0

4 15 8 +37 5.0

5 40 10 +44 25

6 – – +50 –

recommended air Quality for Cylinders For best possible service life and trouble-free operation, ISO 8573-� quality class 3.4.3 should be used. This means 5 µm filter (standard filter) dew point +37°F for indoor operation (a lower dew point should be selected for outdoor operation) and oil concentration �.0 mg oil/m3, which is what a standard compressor with a standard filter gives.

�. Lock valve must be maintained energized during cylinder motion, otherwise rod lock is engaged and cylinder valve shifts to mid position.

2. Cylinder valve must be maintained energized during extend or retract. Also keep energized at end of stroke until change of direction is desired.

3. Mid position of 5/3 Cylinder valve may be pressurized outlets if the combination of pressure load on the cylinder and inertia effects of the attached load do not exceed the holding force rating of the rod lock device, including allowance for wear.

4. Do not use cylinder lines for any logic functions — pressure levels vary too much.

3/2 LOCK VALVE (internal pilot)

Auxiliary Supply

Main Supply

5/3 CYLINDER VALVE

(external pilot)

ConnectionThe signal air for the locking device can be obtained directly from a main air supply, or from the air supply serving the valve that controls the cylinder itself. For controlled ON/OFF operation of the locking device, a separate quick-venting valve is used.

The piston rod should not be moving when the locking device is activated. The locking device is not intended to brake a movement in repeated sequences.

Holding forces

Bore SizeHolding Forces

(N) (lbs)

32mm 550 123

40mm 860 193

50mm 1345 303

63mm 2140 481

80mm 3450 755

100mm 5390 1211

125mm 8425 1894 NOTE: All P1D Rod Lock Versions are not intended for use in water service applications, or in environments that have high humidity levels and/or splashing fluids present.

P1D rod lock Version – rod lock Data


Catalog PH00�/NA

Cylinders

PneumatiC CylinDerS



Guide for Selecting Suitable tubingThe selection of the correct size of tubing is often based on experience, with no great thought to optimizing energy efficiency and cylinder velocity. This is usually acceptable, but making a rough calculation can result in worthwhile economic gains.

the following is the basic principle:�. The primary line to the working valve could be

over sized (this does not cause any extra air consumption and consequently does not create any extra costs in operation).

2. The tubes between the valve and the cylinder should, however, be optimized according to the principle that an insufficient bore throttles the flow and thus limits the cylinder speed, while an oversized pipe creates a dead volume which increases the air consumption and filling time.

The chart below is intended to help when selecting the correct size of tube to use between the valve and the cylinder.

the following prerequisites apply: The cylinder load should be about 50% of the theoretical force (= normal load). A lower load gives a higher velocity and vice versa. The tube size is selected as a function of the cylinder bore, the desired cylinder velocity and the tube length between the valve and the cylinder.

If you want to use the capacity of the valve to its maximum, and obtain maximum speed, the tubing should be chosen so that they at least correspond with the equivalent restriction diameter (see description below), so that the tubing does not restrict the total flow. This means that a short tubing must have at least the equivalent restriction diameter. If the tubing is longer, choose it from the table below. Straight fittings should be chosen for highest flow rates. (Elbow and banjo fittings cause restriction.)

0.2 0.5 0.8 1.1 1.4 0 1 2 3 4 5 6 7 8 9 10

1

2

3

4

5

6

7

8

9

10

11

Ø10Ø16Ø20Ø25Ø32Ø40Ø50

Ø63

Ø80

Ø100

Ø125

14/11

–/12

–/13

–/14

–/15

–/16

12/10

10/8

8/6

6/45/34/2.7

Cylinder Ø [mm]

Equivalent throttling bore 1) Tube ØOut./ØInt. [mm]

Length of tubing [m]Cylinder speed [m/s]

Suita

ble

valv

e Qn

2) a

pp 8

00 l/

min

Suita

ble

valv

e Qn

2) a

pp 1

000

l/min

Suita

ble

area

for v

alve

with

Qn2)

app

300

0 l/m

in

1) The “equivalent throttling bore“ is a long throttle (for example a tube) or a series of throttles (for example, through a valve) converted to a short throttle which gives a corresponding flow rate. This should not be confused with the “orifice“ which is sometimes specified for valves. The value for the orifice does not normally take account of the fact that the valve contains a number of throttles.

2) Qn is a measure of the valve flow capacity, with flow measured in litre per minute (l/min) at 6 bar(e) supply pressure and 1 bar pressure drop across the valve.


Catalog PH00�/NA

Cylinders

6


PneumatiC CylinDerS


2.0

Speed [m/s]

Mass [Kg]

1.5

1.0

0.50.4

0.3

0.2

0.10.5 1 2 3 5 10 20 30 50 100 200

Ø32 Ø40 Ø50 Ø63 Ø80Ø100

Ø125

use as a BrakeThe chart to the right shows the maximum values for speed and braking mass if the cylinder is used as a brake. The cylinder should not be exposed to additional compressive forces as this significantly reduces the external mass that can be braked.

We recommend systems in which the cylinder does not act as a motor during braking. Heat is generated if the brake is used frequently, and this must be taken into account to ensure that the maximum temperature is not exceeded.


Catalog PH00�/NA

CylindersPneumatic CylindersP1D Series Standard Version

PneumatiC CylinDerS

P1D SerieS - StanDarD VerSion

AM

ØB

ØD

KK

BG

VD

G

WH

WH WH + S

L2

L12

ØD

4

PP

PL

SS

TT Ø

BA

VA

GL8 + S

RT

OA

R

E

L9 + 2 x S

DIN 439B

SW

EE

Dimensions

EECylinder

BoreAM

(mm)B

(mm)BA

(mm)BG

(mm)D

(mm)D4

(mm) E BSPPNPTF/BSPT

G(mm) KK

L2(mm)

L8(mm)

L9(mm)

L12(mm)

32 22 30 30 16 12 45.0 50.0 G1/8 1/8 28.5 M10x1.25 16.0 94 146 6.0

40 24 35 35 16 16 52.0 57.4 G1/4 1/4 33.0 M12x1.25 19.0 105 165 6.5

50 32 40 40 16 20 60.7 69.4 G1/4 1/4 33.5 M16x1.5 24.0 106 180 8.0

63 32 45 45 16 20 71.5 82.4 G3/8 3/8 39.5 M16x1.5 24.0 121 195 8.0

80 40 45 45 17 25 86.7 99.4 G3/8 3/8 39.5 M20x1.5 30.0 128 220 10.0

100 40 55 55 17 25 106.7 116.0 G1/2 1/2 44.5 M20x1.5 32.4 138 240 10.0

125 54 60 60 20 32 134.0 139.0 G1/2 1/2 51.0 M27x2 45.0 160 290 13.0

Cylinder Bore

OA(mm)

PL(mm)

PP(mm)

R(mm) RT

SS(mm)

SW(mm)

TT(mm)

VA(mm)

VD(mm)

WH(mm)

32 6 13 21.8 32.5 M6 4.0 10 4.5 3.5 4.5 26

40 6 14 21.9 38.0 M6 8.0 13 5.5 3.5 4.5 30

50 8 14 25.9 46.5 M8 4.0 17 7.5 3.5 4.5 37

63 8 16 27.4 56.5 M8 6.5 17 11.0 3.5 4.5 37

80 6 16 30.5 72.0 M10 0 22 15.0 3.5 4.5 46

100 6 18 35.8 89.0 M10 0 22 20.0 3.5 4.5 51

125 8 23 40.5 110.0 M12 0 27 17.5 3.5 6.5 65

S = Stroke

tolerancesCylinder

Bore BBA

(mm)L8

(mm)L9

(mm)R

(mm) Stroke Tolerance

32 d11 d11 ±0.4 ±2 ±0.5 +1/-0

40 d11 d11 ±0.7 ±2 ±0.5 +1/-0

50 d11 d11 ±0.7 ±2 ±0.6 +1/-0

63 d11 d11 ±0.8 ±2 ±0.7 +1/-0

80 d11 d11 ±0.8 ±3 ±0.7 +1/-0

100 d11 d11 ±1.0 ±3 ±0.7 +1/-0

125 d11 d11 ±1.0 ±3 ±1.1 +1/-0

AM

ØB

ØD

KK

BG

VD

G

WH

WH WH + S

L2

L12

ØD

4

PP

PL

SS

TT Ø

BA

VA

GL8 + S

RT

OA

R

E

L9 + 2 x S

DIN 439B

SW

EE

6-� Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1D Series removable Gland Version

PneumatiC CylinDerS

P1D SerieS - remoVaBle GlanD VerSion

DimensionsEE

Cylinder Bore

AM(mm)

B(mm)

BA(mm)

BG(mm)

D(mm)

D4(mm)

E(mm) BSPP

NPTF/BSPT

G(mm) KK

L2(mm)

L8(mm)

L9(mm)

L12(mm)

32 22 30 30 16 12 45.0 46.5 G1/8 1/8 28.5 M10x1.25 18 94 146 6.0

40 24 35 35 16 16 52.0 52.0 G1/4 1/4 33.0 M12x1.25 20 105 165 6.5

50 32 40 40 16 20 60.7 63.5 G1/4 1/4 33.5 M16x1.5 26 106 180 6.5

63 32 45 45 16 20 71.5 76.0 G3/8 3/8 39.5 M16x1.5 26 121 195 6.5

80 40 45 45 17 25 86.7 95.5 G3/8 3/8 39.5 M20x1.5 33 128 220 10.0

100 40 55 55 17 25 106.7 114.5 G1/2 1/2 44.5 M20x1.5 33 138 240 10.0

125 54 60 60 20 32 134.0 140.0 G1/2 1/2 51.0 M27x2 41 160 290 13.0

Cylinder Bore

OA(mm)

PL(mm)

PP(mm)

R(mm) RT

SS(mm)

SW(mm)

TT(mm)

VA(mm)

VD(mm)

WH(mm)

32 6 13 21.8 32.5 M6 6.5 10 4.5 3.5 4.5 26

40 6 14 21.9 38.0 M6 8.0 13 5.5 3.5 4.5 30

50 8 14 25.9 46.5 M8 4.0 17 7.5 3.5 4.5 37

63 8 16 27.4 56.5 M8 6.5 17 11.0 3.5 4.5 37

80 6 16 30.5 72.0 M10 0 22 15.0 3.5 4.5 46

100 6 18 35.8 89.0 M10 0 22 20.0 3.5 4.5 51

125 8 23 40.5 110.0 M12 0 27 17.5 5.5 6.5 65S = Stroke

tolerances

Cylinder Bore B

BA(mm)

L8(mm)

L9(mm)

R(mm) Stroke Tolerance

32 d11 d11 ±0.4 ±2 ±0.5 +1/-0

40 d11 d11 ±0.7 ±2 ±0.5 +1/-0

50 d11 d11 ±0.7 ±2 ±0.6 +1/-0

63 d11 d11 ±0.8 ±2 ±0.7 +1/-0

80 d11 d11 ±0.8 ±3 ±0.7 +1/-0

100 d11 d11 ±1.0 ±3 ±0.7 +1/-0

125 d11 d11 ±1.0 ±3 ±1.1 +1/-0

AM L12

ØB

ØD KK

DIN 439B

SW

VD

L2 G

WH L + S8

G

VAØD4

ØBA

PL

PP

EE OA

RT

E

R

BG

WH

L + 2 x S

WH + S

9

SS

TT

AM L12

ØB

ØD KK

DIN 439B

SW

VD

L2 G

WH L + S8

G

VAØD4

ØBA

PL

PP

EE OA

RT

E

R

BG

WH

L + 2 x S

WH + S

9

SS

TT

6-�0 Parker Hannifin Corporation

Catalog PH00�/NA

CylindersPneumatic CylindersP1D Series rod lock Version r or 7

PneumatiC CylinDerS

P1D SerieS - roD loCk VerSion r or 7

DimensionsCylinder

Bore A

(mm) AM

(mm)B

(mm) BA

(mm)BG

(mm) D

(mm)D4

(mm)E

(mm) EE G

(mm)H

(mm) KK L

(mm) L8

(mm)L12

(mm)

32 16 22 30 30 16 12 45.0 46.5 G1/8 28.5 71.5 M10x1.25 56.0 137 6.0

40 16 24 35 35 16 16 52.0 52.0 G1/4 33.0 77.0 M12x1.25 56.0 149 6.5

50 18 32 40 40 16 20 60.7 63.5 G1/4 33.5 80.5 M16x1.5 62.5 153 6.5

63 26 32 45 45 16 20 71.5 76.0 G3/8 39.5 96.5 M16x1.5 74.5 178 6.5

80 35 40 45 45 17 25 86.7 95.5 G3/8 39.5 110.5 M20x1.5 87.0 199 10.0

100 50 40 55 55 17 25 106.7 114.5 G1/2 44.5 132.5 M20x1.5 106.0 226 10.0

125 60 54 60 60 20 32 134.0 140.0 G1/2 51.0 145.0 M27x2 117.0 254 13.0

Cylinder Bore

OA(mm)

P (mm)

PL (mm)

PP(mm)

R (mm)

RT (mm)

S (mm)

SS (mm)

SW(mm)

T (mm)

TT (mm)

VA (mm)

VD(mm)

WH(mm)

32 6 64.8 13 21.8 32.5 M6 7 6.5 10 2.5 4.5 3.5 4.5 15

40 6 68.0 14 21.9 38.0 M6 9 8.0 13 2.0 5.5 3.5 4.5 16

50 8 73.5 14 25.9 46.5 M8 8 4.0 17 4.0 7.5 3.5 5.0 17

63 8 89.5 16 27.4 56.5 M8 8 6.5 17 2.0 11.0 3.5 5.0 17

80 – 101.5 16 30.5 72.0 M10 9 0 22 5.0 15.0 3.5 4.0 20

100 – 123.5 18 35.8 89.0 M10 12 0 22 6.0 20.0 3.5 4.0 20

125 – 136.0 23 40.5 110.0 M12 12 0 27 6.0 17.5 5.5 6.0 27

tolerancesCylinder

Bore B

(mm)R

(mm)L8

(mm) BA

(mm)Stroke-Length Tolerance

(mm)

32 d11 ±0.5 ±0.4 d11 +1/-0

40 d11 ±0.5 ±0.7 d11 +1/-0

50 d11 ±0.6 ±0.7 d11 +1/-0

63 d11 ±0.7 ±0.8 d11 +1/-0

80 d11 ±0.7 ±0.8 d11 +1/-0

100 d11 ±0.7 ±1.0 d11 +1/-0

125 d11 ±1.1 ±1.0 d11 +1/-0

12

8

4VD

A

L

P

WH

L + Stroke

H

ØD

T

STT

SS

ØBA

KK

ØD

ØB

AM L

BG

EE

VAG

PLPP

OA

RT

R

E

6G1/8

DIN 439BSW

(M5 Ø32 - Ø40)G 1/8 Ø50 - Ø125)

6-�� Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1D Series rod lock Version J w/ manual override

PneumatiC CylinDerS

P1D SerieS - roD loCk VerSion J witH manual oVerriDe

DimensionsCylinder

BoreA

(mm)AM

(mm)B

(mm)BA

(mm)BG

(mm)D

(mm)D4

(mm)E

(mm) EEG

(mm)H

(mm) KKL

(mm)L8

(mm)L12

(mm)MR1(mm)

MR2(mm)

32 27.0 22 30 30 16 12 45.0 46.5 G1/8 28.5 71.5 M10X1.25 56.0 137 6.0 16.0 3.0

40 27.0 24 35 35 16 16 52.0 52.0 G1/4 33.0 77.0 M12X1.25 56.0 149 6.5 16.0 3.0

50 21.5 32 40 40 16 20 60.7 63.5 G1/4 33.5 80.5 M16X1.5 62.5 153 6.5 18.5 5.5

63 39.0 32 45 45 16 20 71.5 76.0 G3/8 39.5 96.5 M16X1.5 74.5 178 6.5 22.0 4.0

80 48.5 40 45 45 17 25 86.7 95.5 G3/8 39.5 120.5 M20X1.5 97.0 199 10.0 15.0 19.8

100 65.0 40 55 55 17 25 106.7 114.5 G1/2 44.5 142.5 M20X1.5 116.0 226 10.0 15.0 20.8

125 71.0 54 60 60 20 32 134.0 140.0 G1/2 51.0 155.0 M27X2 127.0 254 13.0 19.0 23.0

Cylinder Bore

N (mm)

NR(mm)

OA (mm)

P (mm)

PL (mm)

PP(mm)

R (mm) RT

S (mm)

SS (mm)

SW(mm)

T (mm)

TT(mm)

VA(mm)

VD (mm)

WH(mm)

32 8 10.0 6 64.8 13 21.8 32.5 M6 7 6.5 10 2.5 4.5 3.5 4.5 15

40 8 10.0 6 68.0 14 21.9 38.0 M6 9 8.0 13 2.0 5.5 3.5 4.5 16

50 10 12.0 8 73.5 14 25.9 46.5 M8 8 4.0 17 4.0 7.5 3.5 5.0 17

63 10 12.0 8 89.5 16 27.4 56.5 M8 8 6.5 17 2.0 11.0 3.5 5.0 17

80 11 12.5 – 111.5 16 30.5 72.0 M10 9 0 22 5.0 15.0 3.5 14 30

100 11 12.5 – 133.5 18 35.8 89.0 M10 12 0 22 6.0 20.0 3.5 14 30

125 11 12.5 – 146.0 23 40.5 110.0 M12 12 0 27 6.0 17.5 5.5 16 37

tolerancesCylinder

Bore B

(mm)R

(mm)L8

(mm)BA

(mm)Stroke-Length Tolerance

(mm)

32 d11 ±0.5 ±0.4 d11 +1/-0

40 d11 ±0.5 ±0.7 d11 +1/-0

50 d11 ±0.6 ±0.7 d11 +1/-0

63 d11 ±0.7 ±0.8 d11 +1/-0

80 d11 ±0.7 ±0.8 d11 +1/-0

100 d11 ±0.7 ±1.0 d11 +1/-0

125 d11 ±1.1 ±1.0 d11 +1/-0

12

8

4

1

2

WH

SSKK

L

G

PP

DIN 439B

SW

L + Stroke

ØD

TT

ØBA

ØD

AM

VA

PLOA

RT

R

E

MR

N HEX

6

(M5 Ø32 & Ø40)(G1/8" Ø50-Ø125)

ØB

MR

AL

P

S

T

EE

MOUNTING SURFACE

BG

(M5 Ø32 & Ø40)(G1/8" Ø50-Ø125)

NR

H

VD


Catalog PH00�/NA

Cylinders

PneumatiC CylinDerS

P1D SerieS - tie-roD VerSion (160-200mm)

DimensionsEE

Cylinder Bore

AM(mm)

Bd11

(mm)BG

(mm)DD E

(mm) BSPPNPTF/BSPT

G(mm)

MM(mm)

TG(mm)

VD(mm)

VE(mm)

WH(mm)

Y(mm)

PJ 1

(mm)ZJ 1

(mm)ZM 2

(mm)

160 72 65 24 M16 177 G3/4 3/4 54 40 140 6 56 80 105 130 260 340

200 72 75 24 M16 214 G3/4 3/4 54 40 175 6 56 95 120 130 275 370

� Add stroke2 Add 2×stroke

E

E TG

TGDD

B MM

VE

G

BG

ZJ + STROKE

EE G VD

B

PJ + STROKEY

WH

VD

Rod End #1 Rod End #2

MM

AM

VE G

ZJ + STROKE

EE

WH

Y

ZM + (2 x STROKE)

PJ + STROKE

G VE

WH + STROKE

AM

MM

Double rod CylindersDouble rod option is available on Mounting Styles MX0, MS�, MF�, MF2 and MT4.

