cvpdc-0914 technical and performance data · pdf filecvpdc-0914 technical and performance...
TRANSCRIPT
CVPDC-0914
TECHNICAL AND PERFORMANCE DATA PRESSURE DROP CHARTS f CHECK VALVES
TITAN
TITAN FLOW CONTROL, INC.
Style: Threaded Ends, Silent Check Valve Style: Threaded Ends, Silent Check ValveModel: CV 20-BZ (Bronze Unit) Model: CV 80-SS (Stainless Steel Unit)
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x - axis) Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x - axis)
Style: Wafer Type, Single Disc Check Valve Style: Wafer Type, Short Pattern, Swing Check ValveModels: CV 31-DI, CV 32-CS/SS Models: CV 12-CS/SS
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x - axis) Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x - axis)
Pressure Drop Equation for Liquids:
Δ P = G × (Q / Cv)2 Δ P = Pressure drop (psi) G = Specific gravity of liquid at 60 °F Cv = Flow coefficient factor Q = Flow rate (GPM)
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
10.1
2 3 4 5 6 7 8 10 20 30 40 50 70 100 200 300 500 700 1000
3/8
1/4
1/2
3/4
1 11/
4
11/
2
2 21/
2
3 4Sizes (in):
Cv Cv5 6 11 17 27 39 61 98 158
225
Valve Cracking Pressure (0.5 psi)(Horizontal Position) 0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
10.1
2 3 4 5 6 7 8 10 20 30 40 50 70 100 200 300 400 500
3/8
1/2
3/4
1 11/
41
1/2
21/
2
32
Cv Cv6 7 14 20 40 80 110
162
Sizes (in):
Valve Cracking Pressure (0.5 psi)(Horizontal Position)
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
100.1
20 30 50 70 100 200 300 500 1000 2M 5M 10M 20M 50M 100M 200M
Sizes (in):
Cv Cv62 109
166
318
471
720
1384
2298
4153
4984
8307
1190
616
059
2270
5
4707
1
5399
3
2 21/
23 4 5 6 8 10 12 14 16 18 20 24 30 36
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
30 40 50 70 100 200 300 500 700 1000 2M 3M 5M 7M 10M200.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
Cv Cv75 100
124
300
405
675
1000
1950
3050
2 21/
23 4 5 6 8 10 12Sizes (in):
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
Tel: 910-735-0000 s Fax: 910-738-3848 s [email protected] s www.titanfci.com290 Corporate Drive s PO Box 7408 s Lumberton, NC 28358
TITAN FLOW CONTROL, INC.
• These curves are theoretical; actual results may vary depending on installation conditions and other variables. Use these values for reference only.
• The above pressure drop charts are based upon 1/8" perforated screens and baskets handling clean water at 60 °F during ideal inlet and outlet conditions. Therefore, they should only be used for estimation purposes.
• For fluids other than water, multiply the pressure drop (Δ P) obtained from the charts by the specific gravity of the fluid in question.
• For mesh lined screens, multiply the pressure drop (Δ P) obtained from the charts by the corresponding correction factor shown in the Cv correction table.
Style: Wafer Type, Double Disc Check Valve Style: Flanged, Control Check Valve (Tri-Flow)Models: CV 41-DI, CV 42-CS/SS, CV 44-CS/SS Model: TF 21-CI (Disc in the full open position)
0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
2 21/
2
3 4 5 6 8 10 12 14 16 18 20 24Sizes (in): 30 36 42 48
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
110
175
350
550
850
1500
2400
3700
5400
8250
1040
014
200
2300
0
62Cv Cv3700
055
200
9200
011
7500
10 20 30 50 70 100 200 300 500 1M 2M 5M 10M 20M 50M 100M 400M 20 30 40 50 70 100 200 300 500 700 1M 2M 3M 5M 10M 20M0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
2 21/
2
3 4 5 6 8 10 12 14
Cv Cv125
80 290
700
1260
2150
3320
4016
Sizes (in):
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
Style: Wafer Type, Silent Check Valve Style: Globe Type, Silent Check ValveModels: CV 90-DB/DS, CV 91-SS Models: CV 50-DI, CV 51-CS/SS, CV 52-DB/DS
10 20 30 40 50 70 100 200 300 500 700 1M 2M 3M 5M 10M0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
60 95 310
450
750
1250
1800
Sizes (in): 2 21/
2
3 4 5 6 8 10 12
Cv Cv150
230
Valve Cracking Pressure (0.5 psi)(Horizontal Position)
20 30 40 50 70 100 200 300 500 700 1M 2M 3M 5M 10M 20M 50M0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
567
10
2 21/
23 4 5 6 8 10 12 14 16 18 20 24
65Cv Cv
Sizes (in):
105
150
265
410
600
1100
1800
2500
3100
4300
5000
6300
9800
Valve Cracking Pressure (0.5 psi)(Horizontal Position)
1500
0
30
CVPDC-0914
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x - axis)
Style: High Pressure - Wafer Type, Double Disc CV Style: High Pressure - Wafer Type, Double Disc CVModel: CV 46-CS/SS Model: CV 47-CS/SS
10 20 30 50 70 100 200 300 500 1M 2M 5M 10M 20M 50M0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
5
7
10
Cv 95 140
200
400
580
1350
1850
2500
4800
5520
7500
1030
011
100
45
2 21/
23 4 5 6 8 10 12 14 16 18 20 24Sizes (in):
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
Cv
10 20 30 50 70 100 200 300 500 1M 2M 5M 10M 20M 50M0.1
0.2
0.3
0.4
0.5
0.7
1
2
3
4
5
7
10
2 21/
23 4 5 6 8 10 12 14 16 18 20 24Sizes (in):
80 120
190
380
500
1500
2900
4520
7000
9000
1000
1400
0
1900
40Cv Cv
Valve Cracking Pressure (0.25 psi)(Horizontal Position)
TITAN TITAN FLOW CONTROL, INC f CHECK VALVE PRESSURE DROP CHARTS