For double rod cylinders, it is assumed that the rod number and rod end are the same for both piston rods. On a double rod cylinder where the two rod ends are different, use a rod end of ‘3’ and be sure to clearly state which rod end is to be assembled at which end.

Pneumatic CylindersP1D Series tie-rod Version

PneumatiC CylinDerS

P1D SerieS - tie-roD VerSion (32-125mm)

DimensionsCylinder

BoreD5

(mm)D6

(mm)D7

(mm)E1

(mm)E2 max(mm)

32 36 5.3 49.6 32 5

40 45 5.3 57.3 36 6

50 55 7.1 69.3 42 6

63 68 7.1 82.3 49 5

80 85 8.9 99.3 57 5

100 105 8.9 117.6 68 6

125 132 10.7 142.8 81 6

AM

ØB

ØD

KK

VD

G

WH

L2

L12

PPE2 maxPL

SS

TT Ø

BA

VA

GL8 + S

RT

OA

R

E

E 1

DIN 439B

SW

EE

ØD

7

AM

ØB

ØD

KK

VD

G

WH

L2

L12

ØD

5

ØD

6

PP

PL

SS

TT Ø

BA

VAG

L8 + S

RT

OA

R

E

DIN 439B

SW

EE

P1D tie-rod Version (32-125mm) P1D Clean Version


Catalog PH00�/NA

Cylinders

6

CylinderBore

A (mm)

P1D-T P1D-S

32 247 256

40 277 286

50 293 306

63 323 336

80 355 373

100 385 403

125 461 –

S = Stroke

3 position: A + 2 x S4 position: A + S1 + S2

Pneumatic CylindersP1D Series Duplex

PneumatiC CylinDerS

P1D SerieS DuPlex CylinDerS

General Description: 3 and 4 Position Cylinders This type of cylinder function consists of two cylinders installed back to back. Two cylinders with the same stroke give a 3 position cylinder with a symmetrical centre position, whereas different strokes give a 4 position cylinder where the two central positions can be calculated from the different stroke lengths.

3 and 4 position cylinders can be ordered in two ways.

factory-fitted P1D-t P�D Tie-Rod Version cylinders are completed at the factory and are joined together as one unit by special tie-rods. See function options in model code.

installation kit for all Designs There is an installation kit for cylinder bores 32 – �00 mm which makes it possible to join any two P�D cylinders together at any time to make a 3 or 4 position cylinder.


Catalog PH00�/NA

Cylinders

WHSWWRENCHFLATS

BC NA KK

L12

AM L2

VD

D B

WHSWWRENCHFLATS

BC NA KF

L12

AM

L2

VD

D B

Thread Style N Thread Style 6 “Special Thread”Style 3Special thread, extension, rod eye, blank, etc are also available. To order, specify “Style 3” and provide desired dimensions for KF or KK, AM and WH. If otherwise special, furnish dimensioned sketch.

Bore D KK KF AMB

d11 BCSW

across flats L12 NA VD L2 WH

32 12 M10x1.25 M8x1 22 30 27 10 6 11 4.5 18 26

40 16 M12x1.25 M10x1.25 24 35 32 13 6.5 15 4.5 20 30

50 20 M16x1.5 M14x1.5 32 40 36 17 6.5 19 4.5 26 37

63 20 M16x1.5 M14x1.5 32 45 36 17 6.5 19 4.5 26 37

80 25 M20x1.5 M18x1.5 40 45 41 22 10 24 4.5 33 46

100 25 M20x1.5 M18x1.5 40 55 41 22 10 24 4.5 33 51

125 32 M27x2 M24x2 54 60 50 27 13 31 6.5 41 65

160 40 M36x2 M30x2 72 65 60 36 16 39 6 56 80

200 40 M36x2 M30x2 72 75 60 36 16 39 6 56 95

NOTE: Dimensions do not apply to Rod Lock Versions.

Pneumatic Cylinder MountingsP1D Series all mountings except mf1

CylinDer mountinGS

P1D SerieS - all mountinGS exCePt mf1


Catalog PH00�/NA

Cylinders

6

MFW

SWWRENCHFLATS

NA KK

L12

AM

D

L2

WH

MFW

SWWRENCHFLATS

NA KF

L12

AM

D

L2

WH

Bore D KK KF AMSW

across flats L12 MF NA L2 W WH

32 12 M10x1.25 M8x1 22 10 6 10 11 18 16 26

40 16 M12x1.25 M10x1.25 24 13 6.5 10 15 20 20 30

50 20 M16x1.5 M14x1.5 32 17 6.5 12 19 26 25 37

63 20 M16x1.5 M14x1.5 32 17 6.5 12 19 26 25 37

80 25 M20x1.5 M18x1.5 40 22 10 16 24 33 30 46

100 25 M20x1.5 M18x1.5 40 22 10 16 24 33 35 51

125 32 M27x2 M24x2 54 27 13 20 31 41 45 65

160 40 M36x2 M30x2 72 36 16 20 39 56 60 80

200 40 M36x2 M30x2 72 36 16 25 39 56 70 95

Thread Style N Thread Style 6 “Special Thread”Style 3Special thread, extension, rod eye, blank, etc are also available. To order, specify “Style 3” and provide desired dimensions for KF or KK, AM and WH. If otherwise special, furnish dimensioned sketch.

NOTE: Dimensions do not apply to Rod Lock Versions.

Pneumatic Cylinder MountingsP1D Series mf1 mounting

CylinDer mountinGS

P1D SerieS - mf1 mountinG


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1D Series flange mf1/mf2 - foot Bracket mS1

CylinDer mountinGS

P1D SerieS - flanGe mf1/mf2

According to ISO MF�/MF2, VDMA 24 562, AFNOR

Part No.Bore(mm)

d1H11

(mm)

FBH13

(mm)TG1

(mm)E

(mm)

RJS14(mm)

MFJS14 (mm)

TF JS14(mm) UF

I1-0.5

(mm)W

(mm)ZF

(mm) ZB

(mm)

P1C-4KMBA 32 30 7 32.5 45 32 10 64 80 5.0 16 130 123.5

P1C-4LMBA 40 35 9 38.0 52 36 10 72 90 5.0 20 145 138.5

P1C-4MMBA 50 40 9 46.5 65 45 12 90 110 6.5 25 155 146.5

P1C-4NMBA 63 45 9 56.5 75 50 12 100 120 6.5 25 170 161.5

P1C-4PMBA 80 45 12 72.0 95 63 16 126 150 8.0 30 190 177.5

P1C-4QMBA 100 55 14 89.0 115 75 16 150 170 8.0 35 205 192.5

P1C-4RMB 125 60 16 110.0 140 90 20 180 205 10.5 45 245 230.5

L075370160 160 65 18 140.0 190 115 20 230 279 7.0 60 280 266

L075370200 200 75 22 175.0 228 135 25 270 318 13.0 70 300 281

S = Stroke length

ØF

B

R

UF

Ød1 TF

E

TG1

ZB+S

MFMF

W

ZF+S

I1

Intended for fixed mounting of cylinder. Flange can be fitted to front or rear end cover of cylinder.Materials 32-100mm bore flange: Surface-treated aluminum, black 125-200mm bore flange: Steel, black Mounting screws acc. to DIN 6912: Zinc-plated steel 8.8Supplied complete with mounting screws for attachment to cylinder.

ØF

B

R

UF

Ød1 TF

E

TG1

ZB+S

MFMF

W

ZF+S

I1

CylinDer mountinGS

P1D SerieS - foot BraCket mS1

According to ISO MS�, VDMA 24 562, AFNOR

Part No.Bore(mm)

ABH14

(mm)TG1

(mm)E

(mm)

TRJS14(mm)

AO (mm)

AU (mm)

AH JS15 (mm)

I7 (mm)

AT (mm)

I9JS14(mm)

SA (mm)

P1C-4KMF 32 7 32.5 45 32 10 24 32 30 4.5 17.0 142

P1C-4LMF 40 9 38.0 52 36 8 28 36 30 4.5 18.5 161

P1C-4MMF 50 9 46.5 65 45 13 32 45 36 5.5 25.0 170

P1C-4NMF 63 9 56.5 75 50 13 32 50 35 5.5 27.5 185

P1C-4PMF 80 12 72.0 95 63 14 41 63 49 6.5 40.5 210

P1C-4QMF 100 14 89.0 115 75 15 41 71 54 6.5 43.5 220

P1C-4RMF 125 16 110.0 140 90 22 45 90 71 8.0 60.0 250

L075380160 160 18 140.0 177 115 24 60 115 63.5 4.75 63.5 300

L075380200 200 22 175.0 214 135 30 70 135 65 8.0 65.0 320

S = Stroke length

SA+S

ØAB

AU AO

AT

E

TGI

IAH

TR

7

Intended for fixed mounting of cylinder. Foot bracket can be fitted to front and rear end covers of cylinder.Materials Foot bracket: Surface-treated steel, black Mounting screws acc. to DIN 912: Zinc-plated steel 8.8Supplied in pairs with mounting screws for attachment to cylinder.

SA+S

ØAB

AU AO

AT

E

TGI

IAH

TR

7


Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1D Series Pivot Bracket w/ rigid Bearing - Swivel eye Bracket mP6

CylinDer mountinGS

P1D SerieS - PiVot BraCket witH riGiD BearinG

According to CETOP RP �07 P, VDMA 24 562, AFNOR

Part No.Bore(mm)

CKH9

(mm)

S5H13

(mm)

K1JS14(mm)

K2G1

JS14(mm)

G2JS14(mm)

EM(mm)

G3(mm)

CAJS15(mm)

H6(mm)

R1(mm)

P1C-4KMD 32 10 6.6 38 51 21 18 25.5 31 32 8 10.0

P1C-4LMD 40 12 6.6 41 54 24 22 27.0 35 36 10 11.0

P1C-4MMD 50 12 9.0 50 65 33 30 31.0 45 45 12 13.0

P1C-4NMD 63 16 9.0 52 67 37 35 39.0 50 50 12 15.0

P1C-4PMD 80 16 11.0 66 86 47 40 49.0 60 63 14 15.0

P1C-4QMD 100 20 11.0 76 96 55 50 59.0 70 71 15 19.0

P1C-4RMD 125 25 14.0 94 124 70 60 69.0 90 90 20 22.5

L075480160 160 30 14.0 118 156 97 89 88.5 126 115 25 31.0

L075480200 200 30 16.0 122 162 105 89 88.5 130 135 30 31.0

5

G

ØC

K

CA

G2

G3

�R�

H6

KK�2

SØ

EM

Intended for flexible mounting of cylinder. The pivot bracket can be combined with clevis bracket MP2.

Materials Pivot bracket: Surface-treated aluminium, black Bearing: Sintered oil-bronze bushing

CylinDer mountinGS

P1D SerieS - SwiVel eye BraCket mP6

According to VDMA 24 562, AFNOR

Part No.Bore(mm)

E(mm)

B1(mm)

B2(mm)

EN(mm)

R1(mm)

R2(mm)

FL(mm)

I2(mm)

L(mm)

CNH7

(mm)XD

(mm) Z

P1C-4KMSA 32 45 10.5 – 14 16 – 22 5.5 12 10 142 4°

P1C-4LMSA 40 52 12.0 – 16 18 – 25 5.5 15 12 160 4°

P1C-4MMSA 50 65 15.0 51 21 21 19 27 6.5 15 16 170 4°

P1C-4NMSA 63 75 15.0 – 21 23 – 32 6.5 20 16 190 4°

P1C-4PMSA 80 95 18.0 – 25 29 – 36 10.0 20 20 210 4°

P1C-4QMSA 100 115 18.0 – 25 31 – 41 10.0 25 20 230 4°

P1C-4RMSA 125 140 25.0 – 37 40 – 50 10.0 30 30 275 4°

L075420160 160 177 30.0 – 43 44 41 55 4.0 41 35 315 16°

L075420200 200 214 30.0 – 43 48 42 60 8.0 42 35 335 16°S = Stroke length

XD+S

ØCN

R1

L

R2

B

B

E

1

2

EN

I 2FL

ZZ

Intended for use together with clevis bracket GA Material Bracket: Surface-treated aluminium, black (Cast iron for 160-200mm bores) Swivel bearing acc. to DIN 648K: Hardened steel Supplied complete with mounting screws for attachment to cylinder.XD+S

ØCN

R1

L

R2

B

B

E

1

2

EN

I 2FL

ZZ


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1D Series Clevis Bracket mP2 - mP4

CylinDer mountinGS

P1D SerieS - CleViS BraCket mP2

According to ISO MP2, VDMA 24 562, AFNOR

Part No.Bore(mm)

C(mm)

E(mm)

UBh14

(mm)

CBH14

(mm)

FL±0.2(mm)

L(mm)

I2(mm)

CDH9

(mm)MR

(mm)XD

(mm)

P1C-4KMT 32 53 45 45 26 22 13 5.5 10 10 142

P1C-4LMT 40 60 52 52 28 25 16 5.5 12 12 160

P1C-4MMT 50 68 65 60 32 27 16 6.5 12 12 170

P1C-4NMT 63 78 75 70 40 32 21 6.5 16 16 190

P1C-4PMT 80 98 95 90 50 36 22 10.0 16 16 210

P1C-4QMT 100 118 115 110 60 41 27 10.0 20 20 230

P1C-4RMT 125 139 140 130 70 50 30 10.0 25 25 275

L075390160 160 178 177 170 90 55 36 10.0 30 30 315

L075390200 200 178 214 170 90 60 41 18.0 30 30 335

S = Stroke length

UB

CB

E

XD+S

MR

I

FL

L

2

C

Now in aluminum!

Intended for flexible mounting of cylinder. Clevis bracket MP2 can be combined with clevis bracket MP4. Materials Clevis bracket: Surface-treated aluminium, black for 32-160mm bores; Cast iron for 200mm bore Pin: Surface hardened steel Circlips according to DIN 471: Spring steel Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 Supplied complete with mounting screws for attachment to cylinder.

UB

CB

E

XD+S

MR

I

FL

L

2

C

CylinDer mountinGS

P1D SerieS - CleViS BraCket mP4


Part No.Bore(mm)

E (mm)

EW (mm)

FL (mm)

L±0.2(mm)

I2(mm)

CD(mm)

MRH9

(mm)XD

(mm)

P1C-4KME 32 45 26 22 13 5.5 10 10 142

P1C-4LME 40 52 28 25 16 5.5 12 12 160

P1C-4MME 50 65 32 27 16 6.5 12 12 170

P1C-4NME 63 75 40 32 21 6.5 16 16 190

P1C-4PME 80 95 50 36 22 10.0 16 16 210

P1C-4QME 100 115 60 41 27 10.0 20 20 230

P1C-4RME 125 140 70 50 30 10.0 25 25 275

L075410160 160 177 90 55 36 13.5 30 30 315

L075410200 200 214 90 60 41 18.0 30 30 335S = Stroke length

EW

E

XD+S

CD

MR

I

FL

L

2

Intended for flexible mounting of cylinder. Clevis bracket MP4 can be combined with clevis bracket MP2. Materials Clevis bracket: Surface-treated aluminium, black for 32-125mm bores; Cast iron for 160-200mm bores

EW

E

XD+S

CD

MR

I

FL

L

2

Mounting screws acc. to DIN 912: Zinc-plated steel 8.8 Supplied complete with mounting screws for attachment to cylinder.

6-�� Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1D Series Clevis Bracket Ga - Pin Set

CylinDer mountinGS

P1D SerieS - CleViS BraCket Ga


Part No.Bore(mm)

C (mm)

E (mm)

B2d12

(mm)

B1H14

(mm)T

(mm)B3

(mm)R2

(mm)L1

(mm)

FL±0.2(mm)

I2(mm)

L(mm)

CNF7

(mm)R1

(mm)XD

(mm)

P1C-4KMCA 32 41 45 34 14 3 3.3 17 11.5 22 5.5 12 10 11 142

P1C-4LMCA 40 48 52 40 16 4 4.3 20 12.0 25 5.5 15 12 13 160

P1C-4MMCA 50 54 65 45 21 4 4.3 22 14.0 27 6.5 17 16 18 170

P1C-4NMCA 63 60 75 51 21 4 4.3 25 14.0 32 6.5 20 16 18 190

P1C-4PMCA 80 75 95 65 25 4 4.3 30 16.0 36 10.0 20 20 22 210

P1C-4QMCA 100 85 115 75 25 4 4.3 32 16.0 41 10.0 25 20 22 230

P1C-4RMCA 125 110 140 97 37 6 6.3 42 24.0 50 10.0 30 30 30 275

L075510160 160 140 178 122 43 6 6.3 46 26.5 55 10.0 37 35 h9 36 C.F.

L075510200 200 175 218 122 43 6 6.3 49 26.5 60 11.5 40 35 h9 38 C.F.

S = Stroke length C.F. = Consult Factory

XD+S

CN

R1

L

L

R2

B

B

E

1

2

B3

T1

L2FL

C

Now in aluminium!

Bore (mm) Part Number

32 9301054311

40 9301054312

50 9301054313

63 9301054314

80 9301054315

100 9301054316

125 9301054317

Intended for flexible mounting of cylinder. Clevis bracket GA can be combined with pivot bracket with swivel bearing, swivel eye bracket and swivel rod eye.

Materials Clevis bracket: Surface-treated aluminium Pin: Surface hardened steel Locking pin: Spring steel Circlips according to DIN 471: Spring steel Mounting screws acc. to DIN 912: Zinc-plated steel 8.8

Supplied complete with mounting screws for attachment to cylinder.

XD+S

CN

R1

L

L

R2

B

B

E

1

2

B3

T1

L2FL

C

MaterialsPin: Stainless steelLocking pin: Stainless steelCirclips according to DIN 471: Stainless steel

PneumatiC CylinDerS

P1D SerieS - StainleSS Steel Pin Set Ga


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1D Series Head Detachable Clevis mP7 – Pivot Bracket w/ Swivel Bearing

CylinDer mountinGS

P1D SerieS - HeaD DetaCHaBle CleViS mP7


Part No. BoreCD

(mm)E

(mm)FL

(mm)FW

(mm)L

(mm)MR

(mm)UB

(mm)XW

(mm)

L075400032 32 10 46.5 22 8 12 10 45 4

L075400040 40 12 52 25 9 15 12 52 5

L075400050 50 12 63.5 27 10 15 13 60 10

L075400063 63 16 76 32 15 20 16 70 5

L075400080 80 16 95.5 36 20 20 17 90 10

L075400100 100 20 114.5 41 25 25 21 110 10

L075400125 125 25 140 50 30 35 25 130 15

L075400160 160 30 177 55 40 36 30 170 25

L075400200 200 30 214 60 40 41 30 170 35

E

E

FWUB

X

XW

MR

CDLFL

Intended for flexible mounting of cylinder

Materials Clevis bracket: Cast iron for 32-63mm bores; Surface treated aluminum, black for 80-200mm bores Mounting screws acc. to DIN 912: Zinc-plated steel 8.8

Supplied complete with mounting screws for attachment to cylinder.

E

E

FWUB

X

XW

MR

CDLFL


Part No.Bore(mm)

CNH7

(mm)

S5H13

(mm)

K1JS14(mm)

K2(mm)

EU(mm)

G1JS14(mm)

G2JS14(mm)

EN(mm)

G3(mm)

CHJS15(mm)

H6(mm)

ER(mm) Z

P1C-4KMA 32 10 6.6 38 51 10.5 21 18 14 31 32 10 16 4°

P1C-4LMA 40 12 6.6 41 54 12.0 24 22 16 35 36 10 18 4°

P1C-4MMA 50 16 9.0 50 65 15.0 33 30 21 45 45 12 21 4°

P1C-4NMA 63 16 9.0 52 67 15.0 37 35 21 50 50 12 23 4°

P1C-4PMA 80 20 11.0 66 86 18.0 47 40 25 60 63 14 28 4°

P1C-4QMA 100 20 11.0 76 96 18.0 55 50 25 70 71 15 30 4°

P1C-4RMA 125 30 14.0 94 124 25.0 70 60 37 90 90 20 40 4°

5

G

ØC

N

CH

G2

G3

�ER

H6

KK�2

SØ

EU

ZZ

EN

CylinDer mountinGS

P1D SerieS - PiVot BraCket witH SwiVel BearinG

Intended for use together with clevis bracket GA.

Material Pivot bracket: Surface-treated steel, black Swivel bearing acc. to DIN 648K: Hardened steel

6-2� Parker Hannifin Corporation

Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1D Series Head Detachable Clevis mP7 – Pivot Bracket w/ Swivel Bearing

Pneumatic Cylinder MountingsP1D Series mounting kit - Pivot Bracket for mt4

CylinDer mountinGS

P1D SerieS - mountinG kit

Part No.Bore(mm)

E(mm)

TG(mm)

ØFB(mm)

MF(mm)

A(mm)

ØBA(mm)

P1E-6KB0 32 50 32.5 6.5 5 16 30

P1E-6LB0 40 60 38.0 6.5 5 16 35

P1E-6MB0 50 66 46.5 8.5 6 20 40

P1E-6NB0 63 80 56.5 8.5 6 20 45

P1E-6PB0 80 100 72.0 10.5 8 25 45

P1E-6QB0 100 118 89.0 10.5 8 25 55

E

TG

ØFBETG

A

MF

ØBA

E

TG

ØFB

ETG

A

MF

ØBA

Mounting kit for back to back mounted cylinders, 3 and 4 position cylinders.

Material Mounting: Aluminium Mounting screws: Zinc-plated steel 8.8

According to ISO, VDMA 24 562, AFNOR

Part No.Bore(mm)

B1(mm)

B2(mm)

A(mm)

C(mm)

d1(mm)

d2H13

(mm)H1

(mm)H2

(mm)

fx45°min

(mm)

9301054261 32 46 18.0 32 10.5 12 6.6 30 15 1.0

9301054262 40 55 21.0 36 12.0 16 9.0 36 18 1.6

50 55 21.0 36 12.0 16 9.0 36 18 1.6

9301054264 63 65 23.0 42 13.0 20 11.0 40 20 1.6

80 65 23.0 42 13.0 20 11.0 40 20 1.6

9301054266100 75 28.5 50 16.0 25 14.0 50 25 2.0

125 75 28.5 50 16.0 25 14.0 50 25 2.0

C

B2

fx45°

H2

Ød1

H1

AB1

Ød2

CylinDer mountinGS

P1D SerieS - PiVot BraCket for mt4

Intended for use together with central trunnion MT4.

Material Pivot bracket: Surface-treated aluminium Bearing acc. to DIN 1850 C: Sintered oil-bronze bushing

Supplied in pairs.


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1D Series Center trunnion mt4 for P1D-t

CylinDer mountinGS

P1D SerieS - Center trunnion mt4 for P1D-t

According to ISO MT4, VDMA 24 562, AFNOR

Bore(mm)

TMh14

(mm)

TLh14

(mm)

TDe9

(mm)R

(mm)UW

(mm)L1

(mm)X1

(mm)

XVmin

(mm)X2

(mm)

32 50 12 12 1.0 46 15 73.0 62.0 84.0

40 63 16 16 1.6 59 20 82.5 73.0 92.0

50 75 16 16 1.6 69 20 90.0 80.5 99.5

63 90 20 20 1.6 84 25 97.5 89.5 106.0

80 110 20 20 1.6 102 25 110.0 98.0 122.0

100 132 25 25 2.0 125 30 120.0 110.5 129.5

125 160 25 25 2.0 155 32 145.0 132.0 158.0

160 200 32 32 2.5 190 70 C.F. 169 C.F.

200 250 32 32 2.5 242 70 C.F. 184 C.F.

XVstd = X1 + Stroke length/2 XVmax = X2 + Stroke length C.F. = Consult Factory

TL

UW

TM

TD

TL

R

XVstd

L1LL

XVmin

XVmax

Tie Rod Version

Standard*

TL

UW

TMT

DTL

R

XVstd

L1LL

XVmin

XVmax

TL

UW

TM

TD

TL

R

XVstd

L1LL

XVmin

XVmax

TL

UW

TM

TD

TL

R

XVstd

L1LL

XVmin

XVmax

Intended for articulated mounting of cylinder. This mounting is only available for the tie-rod design of P1D. The trunnion is factory-fitted in the center of the cylinder or at an optional location. Order by specifying Mounting Style G or 7 and providing the desired XV dimension (3-digit measure in mm). Combined with pivot bracket for MT4 for 32-125mm bores.

Material: Trunnion: Zinc plated steel (Cast iron for 160-200mm bores)

Trunnion with optional locationOrdered by letter G in position 17 and desired XV-measure (3-digit measure in mm) must be supplied.


Catalog PH00�/NA

Cylinders

6

According to ISO MT4, VDMA 24 562, AFNOR

Part No.Bore(mm)

TMh14

(mm)

TLh14

(mm)

TDe9

(mm)R

(mm)UW

(mm)L1

(mm)XV1

(mm)X

(mm)

P1D-4KMYF 32 50 12 12 1.0 46 14 19.0 127.0

P1D-4LMYF 40 63 16 16 1.6 59 19 20.5 144.5

P1D-4MMYF 50 75 16 16 1.6 69 19 27.5 152.5

P1D-4NMYF 63 90 20 20 1.6 84 24 25.0 170.0

P1D-4PMYF 80 110 20 20 1.6 102 24 34.0 186.0

P1D-4QMYF 100 132 25 25 2.0 155 29 36.5 203.5

XV2 = X + Stroke length

TL

UW

TM

TD

TL

R

XV1

L1LL

XV2

L1LL

Pneumatic Cylinder MountingsP1D Series flange mounted trunnion

CylinDer mountinGS

P1D SerieS - flanGe mounteD trunnion

TL

UW

TM

TD

TL

R

XV1

L1LL

XV2

L1LL

Intended for articulated mounting of cylinder. This trunnion can be flange mounted on the front or rear end cover of all P1D cylinders. If you choose, you can order a complete cylinder with factory-fitted flange mounted trunnion. Individual trunnions have part numbers as shown below.

Material Trunnion: zinc plated steel Screws: zinc plated steel, 8.8

Delivered complete with mounting screws for attachment to the cylinder


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1D Series Swivel rod eye - Clevis

PiSton roD mountinGS

P1D SerieS - SwiVel roD eye

According to ISO 8�3�

Part No.Stainless Steel

Part No.Bore(mm)

A(mm)

Bmin

(mm)

Bmax(mm)

CE(mm)

CNH9

(mm)

ENh12

(mm)ER

(mm) KK

LEmin

(mm)N

(mm)O

(mm) Z

P1C-4KRS P1S-4JRT 32 20 48.0 55 43 10 14 14 M10x1.25 15 17 10.5 12°

P1C-4LRS P1S-4LRT 40 22 56.0 62 50 12 16 16 M12x1.25 17 19 12.0 12°

P1C-4MRS P1S-4MRT 50 28 72.0 80 64 16 21 21 M16x1.5 22 22 15.0 15°

63 28 72.0 80 64 16 21 21 M16x1.5 22 22 15.0 15°

P1C-4PRS P1S-4PRT 80 33 87.0 97 77 20 25 25 M20x1.5 26 32 18.0 15°

100 33 87.0 97 77 20 25 25 M20x1.5 26 32 18.0 15°

P1C-4RRS P1S-4RRT 125 51 123.5 137 110 30 37 35 M27x2 36 41 25.0 15°

L075470036 C.F. 160/200 56 C.F. C.F. 125 35* 43 40 M36x2 40 50 28.0 15°

*H7 C.F. = Consult Factory

CN

B

N

Z

ACE

LE

O

KK

EN

ER

Z

Swivel rod eye for articulated mounting of cylinder. Swivel rod eye can be combined with clevis bracket GA. Maintenance-free.

Materials Swivel rod eye: Zinc-plated steel Swivel bearing according to DIN 648K: Hardened steel

Materials Swivel rod eye: Stainless steel Swivel bearing according to DIN 648K: Stainless steelUse stainless steel nut with stainless steel swivel rod eye.

CN

B

N

Z

ACE

LE

O

KK

EN

ER

Z

According to ISO 8�40

Part No.Stainless Steel

Part No.Bore(mm)

A(mm)

Bmin

(mm)

Bmax(mm)

CE(mm)

CKh11/E9(mm)

CL(mm)

CM(mm)

ER(mm) KK

LE(mm)

O(mm)

P1C-4KRC P1S-4JRD 32 20 45.0 52 40 10 20 10 16 M10x1.25 20 28.0

P1C-4LRC P1S-4LRD 40 24 54.0 60 48 12 24 12 19 M12x1.25 24 32.0

P1C-4MRC P1S-4MRD 50 32 72.0 80 64 16 32 16 25 M16x1.5 32 41.5

63 32 72.0 80 64 16 32 16 25 M16x1.5 32 41.5

P1C-4PRC P1S-4PRD 80 40 90.0 100 80 20 40 20 32 M20x1.5 40 50.0

100 40 90.0 100 80 20 40 20 32 M20x1.5 40 50.0

P1C-4RRC P1S-4RRD 125 56 123.5 137 110 30 55 30 45 M27x2 54 72.0

L075490036 C.F. 160/200 71 C.F. C.F. 144 35 70 35 57 M36x2 72 95

C.F. = Consult Factory

CK

B

ER

CELEA

CL

CM O

KK


P1D SerieS - CleViS

CK

B

ER

CELEA

CL

CM O

KK

Clevis for articulated mounting of cylinder.

Material Clevis, clip: Galvanized steel Pin: Hardened steel

Material Clevis: Stainless steel Pin: Stainless steel Circlips according to DIN 471: Stainless steel


Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1D Series flexo Coupling - nuts


P1D SerieS - flexo CouPlinG

Part No.Bore(mm)

Bmin

(mm)

Bmax(mm) DL

EH(mm)

EI(mm)

EK(mm)

EL (mm)

EN(mm)

EO(mm)

EP(mm)

EQ(mm)

ER(mm)

M(mm) Z

P1C-4KRF 32 36.0 43 M10x1.25 20 23 70 31 12 30 30 19 30 5.0 4°

P1C-4LRF 40 37.0 43 M12x1.25 23 23 67 31 12 30 30 19 30 6.0 4°

P1C-4MRF50 53.0 61 M16x1.5 40 32 112 45 19 41 41 30 41 8.0 4°

63 53.0 61 M16x1.5 40 32 112 45 19 41 41 30 41 8.0 4°

P1C-4PRF80 57.0 67 M20x1.5 39 42 122 56 19 41 41 30 41 10.0 4°

100 57.0 67 M20x1.5 39 42 122 56 19 41 41 30 41 10.0 4°

P1C-4RRF 125 75.5 89 M27x2 48 48 145 60 24 55 55 32 55 13.5 4°

L075530036 160/200 C.F. C.F. M36x2 72 78 251 C.F. 36 75 75 50 55 18.0 4°


DL

ER

Z

M

Z

DL

EN EO EP EQ

EI

EL

B

EK

EH

M

Flexo coupling for articulated mounting of piston rod. Flexo fitting is intended to take up axial angle errors within a range of ±4°.

Material Flexo coupling, nut: Zinc-plated steel Socket: Hardened steel

Supplied complete with galvanized adjustment nut.

According to DIN 43� B

SteelPart No.

Stainless SteelPart No.

Acid-ProofPart No.

Bore(mm)

A(mm)

B(mm) C

9128985601 9126725404 0261109919 32 17 5.0 M10x1.25

0261109910 9126725405 0261109920 40 19 6.0 M12x1.25

9128985603 9126725406 0261109917 50 24 8.0 M16x1.5

63 24 8.0 M16x1.5

0261109911 0261109921 0261109916 80 30 10.0 M20x1.5

100 30 10.0 M20x1.5

0261109912 0261109922 0261109918 125 41 13.5 M27x2

L075540036 C.F. C.F. 160/200 55 18.0 M36x2


A

C B


P1D SerieS - nutS

Intended for fixed mounting of accessories to the piston rod.

Material: Zinc-plated steelAll P1D cylinders are delivered with a zinc-plated steel piston rod nut, except P1D Clean, which is delivered with a stainless steel piston rod nut instead.

Material: Stainless steel A2All P1D cylinders are delivered with a zinc-plated steel piston rod nut, except P1D Clean, which is delivered with a stainless steel piston rod nut instead.

Material: Acid-proof steel A4Cylinders with acid-proof piston rod are supplied with nut of acid-proof steel


Catalog PH00�/NA

CylindersPneumatic Cylinder AccessoriesP1D Series Screw Sets

aCCeSSorieS

P1D SerieS - SCrew Set for mP2, mP4, mS1 anD Ga

Part No.Bore (mm)

9301054321 32

9301054321 40

9301054322 50

9301054322 63

9301054323 80

9301054323 100

9301054324 125

Part No.Bore(mm)

9301054331 32

9301054331 40

9301054332 50

9301054332 63

9301054333 80

9301054333 100

9301054334 125

Set of stainless steel screws for fitting clevis brackets MP2, MP4 and GA onto the cylinder. The screws have an internal hexagonal head and are used in special environments, e.g. the food industry, or where there are extra demands for protection against corrosion.

Material: According to DIN 912, Stainless steel, A2

4 pcs per pack.

Set of stainless steel screws for fitting flanges MF1/MF2 onto the cylinder. The screws have an internal hexagonal head and are used in special environments, e.g. the food industry, or where there are extra demands for protection against corrosion.

Material: According to DIN 6912, Stainless steel, A2

4 pcs per pack

aCCeSSorieS

P1D SerieS - SCrew Set for mf1/mf2


Catalog PH00�/NA

Cylinders

6

Part No.Bore(mm)

9121742201 32

9121742201 40

9121742202 50

9121742202 63

9121742203 80

9121742203 100

9121742204 125

Bore CD CL Part No.

160/200 30 170.50 L075500160

Bore EK d4 L1 L2 L3 L4 Part No.

160/200 35 6 119 7 131 41 L075520160

For Clevis Bracket MP2 For Rear Swivel Eye MP6

Set of sealing plugs to be fitted in unused end covers. The plugs can be used for all P1D cylinders to avoid collecting dirt and fluids in the end cover screw recesses.

Material: Polyamid PA

4 pcs per pack

Pneumatic Cylinder AccessoriesP1D Series Sealing Plugs – Pivot Pin Sets

aCCeSSorieS

P1D SerieS - SealinG PluGS

aCCeSSorieS

P1D SerieS - PiVot Pin SetS for 160-200mm Bore CylinDer aCCeSSorieS


Catalog PH00�/NA

CylindersPneumatic CylindersP1a Series

mini iSo PneumatiC CylinDerS

P1a SerieS - How to orDer

General Description: The Parker P�A series of pneumatic cylinders are intended for use in a wide range of applications. These cylinders are particularly suitable for lighter duties in the packaging, food and textile industries. Hygienic design, the use of corrosion-resistant materials and initial lubrication with our food-grade grease makes the cylinders suitable for food industry applications.

Proven design and high quality manufacturing throughout ensure long service life and optimum performance.

Mounting dimensions are in accordance with ISO 6432 and CETOP RP52P. This greatly simplifies installation and world-wide interchangeability.

The Mini ISO range is available with bumpers or adjustable pneumatic cushioning. Controlled by simple bleed screws for fine adjustment, the adjustable cushioned cylinders can be operated with higher mass loads and at higher speeds than those with fixed end cushioning bumpers.

The Mini ISO range is also available in an all-stainless version with piston rod, cylinder body and end covers of stainless steel for use in extremely severe environments. Consult the Actuator Division for more information.

A complete range of sensors for proximity sensing is available as accessories: both reed and solid state sensors are available. Either can be supplied with flying leads or cable and multi-pin connector.

Stroke Length (mm)

E.g. 0025 = 25 mm

P1a – S 016 m S – 0025

Cylinder Type / Function

MDouble-acting, adjustable cushioning. Ø16-25 mm. Not for sealing material type F and L

D Double-acting, bumpers, Ø10 - Ø25

FDouble-acting, adjustable cushioning, double rod, Ø16-25 mm. Not forsealing material type F and L.

K Double-acting, bumpers, double rod, Ø10 - Ø25

H

Double-acting, adjustable cushioning, double rod (hollow), Ø20-25 mm,max. stroke 125 mm. Not for sealingmaterial type F and L.

PDouble-acting, bumpers, double rod(hollow), Ø20-25 mm, max. stroke125 mm

S Single-acting, bumpers, spring returnfor retract stroke, Ø10-25 mm

T Single-acting, bumpers, spring return for advance stroke, Ø16-25 mm

Sealing Material

SStandard -4°F to +176°FMagnetic piston

F

High temperature:Ø10, 12 and 16 mm14°F to 248°FØ20 and 25 mm14°F to 302°FNon magnetic piston

LLow temperature-40°F to +140°FNon magnetic piston

N

No PTFE or copperStandard seals -4°F to +140°F Magnetic piston

V

External seals of fluorinated rubber-4°F to +176°FMagnetic piston

Cylinder Bore

010 10mm

012 12mm

016 16mm

020 20mm

025 25mm


Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1a Series


P1a SerieS - Stroke lenGtHS

Cylinder Model Bore Size

Stroke Length (+ = standard, – = non-standard, blank = N/A)

10 15 20 25* 30 40 50* 80* 100* 125* 160* 200* 250* 320* 400* 500*

Double Acting with fixed end-cushioning:

P1A-S 010 D 10 + + + + + + + + + + – – – – – –P1A-S 012 D 12 + + + + + + + + + + + + – – – –P1A-S 016 D 16 + + + + + + + + + + + + – – – –P1A-S 020 D 20 + + + + + + + + + + + + + + – –P1A-S 025 D 25 + + + + + + + + + + + + + + – –

Double Acting with adjustable end-cushioning:

P1A-S 016 M 16 + + + + + + + + + + + + + +P1A-S 020 M 20 + + + + + + + + + + + + + +P1A-S 025 M 25 + + + + + + + + + + + + + +

Single Acting:

P1A-S 010 SS 10 + + – + – + + +P1A-S 012 SS 12 + + – + – + + +

P1A-S 016 SS(TS) 16 + + – + – + + +**

P1A-S 020 SS(TS) 20 + + – + – + + +P1A-S 025 SS(TS) 25 + + – + – + + +

*Standard stroke lengths in mm according to ISO 4393 ** Not for the TS version

Note: For sensor specifications and part numbers, please refer to the Electronic Sensors section.

Working Pressure max �45 PSI

Working Temperature max �76°F min 4°F

High-Temperature Version max Ø20 and 25 mm - 302°F Ø�0, �2 and �6 mm - 248°F min �4°F

Low-Temperature Version max �40°F min -40°F

Prelubricated, further lubrication is not normally necessary.If additional lubrication is introduced it must be continued.


P1a SerieS - StanDarD SPeCifiCationS


Catalog PH00�/NA



P1a SerieS - material SPeCifiCation

Piston rod: Stainless steel, DIN X �0 CrNiS �8 �Piston rod seal: Fluorocarbon rubber FPMPiston rod bearing: Multilayer PTFE/steelend covers: Anodized aluminiumo-ring, internal: Nitrile rubber, NBRCylinder barrel: Stainless steel, DIN X 5 CrNi �8 �0Piston, complete: Nitrile rubber, NBR/steelmagnet holder: Thermoplastic elastomermagnet: Plastic-coated magnetic materialreturn spring: Surface-treated steelCushioning screw: Stainless steel, DIN X �0 CrNiS �8 �

Model #

Cylinder Piston Rod

Thread

Total Weight at 0mm Stroke

(lbs)

Additional Weight per

10mm Stroke(lbs) Air Consumption Port Size

Bore(mm)

Area(cm2)

Dia.(mm)

Area(cm2)

Double Acting, cushioned stroke

P1A-S 010 D 10 0.78 4 0.13 M4 0.09 0.007 0.0004 1) M5

P1A-S 012 D 12 1.13 6 0.28 M6 0.15 0.009 0.0005 1) M5

P1A-S 016 D 16 2.01 6 0.28 M6 0.20 0.012 0.0009 1) M5

P1A-S 020 D 20 3.14 8 0.50 M8 0.40 0.015 0.0010 1) G1/8

P1A-S 025 D 25 4.91 10 0.78 M10x1.25 0.89 0.025 0.0023 1) G1/8

Double Acting, adjustable cushioning

P1A-S 016 M 16 2.01 6 0.28 M6 0.20 0.012 0.0009 1) M5

P1A-S 020 M 20 3.14 8 0.50 M8 0.40 0.015 0.0010 1) G1/8

P1A-S 025 M 25 4.91 10 0.78 M10x1.25 0.89 0.025 0.0023 1) G1/8

Single Acting

P1A-S 010 SS 10 0.78 4 0.13 M4 0.09 0.007 0.0002 1) M5

P1A-S 012 SS 12 1.13 6 0.28 M6 0.18 0.009 0.0003 1) M5

P1A-S 016 SS(TS) 16 2.01 6 0.28 M6 0.22 0.012 0.0005 1) M5

P1A-S 020 SS(TS) 20 3.14 8 0.50 M8 0.40 0.015 0.0008 1) G1/8

P1A-S 025 SS(TS) 25 4.91 10 0.78 M10x1.25 0.58 0.025 0.0013 1) G1/8

�) Free air consumption per �0 mm stroke length for a double stroke at 87 PSI

Variants mini iSo:low-temperature version, type l:

Piston rod seal: Nitrile rubber, NBRPiston complete: Nitrile rubber, NBR/steel

High-temperature version, type f:

Piston rod seal: Fluorocarbon rubber, FPMPiston complete, Ø10-Ø16: HNBR/steelPiston complete, Ø20-Ø25: FPM/steel

Ptfe and copper free cylinders, type n:

Piston rod bearing: PA plastic

Cylinders with outer sealings in fluorocarbon, type V:

Piston rod seal/ Scraper ring: Fluorocarbon rubber, FPM

note: Spare part = new cylinder

Cylinders are supplied complete with nose mounting and piston rod nuts.

Cylinders with double piston rods are supplied with two piston rod nuts


P1a SerieS - QuiCk referenCe


Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1a Series


P1a SerieS - CylinDer forCeS

Double acting

Model No.Bore Size

(mm)

Theoretical Piston Force (lbs)at 87 PSI

Extension Retraction

P1A-S 010 D 10 10.57 8.76

P1A-S 012 D 12 15.07 11.25

P1A-S 016 D 16 26.98 23.15

P1A-S 020 D 20 42.27 35.52

P1A-S 025 D 25 66.10 55.53

P1A-S 016 M 16 26.98 23.16

P1A-S 020 M 20 42.27 35.52

P1A-S 025 M 25 66.10 55.53

Indicated cylinder forces are theoretical and should be reduced according to the working conditions.

Double acting Double acting, Double rod


Catalog PH00�/NA



P1a SerieS - CylinDer forCeS

Model No. Stroke

Theoretical Piston Force (lbs) at 87 PSISpring Retraction Spring Extension

(lbs max) (lbs. min) (lbs. max) (lbs. min)

P1A-S 010 SS

10 8.5 8.1 2.4 2.0

12 8.5 8.1 2.4 2.0

25 8.7 8.1 2.4 2.0

40 8.5 7.6 2.9 2.0

50 8.7 7.6 2.9 1.7

80 8.7 7.6 2.9 1.7

P1A-S 012 SS

10 11.9 11.4 3.6 3.1

15 11.9 11.4 3.6 3.1

25 12.3 11.4 3.6 2.7

40 11.9 10.8 4.2 3.3

50 11.9 10.8 4.2 3.1

80 12.3 10.8 4.2 2.7

P1A-S 016 SS(TS)

10 22.0 (19.1) 22.2 (18.8) 4.7 (4.2) 4.0 (4.0)

15 23.1 (19.3) 22.2 (18.8) 4.7 (4.2) 3.8 (3.8)

25 23.8 (19.8) 22.2 (18.8) 4.7 (4.2) 3.3 (3.3)

40 23.8 (20.3) 21.3 (18.8) 5.6 (4.2) 3.1 (3.1)

50 24.2 (20.4) 21.3 (18.8) 5.6 (4.2) 2.7 (2.7)

80 24.0 (21.3) 21.3 (18.8) 5.6 (4.2) 2.9 (2.9)

P1A-S 020 SS(TS)

10 36.6 (29.6) 36.1 (29.2) 6.1 (6.3) 5.6 (5.8)

15 36.8 (29.8) 36.1 (29.2) 6.1 (6.3) 5.4 (5.6)

25 37.5 (30.3) 36.1 (29.2) 6.1 (6.3) 4.7 (5.1)

40 37.3 (31.0) 35.7 (29.2) 6.5 (6.3) 4.9 (4.9)

50 37.7 (31.4) 35.7 (29.2) 6.5 (6.3) 4.5 (4.5)

80 38.2 (31.2) 36.1 (24.2) 6.1 (11.2) 4.0 (4.2)

P1A-S 025 SS(TS)

10 57.5 (46.1) 56.9 (45.6) 9.2 (9.9) 8.5 (9.4)

15 58.0 (46.5) 56.9 (45.6) 9.2 (9.9) 8.1 (9.0)

25 58.9 (47.2) 56.9 (45.6) 9.2 (9.9) 7.2 (8.3)

40 58.7 (48.1) 56.2 (45.6) 9.9 (9.9) 7.4 (7.4)

50 59.4 (48.8) 56.2 (45.6) 9.9 (9.9) 6.7 (6.7)

80 59.4 (50.1) 56.4 (46.3) 9.6 (9.2) 6.7 (5.4)

Single acting

Single-acting, Spring return Single-acting, Spring extend


Catalog PH00�/NA

Cylinders

6

Pneumatic CylindersP1a Series Double acting – Single acting type SS, type tS

PneumatiC CylinDerS

P1a SerieS - DimenSionS

AM

ZJ

XC

L

BF

ØB

E

ØC

D

AF

WHPSW

ØK

K

ØB

E

EW

C

H

EEAF

ØK

K

ØB

E

Cylinder Bore(mm)

AM 0/-2(mm) BE

AF(mm)

BF(mm)

C(mm)

CD h9(mm) EE

EW(mm)

H(mm) KK

L(mm)

SW(mm)

WH±1.2 (mm)

10 12 M12x1.25 12 10 14.0 4 M5 8 16.7 M4 6 – 16

12 16 M16x1.5 18 13 18.0 6 M5 12 19.1 M6 9 5 22

161) 16 M16x1.5 18 13 18.0 6 M5 12 19.1 M6 9 5 22

162) 16 M16x1.5 18 13 25.0 6 M5 12 24.0 M6 9 5 22

20 20 M22x1.5 20 14 24.0 8 G1/8 16 27.0 M8 12 7 24

25 22 M22x1.5 22 14 27.5 8 G1/8 16 29.0 M10x1.25 12 9 28

1) P1A-S016DS/SS/TS 2) P1A-S016MS

Double acting cylinders

Cylinder Bore(mm)

XC(mm)

ZJ(mm)

P(mm)

10 64 + stroke 84 + stroke 46 + stroke





Single-acting, spring return, type SS

Cylinder Bore(mm)

XC (mm) at Various Strokes ZJ (mm) at Various Strokes P (mm) at Various Strokes

10 15 25 40 50 80 10 15 25 40 50 80 10 15 25 40 50 80

10 74 79 89 126 136 174 94 99 109 146 156 194 56 61 71 108 118 156

12 85 90 100 132 142 185 109 114 124 156 166 209 58 63 73 105 115 158

16 92 97 107 122 132 184 114 119 129 144 154 206 63 68 78 93 103 155

20 105 110 120 135 145 191 135 140 150 165 175 221 77 82 92 107 117 163

25 114 119 129 144 154 201 142 147 157 172 182 229 78 83 93 108 118 165

Single-acting, spring-extended, type tS

Cylinder Bore(mm)

ZC 3) (mm) at Various Strokes ZJ 3) (mm) at Various Strokes P (mm) at Various Strokes

10 15 25 40 50 80 10 15 25 40 50 80 10 15 25 40 50 80

16 107 112 122 137 147 – 134 139 149 164 174 – 78 83 93 108 118 –

20 120 125 135 150 160 195 156 161 171 186 196 231 92 97 107 122 132 167

25 129 134 144 159 169 205 165 170 180 195 205 241 93 98 108 123 133 169

3) With piston rod retracted, as shown in the dimension drawingLength tolerances ±1 mm Stroke length tolerance +1.5/0 mm

Double acting cylinders Double piston rod

Single acting

AM

ZJ

XC

L

BF

ØB

E

ØC

D

AF

WHPSW

ØK

K

ØB

E

EW

C

H

EEAF

ØK

K

ØB

E

WH + stroke

AM

ZJ

XC

L

BF

ØB

E

ØC

D

AF

WHPSW

ØK

K

ØB

E

EW

C

H

EEAF

ØK

K

ØB

E


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1a Series flange mf8 – foot mS3

CylinDer mountinGS

P1a SerieS - flanGe mf8

D

C

G

E B

A

I

F

H

E F

A

DB

C

Intended for fixed attachment of the cylinder. The flange is designed for mounting on the front or rear end-covers.

Material: Surface-treated steel

This mounting is also available in stainless steel. Consult the Actuator Division for additional information.

Part No.CylinderØ (mm) A B C D E F

P1A-4CMB 10 4.5 30 40 22 3 13

P1A-4DMB 12-16 5.5 40 52 30 4 18

P1A-4HMB20 6.6 50 66 40 5 19

25 6.6 50 66 40 5 23

Intended for fixed attachment of the cylinder. The bracket is designed for mounting on the front or rear end-covers.

Material: Surface-treated steel

This mounting is also available in stainless steel. Consult the Actuator Division for additional information.

Part No.Cylinder Ø

(mm)A

(mm)B

(mm)C

(mm)D

(mm)E

(mm)F

(mm)G

(mm)H

(mm)I

(mm)

P1A-4CMF 10 4.5 16 25 35 3 24 26.0 16 11

P1A-4DMF 12-16 5.5 20 32 42 4 32 32.5 20 14

P1A-4HMF20 6.5 25 40 54 5 36 45.0 25 17

25 6.5 25 40 54 5 40 45.0 25 17

E F

A

D

B

C

CylinDer mountinGS

P1a SerieS - foot mf3

D

C

G

E B

A

I

F

H


Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1a Series Cover trunnion – mounting nut

CylinDer mountinGS

P1a SerieS - CoVer trunnion

ØA

D E ØF

BC

G H

A

B

C

Intended for articulated mounting of the cylinder. The flange is designed for mounting on the front or rear end-covers.

Material: Stainless steel, DIN X 10 CrNiS 18 9

Part No.Cylinder Ø

(mm)A

(mm)B h14(mm)

C(mm)

D(mm)

E e9(mm)

F(mm)

G(mm)

H(mm)

P1A-4CMJ 10 12.5 26 38 20 8 4 6 10

P1A-4DMJ 12-16 16.5 38 58 25 10 6 8 14

P1A-4HMJ20 22.5 46 66 30 10 6 8 16

25 22.5 46 66 30 10 6 8 20

Intended for fixed mounting of the cylinder. Cylinders are supplied complete with one mounting nut.

Material: Galvanized steel

This nut is also available in stainless steel.

Part No.Cylinder Ø

(mm)A

(mm)B

(mm)C

(mm)

9127385101 10 16 3 M12x1.25

9127385102 12-16 20 4 M16x1.50

9127385103 20-25 27 5 M22x1.50

ØA

D E ØF

BC

G H

CylinDer mountinGS

P1a SerieS - mountinG nut


Catalog PH00�/NA

CylindersPneumatic Cylinder MountingsP1a Series Clevis Bracket - Clevis

CylinDer mountinGS

P1a SerieS - CleViS BraCket

CylinDer mountinGS

P1a SerieS - CleViS

I±J

D

C G

E F

A

H DB

Intended for articulated mounting of the cylinder. Supplied with shaft for mounting on the rear end cover.

Material: Bracket: surface-treated steel, black Pin: surface hardened steel Circlips: according to DIN 471: Stainless steel

This mounting is also available in stainless steel.

Part No.Cylinder Ø

(mm)A

(mm)B

(mm)C

(mm)D

(mm)E

(mm)F

(mm)G

(mm)H

(mm)I

(°)J

(°)

P1A-4CMT 10 4.5 13 8 24 12.5 20 65.3 5 160 17

P1A-4DMT12 5.5 18 12 27 15.0 25 73.0 7 170 15

16 5.5 18 12 27 15.0 25 80.0 7 170 15

P1A-4HMT20 6.5 24 16 30 20.0 32 91.0 10 165 10

25 6.5 24 16 30 20.0 32 100.0 10 165 10

According to ISO 8140. Intended for articulated mounting of the cylinder. This mounting is adjustable in the axial direction. Supplied complete with pin.

Material: Galvanized steel This mounting is also available in stainless steel.

Part No.Cylinder Ø

(mm)A

(mm) BC

(mm)D

(mm)E

(mm)F

(mm)G

(mm)H

(mm)I

(mm)J

(mm)

P1A-4CRC 10 4 M4 2.2 8 8 5 16 4 22.0 2.0

P1A-4DRC 12-16 6 M6 3.2 12 12 7 24 6 31.0 3.0

P1A-4HRC 20 8 M8 4.0 16 16 10 32 8 40.5 3.5

P1A-4JRC 25 10 M10x1.25 5.0 20 20 12 40 10 49.0 3.0

A

C

B

H

D

EF

J

G + Stroke

I

A

C

B

H

D

EF

J

G + Stroke

I

I±J

D

C G

E F

A

H DB


Catalog PH00�/NA

Cylinders

6

Pneumatic Cylinder MountingsP1a Series Swivel rod eye - rod nut

CylinDer mountinGS

P1a SerieS - SwiVel roD eye

CylinDer mountinGS

P1a SerieS - roD nut

A

J±LC G

I E F

B H D

E

F

D

According to ISO 8139. Intended for articulated mounting of the cylinder. This mounting is adjustable in the axial direction.

Material: Swivel rod eye: Galvanized steel Ball: hardened steel This mounting is also available in stainless steel.

Part No.Cylinder Ø

(mm)A

(mm) BC

(mm)D

(mm)E

(mm)F

(mm)G

(mm)H

(mm)I

(mm)J

(mm)K

(mm)L

(mm)

P1A-4CRS 10 5 M4 2.2 8 10 9 27 6.0 8 33.0 9 2.0

P1A-4DRS 12-16 6 M6 3.2 9 10 10 30 6.8 9 38.5 11 1.5

P1A-4HRS 20 8 M8 4.0 12 12 12 36 9.0 12 46.0 14 2.0

P1A-4JRS 25 10 M10x1.25 5.0 14 14 14 43 10.5 15 52.5 17 2.5

Intended for fixed mounting on the piston rod. Cylinders are supplied complete with one rod nut. (cylinders with double piston rod are supplied with two rod nuts.)

Material: Galvanized steel This nut is also available in stainless steel.

Part No.Cylinder Ø

(mm)D

(mm)F

(mm)E

(mm)

0261110600 10 M4 7 2.2

0261210800 12-16 M6 10 3.2

0261211000 20 M8 13 4.0

9128985601 25 M10x1.25 17 5.0

A

J±LC G

I E F

B H D


Catalog PH00�/NA

Cylinders

notes

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________


Catalog PH00�/NA

Cylinders

6

Industrial CylindersSeries 2a - 3l

Bore* Specify in inches –

Cushion- Used only if cushion required C Head

mounting* Head Tie Rods Extended TB Style Cap Tie Rods Extended TC Both End Tie Rods Extended TD Head Rectangular Flange J Cap Rectangular Flange H Head Square Flange JB Side Lugs C† Side Tapped F† Head Trunnion D Cap Fixed Clevis BB

Series* Used in all 2A/3L Model Numbers –2A –3L

Piston Lipseal® Piston (This code used for 3L Series

L

only. Leave this space blank for 2A Series.)

Ports* SAE Straight Thread O-Ring Port T NPTF (Dry Seal Pipe Thread) U

Common Fluorocarbon Seals V

modifications (See Operating Fluids/Seals page.)

Special Used only if special modifications modifications are required: Oversize Ports Port Position Change Rod End Bellows S Special Seals Stop Tube Stroke Adjuster Tie Rod Supports

Piston rod* For Single Rod Cylinders, � number select one only. (See Piston Rod - 2 Stroke Selection Chart - for 3 minimum piston rod diameter.) 7

Piston* Select: rod end Style 4 Small Male 4 Style 8 Intermediate Male 8 Style � Short Female � Style 3 Special (specify) 3

Piston rod* UNF Standard A threads

Cushion-Cap Used only if cushion required C

Stroke* Specify in inches –

Series 2a/3l model numbers – How to Develop them – How to “Decode” them

Parker Series 2A/3L cylinders can be completely and accurately described by a model number consisting of coded symbols. To develop a model number, select only those symbols that

represent the cylinder required, and place them in the sequence indicated below.

feature Description Symbol

Use Symbol S to designate any specialmodification except piston rod end.

* Required for Basic Cylinder Model Number† Cylinders with these mounting styles should have a minimum stroke length equal to or greater than their bore size.

4” t V S 1 4 C 12”l–3lC f a

Styles 4, 8 and � are catalog standards.Specify Style 3 for any special piston rod end.

Dark arrows indicate Basic Minimum Model Number.

Cylinder serial numbers are factory production record numbers and are assigned to each cylinder, in addition to the model number.

inDuStrial CylinDerS

How to orDer


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2a - 3l - 2H

HyDrauliC anD PneumatiC inDuStrial CylinDerS

CylinDer PreSSure ratinGS

application DataThe proper application of a fluid power cylinder requires consideration of the operating pressure, the fluid medium, the mounting style, the length of stroke, the type of piston rod connection to the load, thrust or tension loading on the rod,

mounting attitude, the speed of stroke, and how the load in motion will be stopped. Information given here provides pressure rating data for pneumatic and hydraulic cylinders.

Pneumatic CylindersStandard operating fluid — filtered air which is free of moisture. 2A and 2AN series cylinders are recommended for maximum 250 psi heavy duty service.

Hydraulic Cylinders (Heavy duty)Standard operating fluid - clean, filtered hydraulic oil. Pressure ratings for heavy duty hydraulic cylinders are shown in the following table:

Pressure ratingsSeries 2H hydraulic cylinders are recommended for pressures to 3000 PSI for heavy-duty service with hydraulic oil. The 4:� design factor ratings shown are based on tensile strength of material and are for code � rod dia. only. The rating is conservative for continuous severe applications. Design factors at other pressures can be calculated from this rating. In addition, mounting styles, stroke, etc., should be considered because of the limiting effect they may have on these ratings.

Hydraulic Cylinders (medium duty)Pressure ratings for “Series 3L” hydraulic cylinders vary by bore size and rod size as shown in table below. For pressures higher than those indicated, Series 2H heavy duty cylinders should be used.

Series 3l Hydraulic Cylinders maximum Pressure ratingPressure ratings fluid medium air

maximum Pressure ratings

Bore Size(in.)

RodNumber

RodDiameters

(in.)

Pressure Rating At 4:1 Design* Factor

(On Tensile)

1 1/21 5/8 2000

2 1 2300

1 5/8 1100

2 3 1 2000

2 1 3/8 2000

7 5/8 700

2 1/2 1 1 1400

2 1 3/4 1400

1 1 1300

3 1/4 3 1 3/8 1300

2 2 1300

7 1 900

4 1 1 3/8 900

2 2 1/2 900

Bore Size(in.)

Standard Piston RodDiameters

(in.)

Series 2A, 2AN Max. Heavy-DutyOperating Pressure

(PSI)

1 1/2 250

1 1/2 5/8 250

2 5/8 250

2 1/2 5/8 250

3 1/4 1 250

4 1 250

Bore Size(in.)

RodDiameters

(in.)

4:1* Design Factor(Tensile) (PSI)

Heavy-DutyService

(PSI)

1 1/2 5/8 2530 3000

2 1 2950 3000

2 1/2 1 2340 3000

3 1/4 1 3/8 2250 3000

4 1 3/4 2130 3000*Applies to all mountings except J, H and D. See Series 2H.

*Applies to all mountings except J. See Series 3L


Catalog PH00�/NA

Cylinders

6

Stop tubingStop tube is recommended to lengthen the distance between the gland and piston to reduce bearing loads when the cylinder is fully extended. This is especially true of horizontally mounted and long stroke cylinders. Long stroke cylinders achieve additional stability through the use of a stop tube.

Drawing a

When specifying cylinders with long stroke and stop tube, be sure to call out the net stroke and the length of the stop tube. Machine design can be continued without delay by laying in a cylinder equivalent in length to the NET STROKE PLUS STOP TUBE LENGTH, which is referred to as GROSS STROKE.Refer to piston rod/stroke selection chart to determine stop tube length.

Drawing B

Double piston design is supplied on air cylinders with cushion head end or both ends.

Drawing C

This design is supplied on all non cushion cylinders.

Industrial CylindersSeries 2a - 3l - 2H

Group 1 FIXED MOUNTS which absorb force on cylinder centerline.

Heavy-Duty ServiceFor Thrust Loads Mtg. Style TCFor Tension Loads Mtg. Styles JB, JJ, TB

medium-Duty ServiceFor Thrust Loads Mtg. Styles HFor Tension Loads Mtg. Styles J, JB

light-Duty ServiceFor Thrust Loads Mtg. Style HFor Tension Loads Mtg. Style J

Group 2 PIVOT MOUNTS which absorb force on cylinder centerline.

Heavy-Duty ServiceFor Thrust Loads Mtg. Style For Tension Loads Mtg. Styles BB, D

medium-Duty ServiceFor Thrust Loads Mtg. Style BBFor Tension Loads Mtg. Style BB

light-Duty ServiceFor Thrust Loads ——————— For Tension Loads ———————

Group 3 FIXED MOUNTS which do not absorb force on the centerline.

Heavy-Duty ServiceFor Thrust Loads Mtg. Style CFor Tension Loads Mtg. Style C

medium-Duty ServiceFor Thrust Loads Mtg. Style FFor Tension Loads Mtg. Style F

Series 2a, 3l, 2H Cylindersmounting ClassesStandard mountings for fluid power cylinders fall into three basic groups. The groups can be summarized as follows:

Group � – Straight Line Force Transfer with fixed mounts which absorb force on cylinder centerline.Group 2 – Pivot Force Transfer. Pivot mountings permit a cylinder to change its alignment in one plane.

Group 3 – Straight Line Force Transfer with fixed mounts which do not absorb force on cylinder centerline.

Because a cylinder’s mounting directly affects the maximum pressure at which the cylinder can be used, the chart below should be helpful in selection of the proper mounting combination for your application. Stroke length, piston rod connection to load, extra piston rod length over standard, etc., should be considered for thrust loads. Alloy steel mounting bolts are recommended for all mounting styles, and thrust keys are recommended for Group 3.


StoP tuBinG/mountinG ClaSSeS


Catalog PH00�/NA

Cylinders

Recommended Mounting Styles for Maximum Stroke and Thrust Loads

Rod EndConnection Case

Stroke Factor

Fixed and Rigidly Guided I .50

Pivoted and Rigidly Guided II .70

Supported but not Rigidly

Guided III 2.00

Pivoted and Rigidly Guided IV 1.00

Pivoted and Rigidly Guided VI 2.00


Groups 1 or 3Long stroke cylinders for thrust loads should be mounted using a heavy-duty mounting style at one end, firmly fixed and aligned to take the principal force. Additional mounting should be specified at the opposite end, which should be used for alignment and support. An intermediate support may also be desirable for long stroke cylinders mounted horizontally. Machine mounting pads can be adjustable for support mountings to achieve proper alignment.

Group 2Style D — Trunnion on Head

Style BB — Clevis on Cap

100 2 3 4 5 6 7 8 9 1000 2 3 4 5 6 7 8 9 10,000 2 3 4 5 6 7 8 9 100,000 2 310

20

30

40

50

60

300

200

100908070

THRUST–POUNDS

ROD DIAMETER

BA

SIC

LE

NG

TH

–IN

CH

ES

INC

HE

S O

F

STO

P T

UB

E

1

2

34567

CO

NS

ULT

FA

CTO

RY

58

1

134 2 21

2381

How to use the ChartThe selection of a piston rod for thrust (push) conditions requires the following steps:

�. Determine the type of cylinder mounting style and rod end connection to be used. Then consult the chart below and find the “stroke factor” that corresponds to the conditions used.

2. Using this stroke factor, determine the “basic length” from the equation:

The graph is prepared for standard rod extensions beyond the face of the gland retainers. For rod extensions greater than standard, add the increase to the stroke in arriving at the “basic length.”

3. Find the load imposed for the thrust application by multiplying the full bore area of the cylinder by the system pressure.

4. Enter the graph along the values of “basic length” and “thrust” as found above and note the point of intersection:

A) The correct piston rod size is read from the diagonally curved line labeled “Rod Diameter” next above the point of intersection.

B) The required length of stop tube is read from the right of the graph by following the shaded band in which the point of intersection lies.

C) If required length of stop tube is in the region labeled “consult factory,” submit the following information for an individual analysis:

�) Cylinder mounting style.

2) Rod end connection and method of guiding load.

3) Bore, required stroke, length of rod extension (Dim. “LA”) if greater than standard, and series of cylinder used.

4) Mounting position of cylinder. (Note: If at an angle or vertical, specify direction of piston rod).

5) Operating pressure of cylinder if limited to less than standard pressure for cylinder selected.

warningPiston rods are not normally designed to absorb bending moments or loads which are perpendicular to the axis of piston rod motion. These additional loads can cause the piston rod end to fail. If these types of additional loads are expected to be imposed on the piston rods, their magnitude should be made known to our Engineering Department so they may be properly addressed. Additionally, cylinder users should always make sure that the piston rod is securely attached to the machine member.

Basic = Actual x Stroke Length Stroke Factor

Piston rod — Stroke Selection Chart


CylinDer Stroke CHart


Catalog PH00�/NA

Cylinders

6



oPeratinG fluiDS/SealS/PiStonS/warranty

operating fluids and temperature rangeFluidpower cylinders are designed for use with pressurized air, hydraulic oil.

Standard Seals (class 1)Class � seals are what is normally provided in a cylinder unless otherwise specified. They are intended for use with fluids such as: air, nitrogen, mineral base hydraulic oil or MIL-H-5606 within the temperature range of -�0°F (-23°C) to +�65°F (+74°C). Generally they are nitrile except for piston rod seals in hydraulic cylinders. However the individual seals may be nitrile (Buna-N) enhanced polyurethane, polymyte, P.T.F.E. or filled P.T.F.E.

fluorocarbon Seals (class 5)Class 5 seals are intended for elevated temperature service or for some Phosphate Ester Fluids such as Houghto-Safe �0�0, �055, ��20; Fyrquel �50, 220, 300, 350; Mobile Pyrogard 42, 43, 53, and 55. Note: In addition, class 5 seals can be used with fluids listed below under standard service. However, they are not compatible with Phosphate Ester Fluids such as Skydrols. Class 5 seals can operate with a temperature range of -�0°F (-23°C) to +250°F (+�2�°C). Class 5 seals may be operated to +400°F (+204°C) with limited service life. For temperatures above +250°F (+�20°C) the cylinder must be manufactured with non-studded piston rod and thread and a pinned piston to rod connection. Class 5 Lipseals will have P.T.F.E. back-up washers when required. O-rings will have fluorocarbon back-up when required.

warning The piston rod stud and the piston rod to piston threaded connections are secured with an anaerobic adhesive which is temperature sensitive. Cylinders specified with Class 5 seals are assembled with anaerobic adhesive having a maximum temperature rating of +250°F (+74°C). Cylinders specified with all other seal compounds are assembled with anaerobic adhesive having a maximum operating temperature rating +�65°F (+74°C). These temperature limitations are necessary to prevent the possible loosening of the threaded connections. Cylinders originally manufactured with class � seals (Nitrile) that will be exposed to ambient temperatures above +�65°F (+74°C) must be modified for higher temperature service. Contact the factory immediately and arrange for the piston to rod and the stud to piston rod connections to be properly re-assembled to withstand the higher temperature service.

lipseal PistonsUnder most conditions lipseals provide the best all around service for pneumatic applications. Lipseals with a back-up washer are often used for hydraulic applications when virtually zero static leakage is required. Lipseals will function properly in these applications when used in conjunction with moderate hydraulic pressures. A high load piston option is recommended when operating at high pressures and especially with large bore hydraulic cylinders.

Cast iron Piston ringsCast iron rings are the standard piston seals for 2H and 3L Series cylinders. They offer the widest operating conditions by tolerating high operating pressures, wide temperature range and are compatible with most fluids. The only drawback of cast iron rings is that they allow a small amount of leakage. The leakage for a 4” bore cylinder, operating at 2000 psi, with mineral base hydraulic fluid will be less than �0in3/min. Leakage will increase as pressure, bore size and viscosity of the operating hydraulic fluid increases. For these reasons cast iron rings are not recommended when using water or (H.W.C.F.) fluids.

warrantyParker Hannifin will warrant cylinders modified for water or high water content fluid service to be free of defects in materials or workmanship, but cannot accept responsibility for premature failure due to excessive wear, due to lack of lubricity or where failure is caused by corrosion, electrolysis or mineral deposits within the cylinder.

Pre-lubricated air CylindersParker Hannifin air cylinders are factory pre-lubricated with Lube-A-Cyl applied to seals, piston, cylinder bore, piston rod and gland surfaces, provides for normal cylinder operations with lubricated air.

non-lubricated air CylindersFor heavier duty operation, Series 2AN is recommended for non-lubricated air service. Series 2AN includes an innovative special composite material wick and ring reservoir assembly in each seal groove to retain the extreme pressure lubricant applied at time of assembly. This lubricant coats the cylinder bore and piston rod and mating surfaces.

Note: Fluorocarbon seals are not suitable for use with Skydrol fluid, but can be used with hydraulic oil if desired

Class Number Typical Fluids Temperature Range

1 (Standard) (Nitrile Polyurethane) Air, Nitrogen, Hydraulic Oil, Mil-H-5606 Oil -10OF (-23OC) to +165OF (+74OC)

5 Optional (At extra cost) (Fluorocarbon Seals)

High Temperature Houghto-Safe 1010, 1055, 1120Fyrquel 150, 220, 300, 550

Mobil Pyrogard 42, 43, 53, 55

See above paragraph on Fluorocarbon seals forrecommended temperature range.


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2a - 3l


SerieS 2a HeaVy Duty air CylinDerS/SerieS 3l meDium Duty HyDrauliC CylinDerS

24E R

R

3

E

AA

1

GBB F J

P + STROKELB + STROKEW

EE

Y

K

MM

DD

Styles tB, tC, tD Tie Rods Extended*

24E R

TF

3

UF

1

FB4 HOLES

F

Style J Head Rectangular Flange

2 4R E

FFB4 HOLESTF

3

UF

1

XF

Style H Cap Rectangular Flange

24UF R

R

TF

3

TF

UF

FB8 HOLES

F

Style JB Head Square Flange

* Basic Mounting (T) — NFPA MX0 — no tie rods extended can be supplied upon request.

Style TB (NFPA MX3). Head Tie Rods Extended, illustrated: Style TC (NFPA MX2), Cap Tie Rods Extended; and Style TD (NFPA MX�), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned from Style TB drawing at left.

(NFPA MX3)

(NFPA MF2)

(NFPA MF�)

(NFPA MF5)

Series 3l Pressure limitation for Style ‘J’ mount

* Maximum pressure rating - push application.

Bore Size 1 2 3 7

1 1/2 1400 850 – –

2 1050 450 800 –

2 1/2 700 350 – 700

3 1/4 1300 900 1300 –

4 900 700 – 900

Max. PSI - Push*Rod Code


Catalog PH00�/NA

Cylinders

6

Bore NT R SB ST SU SW+.000/-.001

TD TF TL TN TS UF US UTAdd Stroke

LB P SN SS

1 1/2 1/4-20 1.43 7/16 1/2 15/16 3/8 1.000 2 3/4 1 5/8 2 3/4 3 3/8 3 1/2 4 4 2 1/4 2 1/4 2 7/8

2 5/16-18 1.84 7/16 1/2 15/16 3/8 1.000 3 3/8 1 7/8 3 1/4 4 1/8 4 4 1/2 4 2 1/4 2 1/4 2 7/8

2 1/2 3/8-16 2.19 7/16 1/2 15/16 3/8 1.000 3 7/8 1 1 1/4 3 3/4 4 5/8 4 1/2 5 4 1/8 2 3/8 2 3/8 3

3 1/4 1/2-13 2.76 9/16 3/4 1 1/4 1/2 1.000 4 11/16 1 1 1/2 4 3/4 5 1/2 5 3/4 5 3/4 4 7/8 2 5/8 2 5/8 3 1/4

4 1/2-13 3.32 9/16 3/4 1 1/4 1/2 1.000 5 7/16 1 2 1/16 5 1/2 6 1/4 6 1/2 6 1/2 4 7/8 2 5/8 2 5/8 3 1/4

Bore AA BB CB+.000/-.002

CD CW DD E EE

NPTF† SAE* F FB G J K L LR M MR

1 1/2 2.02 1 3/4 .501 1/2 1/4-28 2 3/8** 6# 3/8 5/16 1 1/2 1 1/4 3/4 3/4 1/2 5/8

2 2.6 1 1/8 3/4 .501 1/2 5/16-24 2 1/2 3/8** 6 3/8 3/8 1 1/2 1 5/16 3/4 3/4 1/2 5/8

2 1/2 3.1 1 1/8 3/4 .501 1/2 5/16-24 3 3/8** 6 3/8 3/8 1 1/2 1 5/16 3/4 3/4 1/2 5/8

3 1/4 3.9 1 3/8 1 1/4 .751 5/8 3/8-24 3 3/4 1/2 10 5/8 7/16 1 3/4 1 1/4 3/8 1 1/4 1 3/4 15/16

4 4.7 1 3/8 1 1/4 .751 5/8 3/8-24 4 1/2 1/2 10 5/8 7/16 1 3/4 1 1/4 3/8 1 1/4 1 3/4 15/16


MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS

table 1 – envelope and mounting Dimensions

** On ��/2”, 2” and 2�/2” bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available.

† Series 3L only: NPTF ports will be furnished as standard unless SAE straight thread ports are specified.

* Series 3L only: SAE straight thread ports are indicated by port number.

# Straight thread ports on ��/2” bore cap end, and head end with Code 2 rod, require an adapter fitting. (See “Straight Thread Port Adapter” drawing on bottom of page.) Adapters are furnished as standard.

MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS

rod end Dimensions — See table 2thread Style 4(NFPA Style SM) Small Male

Straight thread Port adapters

Used on ��/2” bore cap end and on head end of ��/2” bore with Code 2 rod.

Special thread Style 3To order, specify “Style 3” and give desired dimensions for CC or KK, A and LA. If otherwise special, furnish dimensional sketch.

A high strength rod end stud is supplied on thread style 4 through 2” diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured against the rod shoulder. When the workpiece is not shouldered,

style 4 rod ends are recommended through 2” piston rod diameters and style 8 rod ends are recommended on larger diameters. Use style � for applications where female rod end threads are required. If rod end is not specified, style 4 will be supplied.

34

EE

thread Style 8(NFPA Style IM) Intermediate Male

thread Style 9(NFPA Style SF) Short Female

table 2 – rod Dimensions table 3 – envelope and mounting Dimensions

Bore

RodDia.MM

2A RodNo.

3L RodNo.

Style 8

CC

Style 4 & 9

KK A

+.000-.002

B C D LA NA V W Y XG XS XT

Add Stroke

XF

1 1/25/8 1(Std.) 1(Std.) 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 5/8

1 2 2 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5

2

5/8 1(Std.) 1(Std.) 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 5/8

1 3/8 2 2 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 7/8 1 5/16 5/8 1 1/4 2 9/16 2 3/8 2 2 9/16 5 1/4

1 3 3 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5

2 1/2

5/8 1(Std.) 7 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 3/4

1 3/4 2 2 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 3 1/2 1 11/16 3/4 1 1/2 2 13/16 2 5/8 2 1/4 2 13/16 5 5/8

1 3 1(Std.) 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5 1/8

3 1/4

1 1(Std.) 1(Std.) 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 1 7/8 15/16 1/4 3/4 2 7/16 2 1/4 1 7/8 2 7/16 5 5/8

2 2 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 3 5/8 1 15/16 1/2 1 3/8 3 1/16 2 7/8 2 1/2 3 1/16 6 1/4

1 3/8 3 3 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 5/8 1 5/16 3/8 1 2 11/16 2 1/2 2 1/8 2 11/16 5 7/8

4

1 1(Std.) 7 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 1 7/8 15/16 1/4 3/4 2 7/16 2 1/4 1 7/8 2 7/16 5 5/8

2 1/2 2 2 2 1/4-12 1 7/8-12 3 3.124 1 2 1/16 4 5/8 2 3/8 5/8 1 5/8 3 5/16 3 1/8 2 3/4 3 5/16 6 1/2

1 3/8 3 1(Std.) 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 5/8 1 5/16 3/8 1 2 11/16 2 1/2 2 1/8 2 11/16 5 7/8

Thread Rod Extensions and Pilot Dimensions

1 1/2

2

2 1/2

3 1/4

4


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2a - 3l


SerieS 2a HeaVy Duty air CylinDerS/SerieS 3l meDium Duty HyDrauliC CylinDerS

2

R18

4E TD

ETL TL

3

UT

1

XG

Style D Head Trunnion

24E

ST

SWSB4 HOLES

SW

-.005-.010

SWSW

ETS

3

US

1

XS SS + STROKE

SU SUSW SW

E2

Style C Side Lug

24E

E -.0052 -.010

TN

3

1

XT SN + STROKE

F J

P + STROKELB + STROKEW

EE

Y

K

MM

NT THREAD, ND DEEP4 TAPPED MTG. HOLES

G

E

AA

Style f Side Tapped

2 4

CB CWCW

3

1

L M

CD

PIVOT PIN

LRMR

Style BB Cap Fixed Clevis

(NFPA MS4)

(NFPA MP�)

(NFPA MS2)

(NFPA MT�)


Catalog PH00�/NA

Cylinders

6

Bore NT R SB ST SU SW TD TF TL TN TS UF US UT LB P SN SS

1 1/2 1/4-20 1.43 7/16 1/2 15/16 3/8 1.000 2 3/4 1 5/8 2 3/4 3 3/8 3 1/2 4 4 2 1/4 2 1/4 2 7/8

2 5/16-18 1.84 7/16 1/2 15/16 3/8 1.000 3 3/8 1 7/8 3 1/4 4 1/8 4 4 1/2 4 2 1/4 2 1/4 2 7/8

2 1/2 3/8-16 2.19 7/16 1/2 15/16 3/8 1.000 3 7/8 1 1 1/4 3 3/4 4 5/8 4 1/2 5 4 1/8 2 3/8 2 3/8 3

3 1/4 1/2-13 2.76 9/16 3/4 1 1/4 1/2 1.000 4 11/16 1 1 1/2 4 3/4 5 1/2 5 3/4 5 3/4 4 7/8 2 5/8 2 5/8 3 1/4

4 1/2-13 3.32 9/16 3/4 1 1/4 1/2 1.000 5 7/16 1 2 1/16 5 1/2 6 1/4 6 1/2 6 1/2 4 7/8 2 5/8 2 5/8 3 1/4


Bore AA BB CB CD CW DD E NPTF† SAE* F FB G J K L LR M MR

1 1/2 2.02 1 3/4 .501 1/2 1/4-28 2 3/8** 6# 3/8 5/16 1 1/2 1 1/4 3/4 3/4 1/2 5/8

2 2.6 1 1/8 3/4 .501 1/2 5/16-24 2 1/2 3/8** 6 3/8 3/8 1 1/2 1 5/16 3/4 3/4 1/2 5/8

2 1/2 3.1 1 1/8 3/4 .501 1/2 5/16-24 3 3/8** 6 3/8 3/8 1 1/2 1 5/16 3/4 3/4 1/2 5/8

3 1/4 3.9 1 3/8 1 1/4 .751 5/8 3/8-24 3 3/4 1/2 10 5/8 7/16 1 3/4 1 1/4 3/8 1 1/4 1 3/4 15/16

4 4.7 1 3/8 1 1/4 .751 5/8 3/8-24 4 1/2 1/2 10 5/8 7/16 1 3/4 1 1/4 3/8 1 1/4 1 3/4 15/16

MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS


** On ��/2”, 2” and 2�/2” bore sizes, the head-end (only) pipe thread is not full depth on cylinders with No. 2 rods. Minimum of three full threads available.

† Series 3L only: NPTF ports will be furnished as standard unless SAE straight thread ports are specified.

* Series 3L only: SAE straight thread ports are indicated by port number.

# Straight thread ports on ��/2” bore cap end, and head end with Code 2 rod, require an adapter fitting. (See “Straight Thread Port Adapter” drawing on bottom of page.) Adapters are furnished as standard.

MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

CC

D WRENCHFLATS

MM B

NA

V

A

WC

18

KK

D WRENCHFLATS

MM B

NA

VWA

LA

C

18

KK

D WRENCHFLATS

rod end Dimensions — See table 2thread Style 4(NFPA Style SM) Small Male

Straight thread Port adapters

Used on ��/2” bore cap end and on head end of ��/2” bore with Code 2 rod.

Special thread Style 3To order, specify “Style 3” and give desired dimensions for CC or KK, A and LA. If otherwise special, furnish dimensional sketch.

A high strength rod end stud is supplied on thread style 4 through 2” diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured against the rod shoulder. When the workpiece is not shouldered,

style 4 rod ends are recommended through 2” piston rod diameters and style 8 rod ends are recommended on larger diameters. Use style � for applications where female rod end threads are required. If rod end is not specified, style 4 will be supplied.

34

EE

thread Style 8(NFPA Style IM) Intermediate Male

thread Style 9(NFPA Style SF) Short Female


Bore

RodDia.MM

2A RodNo.

3L RodNo.

Style 8

CC

Style 4 & 9

KK A

+.000-.002

B C D LA NA V W Y XG XS XT

Add Stroke

XF

1 1/25/8 1(Std.) 1(Std.) 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 5/8

1 2 2 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5

2

5/8 1(Std.) 1(Std.) 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 5/8

1 3/8 2 2 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 7/8 1 5/16 5/8 1 1/4 2 9/16 2 3/8 2 2 9/16 5 1/4

1 3 3 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5

2 1/2

5/8 1(Std.) 7 1/2-20 7/16-20 3/4 1.124 3/8 1/2 1 3/8 9/16 1/4 5/8 1 15/16 1 3/4 1 3/8 1 15/16 4 3/4

1 3/4 2 2 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 3 1/2 1 11/16 3/4 1 1/2 2 13/16 2 5/8 2 1/4 2 13/16 5 5/8

1 3 1(Std.) 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 2 1/8 15/16 1/2 1 2 5/16 2 1/8 1 3/4 2 5/16 5 1/8

3 1/4

1 1(Std.) 1(Std.) 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 1 7/8 15/16 1/4 3/4 2 7/16 2 1/4 1 7/8 2 7/16 5 5/8

2 2 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 3 5/8 1 15/16 1/2 1 3/8 3 1/16 2 7/8 2 1/2 3 1/16 6 1/4

1 3/8 3 3 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 5/8 1 5/16 3/8 1 2 11/16 2 1/2 2 1/8 2 11/16 5 7/8

4

1 1(Std.) 7 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 1 7/8 15/16 1/4 3/4 2 7/16 2 1/4 1 7/8 2 7/16 5 5/8

2 1/2 2 2 2 1/4-12 1 7/8-12 3 3.124 1 2 1/16 4 5/8 2 3/8 5/8 1 5/8 3 5/16 3 1/8 2 3/4 3 5/16 6 1/2

1 3/8 3 1(Std.) 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 2 5/8 1 5/16 3/8 1 2 11/16 2 1/2 2 1/8 2 11/16 5 7/8


1 1/2

2

2 1/2

3 1/4

4

+.000/-.001 Add Stroke

+.000/-.002 EE


Catalog PH00�/NA

Cylinders

notes

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________


Catalog PH00�/NA

Cylinders

6

Industrial CylindersSeries 2H


How to orDer

Bore* Specify in inches –

Cushion- Used only if cushion required C Head

mounting* Head Tie Rods Extended TB Style Cap Tie Rods Extended TC Both End Tie Rods Extended TD Head Rectangular Flange J Head Rectangular JJ Cap Rectangular Flange H Side Lugs C† Cap Fixed Clevis BB Head Trunnion D Side Tapped F

Series* Used in all 2H Model Numbers –2H

Piston Ring packed piston standard C Used only for Lipseal® Piston L Used only for Hi-Load Piston K

Ports* SAE Straight Thread O-Ring Port (Standard) T NPTF (Dry Seal Pipe Thread) U

Common Fluorocarbon Seals V modifications (See Operating Fluids/Seals page)

Special Used only if special modifications modifications are required: Oversize Ports Port Position Change Rod End Bellows S Special Seals Stop Tube Stroke Adjuster Tie Rod Supports

Piston rod* For Single Rod Cylinders, � number select one only. (See Piston Rod - 2 Stroke Selection Chart - for 3 minimum piston rod diameter.)

Piston* Select: rod end Style 4 Small Male 4 Style 8 Intermediate Male 8 Style � Short Female � Style 3 Special (specify) 3

Piston rod* UNF Standard A threads

Cushion-Cap Used only if cushion required C

Stroke* Specify in inches –

Series 2H model numbers – How to Develop them – How to “Decode” them

Parker Series 2H cylinders can be completely and accurately described by a model number consisting of coded symbols. To develop a model number, select only those symbols that

represent the cylinder required, and place them in the sequence indicated below.

feature Description Symbol

Use Symbol S to designate any specialmodification except piston rod end.

* Required for Basic Cylinder Model Number† Cylinders with these mounting styles should have a minimum stroke length equal to or greater than their bore size.

4” t V S 1 4 C 12”l–2HC f a

Styles 4, 8 and � are catalog standards.Specify Style 3 for any special piston rod end.

Dark arrows indicate Basic Minimum Model Number.

Cylinder serial numbers are factory production record numbers and are assigned to each cylinder, in addition to the model number.


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2H


SerieS 2H HeaVy Duty HyDrauliC CylinDerS

4 2E R

TFRTFB

4 HOLES

3

1

RD

LG + STROKE

UFA

C

NA

KK

D WRENCHFLATS

WFRT

WF

KB

B

18

MM

4 2E R

TFFFB

4 HOLES

3

1 WUF

WF

MM

4 2E R

R GFBBDD

J3

1

LB + STROKE

P + STROKE

W K

EE

Y

AA

E

MM

42R E

TF

3

1UF

FFB4 HOLES

Styles tB, tC, tD Tie Rods Extended*

Style J Head Rectangular Flange

Style JJ Head Rectangular

Style H Cap Rectangular Flange

(NFPA MX3)

(NFPA MF2)

(NFPA MF�)

* Basic Mounting (T) — NFPA MX0 — no tie rods extended can be supplied upon request.

Style TB (NFPA MX3). Head Tie Rods Extended, illustrated: Style TC (NFPA MX2), Cap Tie Rods Extended; and Style TD (NFPA MX�), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned from Style TB drawing at left.

Series 2H Pressure limitation for Style ‘H’ mount

Series 2H Pressure limitation for Style ‘J’ mount

* Maximum pressure rating - push application.

Bore Size 1 2 3

1 1/2 2500 3000 –

2 3000 3000 –

2 1/2 3000 3000 3000

3 1/4 3000 3000 3000

4 3000 3000 3000


* Maximum pressure rating - pull application.

Bore Size 1 2 3

1 1/2 1500 1000 –

2 2000 1200 –

2 1/2 2000 1100 1500

3 1/4 1800 1300 1400

4 1800 1300 1700


(NFPA ME5)


Catalog PH00�/NA

Cylinders

6



table 2 – rod Dimensions


† NPTF ports are available at no extra charge.* Dimension CD is pin diameter.** SAE straight thread ports are standard and are indicated by port number.

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

rod end Dimensions — see table 2

thread Style 9(NFPA Style SF)Small Female

thread Style 8(NFPA Style IM)Intermediate Male

thread Style 4(NFPA Style SM)Small Male

A high strength rod end stud is supplied on thread style 4 through 2” diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured against the rod shoulder. When the workpiece is not shouldered, style 4 rod

ends are recommended through 2” piston rod diameters and style 8 rod ends are recommended on larger diameters. Use style � for applications where female rod end threads are required. If rod end is not specified, style 4 will be supplied.

“Special” threadStyle 3Special thread, extension, rod eye, blank, etc., are also available. To order, specify “Style 3” and give desired dimensions for CC or KK, A and LA. If otherwise special, furnish dimensioned sketch.

BoreRodNo.

Rod Dia.MM

Style8

CC

Style 4 & 9

KK A

+.000-.002

B C D KB LA NA V W RD RT WF Y

11/21(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 0 1 3/8 9/16 1/4 5/8 2 1/8 3/8 1 2

2 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 2 1/8 15/16 1/2 1 2 1/2 3/8 1 3/8 2 3/8

21(Std.) 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 1 7/8 15/16 1/4 3/4 2 1/2 3/8 1 3/8 2 3/8

2 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 5/8 1 5/16 3/8 1 3 3/8 1 5/8 2 5/8

21/21(Std.) 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 1 7/8 15/16 1/4 3/4 2 1/2 3/8 1 3/8 2 3/8

2 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 1/4 1 11/16 1/2 1 1/4 3 1/2 3/8 1 7/8 2 7/83 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 5/8 1 5/16 3/8 1 3 3/8 1 5/8 2 5/8

31/41(Std.) 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 1/2 1 5/16 1/4 7/8 3 3/8 1 5/8 2 3/4

2 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 1/8 3 1/2 1 15/16 3/8 1 1/4 4 5/8 2 3 1/83 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 1/8 1 11/16 3/8 1 1/8 3 1/2 3/8 1 7/8 3

41(Std.) 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 1 11/16 1/4 1 3 1/2 3/8 1 7/8 3

2 2 1/2 2 1/4-12 1 7/8-12 3 3.124 1 2 1/16 1/4 4 3/8 2 3/8 3/8 1 3/8 4 1/2 5/8 2 1/4 3 3/83 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 1/8 3 3/8 1 15/16 1/4 1 1/8 4 5/8 2 3 1/8


1 1/2

2

2 1/2

3 1/4

4

Bore AA BB CB

+.000-.002CD* CW DD E NPTF† SAE** F

1 1/2 2.3 1 3/8 3/4 .501 1/2 3/8-24 2 1/2 1/2 10 3/8

2 2.9 1 13/16 1 1/4 .751 5/8 1/2-20 3 1/2 10 5/8

2 1/2 3.6 1 13/16 1 1/4 .751 5/8 1/2-20 3 1/2 1/2 10 5/8

3 1/4 4.6 2 5/16 1 1/2 1.001 3/4 5/8-18 4 1/2 3/4 12 3/4

4 5.4 2 5/16 2 1.376 1 5/8-18 5 3/4 12 7/8

Bore FB G J K R TF UF LB LG P

1 1/2 7/16 1 3/4 1 1/2 3/8 1.63 3 7/16 4 1/4 5 4 5/8 2 7/8

2 9/16 1 3/4 1 1/2 7/16 2.05 4 1/8 5 1/8 5 1/4 4 5/8 2 7/8

2 1/2 9/16 1 3/4 1 1/2 7/16 2.55 4 5/8 5 5/8 5 3/8 4 3/4 3

3 1/4 11/16 2 1 3/4 9/16 3.25 5 7/8 7 1/8 6 1/4 5 1/2 3 1/2

4 11/16 2 1 3/4 9/16 3.82 6 3/8 7 5/8 6 5/8 5 3/4 3 3/4

EE

Add Stroke


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2H


SerieS 2H HeaVy Duty HyDrauliC CylinDerS

4

ST

E-.0052-.010

E

TS

SW

SW

SW

SW

XS SS + STROKE

SB4 HOLES

3

1US

2

SU SUSW SW

42

CBCW CWM3

1CD

PIVOT PIN

L

LR

MR

4 2E

E -.0052 -.010

TN F

XT SN + STROKENT THREAD, ND DEEP4 TAPPED MTG. HOLES

3

1

LB + STROKE

P + STROKE

W K

EE

Y

E

JG

MM

AA

Style f Side Tap

Style BB Cap Fixed Clevis

Style C Side Lug

Style D Head Trunnion

(NFPA MS4)

(NFPA MP�)

(NFPA MS2)

(NFPA MT�)

4 2 TD

R18

ETL TL XG3

1UT

maximum Pressure rating - PSi

Bore Size PSI

1 1/2 3000

2 3000

2 1/2 3000

3 1/4 2800

4 1800


Catalog PH00�/NA

Cylinders

6




† NPTF ports are available at no extra charge.* Dimension CD is pin diameter.** SAE straight thread ports are standard and are indicated by port number.

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

CC

LA

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

MM B

NAD WRENCHFLATS

W

VC

18

A

KK

LA

MM B

NAD WRENCHFLATS

rod end Dimensions — see table 2

thread Style 9(NFPA Style SF)Small Female

thread Style 8(NFPA Style IM)Intermediate Male

thread Style 4(NFPA Style SM)Small Male

A high strength rod end stud is supplied on thread style 4 through 2” diameter rods. Larger sizes or special rod ends are cut threads. Style 4 rod ends are recommended where the workpiece is secured against the rod shoulder. When the workpiece is not shouldered, style 4 rod

ends are recommended through 2” piston rod diameters and style 8 rod ends are recommended on larger diameters. Use style � for applications where female rod end threads are required. If rod end is not specified, style 4 will be supplied.

“Special” threadStyle 3Special thread, extension, rod eye, blank, etc., are also available. To order, specify “Style 3” and give desired dimensions for CC or KK, A and LA. If otherwise special, furnish dimensioned sketch.

Bore AA CB

+.000-.002CD CW E NPTF† SAE* F G J K L LR M MR ND

1 1/2 2.3 3/4 .501 1/2 2 1/2 1/2 10 3/8 1 3/4 1 1/2 3/8 3/4 9/16 1/2 5/8 3/8

2 2.9 1 1/4 .751 5/8 3 1/2 10 5/8 1 3/4 1 1/2 7/16 1 1/4 1 3/4 15/16 7/16

2 1/2 3.6 1 1/4 .751 5/8 3 1/2 1/2 10 5/8 1 3/4 1 1/2 7/16 1 1/4 15/16 3/4 15/16 1/2

3 1/4 4.6 1 1/2 1.001 3/4 4 1/2 3/4 12 3/4 2 1 3/4 9/16 1 1/2 1 1/4 1 1 3/16 11/16

4 5.4 2 1.376 1 5 3/4 12 7/8 2 1 3/4 9/16 2 1/8 1 3/4 1 3/8 1 5/8 11/16

Bore NT SB ST SU SW

+.000-.001

TD TL TN TS US UT LB P SN SS

1 1/2 3/8-16 7/16 1/2 15/16 3/8 1.000 1 3/4 3 1/4 4 4 1/2 5 2 7/8 2 7/8 3 7/8

2 1/2-13 9/16 3/4 1 1/4 1/2 1.375 1 3/8 15/16 4 5 5 3/4 5 1/4 2 7/8 2 7/8 3 5/8

2 1/2 5/8-11 13/16 1 1 9/16 11/16 1.375 1 3/8 1 5/16 4 7/8 6 1/4 6 1/4 5 3/8 3 3 3 3/8

3 1/4 3/4-10 13/16 1 1 9/16 11/16 1.750 1 3/4 1 1/2 5 7/8 7 1/4 8 6 1/4 3 1/2 3 1/2 4 1/8

4 1-8 1 1/16 1 1/4 2 7/8 1.750 1 3/4 2 1/16 6 3/4 8 1/2 8 1/2 6 5/8 3 3/4 3 3/4 4

EE

Add Stroke

BoreRodNo.

RodDia.MM

Style8

CC

Style4 & 9

KK A

+.000-.002

B C D KB LA LAF NA V W RD RT XG XS XT Y

11/21(Std.) 5/8 1/2-20 7/16-20 3/4 1.124 3/8 1/2 0 1 3/8 1 3/4 9/16 1/4 5/8 2 1/8 3/8 1 7/8 1 3/8 2 2

2 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 2 1/8 2 1/2 15/16 1/2 1 2 1/2 3/8 2 1/4 1 3/4 2 3/8 2 3/8

21(Std.) 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 1 7/8 2 1/2 15/16 1/4 3/4 2 1/2 3/8 2 1/4 1 7/8 2 3/8 2 3/8

2 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 5/8 3 1/4 1 5/16 3/8 1 3 3/8 2 1/2 2 1/8 2 5/8 2 5/8

21/21(Std.) 1 7/8-14 3/4-16 1 1/8 1.499 1/2 7/8 0 1 7/8 2 1/2 15/16 1/4 3/4 2 1/2 3/8 2 1/4 2 1/16 2 3/8 2 3/8

2 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 1/4 3 7/8 1 11/16 1/2 1 1/4 3 1/2 3/8 2 3/4 2 9/16 2 7/8 2 7/83 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 5/8 3 1/4 1 5/16 3/8 1 3 3/8 2 1/2 2 5/16 2 5/8 2 5/8

31/41(Std.) 1 3/8 1 1/4-12 1-14 1 5/8 1.999 5/8 1 1/8 1/4 2 1/2 3 1/4 1 5/16 1/4 7/8 3 3/8 2 5/8 2 5/16 2 3/4 2 3/4

2 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 1/8 3 1/2 4 1/4 1 15/16 3/8 1 1/4 4 5/8 3 2 11/16 3 1/8 3 1/83 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 1/8 3 7/8 1 11/16 3/8 1 1/8 3 1/2 3/8 2 7/8 2 9/16 3 3

41(Std.) 1 3/4 1 1/2-12 1 1/4-12 2 2.374 3/4 1 1/2 1/4 3 3 7/8 1 11/16 1/4 1 3 1/2 3/8 2 7/8 2 3/4 3 3

2 2 1/2 2 1/4-12 1 7/8-12 3 3.124 1 2 1/16 1/4 4 3/8 5 1/4 2 3/8 3/8 1 3/8 4 1/2 5/8 3 1/4 3 1/8 3 3/8 3 3/83 2 1 3/4-12 1 1/2-12 2 1/4 2.624 7/8 1 11/16 1/8 3 3/8 4 1/4 1 15/16 1/4 1 1/8 4 5/8 3 2 7/8 3 1/8 3 1/8


1 1/2

2

2 1/2

3 1/4

4


Catalog PH00�/NA

CylindersIndustrial Cylinder Mountingsrod Clevis - mounting Plate/eye Bracket

* Cylinder accessory dimensions conform to NFPA recommended standard NFPA/T3.6.8 R�-��84, NFPA recommended standard fluid power systems – cylinder – dimensions for

accessories for cataloged square head industrial cylinders.

ThreadSize Part No.

Load Capacity(Lbs.) Part No.


Shear Capacity(Lbs.)

7/16-20 0509400000 4250 0691950000 4100 0683680000 8600

1/2-20 0509410000 4900 0691950000 4100 0683680000 8600

3/4-16 0509420000 11200 0691960000 10500 0683690000 19300

3/4-16 1332840000 11200 0691960000 10500 0683690000 19300

7/8-14 0509430000 18800 *0853610000 20400 0683700000 34300

1-14 0509440000 19500 *0853610000 20400 0683700000 34300

1-14 1332850000 19500 *0853610000 20400 0683700000 34300

1 1/4-12 0509450000 33500 0691980000 21200 0683710000 65000

1 1/4-12 1332860000 33500 0691980000 21200 0683710000 65000

1 1/2-12 0509460000 45600 *0853620000 49480 0683720000 105200

1 3/4-12 0509470000 65600 *0853630000 70000 0683730000 137400

1 7/8-12 0509480000 65600 *0853630000 70000 0683730000 137400

2 1/4-12 0509490000 98200 *0853640000 94200 0683740000 214700

Rod Clevis Mounting Plate/Eye Bracket Pivot Pin

General Description: Cylinder accessories – Parker offers a complete range of cylinder accessories to assure you of the greatest versatility in present and future cylinder applications.

rod end accessories – Accessories offered for the rod end of the cylinder include Rod Clevis, Eye Bracket, Knuckle, Clevis Bracket, and Pivot Pin. To select the proper part number for any desired accessory, refer to the table below or on the opposite page and look in the row to the right of the rod thread in the first column. For economical accessory selection, it is recommended that rod end style 4 be specified on your cylinder order.

accessory load Capacity – The various accessories have been load rated for your convenience. The load capacity in lbs. is the recommended maximum load for that accessory based on a 4:� design factor in tension. (Pivot Pin is rated in shear). Before specifying, compare the actual load or the tension (pull) force at maximum operating pressure of the cylinder with the load capacity of the accessory you plan to use. If load or pull force of cylinder exceeds load capacity of accessory, consult factory.

CylinDer mountinGS

roD CleViS - mountinG Plate/eye BraCket


Catalog PH00�/NA

Cylinders

6

Part No. A CB CD CE CW ER KK

0509400000 3/4 3/4 1/2 1 1/2 1/2 1/2 7/16-20

0509410000 3/4 3/4 1/2 1 1/2 1/2 1/2 1/2-20

0509420000 1 1/8 1 1/4 3/4 2 1/8 5/8 3/4 3/4-16

1332840000 1 1/8 1 1/4 3/4 2 3/8 5/8 3/4 3/4-16

0509430000 1 5/8 1 1/2 1 2 15/16 3/4 1 7/8-14

0509440000 1 5/8 1 1/2 1 2 15/16 3/4 1 1-14

1332850000 1 5/8 1 1/2 1 3 1/8 3/4 1 1-14

0509450000 1 7/8 2 1 3/8 3 3/4 1 1 3/8 1 1/4-12

1332860000 2 2 1 3/8 4 1/8 1 1 3/8 1 1/4-12

0509460000 2 1/4 2 1/2 1 3/4 4 1/2 1 1/4 1 3/4 1 1/2-12

0509470000 3 2 1/2 2 5 1/2 1 1/4 2 1 3/4-12

0509480000 3 2 1/2 2 5 1/2 1 1/4 2 1 7/8-12

0509490000 3 1/2 3 2 1/2 6 1/2 1 1/2 2 1/2 2 1/4-12

Industrial Cylinder Mountingsrod Clevis - mounting Plate/eye Bracket

CylinDer mountinGS

roD CleViS

�. Pivot Pins are furnished with Clevis Mounted Cylinders as standard.

2. Pivot Pins are furnished with (2) Retainer Rings.

3. Pivot Pins must be ordered as a separate item if to be used with Knuckles, Rod Clevises, or Clevis Brackets.

* Cylinder accessory dimensions conform to NFPA recommended standard NFPA/T3.6.8 R�-��84, NFPA recommended standard fluid power systems – cylinder – dimensions for accessories for cataloged square head industrial cylinders.

MR

LR

RE

DD DIA4 HOLES

F

M 25˚

FL

CB

+ .004+ .002

RE

CD �. When used to mate with the Rod Clevis, select Eye Bracket by thread size in table on opposite page.

2. When used to mount the Style BB Cylinders, select Mounting Plate by bore size below.

CBCW CWER

KK THREAD

+.004+.002CD

A

CE

Pivot Pin Dimensions

CL

CD+.001-.002

Part No. CB CD DD E F FL LR M MR R 2A/3L Bore 2H Bore

0691950000 3/4 1/2 13/32 2 1/2 3/8 1 1/8 3/4 1/2 9/16 1.63 1 1/2”, 2”, 2 1/2” 1 1/2”

0691960000 1 1/4 3/4 17/32 3 1/2 5/8 1 7/8 1 1/4 3/4 7/8 2.55 3 1/4”, 4” 2”, 2 1/2”

*0853610000 1 1/2 1 21/32 4 1/2 7/8 2 3/8 1 1/2 1 1 1/4 3.25 – 3 1/4”

0691980000 2 1 3/8 21/32 5 7/8 3 2 1/8 1 3/8 1 5/8 3.82 – 4”

*0853620000 2 1/2 1 3/4 29/32 6 1/2 1 1/8 3 3/8 2 1/4 1 3/4 2 1/8 4.95 – –

*0853630000 2 1/2 2 1 1/16 7 1/2 1 1/2 4 2 1/2 2 2 7/16 5.73 – –

*0853640000 3 2 1/2 1 3/16 8 1/2 1 3/4 4 3/4 3 2 1/2 3 6.58 – –

Part Number CD CL

0683680000 1/2 1 7/8

0683690000 3/4 2 5/8

0683700000 1 3 1/8

0683710000 1 3/8 4 1/8

0683720000 1 3/4 5 3/16

0683730000 2 5 3/16

0683740000 2 1/2 6 3/16

CylinDer mountinGS

mountinG Plate/eye BraCket

Dimensions


Catalog PH00�/NA

CylindersIndustrial Cylinder Mountingsknuckle - Clevis Bracket

ThreadSize Part No.



Shear Capacity

(Lbs.)

7/16-20 0690890000 5000 0692050000 7300 0683680000 8600

1/2-20 0690900000 5700 0692050000 7300 0683680000 8600

3/4-16 0690910000 12100 0692060000 14000 0683690000 19300

3/4-16 0690910000 12100 0692060000 14000 0683690000 19300

7/8-14 0690920000 13000 0692070000 19200 0683700000 34300

1-14 0690930000 21700 0692070000 19200 0683700000 34300

1-14 0690930000 21700 0692070000 19200 0683700000 34300

1 1/4-12 0690940000 33500 0692080000 36900 0683710000 65000

1 1/4-12 0690940000 33500 0692080000 36900 0683710000 65000

1 1/2-12 0690950000 45000 0692090000 34000 0683720000 105200

1 3/4-12 0690960000 53500 0692100000 33000 0692150000 137400

1 7/8-12 0690970000 75000 0692100000 33000 0692150000 137400

2 1/4-12 0690980000 98700 0692110000 34900 0683740000 214700

Knuckle Clevis Bracket Pivot Pin

General Description: Cylinder accessories – Parker offers a complete range of cylinder accessories to assure you of the greatest versatility in present and future cylinder applications.

rod end accessories – Accessories offered for the rod end of the cylinder include Rod Clevis, Eye Bracket, Knuckle, Clevis Bracket, and Pivot Pin. To select the proper part number for any desired accessory, refer to the table below or on the opposite page and look in the row to the right of the rod thread in the first column. For economical accessory selection, it is recommended that rod end style 4 be specified on your cylinder order.

accessory load Capacity – The various accessories have been load rated for your convenience. The load capacity in lbs. is the recommended maximum load for that accessory based on a 4:� design factor in tension. (Pivot Pin is rated in shear). Before specifying, compare the actual load or the tension (pull) force at maximum operating pressure of the cylinder with the load capacity of the accessory you plan to use. If load or pull force of cylinder exceeds load capacity of accessory, consult factory.

CylinDer mountinGS

knuCkle - CleViS BraCket


Catalog PH00�/NA

Cylinders

6

Part No. A CA CB CD ER KK

0690890000 3/4 1 1/2 3/4 1/2 23/32 7/16-20

0690900000 3/4 1 1/2 3/4 1/2 23/32 1/2-20

0690910000 1 1/8 2 1/16 1 1/4 3/4 1 1/16 3/4-16

0690920000 1 1/8 2 3/8 1 1/2 1 1 7/16 7/8-14

0690930000 1 5/8 2 13/16 1 1/2 1 1 7/16 1-14

0690940000 2 3 7/16 2 1 3/8 1 31/32 1 1/4-12

0690950000 2 1/4 4 2 1/2 1 3/4 2 1/2 1 1/2-12

0690960000 2 1/4 4 3/8 2 1/2 2 2 27/32 1 3/4-12

0690970000 3 5 2 1/2 2 2 27/32 1 7/8-12

0690980000 3 1/2 5 13/16 3 2 1/2 3 9/16 2 1/4-12

Part No. CD CL

0683680000 1/2 1 7/8

0683690000 3/4 2 5/8

0683700000 1 3 1/8

0683710000 1 3/8 4 1/8

0683720000 1 3/4 5 3/16

0692150000 2 5 11/16

0683740000 2 1/2 6 3/16

Industrial Cylinder Mountingsknuckle - Clevis Bracket

CylinDer mountinGS

knuCkle

Pivot Pin Dimensions

CL

CD+.001-.002

CB

CDER +.004+.002

CD CA

CD

CDKK THREAD

A FULLTHREAD

25˚MR

LR

RE

DD DIA4 HOLES

F

M

FL

CW CWCB

+ .004+ .002

RE

CD

Cylinder accessory dimensions conform to NFPA recommended standard NFPT/T3.6.8 R�-��84, NFPA recommended standard fluid power systems – cylinder – dimensions for accessories for cataloged square head industrial cylinders.

�. Pivot Pins are furnished with Clevis Mounted Cylinders as standard.

2. Pivot Pins are furnished with (2) Retainer Rings.

3. Pivot Pins must be ordered as a separate item if to be used with Knuckles, Rod Clevises, or Clevis Brackets.

Part No. CB CD CW DD E F FL LR M MR R

0740760000 15/32 7/16 3/8 17/64 2 1/4 3/8 1 5/8 3/8 1/2 1.75

0692050000 3/4 1/2 1/2 13/32 3 1/2 1/2 1 1/2 3/4 1/2 5/8 2.55

0692060000 1 1/4 3/4 5/8 17/32 5 5/8 1 7/8 1 3/16 3/4 29/32 3.82

0692070000 1 1/2 1 3/4 21/32 6 1/2 3/4 2 1/4 1 1/2 1 1 1/4 4.95

0692080000 2 1 3/8 1 21/32 7 1/2 7/8 3 2 1 3/8 1 21/32 5.73

0692090000 2 1/2 1 3/4 1 1/4 29/32 9 1/2 7/8 3 5/8 2 3/4 1 3/4 2 7/32 7.50

0692100000 2 1/2 2 1 1/2 1 1/16 12 3/4 1 4 1/4 3 3/16 2 1/4 2 25/32 9.40

0692110000 3 2 1/2 1 1/2 1 3/16 12 3/4 1 4 1/2 3 1/2 2 1/2 3 1/8 9.40

CylinDer mountinGS

CleViS BraCket

Dimensions

Dimensions


Catalog PH00�/NA

CylindersIndustrial Cylinder AccessoriesSeal kits – Standard Seals for Series 2a, 3l, 2H Cylinders

Seal kitS/StanDarD SealS

SerieS 2a, 3l, 2H CylinDerS

For operating temperature and fluid compatibility see Operating Fluids and Seals page in this section.

Gland and spanner wrenches are available to ease (rod) seal or gland cartridge removal without disassembly of the cylinder.

Seal kits for Class 1 & 2 Service

*RG & RK kits listed are not applicable to �0” & �2” bore series 2H cylinders.

*(-0%, +5% tolerance). When assembling the cylinder, be sure to torque the tie rods evenly.

Head end

62

45

14 40 41 45

62

43

Rod Dia.

RGGland (Sym. 62)

Cartridge KitsContains Symbols

14, 40, 41, 43 & 45

RKRod Seal

KitsContains Symbols40, 41, 43 & 45

RGGland (Sym. 62)

Cartridge KitsContains Symbols14, 40, 41 & 45

RKRod Seal

KitsContains Symbols

40, 41 & 451/2 RG2AHL0051 RK2AHL0051 RG2HLTS051 RK2HLTS0515/8 RG2AHL0061 RK2AHL0061 RG2HLTS061 RK2HLTS0611 RG2AHL0101 RK2AHL0101 RG2HLTS101 RK2HLTS101

1 3/8 RG2AHL0131 RK2AHL0131 RG2HLTS131 RK2HLTS1311 3/4 RG2AHL0171 RK2AHL0171 RG2HLTS171 RK2HLTS171

2 RG2AHL0201 RK2AHL0201 RG2HLTS201 RK2HLTS2012 1/2 RG2AHL0251 RK2AHL0251 RG2HLTS251 RK2HLTS251



*5 RG2AHL0501 RK2AHL0501 RG2HLTS501 RK2HLTS501*5 1/2 RG2AHL0551 RK2AHL0551 RG2HLTS551 RK2HLTS551

Series 2A Series 2H & 3L Material: Buna-N (Nitrile) TS 2000 Gland Seal Kits Material: Polyurethane & Buna-N (Nitrile)

BoreSize

PKPiston Seal KitsSeries 2A Only

Contains 2 ea. Sym.:42, 44 & 47

PKPiston Seal Kits

Series 2HL & 3LLContains 2 ea. Sym.:

42, 44 & 47

PRPiston Ring KitsSeries 2H & 3L

Contains 2 ea. Sym.:47 & 48

Hi-LoadPiston Seal Kits

Series 2HContains 2 ea. Sym.:47, 119, 120 & 121

1 PK1002A001 PK102HLL01 PR102H0001 –1 1/2 PK1502A001 PK152HLL01 PR152H0001 PK152HK001

2 PK2002A001 PK202HLL01 PR202H0001 PK202HK0012 1/2 PK2502A001 PK252HLL01 PR252H0001 PK252HK0013 1/4 PK3202A001 PK322HLL01 PR322H0001 PK322HK001

4 PK4002A001 PK402HLL01 PR402H0001 PK402HK0015 PK5002A001 PK502HLL01 PR502H0001 PK502HK0016 PK6002A001 PK602HLL01 PR602H0001 PK602HK0017 PK7002A001 PK702HLL01 PR702H0001 PK702HK0018 PK8002A001 PK802HLL01 PR802H0001 PK802HK00110 PK9002A001 PK902HLL01 PR902H0001 PK902HK00112 PK9202A001 PK922HLL01 PR922H0001 PK922HK00114 PK9402A001 – – –

BoreSize

Series 2AContains 2 ea.

Symbol 47

Series 2H & 3LContains 2 ea.

Symbol 47

Series 2A & 3LCylinder Body Material

Steel

Series 2HCylinder Body Material

Steel1 CB102HL001 CB102HL001 35 in.-lbs. 41 cm-kg – –

1 1/2 CB152HL001 CB152HL001 60 in.-lbs. 69 cm-kg 18 ft.-lbs. 24 N.m2 CB202HL001 CB202HL001 11 ft.-lbs. 15 N.m 45 ft.-lbs. 61 N.m

2 1/2 CB252HL001 CB252HL001 11 ft.-lbs. 15 N.m 45 ft.-lbs. 61 N.m3 1/4 CB322A0001 CB322HL001 25 ft.-lbs. 34 N.m 120 ft.-lbs. 163 N.m

4 CB402A0001 CB402HL001 25 ft.-lbs. 34 N.m 131 ft.-lbs. 178 N.m5 CB502A0001 CB502HL001 60 ft.-lbs. 81 N.m 312 ft.-lbs. 423 N.m6 CB602A0001 CB602HL001 60 ft.-lbs. 81 N.m 528 ft.-lbs. 716 N.m7 CB702A0001 CB702HL001 90 ft.-lbs. 122 N.m 800 ft.-lbs. 1085 N.m8 CB802A0001 CB802HL001 110 ft.-lbs. 149 N.m 1168 ft.-lbs. 1584 N.m10 CB902A0001 CB902HL001 148 ft.-lbs. 201 N.m – –12 CB922A0001 CB922HL001 172 ft.-lbs. 233 N.m – –14 – – 275 ft.-lbs. 373 N.m – –

CB Cylinder Body Seal Kits Tie Rod Torque Specifications*


Catalog PH00�/NA

Cylinders

6

Industrial Cylinder AccessoriesSeal kits – Group 5 for Series 2a, 3l, 2H Cylinders

Seal kitS/GrouP 5

SerieS 2a, 3l, 2H CylinDerS

42

44

�2�

��20

�4

40

43

4�

45

47

48

47

62

42

44

�2�

��20

�4

40

43

4�

45

47

48

47

62

*(-0%, +5% tolerance). When assembling the cylinder, be sure to torque the tie rods evenly.

Seal kits for Class 5 ServiceMaterial: FluorocarbonFor operating temperature and fluid compatibility see Cylinder Engineering Section.Gland and spanner wrenches are available to ease (rod) seal or gland cartridge removal without disassembly of the cylinder.

*RG & RK kits listed are not applicable to �0” & �2” bore series 2H cylinders. See bulletin 0��5-M4.

Piston Seal options

ring type Piston(as shown above) Supplied on series 2H & 3L hydraulic cylinders.

lipseal type Piston

Supplied on series 2A air cylinders and series 2H & 3L hydraulic cylinders.

Hi-load type Piston

Optional on series 2H hydraulic cylinders. Not available on series 2A & 3L cylinders.

Symbol Description �4 Gland cartridge 40 Gland wiperseal 4� Gland lipseal 42 Piston lipseal 43 Gland back-up washer 44 Piston back-up washer 45 Gland to head o-ring 47 End seal o-ring 48 Piston ring 62 Gland cartridge kit �� Outer ring �20 Inner ring �2� Wear ring

42

44

121

119120

14

40

43

41

45

47

48

47

62

Rod Dia.

RGGland (Sym. 62)

Cartridge KitsContains Symbols

14, 40, 41, 43 & 45

RKRod Seal

KitsContains Symbols40, 41, 43 & 45

GlandWrench

SpannerWrench

1/2 RG2AHL0055 RK2AHL0055 0695900000 01167600005/8 RG2AHL0065 RK2AHL0065 0695900000 01167600001 RG2AHL0105 RK2AHL0105 0695910000 0116760000

1 3/8 RG2AHL0135 RK2AHL0135 0695920000 01170300001 3/4 RG2AHL0175 RK2AHL0175 0695930000 0116770000

2 RG2AHL0205 RK2AHL0205 0695940000 01167700002 1/2 RG2AHL0255 RK2AHL0255 0695950000 0116770000



*5 RG2AHL0505 RK2AHL0505 0695990000 0116780000*5 1/2 RG2AHL0555 RK2AHL0555 0696000000 0116780000

Series 2A, 2H, 3L Cylinders

BoreSize

PKPiston Seal KitsSeries 2A Only

Contains 2 ea. Sym.:42, 44 & 47

PKPiston Seal Kits

Series 2HL & 3LLContains 2 ea. Sym.:

42, 44 & 47

PRPiston Ring KitsSeries 2H & 3L

Contains 2 ea. Sym.:47 & 48

Hi-LoadPiston Seal Kits

Series 2HContains 2 ea. Sym.:47, 119, 120 & 121

1 PK1002A005 PK102HLL05 PR102H0005 –1 1/2 PK1502A005 PK152HLL05 PR152H0005 PK152HK005

2 PK2002A005 PK202HLL05 PR202H0005 PK202HK0052 1/2 PK2502A005 PK252HLL05 PR252H0005 PK252HK0053 1/4 PK3202A005 PK322HLL05 PR322H0005 PK322HK005

4 PK4002A005 PK402HLL05 PR402H0005 PK402HK0055 PK5002A005 PK502HLL05 PR502H0005 PK502HK0056 PK6002A005 PK602HLL05 PR602H0005 PK602HK0057 PK7002A005 PK702HLL05 PR702H0005 PK702HK0058 PK8002A005 PK802HLL05 PR802H0005 PK802HK00510 PK9002A005 PK902HLL05 PR902H0005 PK902HK00512 PK9202A005 PK922HLL05 PR922H0005 PK922HK00514 PK9402A005 – – –

BoreSize

Series 2AContains 2 ea.

Symbol 47

Series 2H & 3LContains 2 ea.

Symbol 47

Series 2A & 3LCylinder Body Material

Steel

Series 2HCylinder Body Material

Steel1 CB102HL005 CB102HL005 35 in.-lbs. 41 cm-kg – –

1 1/2 CB152HL005 CB152HL005 60 in.-lbs. 69 cm-kg 18 ft.-lbs. 24 N.m2 CB202HL005 CB202HL005 11 ft.-lbs. 15 N.m 45 ft.-lbs. 61 N.m

2 1/2 CB252HL005 CB252HL005 11 ft.-lbs. 15 N.m 45 ft.-lbs. 61 N.m3 1/4 CB322HL005 25 ft.-lbs. 34 N.m 120 ft.-lbs. 163 N.m

4 CB402HL005 25 ft.-lbs. 34 N.m 131 ft.-lbs. 178 N.m5 CB502HL005 60 ft.-lbs. 81 N.m 312 ft.-lbs. 423 N.m6 CB602HL005 60 ft.-lbs. 81 N.m 528 ft.-lbs. 716 N.m7 CB702HL005 90 ft.-lbs. 122 N.m 800 ft.-lbs. 1085 N.m8 CB802HL005 110 ft.-lbs. 149 N.m 1168 ft.-lbs. 1584 N.m10 CB902HL005 148 ft.-lbs. 201 N.m – –12 CB922HL005 172 ft.-lbs. 233 N.m – –14 – 275 ft.-lbs. 373 N.m – –

CB Cylinder Body Seal Kits Tie Rod Torque Specifications*

USE(PK)

PISTONSEALKITSFOR

THESESIZES


Catalog PH00�/NA

CylindersIndustrial CylindersSeries 2a, 3l, 2H


Safety GuiDe for SeleCtinG anD uSinG HyDrauliC, PneumatiC CylinDerS anD tHeir aCCeSSorieS

Before selecting or using Parker (The Company) cylinders or related accessories, it is important that you read, understand and follow the following safety information. Training is advised before selecting and using The Company’s products.

1.0 General instructions 1.1 Scope – This safety guide provides instructions for selecting and using

(including assembling, installing, and maintaining) cylinder products. This safety guide is a supplement to and is to be used with the specific Company publications for the specific cylinder products that are being considered for use.

1.2 fail Safe – Cylinder products can and do fail without warning for many reasons. All systems and equipment should be designed in a fail-safe mode so that if the failure of a cylinder product occurs people and property won’t be endangered.

1.3 Distribution – Provide a free copy of this safety guide to each person responsible for selecting or using cylinder products. Do not select or use The Company’s cylinders without thoroughly reading and understanding this safety guide as well as the specific Company publications for the products considered or selected.

1.4 user responsibility – Due to a very wide variety of cylinder applications and cylinder operating conditions, The Company does not warrant that any particular cylinder is suitable for any specific application. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The hydraulic and pneumatic cylinders outlined in this catalog are designed to The Company’s design guidelines and do not necessarily meet the design guideline of other agencies such as American Bureau of Shipping, ASME Pressure Vessel Code etc. The user, through its own analysis and testing, is solely responsible for:

• Making the final selection of the cylinders and related accessories.

• Determining if the cylinders are required to meet specific design requirements as required by the Agency(s) or industry standards covering the design of the user’s equipment.

• Assuring that the user’s requirements are met, OSHA requirements are met, and safety guidelines from the applicable agencies such as but not limited to ANSI are followed and that the use presents no health or safety hazards.

• Providing all appropriate health and safety warnings on the equipment on which the cylinders are used.

1.5 additional Questions – Call the appropriate Company technical service department if you have any questions or require any additional information. See the Company publication for the product being considered or used, or call 847-2�8-2400 for the appropriate technical service department.

2.0 Cylinder and accessories Selection 2.1 Seals – Part of the process of selecting a cylinder is the selection of

seal compounds. Before making this selection, consult the “seal information page(s)” of the publication for the series of cylinders of interest.

The application of cylinders may allow fluids such as cutting fluids, wash down fluids etc. to come in contact with the external area of the cylinder. These fluids may attack the piston rod wiper and or the primary seal and must be taken into account when selecting and specifying seal compounds.

Dynamic seals will wear. The rate of wear will depend on many operating factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has been improperly serviced. The user must take seal wear into consideration in the application of cylinders.

2.2 Piston rods – Possible consequences of piston rod failure or separation of the piston rod from the piston include, but are not limited to:

• Piston rod and or attached load thrown off at high speed.

• High velocity fluid discharge.

• Piston rod extending when pressure is applied in the piston retract mode.

Piston rods or machine members attached to the piston rod may move suddenly and without warning as a consequence of other conditions occurring to the machine such as, but not limited to:

• Unexpected detachment of the machine member from the piston rod.

• Failure of the pressurized fluid delivery system (hoses, fittings, valves, pumps, compressors) which maintain cylinder position.

• Catastrophic cylinder seal failure leading to sudden loss of pressurized fluid.

• Failure of the machine control system.

Follow the recommendations of the “Piston Rod Selection Chart and Data” in the publication for the series of cylinders of interest. The suggested piston rod diameter in these charts must be followed in order to avoid piston rod buckling.

Piston rods are not normally designed to absorb bending moments or loads which are perpendicular to the axis of piston rod motion. These additional loads can cause the piston rod to fail. If these types of additional loads are expected to be imposed on the piston rod, their magnitude should be made known to our engineering department.

The cylinder user should always make sure that the piston rod is securely attached to the machine member.

On occasion cylinders are ordered with double rods (a piston rod extended from both ends of the cylinder). In some cases a stop is threaded onto one of the piston rods and used as an external stroke adjuster. On occasions spacers are attached to the machine member connected to the piston rod and also used as a stroke adjuster. In both cases the stops will create a pinch point and the user should consider appropriate use of guards. If these external stops are not perpendicular to the mating contact surface, or if debris is trapped between the contact surfaces, a bending moment will be placed on the piston rod, which can lead to piston rod failure. An external stop will also negate the effect of cushioning and will subject the piston rod to impact loading. Those two (2) conditions can cause piston rod failure. Internal stroke adjusters are available with and without cushions. The use of external stroke adjusters should be reviewed with our engineering department.

The piston rod to piston and the stud to piston rod threaded connections are secured with an anaerobic adhesive. The strength of the adhesive decreases with increasing temperature. Cylinders which can be exposed to temperatures above +250°F (+�2�°C) are to be ordered with a non studded piston rod and a pinned piston to rod joint.

2.3 Cushions – Cushions should be considered for cylinder applications when the piston velocity is expected to be over 4 inches/second.

Cylinder cushions are normally designed to absorb the energy of a linear applied load. A rotating mass has considerably more energy than the same mass moving in a linear mode. Cushioning for a rotating mass application should be reviewed by our engineering department.

2.4 Cylinder mountings – Some cylinder mounting configurations may have certain limitations such as, but not limited to, minimum stroke for side or foot mounting cylinders or pressure de-ratings for certain mounts. Carefully review the catalog for these types of restrictions.

Always mount cylinders using the largest possible high tensile alloy steel socket head cap screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size.

2.5 Port fittings – Hydraulic cylinders applied with meter out or deceleration circuits are subject to intensified pressure at piston rod end.

The rod end pressure is approximately equal to:

operating pressure x effective cap end area

effective rod end piston area

Contact your connector supplier for the pressure rating of individual connectors.

warninG: failure of tHe CylinDer, itS PartS, itS mountinG, itS ConneCtionS to otHer oBJeCtS, or itS ControlS Can reSult in: • unanticipated or uncontrolled movement of the cylinder or objects connected to it. • falling of the cylinder or objects held up by it. • fluid escaping from the cylinder, potentially at high velocity.tHeSe eVentS CoulD CauSe DeatH or PerSonal inJury By, for examPle, PerSonS fallinG from HiGH loCationS, BeinG CruSHeD or StruCk By HeaVy or faSt moVinG oBJeCtS, BeinG PuSHeD into DanGerouS eQuiPment or SituationS, or SliPPinG on eSCaPeD fluiD.


Catalog PH00�/NA

Cylinders

6

Industrial CylindersSeries 2a, 3l, 2H

3.0 Cylinder and accessories installation and mounting

3.1 installation

3.1.1 – Cleanliness is an important consideration, and cylinders are shipped with the ports plugged to protect them from contaminants entering the ports. These plugs should not be removed until the piping is to be installed. Before making the connection to the cylinder ports, piping should be thoroughly cleaned to remove all chips or burrs which might have resulted from threading or flaring operations.

3.1.2 – Cylinders operating in an environment where air drying materials are present such as fast-drying chemicals, paint, or weld splatter, or other hazardous conditions such as excessive heat, should have shields installed to prevent damage to the piston rod and piston rod seals.

3.1.3 – Proper alignment of the cylinder piston rod and its mating component on the machine should be checked in both the extended and retracted positions. Improper alignment will result in excessive rod gland and/or cylinder bore wear. On fixed mounting cylinders attaching the piston rod while the rod is retracted will help in achieving proper alignment.

3.1.4 – Sometimes it may be necessary to rotate the piston rod in order to thread the piston rod into the machine member. This operation must always be done with zero pressure being applied to either side of the piston. Failure to follow this procedure may result in loosening the piston to rod-threaded connection. In some rare cases the turning of the piston rod may rotate a threaded piston rod gland and loosen it from the cylinder head. Confirm that this condition is not occurring. If it does, re-tighten the piston rod gland firmly against the cylinder head.

For double rod cylinders it is also important that when attaching or detaching the piston rod from the machine member that the torque be applied to the piston rod end of the cylinder that is directly attaching to the machine member with the opposite end unrestrained. If the design of the machine is such that only the rod end of the cylinder opposite to where the rod attaches to the machine member can be rotated, consult the factory for further instructions.

3.2 mounting recommendations

3.2.1 – Always mount cylinders using the largest possible high tensile alloy steel socket head screws that can fit in the cylinder mounting holes and torque them to the manufacturer’s recommendations for their size.

3.2.2 – Side-Mounted Cylinders – In addition to the mounting bolts, cylinders of this type should be equipped with thrust keys or dowel pins located so as to resist the major load.

3.2.3 – Tie Rod Mounting – Cylinders with tie rod mountings are recommended for applications where mounting space is limited. The standard tie rod extension is shown as BB in dimension tables. Longer or shorter extensions can be supplied. Nuts used for this mounting style should be torqued to the same value as the tie rods for that bore size.

3.2.4 – Flange Mount Cylinders – The controlled diameter of the rod gland extension on head end flange mount cylinders can be used as a pilot to locate the cylinders in relation to the machine. After alignment has been obtained, the flanges may be drilled for pins or dowels to prevent shifting.

3.2.5 – Trunnion Mountings – Cylinders require lubricated bearing blocks with minimum bearing clearances. Bearing blocks should be carefully aligned and rigidly mounted so the trunnions will not be subjected to bending moments. The rod end should also be pivoted with the pivot pin in line and parallel to axis of the trunnion pins.

3.2.6 – Clevis Mountings – Cylinders should be pivoted at both ends with centerline of pins parallel to each other. After cylinder is mounted, be sure to check to assure that the cylinder is free to swing through its working arc without interference from other machine parts.

4.0 Cylinder and accessories maintenance, troubleshooting and replacement

4.1 Storage – At times cylinders are delivered before a customer is ready to install them and must be stored for a period of time. When storage is required the following procedures are recommended.

4.1.1 – Store the cylinders in an indoor area which has a dry, clean and noncorrosive atmosphere. Take care to protect the cylinder from both internal corrosion and external damage.

4.1.2 – Whenever possible cylinders should be stored in a vertical position (piston rod up). This will minimize corrosion due to possible condensation which could occur inside the cylinder. This will also minimize seal damage.

4.1.3 – Port protector plugs should be left in the cylinder until the time of installation.

4.1.4 – If a cylinder is stored full of hydraulic fluid, expansion of the fluid due to temperature changes must be considered. Installing a check valve with free flow out of the cylinder is one method.

4.1.5 – When cylinders are mounted on equipment that is stored outside for extended periods, exposed unpainted surfaces, e.g. piston rod, must be coated with a rust-inhibiting compound to prevent corrosion.

4.2 Cylinder trouble Shooting

4.2.1 – external leakage

4.2.1.1 – Rod seal leakage can generally be traced to worn or damaged seals. Examine the piston rod for dents, gouges or score marks, and replace piston rod if surface is rough.

Rod seal leakage could also be traced to gland wear. If clearance is excessive, replace rod bushing and seal. Rod seal leakage can also be traced to seal deterioration. If seals are soft or gummy or brittle, check compatibility of seal material with lubricant used if air cylinder, or operating fluid if hydraulic cylinder. Replace with seal material, which is compatible with these fluids. If the seals are hard or have lost elasticity, it is usually due to exposure to temperatures in excess of �65°F. (+74°C). Shield the cylinder from the heat source to limit temperature to 350°F (+�77°C) and replace with fluorocarbon seals.

4.2.1.2 – Cylinder body seal leak can generally be traced to loose tie rods. Torque the tie rods to manufacturer’s recommendation for that bore size.

Excessive pressure can also result in cylinder body seal leak. Determine maximum pressure to rated limits. Replace seals and retorque tie rods as in paragraph above. Excessive pressure can also result in cylinder body seal leak. Determine if the pressure rating of the cylinder has been exceeded. If so, bring the operating pressure down to the rating of the cylinder and have the tie rods replaced.

Pinched or extruded cylinder body seal will also result in a leak. Replace cylinder body seal and retorque as in paragraph above.

Cylinder body seal leakage due to loss of radial squeeze which shows up in the form of flat spots or due to wear on the O.D. or I.D. – either of these are symptoms of normal wear due to high cycle rate or length of service. Replace seals as per paragraph above.

4.2.2 – internal leakage

4.2.2.1 – Piston seal leak (by-pass) � to 3 cubic inches per minute leakage is considered normal for piston ring construction. Virtually no static leak with lipseal type seals on piston should be expected. Piston seal wear is a usual cause of piston seal leakage. Replace seals as required.

4.2.2.2 – With lipseal type piston seals excessive back pressure due to over-adjustment of speed control valves could be a direct cause of rapid seal wear. Contamination in a hydraulic system can result in a scored cylinder bore, resulting in rapid seal wear. In either case, replace piston seals as required.

4.2.2.3 – What appears to be piston seal leak, evidenced by the fact that the cylinder drifts, is not always traceable to the piston. To make sure, it is suggested that one side of the cylinder piston be pressurized and the fluid line at the opposite port be disconnected. Observe leakage. If none is evident, seek the cause of cylinder drift in other component parts in the circuit.

4.2.3 – Cylinder fails to move the load

4.2.3.1 – Pneumatic or hydraulic pressure is too low. Check the pressure at the cylinder to make sure it is to circuit requirements.

4.2.3.2 – Piston Seal Leak – Operate the valve to cycle the cylinder and observe fluid flow at valve exhaust ports at end of cylinder stroke. Replace piston seals if flow is excessive.

4.2.3.3 – Cylinder is undersized for the load – Replace cylinder with one of a larger bore size.

4.3 erratic or Chatter operation

4.3.1 – Excessive friction at rod gland or piston bearing due to load misalignment – Correct cylinder-to-load alignment.

4.3.2 – Cylinder sized too close to load requirements – Reduce load or install larger cylinder.

4.3.3 – Erratic operation could be traced to the difference between static and kinetic friction. Install speed control valves to provide a back pressure to control the stroke.

4.4 Cylinder modifications, repairs, or failed Component – Cylinders as shipped from the factory are not to be disassembled and or modified. If cylinders require modifications, these modifications must be done at company locations or by The Company’s certified facilities. The Cylinder Division Engineering Department must be notified in the event of a mechanical fracture or permanent deformation of any cylinder component (excluding seals). This includes a broken piston rod, tie rod, mounting accessory or any other cylinder component. The notification should include all operation and application details. This information will be used to provide an engineered repair that will prevent recurrence of the failure.

It is allowed to disassemble cylinders for the purpose of replacing seals or seal assemblies. However, this work must be done by strictly following all the instructions provided with the seal kits.


Catalog PH00�/NA

Cylinders

notes

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

_________________________________________________________________________________

cylinders - hallmark hose · 2019. 6. 6. · low pressure hydraulic option includes: rod seal buna...

Documents